Merge branch 'for-2639/i2c/i2c-tegra' of git://git.fluff.org/bjdooks/linux into for-next-i2c

.gitignore

@@ -28,6 +28,7 @@ modules.builtin
 *.gz
 *.bz2
 *.lzma
+*.xz
 *.lzo
 *.patch
 *.gcno

Documentation/DocBook/drm.tmpl

@@ -73,8 +73,8 @@
       services.
     </para>
     <para>
-      The core of every DRM driver is struct drm_device.  Drivers
-      will typically statically initialize a drm_device structure,
+      The core of every DRM driver is struct drm_driver.  Drivers
+      will typically statically initialize a drm_driver structure,
       then pass it to drm_init() at load time.
     </para>
 
@@ -84,7 +84,7 @@
     <title>Driver initialization</title>
     <para>
       Before calling the DRM initialization routines, the driver must
-      first create and fill out a struct drm_device structure.
+      first create and fill out a struct drm_driver structure.
     </para>
     <programlisting>
       static struct drm_driver driver = {

Documentation/DocBook/filesystems.tmpl

@@ -82,6 +82,11 @@
      </sect1>
   </chapter>
 
+  <chapter id="fs_events">
+     <title>Events based on file descriptors</title>
+!Efs/eventfd.c
+  </chapter>
+
   <chapter id="sysfs">
      <title>The Filesystem for Exporting Kernel Objects</title>
 !Efs/sysfs/file.c

Documentation/powerpc/booting-without-of.txt → Documentation/devicetree/booting-without-of.txt

@@ -13,7 +13,6 @@ Table of Contents
 
   I - Introduction
     1) Entry point for arch/powerpc
-    2) Board support
 
   II - The DT block format
     1) Header
@@ -41,13 +40,6 @@ Table of Contents
   VI - System-on-a-chip devices and nodes
     1) Defining child nodes of an SOC
     2) Representing devices without a current OF specification
-      a) PHY nodes
-      b) Interrupt controllers
-      c) 4xx/Axon EMAC ethernet nodes
-      d) Xilinx IP cores
-      e) USB EHCI controllers
-      f) MDIO on GPIOs
-      g) SPI busses
 
   VII - Specifying interrupt information for devices
     1) interrupts property
@@ -123,7 +115,7 @@ Revision Information
 I - Introduction
 ================
 
-During the recent development of the Linux/ppc64 kernel, and more
+During the development of the Linux/ppc64 kernel, and more
 specifically, the addition of new platform types outside of the old
 IBM pSeries/iSeries pair, it was decided to enforce some strict rules
 regarding the kernel entry and bootloader <-> kernel interfaces, in
@@ -146,7 +138,7 @@ section III, but, for example, the kernel does not require you to
 create a node for every PCI device in the system. It is a requirement
 to have a node for PCI host bridges in order to provide interrupt
 routing informations and memory/IO ranges, among others. It is also
-recommended to define nodes for on chip devices and other busses that
+recommended to define nodes for on chip devices and other buses that
 don't specifically fit in an existing OF specification. This creates a
 great flexibility in the way the kernel can then probe those and match
 drivers to device, without having to hard code all sorts of tables. It
@@ -158,7 +150,7 @@ it with special cases.
 1) Entry point for arch/powerpc
 -------------------------------
 
-   There is one and one single entry point to the kernel, at the start
+   There is one single entry point to the kernel, at the start
    of the kernel image. That entry point supports two calling
    conventions:
 
@@ -210,12 +202,6 @@ it with special cases.
         with all CPUs. The way to do that with method b) will be
         described in a later revision of this document.
 
-
-2) Board support
-----------------
-
-64-bit kernels:
-
    Board supports (platforms) are not exclusive config options. An
    arbitrary set of board supports can be built in a single kernel
    image. The kernel will "know" what set of functions to use for a
@@ -234,48 +220,11 @@ it with special cases.
         containing the various callbacks that the generic code will
         use to get to your platform specific code
 
-        c) Add a reference to your "ppc_md" structure in the
-        "machines" table in arch/powerpc/kernel/setup_64.c if you are
-        a 64-bit platform.
-
-        d) request and get assigned a platform number (see PLATFORM_*
-        constants in arch/powerpc/include/asm/processor.h
-
-32-bit embedded kernels:
-
-  Currently, board support is essentially an exclusive config option.
-  The kernel is configured for a single platform.  Part of the reason
-  for this is to keep kernels on embedded systems small and efficient;
-  part of this is due to the fact the code is already that way. In the
-  future, a kernel may support multiple platforms, but only if the
+  A kernel image may support multiple platforms, but only if the
   platforms feature the same core architecture.  A single kernel build
   cannot support both configurations with Book E and configurations
   with classic Powerpc architectures.
 
-  32-bit embedded platforms that are moved into arch/powerpc using a
-  flattened device tree should adopt the merged tree practice of
-  setting ppc_md up dynamically, even though the kernel is currently
-  built with support for only a single platform at a time.  This allows
-  unification of the setup code, and will make it easier to go to a
-  multiple-platform-support model in the future.
-
-NOTE: I believe the above will be true once Ben's done with the merge
-of the boot sequences.... someone speak up if this is wrong!
-
-  To add a 32-bit embedded platform support, follow the instructions
-  for 64-bit platforms above, with the exception that the Kconfig
-  option should be set up such that the kernel builds exclusively for
-  the platform selected.  The processor type for the platform should
-  enable another config option to select the specific board
-  supported.
-
-NOTE: If Ben doesn't merge the setup files, may need to change this to
-point to setup_32.c
-
-
-   I will describe later the boot process and various callbacks that
-   your platform should implement.
-
 
 II - The DT block format
 ========================
@@ -300,8 +249,8 @@ the block to RAM before passing it to the kernel.
 1) Header
 ---------
 
-   The kernel is entered with r3 pointing to an area of memory that is
-   roughly described in arch/powerpc/include/asm/prom.h by the structure
+   The kernel is passed the physical address pointing to an area of memory
+   that is roughly described in include/linux/of_fdt.h by the structure
    boot_param_header:
 
 struct boot_param_header {
@@ -339,7 +288,7 @@ struct boot_param_header {
    All values in this header are in big endian format, the various
    fields in this header are defined more precisely below. All
    "offset" values are in bytes from the start of the header; that is
-   from the value of r3.
+   from the physical base address of the device tree block.
 
    - magic
 
@@ -437,7 +386,7 @@ struct boot_param_header {
 
 
              ------------------------------
-       r3 -> |  struct boot_param_header  |
+     base -> |  struct boot_param_header  |
              ------------------------------
              |      (alignment gap) (*)   |
              ------------------------------
@@ -457,7 +406,7 @@ struct boot_param_header {
       -----> ------------------------------
       |
       |
-      --- (r3 + totalsize)
+      --- (base + totalsize)
 
   (*) The alignment gaps are not necessarily present; their presence
       and size are dependent on the various alignment requirements of
@@ -500,7 +449,7 @@ the device-tree structure. It is typically used to represent "path" in
 the device-tree. More details about the actual format of these will be
 below.
 
-The kernel powerpc generic code does not make any formal use of the
+The kernel generic code does not make any formal use of the
 unit address (though some board support code may do) so the only real
 requirement here for the unit address is to ensure uniqueness of
 the node unit name at a given level of the tree. Nodes with no notion
@@ -518,20 +467,21 @@ path to the root node is "/".
 
 Every node which actually represents an actual device (that is, a node
 which isn't only a virtual "container" for more nodes, like "/cpus"
-is) is also required to have a "device_type" property indicating the
-type of node .
+is) is also required to have a "compatible" property indicating the
+specific hardware and an optional list of devices it is fully
+backwards compatible with.
 
 Finally, every node that can be referenced from a property in another
-node is required to have a "linux,phandle" property. Real open
-firmware implementations provide a unique "phandle" value for every
-node that the "prom_init()" trampoline code turns into
-"linux,phandle" properties. However, this is made optional if the
-flattened device tree is used directly. An example of a node
+node is required to have either a "phandle" or a "linux,phandle"
+property. Real Open Firmware implementations provide a unique
+"phandle" value for every node that the "prom_init()" trampoline code
+turns into "linux,phandle" properties. However, this is made optional
+if the flattened device tree is used directly. An example of a node
 referencing another node via "phandle" is when laying out the
 interrupt tree which will be described in a further version of this
 document.
 
-This "linux, phandle" property is a 32-bit value that uniquely
+The "phandle" property is a 32-bit value that uniquely
 identifies a node. You are free to use whatever values or system of
 values, internal pointers, or whatever to generate these, the only
 requirement is that every node for which you provide that property has
@@ -694,7 +644,7 @@ made of 3 cells, the bottom two containing the actual address itself
 while the top cell contains address space indication, flags, and pci
 bus & device numbers.
 
-For busses that support dynamic allocation, it's the accepted practice
+For buses that support dynamic allocation, it's the accepted practice
 to then not provide the address in "reg" (keep it 0) though while
 providing a flag indicating the address is dynamically allocated, and
 then, to provide a separate "assigned-addresses" property that
@@ -711,7 +661,7 @@ prom_parse.c file of the recent kernels for your bus type.
 The "reg" property only defines addresses and sizes (if #size-cells is
 non-0) within a given bus. In order to translate addresses upward
 (that is into parent bus addresses, and possibly into CPU physical
-addresses), all busses must contain a "ranges" property. If the
+addresses), all buses must contain a "ranges" property. If the
 "ranges" property is missing at a given level, it's assumed that
 translation isn't possible, i.e., the registers are not visible on the
 parent bus.  The format of the "ranges" property for a bus is a list
@@ -727,9 +677,9 @@ example, for a PCI host controller, that would be a CPU address. For a
 PCI<->ISA bridge, that would be a PCI address. It defines the base
 address in the parent bus where the beginning of that range is mapped.
 
-For a new 64-bit powerpc board, I recommend either the 2/2 format or
+For new 64-bit board support, I recommend either the 2/2 format or
 Apple's 2/1 format which is slightly more compact since sizes usually
-fit in a single 32-bit word.   New 32-bit powerpc boards should use a
+fit in a single 32-bit word.   New 32-bit board support should use a
 1/1 format, unless the processor supports physical addresses greater
 than 32-bits, in which case a 2/1 format is recommended.
 
@@ -754,7 +704,7 @@ of their actual names.
 While earlier users of Open Firmware like OldWorld macintoshes tended
 to use the actual device name for the "name" property, it's nowadays
 considered a good practice to use a name that is closer to the device
-class (often equal to device_type). For example, nowadays, ethernet
+class (often equal to device_type). For example, nowadays, Ethernet
 controllers are named "ethernet", an additional "model" property
 defining precisely the chip type/model, and "compatible" property
 defining the family in case a single driver can driver more than one
@@ -772,7 +722,7 @@ is present).
 4) Note about node and property names and character set
 -------------------------------------------------------
 
-While open firmware provides more flexible usage of 8859-1, this
+While Open Firmware provides more flexible usage of 8859-1, this
 specification enforces more strict rules. Nodes and properties should
 be comprised only of ASCII characters 'a' to 'z', '0' to
 '9', ',', '.', '_', '+', '#', '?', and '-'. Node names additionally
@@ -792,7 +742,7 @@ address which can extend beyond that limit.
 --------------------------------
   These are all that are currently required. However, it is strongly
   recommended that you expose PCI host bridges as documented in the
-  PCI binding to open firmware, and your interrupt tree as documented
+  PCI binding to Open Firmware, and your interrupt tree as documented
   in OF interrupt tree specification.
 
   a) The root node
@@ -802,20 +752,12 @@ address which can extend beyond that limit.
     - model : this is your board name/model
     - #address-cells : address representation for "root" devices
     - #size-cells: the size representation for "root" devices
-    - device_type : This property shouldn't be necessary. However, if
-      you decide to create a device_type for your root node, make sure it
-      is _not_ "chrp" unless your platform is a pSeries or PAPR compliant
-      one for 64-bit, or a CHRP-type machine for 32-bit as this will
-      matched by the kernel this way.
-
-  Additionally, some recommended properties are:
-
     - compatible : the board "family" generally finds its way here,
       for example, if you have 2 board models with a similar layout,
       that typically get driven by the same platform code in the
-      kernel, you would use a different "model" property but put a
-      value in "compatible". The kernel doesn't directly use that
-      value but it is generally useful.
+      kernel, you would specify the exact board model in the
+      compatible property followed by an entry that represents the SoC
+      model.
 
