mx31_3ds: revert 3ds debug board relate code

Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.

Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arch/arm/mach-mx3/Kconfig

@@ -67,6 +67,7 @@ config MACH_MX31LITE
 config MACH_MX31_3DS
 	bool "Support MX31PDK (3DS)"
 	select ARCH_MX31
+	select MXC_DEBUG_BOARD
 	select IMX_HAVE_PLATFORM_IMX_UART
 	select IMX_HAVE_PLATFORM_MXC_NAND
 	select IMX_HAVE_PLATFORM_SPI_IMX

arch/arm/mach-mx3/mach-mx31_3ds.c

@@ -18,7 +18,6 @@
 #include <linux/clk.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
-#include <linux/smsc911x.h>
 #include <linux/platform_device.h>
 #include <linux/mfd/mc13783.h>
 #include <linux/spi/spi.h>
@@ -34,6 +33,7 @@
 #include <asm/mach/map.h>
 #include <mach/common.h>
 #include <mach/iomux-mx3.h>
+#include <mach/3ds_debugboard.h>
 
 #include "devices-imx31.h"
 #include "devices.h"
@@ -253,174 +253,12 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
 	.flags = IMXUART_HAVE_RTSCTS,
 };
 
-/*
- * Support for the SMSC9217 on the Debug board.
- */
-
-static struct smsc911x_platform_config smsc911x_config = {
-	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
-	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
-	.flags		= SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
-	.phy_interface	= PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource smsc911x_resources[] = {
-	{
-		.start		= LAN9217_BASE_ADDR,
-		.end		= LAN9217_BASE_ADDR + 0xff,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= EXPIO_INT_ENET,
-		.end		= EXPIO_INT_ENET,
-		.flags		= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device smsc911x_device = {
-	.name		= "smsc911x",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(smsc911x_resources),
-	.resource	= smsc911x_resources,
-	.dev		= {
-		.platform_data = &smsc911x_config,
-	},
-};
-
-/*
- * Routines for the CPLD on the debug board. It contains a CPLD handling
- * LEDs, switches, interrupts for Ethernet.
- */
-
-static void mx31_3ds_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
-{
-	uint32_t imr_val;
-	uint32_t int_valid;
-	uint32_t expio_irq;
-
-	imr_val = __raw_readw(CPLD_INT_MASK_REG);
-	int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val;
-
-	expio_irq = MXC_EXP_IO_BASE;
-	for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
-		if ((int_valid & 1) == 0)
-			continue;
-		generic_handle_irq(expio_irq);
-	}
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * @param irq           an expio virtual irq number
- */
-static void expio_mask_irq(uint32_t irq)
-{
-	uint16_t reg;
-	uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
-	/* mask the interrupt */
-	reg = __raw_readw(CPLD_INT_MASK_REG);
-	reg |= 1 << expio;
-	__raw_writew(reg, CPLD_INT_MASK_REG);
-}
-
-/*
- * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
- * @param irq           an expanded io virtual irq number
- */
-static void expio_ack_irq(uint32_t irq)
-{
-	uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
-	/* clear the interrupt status */
-	__raw_writew(1 << expio, CPLD_INT_RESET_REG);
-	__raw_writew(0, CPLD_INT_RESET_REG);
-	/* mask the interrupt */
-	expio_mask_irq(irq);
-}
-
-/*
- * Enable a expio pin's interrupt by clearing the bit in the imr.
- * @param irq           a expio virtual irq number
- */
-static void expio_unmask_irq(uint32_t irq)
-{
-	uint16_t reg;
-	uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
-	/* unmask the interrupt */
-	reg = __raw_readw(CPLD_INT_MASK_REG);
-	reg &= ~(1 << expio);
-	__raw_writew(reg, CPLD_INT_MASK_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
-	.ack = expio_ack_irq,
-	.mask = expio_mask_irq,
-	.unmask = expio_unmask_irq,
-};
-
-static int __init mx31_3ds_init_expio(void)
-{
-	int i;
-	int ret;
-
-	/* Check if there's a debug board connected */
-	if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) ||
-	    (__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) ||
-	    (__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) {
-		/* No Debug board found */
-		return -ENODEV;
-	}
-
-	pr_info("i.MX31 3DS Debug board detected, rev = 0x%04X\n",
-		__raw_readw(CPLD_CODE_VER_REG));
-
-	/*
-	 * Configure INT line as GPIO input
-	 */
-	ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq");
-	if (ret)
-		pr_warning("could not get LAN irq gpio\n");
-	else
-		gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
-	/* Disable the interrupts and clear the status */
-	__raw_writew(0, CPLD_INT_MASK_REG);
-	__raw_writew(0xFFFF, CPLD_INT_RESET_REG);
-	__raw_writew(0, CPLD_INT_RESET_REG);
-	__raw_writew(0x1F, CPLD_INT_MASK_REG);
-	for (i = MXC_EXP_IO_BASE;
-	     i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
-	     i++) {
-		set_irq_chip(i, &expio_irq_chip);
-		set_irq_handler(i, handle_level_irq);
-		set_irq_flags(i, IRQF_VALID);
-	}
-	set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW);
-	set_irq_chained_handler(EXPIO_PARENT_INT, mx31_3ds_expio_irq_handler);
-
-	return 0;
-}
-
-/*
- * This structure defines the MX31 memory map.
- */
-static struct map_desc mx31_3ds_io_desc[] __initdata = {
-	{
-		.virtual = MX31_CS5_BASE_ADDR_VIRT,
-		.pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
-		.length = MX31_CS5_SIZE,
-		.type = MT_DEVICE,
-	},
-};
-
 /*
  * Set up static virtual mappings.
  */
 static void __init mx31_3ds_map_io(void)
 {
 	mx31_map_io();
-	iotable_init(mx31_3ds_io_desc, ARRAY_SIZE(mx31_3ds_io_desc));
 }
 
 /*!
@@ -443,8 +281,9 @@ static void __init mxc_board_init(void)
 	mx31_3ds_usbotg_init();
 	mxc_register_device(&mxc_otg_udc_device, &usbotg_pdata);
 
-	if (!mx31_3ds_init_expio())
-		platform_device_register(&smsc911x_device);
+	if (!mxc_expio_init(CS5_BASE_ADDR, EXPIO_PARENT_INT))
+		printk(KERN_WARNING "Init of the debugboard failed, all "
+				    "devices on the board are unusable.\n");
 }
 
 static void __init mx31_3ds_timer_init(void)