drivers/ide: PATA driver for Celleb

This is the patch (based on 2.6.19-rc4) for PATA controller of
Toshiba Cell reference set(Celleb). The reference set consists
of Cell, 512MB memory, Super Companion Chip(SCC) and some
peripherals such as HDD, GbE, etc. You can see brief explanation
and picture of Cell reference set at following URLs.

    http://www.toshiba.co.jp/about/press/2005_09/pr2001.htm
    http://cell-industries.com/toshiba_announces.php

We use a drivers/ide driver because its design is more suitable for
SCC IDE controller than libata driver. Since SCC supports only 32bit
read/write, we must override many callbacks of ata_port_operations
by modifying generic helpers. Each time the libata common code is
updated, we must update those modified helpers. It is very hard for us.
But we will try to implement the libata driver as needed.

Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/Kconfig

@@ -797,6 +797,14 @@ config BLK_DEV_IDEDMA_PMAC
 	  to transfer data to and from memory.  Saying Y is safe and improves
 	  performance.
 
+config BLK_DEV_IDE_CELLEB
+	bool "Toshiba's Cell Reference Set IDE support"
+	depends on PPC_CELLEB
+	help
+	  This driver provides support for the built-in IDE controller on
+	  Toshiba Cell Reference Board.
+	  If unsure, say Y.
+
 config BLK_DEV_IDE_SWARM
 	tristate "IDE for Sibyte evaluation boards"
 	depends on SIBYTE_SB1xxx_SOC

drivers/ide/Makefile

@@ -37,6 +37,7 @@ ide-core-$(CONFIG_BLK_DEV_Q40IDE)	+= legacy/q40ide.o
 # built-in only drivers from ppc/
 ide-core-$(CONFIG_BLK_DEV_MPC8xx_IDE)	+= ppc/mpc8xx.o
 ide-core-$(CONFIG_BLK_DEV_IDE_PMAC)	+= ppc/pmac.o
+ide-core-$(CONFIG_BLK_DEV_IDE_CELLEB)	+= ppc/scc_pata.o
 
 # built-in only drivers from h8300/
 ide-core-$(CONFIG_H8300)		+= h8300/ide-h8300.o

drivers/ide/ppc/scc_pata.c

@@ -0,0 +1,812 @@
+/*
+ * Support for IDE interfaces on Celleb platform
+ *
+ * (C) Copyright 2006 TOSHIBA CORPORATION
+ *
+ * This code is based on drivers/ide/pci/siimage.c:
+ * Copyright (C) 2001-2002	Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003		Red Hat <alan@redhat.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/hdreg.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA            0x01b4
+
+#define SCC_PATA_NAME           "scc IDE"
+
+#define TDVHSEL_MASTER          0x00000001
+#define TDVHSEL_SLAVE           0x00000004
+
+#define MODE_JCUSFEN            0x00000080
+
+#define CCKCTRL_ATARESET        0x00040000
+#define CCKCTRL_BUFCNT          0x00020000
+#define CCKCTRL_CRST            0x00010000
+#define CCKCTRL_OCLKEN          0x00000100
+#define CCKCTRL_ATACLKOEN       0x00000002
+#define CCKCTRL_LCLKEN          0x00000001
+
+#define QCHCD_IOS_SS		0x00000001
+
+#define QCHSD_STPDIAG		0x00020000
+
+#define INTMASK_MSK             0xD1000012
+#define INTSTS_SERROR		0x80000000
+#define INTSTS_PRERR		0x40000000
+#define INTSTS_RERR		0x10000000
+#define INTSTS_ICERR		0x01000000
+#define INTSTS_BMSINT		0x00000010
+#define INTSTS_BMHE		0x00000008
+#define INTSTS_IOIRQS           0x00000004
+#define INTSTS_INTRQ            0x00000002
+#define INTSTS_ACTEINT          0x00000001
+
+#define ECMODE_VALUE 0x01
+
+static struct scc_ports {
+	unsigned long ctl, dma;
+	unsigned char hwif_id;  /* for removing hwif from system */
+} scc_ports[MAX_HWIFS];
+
+/* PIO transfer mode  table */
+/* JCHST */
+static unsigned long JCHSTtbl[2][7] = {
+	{0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00},   /* 100MHz */
+	{0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00}    /* 133MHz */
+};
+
+/* JCHHT */
+static unsigned long JCHHTtbl[2][7] = {
+	{0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00},   /* 100MHz */
