Staging: ipack: add support for IP-OCTAL mezzanine board

IP-OCTAL is a 8-channels serial port device. There are several models one per
each standard: RS-232, RS-422, RS-485.

This driver can manage all of them.

Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/ipack/Kconfig

@@ -9,6 +9,8 @@ menuconfig IPACK_BUS
 
 if IPACK_BUS
 
+source "drivers/staging/ipack/devices/Kconfig"
+
 source "drivers/staging/ipack/bridges/Kconfig"
 
 endif # IPACK

drivers/staging/ipack/Makefile

@@ -2,4 +2,5 @@
 # Makefile for the IPACK bridge device drivers.
 #
 obj-$(CONFIG_IPACK_BUS)		+= ipack.o
+obj-y				+= devices/
 obj-y				+= bridges/

drivers/staging/ipack/TODO

@@ -22,6 +22,15 @@ TPCI-200
 * It has a linked list with the tpci200 devices it is managing. Get rid of it
   and use driver_for_each_device() instead.
 
+IP-OCTAL
+--------
+
+* It has a linked list which saves the devices it is currently
+  managing. It should use the driver_for_each_device() function. It is not there
+  due to the impossibility of using container_of macro to recover the
+  corresponding "struct ipoctal" because the attribute "struct ipack_device" is
+  a pointer. This code should be refactored.
+
 Ipack
 -----
 

drivers/staging/ipack/devices/Kconfig

@@ -0,0 +1,7 @@
+config SERIAL_IPOCTAL
+	tristate "IndustryPack IP-OCTAL uart support"
+	depends on IPACK_BUS
+	help
+	  This driver supports the IPOCTAL serial port device for the IndustryPack bus.
+	default n
+