   The root node is also generally where you add additional properties
   specific to your board like the serial number if any, that sort of
@@ -841,8 +783,11 @@ address which can extend beyond that limit.
 
   So under /cpus, you are supposed to create a node for every CPU on
   the machine. There is no specific restriction on the name of the
-  CPU, though It's common practice to call it PowerPC,<name>. For
+  CPU, though it's common to call it <architecture>,<core>. For
   example, Apple uses PowerPC,G5 while IBM uses PowerPC,970FX.
+  However, the Generic Names convention suggests that it would be
+  better to simply use 'cpu' for each cpu node and use the compatible
+  property to identify the specific cpu core.
 
   Required properties:
 
@@ -923,7 +868,7 @@ compatibility.
 
   e) The /chosen node
 
-  This node is a bit "special". Normally, that's where open firmware
+  This node is a bit "special". Normally, that's where Open Firmware
   puts some variable environment information, like the arguments, or
   the default input/output devices.
 
@@ -940,11 +885,7 @@ compatibility.
       console device if any. Typically, if you have serial devices on
       your board, you may want to put the full path to the one set as
       the default console in the firmware here, for the kernel to pick
-      it up as its own default console. If you look at the function
-      set_preferred_console() in arch/ppc64/kernel/setup.c, you'll see
-      that the kernel tries to find out the default console and has
-      knowledge of various types like 8250 serial ports. You may want
-      to extend this function to add your own.
+      it up as its own default console.
 
   Note that u-boot creates and fills in the chosen node for platforms
   that use it.
@@ -955,23 +896,23 @@ compatibility.
 
   f) the /soc<SOCname> node
 
-  This node is used to represent a system-on-a-chip (SOC) and must be
-  present if the processor is a SOC. The top-level soc node contains
-  information that is global to all devices on the SOC. The node name
-  should contain a unit address for the SOC, which is the base address
-  of the memory-mapped register set for the SOC. The name of an soc
+  This node is used to represent a system-on-a-chip (SoC) and must be
+  present if the processor is a SoC. The top-level soc node contains
+  information that is global to all devices on the SoC. The node name
+  should contain a unit address for the SoC, which is the base address
+  of the memory-mapped register set for the SoC. The name of an SoC
   node should start with "soc", and the remainder of the name should
   represent the part number for the soc.  For example, the MPC8540's
   soc node would be called "soc8540".
 
   Required properties:
 
-    - device_type : Should be "soc"
     - ranges : Should be defined as specified in 1) to describe the
-      translation of SOC addresses for memory mapped SOC registers.
-    - bus-frequency: Contains the bus frequency for the SOC node.
+      translation of SoC addresses for memory mapped SoC registers.
+    - bus-frequency: Contains the bus frequency for the SoC node.
       Typically, the value of this field is filled in by the boot
       loader.
+    - compatible : Exact model of the SoC
 
 
   Recommended properties:
@@ -1155,12 +1096,13 @@ while all this has been defined and implemented.
 
   - An example of code for iterating nodes & retrieving properties
     directly from the flattened tree format can be found in the kernel
-    file arch/ppc64/kernel/prom.c, look at scan_flat_dt() function,
+    file drivers/of/fdt.c.  Look at the of_scan_flat_dt() function,
     its usage in early_init_devtree(), and the corresponding various
     early_init_dt_scan_*() callbacks. That code can be re-used in a
     GPL bootloader, and as the author of that code, I would be happy
     to discuss possible free licensing to any vendor who wishes to
     integrate all or part of this code into a non-GPL bootloader.
+    (reference needed; who is 'I' here? ---gcl Jan 31, 2011)
 
 
 
@@ -1203,18 +1145,19 @@ MPC8540.
 2) Representing devices without a current OF specification
 ----------------------------------------------------------
 
-Currently, there are many devices on SOCs that do not have a standard
-representation pre-defined as part of the open firmware
-specifications, mainly because the boards that contain these SOCs are
-not currently booted using open firmware.   This section contains
-descriptions for the SOC devices for which new nodes have been
-defined; this list will expand as more and more SOC-containing
-platforms are moved over to use the flattened-device-tree model.
+Currently, there are many devices on SoCs that do not have a standard
+representation defined as part of the Open Firmware specifications,
+mainly because the boards that contain these SoCs are not currently
+booted using Open Firmware.  Binding documentation for new devices
+should be added to the Documentation/devicetree/bindings directory.
+That directory will expand as device tree support is added to more and
+more SoCs.
+
 
 VII - Specifying interrupt information for devices
 ===================================================
 
-The device tree represents the busses and devices of a hardware
+The device tree represents the buses and devices of a hardware
 system in a form similar to the physical bus topology of the
 hardware.
 

Documentation/hwmon/jc42

@@ -51,7 +51,8 @@ Supported chips:
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f
-    Datasheet: -
+    Datasheet:
+	http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf
 
 Author:
 	Guenter Roeck <guenter.roeck@ericsson.com>
@@ -60,7 +61,11 @@ Author:
 Description
 -----------
 
-This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
+This driver implements support for JEDEC JC 42.4 compliant temperature sensors,
+which are used on many DDR3 memory modules for mobile devices and servers. Some
+systems use the sensor to prevent memory overheating by automatically throttling
+the memory controller.
+
 The driver auto-detects the chips listed above, but can be manually instantiated
 to support other JC 42.4 compliant chips.
 
@@ -81,15 +86,19 @@ limits. The chip supports only a single register to configure the hysteresis,
 which applies to all limits. This register can be written by writing into
 temp1_crit_hyst. Other hysteresis attributes are read-only.
 
+If the BIOS has configured the sensor for automatic temperature management, it
+is likely that it has locked the registers, i.e., that the temperature limits
+cannot be changed.
+
 Sysfs entries
 -------------
 
 temp1_input		Temperature (RO)
-temp1_min		Minimum temperature (RW)
-temp1_max		Maximum temperature (RW)
-temp1_crit		Critical high temperature (RW)
+temp1_min		Minimum temperature (RO or RW)
+temp1_max		Maximum temperature (RO or RW)
+temp1_crit		Critical high temperature (RO or RW)
 
-temp1_crit_hyst		Critical hysteresis temperature (RW)
+temp1_crit_hyst		Critical hysteresis temperature (RO or RW)
 temp1_max_hyst		Maximum hysteresis temperature (RO)
 
 temp1_min_alarm		Temperature low alarm

Documentation/hwmon/k10temp

@@ -9,6 +9,8 @@ Supported chips:
   Socket S1G3: Athlon II, Sempron, Turion II
 * AMD Family 11h processors:
   Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra)
+* AMD Family 12h processors: "Llano"
+* AMD Family 14h processors: "Brazos" (C/E/G-Series)
 
   Prefix: 'k10temp'
   Addresses scanned: PCI space
@@ -17,10 +19,14 @@ Supported chips:
     http://support.amd.com/us/Processor_TechDocs/31116.pdf
   BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors:
     http://support.amd.com/us/Processor_TechDocs/41256.pdf
+  BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors:
+    http://support.amd.com/us/Processor_TechDocs/43170.pdf
   Revision Guide for AMD Family 10h Processors:
     http://support.amd.com/us/Processor_TechDocs/41322.pdf
   Revision Guide for AMD Family 11h Processors:
     http://support.amd.com/us/Processor_TechDocs/41788.pdf
+  Revision Guide for AMD Family 14h Models 00h-0Fh Processors:
+    http://support.amd.com/us/Processor_TechDocs/47534.pdf
   AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks:
     http://support.amd.com/us/Processor_TechDocs/43373.pdf
   AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet:
@@ -34,7 +40,7 @@ Description
 -----------
 
 This driver permits reading of the internal temperature sensor of AMD
-Family 10h and 11h processors.
+Family 10h/11h/12h/14h processors.
 
 All these processors have a sensor, but on those for Socket F or AM2+,
 the sensor may return inconsistent values (erratum 319).  The driver

Documentation/kernel-parameters.txt

@@ -144,6 +144,11 @@ a fixed number of characters. This limit depends on the architecture
 and is between 256 and 4096 characters. It is defined in the file
 ./include/asm/setup.h as COMMAND_LINE_SIZE.
 
+Finally, the [KMG] suffix is commonly described after a number of kernel
+parameter values. These 'K', 'M', and 'G' letters represent the _binary_
+multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30
+bytes respectively. Such letter suffixes can also be entirely omitted.
+
 
 	acpi=		[HW,ACPI,X86]
 			Advanced Configuration and Power Interface
@@ -545,16 +550,20 @@ and is between 256 and 4096 characters. It is defined in the file
 			Format:
 			<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
 
-	crashkernel=nn[KMG]@ss[KMG]
-			[KNL] Reserve a chunk of physical memory to
-			hold a kernel to switch to with kexec on panic.
+	crashkernel=size[KMG][@offset[KMG]]
+			[KNL] Using kexec, Linux can switch to a 'crash kernel'
+			upon panic. This parameter reserves the physical
+			memory region [offset, offset + size] for that kernel
+			image. If '@offset' is omitted, then a suitable offset
+			is selected automatically. Check
+			Documentation/kdump/kdump.txt for further details.
 
 	crashkernel=range1:size1[,range2:size2,...][@offset]
 			[KNL] Same as above, but depends on the memory
 			in the running system. The syntax of range is
 			start-[end] where start and end are both
 			a memory unit (amount[KMG]). See also
-			Documentation/kdump/kdump.txt for a example.
+			Documentation/kdump/kdump.txt for an example.
 
 	cs89x0_dma=	[HW,NET]
 			Format: <dma>
@@ -1262,10 +1271,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			6 (KERN_INFO)		informational
 			7 (KERN_DEBUG)		debug-level messages
 
-	log_buf_len=n	Sets the size of the printk ring buffer, in bytes.
-			Format: { n | nk | nM }
-			n must be a power of two.  The default size
-			is set in the kernel config file.
+	log_buf_len=n[KMG]	Sets the size of the printk ring buffer,
+			in bytes.  n must be a power of two.  The default
+			size is set in the kernel config file.
 
 	logo.nologo	[FB] Disables display of the built-in Linux logo.
 			This may be used to provide more screen space for

Documentation/networking/Makefile

@@ -4,6 +4,8 @@ obj- := dummy.o
 # List of programs to build
 hostprogs-y := ifenslave
 
+HOSTCFLAGS_ifenslave.o += -I$(objtree)/usr/include
+
 # Tell kbuild to always build the programs
 always := $(hostprogs-y)
 

Documentation/workqueue.txt

@@ -190,9 +190,9 @@ resources, scheduled and executed.
 	* Long running CPU intensive workloads which can be better
 	  managed by the system scheduler.
 
-  WQ_FREEZEABLE
+  WQ_FREEZABLE
 
-	A freezeable wq participates in the freeze phase of the system
+	A freezable wq participates in the freeze phase of the system
 	suspend operations.  Work items on the wq are drained and no
 	new work item starts execution until thawed.
 

MAINTAINERS

@@ -885,7 +885,7 @@ S:	Supported
 
 ARM/QUALCOMM MSM MACHINE SUPPORT
 M:	David Brown <davidb@codeaurora.org>
-M:	Daniel Walker <dwalker@codeaurora.org>
+M:	Daniel Walker <dwalker@fifo99.com>
 M:	Bryan Huntsman <bryanh@codeaurora.org>
 L:	linux-arm-msm@vger.kernel.org
 F:	arch/arm/mach-msm/
@@ -2126,6 +2126,7 @@ S:	Supported
 F:	fs/dlm/
 
 DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
+M:	Vinod Koul <vinod.koul@intel.com>
 M:	Dan Williams <dan.j.williams@intel.com>
 S:	Supported
 F:	drivers/dma/
@@ -2774,6 +2775,15 @@ F:	Documentation/isdn/README.gigaset
 F:	drivers/isdn/gigaset/
 F:	include/linux/gigaset_dev.h
 
+GPIO SUBSYSTEM
+M:	Grant Likely <grant.likely@secretlab.ca>
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+T:	git git://git.secretlab.ca/git/linux-2.6.git
+F:	Documentation/gpio/gpio.txt
+F:	drivers/gpio/
+F:	include/linux/gpio*
+
 GRETH 10/100/1G Ethernet MAC device driver
 M:	Kristoffer Glembo <kristoffer@gaisler.com>
 L:	netdev@vger.kernel.org
@@ -2863,7 +2873,6 @@ M:	Guenter Roeck <guenter.roeck@ericsson.com>
 L:	lm-sensors@lm-sensors.org
 W:	http://www.lm-sensors.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-hwmon/
-T:	quilt kernel.org/pub/linux/kernel/people/groeck/linux-staging/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging.git
 S:	Maintained
 F:	Documentation/hwmon/
@@ -4591,7 +4600,7 @@ F:	drivers/i2c/busses/i2c-ocores.c
 
 OPEN FIRMWARE AND FLATTENED DEVICE TREE
 M:	Grant Likely <grant.likely@secretlab.ca>
-L:	devicetree-discuss@lists.ozlabs.org
+L:	devicetree-discuss@lists.ozlabs.org (moderated for non-subscribers)
 W:	http://fdt.secretlab.ca
 T:	git git://git.secretlab.ca/git/linux-2.6.git
 S:	Maintained

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 38
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc6
 NAME = Flesh-Eating Bats with Fangs
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -1177,6 +1177,31 @@ config ARM_ERRATA_743622
 	  visible impact on the overall performance or power consumption of the
 	  processor.
 
