Merge tag 'v3.3-rc7' into x86/mce

Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Documentation/DocBook/device-drivers.tmpl

@@ -102,9 +102,12 @@ X!Iinclude/linux/kobject.h
 !Iinclude/linux/device.h
      </sect1>
      <sect1><title>Device Drivers Base</title>
+!Idrivers/base/init.c
 !Edrivers/base/driver.c
 !Edrivers/base/core.c
+!Edrivers/base/syscore.c
 !Edrivers/base/class.c
+!Idrivers/base/node.c
 !Edrivers/base/firmware_class.c
 !Edrivers/base/transport_class.c
 <!-- Cannot be included, because
@@ -113,13 +116,18 @@ X!Iinclude/linux/kobject.h
      exceed allowed 44 characters maximum
 X!Edrivers/base/attribute_container.c
 -->
-!Edrivers/base/sys.c
+!Edrivers/base/dd.c
 <!--
 X!Edrivers/base/interface.c
 -->
 !Iinclude/linux/platform_device.h
 !Edrivers/base/platform.c
 !Edrivers/base/bus.c
+     </sect1>
+     <sect1><title>Device Drivers DMA Management</title>
+!Edrivers/base/dma-buf.c
+!Edrivers/base/dma-coherent.c
+!Edrivers/base/dma-mapping.c
      </sect1>
      <sect1><title>Device Drivers Power Management</title>
 !Edrivers/base/power/main.c
@@ -219,7 +227,7 @@ X!Isound/sound_firmware.c
   <chapter id="uart16x50">
      <title>16x50 UART Driver</title>
 !Edrivers/tty/serial/serial_core.c
-!Edrivers/tty/serial/8250.c
+!Edrivers/tty/serial/8250/8250.c
   </chapter>
 
   <chapter id="fbdev">

Documentation/devicetree/bindings/gpio/led.txt

@@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device.  Each
 node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
-  low LEDs should be indicated using flags in the GPIO specifier.
+- gpios :  Should specify the LED's GPIO, see "gpios property" in
+  Documentation/devicetree/gpio.txt.  Active low LEDs should be
+  indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
 - linux,default-trigger :  (optional) This parameter, if present, is a

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -30,6 +30,7 @@ national	National Semiconductor
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
+picochip	Picochip Ltd
 powervr	Imagination Technologies
 qcom	Qualcomm, Inc.
 ramtron	Ramtron International

Documentation/driver-model/devres.txt

@@ -233,6 +233,10 @@ certainly invest a bit more effort into libata core layer).
   6. List of managed interfaces
   -----------------------------
 
+MEM
+  devm_kzalloc()
+  devm_kfree()
+
 IO region
   devm_request_region()
   devm_request_mem_region()

Documentation/feature-removal-schedule.txt

@@ -510,3 +510,17 @@ Why:	The pci_scan_bus_parented() interface creates a new root bus.  The
 	convert to using pci_scan_root_bus() so they can supply a list of
 	bus resources when the bus is created.
 Who:	Bjorn Helgaas <bhelgaas@google.com>
+
+----------------------------
+
+What:	The CAP9 SoC family will be removed
+When:	3.4
+Files:	arch/arm/mach-at91/at91cap9.c
+	arch/arm/mach-at91/at91cap9_devices.c
+	arch/arm/mach-at91/include/mach/at91cap9.h
+	arch/arm/mach-at91/include/mach/at91cap9_matrix.h
+	arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h
+	arch/arm/mach-at91/board-cap9adk.c
+Why:	The code is not actively maintained and platforms are now hard to find.
+Who:	Nicolas Ferre <nicolas.ferre@atmel.com>
+	Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Documentation/hwmon/jc42

@@ -7,21 +7,29 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * IDT TSE2002B3, TS3000B3
-    Prefix: 'tse2002b3', 'ts3000b3'
+  * Atmel AT30TS00
+    Prefix: 'at30ts00'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.idt.com/products/getdoc.cfm?docid=18715691
-	http://www.idt.com/products/getdoc.cfm?docid=18715692
+	http://www.atmel.com/Images/doc8585.pdf
+  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
+    Prefix: 'tse2002', 'ts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
+	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -48,6 +56,12 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+  * ST Microelectronics STTS2002, STTS3000
+    Prefix: 'stts2002', 'stts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f

Documentation/input/alps.txt

@@ -13,7 +13,8 @@ Detection
 
 All ALPS touchpads should respond to the "E6 report" command sequence:
 E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or
-00-00-64.
+00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s
+if some buttons are pressed.
 
 If the E6 report is successful, the touchpad model is identified using the "E7
 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is

Documentation/input/event-codes.txt

@@ -17,11 +17,11 @@ reports supported by a device are also provided by sysfs in
 class/input/event*/device/capabilities/, and the properties of a device are
 provided in class/input/event*/device/properties.
 
-Types:
-==========
-Types are groupings of codes under a logical input construct. Each type has a
-set of applicable codes to be used in generating events. See the Codes section
-for details on valid codes for each type.
+Event types:
+===========
+Event types are groupings of codes under a logical input construct. Each
+type has a set of applicable codes to be used in generating events. See the
+Codes section for details on valid codes for each type.
 
 * EV_SYN:
   - Used as markers to separate events. Events may be separated in time or in
@@ -63,9 +63,9 @@ for details on valid codes for each type.
 * EV_FF_STATUS:
   - Used to receive force feedback device status.
 
-Codes:
-==========
-Codes define the precise type of event.
+Event codes:
+===========
+Event codes define the precise type of event.
 
 EV_SYN:
 ----------
@@ -220,6 +220,56 @@ EV_PWR:
 EV_PWR events are a special type of event used specifically for power
 mangement. Its usage is not well defined. To be addressed later.
 
+Device properties:
+=================
+Normally, userspace sets up an input device based on the data it emits,
+i.e., the event types. In the case of two devices emitting the same event
+types, additional information can be provided in the form of device
+properties.
+
+INPUT_PROP_DIRECT + INPUT_PROP_POINTER:
+--------------------------------------
+The INPUT_PROP_DIRECT property indicates that device coordinates should be
+directly mapped to screen coordinates (not taking into account trivial
+transformations, such as scaling, flipping and rotating). Non-direct input
+devices require non-trivial transformation, such as absolute to relative
+transformation for touchpads. Typical direct input devices: touchscreens,
+drawing tablets; non-direct devices: touchpads, mice.
+
+The INPUT_PROP_POINTER property indicates that the device is not transposed
+on the screen and thus requires use of an on-screen pointer to trace user's
+movements.  Typical pointer devices: touchpads, tablets, mice; non-pointer
+device: touchscreen.
+
+If neither INPUT_PROP_DIRECT or INPUT_PROP_POINTER are set, the property is
+considered undefined and the device type should be deduced in the
+traditional way, using emitted event types.
+
+INPUT_PROP_BUTTONPAD:
+--------------------
+For touchpads where the button is placed beneath the surface, such that
+pressing down on the pad causes a button click, this property should be
+set. Common in clickpad notebooks and macbooks from 2009 and onwards.
+
+Originally, the buttonpad property was coded into the bcm5974 driver
+version field under the name integrated button. For backwards
+compatibility, both methods need to be checked in userspace.
+
+INPUT_PROP_SEMI_MT:
+------------------
+Some touchpads, most common between 2008 and 2011, can detect the presence
+of multiple contacts without resolving the individual positions; only the
+number of contacts and a rectangular shape is known. For such
+touchpads, the semi-mt property should be set.
+
+Depending on the device, the rectangle may enclose all touches, like a
+bounding box, or just some of them, for instance the two most recent
+touches. The diversity makes the rectangle of limited use, but some
+gestures can normally be extracted from it.
+
+If INPUT_PROP_SEMI_MT is not set, the device is assumed to be a true MT
+device.
+
 Guidelines:
 ==========
 The guidelines below ensure proper single-touch and multi-finger functionality.
@@ -240,6 +290,8 @@ used to report when a touch is active on the screen.
 BTN_{MOUSE,LEFT,MIDDLE,RIGHT} must not be reported as the result of touch
 contact. BTN_TOOL_<name> events should be reported where possible.
 
+For new hardware, INPUT_PROP_DIRECT should be set.
+
 Trackpads:
 ----------
 Legacy trackpads that only provide relative position information must report
@@ -250,6 +302,8 @@ location of the touch. BTN_TOUCH should be used to report when a touch is active
 on the trackpad. Where multi-finger support is available, BTN_TOOL_<name> should
 be used to report the number of touches active on the trackpad.
 
+For new hardware, INPUT_PROP_POINTER should be set.
+
 Tablets:
 ----------
 BTN_TOOL_<name> events must be reported when a stylus or other tool is active on
@@ -260,3 +314,5 @@ button may be used for buttons on the tablet except BTN_{MOUSE,LEFT}.
 BTN_{0,1,2,etc} are good generic codes for unlabeled buttons. Do not use
 meaningful buttons, like BTN_FORWARD, unless the button is labeled for that
 purpose on the device.
+
+For new hardware, both INPUT_PROP_DIRECT and INPUT_PROP_POINTER should be set.

Documentation/kernel-parameters.txt

@@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 			default: off.
 
+	printk.always_kmsg_dump=
+			Trigger kmsg_dump for cases other than kernel oops or
+			panics
+			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
+			default: disabled
+
 	printk.time=	Show timing data prefixed to each printk message line
 			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
 

Documentation/pinctrl.txt

@@ -857,42 +857,41 @@ case), we define a mapping like this:
 
 ...
 {
-	.name "2bit"
+	.name = "2bit"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "mmc0",
 	.group = "mmc0_1_grp",
 	.dev_name = "foo-mmc.0",
 },
 {
-	.name "4bit"
+	.name = "4bit"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "mmc0",
 	.group = "mmc0_1_grp",
 	.dev_name = "foo-mmc.0",
 },
 {
-	.name "4bit"
+	.name = "4bit"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "mmc0",
 	.group = "mmc0_2_grp",
 	.dev_name = "foo-mmc.0",
 },
 {
-	.name "8bit"
+	.name = "8bit"
 	.ctrl_dev_name = "pinctrl-foo",
-	.function = "mmc0",
 	.group = "mmc0_1_grp",
 	.dev_name = "foo-mmc.0",
 },
 {
-	.name "8bit"
+	.name = "8bit"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "mmc0",
 	.group = "mmc0_2_grp",
 	.dev_name = "foo-mmc.0",
 },
 {
-	.name "8bit"
+	.name = "8bit"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "mmc0",
 	.group = "mmc0_3_grp",
@@ -995,7 +994,7 @@ This is enabled by simply setting the .hog_on_boot field in the map to true,
 like this:
 
 {
-	.name "POWERMAP"
+	.name = "POWERMAP"
 	.ctrl_dev_name = "pinctrl-foo",
 	.function = "power_func",
 	.hog_on_boot = true,
@@ -1025,7 +1024,7 @@ it, disables and releases it, and muxes it in on the pins defined by group B:
 
 foo_switch()
 {
-	struct pinmux pmx;
+	struct pinmux *pmx;
 
 	/* Enable on position A */
 	pmx = pinmux_get(&device, "spi0-pos-A");

Documentation/stable_kernel_rules.txt

@@ -25,7 +25,8 @@ Procedure for submitting patches to the -stable tree:
 
  - Send the patch, after verifying that it follows the above rules, to
    stable@vger.kernel.org.  You must note the upstream commit ID in the
-   changelog of your submission.
+   changelog of your submission, as well as the kernel version you wish
+   it to be applied to.
  - To have the patch automatically included in the stable tree, add the tag
      Cc: stable@vger.kernel.org
    in the sign-off area. Once the patch is merged it will be applied to

Documentation/sysctl/kernel.txt

@@ -601,6 +601,8 @@ can be ORed together:
         instead of using the one provided by the hardware.
  512 - A kernel warning has occurred.
 1024 - A module from drivers/staging was loaded.
+2048 - The system is working around a severe firmware bug.
+4096 - An out-of-tree module has been loaded.
 
 ==============================================================
 

Documentation/virtual/00-INDEX

@@ -4,8 +4,6 @@ Virtualization support in the Linux kernel.
 	- this file.
 kvm/
 	- Kernel Virtual Machine.  See also http://linux-kvm.org
-lguest/
-	- Extremely simple hypervisor for experimental/educational use.
 uml/
 	- User Mode Linux, builds/runs Linux kernel as a userspace program.
 virtio.txt

MAINTAINERS

@@ -159,7 +159,7 @@ S:	Maintained
 F:	drivers/net/ethernet/realtek/r8169.c
 
 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	linux-serial@vger.kernel.org
 W:	http://serial.sourceforge.net
 S:	Maintained
@@ -269,7 +269,6 @@ S:	Orphan
 F:	drivers/platform/x86/wmi.c
 
 AD1889 ALSA SOUND DRIVER
-M:	Kyle McMartin <kyle@mcmartin.ca>
 M:	Thibaut Varene <T-Bone@parisc-linux.org>
 W:	http://wiki.parisc-linux.org/AD1889
 L:	linux-parisc@vger.kernel.org
@@ -789,12 +788,6 @@ F:	arch/arm/mach-mx*/
 F:	arch/arm/mach-imx/
 F:	arch/arm/plat-mxc/
 
-ARM/FREESCALE IMX51
-M:	Amit Kucheria <amit.kucheria@canonical.com>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-F:	arch/arm/mach-mx5/
-
 ARM/FREESCALE IMX6
 M:	Shawn Guo <shawn.guo@linaro.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -969,7 +962,7 @@ F:	drivers/tty/serial/msm_serial.c
 F:	drivers/platform/msm/
 F:	drivers/*/pm8???-*
 F:	include/linux/mfd/pm8xxx/
-T:	git git://codeaurora.org/quic/kernel/davidb/linux-msm.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git
 S:	Maintained
 
 ARM/TOSA MACHINE SUPPORT
@@ -1317,7 +1310,7 @@ F:	drivers/atm/
 F:	include/linux/atm*
 
 ATMEL AT91 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.atmel.com/products/AT91/
 W:	http://www.at91.com/
@@ -1325,7 +1318,7 @@ S:	Maintained
 F:	drivers/mmc/host/at91_mci.c
 
 ATMEL AT91 / AT32 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 F:	drivers/mmc/host/atmel-mci-regs.h
@@ -1783,9 +1776,9 @@ X:	net/wireless/wext*
 
 CHAR and MISC DRIVERS
 M:	Arnd Bergmann <arnd@arndb.de>
-M:	Greg Kroah-Hartman <greg@kroah.com>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git
-S:	Maintained
+S:	Supported
 F:	drivers/char/*
 F:	drivers/misc/*
 
@@ -2287,7 +2280,7 @@ F:	drivers/acpi/dock.c
 DOCUMENTATION
 M:	Randy Dunlap <rdunlap@xenotime.net>
 L:	linux-doc@vger.kernel.org
-T:	quilt http://userweb.kernel.org/~rdunlap/kernel-doc-patches/current/
+T:	quilt http://xenotime.net/kernel-doc-patches/current/
 S:	Maintained
 F:	Documentation/
 
@@ -2320,7 +2313,7 @@ F:	lib/lru_cache.c
 F:	Documentation/blockdev/drbd/
 
 DRIVER CORE, KOBJECTS, DEBUGFS AND SYSFS
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6.git
 S:	Supported
 F:	Documentation/kobject.txt
@@ -2350,6 +2343,9 @@ F:	include/drm/i915*
 
 DRM DRIVERS FOR EXYNOS
 M:	Inki Dae <inki.dae@samsung.com>
+M:	Joonyoung Shim <jy0922.shim@samsung.com>
+M:	Seung-Woo Kim <sw0312.kim@samsung.com>
+M:	Kyungmin Park <kyungmin.park@samsung.com>
 L:	dri-devel@lists.freedesktop.org
 S:	Supported
 F:	drivers/gpu/drm/exynos
@@ -3050,7 +3046,6 @@ F:	drivers/hwspinlock/hwspinlock_*
 F:	include/linux/hwspinlock.h
 
 HARMONY SOUND DRIVER
-M:	Kyle McMartin <kyle@mcmartin.ca>
 L:	linux-parisc@vger.kernel.org
 S:	Maintained
 F:	sound/parisc/harmony.*
@@ -3321,6 +3316,12 @@ S:	Maintained
 F:	net/ieee802154/
 F:	drivers/ieee802154/
 
+IIO SUBSYSTEM AND DRIVERS
+M:	Jonathan Cameron <jic23@cam.ac.uk>
+L:	linux-iio@vger.kernel.org
+S:	Maintained
+F:	drivers/staging/iio/
+
 IKANOS/ADI EAGLE ADSL USB DRIVER
 M:	Matthieu Castet <castet.matthieu@free.fr>
 M:	Stanislaw Gruszka <stf_xl@wp.pl>
@@ -3779,7 +3780,7 @@ F:	Documentation/kdump/
 
 KERNEL AUTOMOUNTER v4 (AUTOFS4)
 M:	Ian Kent <raven@themaw.net>
-L:	autofs@linux.kernel.org
+L:	autofs@vger.kernel.org
 S:	Maintained
 F:	fs/autofs4/
 
@@ -3989,11 +3990,11 @@ M:	Rusty Russell <rusty@rustcorp.com.au>
 L:	lguest@lists.ozlabs.org
 W:	http://lguest.ozlabs.org/
 S:	Odd Fixes
-F:	Documentation/virtual/lguest/
+F:	arch/x86/include/asm/lguest*.h
 F:	arch/x86/lguest/
 F:	drivers/lguest/
 F:	include/linux/lguest*.h
-F:	arch/x86/include/asm/lguest*.h
+F:	tools/lguest/
 
 LINUX FOR IBM pSERIES (RS/6000)
 M:	Paul Mackerras <paulus@au.ibm.com>
@@ -4133,10 +4134,11 @@ L:	linux-ntfs-dev@lists.sourceforge.net
 W:	http://www.linux-ntfs.org/content/view/19/37/
 S:	Maintained
 F:	Documentation/ldm.txt
-F:	fs/partitions/ldm.*
+F:	block/partitions/ldm.*
 
 LogFS
 M:	Joern Engel <joern@logfs.org>
+M:	Prasad Joshi <prasadjoshi.linux@gmail.com>
 L:	logfs@logfs.org
 W:	logfs.org
 S:	Maintained
@@ -4278,13 +4280,6 @@ S:	Orphan
 F:	drivers/video/matrox/matroxfb_*
 F:	include/linux/matroxfb.h
 
-MAX1668 TEMPERATURE SENSOR DRIVER
-M:	"David George" <david.george@ska.ac.za>
-L:	lm-sensors@lm-sensors.org
-S:	Maintained
-F:	Documentation/hwmon/max1668
-F:	drivers/hwmon/max1668.c
-
 MAX6650 HARDWARE MONITOR AND FAN CONTROLLER DRIVER
 M:	"Hans J. Koch" <hjk@hansjkoch.de>
 L:	lm-sensors@lm-sensors.org
@@ -4690,7 +4685,7 @@ NTFS FILESYSTEM
 M:	Anton Altaparmakov <anton@tuxera.com>
 L:	linux-ntfs-dev@lists.sourceforge.net
 W:	http://www.tuxera.com/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs-2.6.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs.git
 S:	Supported
 F:	Documentation/filesystems/ntfs.txt
 F:	fs/ntfs/
@@ -5003,9 +4998,8 @@ F:	Documentation/blockdev/paride.txt
 F:	drivers/block/paride/
 
 PARISC ARCHITECTURE
-M:	Kyle McMartin <kyle@mcmartin.ca>
-M:	Helge Deller <deller@gmx.de>
 M:	"James E.J. Bottomley" <jejb@parisc-linux.org>
+M:	Helge Deller <deller@gmx.de>
 L:	linux-parisc@vger.kernel.org
 W:	http://www.parisc-linux.org/
 Q:	http://patchwork.kernel.org/project/linux-parisc/list/
@@ -5636,7 +5630,7 @@ W:	http://www.ibm.com/developerworks/linux/linux390/
 S:	Supported
 F:	arch/s390/
 F:	drivers/s390/
-F:	fs/partitions/ibm.c
+F:	block/partitions/ibm.c
 F:	Documentation/s390/
 F:	Documentation/DocBook/s390*
 
@@ -5864,7 +5858,7 @@ S:	Maintained
 F:	drivers/mmc/host/sdhci-spear.c
 
 SECURITY SUBSYSTEM
-M:	James Morris <jmorris@namei.org>
+M:	James Morris <james.l.morris@oracle.com>
 L:	linux-security-module@vger.kernel.org (suggested Cc:)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security.git
 W:	http://security.wiki.kernel.org/
@@ -5877,7 +5871,7 @@ S:	Supported
 