drivers/staging/ipack/devices/Makefile

@@ -0,0 +1 @@
+obj-$(CONFIG_SERIAL_IPOCTAL) += ipoctal.o

drivers/staging/ipack/devices/ipoctal.c

@@ -0,0 +1,893 @@
+/**
+ * ipoctal.c
+ *
+ * driver for the GE IP-OCTAL boards
+ * Copyright (c) 2009 Nicolas Serafini, EIC2 SA
+ * Copyright (c) 2010,2011 Samuel Iglesias Gonsalvez <siglesia@cern.ch>, CERN
+ * Copyright (c) 2012 Samuel Iglesias Gonsalvez <siglesias@igalia.com>, Igalia
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/interrupt.h>
+#include <linux/fs.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/tty.h>
+#include <linux/serial.h>
+#include <linux/tty_flip.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/atomic.h>
+#include "../ipack.h"
+#include "ipoctal.h"
+#include "scc2698.h"
+
+#define IP_OCTAL_MANUFACTURER_ID    0xF0
+#define IP_OCTAL_232_ID             0x22
+#define IP_OCTAL_422_ID             0x2A
+#define IP_OCTAL_485_ID             0x48
+
+#define IP_OCTAL_ID_SPACE_VECTOR    0x41
+#define IP_OCTAL_NB_BLOCKS          4
+
+static struct ipack_driver driver;
+static const struct tty_operations ipoctal_fops;
+
+struct ipoctal {
+	struct list_head		list;
+	struct ipack_device		*dev;
+	unsigned int			board_id;
+	struct scc2698_channel		*chan_regs;
+	struct scc2698_block		*block_regs;
+	struct ipoctal_stats		chan_stats[NR_CHANNELS];
+	char				*buffer[NR_CHANNELS];
+	unsigned int			nb_bytes[NR_CHANNELS];
+	unsigned int			count_wr[NR_CHANNELS];
+	struct ipoctal_config		chan_config[NR_CHANNELS];
+	wait_queue_head_t		queue[NR_CHANNELS];
+	unsigned short			error_flag[NR_CHANNELS];
+	spinlock_t			lock[NR_CHANNELS];
+	unsigned int			pointer_read[NR_CHANNELS];
+	unsigned int			pointer_write[NR_CHANNELS];
+	atomic_t			open[NR_CHANNELS];
+	unsigned char			write;
+	struct tty_port			tty_port[NR_CHANNELS];
+	struct tty_driver		*tty_drv;
+};
+
+/* Linked list to save the registered devices */
+static LIST_HEAD(ipoctal_list);
+
+static inline void ipoctal_write_io_reg(struct ipoctal *ipoctal,
+					unsigned char *dest,
+					unsigned char value)
+{
+	unsigned long offset;
+
+	offset = ((void *) dest) - ipoctal->dev->io_space.address;
+	ipoctal->dev->ops->write8(ipoctal->dev, IPACK_IO_SPACE, offset, value);
+}
+
+static inline void ipoctal_write_cr_cmd(struct ipoctal *ipoctal,
+					unsigned char *dest,
+					unsigned char value)
+{
+	ipoctal_write_io_reg(ipoctal, dest, value);
+}
+
+static inline unsigned char ipoctal_read_io_reg(struct ipoctal *ipoctal,
+						unsigned char *src)
+{
+	unsigned long offset;
+	unsigned char value;
+
+	offset = ((void *) src) - ipoctal->dev->io_space.address;
+	ipoctal->dev->ops->read8(ipoctal->dev, IPACK_IO_SPACE, offset, &value);
+	return value;
+}
+
+static struct ipoctal *ipoctal_find_board(struct tty_struct *tty)
+{
+	struct ipoctal *p;
+
+	list_for_each_entry(p, &ipoctal_list, list) {
+		if (tty->driver->major == p->tty_drv->major)
+			return p;
+	}
+
+	return NULL;
+}
+
+static int ipoctal_port_activate(struct tty_port *port, struct tty_struct *tty)
+{
+	struct ipoctal *ipoctal;
+	int channel = tty->index;
+
+	ipoctal = ipoctal_find_board(tty);
+
+	if (ipoctal == NULL) {
+		pr_err("Device not found. Major %d\n", tty->driver->major);
+		return -ENODEV;
+	}
+
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_ENABLE_RX);
+	tty->driver_data = ipoctal;
+
+	return 0;
+}
+
+static int ipoctal_open(struct tty_struct *tty, struct file *file)
+{
+	int channel = tty->index;
+	int res;
+	struct ipoctal *ipoctal;
+