+config ARM_ERRATA_751472
+	bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
+	depends on CPU_V7 && SMP
+	help
+	  This option enables the workaround for the 751472 Cortex-A9 (prior
+	  to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
+	  completion of a following broadcasted operation if the second
+	  operation is received by a CPU before the ICIALLUIS has completed,
+	  potentially leading to corrupted entries in the cache or TLB.
+
+config ARM_ERRATA_753970
+	bool "ARM errata: cache sync operation may be faulty"
+	depends on CACHE_PL310
+	help
+	  This option enables the workaround for the 753970 PL310 (r3p0) erratum.
+
+	  Under some condition the effect of cache sync operation on
+	  the store buffer still remains when the operation completes.
+	  This means that the store buffer is always asked to drain and
+	  this prevents it from merging any further writes. The workaround
+	  is to replace the normal offset of cache sync operation (0x730)
+	  by another offset targeting an unmapped PL310 register 0x740.
+	  This has the same effect as the cache sync operation: store buffer
+	  drain and waiting for all buffers empty.
+
 endmenu
 
 source "arch/arm/common/Kconfig"
@@ -1391,7 +1416,7 @@ config AEABI
 
 config OABI_COMPAT
 	bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
-	depends on AEABI && EXPERIMENTAL
+	depends on AEABI && EXPERIMENTAL && !THUMB2_KERNEL
 	default y
 	help
 	  This option preserves the old syscall interface along with the

arch/arm/Makefile

@@ -15,7 +15,7 @@ ifeq ($(CONFIG_CPU_ENDIAN_BE8),y)
 LDFLAGS_vmlinux	+= --be8
 endif
 
-OBJCOPYFLAGS	:=-O binary -R .note -R .note.gnu.build-id -R .comment -S
+OBJCOPYFLAGS	:=-O binary -R .comment -S
 GZFLAGS		:=-9
 #KBUILD_CFLAGS	+=-pipe
 # Explicitly specifiy 32-bit ARM ISA since toolchain default can be -mthumb:

arch/arm/boot/compressed/.gitignore

@@ -1,3 +1,7 @@
 font.c
-piggy.gz
+lib1funcs.S
+piggy.gzip
+piggy.lzo
+piggy.lzma
+vmlinux
 vmlinux.lds

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -36,6 +36,7 @@
 #define L2X0_RAW_INTR_STAT		0x21C
 #define L2X0_INTR_CLEAR			0x220
 #define L2X0_CACHE_SYNC			0x730
+#define L2X0_DUMMY_REG			0x740
 #define L2X0_INV_LINE_PA		0x770
 #define L2X0_INV_WAY			0x77C
 #define L2X0_CLEAN_LINE_PA		0x7B0

arch/arm/include/asm/hardware/sp810.h

@@ -58,6 +58,9 @@
 
 static inline void sysctl_soft_reset(void __iomem *base)
 {
+	/* switch to slow mode */
+	writel(0x2, base + SCCTRL);
+
 	/* writing any value to SCSYSSTAT reg will reset system */
 	writel(0, base + SCSYSSTAT);
 }

arch/arm/include/asm/tlb.h

@@ -18,16 +18,34 @@
 #define __ASMARM_TLB_H
 
 #include <asm/cacheflush.h>
-#include <asm/tlbflush.h>
 
 #ifndef CONFIG_MMU
 
 #include <linux/pagemap.h>
+
+#define tlb_flush(tlb)	((void) tlb)
+
 #include <asm-generic/tlb.h>
 
 #else /* !CONFIG_MMU */
 
+#include <linux/swap.h>
 #include <asm/pgalloc.h>
+#include <asm/tlbflush.h>
+
+/*
+ * We need to delay page freeing for SMP as other CPUs can access pages
+ * which have been removed but not yet had their TLB entries invalidated.
+ * Also, as ARMv7 speculative prefetch can drag new entries into the TLB,
+ * we need to apply this same delaying tactic to ensure correct operation.
+ */
+#if defined(CONFIG_SMP) || defined(CONFIG_CPU_32v7)
+#define tlb_fast_mode(tlb)	0
+#define FREE_PTE_NR		500
+#else
+#define tlb_fast_mode(tlb)	1
+#define FREE_PTE_NR		0
+#endif
 
 /*
  * TLB handling.  This allows us to remove pages from the page
@@ -36,12 +54,58 @@
 struct mmu_gather {
 	struct mm_struct	*mm;
 	unsigned int		fullmm;
+	struct vm_area_struct	*vma;
 	unsigned long		range_start;
 	unsigned long		range_end;
+	unsigned int		nr;
+	struct page		*pages[FREE_PTE_NR];
 };
 
 DECLARE_PER_CPU(struct mmu_gather, mmu_gathers);
 
+/*
+ * This is unnecessarily complex.  There's three ways the TLB shootdown
+ * code is used:
+ *  1. Unmapping a range of vmas.  See zap_page_range(), unmap_region().
+ *     tlb->fullmm = 0, and tlb_start_vma/tlb_end_vma will be called.
+ *     tlb->vma will be non-NULL.
+ *  2. Unmapping all vmas.  See exit_mmap().
+ *     tlb->fullmm = 1, and tlb_start_vma/tlb_end_vma will be called.
+ *     tlb->vma will be non-NULL.  Additionally, page tables will be freed.
+ *  3. Unmapping argument pages.  See shift_arg_pages().
+ *     tlb->fullmm = 0, but tlb_start_vma/tlb_end_vma will not be called.
+ *     tlb->vma will be NULL.
+ */
+static inline void tlb_flush(struct mmu_gather *tlb)
+{
+	if (tlb->fullmm || !tlb->vma)
+		flush_tlb_mm(tlb->mm);
+	else if (tlb->range_end > 0) {
+		flush_tlb_range(tlb->vma, tlb->range_start, tlb->range_end);
+		tlb->range_start = TASK_SIZE;
+		tlb->range_end = 0;
+	}
+}
+
+static inline void tlb_add_flush(struct mmu_gather *tlb, unsigned long addr)
+{
+	if (!tlb->fullmm) {
+		if (addr < tlb->range_start)
+			tlb->range_start = addr;
+		if (addr + PAGE_SIZE > tlb->range_end)
+			tlb->range_end = addr + PAGE_SIZE;
+	}
+}
+
+static inline void tlb_flush_mmu(struct mmu_gather *tlb)
+{
+	tlb_flush(tlb);
+	if (!tlb_fast_mode(tlb)) {
+		free_pages_and_swap_cache(tlb->pages, tlb->nr);
+		tlb->nr = 0;
+	}
+}
+
 static inline struct mmu_gather *
 tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 {
@@ -49,6 +113,8 @@ tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 
 	tlb->mm = mm;
 	tlb->fullmm = full_mm_flush;
+	tlb->vma = NULL;
+	tlb->nr = 0;
 
 	return tlb;
 }
@@ -56,8 +122,7 @@ tlb_gather_mmu(struct mm_struct *mm, unsigned int full_mm_flush)
 static inline void
 tlb_finish_mmu(struct mmu_gather *tlb, unsigned long start, unsigned long end)
 {
-	if (tlb->fullmm)
-		flush_tlb_mm(tlb->mm);
+	tlb_flush_mmu(tlb);
 
 	/* keep the page table cache within bounds */
 	check_pgt_cache();
@@ -71,12 +136,7 @@ tlb_finish_mmu(struct mmu_gather *tlb, unsigned long start, unsigned long end)
 static inline void
 tlb_remove_tlb_entry(struct mmu_gather *tlb, pte_t *ptep, unsigned long addr)
 {
-	if (!tlb->fullmm) {
-		if (addr < tlb->range_start)
-			tlb->range_start = addr;
-		if (addr + PAGE_SIZE > tlb->range_end)
-			tlb->range_end = addr + PAGE_SIZE;
-	}
+	tlb_add_flush(tlb, addr);
 }
 
 /*
@@ -89,6 +149,7 @@ tlb_start_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 {
 	if (!tlb->fullmm) {
 		flush_cache_range(vma, vma->vm_start, vma->vm_end);
+		tlb->vma = vma;
 		tlb->range_start = TASK_SIZE;
 		tlb->range_end = 0;
 	}
@@ -97,12 +158,30 @@ tlb_start_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 static inline void
 tlb_end_vma(struct mmu_gather *tlb, struct vm_area_struct *vma)
 {
-	if (!tlb->fullmm && tlb->range_end > 0)
-		flush_tlb_range(vma, tlb->range_start, tlb->range_end);
+	if (!tlb->fullmm)
+		tlb_flush(tlb);
+}
+
+static inline void tlb_remove_page(struct mmu_gather *tlb, struct page *page)
+{
+	if (tlb_fast_mode(tlb)) {
+		free_page_and_swap_cache(page);
+	} else {
+		tlb->pages[tlb->nr++] = page;
+		if (tlb->nr >= FREE_PTE_NR)
+			tlb_flush_mmu(tlb);
+	}
+}
+
+static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t pte,
+	unsigned long addr)
+{
+	pgtable_page_dtor(pte);
+	tlb_add_flush(tlb, addr);
+	tlb_remove_page(tlb, pte);
 }
 
-#define tlb_remove_page(tlb,page)	free_page_and_swap_cache(page)
-#define pte_free_tlb(tlb, ptep, addr)	pte_free((tlb)->mm, ptep)
+#define pte_free_tlb(tlb, ptep, addr)	__pte_free_tlb(tlb, ptep, addr)
 #define pmd_free_tlb(tlb, pmdp, addr)	pmd_free((tlb)->mm, pmdp)
 
 #define tlb_migrate_finish(mm)		do { } while (0)

arch/arm/include/asm/tlbflush.h

@@ -10,12 +10,7 @@
 #ifndef _ASMARM_TLBFLUSH_H
 #define _ASMARM_TLBFLUSH_H
 
-
-#ifndef CONFIG_MMU
-
-#define tlb_flush(tlb)	((void) tlb)
-
-#else /* CONFIG_MMU */
+#ifdef CONFIG_MMU
 
 #include <asm/glue.h>
 

arch/arm/kernel/head.S

@@ -391,6 +391,7 @@ ENDPROC(__turn_mmu_on)
 
 
 #ifdef CONFIG_SMP_ON_UP
+	__INIT
 __fixup_smp:
 	and	r3, r9, #0x000f0000	@ architecture version
 	teq	r3, #0x000f0000		@ CPU ID supported?
@@ -415,18 +416,7 @@ __fixup_smp_on_up:
 	sub	r3, r0, r3
 	add	r4, r4, r3
 	add	r5, r5, r3
-2:	cmp	r4, r5
-	movhs	pc, lr
-	ldmia	r4!, {r0, r6}
- ARM(	str	r6, [r0, r3]	)
- THUMB(	add	r0, r0, r3	)
-#ifdef __ARMEB__
- THUMB(	mov	r6, r6, ror #16	)	@ Convert word order for big-endian.
-#endif
- THUMB(	strh	r6, [r0], #2	)	@ For Thumb-2, store as two halfwords
- THUMB(	mov	r6, r6, lsr #16	)	@ to be robust against misaligned r3.
- THUMB(	strh	r6, [r0]	)
-	b	2b
+	b	__do_fixup_smp_on_up
 ENDPROC(__fixup_smp)
 
 	.align
@@ -440,7 +430,31 @@ smp_on_up:
 	ALT_SMP(.long	1)
 	ALT_UP(.long	0)
 	.popsection
+#endif
 