 SELINUX SECURITY MODULE
 M:	Stephen Smalley <sds@tycho.nsa.gov>
-M:	James Morris <jmorris@namei.org>
+M:	James Morris <james.l.morris@oracle.com>
 M:	Eric Paris <eparis@parisplace.org>
 L:	selinux@tycho.nsa.gov (subscribers-only, general discussion)
 W:	http://selinuxproject.org
@@ -6279,15 +6273,15 @@ S:	Maintained
 F:	arch/alpha/kernel/srm_env.c
 
 STABLE BRANCH
-M:	Greg Kroah-Hartman <greg@kroah.com>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	stable@vger.kernel.org
-S:	Maintained
+S:	Supported
 
 STAGING SUBSYSTEM
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging.git
 L:	devel@driverdev.osuosl.org
-S:	Maintained
+S:	Supported
 F:	drivers/staging/
 
 STAGING - AGERE HERMES II and II.5 WIRELESS DRIVERS
@@ -6399,11 +6393,6 @@ M:	Omar Ramirez Luna <omar.ramirez@ti.com>
 S:	Odd Fixes
 F:	drivers/staging/tidspbridge/
 
-STAGING - TRIDENT TVMASTER TMxxxx USB VIDEO CAPTURE DRIVERS
-L:	linux-media@vger.kernel.org
-S:	Odd Fixes
-F:	drivers/staging/tm6000/
-
 STAGING - USB ENE SM/MS CARD READER DRIVER
 M:	Al Cho <acho@novell.com>
 S:	Odd Fixes
@@ -6672,10 +6661,10 @@ S:	Maintained
 K:	^Subject:.*(?i)trivial
 
 TTY LAYER
-M:	Greg Kroah-Hartman <gregkh@suse.de>
-S:	Maintained
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
+S:	Supported
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6.git
-F:	drivers/tty/*
+F:	drivers/tty/
 F:	drivers/tty/serial/serial_core.c
 F:	include/linux/serial_core.h
 F:	include/linux/serial.h
@@ -6961,7 +6950,7 @@ S:	Maintained
 F:	drivers/usb/serial/digi_acceleport.c
 
 USB SERIAL DRIVER
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	Documentation/usb/usb-serial.txt
@@ -6976,9 +6965,8 @@ S:	Maintained
 F:	drivers/usb/serial/empeg.c
 
 USB SERIAL KEYSPAN DRIVER
-M:	Greg Kroah-Hartman <greg@kroah.com>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	linux-usb@vger.kernel.org
-W:	http://www.kroah.com/linux/
 S:	Maintained
 F:	drivers/usb/serial/*keyspan*
 
@@ -7006,7 +6994,7 @@ F:	Documentation/video4linux/sn9c102.txt
 F:	drivers/media/video/sn9c102/
 
 USB SUBSYSTEM
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	linux-usb@vger.kernel.org
 W:	http://www.linux-usb.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6.git
@@ -7093,7 +7081,7 @@ F:	fs/hppfs/
 
 USERSPACE I/O (UIO)
 M:	"Hans J. Koch" <hjk@hansjkoch.de>
-M:	Greg Kroah-Hartman <gregkh@suse.de>
+M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 S:	Maintained
 F:	Documentation/DocBook/uio-howto.tmpl
 F:	drivers/uio/
@@ -7283,7 +7271,7 @@ WATCHDOG DEVICE DRIVERS
 M:	Wim Van Sebroeck <wim@iguana.be>
 L:	linux-watchdog@vger.kernel.org
 W:	http://www.linux-watchdog.org/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
+T:	git git://www.linux-watchdog.org/linux-watchdog.git
 S:	Maintained
 F:	Documentation/watchdog/
 F:	drivers/watchdog/
@@ -7368,6 +7356,7 @@ S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	arch/arm/mach-s3c64xx/mach-crag6410*
 F:	drivers/leds/leds-wm83*.c
+F:	drivers/hwmon/wm83??-hwmon.c
 F:	drivers/input/misc/wm831x-on.c
 F:	drivers/input/touchscreen/wm831x-ts.c
 F:	drivers/input/touchscreen/wm97*.c

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc7
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

arch/alpha/include/asm/futex.h

@@ -108,7 +108,7 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 	"	lda	$31,3b-2b(%0)\n"
 	"	.previous\n"
 	:	"+r"(ret), "=&r"(prev), "=&r"(cmp)
-	:	"r"(uaddr), "r"((long)oldval), "r"(newval)
+	:	"r"(uaddr), "r"((long)(int)oldval), "r"(newval)
 	:	"memory");
 
 	*uval = prev;

arch/arm/Kconfig

@@ -754,7 +754,7 @@ config ARCH_SA1100
 	select ARCH_HAS_CPUFREQ
 	select CPU_FREQ
 	select GENERIC_CLOCKEVENTS
-	select CLKDEV_LOOKUP
+	select HAVE_CLK
 	select HAVE_SCHED_CLOCK
 	select TICK_ONESHOT
 	select ARCH_REQUIRE_GPIOLIB
@@ -825,7 +825,6 @@ config ARCH_S5PC100
 	select HAVE_CLK
 	select CLKDEV_LOOKUP
 	select CPU_V7
-	select ARM_L1_CACHE_SHIFT_6
 	select ARCH_USES_GETTIMEOFFSET
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C_RTC if RTC_CLASS
@@ -842,7 +841,6 @@ config ARCH_S5PV210
 	select HAVE_CLK
 	select CLKDEV_LOOKUP
 	select CLKSRC_MMIO
-	select ARM_L1_CACHE_SHIFT_6
 	select ARCH_HAS_CPUFREQ
 	select GENERIC_CLOCKEVENTS
 	select HAVE_SCHED_CLOCK
@@ -1282,7 +1280,7 @@ config ARM_ERRATA_743622
 	depends on CPU_V7
 	help
 	  This option enables the workaround for the 743622 Cortex-A9
-	  (r2p0..r2p2) erratum. Under very rare conditions, a faulty
+	  (r2p*) erratum. Under very rare conditions, a faulty
 	  optimisation in the Cortex-A9 Store Buffer may lead to data
 	  corruption. This workaround sets a specific bit in the diagnostic
 	  register of the Cortex-A9 which disables the Store Buffer

arch/arm/boot/.gitignore

@@ -3,3 +3,4 @@ zImage
 xipImage
 bootpImage
 uImage
+*.dtb

arch/arm/boot/dts/exynos4210.dtsi

@@ -29,6 +29,7 @@
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
+		cpu-offset = <0x8000>;
 		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
 	};
 

arch/arm/boot/dts/tegra-paz00.dts

@@ -46,11 +46,11 @@
 	};
 
 	serial@70006200 {
-		status = "disable";
+		clock-frequency = <216000000>;
 	};
 
 	serial@70006300 {
-		clock-frequency = <216000000>;
+		status = "disable";
 	};
 
 	serial@70006400 {
@@ -60,7 +60,7 @@
 	sdhci@c8000000 {
 		cd-gpios = <&gpio 173 0>; /* gpio PV5 */
 		wp-gpios = <&gpio 57 0>;  /* gpio PH1 */
-		power-gpios = <&gpio 155 0>; /* gpio PT3 */
+		power-gpios = <&gpio 169 0>; /* gpio PV1 */
 	};
 
 	sdhci@c8000200 {

arch/arm/common/gic.c

@@ -41,6 +41,7 @@
 
 #include <asm/irq.h>
 #include <asm/exception.h>
+#include <asm/smp_plat.h>
 #include <asm/mach/irq.h>
 #include <asm/hardware/gic.h>
 
@@ -352,11 +353,7 @@ static void __init gic_dist_init(struct gic_chip_data *gic)
 	unsigned int gic_irqs = gic->gic_irqs;
 	struct irq_domain *domain = &gic->domain;
 	void __iomem *base = gic_data_dist_base(gic);
-	u32 cpu = 0;
-
-#ifdef CONFIG_SMP
-	cpu = cpu_logical_map(smp_processor_id());
-#endif
+	u32 cpu = cpu_logical_map(smp_processor_id());
 
 	cpumask = 1 << cpu;
 	cpumask |= cpumask << 8;

arch/arm/common/it8152.c

@@ -320,13 +320,6 @@ err0:
 	return -EBUSY;
 }
 
-/*
- * If we set up a device for bus mastering, we need to check the latency
- * timer as we don't have even crappy BIOSes to set it properly.
- * The implementation is from arch/i386/pci/i386.c
- */
-unsigned int pcibios_max_latency = 255;
-
 /* ITE bridge requires setting latency timer to avoid early bus access
    termination by PCI bus master devices
 */

arch/arm/common/pl330.c

@@ -1502,12 +1502,13 @@ int pl330_chan_ctrl(void *ch_id, enum pl330_chan_op op)
 	struct pl330_thread *thrd = ch_id;
 	struct pl330_dmac *pl330;
 	unsigned long flags;
-	int ret = 0, active = thrd->req_running;
+	int ret = 0, active;
 
 	if (!thrd || thrd->free || thrd->dmac->state == DYING)
 		return -EINVAL;
 
 	pl330 = thrd->dmac;
+	active = thrd->req_running;
 
 	spin_lock_irqsave(&pl330->lock, flags);
 

arch/arm/include/asm/assembler.h

@@ -137,6 +137,11 @@
 	disable_irq
 	.endm
 
+	.macro	save_and_disable_irqs_notrace, oldcpsr
+	mrs	\oldcpsr, cpsr
+	disable_irq_notrace
+	.endm
+
 /*
  * Restore interrupt state previously stored in a register.  We don't
  * guarantee that this will preserve the flags.
@@ -237,7 +242,7 @@
  */
 #ifdef CONFIG_THUMB2_KERNEL
 
-	.macro	usraccoff, instr, reg, ptr, inc, off, cond, abort, t=T()
+	.macro	usraccoff, instr, reg, ptr, inc, off, cond, abort, t=TUSER()
 9999:
 	.if	\inc == 1
 	\instr\cond\()b\()\t\().w \reg, [\ptr, #\off]
@@ -277,7 +282,7 @@
 
 #else	/* !CONFIG_THUMB2_KERNEL */
 
-	.macro	usracc, instr, reg, ptr, inc, cond, rept, abort, t=T()
+	.macro	usracc, instr, reg, ptr, inc, cond, rept, abort, t=TUSER()
 	.rept	\rept
 9999:
 	.if	\inc == 1

arch/arm/include/asm/domain.h

@@ -83,9 +83,9 @@
  * instructions (inline assembly)
  */
 #ifdef CONFIG_CPU_USE_DOMAINS
-#define T(instr)	#instr "t"
+#define TUSER(instr)	#instr "t"
 #else
-#define T(instr)	#instr
+#define TUSER(instr)	#instr
 #endif
 
 #else /* __ASSEMBLY__ */
@@ -95,9 +95,9 @@
  * instructions
  */
 #ifdef CONFIG_CPU_USE_DOMAINS
-#define T(instr)	instr ## t
+#define TUSER(instr)	instr ## t
 #else
-#define T(instr)	instr
+#define TUSER(instr)	instr
 #endif
 
 #endif /* __ASSEMBLY__ */

arch/arm/include/asm/futex.h

@@ -75,9 +75,9 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 
 #define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg)	\
 	__asm__ __volatile__(					\
-	"1:	" T(ldr) "	%1, [%3]\n"			\
+	"1:	" TUSER(ldr) "	%1, [%3]\n"			\
 	"	" insn "\n"					\
-	"2:	" T(str) "	%0, [%3]\n"			\
+	"2:	" TUSER(str) "	%0, [%3]\n"			\
 	"	mov	%0, #0\n"				\
 	__futex_atomic_ex_table("%5")				\
 	: "=&r" (ret), "=&r" (oldval), "=&r" (tmp)		\
@@ -95,10 +95,10 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 		return -EFAULT;
 
 	__asm__ __volatile__("@futex_atomic_cmpxchg_inatomic\n"
-	"1:	" T(ldr) "	%1, [%4]\n"
+	"1:	" TUSER(ldr) "	%1, [%4]\n"
 	"	teq	%1, %2\n"
 	"	it	eq	@ explicit IT needed for the 2b label\n"
-	"2:	" T(streq) "	%3, [%4]\n"
+	"2:	" TUSER(streq) "	%3, [%4]\n"
 	__futex_atomic_ex_table("%5")
 	: "+r" (ret), "=&r" (val)
 	: "r" (oldval), "r" (newval), "r" (uaddr), "Ir" (-EFAULT)

arch/arm/include/asm/hardware/pl330.h

@@ -41,7 +41,7 @@ enum pl330_dstcachectrl {
 	DCCTRL1, /* Bufferable only */
 	DCCTRL2, /* Cacheable, but do not allocate */
 	DCCTRL3, /* Cacheable and bufferable, but do not allocate */
-	DINVALID1 = 8,
+	DINVALID1,              /* AWCACHE = 0x1000 */
 	DINVALID2,
 	DCCTRL6, /* Cacheable write-through, allocate on writes only */
 	DCCTRL7, /* Cacheable write-back, allocate on writes only */

arch/arm/include/asm/pmu.h

@@ -134,7 +134,7 @@ int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type);
 
 u64 armpmu_event_update(struct perf_event *event,
 			struct hw_perf_event *hwc,
-			int idx, int overflow);
+			int idx);
 
 int armpmu_event_set_period(struct perf_event *event,
 			    struct hw_perf_event *hwc,

arch/arm/include/asm/processor.h

@@ -22,6 +22,7 @@
 #include <asm/hw_breakpoint.h>
 #include <asm/ptrace.h>
 #include <asm/types.h>
+#include <asm/system.h>
 
 #ifdef __KERNEL__
 #define STACK_TOP	((current->personality & ADDR_LIMIT_32BIT) ? \

arch/arm/include/asm/smp.h

@@ -70,12 +70,6 @@ extern void platform_secondary_init(unsigned int cpu);
  */
 extern void platform_smp_prepare_cpus(unsigned int);
 
-/*
- * Logical CPU mapping.
- */
-extern int __cpu_logical_map[NR_CPUS];
-#define cpu_logical_map(cpu)	__cpu_logical_map[cpu]
-
 /*
  * Initial data for bringing up a secondary CPU.
  */

arch/arm/include/asm/smp_plat.h

@@ -43,4 +43,10 @@ static inline int cache_ops_need_broadcast(void)
 }
 #endif
 
+/*
+ * Logical CPU mapping.
+ */
+extern int __cpu_logical_map[];
+#define cpu_logical_map(cpu)	__cpu_logical_map[cpu]
+
 #endif

arch/arm/include/asm/tlb.h

@@ -198,7 +198,15 @@ static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte,
 	unsigned long addr)
 {
 	pgtable_page_dtor(pte);
-	tlb_add_flush(tlb, addr);
+
+	/*
+	 * With the classic ARM MMU, a pte page has two corresponding pmd
+	 * entries, each covering 1MB.
+	 */
+	addr &= PMD_MASK;
+	tlb_add_flush(tlb, addr + SZ_1M - PAGE_SIZE);
+	tlb_add_flush(tlb, addr + SZ_1M);
+
 	tlb_remove_page(tlb, pte);
 }
 

arch/arm/include/asm/uaccess.h

@@ -227,7 +227,7 @@ do {									\
 
 #define __get_user_asm_byte(x,addr,err)				\
 	__asm__ __volatile__(					\
-	"1:	" T(ldrb) "	%1,[%2],#0\n"			\
+	"1:	" TUSER(ldrb) "	%1,[%2],#0\n"			\
 	"2:\n"							\
 	"	.pushsection .fixup,\"ax\"\n"			\
 	"	.align	2\n"					\
@@ -263,7 +263,7 @@ do {									\
 
 #define __get_user_asm_word(x,addr,err)				\
 	__asm__ __volatile__(					\
-	"1:	" T(ldr) "	%1,[%2],#0\n"			\
+	"1:	" TUSER(ldr) "	%1,[%2],#0\n"			\
 	"2:\n"							\
 	"	.pushsection .fixup,\"ax\"\n"			\
 	"	.align	2\n"					\
@@ -308,7 +308,7 @@ do {									\
 
 #define __put_user_asm_byte(x,__pu_addr,err)			\
 	__asm__ __volatile__(					\
-	"1:	" T(strb) "	%1,[%2],#0\n"			\
+	"1:	" TUSER(strb) "	%1,[%2],#0\n"			\
 	"2:\n"							\
 	"	.pushsection .fixup,\"ax\"\n"			\
 	"	.align	2\n"					\
@@ -341,7 +341,7 @@ do {									\
 
 #define __put_user_asm_word(x,__pu_addr,err)			\
 	__asm__ __volatile__(					\
-	"1:	" T(str) "	%1,[%2],#0\n"			\
+	"1:	" TUSER(str) "	%1,[%2],#0\n"			\
 	"2:\n"							\
 	"	.pushsection .fixup,\"ax\"\n"			\
 	"	.align	2\n"					\
@@ -366,10 +366,10 @@ do {									\
 
 #define __put_user_asm_dword(x,__pu_addr,err)			\
 	__asm__ __volatile__(					\
- ARM(	"1:	" T(str) "	" __reg_oper1 ", [%1], #4\n"	)	\
- ARM(	"2:	" T(str) "	" __reg_oper0 ", [%1]\n"	)	\
- THUMB(	"1:	" T(str) "	" __reg_oper1 ", [%1]\n"	)	\
- THUMB(	"2:	" T(str) "	" __reg_oper0 ", [%1, #4]\n"	)	\
+ ARM(	"1:	" TUSER(str) "	" __reg_oper1 ", [%1], #4\n"	) \
+ ARM(	"2:	" TUSER(str) "	" __reg_oper0 ", [%1]\n"	) \
+ THUMB(	"1:	" TUSER(str) "	" __reg_oper1 ", [%1]\n"	) \
+ THUMB(	"2:	" TUSER(str) "	" __reg_oper0 ", [%1, #4]\n"	) \
 	"3:\n"							\
 	"	.pushsection .fixup,\"ax\"\n"			\
 	"	.align	2\n"					\

arch/arm/kernel/ecard.c

@@ -242,6 +242,7 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
 
+	vma.vm_flags = VM_EXEC;
 	vma.vm_mm = mm;
 
 	flush_tlb_range(&vma, IO_START, IO_START + IO_SIZE);

arch/arm/kernel/entry-armv.S

@@ -790,7 +790,7 @@ __kuser_cmpxchg64:				@ 0xffff0f60
 	smp_dmb	arm
 	rsbs	r0, r3, #0			@ set returned val and C flag
 	ldmfd	sp!, {r4, r5, r6, r7}
-	bx	lr
+	usr_ret	lr
 
 #elif !defined(CONFIG_SMP)
 

arch/arm/kernel/entry-common.S

@@ -149,6 +149,11 @@ ENDPROC(ret_from_fork)
 #endif
 #endif
 
+.macro mcount_adjust_addr rd, rn
+	bic	\rd, \rn, #1		@ clear the Thumb bit if present
+	sub	\rd, \rd, #MCOUNT_INSN_SIZE
+.endm
+
 .macro __mcount suffix
 	mcount_enter
 	ldr	r0, =ftrace_trace_function
@@ -173,8 +178,7 @@ ENDPROC(ret_from_fork)
 	mcount_exit
 
 1: 	mcount_get_lr	r1			@ lr of instrumented func
-	mov	r0, lr				@ instrumented function
-	sub	r0, r0, #MCOUNT_INSN_SIZE
+	mcount_adjust_addr	r0, lr		@ instrumented function
 	adr	lr, BSYM(2f)
 	mov	pc, r2
 2:	mcount_exit
@@ -184,8 +188,7 @@ ENDPROC(ret_from_fork)
 	mcount_enter
 
 	mcount_get_lr	r1			@ lr of instrumented func
-	mov	r0, lr				@ instrumented function
-	sub	r0, r0, #MCOUNT_INSN_SIZE
+	mcount_adjust_addr	r0, lr		@ instrumented function
 
 	.globl ftrace_call\suffix
 ftrace_call\suffix:
@@ -205,11 +208,11 @@ ftrace_graph_call\suffix:
 #ifdef CONFIG_DYNAMIC_FTRACE
 	@ called from __ftrace_caller, saved in mcount_enter
 	ldr	r1, [sp, #16]		@ instrumented routine (func)
+	mcount_adjust_addr	r1, r1
 #else
 	@ called from __mcount, untouched in lr
-	mov	r1, lr			@ instrumented routine (func)
+	mcount_adjust_addr	r1, lr	@ instrumented routine (func)
 #endif
-	sub	r1, r1, #MCOUNT_INSN_SIZE
 	mov	r2, fp			@ frame pointer
 	bl	prepare_ftrace_return
 	mcount_exit

arch/arm/kernel/perf_event.c

@@ -180,7 +180,7 @@ armpmu_event_set_period(struct perf_event *event,
 u64
 armpmu_event_update(struct perf_event *event,
 		    struct hw_perf_event *hwc,
-		    int idx, int overflow)
+		    int idx)
 {
 	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	u64 delta, prev_raw_count, new_raw_count;
@@ -193,13 +193,7 @@ again:
 			     new_raw_count) != prev_raw_count)
 		goto again;
 