+	{0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00}    /* 133MHz */
+};
+
+/* JCHCT */
+static unsigned long JCHCTtbl[2][7] = {
+	{0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00},   /* 100MHz */
+	{0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00}    /* 133MHz */
+};
+
+
+/* DMA transfer mode  table */
+/* JCHDCTM/JCHDCTS */
+static unsigned long JCHDCTxtbl[2][7] = {
+	{0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00},   /* 100MHz */
+	{0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00}    /* 133MHz */
+};
+
+/* JCSTWTM/JCSTWTS  */
+static unsigned long JCSTWTxtbl[2][7] = {
+	{0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00},   /* 100MHz */
+	{0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02}    /* 133MHz */
+};
+
+/* JCTSS */
+static unsigned long JCTSStbl[2][7] = {
+	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00},   /* 100MHz */
+	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05}    /* 133MHz */
+};
+
+/* JCENVT */
+static unsigned long JCENVTtbl[2][7] = {
+	{0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00},   /* 100MHz */
+	{0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02}    /* 133MHz */
+};
+
+/* JCACTSELS/JCACTSELM */
+static unsigned long JCACTSELtbl[2][7] = {
+	{0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00},   /* 100MHz */
+	{0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01}    /* 133MHz */
+};
+
+
+static u8 scc_ide_inb(unsigned long port)
+{
+	u32 data = in_be32((void*)port);
+	return (u8)data;
+}
+
+static u16 scc_ide_inw(unsigned long port)
+{
+	u32 data = in_be32((void*)port);
+	return (u16)data;
+}
+
+static u32 scc_ide_inl(unsigned long port)
+{
+	u32 data = in_be32((void*)port);
+	return data;
+}
+
+static void scc_ide_insw(unsigned long port, void *addr, u32 count)
+{
+	u16 *ptr = (u16 *)addr;
+	while (count--) {
+		*ptr++ = le16_to_cpu(in_be32((void*)port));
+	}
+}
+
+static void scc_ide_insl(unsigned long port, void *addr, u32 count)
+{
+	u16 *ptr = (u16 *)addr;
+	while (count--) {
+		*ptr++ = le16_to_cpu(in_be32((void*)port));
+		*ptr++ = le16_to_cpu(in_be32((void*)port));
+	}
+}
+
+static void scc_ide_outb(u8 addr, unsigned long port)
+{
+	out_be32((void*)port, addr);
+}
+
+static void scc_ide_outw(u16 addr, unsigned long port)
+{
+	out_be32((void*)port, addr);
+}
+
+static void scc_ide_outl(u32 addr, unsigned long port)
+{
+	out_be32((void*)port, addr);
+}
+
+static void
+scc_ide_outbsync(ide_drive_t * drive, u8 addr, unsigned long port)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+
+	out_be32((void*)port, addr);
+	__asm__ __volatile__("eieio":::"memory");
+	in_be32((void*)(hwif->dma_base + 0x01c));
+	__asm__ __volatile__("eieio":::"memory");
+}
+
+static void
+scc_ide_outsw(unsigned long port, void *addr, u32 count)
+{
+	u16 *ptr = (u16 *)addr;
+	while (count--) {
+		out_be32((void*)port, cpu_to_le16(*ptr++));
+	}
+}
+
+static void
+scc_ide_outsl(unsigned long port, void *addr, u32 count)
+{
+	u16 *ptr = (u16 *)addr;
+	while (count--) {
+		out_be32((void*)port, cpu_to_le16(*ptr++));
+		out_be32((void*)port, cpu_to_le16(*ptr++));
+	}
+}
+
+/**
+ *	scc_ratemask	-	Compute available modes
+ *	@drive: IDE drive
+ *
+ *	Compute the available speeds for the devices on the interface.
+ *	Enforce UDMA33 as a limit if there is no 80pin cable present.
+ */
+
+static u8 scc_ratemask(ide_drive_t *drive)
+{
+	u8 mode = 4;
+
+	if (!eighty_ninty_three(drive))
+		mode = min(mode, (u8)1);
+	return mode;
+}
+
+/**
+ *	scc_tuneproc	-	tune a drive PIO mode
+ *	@drive: drive to tune
+ *	@mode_wanted: the target operating mode
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller.