+	.text
+__do_fixup_smp_on_up:
+	cmp	r4, r5
+	movhs	pc, lr
+	ldmia	r4!, {r0, r6}
+ ARM(	str	r6, [r0, r3]	)
+ THUMB(	add	r0, r0, r3	)
+#ifdef __ARMEB__
+ THUMB(	mov	r6, r6, ror #16	)	@ Convert word order for big-endian.
 #endif
+ THUMB(	strh	r6, [r0], #2	)	@ For Thumb-2, store as two halfwords
+ THUMB(	mov	r6, r6, lsr #16	)	@ to be robust against misaligned r3.
+ THUMB(	strh	r6, [r0]	)
+	b	__do_fixup_smp_on_up
+ENDPROC(__do_fixup_smp_on_up)
+
+ENTRY(fixup_smp)
+	stmfd	sp!, {r4 - r6, lr}
+	mov	r4, r0
+	add	r5, r0, r1
+	mov	r3, #0
+	bl	__do_fixup_smp_on_up
+	ldmfd	sp!, {r4 - r6, pc}
+ENDPROC(fixup_smp)
 
 #include "head-common.S"

arch/arm/kernel/hw_breakpoint.c

@@ -137,11 +137,10 @@ static u8 get_debug_arch(void)
 	u32 didr;
 
 	/* Do we implement the extended CPUID interface? */
-	if (((read_cpuid_id() >> 16) & 0xf) != 0xf) {
-		pr_warning("CPUID feature registers not supported. "
-				"Assuming v6 debug is present.\n");
+	if (WARN_ONCE((((read_cpuid_id() >> 16) & 0xf) != 0xf),
+	    "CPUID feature registers not supported. "
+	    "Assuming v6 debug is present.\n"))
 		return ARM_DEBUG_ARCH_V6;
-	}
 
 	ARM_DBG_READ(c0, 0, didr);
 	return (didr >> 16) & 0xf;
@@ -152,6 +151,12 @@ u8 arch_get_debug_arch(void)
 	return debug_arch;
 }
 
+static int debug_arch_supported(void)
+{
+	u8 arch = get_debug_arch();
+	return arch >= ARM_DEBUG_ARCH_V6 && arch <= ARM_DEBUG_ARCH_V7_ECP14;
+}
+
 /* Determine number of BRP register available. */
 static int get_num_brp_resources(void)
 {
@@ -268,6 +273,9 @@ out:
 
 int hw_breakpoint_slots(int type)
 {
+	if (!debug_arch_supported())
+		return 0;
+
 	/*
 	 * We can be called early, so don't rely on
 	 * our static variables being initialised.
@@ -834,11 +842,11 @@ static void reset_ctrl_regs(void *unused)
 
 	/*
 	 * v7 debug contains save and restore registers so that debug state
-	 * can be maintained across low-power modes without leaving
-	 * the debug logic powered up. It is IMPLEMENTATION DEFINED whether
-	 * we can write to the debug registers out of reset, so we must
-	 * unlock the OS Lock Access Register to avoid taking undefined
-	 * instruction exceptions later on.
+	 * can be maintained across low-power modes without leaving the debug
+	 * logic powered up. It is IMPLEMENTATION DEFINED whether we can access
+	 * the debug registers out of reset, so we must unlock the OS Lock
+	 * Access Register to avoid taking undefined instruction exceptions
+	 * later on.
 	 */
 	if (debug_arch >= ARM_DEBUG_ARCH_V7_ECP14) {
 		/*
@@ -882,7 +890,7 @@ static int __init arch_hw_breakpoint_init(void)
 
 	debug_arch = get_debug_arch();
 
-	if (debug_arch > ARM_DEBUG_ARCH_V7_ECP14) {
+	if (!debug_arch_supported()) {
 		pr_info("debug architecture 0x%x unsupported.\n", debug_arch);
 		return 0;
 	}
@@ -899,18 +907,18 @@ static int __init arch_hw_breakpoint_init(void)
 		pr_info("%d breakpoint(s) reserved for watchpoint "
 				"single-step.\n", core_num_reserved_brps);
 
+	/*
+	 * Reset the breakpoint resources. We assume that a halting
+	 * debugger will leave the world in a nice state for us.
+	 */
+	on_each_cpu(reset_ctrl_regs, NULL, 1);
+
 	ARM_DBG_READ(c1, 0, dscr);
 	if (dscr & ARM_DSCR_HDBGEN) {
+		max_watchpoint_len = 4;
 		pr_warning("halting debug mode enabled. Assuming maximum "
-				"watchpoint size of 4 bytes.");
+			   "watchpoint size of %u bytes.", max_watchpoint_len);
 	} else {
-		/*
-		 * Reset the breakpoint resources. We assume that a halting
-		 * debugger will leave the world in a nice state for us.
-		 */
-		smp_call_function(reset_ctrl_regs, NULL, 1);
-		reset_ctrl_regs(NULL);
-
 		/* Work out the maximum supported watchpoint length. */
 		max_watchpoint_len = get_max_wp_len();
 		pr_info("maximum watchpoint size is %u bytes.\n",

arch/arm/kernel/kprobes-decode.c

@@ -1437,7 +1437,7 @@ arm_kprobe_decode_insn(kprobe_opcode_t insn, struct arch_specific_insn *asi)
 
 		return space_cccc_1100_010x(insn, asi);
 
-	} else if ((insn & 0x0e000000) == 0x0c400000) {
+	} else if ((insn & 0x0e000000) == 0x0c000000) {
 
 		return space_cccc_110x(insn, asi);
 

arch/arm/kernel/module.c

@@ -22,6 +22,7 @@
 
 #include <asm/pgtable.h>
 #include <asm/sections.h>
+#include <asm/smp_plat.h>
 #include <asm/unwind.h>
 
 #ifdef CONFIG_XIP_KERNEL
@@ -268,12 +269,28 @@ struct mod_unwind_map {
 	const Elf_Shdr *txt_sec;
 };
 
+static const Elf_Shdr *find_mod_section(const Elf32_Ehdr *hdr,
+	const Elf_Shdr *sechdrs, const char *name)
+{
+	const Elf_Shdr *s, *se;
+	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
+
+	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++)
+		if (strcmp(name, secstrs + s->sh_name) == 0)
+			return s;
+
+	return NULL;
+}
+
+extern void fixup_smp(const void *, unsigned long);
+
 int module_finalize(const Elf32_Ehdr *hdr, const Elf_Shdr *sechdrs,
 		    struct module *mod)
 {
+	const Elf_Shdr * __maybe_unused s = NULL;
 #ifdef CONFIG_ARM_UNWIND
 	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
-	const Elf_Shdr *s, *sechdrs_end = sechdrs + hdr->e_shnum;
+	const Elf_Shdr *sechdrs_end = sechdrs + hdr->e_shnum;
 	struct mod_unwind_map maps[ARM_SEC_MAX];
 	int i;
 
@@ -315,6 +332,9 @@ int module_finalize(const Elf32_Ehdr *hdr, const Elf_Shdr *sechdrs,
 					         maps[i].txt_sec->sh_addr,
 					         maps[i].txt_sec->sh_size);
 #endif
+	s = find_mod_section(hdr, sechdrs, ".alt.smp.init");
+	if (s && !is_smp())
+		fixup_smp((void *)s->sh_addr, s->sh_size);
 	return 0;
 }
 

arch/arm/kernel/perf_event.c

@@ -700,7 +700,7 @@ user_backtrace(struct frame_tail __user *tail,
 	 * Frame pointers should strictly progress back up the stack
 	 * (towards higher addresses).
 	 */
-	if (tail >= buftail.fp)
+	if (tail + 1 >= buftail.fp)
 		return NULL;
 
 	return buftail.fp - 1;

arch/arm/kernel/pmu.c

@@ -97,28 +97,34 @@ set_irq_affinity(int irq,
 			   irq, cpu);
 	return err;
 #else
-	return 0;
+	return -EINVAL;
 #endif
 }
 
 static int
 init_cpu_pmu(void)
 {
-	int i, err = 0;
+	int i, irqs, err = 0;
 	struct platform_device *pdev = pmu_devices[ARM_PMU_DEVICE_CPU];
 
-	if (!pdev) {
-		err = -ENODEV;
-		goto out;
-	}
+	if (!pdev)
+		return -ENODEV;
+
+	irqs = pdev->num_resources;
+
+	/*
+	 * If we have a single PMU interrupt that we can't shift, assume that
+	 * we're running on a uniprocessor machine and continue.
+	 */
+	if (irqs == 1 && !irq_can_set_affinity(platform_get_irq(pdev, 0)))
+		return 0;
 
-	for (i = 0; i < pdev->num_resources; ++i) {
+	for (i = 0; i < irqs; ++i) {
 		err = set_irq_affinity(platform_get_irq(pdev, i), i);
 		if (err)
 			break;
 	}
 
-out:
 	return err;
 }
 

arch/arm/kernel/setup.c

@@ -226,8 +226,8 @@ int cpu_architecture(void)
 		 * Register 0 and check for VMSAv7 or PMSAv7 */
 		asm("mrc	p15, 0, %0, c0, c1, 4"
 		    : "=r" (mmfr0));
-		if ((mmfr0 & 0x0000000f) == 0x00000003 ||
-		    (mmfr0 & 0x000000f0) == 0x00000030)
+		if ((mmfr0 & 0x0000000f) >= 0x00000003 ||
+		    (mmfr0 & 0x000000f0) >= 0x00000030)
 			cpu_arch = CPU_ARCH_ARMv7;
 		else if ((mmfr0 & 0x0000000f) == 0x00000002 ||
 			 (mmfr0 & 0x000000f0) == 0x00000020)

arch/arm/kernel/signal.c

@@ -474,7 +474,9 @@ setup_return(struct pt_regs *regs, struct k_sigaction *ka,
 	unsigned long handler = (unsigned long)ka->sa.sa_handler;
 	unsigned long retcode;
 	int thumb = 0;
-	unsigned long cpsr = regs->ARM_cpsr & ~PSR_f;
+	unsigned long cpsr = regs->ARM_cpsr & ~(PSR_f | PSR_E_BIT);
+
+	cpsr |= PSR_ENDSTATE;
 
 	/*
 	 * Maybe we need to deliver a 32-bit signal to a 26-bit task.

arch/arm/kernel/vmlinux.lds.S

@@ -21,6 +21,12 @@
 #define ARM_CPU_KEEP(x)
 #endif
 
+#if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK)
+#define ARM_EXIT_KEEP(x)	x
+#else
+#define ARM_EXIT_KEEP(x)
+#endif
+
 OUTPUT_ARCH(arm)
 ENTRY(stext)
 
@@ -43,6 +49,7 @@ SECTIONS
 		_sinittext = .;
 			HEAD_TEXT
 			INIT_TEXT
+			ARM_EXIT_KEEP(EXIT_TEXT)
 		_einittext = .;
 		ARM_CPU_DISCARD(PROC_INFO)
 		__arch_info_begin = .;
@@ -67,6 +74,7 @@ SECTIONS
 #ifndef CONFIG_XIP_KERNEL
 		__init_begin = _stext;
 		INIT_DATA
+		ARM_EXIT_KEEP(EXIT_DATA)
 #endif
 	}
 
@@ -162,6 +170,7 @@ SECTIONS
 		. = ALIGN(PAGE_SIZE);
 		__init_begin = .;
 		INIT_DATA
+		ARM_EXIT_KEEP(EXIT_DATA)
 		. = ALIGN(PAGE_SIZE);
 		__init_end = .;
 #endif
@@ -247,6 +256,8 @@ SECTIONS
 	}
 #endif
 
+	NOTES
+
 	BSS_SECTION(0, 0, 0)
 	_end = .;
 

arch/arm/mach-pxa/colibri-evalboard.c

@@ -50,7 +50,7 @@ static void __init colibri_mmc_init(void)
 			GPIO0_COLIBRI_PXA270_SD_DETECT;
 	if (machine_is_colibri300())	/* PXA300 Colibri */
 		colibri_mci_platform_data.gpio_card_detect =
-			GPIO39_COLIBRI_PXA300_SD_DETECT;
+			GPIO13_COLIBRI_PXA300_SD_DETECT;
 	else				/* PXA320 Colibri */
 		colibri_mci_platform_data.gpio_card_detect =
 			GPIO28_COLIBRI_PXA320_SD_DETECT;

arch/arm/mach-pxa/colibri-pxa300.c

@@ -41,7 +41,7 @@ static mfp_cfg_t colibri_pxa300_evalboard_pin_config[] __initdata = {
 	GPIO4_MMC1_DAT1,
 	GPIO5_MMC1_DAT2,
 	GPIO6_MMC1_DAT3,
-	GPIO39_GPIO,	/* SD detect */
+	GPIO13_GPIO,	/* GPIO13_COLIBRI_PXA300_SD_DETECT */
 