+	ipoctal = ipoctal_find_board(tty);
+
+	if (ipoctal == NULL) {
+		pr_err("Device not found. Major %d\n", tty->driver->major);
+		return -ENODEV;
+	}
+
+	if (atomic_read(&ipoctal->open[channel]))
+		return -EBUSY;
+
+	res = tty_port_open(&ipoctal->tty_port[channel], tty, file);
+	if (res)
+		return res;
+
+	atomic_inc(&ipoctal->open[channel]);
+	return 0;
+}
+
+static void ipoctal_reset_stats(struct ipoctal_stats *stats)
+{
+	stats->tx = 0;
+	stats->rx = 0;
+	stats->rcv_break = 0;
+	stats->framing_err = 0;
+	stats->overrun_err = 0;
+	stats->parity_err = 0;
+}
+
+static void ipoctal_free_channel(struct tty_struct *tty)
+{
+	int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	if (ipoctal == NULL)
+		return;
+
+	ipoctal_reset_stats(&ipoctal->chan_stats[channel]);
+	ipoctal->pointer_read[channel] = 0;
+	ipoctal->pointer_write[channel] = 0;
+	ipoctal->nb_bytes[channel] = 0;
+}
+
+static void ipoctal_close(struct tty_struct *tty, struct file *filp)
+{
+	int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	tty_port_close(&ipoctal->tty_port[channel], tty, filp);
+
+	if (atomic_dec_and_test(&ipoctal->open[channel]))
+		ipoctal_free_channel(tty);
+}
+
+static int ipoctal_get_icount(struct tty_struct *tty,
+			      struct serial_icounter_struct *icount)
+{
+	struct ipoctal *ipoctal = tty->driver_data;
+	int channel = tty->index;
+
+	icount->cts = 0;
+	icount->dsr = 0;
+	icount->rng = 0;
+	icount->dcd = 0;
+	icount->rx = ipoctal->chan_stats[channel].rx;
+	icount->tx = ipoctal->chan_stats[channel].tx;
+	icount->frame = ipoctal->chan_stats[channel].framing_err;
+	icount->parity = ipoctal->chan_stats[channel].parity_err;
+	icount->brk = ipoctal->chan_stats[channel].rcv_break;
+	return 0;
+}
+
+static int ipoctal_irq_handler(void *arg)
+{
+	unsigned int channel;
+	unsigned int block;
+	unsigned char isr;
+	unsigned char sr;
+	unsigned char isr_tx_rdy, isr_rx_rdy;
+	unsigned char value;
+	unsigned char flag;
+	struct tty_struct *tty;
+	struct ipoctal *ipoctal = (struct ipoctal *) arg;
+
+	/* Check all channels */
+	for (channel = 0; channel < NR_CHANNELS; channel++) {
+		/* If there is no client, skip the check */
+		if (!atomic_read(&ipoctal->open[channel]))
+			continue;
+
+		tty = tty_port_tty_get(&ipoctal->tty_port[channel]);
+		if (!tty)
+			continue;
+
+		/*
+		 * The HW is organized in pair of channels.
+		 * See which register we need to read from
+		 */
+		block = channel / 2;
+		isr = ipoctal_read_io_reg(ipoctal,
+					  &ipoctal->block_regs[block].u.r.isr);
+		sr = ipoctal_read_io_reg(ipoctal,
+					 &ipoctal->chan_regs[channel].u.r.sr);
+
+		if ((channel % 2) == 1) {
+			isr_tx_rdy = isr & ISR_TxRDY_B;
+			isr_rx_rdy = isr & ISR_RxRDY_FFULL_B;
+		} else {
+			isr_tx_rdy = isr & ISR_TxRDY_A;
+			isr_rx_rdy = isr & ISR_RxRDY_FFULL_A;
+		}
+
+		/* In case of RS-485, change from TX to RX when finishing TX.
+		 * Half-duplex.
+		 */
+		if ((ipoctal->board_id == IP_OCTAL_485_ID) &&
+		    (sr & SR_TX_EMPTY) &&
+		    (ipoctal->nb_bytes[channel] == 0)) {
+			ipoctal_write_io_reg(ipoctal,
+					     &ipoctal->chan_regs[channel].u.w.cr,
+					     CR_DISABLE_TX);
+			ipoctal_write_cr_cmd(ipoctal,
+					     &ipoctal->chan_regs[channel].u.w.cr,
+					     CR_CMD_NEGATE_RTSN);
+			ipoctal_write_io_reg(ipoctal,
+					     &ipoctal->chan_regs[channel].u.w.cr,
+					     CR_ENABLE_RX);
+			ipoctal->write = 1;
+			wake_up_interruptible(&ipoctal->queue[channel]);
+		}
+
+		/* RX data */
+		if (isr_rx_rdy && (sr & SR_RX_READY)) {