+ */
+
+static void scc_tuneproc(ide_drive_t *drive, byte mode_wanted)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct scc_ports *ports = ide_get_hwifdata(hwif);
+	unsigned long ctl_base = ports->ctl;
+	unsigned long cckctrl_port = ctl_base + 0xff0;
+	unsigned long piosht_port = ctl_base + 0x000;
+	unsigned long pioct_port = ctl_base + 0x004;
+	unsigned long reg;
+	unsigned char speed = XFER_PIO_0;
+	int offset;
+
+	mode_wanted = ide_get_best_pio_mode(drive, mode_wanted, 4, NULL);
+	switch (mode_wanted) {
+	case 4:
+		speed = XFER_PIO_4;
+		break;
+	case 3:
+		speed = XFER_PIO_3;
+		break;
+	case 2:
+		speed = XFER_PIO_2;
+		break;
+	case 1:
+		speed = XFER_PIO_1;
+		break;
+	case 0:
+	default:
+		speed = XFER_PIO_0;
+		break;
+	}
+
+	reg = hwif->INL(cckctrl_port);
+	if (reg & CCKCTRL_ATACLKOEN) {
+		offset = 1; /* 133MHz */
+	} else {
+		offset = 0; /* 100MHz */
+	}
+	reg = JCHSTtbl[offset][mode_wanted] << 16 | JCHHTtbl[offset][mode_wanted];
+	hwif->OUTL(reg, piosht_port);
+	reg = JCHCTtbl[offset][mode_wanted];
+	hwif->OUTL(reg, pioct_port);
+
+	ide_config_drive_speed(drive, speed);
+}
+
+/**
+ *	scc_tune_chipset	-	tune a drive DMA mode
+ *	@drive: Drive to set up
+ *	@xferspeed: speed we want to achieve
+ *
+ *	Load the timing settings for this device mode into the
+ *	controller.
+ */
+
+static int scc_tune_chipset(ide_drive_t *drive, byte xferspeed)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	u8 speed = ide_rate_filter(scc_ratemask(drive), xferspeed);
+	struct scc_ports *ports = ide_get_hwifdata(hwif);
+	unsigned long ctl_base = ports->ctl;
+	unsigned long cckctrl_port = ctl_base + 0xff0;
+	unsigned long mdmact_port = ctl_base + 0x008;
+	unsigned long mcrcst_port = ctl_base + 0x00c;
+	unsigned long sdmact_port = ctl_base + 0x010;
+	unsigned long scrcst_port = ctl_base + 0x014;
+	unsigned long udenvt_port = ctl_base + 0x018;
+	unsigned long tdvhsel_port   = ctl_base + 0x020;
+	int is_slave = (&hwif->drives[1] == drive);
+	int offset, idx;
+	unsigned long reg;
+	unsigned long jcactsel;
+
+	reg = hwif->INL(cckctrl_port);
+	if (reg & CCKCTRL_ATACLKOEN) {
+		offset = 1; /* 133MHz */
+	} else {
+		offset = 0; /* 100MHz */
+	}
+
+	switch (speed) {
+	case XFER_UDMA_6:
+		idx = 6;
+		break;
+	case XFER_UDMA_5:
+		idx = 5;
+		break;
+	case XFER_UDMA_4:
+		idx = 4;
+		break;
+	case XFER_UDMA_3:
+		idx = 3;
+		break;
+	case XFER_UDMA_2:
+		idx = 2;
+		break;
+	case XFER_UDMA_1:
+		idx = 1;
+		break;
+	case XFER_UDMA_0:
+		idx = 0;
+		break;
+	default:
+		return 1;
+	}
+
+	jcactsel = JCACTSELtbl[offset][idx];
+	if (is_slave) {
+		hwif->OUTL(JCHDCTxtbl[offset][idx], sdmact_port);
+		hwif->OUTL(JCSTWTxtbl[offset][idx], scrcst_port);
+		jcactsel = jcactsel << 2 ;
+		hwif->OUTL( (hwif->INL( tdvhsel_port ) & ~TDVHSEL_SLAVE) | jcactsel, tdvhsel_port );
+	} else {
+		hwif->OUTL(JCHDCTxtbl[offset][idx], mdmact_port);
+		hwif->OUTL(JCSTWTxtbl[offset][idx], mcrcst_port);
+		hwif->OUTL( (hwif->INL( tdvhsel_port ) & ~TDVHSEL_MASTER) | jcactsel, tdvhsel_port );
+	}
+	reg = JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx];
+	hwif->OUTL(reg, udenvt_port);
+
+	return ide_config_drive_speed(drive, speed);
+}
+
+/**
+ *	scc_config_chipset_for_dma	-	configure for DMA
+ *	@drive: drive to configure
+ *
+ *	Called by scc_config_drive_for_dma().