 	/* UHC */
 	GPIO0_2_USBH_PEN,

arch/arm/mach-pxa/include/mach/colibri.h

@@ -60,7 +60,7 @@ static inline void colibri_pxa3xx_init_nand(void) {}
 #define GPIO113_COLIBRI_PXA270_TS_IRQ	113
 
 /* GPIO definitions for Colibri PXA300/310 */
-#define GPIO39_COLIBRI_PXA300_SD_DETECT	39
+#define GPIO13_COLIBRI_PXA300_SD_DETECT	13
 
 /* GPIO definitions for Colibri PXA320 */
 #define GPIO28_COLIBRI_PXA320_SD_DETECT	28

arch/arm/mach-pxa/palm27x.c

@@ -323,7 +323,7 @@ static struct platform_pwm_backlight_data palm27x_backlight_data = {
 	.pwm_id		= 0,
 	.max_brightness	= 0xfe,
 	.dft_brightness	= 0x7e,
-	.pwm_period_ns	= 3500,
+	.pwm_period_ns	= 3500 * 1024,
 	.init		= palm27x_backlight_init,
 	.notify		= palm27x_backlight_notify,
 	.exit		= palm27x_backlight_exit,

arch/arm/mach-pxa/pm.c

@@ -33,7 +33,7 @@ int pxa_pm_enter(suspend_state_t state)
 #endif
 
 	/* skip registers saving for standby */
-	if (state != PM_SUSPEND_STANDBY) {
+	if (state != PM_SUSPEND_STANDBY && pxa_cpu_pm_fns->save) {
 		pxa_cpu_pm_fns->save(sleep_save);
 		/* before sleeping, calculate and save a checksum */
 		for (i = 0; i < pxa_cpu_pm_fns->save_count - 1; i++)
@@ -44,7 +44,7 @@ int pxa_pm_enter(suspend_state_t state)
 	pxa_cpu_pm_fns->enter(state);
 	cpu_init();
 
-	if (state != PM_SUSPEND_STANDBY) {
+	if (state != PM_SUSPEND_STANDBY && pxa_cpu_pm_fns->restore) {
 		/* after sleeping, validate the checksum */
 		for (i = 0; i < pxa_cpu_pm_fns->save_count - 1; i++)
 			checksum += sleep_save[i];

arch/arm/mach-s5p6442/include/mach/map.h

@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s5p6442/include/mach/map.h
  *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
  * S5P6442 - Memory map definitions
@@ -16,56 +16,61 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5P6442_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5P6442_PA_CHIPID
+#define S5P6442_PA_SDRAM	0x20000000
 
-#define S5P6442_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5P6442_PA_SYSCON
+#define S5P6442_PA_I2S0		0xC0B00000
+#define S5P6442_PA_I2S1		0xF2200000
 
-#define S5P6442_PA_GPIO		(0xE0200000)
+#define S5P6442_PA_CHIPID	0xE0000000
 
-#define S5P6442_PA_VIC0		(0xE4000000)
-#define S5P6442_PA_VIC1		(0xE4100000)
-#define S5P6442_PA_VIC2		(0xE4200000)
+#define S5P6442_PA_SYSCON	0xE0100000
 
-#define S5P6442_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5P6442_PA_SROMC
+#define S5P6442_PA_GPIO		0xE0200000
 
-#define S5P6442_PA_MDMA		0xE8000000
-#define S5P6442_PA_PDMA		0xE9000000
+#define S5P6442_PA_VIC0		0xE4000000
+#define S5P6442_PA_VIC1		0xE4100000
+#define S5P6442_PA_VIC2		0xE4200000
 
-#define S5P6442_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5P6442_PA_TIMER
+#define S5P6442_PA_SROMC	0xE7000000
 
-#define S5P6442_PA_SYSTIMER   	(0xEA100000)
+#define S5P6442_PA_MDMA		0xE8000000
+#define S5P6442_PA_PDMA		0xE9000000
 
-#define S5P6442_PA_WATCHDOG	(0xEA200000)
+#define S5P6442_PA_TIMER	0xEA000000
 
-#define S5P6442_PA_UART		(0xEC000000)
+#define S5P6442_PA_SYSTIMER	0xEA100000
 
-#define S5P_PA_UART0		(S5P6442_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5P6442_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5P6442_PA_UART + 0x800)
-#define S5P_SZ_UART		SZ_256
+#define S5P6442_PA_WATCHDOG	0xEA200000
 
-#define S5P6442_PA_IIC0		(0xEC100000)
+#define S5P6442_PA_UART		0xEC000000
 
-#define S5P6442_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5P6442_PA_SDRAM
+#define S5P6442_PA_IIC0		0xEC100000
 
 #define S5P6442_PA_SPI		0xEC300000
 
-/* I2S */
-#define S5P6442_PA_I2S0		0xC0B00000
-#define S5P6442_PA_I2S1		0xF2200000
-
-/* PCM */
 #define S5P6442_PA_PCM0		0xF2400000
 #define S5P6442_PA_PCM1		0xF2500000
 
-/* compatibiltiy defines. */
+/* Compatibiltiy Defines */
+
+#define S3C_PA_IIC		S5P6442_PA_IIC0
 #define S3C_PA_WDT		S5P6442_PA_WATCHDOG
+
+#define S5P_PA_CHIPID		S5P6442_PA_CHIPID
+#define S5P_PA_SDRAM		S5P6442_PA_SDRAM
+#define S5P_PA_SROMC		S5P6442_PA_SROMC
+#define S5P_PA_SYSCON		S5P6442_PA_SYSCON
+#define S5P_PA_TIMER		S5P6442_PA_TIMER
+
+/* UART */
+
 #define S3C_PA_UART		S5P6442_PA_UART
-#define S3C_PA_IIC		S5P6442_PA_IIC0
+
+#define S5P_PA_UART(x)		(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0		S5P_PA_UART(0)
+#define S5P_PA_UART1		S5P_PA_UART(1)
+#define S5P_PA_UART2		S5P_PA_UART(2)
+
+#define S5P_SZ_UART		SZ_256
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5p64x0/include/mach/map.h

@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s5p64x0/include/mach/map.h
  *
- * Copyright (c) 2009-2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2009-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
  * S5P64X0 - Memory map definitions
@@ -16,64 +16,46 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5P64X0_PA_SDRAM	(0x20000000)
+#define S5P64X0_PA_SDRAM	0x20000000
 
-#define S5P64X0_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5P64X0_PA_CHIPID
-
-#define S5P64X0_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5P64X0_PA_SYSCON
-
-#define S5P64X0_PA_GPIO		(0xE0308000)
-
-#define S5P64X0_PA_VIC0		(0xE4000000)
-#define S5P64X0_PA_VIC1		(0xE4100000)
+#define S5P64X0_PA_CHIPID	0xE0000000
 
-#define S5P64X0_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5P64X0_PA_SROMC
-
-#define S5P64X0_PA_PDMA		(0xE9000000)
-
-#define S5P64X0_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5P64X0_PA_TIMER
+#define S5P64X0_PA_SYSCON	0xE0100000
 
-#define S5P64X0_PA_RTC		(0xEA100000)
+#define S5P64X0_PA_GPIO		0xE0308000
 
-#define S5P64X0_PA_WDT		(0xEA200000)
+#define S5P64X0_PA_VIC0		0xE4000000
+#define S5P64X0_PA_VIC1		0xE4100000
 
-#define S5P6440_PA_UART(x)	(0xEC000000 + ((x) * S3C_UART_OFFSET))
-#define S5P6450_PA_UART(x)	((x < 5) ? (0xEC800000 + ((x) * S3C_UART_OFFSET)) : (0xEC000000))
+#define S5P64X0_PA_SROMC	0xE7000000
 
-#define S5P_PA_UART0		S5P6450_PA_UART(0)
-#define S5P_PA_UART1		S5P6450_PA_UART(1)
-#define S5P_PA_UART2		S5P6450_PA_UART(2)
-#define S5P_PA_UART3		S5P6450_PA_UART(3)
-#define S5P_PA_UART4		S5P6450_PA_UART(4)
-#define S5P_PA_UART5		S5P6450_PA_UART(5)
+#define S5P64X0_PA_PDMA		0xE9000000
 
-#define S5P_SZ_UART		SZ_256
+#define S5P64X0_PA_TIMER	0xEA000000
+#define S5P64X0_PA_RTC		0xEA100000
+#define S5P64X0_PA_WDT		0xEA200000
 
-#define S5P6440_PA_IIC0		(0xEC104000)
-#define S5P6440_PA_IIC1		(0xEC20F000)
-#define S5P6450_PA_IIC0		(0xEC100000)
-#define S5P6450_PA_IIC1		(0xEC200000)
+#define S5P6440_PA_IIC0		0xEC104000
+#define S5P6440_PA_IIC1		0xEC20F000
+#define S5P6450_PA_IIC0		0xEC100000
+#define S5P6450_PA_IIC1		0xEC200000
 
-#define S5P64X0_PA_SPI0		(0xEC400000)
-#define S5P64X0_PA_SPI1		(0xEC500000)
+#define S5P64X0_PA_SPI0		0xEC400000
+#define S5P64X0_PA_SPI1		0xEC500000
 
-#define S5P64X0_PA_HSOTG	(0xED100000)
+#define S5P64X0_PA_HSOTG	0xED100000
 
 #define S5P64X0_PA_HSMMC(x)	(0xED800000 + ((x) * 0x100000))
 
-#define S5P64X0_PA_I2S		(0xF2000000)
+#define S5P64X0_PA_I2S		0xF2000000
 #define S5P6450_PA_I2S1		0xF2800000
 #define S5P6450_PA_I2S2		0xF2900000
 
-#define S5P64X0_PA_PCM		(0xF2100000)
+#define S5P64X0_PA_PCM		0xF2100000
 
-#define S5P64X0_PA_ADC		(0xF3000000)
+#define S5P64X0_PA_ADC		0xF3000000
 
-/* compatibiltiy defines. */
+/* Compatibiltiy Defines */
 
 #define S3C_PA_HSMMC0		S5P64X0_PA_HSMMC(0)
 #define S3C_PA_HSMMC1		S5P64X0_PA_HSMMC(1)
@@ -83,6 +65,25 @@
 #define S3C_PA_RTC		S5P64X0_PA_RTC
 #define S3C_PA_WDT		S5P64X0_PA_WDT
 
+#define S5P_PA_CHIPID		S5P64X0_PA_CHIPID
+#define S5P_PA_SROMC		S5P64X0_PA_SROMC
+#define S5P_PA_SYSCON		S5P64X0_PA_SYSCON
+#define S5P_PA_TIMER		S5P64X0_PA_TIMER
+
 #define SAMSUNG_PA_ADC		S5P64X0_PA_ADC
 
+/* UART */
+
+#define S5P6440_PA_UART(x)	(0xEC000000 + ((x) * S3C_UART_OFFSET))
+#define S5P6450_PA_UART(x)	((x < 5) ? (0xEC800000 + ((x) * S3C_UART_OFFSET)) : (0xEC000000))
+
+#define S5P_PA_UART0		S5P6450_PA_UART(0)
+#define S5P_PA_UART1		S5P6450_PA_UART(1)
+#define S5P_PA_UART2		S5P6450_PA_UART(2)
+#define S5P_PA_UART3		S5P6450_PA_UART(3)
+#define S5P_PA_UART4		S5P6450_PA_UART(4)
+#define S5P_PA_UART5		S5P6450_PA_UART(5)
+
+#define S5P_SZ_UART		SZ_256
+
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pc100/include/mach/map.h

@@ -1,4 +1,7 @@
 /* linux/arch/arm/mach-s5pc100/include/mach/map.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
  *
  * Copyright 2009 Samsung Electronics Co.
  *	Byungho Min <bhmin@samsung.com>
@@ -16,145 +19,115 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-/*
- * map-base.h has already defined virtual memory address
- * S3C_VA_IRQ		S3C_ADDR(0x00000000)	irq controller(s)
- * S3C_VA_SYS		S3C_ADDR(0x00100000)	system control
- * S3C_VA_MEM		S3C_ADDR(0x00200000)	system control (not used)
- * S3C_VA_TIMER		S3C_ADDR(0x00300000)	timer block
- * S3C_VA_WATCHDOG	S3C_ADDR(0x00400000)	watchdog
- * S3C_VA_UART		S3C_ADDR(0x01000000)	UART
- *
- * S5PC100 specific virtual memory address can be defined here
- * S5PC1XX_VA_GPIO	S3C_ADDR(0x00500000)	GPIO
- *
- */
+#define S5PC100_PA_SDRAM		0x20000000
+
+#define S5PC100_PA_ONENAND		0xE7100000
+#define S5PC100_PA_ONENAND_BUF		0xB0000000
+
+#define S5PC100_PA_CHIPID		0xE0000000
 