-	new_raw_count &= armpmu->max_period;
-	prev_raw_count &= armpmu->max_period;
-
-	if (overflow)
-		delta = armpmu->max_period - prev_raw_count + new_raw_count + 1;
-	else
-		delta = new_raw_count - prev_raw_count;
+	delta = (new_raw_count - prev_raw_count) & armpmu->max_period;
 
 	local64_add(delta, &event->count);
 	local64_sub(delta, &hwc->period_left);
@@ -216,7 +210,7 @@ armpmu_read(struct perf_event *event)
 	if (hwc->idx < 0)
 		return;
 
-	armpmu_event_update(event, hwc, hwc->idx, 0);
+	armpmu_event_update(event, hwc, hwc->idx);
 }
 
 static void
@@ -232,7 +226,7 @@ armpmu_stop(struct perf_event *event, int flags)
 	if (!(hwc->state & PERF_HES_STOPPED)) {
 		armpmu->disable(hwc, hwc->idx);
 		barrier(); /* why? */
-		armpmu_event_update(event, hwc, hwc->idx, 0);
+		armpmu_event_update(event, hwc, hwc->idx);
 		hwc->state |= PERF_HES_STOPPED | PERF_HES_UPTODATE;
 	}
 }
@@ -518,7 +512,13 @@ __hw_perf_event_init(struct perf_event *event)
 	hwc->config_base	    |= (unsigned long)mapping;
 
 	if (!hwc->sample_period) {
-		hwc->sample_period  = armpmu->max_period;
+		/*
+		 * For non-sampling runs, limit the sample_period to half
+		 * of the counter width. That way, the new counter value
+		 * is far less likely to overtake the previous one unless
+		 * you have some serious IRQ latency issues.
+		 */
+		hwc->sample_period  = armpmu->max_period >> 1;
 		hwc->last_period    = hwc->sample_period;
 		local64_set(&hwc->period_left, hwc->sample_period);
 	}
@@ -679,6 +679,28 @@ static void __init cpu_pmu_init(struct arm_pmu *armpmu)
 	armpmu->type = ARM_PMU_DEVICE_CPU;
 }
 
+/*
+ * PMU hardware loses all context when a CPU goes offline.
+ * When a CPU is hotplugged back in, since some hardware registers are
+ * UNKNOWN at reset, the PMU must be explicitly reset to avoid reading
+ * junk values out of them.
+ */
+static int __cpuinit pmu_cpu_notify(struct notifier_block *b,
+					unsigned long action, void *hcpu)
+{
+	if ((action & ~CPU_TASKS_FROZEN) != CPU_STARTING)
+		return NOTIFY_DONE;
+
+	if (cpu_pmu && cpu_pmu->reset)
+		cpu_pmu->reset(NULL);
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block __cpuinitdata pmu_cpu_notifier = {
+	.notifier_call = pmu_cpu_notify,
+};
+
 /*
  * CPU PMU identification and registration.
  */
@@ -730,6 +752,7 @@ init_hw_perf_events(void)
 		pr_info("enabled with %s PMU driver, %d counters available\n",
 			cpu_pmu->name, cpu_pmu->num_events);
 		cpu_pmu_init(cpu_pmu);
+		register_cpu_notifier(&pmu_cpu_notifier);
 		armpmu_register(cpu_pmu, "cpu", PERF_TYPE_RAW);
 	} else {
 		pr_info("no hardware support available\n");

arch/arm/kernel/perf_event_v6.c

@@ -467,23 +467,6 @@ armv6pmu_enable_event(struct hw_perf_event *hwc,
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
-static int counter_is_active(unsigned long pmcr, int idx)
-{
-	unsigned long mask = 0;
-	if (idx == ARMV6_CYCLE_COUNTER)
-		mask = ARMV6_PMCR_CCOUNT_IEN;
-	else if (idx == ARMV6_COUNTER0)
-		mask = ARMV6_PMCR_COUNT0_IEN;
-	else if (idx == ARMV6_COUNTER1)
-		mask = ARMV6_PMCR_COUNT1_IEN;
-
-	if (mask)
-		return pmcr & mask;
-
-	WARN_ONCE(1, "invalid counter number (%d)\n", idx);
-	return 0;
-}
-
 static irqreturn_t
 armv6pmu_handle_irq(int irq_num,
 		    void *dev)
@@ -513,7 +496,8 @@ armv6pmu_handle_irq(int irq_num,
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!counter_is_active(pmcr, idx))
+		/* Ignore if we don't have an event. */
+		if (!event)
 			continue;
 
 		/*
@@ -524,7 +508,7 @@ armv6pmu_handle_irq(int irq_num,
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

arch/arm/kernel/perf_event_v7.c

@@ -469,6 +469,20 @@ static const unsigned armv7_a5_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
 			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
 		},
 	},
+	[C(NODE)] = {
+		[C(OP_READ)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+		[C(OP_WRITE)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+		[C(OP_PREFETCH)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+	},
 };
 
 /*
@@ -579,6 +593,20 @@ static const unsigned armv7_a15_perf_cache_map[PERF_COUNT_HW_CACHE_MAX]
 			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
 		},
 	},
+	[C(NODE)] = {
+		[C(OP_READ)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+		[C(OP_WRITE)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+		[C(OP_PREFETCH)] = {
+			[C(RESULT_ACCESS)]	= CACHE_OP_UNSUPPORTED,
+			[C(RESULT_MISS)]	= CACHE_OP_UNSUPPORTED,
+		},
+	},
 };
 
 /*
@@ -781,6 +809,11 @@ static inline int armv7_pmnc_disable_intens(int idx)
 
 	counter = ARMV7_IDX_TO_COUNTER(idx);
 	asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (BIT(counter)));
+	isb();
+	/* Clear the overflow flag in case an interrupt is pending. */
+	asm volatile("mcr p15, 0, %0, c9, c12, 3" : : "r" (BIT(counter)));
+	isb();
+
 	return idx;
 }
 
@@ -927,6 +960,10 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
+		/* Ignore if we don't have an event. */
+		if (!event)
+			continue;
+
 		/*
 		 * We have a single interrupt for all counters. Check that
 		 * each counter has overflowed before we process it.
@@ -935,7 +972,7 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

arch/arm/kernel/perf_event_xscale.c

@@ -255,11 +255,14 @@ xscale1pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
+		if (!event)
+			continue;
+
 		if (!xscale1_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -592,11 +595,14 @@ xscale2pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!xscale2_pmnc_counter_has_overflowed(pmnc, idx))
+		if (!event)
+			continue;
+
+		if (!xscale2_pmnc_counter_has_overflowed(of_flags, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx, 1);
+		armpmu_event_update(event, hwc, idx);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -663,7 +669,7 @@ xscale2pmu_enable_event(struct hw_perf_event *hwc, int idx)
 static void
 xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
-	unsigned long flags, ien, evtsel;
+	unsigned long flags, ien, evtsel, of_flags;
 	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	ien = xscale2pmu_read_int_enable();
@@ -672,26 +678,31 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	switch (idx) {
 	case XSCALE_CYCLE_COUNTER:
 		ien &= ~XSCALE2_CCOUNT_INT_EN;
+		of_flags = XSCALE2_CCOUNT_OVERFLOW;
 		break;
 	case XSCALE_COUNTER0:
 		ien &= ~XSCALE2_COUNT0_INT_EN;
 		evtsel &= ~XSCALE2_COUNT0_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT0_EVT_SHFT;
+		of_flags = XSCALE2_COUNT0_OVERFLOW;
 		break;
 	case XSCALE_COUNTER1:
 		ien &= ~XSCALE2_COUNT1_INT_EN;
 		evtsel &= ~XSCALE2_COUNT1_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT1_EVT_SHFT;
+		of_flags = XSCALE2_COUNT1_OVERFLOW;
 		break;
 	case XSCALE_COUNTER2:
 		ien &= ~XSCALE2_COUNT2_INT_EN;
 		evtsel &= ~XSCALE2_COUNT2_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT2_EVT_SHFT;
+		of_flags = XSCALE2_COUNT2_OVERFLOW;
 		break;
 	case XSCALE_COUNTER3:
 		ien &= ~XSCALE2_COUNT3_INT_EN;
 		evtsel &= ~XSCALE2_COUNT3_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT3_EVT_SHFT;
+		of_flags = XSCALE2_COUNT3_OVERFLOW;
 		break;
 	default:
 		WARN_ONCE(1, "invalid counter number (%d)\n", idx);
@@ -701,6 +712,7 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	xscale2pmu_write_event_select(evtsel);
 	xscale2pmu_write_int_enable(ien);
+	xscale2pmu_write_overflow_flags(of_flags);
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 

arch/arm/kernel/ptrace.c

@@ -23,6 +23,7 @@
 #include <linux/perf_event.h>
 #include <linux/hw_breakpoint.h>
 #include <linux/regset.h>
+#include <linux/audit.h>
 
 #include <asm/pgtable.h>
 #include <asm/system.h>
@@ -699,10 +700,13 @@ static int vfp_set(struct task_struct *target,
 {
 	int ret;
 	struct thread_info *thread = task_thread_info(target);
-	struct vfp_hard_struct new_vfp = thread->vfpstate.hard;
+	struct vfp_hard_struct new_vfp;
 	const size_t user_fpregs_offset = offsetof(struct user_vfp, fpregs);
 	const size_t user_fpscr_offset = offsetof(struct user_vfp, fpscr);
 
+	vfp_sync_hwstate(thread);
+	new_vfp = thread->vfpstate.hard;
+
 	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
 				  &new_vfp.fpregs,
 				  user_fpregs_offset,
@@ -723,9 +727,8 @@ static int vfp_set(struct task_struct *target,
 	if (ret)
 		return ret;
 
-	vfp_sync_hwstate(thread);
-	thread->vfpstate.hard = new_vfp;
 	vfp_flush_hwstate(thread);
+	thread->vfpstate.hard = new_vfp;
 
 	return 0;
 }
@@ -902,6 +905,12 @@ long arch_ptrace(struct task_struct *child, long request,
 	return ret;
 }
 
+#ifdef __ARMEB__
+#define AUDIT_ARCH_NR AUDIT_ARCH_ARMEB
+#else
+#define AUDIT_ARCH_NR AUDIT_ARCH_ARM
+#endif
+
 asmlinkage int syscall_trace(int why, struct pt_regs *regs, int scno)
 {
 	unsigned long ip;
@@ -916,7 +925,7 @@ asmlinkage int syscall_trace(int why, struct pt_regs *regs, int scno)
 	if (!ip)
 		audit_syscall_exit(regs);
 	else
-		audit_syscall_entry(AUDIT_ARCH_ARMEB, scno, regs->ARM_r0,
+		audit_syscall_entry(AUDIT_ARCH_NR, scno, regs->ARM_r0,
 				    regs->ARM_r1, regs->ARM_r2, regs->ARM_r3);
 
 	if (!test_thread_flag(TIF_SYSCALL_TRACE))

arch/arm/kernel/setup.c

@@ -21,7 +21,6 @@
 #include <linux/init.h>
 #include <linux/kexec.h>
 #include <linux/of_fdt.h>
-#include <linux/crash_dump.h>
 #include <linux/root_dev.h>
 #include <linux/cpu.h>
 #include <linux/interrupt.h>
@@ -160,7 +159,7 @@ static struct resource mem_res[] = {
 		.flags = IORESOURCE_MEM
 	},
 	{
-		.name = "Kernel text",
+		.name = "Kernel code",
 		.start = 0,
 		.end = 0,
 		.flags = IORESOURCE_MEM
@@ -427,6 +426,20 @@ void cpu_init(void)
 	    : "r14");
 }
 
+int __cpu_logical_map[NR_CPUS];
+
+void __init smp_setup_processor_id(void)
+{
+	int i;
+	u32 cpu = is_smp() ? read_cpuid_mpidr() & 0xff : 0;
+
+	cpu_logical_map(0) = cpu;
+	for (i = 1; i < NR_CPUS; ++i)
+		cpu_logical_map(i) = i == cpu ? 0 : i;
+
+	printk(KERN_INFO "Booting Linux on physical CPU %d\n", cpu);
+}
+
 static void __init setup_processor(void)
 {
 	struct proc_info_list *list;

arch/arm/kernel/signal.c

@@ -227,6 +227,8 @@ static int restore_vfp_context(struct vfp_sigframe __user *frame)
 	if (magic != VFP_MAGIC || size != VFP_STORAGE_SIZE)
 		return -EINVAL;
 
+	vfp_flush_hwstate(thread);
+
 	/*
 	 * Copy the floating point registers. There can be unused
 	 * registers see asm/hwcap.h for details.
@@ -251,9 +253,6 @@ static int restore_vfp_context(struct vfp_sigframe __user *frame)
 	__get_user_error(h->fpinst, &frame->ufp_exc.fpinst, err);
 	__get_user_error(h->fpinst2, &frame->ufp_exc.fpinst2, err);
 
-	if (!err)
-		vfp_flush_hwstate(thread);
-
 	return err ? -EFAULT : 0;
 }
 

arch/arm/kernel/smp.c

@@ -233,20 +233,6 @@ void __ref cpu_die(void)
 }
 #endif /* CONFIG_HOTPLUG_CPU */
 
-int __cpu_logical_map[NR_CPUS];
-
-void __init smp_setup_processor_id(void)
-{
-	int i;
-	u32 cpu = is_smp() ? read_cpuid_mpidr() & 0xff : 0;
-
-	cpu_logical_map(0) = cpu;
-	for (i = 1; i < NR_CPUS; ++i)
-		cpu_logical_map(i) = i == cpu ? 0 : i;
-
-	printk(KERN_INFO "Booting Linux on physical CPU %d\n", cpu);
-}
-
 /*
  * Called by both boot and secondaries to move global data into
  * per-processor storage.
@@ -443,9 +429,7 @@ static DEFINE_PER_CPU(struct clock_event_device, percpu_clockevent);
 static void ipi_timer(void)
 {
 	struct clock_event_device *evt = &__get_cpu_var(percpu_clockevent);
-	irq_enter();
 	evt->event_handler(evt);
-	irq_exit();
 }
 
 #ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
@@ -548,7 +532,9 @@ void handle_IPI(int ipinr, struct pt_regs *regs)
 
 	switch (ipinr) {
 	case IPI_TIMER:
+		irq_enter();
 		ipi_timer();
+		irq_exit();
 		break;
 
 	case IPI_RESCHEDULE:
@@ -556,15 +542,21 @@ void handle_IPI(int ipinr, struct pt_regs *regs)
 		break;
 
 	case IPI_CALL_FUNC:
+		irq_enter();
 		generic_smp_call_function_interrupt();
+		irq_exit();
 		break;
 
 	case IPI_CALL_FUNC_SINGLE:
+		irq_enter();
 		generic_smp_call_function_single_interrupt();
+		irq_exit();
 		break;
 
 	case IPI_CPU_STOP:
+		irq_enter();
 		ipi_cpu_stop(cpu);
+		irq_exit();
 		break;
 
 	default:

arch/arm/kernel/smp_twd.c

@@ -129,7 +129,7 @@ static struct notifier_block twd_cpufreq_nb = {
 
 static int twd_cpufreq_init(void)
 {
-	if (!IS_ERR(twd_clk))
+	if (twd_evt && *__this_cpu_ptr(twd_evt) && !IS_ERR(twd_clk))
 		return cpufreq_register_notifier(&twd_cpufreq_nb,
 			CPUFREQ_TRANSITION_NOTIFIER);
 
@@ -252,6 +252,8 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 	else
 		twd_calibrate_rate();
 
+	__raw_writel(0, twd_base + TWD_TIMER_CONTROL);
+
 	clk->name = "local_timer";
 	clk->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
 			CLOCK_EVT_FEAT_C3STOP;

arch/arm/kernel/traps.c

@@ -266,6 +266,7 @@ void die(const char *str, struct pt_regs *regs, int err)
 {
 	struct thread_info *thread = current_thread_info();
 	int ret;
+	enum bug_trap_type bug_type = BUG_TRAP_TYPE_NONE;
 
 	oops_enter();
 
@@ -273,7 +274,9 @@ void die(const char *str, struct pt_regs *regs, int err)
 	console_verbose();
 	bust_spinlocks(1);
 	if (!user_mode(regs))
-		report_bug(regs->ARM_pc, regs);
+		bug_type = report_bug(regs->ARM_pc, regs);
+	if (bug_type != BUG_TRAP_TYPE_NONE)
+		str = "Oops - BUG";
 	ret = __die(str, err, thread, regs);
 
 	if (regs && kexec_should_crash(thread->task))

arch/arm/kernel/vmlinux.lds.S

@@ -4,11 +4,13 @@
  */
 
 #include <asm-generic/vmlinux.lds.h>
+#include <asm/cache.h>
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/page.h>
 	
 #define PROC_INFO							\
+	. = ALIGN(4);							\
 	VMLINUX_SYMBOL(__proc_info_begin) = .;				\
 	*(.proc.info.init)						\
 	VMLINUX_SYMBOL(__proc_info_end) = .;
@@ -181,7 +183,7 @@ SECTIONS
 	}
 #endif
 
-	PERCPU_SECTION(32)
+	PERCPU_SECTION(L1_CACHE_BYTES)
 
 #ifdef CONFIG_XIP_KERNEL
 	__data_loc = ALIGN(4);		/* location in binary */
@@ -212,13 +214,13 @@ SECTIONS
 #endif
 
 		NOSAVE_DATA
-		CACHELINE_ALIGNED_DATA(32)
-		READ_MOSTLY_DATA(32)
+		CACHELINE_ALIGNED_DATA(L1_CACHE_BYTES)
+		READ_MOSTLY_DATA(L1_CACHE_BYTES)
 
 		/*
 		 * The exception fixup table (might need resorting at runtime)
 		 */
-		. = ALIGN(32);
+		. = ALIGN(4);
 		__start___ex_table = .;
 #ifdef CONFIG_MMU
 		*(__ex_table)

arch/arm/lib/getuser.S

@@ -31,18 +31,18 @@
 #include <asm/domain.h>
 
 ENTRY(__get_user_1)
-1:	T(ldrb)	r2, [r0]
+1: TUSER(ldrb)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__get_user_1)
 
 ENTRY(__get_user_2)
 #ifdef CONFIG_THUMB2_KERNEL
-2:	T(ldrb)	r2, [r0]
-3:	T(ldrb)	r3, [r0, #1]
+2: TUSER(ldrb)	r2, [r0]
+3: TUSER(ldrb)	r3, [r0, #1]
 #else
-2:	T(ldrb)	r2, [r0], #1
-3:	T(ldrb)	r3, [r0]
+2: TUSER(ldrb)	r2, [r0], #1
+3: TUSER(ldrb)	r3, [r0]
 #endif
 #ifndef __ARMEB__
 	orr	r2, r2, r3, lsl #8
@@ -54,7 +54,7 @@ ENTRY(__get_user_2)
 ENDPROC(__get_user_2)
 
 ENTRY(__get_user_4)
-4:	T(ldr)	r2, [r0]
+4: TUSER(ldr)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__get_user_4)

arch/arm/lib/putuser.S

@@ -31,7 +31,7 @@
 #include <asm/domain.h>
 
 ENTRY(__put_user_1)
-1:	T(strb)	r2, [r0]
+1: TUSER(strb)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__put_user_1)
@@ -40,19 +40,19 @@ ENTRY(__put_user_2)
 	mov	ip, r2, lsr #8
 #ifdef CONFIG_THUMB2_KERNEL
 #ifndef __ARMEB__
-2:	T(strb)	r2, [r0]
-3:	T(strb)	ip, [r0, #1]
+2: TUSER(strb)	r2, [r0]
+3: TUSER(strb)	ip, [r0, #1]
 #else
-2:	T(strb)	ip, [r0]
-3:	T(strb)	r2, [r0, #1]
+2: TUSER(strb)	ip, [r0]
+3: TUSER(strb)	r2, [r0, #1]
 #endif
 #else	/* !CONFIG_THUMB2_KERNEL */
 #ifndef __ARMEB__
-2:	T(strb)	r2, [r0], #1
-3:	T(strb)	ip, [r0]
+2: TUSER(strb)	r2, [r0], #1
+3: TUSER(strb)	ip, [r0]
 #else
-2:	T(strb)	ip, [r0], #1
-3:	T(strb)	r2, [r0]
+2: TUSER(strb)	ip, [r0], #1
+3: TUSER(strb)	r2, [r0]
 #endif
 #endif	/* CONFIG_THUMB2_KERNEL */
 	mov	r0, #0
@@ -60,18 +60,18 @@ ENTRY(__put_user_2)
 ENDPROC(__put_user_2)
 