+ */
+
+static int scc_config_chipset_for_dma(ide_drive_t *drive)
+{
+	u8 speed = ide_dma_speed(drive, scc_ratemask(drive));
+
+	if (!speed)
+		return 0;
+
+	if (ide_set_xfer_rate(drive, speed))
+		return 0;
+
+	if (!drive->init_speed)
+		drive->init_speed = speed;
+
+	return ide_dma_enable(drive);
+}
+
+/**
+ *	scc_configure_drive_for_dma	-	set up for DMA transfers
+ *	@drive: drive we are going to set up
+ *
+ *	Set up the drive for DMA, tune the controller and drive as
+ *	required.
+ *      If the drive isn't suitable for DMA or we hit other problems
+ *      then we will drop down to PIO and set up PIO appropriately.
+ *      (return 1)
+ */
+
+static int scc_config_drive_for_dma(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct hd_driveid *id = drive->id;
+
+	if ((id->capability & 1) != 0 && drive->autodma) {
+		if (ide_use_dma(drive)) {
+			if (scc_config_chipset_for_dma(drive))
+				return hwif->ide_dma_on(drive);
+		}
+		goto fast_ata_pio;
+	} else if ((id->capability & 8) || (id->field_valid & 2)) {
+	fast_ata_pio:
+		hwif->tuneproc(drive, 4);
+		hwif->ide_dma_off_quietly(drive);
+	}
+	return 1; /* DMA is not supported */
+}
+
+/**
+ *	scc_ide_dma_end	-	Stop DMA
+ *	@drive: IDE drive
+ *
+ *	Check and clear INT Status register.
+ *      Then call __ide_dma_end().
+ */
+
+static int scc_ide_dma_end(ide_drive_t * drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	unsigned long intsts_port = hwif->dma_base + 0x014;
+	u32 reg;
+
+	while (1) {
+		reg = hwif->INL(intsts_port);
+
+		if (reg & INTSTS_SERROR) {
+			printk(KERN_WARNING "%s: SERROR\n", SCC_PATA_NAME);
+			hwif->OUTL(INTSTS_SERROR|INTSTS_BMSINT, intsts_port);
+
+			hwif->OUTB(hwif->INB(hwif->dma_command) & ~QCHCD_IOS_SS,
+				   hwif->dma_command);
+			continue;
+		}
+
+		if (reg & INTSTS_PRERR) {
+			u32 maea0, maec0;
+			unsigned long ctl_base = hwif->config_data;
+
+			maea0 = hwif->INL(ctl_base + 0xF50);
+			maec0 = hwif->INL(ctl_base + 0xF54);
+
+			printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", SCC_PATA_NAME, maea0, maec0);
+
+			hwif->OUTL(INTSTS_PRERR|INTSTS_BMSINT, intsts_port);
+
+			hwif->OUTB(hwif->INB(hwif->dma_command) & ~QCHCD_IOS_SS,
+				   hwif->dma_command);
+			continue;
+		}
+
+		if (reg & INTSTS_RERR) {
+			printk(KERN_WARNING "%s: Response Error\n", SCC_PATA_NAME);
+			hwif->OUTL(INTSTS_RERR|INTSTS_BMSINT, intsts_port);
+
+			hwif->OUTB(hwif->INB(hwif->dma_command) & ~QCHCD_IOS_SS,