-#define S5PC100_PA_ONENAND_BUF	(0xB0000000)
-#define S5PC100_SZ_ONENAND_BUF	(SZ_256M - SZ_32M)
+#define S5PC100_PA_SYSCON		0xE0100000
 
-/* Chip ID */
+#define S5PC100_PA_OTHERS		0xE0200000
 
-#define S5PC100_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5PC100_PA_CHIPID
+#define S5PC100_PA_GPIO			0xE0300000
 
-#define S5PC100_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5PC100_PA_SYSCON
+#define S5PC100_PA_VIC0			0xE4000000
+#define S5PC100_PA_VIC1			0xE4100000
+#define S5PC100_PA_VIC2			0xE4200000
 
-#define S5PC100_PA_OTHERS	(0xE0200000)
-#define S5PC100_VA_OTHERS	(S3C_VA_SYS + 0x10000)
+#define S5PC100_PA_SROMC		0xE7000000
 
-#define S5PC100_PA_GPIO		(0xE0300000)
-#define S5PC1XX_VA_GPIO		S3C_ADDR(0x00500000)
+#define S5PC100_PA_CFCON		0xE7800000
 
-/* Interrupt */
-#define S5PC100_PA_VIC0		(0xE4000000)
-#define S5PC100_PA_VIC1		(0xE4100000)
-#define S5PC100_PA_VIC2		(0xE4200000)
-#define S5PC100_VA_VIC		S3C_VA_IRQ
-#define S5PC100_VA_VIC_OFFSET	0x10000
-#define S5PC1XX_VA_VIC(x)	(S5PC100_VA_VIC + ((x) * S5PC100_VA_VIC_OFFSET))
+#define S5PC100_PA_MDMA			0xE8100000
+#define S5PC100_PA_PDMA0		0xE9000000
+#define S5PC100_PA_PDMA1		0xE9200000
 
-#define S5PC100_PA_SROMC	(0xE7000000)
-#define S5P_PA_SROMC		S5PC100_PA_SROMC
+#define S5PC100_PA_TIMER		0xEA000000
+#define S5PC100_PA_SYSTIMER		0xEA100000
+#define S5PC100_PA_WATCHDOG		0xEA200000
+#define S5PC100_PA_RTC			0xEA300000
 
-#define S5PC100_PA_ONENAND	(0xE7100000)
+#define S5PC100_PA_UART			0xEC000000
 
-#define S5PC100_PA_CFCON	(0xE7800000)
+#define S5PC100_PA_IIC0			0xEC100000
+#define S5PC100_PA_IIC1			0xEC200000
 
-/* DMA */
-#define S5PC100_PA_MDMA		(0xE8100000)
-#define S5PC100_PA_PDMA0	(0xE9000000)
-#define S5PC100_PA_PDMA1	(0xE9200000)
+#define S5PC100_PA_SPI0			0xEC300000
+#define S5PC100_PA_SPI1			0xEC400000
+#define S5PC100_PA_SPI2			0xEC500000
 
-/* Timer */
-#define S5PC100_PA_TIMER	(0xEA000000)
-#define S5P_PA_TIMER		S5PC100_PA_TIMER
+#define S5PC100_PA_USB_HSOTG		0xED200000
+#define S5PC100_PA_USB_HSPHY		0xED300000
 
-#define S5PC100_PA_SYSTIMER	(0xEA100000)
+#define S5PC100_PA_HSMMC(x)		(0xED800000 + ((x) * 0x100000))
 
-#define S5PC100_PA_WATCHDOG	(0xEA200000)
-#define S5PC100_PA_RTC		(0xEA300000)
+#define S5PC100_PA_FB			0xEE000000
 
-#define S5PC100_PA_UART		(0xEC000000)
+#define S5PC100_PA_FIMC0		0xEE200000
+#define S5PC100_PA_FIMC1		0xEE300000
+#define S5PC100_PA_FIMC2		0xEE400000
 
-#define S5P_PA_UART0		(S5PC100_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5PC100_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5PC100_PA_UART + 0x800)
-#define S5P_PA_UART3		(S5PC100_PA_UART + 0xC00)
-#define S5P_SZ_UART		SZ_256
+#define S5PC100_PA_I2S0			0xF2000000
+#define S5PC100_PA_I2S1			0xF2100000
+#define S5PC100_PA_I2S2			0xF2200000
 
-#define S5PC100_PA_IIC0		(0xEC100000)
-#define S5PC100_PA_IIC1		(0xEC200000)
+#define S5PC100_PA_AC97			0xF2300000
 
-/* SPI */
-#define S5PC100_PA_SPI0		0xEC300000
-#define S5PC100_PA_SPI1		0xEC400000
-#define S5PC100_PA_SPI2		0xEC500000
+#define S5PC100_PA_PCM0			0xF2400000
+#define S5PC100_PA_PCM1			0xF2500000
 
-/* USB HS OTG */
-#define S5PC100_PA_USB_HSOTG	(0xED200000)
-#define S5PC100_PA_USB_HSPHY	(0xED300000)
+#define S5PC100_PA_SPDIF		0xF2600000
 
-#define S5PC100_PA_FB		(0xEE000000)
+#define S5PC100_PA_TSADC		0xF3000000
 
-#define S5PC100_PA_FIMC0	(0xEE200000)
-#define S5PC100_PA_FIMC1	(0xEE300000)
-#define S5PC100_PA_FIMC2	(0xEE400000)
+#define S5PC100_PA_KEYPAD		0xF3100000
 
-#define S5PC100_PA_I2S0		(0xF2000000)
-#define S5PC100_PA_I2S1		(0xF2100000)
-#define S5PC100_PA_I2S2		(0xF2200000)
+/* Compatibiltiy Defines */
 
-#define S5PC100_PA_AC97		0xF2300000
+#define S3C_PA_FB			S5PC100_PA_FB
+#define S3C_PA_HSMMC0			S5PC100_PA_HSMMC(0)
+#define S3C_PA_HSMMC1			S5PC100_PA_HSMMC(1)
+#define S3C_PA_HSMMC2			S5PC100_PA_HSMMC(2)
+#define S3C_PA_IIC			S5PC100_PA_IIC0
+#define S3C_PA_IIC1			S5PC100_PA_IIC1
+#define S3C_PA_KEYPAD			S5PC100_PA_KEYPAD
+#define S3C_PA_ONENAND			S5PC100_PA_ONENAND
+#define S3C_PA_ONENAND_BUF		S5PC100_PA_ONENAND_BUF
+#define S3C_PA_RTC			S5PC100_PA_RTC
+#define S3C_PA_TSADC			S5PC100_PA_TSADC
+#define S3C_PA_USB_HSOTG		S5PC100_PA_USB_HSOTG
+#define S3C_PA_USB_HSPHY		S5PC100_PA_USB_HSPHY
+#define S3C_PA_WDT			S5PC100_PA_WATCHDOG
 
-/* PCM */
-#define S5PC100_PA_PCM0		0xF2400000
-#define S5PC100_PA_PCM1		0xF2500000
+#define S5P_PA_CHIPID			S5PC100_PA_CHIPID
+#define S5P_PA_FIMC0			S5PC100_PA_FIMC0
+#define S5P_PA_FIMC1			S5PC100_PA_FIMC1
+#define S5P_PA_FIMC2			S5PC100_PA_FIMC2
+#define S5P_PA_SDRAM			S5PC100_PA_SDRAM
+#define S5P_PA_SROMC			S5PC100_PA_SROMC
+#define S5P_PA_SYSCON			S5PC100_PA_SYSCON
+#define S5P_PA_TIMER			S5PC100_PA_TIMER
 
-#define S5PC100_PA_SPDIF	0xF2600000
+#define SAMSUNG_PA_ADC			S5PC100_PA_TSADC
+#define SAMSUNG_PA_CFCON		S5PC100_PA_CFCON
+#define SAMSUNG_PA_KEYPAD		S5PC100_PA_KEYPAD
 
-#define S5PC100_PA_TSADC	(0xF3000000)
+#define S5PC100_VA_OTHERS		(S3C_VA_SYS + 0x10000)
 
-/* KEYPAD */
-#define S5PC100_PA_KEYPAD	(0xF3100000)
+#define S3C_SZ_ONENAND_BUF		(SZ_256M - SZ_32M)
 
-#define S5PC100_PA_HSMMC(x)	(0xED800000 + ((x) * 0x100000))
+/* UART */
 
-#define S5PC100_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5PC100_PA_SDRAM
+#define S3C_PA_UART			S5PC100_PA_UART
 
-/* compatibiltiy defines. */
-#define S3C_PA_UART		S5PC100_PA_UART
-#define S3C_PA_IIC		S5PC100_PA_IIC0
-#define S3C_PA_IIC1		S5PC100_PA_IIC1
-#define S3C_PA_FB		S5PC100_PA_FB
-#define S3C_PA_G2D		S5PC100_PA_G2D
-#define S3C_PA_G3D		S5PC100_PA_G3D
-#define S3C_PA_JPEG		S5PC100_PA_JPEG
-#define S3C_PA_ROTATOR		S5PC100_PA_ROTATOR
-#define S5P_VA_VIC0		S5PC1XX_VA_VIC(0)
-#define S5P_VA_VIC1		S5PC1XX_VA_VIC(1)
-#define S5P_VA_VIC2		S5PC1XX_VA_VIC(2)
-#define S3C_PA_USB_HSOTG	S5PC100_PA_USB_HSOTG
-#define S3C_PA_USB_HSPHY	S5PC100_PA_USB_HSPHY
-#define S3C_PA_HSMMC0		S5PC100_PA_HSMMC(0)
-#define S3C_PA_HSMMC1		S5PC100_PA_HSMMC(1)
-#define S3C_PA_HSMMC2		S5PC100_PA_HSMMC(2)
-#define S3C_PA_KEYPAD		S5PC100_PA_KEYPAD
-#define S3C_PA_WDT		S5PC100_PA_WATCHDOG
-#define S3C_PA_TSADC		S5PC100_PA_TSADC
-#define S3C_PA_ONENAND		S5PC100_PA_ONENAND
-#define S3C_PA_ONENAND_BUF	S5PC100_PA_ONENAND_BUF
-#define S3C_SZ_ONENAND_BUF	S5PC100_SZ_ONENAND_BUF
-#define S3C_PA_RTC		S5PC100_PA_RTC
-
-#define SAMSUNG_PA_ADC		S5PC100_PA_TSADC
-#define SAMSUNG_PA_CFCON	S5PC100_PA_CFCON
-#define SAMSUNG_PA_KEYPAD	S5PC100_PA_KEYPAD
+#define S5P_PA_UART(x)			(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0			S5P_PA_UART(0)
+#define S5P_PA_UART1			S5P_PA_UART(1)
+#define S5P_PA_UART2			S5P_PA_UART(2)
+#define S5P_PA_UART3			S5P_PA_UART(3)
 
-#define S5P_PA_FIMC0		S5PC100_PA_FIMC0
-#define S5P_PA_FIMC1		S5PC100_PA_FIMC1
-#define S5P_PA_FIMC2		S5PC100_PA_FIMC2
+#define S5P_SZ_UART			SZ_256
 
-#endif /* __ASM_ARCH_C100_MAP_H */
+#endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pv210/include/mach/map.h

@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s5pv210/include/mach/map.h
  *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
  * S5PV210 - Memory map definitions
@@ -16,122 +16,120 @@
 #include <plat/map-base.h>
 #include <plat/map-s5p.h>
 
-#define S5PV210_PA_SROM_BANK5	(0xA8000000)
+#define S5PV210_PA_SDRAM		0x20000000
 
-#define S5PC110_PA_ONENAND	(0xB0000000)
-#define S5P_PA_ONENAND		S5PC110_PA_ONENAND
+#define S5PV210_PA_SROM_BANK5		0xA8000000
 
-#define S5PC110_PA_ONENAND_DMA	(0xB0600000)
-#define S5P_PA_ONENAND_DMA	S5PC110_PA_ONENAND_DMA
+#define S5PC110_PA_ONENAND		0xB0000000
+#define S5PC110_PA_ONENAND_DMA		0xB0600000
 