 ENTRY(__put_user_4)
-4:	T(str)	r2, [r0]
+4: TUSER(str)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__put_user_4)
 
 ENTRY(__put_user_8)
 #ifdef CONFIG_THUMB2_KERNEL
-5:	T(str)	r2, [r0]
-6:	T(str)	r3, [r0, #4]
+5: TUSER(str)	r2, [r0]
+6: TUSER(str)	r3, [r0, #4]
 #else
-5:	T(str)	r2, [r0], #4
-6:	T(str)	r3, [r0]
+5: TUSER(str)	r2, [r0], #4
+6: TUSER(str)	r3, [r0]
 #endif
 	mov	r0, #0
 	mov	pc, lr

arch/arm/lib/uaccess.S

@@ -32,11 +32,11 @@
 		rsb	ip, ip, #4
 		cmp	ip, #2
 		ldrb	r3, [r1], #1
-USER(		T(strb)	r3, [r0], #1)			@ May fault
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
 		ldrgeb	r3, [r1], #1
-USER(		T(strgeb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
 		ldrgtb	r3, [r1], #1
-USER(		T(strgtb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
 		sub	r2, r2, ip
 		b	.Lc2u_dest_aligned
 
@@ -59,7 +59,7 @@ ENTRY(__copy_to_user)
 		addmi	ip, r2, #4
 		bmi	.Lc2u_0nowords
 		ldr	r3, [r1], #4
-USER(		T(str)	r3, [r0], #4)			@ May fault
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
 		mov	ip, r0, lsl #32 - PAGE_SHIFT	@ On each page, use a ld/st??t instruction
 		rsb	ip, ip, #0
 		movs	ip, ip, lsr #32 - PAGE_SHIFT
@@ -88,18 +88,18 @@ USER(		T(str)	r3, [r0], #4)			@ May fault
 		stmneia	r0!, {r3 - r4}			@ Shouldnt fault
 		tst	ip, #4
 		ldrne	r3, [r1], #4
-		T(strne) r3, [r0], #4			@ Shouldnt fault
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
 		ands	ip, ip, #3
 		beq	.Lc2u_0fupi
 .Lc2u_0nowords:	teq	ip, #0
 		beq	.Lc2u_finished
 .Lc2u_nowords:	cmp	ip, #2
 		ldrb	r3, [r1], #1
-USER(		T(strb)	r3, [r0], #1)			@ May fault
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
 		ldrgeb	r3, [r1], #1
-USER(		T(strgeb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
 		ldrgtb	r3, [r1], #1
-USER(		T(strgtb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
 		b	.Lc2u_finished
 
 .Lc2u_not_enough:
@@ -120,7 +120,7 @@ USER(		T(strgtb) r3, [r0], #1)			@ May fault
 		mov	r3, r7, pull #8
 		ldr	r7, [r1], #4
 		orr	r3, r3, r7, push #24
-USER(		T(str)	r3, [r0], #4)			@ May fault
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
 		mov	ip, r0, lsl #32 - PAGE_SHIFT
 		rsb	ip, ip, #0
 		movs	ip, ip, lsr #32 - PAGE_SHIFT
@@ -155,18 +155,18 @@ USER(		T(str)	r3, [r0], #4)			@ May fault
 		movne	r3, r7, pull #8
 		ldrne	r7, [r1], #4
 		orrne	r3, r3, r7, push #24
-		T(strne) r3, [r0], #4			@ Shouldnt fault
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
 		ands	ip, ip, #3
 		beq	.Lc2u_1fupi
 .Lc2u_1nowords:	mov	r3, r7, get_byte_1
 		teq	ip, #0
 		beq	.Lc2u_finished
 		cmp	ip, #2
-USER(		T(strb)	r3, [r0], #1)			@ May fault
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
 		movge	r3, r7, get_byte_2
-USER(		T(strgeb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
 		movgt	r3, r7, get_byte_3
-USER(		T(strgtb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
 		b	.Lc2u_finished
 
 .Lc2u_2fupi:	subs	r2, r2, #4
@@ -175,7 +175,7 @@ USER(		T(strgtb) r3, [r0], #1)			@ May fault
 		mov	r3, r7, pull #16
 		ldr	r7, [r1], #4
 		orr	r3, r3, r7, push #16
-USER(		T(str)	r3, [r0], #4)			@ May fault
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
 		mov	ip, r0, lsl #32 - PAGE_SHIFT
 		rsb	ip, ip, #0
 		movs	ip, ip, lsr #32 - PAGE_SHIFT
@@ -210,18 +210,18 @@ USER(		T(str)	r3, [r0], #4)			@ May fault
 		movne	r3, r7, pull #16
 		ldrne	r7, [r1], #4
 		orrne	r3, r3, r7, push #16
-		T(strne) r3, [r0], #4			@ Shouldnt fault
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
 		ands	ip, ip, #3
 		beq	.Lc2u_2fupi
 .Lc2u_2nowords:	mov	r3, r7, get_byte_2
 		teq	ip, #0
 		beq	.Lc2u_finished
 		cmp	ip, #2
-USER(		T(strb)	r3, [r0], #1)			@ May fault
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
 		movge	r3, r7, get_byte_3
-USER(		T(strgeb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
 		ldrgtb	r3, [r1], #0
-USER(		T(strgtb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
 		b	.Lc2u_finished
 
 .Lc2u_3fupi:	subs	r2, r2, #4
@@ -230,7 +230,7 @@ USER(		T(strgtb) r3, [r0], #1)			@ May fault
 		mov	r3, r7, pull #24
 		ldr	r7, [r1], #4
 		orr	r3, r3, r7, push #8
-USER(		T(str)	r3, [r0], #4)			@ May fault
+USER(	TUSER(	str)	r3, [r0], #4)			@ May fault
 		mov	ip, r0, lsl #32 - PAGE_SHIFT
 		rsb	ip, ip, #0
 		movs	ip, ip, lsr #32 - PAGE_SHIFT
@@ -265,18 +265,18 @@ USER(		T(str)	r3, [r0], #4)			@ May fault
 		movne	r3, r7, pull #24
 		ldrne	r7, [r1], #4
 		orrne	r3, r3, r7, push #8
-		T(strne) r3, [r0], #4			@ Shouldnt fault
+	TUSER(	strne) r3, [r0], #4			@ Shouldnt fault
 		ands	ip, ip, #3
 		beq	.Lc2u_3fupi
 .Lc2u_3nowords:	mov	r3, r7, get_byte_3
 		teq	ip, #0
 		beq	.Lc2u_finished
 		cmp	ip, #2
-USER(		T(strb)	r3, [r0], #1)			@ May fault
+USER(	TUSER(	strb)	r3, [r0], #1)			@ May fault
 		ldrgeb	r3, [r1], #1
-USER(		T(strgeb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgeb) r3, [r0], #1)			@ May fault
 		ldrgtb	r3, [r1], #0
-USER(		T(strgtb) r3, [r0], #1)			@ May fault
+USER(	TUSER(	strgtb) r3, [r0], #1)			@ May fault
 		b	.Lc2u_finished
 ENDPROC(__copy_to_user)
 
@@ -295,11 +295,11 @@ ENDPROC(__copy_to_user)
 .Lcfu_dest_not_aligned:
 		rsb	ip, ip, #4
 		cmp	ip, #2
-USER(		T(ldrb)	r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrb)	r3, [r1], #1)			@ May fault
 		strb	r3, [r0], #1
-USER(		T(ldrgeb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
 		strgeb	r3, [r0], #1
-USER(		T(ldrgtb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
 		strgtb	r3, [r0], #1
 		sub	r2, r2, ip
 		b	.Lcfu_dest_aligned
@@ -322,7 +322,7 @@ ENTRY(__copy_from_user)
 .Lcfu_0fupi:	subs	r2, r2, #4
 		addmi	ip, r2, #4
 		bmi	.Lcfu_0nowords
-USER(		T(ldr)	r3, [r1], #4)
+USER(	TUSER(	ldr)	r3, [r1], #4)
 		str	r3, [r0], #4
 		mov	ip, r1, lsl #32 - PAGE_SHIFT	@ On each page, use a ld/st??t instruction
 		rsb	ip, ip, #0
@@ -351,18 +351,18 @@ USER(		T(ldr)	r3, [r1], #4)
 		ldmneia	r1!, {r3 - r4}			@ Shouldnt fault
 		stmneia	r0!, {r3 - r4}
 		tst	ip, #4
-		T(ldrne) r3, [r1], #4			@ Shouldnt fault
+	TUSER(	ldrne) r3, [r1], #4			@ Shouldnt fault
 		strne	r3, [r0], #4
 		ands	ip, ip, #3
 		beq	.Lcfu_0fupi
 .Lcfu_0nowords:	teq	ip, #0
 		beq	.Lcfu_finished
 .Lcfu_nowords:	cmp	ip, #2
-USER(		T(ldrb)	r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrb)	r3, [r1], #1)			@ May fault
 		strb	r3, [r0], #1
-USER(		T(ldrgeb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
 		strgeb	r3, [r0], #1
-USER(		T(ldrgtb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
 		strgtb	r3, [r0], #1
 		b	.Lcfu_finished
 
@@ -375,7 +375,7 @@ USER(		T(ldrgtb) r3, [r1], #1)			@ May fault
 
 .Lcfu_src_not_aligned:
 		bic	r1, r1, #3
-USER(		T(ldr)	r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
 		cmp	ip, #2
 		bgt	.Lcfu_3fupi
 		beq	.Lcfu_2fupi
@@ -383,7 +383,7 @@ USER(		T(ldr)	r7, [r1], #4)			@ May fault
 		addmi	ip, r2, #4
 		bmi	.Lcfu_1nowords
 		mov	r3, r7, pull #8
-USER(		T(ldr)	r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
 		orr	r3, r3, r7, push #24
 		str	r3, [r0], #4
 		mov	ip, r1, lsl #32 - PAGE_SHIFT
@@ -418,7 +418,7 @@ USER(		T(ldr)	r7, [r1], #4)			@ May fault
 		stmneia	r0!, {r3 - r4}
 		tst	ip, #4
 		movne	r3, r7, pull #8
-USER(		T(ldrne) r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
 		orrne	r3, r3, r7, push #24
 		strne	r3, [r0], #4
 		ands	ip, ip, #3
@@ -438,7 +438,7 @@ USER(		T(ldrne) r7, [r1], #4)			@ May fault
 		addmi	ip, r2, #4
 		bmi	.Lcfu_2nowords
 		mov	r3, r7, pull #16
-USER(		T(ldr)	r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
 		orr	r3, r3, r7, push #16
 		str	r3, [r0], #4
 		mov	ip, r1, lsl #32 - PAGE_SHIFT
@@ -474,7 +474,7 @@ USER(		T(ldr)	r7, [r1], #4)			@ May fault
 		stmneia	r0!, {r3 - r4}
 		tst	ip, #4
 		movne	r3, r7, pull #16
-USER(		T(ldrne) r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
 		orrne	r3, r3, r7, push #16
 		strne	r3, [r0], #4
 		ands	ip, ip, #3
@@ -486,7 +486,7 @@ USER(		T(ldrne) r7, [r1], #4)			@ May fault
 		strb	r3, [r0], #1
 		movge	r3, r7, get_byte_3
 		strgeb	r3, [r0], #1
-USER(		T(ldrgtb) r3, [r1], #0)			@ May fault
+USER(	TUSER(	ldrgtb) r3, [r1], #0)			@ May fault
 		strgtb	r3, [r0], #1
 		b	.Lcfu_finished
 
@@ -494,7 +494,7 @@ USER(		T(ldrgtb) r3, [r1], #0)			@ May fault
 		addmi	ip, r2, #4
 		bmi	.Lcfu_3nowords
 		mov	r3, r7, pull #24
-USER(		T(ldr)	r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldr)	r7, [r1], #4)			@ May fault
 		orr	r3, r3, r7, push #8
 		str	r3, [r0], #4
 		mov	ip, r1, lsl #32 - PAGE_SHIFT
@@ -529,7 +529,7 @@ USER(		T(ldr)	r7, [r1], #4)			@ May fault
 		stmneia	r0!, {r3 - r4}
 		tst	ip, #4
 		movne	r3, r7, pull #24
-USER(		T(ldrne) r7, [r1], #4)			@ May fault
+USER(	TUSER(	ldrne) r7, [r1], #4)			@ May fault
 		orrne	r3, r3, r7, push #8
 		strne	r3, [r0], #4
 		ands	ip, ip, #3
@@ -539,9 +539,9 @@ USER(		T(ldrne) r7, [r1], #4)			@ May fault
 		beq	.Lcfu_finished
 		cmp	ip, #2
 		strb	r3, [r0], #1
-USER(		T(ldrgeb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgeb) r3, [r1], #1)			@ May fault
 		strgeb	r3, [r0], #1
-USER(		T(ldrgtb) r3, [r1], #1)			@ May fault
+USER(	TUSER(	ldrgtb) r3, [r1], #1)			@ May fault
 		strgtb	r3, [r0], #1
 		b	.Lcfu_finished
 ENDPROC(__copy_from_user)

arch/arm/mach-at91/Kconfig

@@ -18,6 +18,12 @@ config HAVE_AT91_USART4
 config HAVE_AT91_USART5
 	bool
 
+config AT91_SAM9_ALT_RESET
+	bool
+
+config AT91_SAM9G45_RESET
+	bool
+
 menu "Atmel AT91 System-on-Chip"
 
 choice
@@ -39,6 +45,7 @@ config ARCH_AT91SAM9260
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
 	select HAVE_NET_MACB
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9261
 	bool "AT91SAM9261"
@@ -46,6 +53,7 @@ config ARCH_AT91SAM9261
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 	select HAVE_AT91_DBGU0
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9G10
 	bool "AT91SAM9G10"
@@ -53,6 +61,7 @@ config ARCH_AT91SAM9G10
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_DBGU0
 	select HAVE_FB_ATMEL
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9263
 	bool "AT91SAM9263"
@@ -61,6 +70,7 @@ config ARCH_AT91SAM9263
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
 	select HAVE_AT91_DBGU1
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
@@ -69,6 +79,7 @@ config ARCH_AT91SAM9RL
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
 	select HAVE_AT91_DBGU0
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9G20
 	bool "AT91SAM9G20"
@@ -79,6 +90,7 @@ config ARCH_AT91SAM9G20
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
 	select HAVE_NET_MACB
+	select AT91_SAM9_ALT_RESET
 
 config ARCH_AT91SAM9G45
 	bool "AT91SAM9G45"
@@ -88,6 +100,7 @@ config ARCH_AT91SAM9G45
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
 	select HAVE_AT91_DBGU1
+	select AT91_SAM9G45_RESET
 
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
@@ -96,6 +109,7 @@ config ARCH_AT91CAP9
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
 	select HAVE_AT91_DBGU1
+	select AT91_SAM9G45_RESET
 
 config ARCH_AT91X40
 	bool "AT91x40"

arch/arm/mach-at91/Makefile

@@ -8,15 +8,17 @@ obj-n		:=
 obj-		:=
 
 obj-$(CONFIG_AT91_PMC_UNIT)	+= clock.o
+obj-$(CONFIG_AT91_SAM9_ALT_RESET) += at91sam9_alt_reset.o
+obj-$(CONFIG_AT91_SAM9G45_RESET) += at91sam9g45_reset.o
 
 # CPU-specific support
 obj-$(CONFIG_ARCH_AT91RM9200)	+= at91rm9200.o at91rm9200_time.o at91rm9200_devices.o
-obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o at91sam9_alt_reset.o
-obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o at91sam9_alt_reset.o
-obj-$(CONFIG_ARCH_AT91SAM9G10)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o at91sam9_alt_reset.o
-obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o at91sam9_alt_reset.o
-obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o at91sam9_alt_reset.o
-obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o at91sam9_alt_reset.o
+obj-$(CONFIG_ARCH_AT91SAM9260)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9261)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9G10)	+= at91sam9261.o at91sam926x_time.o at91sam9261_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9263)	+= at91sam9263.o at91sam926x_time.o at91sam9263_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9RL)	+= at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o sam9_smc.o
+obj-$(CONFIG_ARCH_AT91SAM9G20)	+= at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91SAM9G45)	+= at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91CAP9)	+= at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
 obj-$(CONFIG_ARCH_AT91X40)	+= at91x40.o at91x40_time.o

arch/arm/mach-at91/at91cap9.c

@@ -21,7 +21,6 @@
 #include <mach/cpu.h>
 #include <mach/at91cap9.h>
 #include <mach/at91_pmc.h>
-#include <mach/at91_rstc.h>
 
 #include "soc.h"
 #include "generic.h"
@@ -314,11 +313,6 @@ static struct at91_gpio_bank at91cap9_gpio[] __initdata = {
 	}
 };
 
-static void at91cap9_restart(char mode, const char *cmd)
-{
-	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
-}
-
 /* --------------------------------------------------------------------
  *  AT91CAP9 processor initialization
  * -------------------------------------------------------------------- */
@@ -331,13 +325,14 @@ static void __init at91cap9_map_io(void)
 static void __init at91cap9_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC);
+	at91_ioremap_rstc(AT91CAP9_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC);
 }
 
 static void __init at91cap9_initialize(void)
 {
-	arm_pm_restart = at91cap9_restart;
+	arm_pm_restart = at91sam9g45_restart;
 	at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
 
 	/* Register GPIO subsystem */

arch/arm/mach-at91/at91rm9200_devices.c

@@ -83,7 +83,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
  *  USB Device (Gadget)
  * -------------------------------------------------------------------- */
 
-#ifdef CONFIG_USB_AT91
+#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
 static struct at91_udc_data udc_data;
 
 static struct resource udc_resources[] = {

arch/arm/mach-at91/at91sam9260.c

@@ -323,6 +323,7 @@ static void __init at91sam9260_map_io(void)
 static void __init at91sam9260_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
+	at91_ioremap_rstc(AT91SAM9260_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
 }

arch/arm/mach-at91/at91sam9260_devices.c

@@ -84,7 +84,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
  *  USB Device (Gadget)
  * -------------------------------------------------------------------- */
 
-#ifdef CONFIG_USB_AT91
+#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
 static struct at91_udc_data udc_data;
 
 static struct resource udc_resources[] = {
@@ -1215,8 +1215,7 @@ void __init at91_add_device_serial(void) {}
  *  CF/IDE
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE) || \
-	defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
 	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
 
 static struct at91_cf_data cf0_data;
@@ -1313,10 +1312,8 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	if (data->flags & AT91_CF_TRUE_IDE)
 #if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE)
 		pdev->name = "pata_at91";
-#elif defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
-		pdev->name = "at91_ide";
 #else
-#warning "board requires AT91_CF_TRUE_IDE: enable either at91_ide or pata_at91"
+#warning "board requires AT91_CF_TRUE_IDE: enable pata_at91"
 #endif
 	else
 		pdev->name = "at91_cf";

arch/arm/mach-at91/at91sam9261.c

@@ -281,6 +281,7 @@ static void __init at91sam9261_map_io(void)
 static void __init at91sam9261_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
+	at91_ioremap_rstc(AT91SAM9261_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
 }

arch/arm/mach-at91/at91sam9261_devices.c

@@ -87,7 +87,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
  *  USB Device (Gadget)
  * -------------------------------------------------------------------- */
 
-#ifdef CONFIG_USB_AT91
+#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
 static struct at91_udc_data udc_data;
 
 static struct resource udc_resources[] = {

arch/arm/mach-at91/at91sam9263.c

@@ -301,6 +301,7 @@ static void __init at91sam9263_map_io(void)
 static void __init at91sam9263_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
+	at91_ioremap_rstc(AT91SAM9263_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
 	at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);

arch/arm/mach-at91/at91sam9263_devices.c

@@ -92,7 +92,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
  *  USB Device (Gadget)
  * -------------------------------------------------------------------- */
 
-#ifdef CONFIG_USB_AT91
+#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
 static struct at91_udc_data udc_data;
 
 static struct resource udc_resources[] = {
@@ -355,8 +355,8 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
  *  Compact Flash (PCMCIA or IDE)
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) || \
-    defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
+#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
+	defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
 
 static struct at91_cf_data cf0_data;
 
@@ -450,7 +450,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_A_periph(AT91_PIN_PD9, 0);  /* CFCE2 */
 	at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
 
-	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "at91_ide" : "at91_cf";
+	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "pata_at91" : "at91_cf";
 	platform_device_register(pdev);
 }
 #else

arch/arm/mach-at91/at91sam9_alt_reset.S

@@ -23,7 +23,8 @@
 			.globl	at91sam9_alt_restart
 
 at91sam9_alt_restart:	ldr	r0, .at91_va_base_sdramc	@ preload constants
-			ldr	r1, .at91_va_base_rstc_cr
+			ldr	r1, =at91_rstc_base
+			ldr	r1, [r1]
 
 			mov	r2, #1
 			mov	r3, #AT91_SDRAMC_LPCB_POWER_DOWN
@@ -33,11 +34,9 @@ at91sam9_alt_restart:	ldr	r0, .at91_va_base_sdramc	@ preload constants
 
 			str	r2, [r0, #AT91_SDRAMC_TR]	@ disable SDRAM access
 			str	r3, [r0, #AT91_SDRAMC_LPR]	@ power down SDRAM
-			str	r4, [r1]			@ reset processor
+			str	r4, [r1, #AT91_RSTC_CR]		@ reset processor
 
 			b	.
 