+				   hwif->dma_command);
+			continue;
+		}
+
+		if (reg & INTSTS_ICERR) {
+			hwif->OUTB(hwif->INB(hwif->dma_command) & ~QCHCD_IOS_SS,
+				   hwif->dma_command);
+
+			printk(KERN_WARNING "%s: Illegal Configuration\n", SCC_PATA_NAME);
+			hwif->OUTL(INTSTS_ICERR|INTSTS_BMSINT, intsts_port);
+			continue;
+		}
+
+		if (reg & INTSTS_BMSINT) {
+			printk(KERN_WARNING "%s: Internal Bus Error\n", SCC_PATA_NAME);
+			hwif->OUTL(INTSTS_BMSINT, intsts_port);
+
+			ide_do_reset(drive);
+			continue;
+		}
+
+		if (reg & INTSTS_BMHE) {
+			hwif->OUTL(INTSTS_BMHE, intsts_port);
+			continue;
+		}
+
+		if (reg & INTSTS_ACTEINT) {
+			hwif->OUTL(INTSTS_ACTEINT, intsts_port);
+			continue;
+		}
+
+		if (reg & INTSTS_IOIRQS) {
+			hwif->OUTL(INTSTS_IOIRQS, intsts_port);
+			continue;
+		}
+		break;
+	}
+
+	return __ide_dma_end(drive);
+}
+
+/**
+ *	setup_mmio_scc	-	map CTRL/BMID region
+ *	@dev: PCI device we are configuring
+ *	@name: device name
+ *
+ */
+
+static int setup_mmio_scc (struct pci_dev *dev, const char *name)
+{
+	unsigned long ctl_base = pci_resource_start(dev, 0);
+	unsigned long dma_base = pci_resource_start(dev, 1);
+	unsigned long ctl_size = pci_resource_len(dev, 0);
+	unsigned long dma_size = pci_resource_len(dev, 1);
+	void *ctl_addr;
+	void *dma_addr;
+	int i;
+
+	for (i = 0; i < MAX_HWIFS; i++) {
+		if (scc_ports[i].ctl == 0)
+			break;
+	}
+	if (i >= MAX_HWIFS)
+		return -ENOMEM;
+
+	if (!request_mem_region(ctl_base, ctl_size, name)) {
+		printk(KERN_WARNING "%s: IDE controller MMIO ports not available.\n", SCC_PATA_NAME);
+		goto fail_0;
+	}
+
+	if (!request_mem_region(dma_base, dma_size, name)) {
+		printk(KERN_WARNING "%s: IDE controller MMIO ports not available.\n", SCC_PATA_NAME);
+		goto fail_1;
+	}
+
+	if ((ctl_addr = ioremap(ctl_base, ctl_size)) == NULL)
+		goto fail_2;
+
+	if ((dma_addr = ioremap(dma_base, dma_size)) == NULL)
+		goto fail_3;
+
+	pci_set_master(dev);
+	scc_ports[i].ctl = (unsigned long)ctl_addr;
+	scc_ports[i].dma = (unsigned long)dma_addr;
+	pci_set_drvdata(dev, (void *) &scc_ports[i]);
+
+	return 1;
+
+ fail_3:
+	iounmap(ctl_addr);
+ fail_2:
+	release_mem_region(dma_base, dma_size);
+ fail_1:
+	release_mem_region(ctl_base, ctl_size);
+ fail_0:
+	return -ENOMEM;
+}
+
+/**
+ *	init_setup_scc	-	set up an SCC PATA Controller
+ *	@dev: PCI device
+ *	@d: IDE PCI device
+ *
+ *	Perform the initial set up for this device.