-#define S5PV210_PA_CHIPID	(0xE0000000)
-#define S5P_PA_CHIPID		S5PV210_PA_CHIPID
+#define S5PV210_PA_CHIPID		0xE0000000
 
-#define S5PV210_PA_SYSCON	(0xE0100000)
-#define S5P_PA_SYSCON		S5PV210_PA_SYSCON
+#define S5PV210_PA_SYSCON		0xE0100000
 
-#define S5PV210_PA_GPIO		(0xE0200000)
+#define S5PV210_PA_GPIO			0xE0200000
 
-/* SPI */
-#define S5PV210_PA_SPI0		0xE1300000
-#define S5PV210_PA_SPI1		0xE1400000
+#define S5PV210_PA_SPDIF		0xE1100000
 
-#define S5PV210_PA_KEYPAD	(0xE1600000)
+#define S5PV210_PA_SPI0			0xE1300000
+#define S5PV210_PA_SPI1			0xE1400000
 
-#define S5PV210_PA_IIC0		(0xE1800000)
-#define S5PV210_PA_IIC1		(0xFAB00000)
-#define S5PV210_PA_IIC2		(0xE1A00000)
+#define S5PV210_PA_KEYPAD		0xE1600000
 
-#define S5PV210_PA_TIMER	(0xE2500000)
-#define S5P_PA_TIMER		S5PV210_PA_TIMER
+#define S5PV210_PA_ADC			0xE1700000
 
-#define S5PV210_PA_SYSTIMER	(0xE2600000)
+#define S5PV210_PA_IIC0			0xE1800000
+#define S5PV210_PA_IIC1			0xFAB00000
+#define S5PV210_PA_IIC2			0xE1A00000
 
-#define S5PV210_PA_WATCHDOG	(0xE2700000)
+#define S5PV210_PA_AC97			0xE2200000
 
-#define S5PV210_PA_RTC		(0xE2800000)
-#define S5PV210_PA_UART		(0xE2900000)
+#define S5PV210_PA_PCM0			0xE2300000
+#define S5PV210_PA_PCM1			0xE1200000
+#define S5PV210_PA_PCM2			0xE2B00000
 
-#define S5P_PA_UART0		(S5PV210_PA_UART + 0x0)
-#define S5P_PA_UART1		(S5PV210_PA_UART + 0x400)
-#define S5P_PA_UART2		(S5PV210_PA_UART + 0x800)
-#define S5P_PA_UART3		(S5PV210_PA_UART + 0xC00)
+#define S5PV210_PA_TIMER		0xE2500000
+#define S5PV210_PA_SYSTIMER		0xE2600000
+#define S5PV210_PA_WATCHDOG		0xE2700000
+#define S5PV210_PA_RTC			0xE2800000
 
-#define S5P_SZ_UART		SZ_256
+#define S5PV210_PA_UART			0xE2900000
 
-#define S3C_VA_UARTx(x)		(S3C_VA_UART + ((x) * S3C_UART_OFFSET))
+#define S5PV210_PA_SROMC		0xE8000000
 
-#define S5PV210_PA_SROMC	(0xE8000000)
-#define S5P_PA_SROMC		S5PV210_PA_SROMC
+#define S5PV210_PA_CFCON		0xE8200000
 
-#define S5PV210_PA_CFCON	(0xE8200000)
+#define S5PV210_PA_HSMMC(x)		(0xEB000000 + ((x) * 0x100000))
 
-#define S5PV210_PA_MDMA		0xFA200000
-#define S5PV210_PA_PDMA0	0xE0900000
-#define S5PV210_PA_PDMA1	0xE0A00000
+#define S5PV210_PA_HSOTG		0xEC000000
+#define S5PV210_PA_HSPHY		0xEC100000
 
-#define S5PV210_PA_FB		(0xF8000000)
+#define S5PV210_PA_IIS0			0xEEE30000
+#define S5PV210_PA_IIS1			0xE2100000
+#define S5PV210_PA_IIS2			0xE2A00000
 
-#define S5PV210_PA_FIMC0	(0xFB200000)
-#define S5PV210_PA_FIMC1	(0xFB300000)
-#define S5PV210_PA_FIMC2	(0xFB400000)
+#define S5PV210_PA_DMC0			0xF0000000
+#define S5PV210_PA_DMC1			0xF1400000
 
-#define S5PV210_PA_HSMMC(x)	(0xEB000000 + ((x) * 0x100000))
+#define S5PV210_PA_VIC0			0xF2000000
+#define S5PV210_PA_VIC1			0xF2100000
+#define S5PV210_PA_VIC2			0xF2200000
+#define S5PV210_PA_VIC3			0xF2300000
 
-#define S5PV210_PA_HSOTG	(0xEC000000)
-#define S5PV210_PA_HSPHY	(0xEC100000)
+#define S5PV210_PA_FB			0xF8000000
 
-#define S5PV210_PA_VIC0		(0xF2000000)
-#define S5PV210_PA_VIC1		(0xF2100000)
-#define S5PV210_PA_VIC2		(0xF2200000)
-#define S5PV210_PA_VIC3		(0xF2300000)
+#define S5PV210_PA_MDMA			0xFA200000
+#define S5PV210_PA_PDMA0		0xE0900000
+#define S5PV210_PA_PDMA1		0xE0A00000
 
-#define S5PV210_PA_SDRAM	(0x20000000)
-#define S5P_PA_SDRAM		S5PV210_PA_SDRAM
+#define S5PV210_PA_MIPI_CSIS		0xFA600000
 
-/* S/PDIF */
-#define S5PV210_PA_SPDIF	0xE1100000
+#define S5PV210_PA_FIMC0		0xFB200000
+#define S5PV210_PA_FIMC1		0xFB300000
+#define S5PV210_PA_FIMC2		0xFB400000
 
-/* I2S */
-#define S5PV210_PA_IIS0		0xEEE30000
-#define S5PV210_PA_IIS1		0xE2100000
-#define S5PV210_PA_IIS2		0xE2A00000
+/* Compatibiltiy Defines */
 
-/* PCM */
-#define S5PV210_PA_PCM0		0xE2300000
-#define S5PV210_PA_PCM1		0xE1200000
-#define S5PV210_PA_PCM2		0xE2B00000
+#define S3C_PA_FB			S5PV210_PA_FB
+#define S3C_PA_HSMMC0			S5PV210_PA_HSMMC(0)
+#define S3C_PA_HSMMC1			S5PV210_PA_HSMMC(1)
+#define S3C_PA_HSMMC2			S5PV210_PA_HSMMC(2)
+#define S3C_PA_HSMMC3			S5PV210_PA_HSMMC(3)
+#define S3C_PA_IIC			S5PV210_PA_IIC0
+#define S3C_PA_IIC1			S5PV210_PA_IIC1
+#define S3C_PA_IIC2			S5PV210_PA_IIC2
+#define S3C_PA_RTC			S5PV210_PA_RTC
+#define S3C_PA_USB_HSOTG		S5PV210_PA_HSOTG
+#define S3C_PA_WDT			S5PV210_PA_WATCHDOG
 
-/* AC97 */
-#define S5PV210_PA_AC97		0xE2200000
+#define S5P_PA_CHIPID			S5PV210_PA_CHIPID
+#define S5P_PA_FIMC0			S5PV210_PA_FIMC0
+#define S5P_PA_FIMC1			S5PV210_PA_FIMC1
+#define S5P_PA_FIMC2			S5PV210_PA_FIMC2
+#define S5P_PA_MIPI_CSIS0		S5PV210_PA_MIPI_CSIS
+#define S5P_PA_ONENAND			S5PC110_PA_ONENAND
+#define S5P_PA_ONENAND_DMA		S5PC110_PA_ONENAND_DMA
+#define S5P_PA_SDRAM			S5PV210_PA_SDRAM
+#define S5P_PA_SROMC			S5PV210_PA_SROMC
+#define S5P_PA_SYSCON			S5PV210_PA_SYSCON
+#define S5P_PA_TIMER			S5PV210_PA_TIMER
 
-#define S5PV210_PA_ADC		(0xE1700000)
+#define SAMSUNG_PA_ADC			S5PV210_PA_ADC
+#define SAMSUNG_PA_CFCON		S5PV210_PA_CFCON
+#define SAMSUNG_PA_KEYPAD		S5PV210_PA_KEYPAD
 
-#define S5PV210_PA_DMC0		(0xF0000000)
-#define S5PV210_PA_DMC1		(0xF1400000)
+/* UART */
 
-#define S5PV210_PA_MIPI_CSIS	0xFA600000
+#define S3C_VA_UARTx(x)			(S3C_VA_UART + ((x) * S3C_UART_OFFSET))
 
-/* compatibiltiy defines. */
-#define S3C_PA_UART		S5PV210_PA_UART
-#define S3C_PA_HSMMC0		S5PV210_PA_HSMMC(0)
-#define S3C_PA_HSMMC1		S5PV210_PA_HSMMC(1)
-#define S3C_PA_HSMMC2		S5PV210_PA_HSMMC(2)
-#define S3C_PA_HSMMC3		S5PV210_PA_HSMMC(3)
-#define S3C_PA_IIC		S5PV210_PA_IIC0
-#define S3C_PA_IIC1		S5PV210_PA_IIC1
-#define S3C_PA_IIC2		S5PV210_PA_IIC2
-#define S3C_PA_FB		S5PV210_PA_FB
-#define S3C_PA_RTC		S5PV210_PA_RTC
-#define S3C_PA_WDT		S5PV210_PA_WATCHDOG
-#define S3C_PA_USB_HSOTG	S5PV210_PA_HSOTG
-#define S5P_PA_FIMC0		S5PV210_PA_FIMC0
-#define S5P_PA_FIMC1		S5PV210_PA_FIMC1
-#define S5P_PA_FIMC2		S5PV210_PA_FIMC2
-#define S5P_PA_MIPI_CSIS0	S5PV210_PA_MIPI_CSIS
+#define S3C_PA_UART			S5PV210_PA_UART
 
-#define SAMSUNG_PA_ADC		S5PV210_PA_ADC
-#define SAMSUNG_PA_CFCON	S5PV210_PA_CFCON
-#define SAMSUNG_PA_KEYPAD	S5PV210_PA_KEYPAD
+#define S5P_PA_UART(x)			(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0			S5P_PA_UART(0)
+#define S5P_PA_UART1			S5P_PA_UART(1)
+#define S5P_PA_UART2			S5P_PA_UART(2)
+#define S5P_PA_UART3			S5P_PA_UART(3)
+
+#define S5P_SZ_UART			SZ_256
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pv210/mach-aquila.c

@@ -149,7 +149,7 @@ static struct regulator_init_data aquila_ldo2_data = {
 
 static struct regulator_init_data aquila_ldo3_data = {
 	.constraints	= {
-		.name		= "VUSB/MIPI_1.1V",
+		.name		= "VUSB+MIPI_1.1V",
 		.min_uV		= 1100000,
 		.max_uV		= 1100000,
 		.apply_uV	= 1,
@@ -197,7 +197,7 @@ static struct regulator_init_data aquila_ldo7_data = {
 
 static struct regulator_init_data aquila_ldo8_data = {
 	.constraints	= {
-		.name		= "VUSB/VADC_3.3V",
+		.name		= "VUSB+VADC_3.3V",
 		.min_uV		= 3300000,
 		.max_uV		= 3300000,
 		.apply_uV	= 1,
@@ -207,7 +207,7 @@ static struct regulator_init_data aquila_ldo8_data = {
 
 static struct regulator_init_data aquila_ldo9_data = {
 	.constraints	= {
-		.name		= "VCC/VCAM_2.8V",
+		.name		= "VCC+VCAM_2.8V",
 		.min_uV		= 2800000,
 		.max_uV		= 2800000,
 		.apply_uV	= 1,
@@ -381,9 +381,12 @@ static struct max8998_platform_data aquila_max8998_pdata = {
 	.buck1_set1	= S5PV210_GPH0(3),
 	.buck1_set2	= S5PV210_GPH0(4),
 	.buck2_set3	= S5PV210_GPH0(5),
-	.buck1_max_voltage1 = 1200000,
-	.buck1_max_voltage2 = 1200000,
-	.buck2_max_voltage = 1200000,
+	.buck1_voltage1	= 1200000,
+	.buck1_voltage2	= 1200000,
+	.buck1_voltage3	= 1200000,
+	.buck1_voltage4	= 1200000,
+	.buck2_voltage1	= 1200000,
+	.buck2_voltage2	= 1200000,
 };
 #endif
 