 .at91_va_base_sdramc:
 	.word AT91_VA_BASE_SYS + AT91_SDRAMC0
-.at91_va_base_rstc_cr:
-	.word AT91_VA_BASE_SYS + AT91_RSTC_CR

arch/arm/mach-at91/at91sam9g45.c

@@ -18,7 +18,6 @@
 #include <asm/mach/map.h>
 #include <mach/at91sam9g45.h>
 #include <mach/at91_pmc.h>
-#include <mach/at91_rstc.h>
 #include <mach/cpu.h>
 
 #include "soc.h"
@@ -318,11 +317,6 @@ static struct at91_gpio_bank at91sam9g45_gpio[] __initdata = {
 	}
 };
 
-static void at91sam9g45_restart(char mode, const char *cmd)
-{
-	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
-}
-
 /* --------------------------------------------------------------------
  *  AT91SAM9G45 processor initialization
  * -------------------------------------------------------------------- */
@@ -336,6 +330,7 @@ static void __init at91sam9g45_map_io(void)
 static void __init at91sam9g45_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
+	at91_ioremap_rstc(AT91SAM9G45_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
 }

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -38,10 +38,6 @@
 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
 
-static struct at_dma_platform_data atdma_pdata = {
-	.nr_channels	= 8,
-};
-
 static struct resource hdmac_resources[] = {
 	[0] = {
 		.start	= AT91SAM9G45_BASE_DMA,
@@ -56,12 +52,11 @@ static struct resource hdmac_resources[] = {
 };
 
 static struct platform_device at_hdmac_device = {
-	.name		= "at_hdmac",
+	.name		= "at91sam9g45_dma",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &hdmac_dmamask,
 				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &atdma_pdata,
 	},
 	.resource	= hdmac_resources,
 	.num_resources	= ARRAY_SIZE(hdmac_resources),
@@ -69,9 +64,15 @@ static struct platform_device at_hdmac_device = {
 
 void __init at91_add_device_hdmac(void)
 {
-	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
-	dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
-	platform_device_register(&at_hdmac_device);
+#if defined(CONFIG_OF)
+	struct device_node *of_node =
+		of_find_node_by_name(NULL, "dma-controller");
+
+	if (of_node)
+		of_node_put(of_node);
+	else
+#endif
+		platform_device_register(&at_hdmac_device);
 }
 #else
 void __init at91_add_device_hdmac(void) {}

arch/arm/mach-at91/at91sam9g45_reset.S

@@ -0,0 +1,40 @@
+/*
+ * reset AT91SAM9G45 as per errata
+ *
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcosoft.com>
+ *
+ * unless the SDRAM is cleanly shutdown before we hit the
+ * reset register it can be left driving the data bus and
+ * killing the chance of a subsequent boot from NAND
+ *
+ * GPLv2 Only
+ */
+
+#include <linux/linkage.h>
+#include <mach/hardware.h>
+#include <mach/at91sam9_ddrsdr.h>
+#include <mach/at91_rstc.h>
+
+			.arm
+
+			.globl	at91sam9g45_restart
+
+at91sam9g45_restart:
+			ldr	r0, .at91_va_base_sdramc0	@ preload constants
+			ldr	r1, =at91_rstc_base
+			ldr	r1, [r1]
+
+			mov	r2, #1
+			mov	r3, #AT91_DDRSDRC_LPCB_POWER_DOWN
+			ldr	r4, =AT91_RSTC_KEY | AT91_RSTC_PERRST | AT91_RSTC_PROCRST
+
+			.balign	32				@ align to cache line
+
+			str	r2, [r0, #AT91_DDRSDRC_RTR]	@ disable DDR0 access
+			str	r3, [r0, #AT91_DDRSDRC_LPR]	@ power down DDR0
+			str	r4, [r1, #AT91_RSTC_CR]		@ reset processor
+
+			b	.
+
+.at91_va_base_sdramc0:
+	.word AT91_VA_BASE_SYS + AT91_DDRSDRC0

arch/arm/mach-at91/at91sam9rl.c

@@ -286,6 +286,7 @@ static void __init at91sam9rl_map_io(void)
 static void __init at91sam9rl_ioremap_registers(void)
 {
 	at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
+	at91_ioremap_rstc(AT91SAM9RL_BASE_RSTC);
 	at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
 	at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
 }

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -33,10 +33,6 @@
 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
 
-static struct at_dma_platform_data atdma_pdata = {
-	.nr_channels	= 2,
-};
-
 static struct resource hdmac_resources[] = {
 	[0] = {
 		.start	= AT91SAM9RL_BASE_DMA,
@@ -51,12 +47,11 @@ static struct resource hdmac_resources[] = {
 };
 
 static struct platform_device at_hdmac_device = {
-	.name		= "at_hdmac",
+	.name		= "at91sam9rl_dma",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &hdmac_dmamask,
 				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &atdma_pdata,
 	},
 	.resource	= hdmac_resources,
 	.num_resources	= ARRAY_SIZE(hdmac_resources),
@@ -64,7 +59,6 @@ static struct platform_device at_hdmac_device = {
 
 void __init at91_add_device_hdmac(void)
 {
-	dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
 	platform_device_register(&at_hdmac_device);
 }
 #else

arch/arm/mach-at91/generic.h

@@ -58,7 +58,9 @@ extern void at91_irq_suspend(void);
 extern void at91_irq_resume(void);
 
 /* reset */
+extern void at91_ioremap_rstc(u32 base_addr);
 extern void at91sam9_alt_restart(char, const char *);
+extern void at91sam9g45_restart(char, const char *);
 
 /* shutdown */
 extern void at91_ioremap_shdwc(u32 base_addr);

arch/arm/mach-at91/include/mach/at91_rstc.h

@@ -16,13 +16,25 @@
 #ifndef AT91_RSTC_H
 #define AT91_RSTC_H
 
-#define AT91_RSTC_CR		(AT91_RSTC + 0x00)	/* Reset Controller Control Register */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_rstc_base;
+
+#define at91_rstc_read(field) \
+	__raw_readl(at91_rstc_base + field)
+
+#define at91_rstc_write(field, value) \
+	__raw_writel(value, at91_rstc_base + field);
+#else
+.extern at91_rstc_base
+#endif
+
+#define AT91_RSTC_CR		0x00			/* Reset Controller Control Register */
 #define		AT91_RSTC_PROCRST	(1 << 0)		/* Processor Reset */
 #define		AT91_RSTC_PERRST	(1 << 2)		/* Peripheral Reset */
 #define		AT91_RSTC_EXTRST	(1 << 3)		/* External Reset */
 #define		AT91_RSTC_KEY		(0xa5 << 24)		/* KEY Password */
 
-#define AT91_RSTC_SR		(AT91_RSTC + 0x04)	/* Reset Controller Status Register */
+#define AT91_RSTC_SR		0x04			/* Reset Controller Status Register */
 #define		AT91_RSTC_URSTS		(1 << 0)		/* User Reset Status */
 #define		AT91_RSTC_RSTTYP	(7 << 8)		/* Reset Type */
 #define			AT91_RSTC_RSTTYP_GENERAL	(0 << 8)
@@ -33,7 +45,7 @@
 #define		AT91_RSTC_NRSTL		(1 << 16)		/* NRST Pin Level */
 #define		AT91_RSTC_SRCMP		(1 << 17)		/* Software Reset Command in Progress */
 
-#define AT91_RSTC_MR		(AT91_RSTC + 0x08)	/* Reset Controller Mode Register */
+#define AT91_RSTC_MR		0x08			/* Reset Controller Mode Register */
 #define		AT91_RSTC_URSTEN	(1 << 0)		/* User Reset Enable */
 #define		AT91_RSTC_URSTIEN	(1 << 4)		/* User Reset Interrupt Enable */
 #define		AT91_RSTC_ERSTL		(0xf << 8)		/* External Reset Length */

arch/arm/mach-at91/include/mach/at91cap9.h

@@ -83,7 +83,6 @@
 #define AT91_DDRSDRC0	(0xffffe600 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_GPBR	(cpu_is_at91cap9_revB() ?	\
 			(0xfffffd50 - AT91_BASE_SYS) :	\
 			(0xfffffd60 - AT91_BASE_SYS))
@@ -96,6 +95,7 @@
 #define AT91CAP9_BASE_PIOB	0xfffff400
 #define AT91CAP9_BASE_PIOC	0xfffff600
 #define AT91CAP9_BASE_PIOD	0xfffff800
+#define AT91CAP9_BASE_RSTC	0xfffffd00
 #define AT91CAP9_BASE_SHDWC	0xfffffd10
 #define AT91CAP9_BASE_RTT	0xfffffd20
 #define AT91CAP9_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h

@@ -1,108 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h
- *
- *  (C) 2008 Andrew Victor
- *
- * DDR/SDR Controller (DDRSDRC) - System peripherals registers.
- * Based on AT91CAP9 datasheet revision B.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91CAP9_DDRSDR_H
-#define AT91CAP9_DDRSDR_H
-
-#define AT91_DDRSDRC_MR		0x00	/* Mode Register */
-#define		AT91_DDRSDRC_MODE	(0xf << 0)		/* Command Mode */
-#define			AT91_DDRSDRC_MODE_NORMAL		0
-#define			AT91_DDRSDRC_MODE_NOP		1
-#define			AT91_DDRSDRC_MODE_PRECHARGE	2
-#define			AT91_DDRSDRC_MODE_LMR		3
-#define			AT91_DDRSDRC_MODE_REFRESH	4
-#define			AT91_DDRSDRC_MODE_EXT_LMR	5
-#define			AT91_DDRSDRC_MODE_DEEP		6
-
-#define AT91_DDRSDRC_RTR	0x04	/* Refresh Timer Register */
-#define		AT91_DDRSDRC_COUNT	(0xfff << 0)		/* Refresh Timer Counter */
-
-#define AT91_DDRSDRC_CR		0x08	/* Configuration Register */
-#define		AT91_DDRSDRC_NC		(3 << 0)		/* Number of Column Bits */
-#define			AT91_DDRSDRC_NC_SDR8	(0 << 0)
-#define			AT91_DDRSDRC_NC_SDR9	(1 << 0)
-#define			AT91_DDRSDRC_NC_SDR10	(2 << 0)
-#define			AT91_DDRSDRC_NC_SDR11	(3 << 0)
-#define			AT91_DDRSDRC_NC_DDR9	(0 << 0)
-#define			AT91_DDRSDRC_NC_DDR10	(1 << 0)
-#define			AT91_DDRSDRC_NC_DDR11	(2 << 0)
-#define			AT91_DDRSDRC_NC_DDR12	(3 << 0)
-#define		AT91_DDRSDRC_NR		(3 << 2)		/* Number of Row Bits */
-#define			AT91_DDRSDRC_NR_11	(0 << 2)
-#define			AT91_DDRSDRC_NR_12	(1 << 2)
-#define			AT91_DDRSDRC_NR_13	(2 << 2)
-#define		AT91_DDRSDRC_CAS	(7 << 4)		/* CAS Latency */
-#define			AT91_DDRSDRC_CAS_2	(2 << 4)
-#define			AT91_DDRSDRC_CAS_3	(3 << 4)
-#define			AT91_DDRSDRC_CAS_25	(6 << 4)
-#define		AT91_DDRSDRC_DLL	(1 << 7)		/* Reset DLL */
-#define		AT91_DDRSDRC_DICDS	(1 << 8)		/* Output impedance control */
-
-#define AT91_DDRSDRC_T0PR	0x0C	/* Timing 0 Register */
-#define		AT91_DDRSDRC_TRAS	(0xf <<  0)		/* Active to Precharge delay */
-#define		AT91_DDRSDRC_TRCD	(0xf <<  4)		/* Row to Column delay */
-#define		AT91_DDRSDRC_TWR	(0xf <<  8)		/* Write recovery delay */
-#define		AT91_DDRSDRC_TRC	(0xf << 12)		/* Row cycle delay */
-#define		AT91_DDRSDRC_TRP	(0xf << 16)		/* Row precharge delay */
-#define		AT91_DDRSDRC_TRRD	(0xf << 20)		/* Active BankA to BankB */
-#define		AT91_DDRSDRC_TWTR	(1   << 24)		/* Internal Write to Read delay */
-#define		AT91_DDRSDRC_TMRD	(0xf << 28)		/* Load mode to active/refresh delay */
-
-#define AT91_DDRSDRC_T1PR	0x10	/* Timing 1 Register */
-#define		AT91_DDRSDRC_TRFC	(0x1f << 0)		/* Row Cycle Delay */
-#define		AT91_DDRSDRC_TXSNR	(0xff << 8)		/* Exit self-refresh to non-read */
-#define		AT91_DDRSDRC_TXSRD	(0xff << 16)		/* Exit self-refresh to read */
-#define		AT91_DDRSDRC_TXP	(0xf  << 24)		/* Exit power-down delay */
-
-#define AT91_DDRSDRC_LPR	0x18	/* Low Power Register */
-#define		AT91_DDRSDRC_LPCB		(3 << 0)	/* Low-power Configurations */
-#define			AT91_DDRSDRC_LPCB_DISABLE		0
-#define			AT91_DDRSDRC_LPCB_SELF_REFRESH		1
-#define			AT91_DDRSDRC_LPCB_POWER_DOWN		2
-#define			AT91_DDRSDRC_LPCB_DEEP_POWER_DOWN	3
-#define		AT91_DDRSDRC_CLKFR		(1 << 2)	/* Clock Frozen */
-#define		AT91_DDRSDRC_PASR		(7 << 4)	/* Partial Array Self Refresh */
-#define		AT91_DDRSDRC_TCSR		(3 << 8)	/* Temperature Compensated Self Refresh */
-#define		AT91_DDRSDRC_DS			(3 << 10)	/* Drive Strength */
-#define		AT91_DDRSDRC_TIMEOUT		(3 << 12)	/* Time to define when Low Power Mode is enabled */
-#define			AT91_DDRSDRC_TIMEOUT_0_CLK_CYCLES	(0 << 12)
-#define			AT91_DDRSDRC_TIMEOUT_64_CLK_CYCLES	(1 << 12)
-#define			AT91_DDRSDRC_TIMEOUT_128_CLK_CYCLES	(2 << 12)
-
-#define AT91_DDRSDRC_MDR	0x1C	/* Memory Device Register */
-#define		AT91_DDRSDRC_MD		(3 << 0)		/* Memory Device Type */
-#define			AT91_DDRSDRC_MD_SDR		0
-#define			AT91_DDRSDRC_MD_LOW_POWER_SDR	1
-#define			AT91_DDRSDRC_MD_DDR		2
-#define			AT91_DDRSDRC_MD_LOW_POWER_DDR	3
-
-#define AT91_DDRSDRC_DLLR	0x20	/* DLL Information Register */
-#define		AT91_DDRSDRC_MDINC	(1 << 0)		/* Master Delay increment */
-#define		AT91_DDRSDRC_MDDEC	(1 << 1)		/* Master Delay decrement */
-#define		AT91_DDRSDRC_MDOVF	(1 << 2)		/* Master Delay Overflow */
-#define		AT91_DDRSDRC_SDCOVF	(1 << 3)		/* Slave Delay Correction Overflow */
-#define		AT91_DDRSDRC_SDCUDF	(1 << 4)		/* Slave Delay Correction Underflow */
-#define		AT91_DDRSDRC_SDERF	(1 << 5)		/* Slave Delay Correction error */
-#define		AT91_DDRSDRC_MDVAL	(0xff <<  8)		/* Master Delay value */
-#define		AT91_DDRSDRC_SDVAL	(0xff << 16)		/* Slave Delay value */
-#define		AT91_DDRSDRC_SDCVAL	(0xff << 24)		/* Slave Delay Correction value */
-
-/* Register access macros */
-#define at91_ramc_read(num, reg) \
-	at91_sys_read(AT91_DDRSDRC##num + reg)
-#define at91_ramc_write(num, reg, value) \
-	at91_sys_write(AT91_DDRSDRC##num + reg, value)
-
-
-#endif

arch/arm/mach-at91/include/mach/at91sam9260.h

@@ -83,7 +83,6 @@
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
 #define AT91SAM9260_BASE_ECC	0xffffe800
@@ -92,6 +91,7 @@
 #define AT91SAM9260_BASE_PIOA	0xfffff400
 #define AT91SAM9260_BASE_PIOB	0xfffff600
 #define AT91SAM9260_BASE_PIOC	0xfffff800
+#define AT91SAM9260_BASE_RSTC	0xfffffd00
 #define AT91SAM9260_BASE_SHDWC	0xfffffd10
 #define AT91SAM9260_BASE_RTT	0xfffffd20
 #define AT91SAM9260_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/at91sam9261.h

@@ -68,7 +68,6 @@
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
 #define AT91SAM9261_BASE_SMC	0xffffec00
@@ -76,6 +75,7 @@
 #define AT91SAM9261_BASE_PIOA	0xfffff400
 #define AT91SAM9261_BASE_PIOB	0xfffff600
 #define AT91SAM9261_BASE_PIOC	0xfffff800
+#define AT91SAM9261_BASE_RSTC	0xfffffd00
 #define AT91SAM9261_BASE_SHDWC	0xfffffd10
 #define AT91SAM9261_BASE_RTT	0xfffffd20
 #define AT91SAM9261_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/at91sam9263.h

@@ -78,7 +78,6 @@
 #define AT91_SDRAMC1	(0xffffe800 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 
 #define AT91SAM9263_BASE_ECC0	0xffffe000
@@ -91,6 +90,7 @@
 #define AT91SAM9263_BASE_PIOC	0xfffff600
 #define AT91SAM9263_BASE_PIOD	0xfffff800
 #define AT91SAM9263_BASE_PIOE	0xfffffa00
+#define AT91SAM9263_BASE_RSTC	0xfffffd00
 #define AT91SAM9263_BASE_SHDWC	0xfffffd10
 #define AT91SAM9263_BASE_RTT0	0xfffffd20
 #define AT91SAM9263_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/at91sam9_ddrsdr.h

@@ -46,10 +46,10 @@
 #define			AT91_DDRSDRC_CAS_25	(6 << 4)
 #define		AT91_DDRSDRC_RST_DLL	(1 << 7)		/* Reset DLL */
 #define		AT91_DDRSDRC_DICDS	(1 << 8)		/* Output impedance control */
-#define		AT91_DDRSDRC_DIS_DLL	(1 << 9)		/* Disable DLL */
-#define		AT91_DDRSDRC_OCD	(1 << 12)		/* Off-Chip Driver */
-#define		AT91_DDRSDRC_DQMS	(1 << 16)		/* Mask Data is Shared */
-#define		AT91_DDRSDRC_ACTBST	(1 << 18)		/* Active Bank X to Burst Stop Read Access Bank Y */
+#define		AT91_DDRSDRC_DIS_DLL	(1 << 9)		/* Disable DLL [SAM9 Only] */
+#define		AT91_DDRSDRC_OCD	(1 << 12)		/* Off-Chip Driver [SAM9 Only] */
+#define		AT91_DDRSDRC_DQMS	(1 << 16)		/* Mask Data is Shared [SAM9 Only] */
+#define		AT91_DDRSDRC_ACTBST	(1 << 18)		/* Active Bank X to Burst Stop Read Access Bank Y [SAM9 Only] */
 