+ */
+
+static int __devinit init_setup_scc(struct pci_dev *dev, ide_pci_device_t *d)
+{
+	unsigned long ctl_base;
+	unsigned long dma_base;
+	unsigned long cckctrl_port;
+	unsigned long intmask_port;
+	unsigned long mode_port;
+	unsigned long ecmode_port;
+	unsigned long dma_status_port;
+	u32 reg = 0;
+	struct scc_ports *ports;
+	int rc;
+
+	rc = setup_mmio_scc(dev, d->name);
+	if (rc < 0) {
+		return rc;
+	}
+
+	ports = pci_get_drvdata(dev);
+	ctl_base = ports->ctl;
+	dma_base = ports->dma;
+	cckctrl_port = ctl_base + 0xff0;
+	intmask_port = dma_base + 0x010;
+	mode_port = ctl_base + 0x024;
+	ecmode_port = ctl_base + 0xf00;
+	dma_status_port = dma_base + 0x004;
+
+	/* controller initialization */
+	reg = 0;
+	out_be32((void*)cckctrl_port, reg);
+	reg |= CCKCTRL_ATACLKOEN;
+	out_be32((void*)cckctrl_port, reg);
+	reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
+	out_be32((void*)cckctrl_port, reg);
+	reg |= CCKCTRL_CRST;
+	out_be32((void*)cckctrl_port, reg);
+
+	for (;;) {
+		reg = in_be32((void*)cckctrl_port);
+		if (reg & CCKCTRL_CRST)
+			break;
+		udelay(5000);
+	}
+
+	reg |= CCKCTRL_ATARESET;
+	out_be32((void*)cckctrl_port, reg);
+
+	out_be32((void*)ecmode_port, ECMODE_VALUE);
+	out_be32((void*)mode_port, MODE_JCUSFEN);
+	out_be32((void*)intmask_port, INTMASK_MSK);
+
+	return ide_setup_pci_device(dev, d);
+}
+
+/**
+ *	init_mmio_iops_scc	-	set up the iops for MMIO
+ *	@hwif: interface to set up
+ *
+ */
+
+static void __devinit init_mmio_iops_scc(ide_hwif_t *hwif)
+{
+	struct pci_dev *dev = hwif->pci_dev;
+	struct scc_ports *ports = pci_get_drvdata(dev);
+	unsigned long dma_base = ports->dma;
+
+	ide_set_hwifdata(hwif, ports);
+
+	hwif->INB = scc_ide_inb;
+	hwif->INW = scc_ide_inw;
+	hwif->INL = scc_ide_inl;
+	hwif->INSW = scc_ide_insw;
+	hwif->INSL = scc_ide_insl;
+	hwif->OUTB = scc_ide_outb;
+	hwif->OUTBSYNC = scc_ide_outbsync;
+	hwif->OUTW = scc_ide_outw;
+	hwif->OUTL = scc_ide_outl;
+	hwif->OUTSW = scc_ide_outsw;
+	hwif->OUTSL = scc_ide_outsl;
+
+	hwif->io_ports[IDE_DATA_OFFSET] = dma_base + 0x20;
+	hwif->io_ports[IDE_ERROR_OFFSET] = dma_base + 0x24;
+	hwif->io_ports[IDE_NSECTOR_OFFSET] = dma_base + 0x28;
+	hwif->io_ports[IDE_SECTOR_OFFSET] = dma_base + 0x2c;
+	hwif->io_ports[IDE_LCYL_OFFSET] = dma_base + 0x30;
+	hwif->io_ports[IDE_HCYL_OFFSET] = dma_base + 0x34;
+	hwif->io_ports[IDE_SELECT_OFFSET] = dma_base + 0x38;
+	hwif->io_ports[IDE_STATUS_OFFSET] = dma_base + 0x3c;
+	hwif->io_ports[IDE_CONTROL_OFFSET] = dma_base + 0x40;
+
+	hwif->irq = hwif->pci_dev->irq;
+	hwif->dma_base = dma_base;
+	hwif->config_data = ports->ctl;
+	hwif->mmio = 2;
+}
+
+/**
+ *	init_iops_scc	-	set up iops
+ *	@hwif: interface to set up
+ *
+ *	Do the basic setup for the SCC hardware interface
+ *	and then do the MMIO setup.
+ */
+
+static void __devinit init_iops_scc(ide_hwif_t *hwif)
+{
+	struct pci_dev *dev =  hwif->pci_dev;
+	hwif->hwif_data = NULL;
+	if (pci_get_drvdata(dev) == NULL)
+		return;
+	init_mmio_iops_scc(hwif);
+}
+
+/**
+ *	init_hwif_scc	-	set up hwif
+ *	@hwif: interface to set up
+ *
+ *	We do the basic set up of the interface structure. The SCC
+ *	requires several custom handlers so we override the default
+ *	ide DMA handlers appropriately.