+			value = ipoctal_read_io_reg(ipoctal,
+						    &ipoctal->chan_regs[channel].u.r.rhr);
+			flag = TTY_NORMAL;
+
+			/* Error: count statistics */
+			if (sr & SR_ERROR) {
+				ipoctal_write_cr_cmd(ipoctal,
+						     &ipoctal->chan_regs[channel].u.w.cr,
+						     CR_CMD_RESET_ERR_STATUS);
+
+				if (sr & SR_OVERRUN_ERROR) {
+					ipoctal->error_flag[channel] |= UART_OVERRUN;
+					ipoctal->chan_stats[channel].overrun_err++;
+					/* Overrun doesn't affect the current character*/
+					tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+				}
+				if (sr & SR_PARITY_ERROR) {
+					ipoctal->error_flag[channel] |= UART_PARITY;
+					ipoctal->chan_stats[channel].parity_err++;
+					flag = TTY_PARITY;
+				}
+				if (sr & SR_FRAMING_ERROR) {
+					ipoctal->error_flag[channel] |= UART_FRAMING;
+					ipoctal->chan_stats[channel].framing_err++;
+					flag = TTY_FRAME;
+				}
+				if (sr & SR_RECEIVED_BREAK) {
+					ipoctal->error_flag[channel] |= UART_BREAK;
+					ipoctal->chan_stats[channel].rcv_break++;
+					flag = TTY_BREAK;
+				}
+			}
+
+			tty_insert_flip_char(tty, value, flag);
+		}
+
+		/* TX of each character */
+		if (isr_tx_rdy && (sr & SR_TX_READY)) {
+			unsigned int *pointer_write =
+				&ipoctal->pointer_write[channel];
+
+			if (ipoctal->nb_bytes[channel] <= 0) {
+				ipoctal->nb_bytes[channel] = 0;
+				continue;
+			}
+			spin_lock(&ipoctal->lock[channel]);
+			value = ipoctal->buffer[channel][*pointer_write];
+			ipoctal_write_io_reg(ipoctal,
+					     &ipoctal->chan_regs[channel].u.w.thr,
+					     value);
+			ipoctal->chan_stats[channel].tx++;
+			ipoctal->count_wr[channel]++;
+			(*pointer_write)++;
+			*pointer_write = *pointer_write % PAGE_SIZE;
+			ipoctal->nb_bytes[channel]--;
+			spin_unlock(&ipoctal->lock[channel]);
+
+			if ((ipoctal->nb_bytes[channel] == 0) &&
+			    (waitqueue_active(&ipoctal->queue[channel]))) {
+
+				if (ipoctal->board_id != IP_OCTAL_485_ID) {
+					ipoctal->write = 1;
+					wake_up_interruptible(&ipoctal->queue[channel]);
+				}
+			}
+		}
+
+		tty_flip_buffer_push(tty);
+		tty_kref_put(tty);
+	}
+	return IRQ_HANDLED;
+}
+
+static int ipoctal_check_model(struct ipack_device *dev, unsigned char *id)
+{
+	unsigned char manufacturerID;
+	unsigned char board_id;
+
+	dev->ops->read8(dev, IPACK_ID_SPACE,
+			IPACK_IDPROM_OFFSET_MANUFACTURER_ID, &manufacturerID);
+	if (manufacturerID != IP_OCTAL_MANUFACTURER_ID)
+		return -ENODEV;
+
+	dev->ops->read8(dev, IPACK_ID_SPACE,
+			IPACK_IDPROM_OFFSET_MODEL, (unsigned char *)&board_id);
+
+	switch (board_id) {
+	case IP_OCTAL_232_ID:
+	case IP_OCTAL_422_ID:
+	case IP_OCTAL_485_ID:
+		*id = board_id;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static const struct tty_port_operations ipoctal_tty_port_ops = {
+	.dtr_rts = NULL,
+	.activate = ipoctal_port_activate,
+};
+
+static int ipoctal_inst_slot(struct ipoctal *ipoctal, unsigned int bus_nr,
+			     unsigned int slot, unsigned int vector)
+{
+	int res = 0;
+	int i;
+	struct tty_driver *tty;
+	char name[20];
+	unsigned char board_id;
+
+	res = ipoctal->dev->ops->map_space(ipoctal->dev, 0, IPACK_ID_SPACE);
+	if (res) {
+		pr_err("Unable to map slot [%d:%d] ID space!\n", bus_nr, slot);
+		return res;
+	}
+
+	res = ipoctal_check_model(ipoctal->dev, &board_id);
+	if (res) {
+		ipoctal->dev->ops->unmap_space(ipoctal->dev, IPACK_ID_SPACE);
+		goto out_unregister_id_space;
+	}
+	ipoctal->board_id = board_id;
+
+	res = ipoctal->dev->ops->map_space(ipoctal->dev, 0, IPACK_IO_SPACE);
+	if (res) {