 #define AT91_DDRSDRC_T0PR	0x0C	/* Timing 0 Register */
 #define		AT91_DDRSDRC_TRAS	(0xf <<  0)		/* Active to Precharge delay */
@@ -59,7 +59,8 @@
 #define		AT91_DDRSDRC_TRP	(0xf << 16)		/* Row precharge delay */
 #define		AT91_DDRSDRC_TRRD	(0xf << 20)		/* Active BankA to BankB */
 #define		AT91_DDRSDRC_TWTR	(0x7 << 24)		/* Internal Write to Read delay */
-#define		AT91_DDRSDRC_RED_WRRD	(0x1 << 27)		/* Reduce Write to Read Delay */
+#define		AT91CAP9_DDRSDRC_TWTR	(1   << 24)		/* Internal Write to Read delay */
+#define		AT91_DDRSDRC_RED_WRRD	(0x1 << 27)		/* Reduce Write to Read Delay [SAM9 Only] */
 #define		AT91_DDRSDRC_TMRD	(0xf << 28)		/* Load mode to active/refresh delay */
 
 #define AT91_DDRSDRC_T1PR	0x10	/* Timing 1 Register */
@@ -68,13 +69,14 @@
 #define		AT91_DDRSDRC_TXSRD	(0xff << 16)		/* Exit self-refresh to read */
 #define		AT91_DDRSDRC_TXP	(0xf  << 24)		/* Exit power-down delay */
 
-#define AT91_DDRSDRC_T2PR	0x14	/* Timing 2 Register */
+#define AT91_DDRSDRC_T2PR	0x14	/* Timing 2 Register [SAM9 Only] */
 #define		AT91_DDRSDRC_TXARD	(0xf  << 0)		/* Exit active power down delay to read command in mode "Fast Exit" */
 #define		AT91_DDRSDRC_TXARDS	(0xf  << 4)		/* Exit active power down delay to read command in mode "Slow Exit" */
 #define		AT91_DDRSDRC_TRPA	(0xf  << 8)		/* Row Precharge All delay */
 #define		AT91_DDRSDRC_TRTP	(0x7  << 12)		/* Read to Precharge delay */
 
 #define AT91_DDRSDRC_LPR	0x1C	/* Low Power Register */
+#define AT91CAP9_DDRSDRC_LPR	0x18	/* Low Power Register */
 #define		AT91_DDRSDRC_LPCB	(3 << 0)		/* Low-power Configurations */
 #define			AT91_DDRSDRC_LPCB_DISABLE		0
 #define			AT91_DDRSDRC_LPCB_SELF_REFRESH		1
@@ -92,32 +94,40 @@
 #define		AT91_DDRSDRC_UPD_MR	(3 << 20)	 /* Update load mode register and extended mode register */
 
 #define AT91_DDRSDRC_MDR	0x20	/* Memory Device Register */
+#define AT91CAP9_DDRSDRC_MDR	0x1C	/* Memory Device Register */
 #define		AT91_DDRSDRC_MD		(3 << 0)		/* Memory Device Type */
 #define			AT91_DDRSDRC_MD_SDR		0
 #define			AT91_DDRSDRC_MD_LOW_POWER_SDR	1
+#define			AT91CAP9_DDRSDRC_MD_DDR		2
 #define			AT91_DDRSDRC_MD_LOW_POWER_DDR	3
-#define			AT91_DDRSDRC_MD_DDR2		6
+#define			AT91_DDRSDRC_MD_DDR2		6	/* [SAM9 Only] */
 #define		AT91_DDRSDRC_DBW	(1 << 4)		/* Data Bus Width */
 #define			AT91_DDRSDRC_DBW_32BITS		(0 <<  4)
 #define			AT91_DDRSDRC_DBW_16BITS		(1 <<  4)
 
 #define AT91_DDRSDRC_DLL	0x24	/* DLL Information Register */
+#define AT91CAP9_DDRSDRC_DLL	0x20	/* DLL Information Register */
 #define		AT91_DDRSDRC_MDINC	(1 << 0)		/* Master Delay increment */
 #define		AT91_DDRSDRC_MDDEC	(1 << 1)		/* Master Delay decrement */
 #define		AT91_DDRSDRC_MDOVF	(1 << 2)		/* Master Delay Overflow */
+#define		AT91CAP9_DDRSDRC_SDCOVF	(1 << 3)		/* Slave Delay Correction Overflow */
+#define		AT91CAP9_DDRSDRC_SDCUDF	(1 << 4)		/* Slave Delay Correction Underflow */
+#define		AT91CAP9_DDRSDRC_SDERF	(1 << 5)		/* Slave Delay Correction error */
 #define		AT91_DDRSDRC_MDVAL	(0xff <<  8)		/* Master Delay value */
+#define		AT91CAP9_DDRSDRC_SDVAL	(0xff << 16)		/* Slave Delay value */
+#define		AT91CAP9_DDRSDRC_SDCVAL	(0xff << 24)		/* Slave Delay Correction value */
 
-#define AT91_DDRSDRC_HS		0x2C	/* High Speed Register */
+#define AT91_DDRSDRC_HS		0x2C	/* High Speed Register [SAM9 Only] */
 #define		AT91_DDRSDRC_DIS_ATCP_RD	(1 << 2)	/* Anticip read access is disabled */
 
 #define AT91_DDRSDRC_DELAY(n)	(0x30 + (0x4 * (n)))	/* Delay I/O Register n */
 
-#define AT91_DDRSDRC_WPMR	0xE4	/* Write Protect Mode Register */
+#define AT91_DDRSDRC_WPMR	0xE4	/* Write Protect Mode Register [SAM9 Only] */
 #define		AT91_DDRSDRC_WP		(1 << 0)		/* Write protect enable */
 #define		AT91_DDRSDRC_WPKEY	(0xffffff << 8)		/* Write protect key */
 #define		AT91_DDRSDRC_KEY	(0x444452 << 8)		/* Write protect key = "DDR" */
 
-#define AT91_DDRSDRC_WPSR	0xE8	/* Write Protect Status Register */
+#define AT91_DDRSDRC_WPSR	0xE8	/* Write Protect Status Register [SAM9 Only] */
 #define		AT91_DDRSDRC_WPVS	(1 << 0)		/* Write protect violation status */
 #define		AT91_DDRSDRC_WPVSRC	(0xffff << 8)		/* Write protect violation source */
 

arch/arm/mach-at91/include/mach/at91sam9_smc.h

@@ -18,6 +18,35 @@
 
 #include <mach/cpu.h>
 
+#ifndef __ASSEMBLY__
+struct sam9_smc_config {
+	/* Setup register */
+	u8 ncs_read_setup;
+	u8 nrd_setup;
+	u8 ncs_write_setup;
+	u8 nwe_setup;
+
+	/* Pulse register */
+	u8 ncs_read_pulse;
+	u8 nrd_pulse;
+	u8 ncs_write_pulse;
+	u8 nwe_pulse;
+
+	/* Cycle register */
+	u16 read_cycle;
+	u16 write_cycle;
+
+	/* Mode register */
+	u32 mode;
+	u8 tdf_cycles:4;
+};
+
+extern void sam9_smc_configure(int id, int cs, struct sam9_smc_config *config);
+extern void sam9_smc_read(int id, int cs, struct sam9_smc_config *config);
+extern void sam9_smc_read_mode(int id, int cs, struct sam9_smc_config *config);
+extern void sam9_smc_write_mode(int id, int cs, struct sam9_smc_config *config);
+#endif
+
 #define AT91_SMC_SETUP		0x00				/* Setup Register for CS n */
 #define		AT91_SMC_NWESETUP	(0x3f << 0)			/* NWE Setup Length */
 #define			AT91_SMC_NWESETUP_(x)	((x) << 0)

arch/arm/mach-at91/include/mach/at91sam9g45.h

@@ -90,7 +90,6 @@
 #define AT91_DDRSDRC0	(0xffffe600 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 
 #define AT91SAM9G45_BASE_ECC	0xffffe200
@@ -102,6 +101,7 @@
 #define AT91SAM9G45_BASE_PIOC	0xfffff600
 #define AT91SAM9G45_BASE_PIOD	0xfffff800
 #define AT91SAM9G45_BASE_PIOE	0xfffffa00
+#define AT91SAM9G45_BASE_RSTC	0xfffffd00
 #define AT91SAM9G45_BASE_SHDWC	0xfffffd10
 #define AT91SAM9G45_BASE_RTT	0xfffffd20
 #define AT91SAM9G45_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/at91sam9rl.h

@@ -72,7 +72,6 @@
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
-#define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
 #define AT91_SCKCR	(0xfffffd50 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 
@@ -84,6 +83,7 @@
 #define AT91SAM9RL_BASE_PIOB	0xfffff600
 #define AT91SAM9RL_BASE_PIOC	0xfffff800
 #define AT91SAM9RL_BASE_PIOD	0xfffffa00
+#define AT91SAM9RL_BASE_RSTC	0xfffffd00
 #define AT91SAM9RL_BASE_SHDWC	0xfffffd10
 #define AT91SAM9RL_BASE_RTT	0xfffffd20
 #define AT91SAM9RL_BASE_PIT	0xfffffd30

arch/arm/mach-at91/include/mach/board.h

@@ -88,7 +88,7 @@ extern void __init at91_add_device_eth(struct macb_platform_data *data);
 struct at91_usbh_data {
 	u8		ports;		/* number of ports on root hub */
 	int		vbus_pin[2];	/* port power-control pin */
-	u8              vbus_pin_inverted;
+	u8              vbus_pin_active_low[2];
 	u8              overcurrent_supported;
 	int             overcurrent_pin[2];
 	u8              overcurrent_status[2];

arch/arm/mach-at91/pm.c

@@ -34,7 +34,6 @@
 /*
  * Show the reason for the previous system reset.
  */
-#if defined(AT91_RSTC)
 
 #include <mach/at91_rstc.h>
 #include <mach/at91_shdwc.h>
@@ -58,10 +57,10 @@ static void __init show_reset_status(void)
 	char *reason, *r2 = reset;
 	u32 reset_type, wake_type;
 
-	if (!at91_shdwc_base)
+	if (!at91_shdwc_base || !at91_rstc_base)
 		return;
 
-	reset_type = at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP;
+	reset_type = at91_rstc_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP;
 	wake_type = at91_shdwc_read(AT91_SHDW_SR);
 
 	switch (reset_type) {
@@ -102,10 +101,6 @@ static void __init show_reset_status(void)
 	}
 	pr_info("AT91: Starting after %s %s\n", reason, r2);
 }
-#else
-static void __init show_reset_status(void) {}
-#endif
-
 
 static int at91_pm_valid_state(suspend_state_t state)
 {

arch/arm/mach-at91/pm.h

@@ -25,21 +25,21 @@ static inline u32 sdram_selfrefresh_enable(void)
 								: : "r" (0))
 
 #elif defined(CONFIG_ARCH_AT91CAP9)
-#include <mach/at91cap9_ddrsdr.h>
+#include <mach/at91sam9_ddrsdr.h>
 
 
 static inline u32 sdram_selfrefresh_enable(void)
 {
 	u32 saved_lpr, lpr;
 
-	saved_lpr = at91_ramc_read(0, AT91_DDRSDRC_LPR);
+	saved_lpr = at91_ramc_read(0, AT91CAP9_DDRSDRC_LPR);
 
 	lpr = saved_lpr & ~AT91_DDRSDRC_LPCB;
-	at91_ramc_write(0, AT91_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH);
+	at91_ramc_write(0, AT91CAP9_DDRSDRC_LPR, lpr | AT91_DDRSDRC_LPCB_SELF_REFRESH);
 	return saved_lpr;
 }
 
-#define sdram_selfrefresh_disable(saved_lpr)	at91_ramc_write(0, AT91_DDRSDRC_LPR, saved_lpr)
+#define sdram_selfrefresh_disable(saved_lpr)	at91_ramc_write(0, AT91CAP9_DDRSDRC_LPR, saved_lpr)
 #define wait_for_interrupt_enable()		cpu_do_idle()
 
 #elif defined(CONFIG_ARCH_AT91SAM9G45)

arch/arm/mach-at91/pm_slowclock.S

@@ -18,9 +18,8 @@
 
 #if defined(CONFIG_ARCH_AT91RM9200)
 #include <mach/at91rm9200_mc.h>
-#elif defined(CONFIG_ARCH_AT91CAP9)
-#include <mach/at91cap9_ddrsdr.h>
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
+#elif defined(CONFIG_ARCH_AT91CAP9) \
+	|| defined(CONFIG_ARCH_AT91SAM9G45)
 #include <mach/at91sam9_ddrsdr.h>
 #else
 #include <mach/at91sam9_sdramc.h>

arch/arm/mach-at91/sam9_smc.c

@@ -2,6 +2,7 @@
  * linux/arch/arm/mach-at91/sam9_smc.c
  *
  * Copyright (C) 2008 Andrew Victor
+ * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -22,7 +23,22 @@
 
 static void __iomem *smc_base_addr[2];
 
-static void __init sam9_smc_cs_configure(void __iomem *base, struct sam9_smc_config* config)
+static void sam9_smc_cs_write_mode(void __iomem *base,
+					struct sam9_smc_config *config)
+{
+	__raw_writel(config->mode
+		   | AT91_SMC_TDF_(config->tdf_cycles),
+		   base + AT91_SMC_MODE);
+}
+
+void sam9_smc_write_mode(int id, int cs,
+					struct sam9_smc_config *config)
+{
+	sam9_smc_cs_write_mode(AT91_SMC_CS(id, cs), config);
+}
+
+static void sam9_smc_cs_configure(void __iomem *base,
+					struct sam9_smc_config *config)
 {
 
 	/* Setup register */
@@ -45,16 +61,66 @@ static void __init sam9_smc_cs_configure(void __iomem *base, struct sam9_smc_con
 		   base + AT91_SMC_CYCLE);
 
 	/* Mode register */
-	__raw_writel(config->mode
-		   | AT91_SMC_TDF_(config->tdf_cycles),
-		   base + AT91_SMC_MODE);
+	sam9_smc_cs_write_mode(base, config);
 }
 
-void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config)
+void sam9_smc_configure(int id, int cs,
+					struct sam9_smc_config *config)
 {
 	sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config);
 }
 
+static void sam9_smc_cs_read_mode(void __iomem *base,
+					struct sam9_smc_config *config)
+{
+	u32 val = __raw_readl(base + AT91_SMC_MODE);
+
+	config->mode = (val & ~AT91_SMC_NWECYCLE);
+	config->tdf_cycles = (val & AT91_SMC_NWECYCLE) >> 16 ;
+}
+
+void sam9_smc_read_mode(int id, int cs,
+					struct sam9_smc_config *config)
+{
+	sam9_smc_cs_read_mode(AT91_SMC_CS(id, cs), config);
+}
+
+static void sam9_smc_cs_read(void __iomem *base,
+					struct sam9_smc_config *config)
+{
+	u32 val;
+
+	/* Setup register */
+	val = __raw_readl(base + AT91_SMC_SETUP);
+
+	config->nwe_setup = val & AT91_SMC_NWESETUP;
+	config->ncs_write_setup = (val & AT91_SMC_NCS_WRSETUP) >> 8;
+	config->nrd_setup = (val & AT91_SMC_NRDSETUP) >> 16;
+	config->ncs_read_setup = (val & AT91_SMC_NCS_RDSETUP) >> 24;
+
+	/* Pulse register */
+	val = __raw_readl(base + AT91_SMC_PULSE);
+
+	config->nwe_setup = val & AT91_SMC_NWEPULSE;
+	config->ncs_write_pulse = (val & AT91_SMC_NCS_WRPULSE) >> 8;
+	config->nrd_pulse = (val & AT91_SMC_NRDPULSE) >> 16;
+	config->ncs_read_pulse = (val & AT91_SMC_NCS_RDPULSE) >> 24;
+
+	/* Cycle register */
+	val = __raw_readl(base + AT91_SMC_CYCLE);
+
+	config->write_cycle = val & AT91_SMC_NWECYCLE;
+	config->read_cycle = (val & AT91_SMC_NRDCYCLE) >> 16;
+
+	/* Mode register */
+	sam9_smc_cs_read_mode(base, config);
+}
+
+void sam9_smc_read(int id, int cs, struct sam9_smc_config *config)
+{
+	sam9_smc_cs_read(AT91_SMC_CS(id, cs), config);
+}
+
 void __init at91sam9_ioremap_smc(int id, u32 addr)
 {
 	if (id > 1) {

arch/arm/mach-at91/sam9_smc.h

@@ -8,27 +8,4 @@
  * published by the Free Software Foundation.
  */
 
-struct sam9_smc_config {
-	/* Setup register */
-	u8 ncs_read_setup;
-	u8 nrd_setup;
-	u8 ncs_write_setup;
-	u8 nwe_setup;
-
-	/* Pulse register */
-	u8 ncs_read_pulse;
-	u8 nrd_pulse;
-	u8 ncs_write_pulse;
-	u8 nwe_pulse;
-
-	/* Cycle register */
-	u16 read_cycle;
-	u16 write_cycle;
-
-	/* Mode register */
-	u32 mode;
-	u8 tdf_cycles:4;
-};
-
-extern void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config);
 extern void __init at91sam9_ioremap_smc(int id, u32 addr);

arch/arm/mach-at91/setup.c

@@ -29,9 +29,12 @@ EXPORT_SYMBOL(at91_soc_initdata);
 void __init at91rm9200_set_type(int type)
 {
 	if (type == ARCH_REVISON_9200_PQFP)
-		at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
-	else
 		at91_soc_initdata.subtype = AT91_SOC_RM9200_PQFP;
+	else
+		at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
+
+	pr_info("AT91: filled in soc subtype: %s\n",
+		at91_get_soc_subtype(&at91_soc_initdata));
 }
 
 void __init at91_init_irq_default(void)
@@ -281,6 +284,15 @@ void __init at91_ioremap_shdwc(u32 base_addr)
 	pm_power_off = at91sam9_poweroff;
 }
 
+void __iomem *at91_rstc_base;
+
+void __init at91_ioremap_rstc(u32 base_addr)
+{
+	at91_rstc_base = ioremap(base_addr, 16);
+	if (!at91_rstc_base)
+		panic("Impossible to ioremap at91_rstc_base\n");
+}
+
 void __init at91_initialize(unsigned long main_clock)
 {
 	at91_boot_soc.ioremap_registers();

arch/arm/mach-bcmring/arch.c

@@ -194,6 +194,6 @@ MACHINE_START(BCMRING, "BCMRING")
 	.init_early = bcmring_init_early,
 	.init_irq = bcmring_init_irq,
 	.timer = &bcmring_timer,
-	.init_machine = bcmring_init_machine
+	.init_machine = bcmring_init_machine,
 	.restart = bcmring_restart,
 MACHINE_END

arch/arm/mach-bcmring/dma.c

@@ -33,17 +33,11 @@
 
 #include <mach/timer.h>
 
-#include <linux/mm.h>
 #include <linux/pfn.h>
 #include <linux/atomic.h>
 #include <linux/sched.h>
 #include <mach/dma.h>
 
-/* I don't quite understand why dc4 fails when this is set to 1 and DMA is enabled */
-/* especially since dc4 doesn't use kmalloc'd memory. */
-
-#define ALLOW_MAP_OF_KMALLOC_MEMORY 0
-
 /* ---- Public Variables ------------------------------------------------- */
 
 /* ---- Private Constants and Types -------------------------------------- */
@@ -53,58 +47,18 @@
 #define CONTROLLER_FROM_HANDLE(handle)    (((handle) >> 4) & 0x0f)
 #define CHANNEL_FROM_HANDLE(handle)       ((handle) & 0x0f)
 
-#define DMA_MAP_DEBUG   0
-
-#if DMA_MAP_DEBUG
-#   define  DMA_MAP_PRINT(fmt, args...)   printk("%s: " fmt, __func__,  ## args)
-#else
-#   define  DMA_MAP_PRINT(fmt, args...)
-#endif
 
 /* ---- Private Variables ------------------------------------------------ */
 
 static DMA_Global_t gDMA;
 static struct proc_dir_entry *gDmaDir;
 
-static atomic_t gDmaStatMemTypeKmalloc = ATOMIC_INIT(0);
-static atomic_t gDmaStatMemTypeVmalloc = ATOMIC_INIT(0);
-static atomic_t gDmaStatMemTypeUser = ATOMIC_INIT(0);
-static atomic_t gDmaStatMemTypeCoherent = ATOMIC_INIT(0);
-
 #include "dma_device.c"
 