+ */
+
+static void __devinit init_hwif_scc(ide_hwif_t *hwif)
+{
+	struct scc_ports *ports = ide_get_hwifdata(hwif);
+
+	ports->hwif_id = hwif->index;
+
+	hwif->dma_command = hwif->dma_base;
+	hwif->dma_status = hwif->dma_base + 0x04;
+	hwif->dma_prdtable = hwif->dma_base + 0x08;
+
+	hwif->OUTL(hwif->dmatable_dma, (hwif->dma_base + 0x018)); /* PTERADD */
+
+	hwif->ide_dma_end = scc_ide_dma_end;
+	hwif->speedproc = scc_tune_chipset;
+	hwif->tuneproc = scc_tuneproc;
+	hwif->ide_dma_check = scc_config_drive_for_dma;
+
+	hwif->drives[0].autotune = IDE_TUNE_AUTO;
+	hwif->drives[1].autotune = IDE_TUNE_AUTO;
+
+	if (hwif->INL(hwif->config_data + 0xff0) & CCKCTRL_ATACLKOEN) {
+		hwif->ultra_mask = 0x7f; /* 133MHz */
+	} else {
+		hwif->ultra_mask = 0x3f; /* 100MHz */
+	}
+	hwif->mwdma_mask = 0x00;
+	hwif->swdma_mask = 0x00;
+	hwif->atapi_dma = 1;
+
+	/* we support 80c cable only. */
+	hwif->udma_four = 1;
+
+	hwif->autodma = 0;
+	if (!noautodma)
+		hwif->autodma = 1;
+	hwif->drives[0].autodma = hwif->autodma;
+	hwif->drives[1].autodma = hwif->autodma;
+}
+
+#define DECLARE_SCC_DEV(name_str)			\
+  {							\
+      .name		= name_str,			\
+      .init_setup	= init_setup_scc,		\
+      .init_iops	= init_iops_scc,		\
+      .init_hwif	= init_hwif_scc,		\
+      .channels	= 1,					\
+      .autodma	= AUTODMA,				\
+      .bootable	= ON_BOARD,				\
+  }
+
+static ide_pci_device_t scc_chipsets[] __devinitdata = {
+	/* 0 */ DECLARE_SCC_DEV("sccIDE"),
+};
+
+/**
+ *	scc_init_one	-	pci layer discovery entry
+ *	@dev: PCI device
+ *	@id: ident table entry
+ *
+ *	Called by the PCI code when it finds an SCC PATA controller.
+ *	We then use the IDE PCI generic helper to do most of the work.
+ */
+
+static int __devinit scc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	ide_pci_device_t *d = &scc_chipsets[id->driver_data];
+	return d->init_setup(dev, d);
+}
+
+/**
+ *	scc_remove	-	pci layer remove entry
+ *	@dev: PCI device
+ *
+ *	Called by the PCI code when it removes an SCC PATA controller.
+ */
+
+static void __devexit scc_remove(struct pci_dev *dev)
+{
+	struct scc_ports *ports = pci_get_drvdata(dev);
+	ide_hwif_t *hwif = &ide_hwifs[ports->hwif_id];
+	unsigned long ctl_base = pci_resource_start(dev, 0);
+	unsigned long dma_base = pci_resource_start(dev, 1);
+	unsigned long ctl_size = pci_resource_len(dev, 0);
+	unsigned long dma_size = pci_resource_len(dev, 1);
+
+	if (hwif->dmatable_cpu) {
+		pci_free_consistent(hwif->pci_dev,
+				    PRD_ENTRIES * PRD_BYTES,
+				    hwif->dmatable_cpu,
+				    hwif->dmatable_dma);
+		hwif->dmatable_cpu = NULL;
+	}
+
+	ide_unregister(hwif->index);
+
+	hwif->chipset = ide_unknown;
+	iounmap((void*)ports->dma);
+	iounmap((void*)ports->ctl);
+	release_mem_region(dma_base, dma_size);
+	release_mem_region(ctl_base, ctl_size);
+	memset(ports, 0, sizeof(*ports));
+}
+
+static struct pci_device_id scc_pci_tbl[] = {
+	{ PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
+
+static struct pci_driver driver = {
+	.name = "SCC IDE",
+	.id_table = scc_pci_tbl,
+	.probe = scc_init_one,
+	.remove = scc_remove,
+};
+
+static int scc_ide_init(void)
+{
+	return ide_pci_register_driver(&driver);
+}
+
+module_init(scc_ide_init);
+/* -- No exit code?
+static void scc_ide_exit(void)
+{
+	ide_pci_unregister_driver(&driver);
+}
+module_exit(scc_ide_exit);
+ */
+
+
+MODULE_DESCRIPTION("PCI driver module for Toshiba SCC IDE");
+MODULE_LICENSE("GPL");