arch/arm/mach-s5pv210/mach-goni.c

@@ -288,7 +288,7 @@ static struct regulator_init_data goni_ldo2_data = {
 
 static struct regulator_init_data goni_ldo3_data = {
 	.constraints	= {
-		.name		= "VUSB/MIPI_1.1V",
+		.name		= "VUSB+MIPI_1.1V",
 		.min_uV		= 1100000,
 		.max_uV		= 1100000,
 		.apply_uV	= 1,
@@ -337,7 +337,7 @@ static struct regulator_init_data goni_ldo7_data = {
 
 static struct regulator_init_data goni_ldo8_data = {
 	.constraints	= {
-		.name		= "VUSB/VADC_3.3V",
+		.name		= "VUSB+VADC_3.3V",
 		.min_uV		= 3300000,
 		.max_uV		= 3300000,
 		.apply_uV	= 1,
@@ -347,7 +347,7 @@ static struct regulator_init_data goni_ldo8_data = {
 
 static struct regulator_init_data goni_ldo9_data = {
 	.constraints	= {
-		.name		= "VCC/VCAM_2.8V",
+		.name		= "VCC+VCAM_2.8V",
 		.min_uV		= 2800000,
 		.max_uV		= 2800000,
 		.apply_uV	= 1,
@@ -521,9 +521,12 @@ static struct max8998_platform_data goni_max8998_pdata = {
 	.buck1_set1	= S5PV210_GPH0(3),
 	.buck1_set2	= S5PV210_GPH0(4),
 	.buck2_set3	= S5PV210_GPH0(5),
-	.buck1_max_voltage1 = 1200000,
-	.buck1_max_voltage2 = 1200000,
-	.buck2_max_voltage = 1200000,
+	.buck1_voltage1	= 1200000,
+	.buck1_voltage2	= 1200000,
+	.buck1_voltage3	= 1200000,
+	.buck1_voltage4	= 1200000,
+	.buck2_voltage1	= 1200000,
+	.buck2_voltage2	= 1200000,
 };
 #endif
 

arch/arm/mach-s5pv310/Kconfig

@@ -122,6 +122,7 @@ config MACH_SMDKV310
 	select S3C_DEV_HSMMC2
 	select S3C_DEV_HSMMC3
 	select S5PV310_DEV_PD
+	select S5PV310_DEV_SYSMMU
 	select S5PV310_SETUP_I2C1
 	select S5PV310_SETUP_SDHCI
 	help

arch/arm/mach-s5pv310/include/mach/map.h

@@ -1,6 +1,6 @@
 /* linux/arch/arm/mach-s5pv310/include/mach/map.h
  *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
  * S5PV310 - Memory map definitions
@@ -23,90 +23,43 @@
 
 #include <plat/map-s5p.h>
 
-#define S5PV310_PA_SYSRAM		(0x02025000)
+#define S5PV310_PA_SYSRAM		0x02025000
 
-#define S5PV310_PA_SROM_BANK(x)		(0x04000000 + ((x) * 0x01000000))
-
-#define S5PC210_PA_ONENAND		(0x0C000000)
-#define S5P_PA_ONENAND			S5PC210_PA_ONENAND
-
-#define S5PC210_PA_ONENAND_DMA		(0x0C600000)
-#define S5P_PA_ONENAND_DMA		S5PC210_PA_ONENAND_DMA
-
-#define S5PV310_PA_CHIPID		(0x10000000)
-#define S5P_PA_CHIPID			S5PV310_PA_CHIPID
-
-#define S5PV310_PA_SYSCON		(0x10010000)
-#define S5P_PA_SYSCON			S5PV310_PA_SYSCON
+#define S5PV310_PA_I2S0			0x03830000
+#define S5PV310_PA_I2S1			0xE3100000
+#define S5PV310_PA_I2S2			0xE2A00000
 
-#define S5PV310_PA_PMU			(0x10020000)
+#define S5PV310_PA_PCM0			0x03840000
+#define S5PV310_PA_PCM1			0x13980000
+#define S5PV310_PA_PCM2			0x13990000
 
-#define S5PV310_PA_CMU			(0x10030000)
-
-#define S5PV310_PA_WATCHDOG		(0x10060000)
-#define S5PV310_PA_RTC			(0x10070000)
-
-#define S5PV310_PA_DMC0			(0x10400000)
-
-#define S5PV310_PA_COMBINER		(0x10448000)
-
-#define S5PV310_PA_COREPERI		(0x10500000)
-#define S5PV310_PA_GIC_CPU		(0x10500100)
-#define S5PV310_PA_TWD			(0x10500600)
-#define S5PV310_PA_GIC_DIST		(0x10501000)
-#define S5PV310_PA_L2CC			(0x10502000)
-
-/* DMA */
-#define S5PV310_PA_MDMA		0x10810000
-#define S5PV310_PA_PDMA0	0x12680000
-#define S5PV310_PA_PDMA1	0x12690000
-
-#define S5PV310_PA_GPIO1		(0x11400000)
-#define S5PV310_PA_GPIO2		(0x11000000)
-#define S5PV310_PA_GPIO3		(0x03860000)
-
-#define S5PV310_PA_MIPI_CSIS0		0x11880000
-#define S5PV310_PA_MIPI_CSIS1		0x11890000
+#define S5PV310_PA_SROM_BANK(x)		(0x04000000 + ((x) * 0x01000000))
 
-#define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
+#define S5PC210_PA_ONENAND		0x0C000000
+#define S5PC210_PA_ONENAND_DMA		0x0C600000
 
-#define S5PV310_PA_SROMC		(0x12570000)
-#define S5P_PA_SROMC			S5PV310_PA_SROMC
+#define S5PV310_PA_CHIPID		0x10000000
 
-/* S/PDIF */
-#define S5PV310_PA_SPDIF	0xE1100000
+#define S5PV310_PA_SYSCON		0x10010000
+#define S5PV310_PA_PMU			0x10020000
+#define S5PV310_PA_CMU			0x10030000
 
-/* I2S */
-#define S5PV310_PA_I2S0		0x03830000
-#define S5PV310_PA_I2S1		0xE3100000
-#define S5PV310_PA_I2S2		0xE2A00000
+#define S5PV310_PA_WATCHDOG		0x10060000
+#define S5PV310_PA_RTC			0x10070000
 
-/* PCM */
-#define S5PV310_PA_PCM0		0x03840000
-#define S5PV310_PA_PCM1		0x13980000
-#define S5PV310_PA_PCM2		0x13990000
+#define S5PV310_PA_DMC0			0x10400000
 
-/* AC97 */
-#define S5PV310_PA_AC97		0x139A0000
+#define S5PV310_PA_COMBINER		0x10448000
 
-#define S5PV310_PA_UART			(0x13800000)
+#define S5PV310_PA_COREPERI		0x10500000
+#define S5PV310_PA_GIC_CPU		0x10500100
+#define S5PV310_PA_TWD			0x10500600
+#define S5PV310_PA_GIC_DIST		0x10501000
+#define S5PV310_PA_L2CC			0x10502000
 
-#define S5P_PA_UART(x)			(S5PV310_PA_UART + ((x) * S3C_UART_OFFSET))
-#define S5P_PA_UART0			S5P_PA_UART(0)
-#define S5P_PA_UART1			S5P_PA_UART(1)
-#define S5P_PA_UART2			S5P_PA_UART(2)
-#define S5P_PA_UART3			S5P_PA_UART(3)
-#define S5P_PA_UART4			S5P_PA_UART(4)
-
-#define S5P_SZ_UART			SZ_256
-
-#define S5PV310_PA_IIC(x)		(0x13860000 + ((x) * 0x10000))
-
-#define S5PV310_PA_TIMER		(0x139D0000)
-#define S5P_PA_TIMER			S5PV310_PA_TIMER
-
-#define S5PV310_PA_SDRAM		(0x40000000)
-#define S5P_PA_SDRAM			S5PV310_PA_SDRAM
+#define S5PV310_PA_MDMA			0x10810000
+#define S5PV310_PA_PDMA0		0x12680000
+#define S5PV310_PA_PDMA1		0x12690000
 
 #define S5PV310_PA_SYSMMU_MDMA		0x10A40000
 #define S5PV310_PA_SYSMMU_SSS		0x10A50000
@@ -124,11 +77,32 @@
 #define S5PV310_PA_SYSMMU_TV		0x12E20000
 #define S5PV310_PA_SYSMMU_MFC_L		0x13620000
 #define S5PV310_PA_SYSMMU_MFC_R		0x13630000
-#define S5PV310_SYSMMU_TOTAL_IPNUM	16
-#define S5P_SYSMMU_TOTAL_IPNUM		S5PV310_SYSMMU_TOTAL_IPNUM
 
-/* compatibiltiy defines. */
-#define S3C_PA_UART			S5PV310_PA_UART
+#define S5PV310_PA_GPIO1		0x11400000
+#define S5PV310_PA_GPIO2		0x11000000
+#define S5PV310_PA_GPIO3		0x03860000
+
+#define S5PV310_PA_MIPI_CSIS0		0x11880000
+#define S5PV310_PA_MIPI_CSIS1		0x11890000
+
+#define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
+
+#define S5PV310_PA_SROMC		0x12570000
+
+#define S5PV310_PA_UART			0x13800000
+
+#define S5PV310_PA_IIC(x)		(0x13860000 + ((x) * 0x10000))
+
+#define S5PV310_PA_AC97			0x139A0000
+
+#define S5PV310_PA_TIMER		0x139D0000
+
+#define S5PV310_PA_SDRAM		0x40000000
+
+#define S5PV310_PA_SPDIF		0xE1100000
+
+/* Compatibiltiy Defines */
+
 #define S3C_PA_HSMMC0			S5PV310_PA_HSMMC(0)
 #define S3C_PA_HSMMC1			S5PV310_PA_HSMMC(1)
 #define S3C_PA_HSMMC2			S5PV310_PA_HSMMC(2)
@@ -143,7 +117,28 @@
 #define S3C_PA_IIC7			S5PV310_PA_IIC(7)
 #define S3C_PA_RTC			S5PV310_PA_RTC
 #define S3C_PA_WDT			S5PV310_PA_WATCHDOG
+
+#define S5P_PA_CHIPID			S5PV310_PA_CHIPID
 #define S5P_PA_MIPI_CSIS0		S5PV310_PA_MIPI_CSIS0
 #define S5P_PA_MIPI_CSIS1		S5PV310_PA_MIPI_CSIS1
+#define S5P_PA_ONENAND			S5PC210_PA_ONENAND
+#define S5P_PA_ONENAND_DMA		S5PC210_PA_ONENAND_DMA
+#define S5P_PA_SDRAM			S5PV310_PA_SDRAM
+#define S5P_PA_SROMC			S5PV310_PA_SROMC
+#define S5P_PA_SYSCON			S5PV310_PA_SYSCON
+#define S5P_PA_TIMER			S5PV310_PA_TIMER
+
+/* UART */
+
+#define S3C_PA_UART			S5PV310_PA_UART
+
+#define S5P_PA_UART(x)			(S3C_PA_UART + ((x) * S3C_UART_OFFSET))
+#define S5P_PA_UART0			S5P_PA_UART(0)
+#define S5P_PA_UART1			S5P_PA_UART(1)
+#define S5P_PA_UART2			S5P_PA_UART(2)
+#define S5P_PA_UART3			S5P_PA_UART(3)
+#define S5P_PA_UART4			S5P_PA_UART(4)
+
+#define S5P_SZ_UART			SZ_256
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s5pv310/include/mach/sysmmu.h

@@ -13,6 +13,9 @@
 #ifndef __ASM_ARM_ARCH_SYSMMU_H
 #define __ASM_ARM_ARCH_SYSMMU_H __FILE__
 
+#define S5PV310_SYSMMU_TOTAL_IPNUM	16
+#define S5P_SYSMMU_TOTAL_IPNUM		S5PV310_SYSMMU_TOTAL_IPNUM
+
 enum s5pv310_sysmmu_ips {
 	SYSMMU_MDMA,
 	SYSMMU_SSS,
@@ -32,7 +35,7 @@ enum s5pv310_sysmmu_ips {
 	SYSMMU_MFC_R,
 };
 
-static char *sysmmu_ips_name[S5P_SYSMMU_TOTAL_IPNUM] = {
+static char *sysmmu_ips_name[S5PV310_SYSMMU_TOTAL_IPNUM] = {
 	"SYSMMU_MDMA"	,
 	"SYSMMU_SSS"	,
 	"SYSMMU_FIMC0"	,