 /* ---- Private Function Prototypes -------------------------------------- */
 
 /* ---- Functions  ------------------------------------------------------- */
 
-/****************************************************************************/
-/**
-*   Displays information for /proc/dma/mem-type
-*/
-/****************************************************************************/
-
-static int dma_proc_read_mem_type(char *buf, char **start, off_t offset,
-				  int count, int *eof, void *data)
-{
-	int len = 0;
-
-	len += sprintf(buf + len, "dma_map_mem statistics\n");
-	len +=
-	    sprintf(buf + len, "coherent: %d\n",
-		    atomic_read(&gDmaStatMemTypeCoherent));
-	len +=
-	    sprintf(buf + len, "kmalloc:  %d\n",
-		    atomic_read(&gDmaStatMemTypeKmalloc));
-	len +=
-	    sprintf(buf + len, "vmalloc:  %d\n",
-		    atomic_read(&gDmaStatMemTypeVmalloc));
-	len +=
-	    sprintf(buf + len, "user:     %d\n",
-		    atomic_read(&gDmaStatMemTypeUser));
-
-	return len;
-}
-
 /****************************************************************************/
 /**
 *   Displays information for /proc/dma/channels
@@ -846,8 +800,6 @@ int dma_init(void)
 				       dma_proc_read_channels, NULL);
 		create_proc_read_entry("devices", 0, gDmaDir,
 				       dma_proc_read_devices, NULL);
-		create_proc_read_entry("mem-type", 0, gDmaDir,
-				       dma_proc_read_mem_type, NULL);
 	}
 
 out:
@@ -1565,767 +1517,3 @@ int dma_set_device_handler(DMA_Device_t dev,	/* Device to set the callback for.
 }
 
 EXPORT_SYMBOL(dma_set_device_handler);
-
-/****************************************************************************/
-/**
-*   Initializes a memory mapping structure
-*/
-/****************************************************************************/
-
-int dma_init_mem_map(DMA_MemMap_t *memMap)
-{
-	memset(memMap, 0, sizeof(*memMap));
-
-	sema_init(&memMap->lock, 1);
-
-	return 0;
-}
-
-EXPORT_SYMBOL(dma_init_mem_map);
-
-/****************************************************************************/
-/**
-*   Releases any memory currently being held by a memory mapping structure.
-*/
-/****************************************************************************/
-
-int dma_term_mem_map(DMA_MemMap_t *memMap)
-{
-	down(&memMap->lock);	/* Just being paranoid */
-
-	/* Free up any allocated memory */
-
-	up(&memMap->lock);
-	memset(memMap, 0, sizeof(*memMap));
-
-	return 0;
-}
-
-EXPORT_SYMBOL(dma_term_mem_map);
-
-/****************************************************************************/
-/**
-*   Looks at a memory address and categorizes it.
-*
-*   @return One of the values from the DMA_MemType_t enumeration.
-*/
-/****************************************************************************/
-
-DMA_MemType_t dma_mem_type(void *addr)
-{
-	unsigned long addrVal = (unsigned long)addr;
-
-	if (addrVal >= CONSISTENT_BASE) {
-		/* NOTE: DMA virtual memory space starts at 0xFFxxxxxx */
-
-		/* dma_alloc_xxx pages are physically and virtually contiguous */
-
-		return DMA_MEM_TYPE_DMA;
-	}
-
-	/* Technically, we could add one more classification. Addresses between VMALLOC_END */
-	/* and the beginning of the DMA virtual address could be considered to be I/O space. */
-	/* Right now, nobody cares about this particular classification, so we ignore it. */
-
-	if (is_vmalloc_addr(addr)) {
-		/* Address comes from the vmalloc'd region. Pages are virtually */
-		/* contiguous but NOT physically contiguous */
-
-		return DMA_MEM_TYPE_VMALLOC;
-	}
-
-	if (addrVal >= PAGE_OFFSET) {
-		/* PAGE_OFFSET is typically 0xC0000000 */
-
-		/* kmalloc'd pages are physically contiguous */
-
-		return DMA_MEM_TYPE_KMALLOC;
-	}
-
-	return DMA_MEM_TYPE_USER;
-}
-
-EXPORT_SYMBOL(dma_mem_type);
-
-/****************************************************************************/
-/**
-*   Looks at a memory address and determines if we support DMA'ing to/from
-*   that type of memory.
-*
-*   @return boolean -
-*               return value != 0 means dma supported
-*               return value == 0 means dma not supported
-*/
-/****************************************************************************/
-
-int dma_mem_supports_dma(void *addr)
-{
-	DMA_MemType_t memType = dma_mem_type(addr);
-
-	return (memType == DMA_MEM_TYPE_DMA)
-#if ALLOW_MAP_OF_KMALLOC_MEMORY
-	    || (memType == DMA_MEM_TYPE_KMALLOC)
-#endif
-	    || (memType == DMA_MEM_TYPE_USER);
-}
-
-EXPORT_SYMBOL(dma_mem_supports_dma);
-
-/****************************************************************************/
-/**
-*   Maps in a memory region such that it can be used for performing a DMA.
-*
-*   @return
-*/
-/****************************************************************************/
-
-int dma_map_start(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		  enum dma_data_direction dir	/* Direction that the mapping will be going */
-    ) {
-	int rc;
-
-	down(&memMap->lock);
-
-	DMA_MAP_PRINT("memMap: %p\n", memMap);
-
-	if (memMap->inUse) {
-		printk(KERN_ERR "%s: memory map %p is already being used\n",
-		       __func__, memMap);
-		rc = -EBUSY;
-		goto out;
-	}
-
-	memMap->inUse = 1;
-	memMap->dir = dir;
-	memMap->numRegionsUsed = 0;
-
-	rc = 0;
-
-out:
-
-	DMA_MAP_PRINT("returning %d", rc);
-
-	up(&memMap->lock);
-
-	return rc;
-}
-
-EXPORT_SYMBOL(dma_map_start);
-
-/****************************************************************************/
-/**
-*   Adds a segment of memory to a memory map. Each segment is both
-*   physically and virtually contiguous.
-*
-*   @return     0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-static int dma_map_add_segment(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-			       DMA_Region_t *region,	/* Region that the segment belongs to */
-			       void *virtAddr,	/* Virtual address of the segment being added */
-			       dma_addr_t physAddr,	/* Physical address of the segment being added */
-			       size_t numBytes	/* Number of bytes of the segment being added */
-    ) {
-	DMA_Segment_t *segment;
-
-	DMA_MAP_PRINT("memMap:%p va:%p pa:0x%x #:%d\n", memMap, virtAddr,
-		      physAddr, numBytes);
-
-	/* Sanity check */
-
-	if (((unsigned long)virtAddr < (unsigned long)region->virtAddr)
-	    || (((unsigned long)virtAddr + numBytes)) >
-	    ((unsigned long)region->virtAddr + region->numBytes)) {
-		printk(KERN_ERR
-		       "%s: virtAddr %p is outside region @ %p len: %d\n",
-		       __func__, virtAddr, region->virtAddr, region->numBytes);
-		return -EINVAL;
-	}
-
-	if (region->numSegmentsUsed > 0) {
-		/* Check to see if this segment is physically contiguous with the previous one */
-
-		segment = &region->segment[region->numSegmentsUsed - 1];
-
-		if ((segment->physAddr + segment->numBytes) == physAddr) {
-			/* It is - just add on to the end */
-
-			DMA_MAP_PRINT("appending %d bytes to last segment\n",
-				      numBytes);
-
-			segment->numBytes += numBytes;
-
-			return 0;
-		}
-	}
-
-	/* Reallocate to hold more segments, if required. */
-
-	if (region->numSegmentsUsed >= region->numSegmentsAllocated) {
-		DMA_Segment_t *newSegment;
-		size_t oldSize =
-		    region->numSegmentsAllocated * sizeof(*newSegment);
-		int newAlloc = region->numSegmentsAllocated + 4;
-		size_t newSize = newAlloc * sizeof(*newSegment);
-
-		newSegment = kmalloc(newSize, GFP_KERNEL);
-		if (newSegment == NULL) {
-			return -ENOMEM;
-		}
-		memcpy(newSegment, region->segment, oldSize);
-		memset(&((uint8_t *) newSegment)[oldSize], 0,
-		       newSize - oldSize);
-		kfree(region->segment);
-
-		region->numSegmentsAllocated = newAlloc;
-		region->segment = newSegment;
-	}
-
-	segment = &region->segment[region->numSegmentsUsed];
-	region->numSegmentsUsed++;
-
-	segment->virtAddr = virtAddr;
-	segment->physAddr = physAddr;
-	segment->numBytes = numBytes;
-
-	DMA_MAP_PRINT("returning success\n");
-
-	return 0;
-}
-
-/****************************************************************************/
-/**
-*   Adds a region of memory to a memory map. Each region is virtually
-*   contiguous, but not necessarily physically contiguous.
-*
-*   @return     0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-int dma_map_add_region(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		       void *mem,	/* Virtual address that we want to get a map of */
-		       size_t numBytes	/* Number of bytes being mapped */
-    ) {
-	unsigned long addr = (unsigned long)mem;
-	unsigned int offset;
-	int rc = 0;
-	DMA_Region_t *region;
-	dma_addr_t physAddr;
-
-	down(&memMap->lock);
-
-	DMA_MAP_PRINT("memMap:%p va:%p #:%d\n", memMap, mem, numBytes);
-
-	if (!memMap->inUse) {
-		printk(KERN_ERR "%s: Make sure you call dma_map_start first\n",
-		       __func__);
-		rc = -EINVAL;
-		goto out;
-	}
-
-	/* Reallocate to hold more regions. */
-
-	if (memMap->numRegionsUsed >= memMap->numRegionsAllocated) {
-		DMA_Region_t *newRegion;
-		size_t oldSize =
-		    memMap->numRegionsAllocated * sizeof(*newRegion);
-		int newAlloc = memMap->numRegionsAllocated + 4;
-		size_t newSize = newAlloc * sizeof(*newRegion);
-
-		newRegion = kmalloc(newSize, GFP_KERNEL);
-		if (newRegion == NULL) {
-			rc = -ENOMEM;
-			goto out;
-		}
-		memcpy(newRegion, memMap->region, oldSize);
-		memset(&((uint8_t *) newRegion)[oldSize], 0, newSize - oldSize);
-
-		kfree(memMap->region);
-
-		memMap->numRegionsAllocated = newAlloc;
-		memMap->region = newRegion;
-	}
-
-	region = &memMap->region[memMap->numRegionsUsed];
-	memMap->numRegionsUsed++;
-
-	offset = addr & ~PAGE_MASK;
-
-	region->memType = dma_mem_type(mem);
-	region->virtAddr = mem;
-	region->numBytes = numBytes;
-	region->numSegmentsUsed = 0;
-	region->numLockedPages = 0;
-	region->lockedPages = NULL;
-
-	switch (region->memType) {
-	case DMA_MEM_TYPE_VMALLOC:
-		{
-			atomic_inc(&gDmaStatMemTypeVmalloc);
-
-			/* printk(KERN_ERR "%s: vmalloc'd pages are not supported\n", __func__); */
-
-			/* vmalloc'd pages are not physically contiguous */
-
-			rc = -EINVAL;
-			break;
-		}
-
-	case DMA_MEM_TYPE_KMALLOC:
-		{
-			atomic_inc(&gDmaStatMemTypeKmalloc);
-
-			/* kmalloc'd pages are physically contiguous, so they'll have exactly */
-			/* one segment */
-
-#if ALLOW_MAP_OF_KMALLOC_MEMORY
-			physAddr =
-			    dma_map_single(NULL, mem, numBytes, memMap->dir);
-			rc = dma_map_add_segment(memMap, region, mem, physAddr,
-						 numBytes);
-#else
-			rc = -EINVAL;
-#endif
-			break;
-		}
-
-	case DMA_MEM_TYPE_DMA:
-		{
-			/* dma_alloc_xxx pages are physically contiguous */
-
-			atomic_inc(&gDmaStatMemTypeCoherent);
-
-			physAddr = (vmalloc_to_pfn(mem) << PAGE_SHIFT) + offset;
-
-			dma_sync_single_for_cpu(NULL, physAddr, numBytes,
-						memMap->dir);
-			rc = dma_map_add_segment(memMap, region, mem, physAddr,
-						 numBytes);
-			break;
-		}
-
-	case DMA_MEM_TYPE_USER:
-		{
-			size_t firstPageOffset;
-			size_t firstPageSize;
-			struct page **pages;
-			struct task_struct *userTask;
-
-			atomic_inc(&gDmaStatMemTypeUser);
-
-#if 1
-			/* If the pages are user pages, then the dma_mem_map_set_user_task function */
-			/* must have been previously called. */
-
-			if (memMap->userTask == NULL) {
-				printk(KERN_ERR
-				       "%s: must call dma_mem_map_set_user_task when using user-mode memory\n",
-				       __func__);
-				return -EINVAL;
-			}
-
-			/* User pages need to be locked. */
-
-			firstPageOffset =
-			    (unsigned long)region->virtAddr & (PAGE_SIZE - 1);
-			firstPageSize = PAGE_SIZE - firstPageOffset;
-
-			region->numLockedPages = (firstPageOffset
-						  + region->numBytes +
-						  PAGE_SIZE - 1) / PAGE_SIZE;
-			pages =
-			    kmalloc(region->numLockedPages *
-				    sizeof(struct page *), GFP_KERNEL);
-
-			if (pages == NULL) {
-				region->numLockedPages = 0;
-				return -ENOMEM;
-			}
-
-			userTask = memMap->userTask;
-
-			down_read(&userTask->mm->mmap_sem);
-			rc = get_user_pages(userTask,	/* task */
-					    userTask->mm,	/* mm */
-					    (unsigned long)region->virtAddr,	/* start */
-					    region->numLockedPages,	/* len */
-					    memMap->dir == DMA_FROM_DEVICE,	/* write */
-					    0,	/* force */
-					    pages,	/* pages (array of pointers to page) */
-					    NULL);	/* vmas */
-			up_read(&userTask->mm->mmap_sem);
-
-			if (rc != region->numLockedPages) {
-				kfree(pages);
-				region->numLockedPages = 0;
-
-				if (rc >= 0) {
-					rc = -EINVAL;
-				}
-			} else {
-				uint8_t *virtAddr = region->virtAddr;
-				size_t bytesRemaining;
-				int pageIdx;
-
-				rc = 0;	/* Since get_user_pages returns +ve number */
-
-				region->lockedPages = pages;
-
-				/* We've locked the user pages. Now we need to walk them and figure */
-				/* out the physical addresses. */
-
-				/* The first page may be partial */
-
-				dma_map_add_segment(memMap,
-						    region,
-						    virtAddr,
-						    PFN_PHYS(page_to_pfn
-							     (pages[0])) +
-						    firstPageOffset,
-						    firstPageSize);
-
-				virtAddr += firstPageSize;
-				bytesRemaining =
-				    region->numBytes - firstPageSize;
-
-				for (pageIdx = 1;
-				     pageIdx < region->numLockedPages;
-				     pageIdx++) {
-					size_t bytesThisPage =
-					    (bytesRemaining >
-					     PAGE_SIZE ? PAGE_SIZE :
-					     bytesRemaining);
-
-					DMA_MAP_PRINT
-					    ("pageIdx:%d pages[pageIdx]=%p pfn=%u phys=%u\n",
-					     pageIdx, pages[pageIdx],
-					     page_to_pfn(pages[pageIdx]),
-					     PFN_PHYS(page_to_pfn
-						      (pages[pageIdx])));
-
-					dma_map_add_segment(memMap,
-							    region,
-							    virtAddr,
-							    PFN_PHYS(page_to_pfn
-								     (pages
-								      [pageIdx])),
-							    bytesThisPage);
-
-					virtAddr += bytesThisPage;
-					bytesRemaining -= bytesThisPage;
-				}
-			}
-#else
-			printk(KERN_ERR
-			       "%s: User mode pages are not yet supported\n",
-			       __func__);
-
-			/* user pages are not physically contiguous */
-
-			rc = -EINVAL;
-#endif
-			break;
-		}
-
-	default:
-		{
-			printk(KERN_ERR "%s: Unsupported memory type: %d\n",
-			       __func__, region->memType);
-
-			rc = -EINVAL;
-			break;
-		}
-	}
-
-	if (rc != 0) {
-		memMap->numRegionsUsed--;
-	}
-
-out:
-
-	DMA_MAP_PRINT("returning %d\n", rc);
-
-	up(&memMap->lock);
-
-	return rc;
-}
-
-EXPORT_SYMBOL(dma_map_add_segment);
-
-/****************************************************************************/
-/**
-*   Maps in a memory region such that it can be used for performing a DMA.
-*
-*   @return     0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-int dma_map_mem(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		void *mem,	/* Virtual address that we want to get a map of */
-		size_t numBytes,	/* Number of bytes being mapped */
-		enum dma_data_direction dir	/* Direction that the mapping will be going */
-    ) {
-	int rc;
-
-	rc = dma_map_start(memMap, dir);
-	if (rc == 0) {
-		rc = dma_map_add_region(memMap, mem, numBytes);
-		if (rc < 0) {
-			/* Since the add fails, this function will fail, and the caller won't */
-			/* call unmap, so we need to do it here. */
-
-			dma_unmap(memMap, 0);
-		}
-	}
-
-	return rc;
-}
-
-EXPORT_SYMBOL(dma_map_mem);
-
-/****************************************************************************/
-/**
-*   Setup a descriptor ring for a given memory map.
-*
-*   It is assumed that the descriptor ring has already been initialized, and
-*   this routine will only reallocate a new descriptor ring if the existing
-*   one is too small.
-*
-*   @return     0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-int dma_map_create_descriptor_ring(DMA_Device_t dev,	/* DMA device (where the ring is stored) */
-				   DMA_MemMap_t *memMap,	/* Memory map that will be used */
-				   dma_addr_t devPhysAddr	/* Physical address of device */
-    ) {
-	int rc;
-	int numDescriptors;
-	DMA_DeviceAttribute_t *devAttr;
-	DMA_Region_t *region;
-	DMA_Segment_t *segment;
-	dma_addr_t srcPhysAddr;
-	dma_addr_t dstPhysAddr;
-	int regionIdx;
-	int segmentIdx;
-
-	devAttr = &DMA_gDeviceAttribute[dev];
-
-	down(&memMap->lock);
-
-	/* Figure out how many descriptors we need */
-
-	numDescriptors = 0;
-	for (regionIdx = 0; regionIdx < memMap->numRegionsUsed; regionIdx++) {
-		region = &memMap->region[regionIdx];
-
-		for (segmentIdx = 0; segmentIdx < region->numSegmentsUsed;
-		     segmentIdx++) {
-			segment = &region->segment[segmentIdx];
-
-			if (memMap->dir == DMA_TO_DEVICE) {
-				srcPhysAddr = segment->physAddr;
-				dstPhysAddr = devPhysAddr;
-			} else {
-				srcPhysAddr = devPhysAddr;
-				dstPhysAddr = segment->physAddr;
-			}
-
-			rc =
-			     dma_calculate_descriptor_count(dev, srcPhysAddr,
-							    dstPhysAddr,
-							    segment->
-							    numBytes);
-			if (rc < 0) {
-				printk(KERN_ERR
-				       "%s: dma_calculate_descriptor_count failed: %d\n",
-				       __func__, rc);
-				goto out;
-			}
-			numDescriptors += rc;
-		}
-	}
-
-	/* Adjust the size of the ring, if it isn't big enough */
-
-	if (numDescriptors > devAttr->ring.descriptorsAllocated) {
-		dma_free_descriptor_ring(&devAttr->ring);
-		rc =
-		     dma_alloc_descriptor_ring(&devAttr->ring,
-					       numDescriptors);
-		if (rc < 0) {
-			printk(KERN_ERR
-			       "%s: dma_alloc_descriptor_ring failed: %d\n",
-			       __func__, rc);
-			goto out;
-		}
-	} else {
-		rc =
-		     dma_init_descriptor_ring(&devAttr->ring,
-					      numDescriptors);
-		if (rc < 0) {
-			printk(KERN_ERR
-			       "%s: dma_init_descriptor_ring failed: %d\n",
-			       __func__, rc);
-			goto out;
-		}
-	}
-
-	/* Populate the descriptors */
-
-	for (regionIdx = 0; regionIdx < memMap->numRegionsUsed; regionIdx++) {
-		region = &memMap->region[regionIdx];
-
-		for (segmentIdx = 0; segmentIdx < region->numSegmentsUsed;
-		     segmentIdx++) {
-			segment = &region->segment[segmentIdx];
-
-			if (memMap->dir == DMA_TO_DEVICE) {
-				srcPhysAddr = segment->physAddr;
-				dstPhysAddr = devPhysAddr;
-			} else {
-				srcPhysAddr = devPhysAddr;
-				dstPhysAddr = segment->physAddr;
-			}
-
-			rc =
-			     dma_add_descriptors(&devAttr->ring, dev,
-						 srcPhysAddr, dstPhysAddr,
-						 segment->numBytes);
-			if (rc < 0) {
-				printk(KERN_ERR
-				       "%s: dma_add_descriptors failed: %d\n",
-				       __func__, rc);
-				goto out;
-			}
-		}
-	}
-
-	rc = 0;
-
-out:
-
-	up(&memMap->lock);
-	return rc;
-}
-
-EXPORT_SYMBOL(dma_map_create_descriptor_ring);
-
-/****************************************************************************/
-/**
-*   Maps in a memory region such that it can be used for performing a DMA.
-*
-*   @return
-*/
-/****************************************************************************/
-
-int dma_unmap(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-	      int dirtied	/* non-zero if any of the pages were modified */
-    ) {
-
-	int rc = 0;
-	int regionIdx;
-	int segmentIdx;
-	DMA_Region_t *region;
-	DMA_Segment_t *segment;
-
-	down(&memMap->lock);
-
-	for (regionIdx = 0; regionIdx < memMap->numRegionsUsed; regionIdx++) {
-		region = &memMap->region[regionIdx];
-
-		for (segmentIdx = 0; segmentIdx < region->numSegmentsUsed;
-		     segmentIdx++) {
-			segment = &region->segment[segmentIdx];
-
-			switch (region->memType) {
-			case DMA_MEM_TYPE_VMALLOC:
-				{
-					printk(KERN_ERR
-					       "%s: vmalloc'd pages are not yet supported\n",
-					       __func__);
-					rc = -EINVAL;
-					goto out;
-				}
-
-			case DMA_MEM_TYPE_KMALLOC:
-				{
-#if ALLOW_MAP_OF_KMALLOC_MEMORY
-					dma_unmap_single(NULL,
-							 segment->physAddr,
-							 segment->numBytes,
-							 memMap->dir);
-#endif
-					break;
-				}
-
-			case DMA_MEM_TYPE_DMA:
-				{
-					dma_sync_single_for_cpu(NULL,
-								segment->
-								physAddr,
-								segment->
-								numBytes,
-								memMap->dir);
-					break;
-				}
-
-			case DMA_MEM_TYPE_USER:
-				{
-					/* Nothing to do here. */
-
-					break;
-				}
-
-			default:
-				{
-					printk(KERN_ERR
-					       "%s: Unsupported memory type: %d\n",
-					       __func__, region->memType);
-					rc = -EINVAL;
-					goto out;
-				}
-			}
-
-			segment->virtAddr = NULL;
-			segment->physAddr = 0;
-			segment->numBytes = 0;
-		}
-
-		if (region->numLockedPages > 0) {
-			int pageIdx;
-
-			/* Some user pages were locked. We need to go and unlock them now. */
-
-			for (pageIdx = 0; pageIdx < region->numLockedPages;
-			     pageIdx++) {
-				struct page *page =
-				    region->lockedPages[pageIdx];
-
-				if (memMap->dir == DMA_FROM_DEVICE) {
-					SetPageDirty(page);
-				}
-				page_cache_release(page);
-			}
-			kfree(region->lockedPages);
-			region->numLockedPages = 0;
-			region->lockedPages = NULL;
-		}
-
-		region->memType = DMA_MEM_TYPE_NONE;
-		region->virtAddr = NULL;
-		region->numBytes = 0;
-		region->numSegmentsUsed = 0;
-	}
-	memMap->userTask = NULL;
-	memMap->numRegionsUsed = 0;
-	memMap->inUse = 0;
-
-out:
-	up(&memMap->lock);
-
-	return rc;
-}
-
-EXPORT_SYMBOL(dma_unmap);

arch/arm/mach-bcmring/include/mach/dma.h

@@ -26,15 +26,9 @@
 /* ---- Include Files ---------------------------------------------------- */
 
 #include <linux/kernel.h>
-#include <linux/wait.h>
 #include <linux/semaphore.h>
 #include <csp/dmacHw.h>
 #include <mach/timer.h>
-#include <linux/scatterlist.h>
-#include <linux/dma-mapping.h>
-#include <linux/mm.h>
-#include <linux/vmalloc.h>
-#include <linux/pagemap.h>
 
 /* ---- Constants and Types ---------------------------------------------- */
 
@@ -111,78 +105,6 @@ typedef struct {
 
 } DMA_DescriptorRing_t;
 
-/****************************************************************************
-*
-*   The DMA_MemType_t and DMA_MemMap_t are helper structures used to setup
-*   DMA chains from a variety of memory sources.
-*
-*****************************************************************************/
-
-#define DMA_MEM_MAP_MIN_SIZE    4096	/* Pages less than this size are better */
-					/* off not being DMA'd. */
-
-typedef enum {
-	DMA_MEM_TYPE_NONE,	/* Not a valid setting */
-	DMA_MEM_TYPE_VMALLOC,	/* Memory came from vmalloc call */
-	DMA_MEM_TYPE_KMALLOC,	/* Memory came from kmalloc call */
-	DMA_MEM_TYPE_DMA,	/* Memory came from dma_alloc_xxx call */
-	DMA_MEM_TYPE_USER,	/* Memory came from user space. */
-
-} DMA_MemType_t;
-
-/* A segment represents a physically and virtually contiguous chunk of memory. */
-/* i.e. each segment can be DMA'd */
-/* A user of the DMA code will add memory regions. Each region may need to be */
-/* represented by one or more segments. */
-
-typedef struct {
-	void *virtAddr;		/* Virtual address used for this segment */
-	dma_addr_t physAddr;	/* Physical address this segment maps to */
-	size_t numBytes;	/* Size of the segment, in bytes */
-
-} DMA_Segment_t;
-
-/* A region represents a virtually contiguous chunk of memory, which may be */
-/* made up of multiple segments. */
-
-typedef struct {
-	DMA_MemType_t memType;
-	void *virtAddr;
-	size_t numBytes;
-
-	/* Each region (virtually contiguous) consists of one or more segments. Each */
-	/* segment is virtually and physically contiguous. */
-
-	int numSegmentsUsed;
-	int numSegmentsAllocated;
-	DMA_Segment_t *segment;
-
-	/* When a region corresponds to user memory, we need to lock all of the pages */
-	/* down before we can figure out the physical addresses. The lockedPage array contains */
-	/* the pages that were locked, and which subsequently need to be unlocked once the */
-	/* memory is unmapped. */
-
-	unsigned numLockedPages;
-	struct page **lockedPages;
-
-} DMA_Region_t;
-
-typedef struct {
-	int inUse;		/* Is this mapping currently being used? */
-	struct semaphore lock;	/* Acquired when using this structure */
-	enum dma_data_direction dir;	/* Direction this transfer is intended for */
-
-	/* In the event that we're mapping user memory, we need to know which task */
-	/* the memory is for, so that we can obtain the correct mm locks. */
-
-	struct task_struct *userTask;
-
-	int numRegionsUsed;
-	int numRegionsAllocated;
-	DMA_Region_t *region;
-
-} DMA_MemMap_t;
-
 /****************************************************************************
 *
 *   The DMA_DeviceAttribute_t contains information which describes a
@@ -568,124 +490,6 @@ int dma_alloc_double_dst_descriptors(DMA_Handle_t handle,	/* DMA Handle */
 				     size_t numBytes	/* Number of bytes in each destination buffer */
     );
 
-/****************************************************************************/
-/**
-*   Initializes a DMA_MemMap_t data structure
-*/
-/****************************************************************************/
-
-int dma_init_mem_map(DMA_MemMap_t *memMap	/* Stores state information about the map */
-    );
-
-/****************************************************************************/
-/**
-*   Releases any memory currently being held by a memory mapping structure.
-*/
-/****************************************************************************/
-
-int dma_term_mem_map(DMA_MemMap_t *memMap	/* Stores state information about the map */
-    );
-
-/****************************************************************************/
-/**
-*   Looks at a memory address and categorizes it.
-*
-*   @return One of the values from the DMA_MemType_t enumeration.
-*/
-/****************************************************************************/
-
-DMA_MemType_t dma_mem_type(void *addr);
-
-/****************************************************************************/
-/**
-*   Sets the process (aka userTask) associated with a mem map. This is
-*   required if user-mode segments will be added to the mapping.
-*/
-/****************************************************************************/
-
-static inline void dma_mem_map_set_user_task(DMA_MemMap_t *memMap,
-					     struct task_struct *task)
-{
-	memMap->userTask = task;
-}
-
-/****************************************************************************/
-/**
-*   Looks at a memory address and determines if we support DMA'ing to/from
-*   that type of memory.
-*
-*   @return boolean -
-*               return value != 0 means dma supported
-*               return value == 0 means dma not supported
-*/
-/****************************************************************************/
-
-int dma_mem_supports_dma(void *addr);
-
-/****************************************************************************/
-/**
-*   Initializes a memory map for use. Since this function acquires a
-*   sempaphore within the memory map, it is VERY important that dma_unmap
-*   be called when you're finished using the map.
-*/
-/****************************************************************************/
-
-int dma_map_start(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		  enum dma_data_direction dir	/* Direction that the mapping will be going */
-    );
-
-/****************************************************************************/
-/**
-*   Adds a segment of memory to a memory map.
-*
-*   @return     0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-int dma_map_add_region(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		       void *mem,	/* Virtual address that we want to get a map of */
-		       size_t numBytes	/* Number of bytes being mapped */
-    );
-
-/****************************************************************************/
-/**
-*   Creates a descriptor ring from a memory mapping.
-*
-*   @return 0 on success, error code otherwise.
-*/
-/****************************************************************************/
-
-int dma_map_create_descriptor_ring(DMA_Device_t dev,	/* DMA device (where the ring is stored) */
-				   DMA_MemMap_t *memMap,	/* Memory map that will be used */
-				   dma_addr_t devPhysAddr	/* Physical address of device */
-    );
-
-/****************************************************************************/
-/**
-*   Maps in a memory region such that it can be used for performing a DMA.
-*
-*   @return
-*/
-/****************************************************************************/
-
-int dma_map_mem(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-		void *addr,	/* Virtual address that we want to get a map of */
-		size_t count,	/* Number of bytes being mapped */
-		enum dma_data_direction dir	/* Direction that the mapping will be going */
-    );
-
-/****************************************************************************/
-/**
-*   Maps in a memory region such that it can be used for performing a DMA.
-*
-*   @return
-*/
-/****************************************************************************/
-
-int dma_unmap(DMA_MemMap_t *memMap,	/* Stores state information about the map */
-	      int dirtied	/* non-zero if any of the pages were modified */
-    );
-
 /****************************************************************************/
 /**
 *   Initiates a transfer when the descriptors have already been setup.

arch/arm/mach-davinci/board-da850-evm.c

@@ -44,7 +44,7 @@
 #include <mach/aemif.h>
 #include <mach/spi.h>
 
-#define DA850_EVM_PHY_ID		"0:00"
+#define DA850_EVM_PHY_ID		"davinci_mdio-0:00"
 #define DA850_LCD_PWR_PIN		GPIO_TO_PIN(2, 8)
 #define DA850_LCD_BL_PIN		GPIO_TO_PIN(2, 15)
 

arch/arm/mach-davinci/board-dm365-evm.c

@@ -54,7 +54,7 @@ static inline int have_tvp7002(void)
 	return 0;
 }
 
-#define DM365_EVM_PHY_ID		"0:01"
+#define DM365_EVM_PHY_ID		"davinci_mdio-0:01"
 /*
  * A MAX-II CPLD is used for various board control functions.
  */

arch/arm/mach-davinci/board-dm644x-evm.c

@@ -40,7 +40,7 @@
 #include <mach/usb.h>
 #include <mach/aemif.h>
 
-#define DM644X_EVM_PHY_ID		"0:01"
+#define DM644X_EVM_PHY_ID		"davinci_mdio-0:01"
 #define LXT971_PHY_ID	(0x001378e2)
 #define LXT971_PHY_MASK	(0xfffffff0)
 

arch/arm/mach-davinci/board-dm646x-evm.c

@@ -736,7 +736,7 @@ static struct davinci_uart_config uart_config __initdata = {
 	.enabled_uarts = (1 << 0),
 };
 
-#define DM646X_EVM_PHY_ID		"0:01"
+#define DM646X_EVM_PHY_ID		"davinci_mdio-0:01"
 /*
  * The following EDMA channels/slots are not being used by drivers (for
  * example: Timer, GPIO, UART events etc) on dm646x, hence they are being

arch/arm/mach-davinci/board-neuros-osd2.c

@@ -39,7 +39,7 @@
 #include <mach/mmc.h>
 #include <mach/usb.h>
 
-#define NEUROS_OSD2_PHY_ID		"0:01"
+#define NEUROS_OSD2_PHY_ID		"davinci_mdio-0:01"
 #define LXT971_PHY_ID			0x001378e2
 #define LXT971_PHY_MASK			0xfffffff0
 

arch/arm/mach-davinci/board-omapl138-hawk.c

@@ -21,7 +21,7 @@
 #include <mach/da8xx.h>
 #include <mach/mux.h>
 
-#define HAWKBOARD_PHY_ID		"0:07"
+#define HAWKBOARD_PHY_ID		"davinci_mdio-0:07"
 #define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
 #define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)
 

arch/arm/mach-davinci/board-sffsdr.c

@@ -42,7 +42,7 @@
 #include <mach/mux.h>
 #include <mach/usb.h>
 
-#define SFFSDR_PHY_ID		"0:01"
+#define SFFSDR_PHY_ID		"davinci_mdio-0:01"
 static struct mtd_partition davinci_sffsdr_nandflash_partition[] = {
 	/* U-Boot Environment: Block 0
 	 * UBL:                Block 1

arch/arm/mach-davinci/da850.c

@@ -153,34 +153,6 @@ static struct clk pll1_sysclk3 = {
 	.div_reg	= PLLDIV3,
 };
 
-static struct clk pll1_sysclk4 = {
-	.name		= "pll1_sysclk4",
-	.parent		= &pll1_clk,
-	.flags		= CLK_PLL,
-	.div_reg	= PLLDIV4,
-};
-
-static struct clk pll1_sysclk5 = {
-	.name		= "pll1_sysclk5",
-	.parent		= &pll1_clk,
-	.flags		= CLK_PLL,
-	.div_reg	= PLLDIV5,
-};
-
-static struct clk pll1_sysclk6 = {
-	.name		= "pll0_sysclk6",
-	.parent		= &pll0_clk,
-	.flags		= CLK_PLL,
-	.div_reg	= PLLDIV6,
-};
-
-static struct clk pll1_sysclk7 = {
-	.name		= "pll1_sysclk7",
-	.parent		= &pll1_clk,
-	.flags		= CLK_PLL,
-	.div_reg	= PLLDIV7,
-};
-
 static struct clk i2c0_clk = {
 	.name		= "i2c0",
 	.parent		= &pll0_aux_clk,
@@ -397,10 +369,6 @@ static struct clk_lookup da850_clks[] = {
 	CLK(NULL,		"pll1_aux",	&pll1_aux_clk),
 	CLK(NULL,		"pll1_sysclk2",	&pll1_sysclk2),
 	CLK(NULL,		"pll1_sysclk3",	&pll1_sysclk3),
-	CLK(NULL,		"pll1_sysclk4",	&pll1_sysclk4),
-	CLK(NULL,		"pll1_sysclk5",	&pll1_sysclk5),
-	CLK(NULL,		"pll1_sysclk6",	&pll1_sysclk6),
-	CLK(NULL,		"pll1_sysclk7",	&pll1_sysclk7),
 	CLK("i2c_davinci.1",	NULL,		&i2c0_clk),
 	CLK(NULL,		"timer0",	&timerp64_0_clk),
 	CLK("watchdog",		NULL,		&timerp64_1_clk),

arch/arm/mach-dove/common.c

@@ -28,6 +28,7 @@
 #include <asm/mach/arch.h>
 #include <linux/irq.h>
 #include <plat/time.h>
+#include <plat/ehci-orion.h>
 #include <plat/common.h>
 #include <plat/addr-map.h>
 #include "common.h"
@@ -71,7 +72,7 @@ void __init dove_map_io(void)
  ****************************************************************************/
 void __init dove_ehci0_init(void)
 {
-	orion_ehci_init(DOVE_USB0_PHYS_BASE, IRQ_DOVE_USB0);
+	orion_ehci_init(DOVE_USB0_PHYS_BASE, IRQ_DOVE_USB0, EHCI_PHY_NA);
 }
 
 /*****************************************************************************

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -32,7 +32,9 @@
 #include <mach/hardware.h>
 #include <mach/fb.h>
 #include <mach/ep93xx_spi.h>
+#include <mach/gpio-ep93xx.h>
 
+#include <asm/hardware/vic.h>
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
 #include <asm/mach/arch.h>
@@ -153,7 +155,6 @@ static struct i2c_board_info vision_i2c_info[] __initdata = {
 	}, {
 		I2C_BOARD_INFO("pca9539", 0x74),
 		.platform_data	= &pca953x_74_gpio_data,
-		.irq		= gpio_to_irq(EP93XX_GPIO_LINE_F(7)),
 	}, {
 		I2C_BOARD_INFO("pca9539", 0x75),
 		.platform_data	= &pca953x_75_gpio_data,
@@ -348,6 +349,8 @@ static void __init vision_init_machine(void)
 				"pca9539:74"))
 		pr_warn("cannot request interrupt gpio for pca9539:74\n");
 
+	vision_i2c_info[1].irq = gpio_to_irq(EP93XX_GPIO_LINE_F(7));
+
 	ep93xx_register_i2c(&vision_i2c_gpio_data, vision_i2c_info,
 				ARRAY_SIZE(vision_i2c_info));
 	ep93xx_register_spi(&vision_spi_master, vision_spi_board_info,
@@ -359,6 +362,7 @@ MACHINE_START(VISION_EP9307, "Vision Engraving Systems EP9307")
 	.atag_offset	= 0x100,
 	.map_io		= vision_map_io,
 	.init_irq	= ep93xx_init_irq,
+	.handle_irq	= vic_handle_irq,
 	.timer		= &ep93xx_timer,
 	.init_machine	= vision_init_machine,
 	.restart	= ep93xx_restart,

arch/arm/mach-exynos/clock-exynos4210.c

@@ -32,6 +32,7 @@
 
 #include "common.h"
 
+#ifdef CONFIG_PM_SLEEP
 static struct sleep_save exynos4210_clock_save[] = {
 	SAVE_ITEM(S5P_CLKSRC_IMAGE),
 	SAVE_ITEM(S5P_CLKSRC_LCD1),
@@ -42,6 +43,7 @@ static struct sleep_save exynos4210_clock_save[] = {
 	SAVE_ITEM(S5P_CLKGATE_IP_LCD1),
 	SAVE_ITEM(S5P_CLKGATE_IP_PERIR_4210),
 };
+#endif
 
 static struct clksrc_clk *sysclks[] = {
 	/* nothing here yet */

arch/arm/mach-exynos/clock-exynos4212.c

@@ -32,12 +32,14 @@
 
 #include "common.h"
 
+#ifdef CONFIG_PM_SLEEP
 static struct sleep_save exynos4212_clock_save[] = {
 	SAVE_ITEM(S5P_CLKSRC_IMAGE),
 	SAVE_ITEM(S5P_CLKDIV_IMAGE),
 	SAVE_ITEM(S5P_CLKGATE_IP_IMAGE_4212),
 	SAVE_ITEM(S5P_CLKGATE_IP_PERIR_4212),
 };
+#endif
 
 static struct clk *clk_src_mpll_user_list[] = {
 	[0] = &clk_fin_mpll,

arch/arm/mach-exynos/clock.c

@@ -30,6 +30,7 @@
 
 #include "common.h"
 
+#ifdef CONFIG_PM_SLEEP
 static struct sleep_save exynos4_clock_save[] = {
 	SAVE_ITEM(S5P_CLKDIV_LEFTBUS),
 	SAVE_ITEM(S5P_CLKGATE_IP_LEFTBUS),
@@ -93,6 +94,7 @@ static struct sleep_save exynos4_clock_save[] = {
 	SAVE_ITEM(S5P_CLKGATE_SCLKCPU),
 	SAVE_ITEM(S5P_CLKGATE_IP_CPU),
 };
+#endif
 
 struct clk clk_sclk_hdmi27m = {
 	.name		= "sclk_hdmi27m",