+		pr_err("Unable to map slot [%d:%d] IO space!\n", bus_nr, slot);
+		goto out_unregister_id_space;
+	}
+
+	res = ipoctal->dev->ops->map_space(ipoctal->dev,
+					   0x8000, IPACK_MEM_SPACE);
+	if (res) {
+		pr_err("Unable to map slot [%d:%d] MEM space!\n", bus_nr, slot);
+		goto out_unregister_io_space;
+	}
+
+	/* Save the virtual address to access the registers easily */
+	ipoctal->chan_regs =
+		(struct scc2698_channel *) ipoctal->dev->io_space.address;
+	ipoctal->block_regs =
+		(struct scc2698_block *) ipoctal->dev->io_space.address;
+
+	/* Disable RX and TX before touching anything */
+	for (i = 0; i < NR_CHANNELS ; i++) {
+		ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[i].u.w.cr,
+				     CR_DISABLE_RX | CR_DISABLE_TX);
+	}
+
+	for (i = 0; i < IP_OCTAL_NB_BLOCKS; i++) {
+		ipoctal_write_io_reg(ipoctal,
+				     &ipoctal->block_regs[i].u.w.acr,
+				     ACR_BRG_SET2);
+		ipoctal_write_io_reg(ipoctal,
+				     &ipoctal->block_regs[i].u.w.opcr,
+				     OPCR_MPP_OUTPUT | OPCR_MPOa_RTSN |
+				     OPCR_MPOb_RTSN);
+		ipoctal_write_io_reg(ipoctal,
+				     &ipoctal->block_regs[i].u.w.imr,
+				     IMR_TxRDY_A | IMR_RxRDY_FFULL_A |
+				     IMR_DELTA_BREAK_A | IMR_TxRDY_B |
+				     IMR_RxRDY_FFULL_B | IMR_DELTA_BREAK_B);
+	}
+
+	/*
+	 * IP-OCTAL has different addresses to copy its IRQ vector.
+	 * Depending of the carrier these addresses are accesible or not.
+	 * More info in the datasheet.
+	 */
+	ipoctal->dev->ops->request_irq(ipoctal->dev, vector,
+				       ipoctal_irq_handler, ipoctal);
+	ipoctal->dev->ops->write8(ipoctal->dev, IPACK_ID_SPACE, 0, vector);
+
+	/* Register the TTY device */
+
+	/* Each IP-OCTAL channel is a TTY port */
+	tty = alloc_tty_driver(NR_CHANNELS);
+
+	if (!tty) {
+		res = -ENOMEM;
+		goto out_unregister_slot_unmap;
+	}
+
+	/* Fill struct tty_driver with ipoctal data */
+	tty->owner = THIS_MODULE;
+	tty->driver_name = "ipoctal";
+	sprintf(name, "ipoctal.%d.%d.", bus_nr, slot);
+	tty->name = name;
+	tty->major = 0;
+
+	tty->minor_start = 0;
+	tty->type = TTY_DRIVER_TYPE_SERIAL;
+	tty->subtype = SERIAL_TYPE_NORMAL;
+	tty->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	tty->init_termios = tty_std_termios;
+	tty->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+	tty->init_termios.c_ispeed = 9600;
+	tty->init_termios.c_ospeed = 9600;
+
+	tty_set_operations(tty, &ipoctal_fops);
+	res = tty_register_driver(tty);
+	if (res) {
+		pr_err("Can't register tty driver.\n");
+		put_tty_driver(tty);
+		goto out_unregister_slot_unmap;
+	}
+
+	/* Save struct tty_driver for use it when uninstalling the device */
+	ipoctal->tty_drv = tty;
+
+	for (i = 0; i < NR_CHANNELS; i++) {
+		tty_port_init(&ipoctal->tty_port[i]);
+		tty_port_alloc_xmit_buf(&ipoctal->tty_port[i]);
+		ipoctal->tty_port[i].ops = &ipoctal_tty_port_ops;
+
+		ipoctal_reset_stats(&ipoctal->chan_stats[i]);
+		ipoctal->nb_bytes[i] = 0;
+		init_waitqueue_head(&ipoctal->queue[i]);
+		ipoctal->error_flag[i] = UART_NOERROR;
+
+		spin_lock_init(&ipoctal->lock[i]);
+		ipoctal->pointer_read[i] = 0;
+		ipoctal->pointer_write[i] = 0;
+		ipoctal->nb_bytes[i] = 0;
+		tty_register_device(tty, i, NULL);
+
+		/*
+		 * Enable again the RX. TX will be enabled when
+		 * there is something to send
+		 */
+		ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[i].u.w.cr,
+				     CR_ENABLE_RX);
+	}
+
+	return 0;
+
+out_unregister_slot_unmap:
+	ipoctal->dev->ops->unmap_space(ipoctal->dev, IPACK_ID_SPACE);
+out_unregister_io_space:
+	ipoctal->dev->ops->unmap_space(ipoctal->dev, IPACK_IO_SPACE);
+out_unregister_id_space:
+	ipoctal->dev->ops->unmap_space(ipoctal->dev, IPACK_MEM_SPACE);
+	return res;
+}
+
+static inline int ipoctal_copy_write_buffer(struct ipoctal *ipoctal,
+					    unsigned int channel,
+					    const unsigned char *buf,
+					    int count)
+{
+	unsigned long flags;
+	int i;
+	unsigned int *pointer_read = &ipoctal->pointer_read[channel];
+
+	/* Copy the bytes from the user buffer to the internal one */
+	for (i = 0; i < count; i++) {
+		if (i <= (PAGE_SIZE - ipoctal->nb_bytes[channel])) {
+			spin_lock_irqsave(&ipoctal->lock[channel], flags);
+			ipoctal->tty_port[channel].xmit_buf[*pointer_read] = buf[i];
+			*pointer_read = (*pointer_read + 1) % PAGE_SIZE;
+			ipoctal->nb_bytes[channel]++;
+			spin_unlock_irqrestore(&ipoctal->lock[channel], flags);
+		} else {
+			break;
+		}
+	}
+	return i;
+}
+
+static int ipoctal_write(struct ipoctal *ipoctal, unsigned int channel,
+			 const unsigned char *buf, int count)
+{
+	ipoctal->nb_bytes[channel] = 0;
+	ipoctal->count_wr[channel] = 0;
+
+	ipoctal_copy_write_buffer(ipoctal, channel, buf, count);
+
+	ipoctal->error_flag[channel] = UART_NOERROR;
+
+	/* As the IP-OCTAL 485 only supports half duplex, do it manually */
+	if (ipoctal->board_id == IP_OCTAL_485_ID) {
+		ipoctal_write_io_reg(ipoctal,
+				     &ipoctal->chan_regs[channel].u.w.cr,
+				     CR_DISABLE_RX);
+		ipoctal_write_cr_cmd(ipoctal,
+				     &ipoctal->chan_regs[channel].u.w.cr,
+				     CR_CMD_ASSERT_RTSN);
+	}
+
+	/*
+	 * Send a packet and then disable TX to avoid failure after several send
+	 * operations
+	 */
+	ipoctal_write_io_reg(ipoctal,
+			     &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_ENABLE_TX);
+	wait_event_interruptible(ipoctal->queue[channel], ipoctal->write);
+	ipoctal_write_io_reg(ipoctal,
+			     &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_DISABLE_TX);
+
+	ipoctal->write = 0;
+	return ipoctal->count_wr[channel];
+}
+
+static int ipoctal_write_tty(struct tty_struct *tty,
+			     const unsigned char *buf, int count)
+{
+	unsigned int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	return ipoctal_write(ipoctal, channel, buf, count);
+}
+
+static int ipoctal_write_room(struct tty_struct *tty)
+{
+	int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	return PAGE_SIZE - ipoctal->nb_bytes[channel];
+}
+
+static int ipoctal_chars_in_buffer(struct tty_struct *tty)
+{
+	int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	return ipoctal->nb_bytes[channel];
+}
+
+static void ipoctal_set_termios(struct tty_struct *tty,
+				struct ktermios *old_termios)
+{
+	unsigned int cflag;
+	unsigned char mr1 = 0;
+	unsigned char mr2 = 0;
+	unsigned char csr = 0;
+	unsigned int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+	speed_t baud;
+
+	cflag = tty->termios->c_cflag;
+
+	/* Disable and reset everything before change the setup */
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_DISABLE_RX | CR_DISABLE_TX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_RX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_TX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_ERR_STATUS);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_MR);
+
+	/* Set Bits per chars */
+	switch (cflag & CSIZE) {
+	case CS6:
+		mr1 |= MR1_CHRL_6_BITS;
+		break;
+	case CS7:
+		mr1 |= MR1_CHRL_7_BITS;
+		break;
+	case CS8:
+	default:
+		mr1 |= MR1_CHRL_8_BITS;
+		/* By default, select CS8 */
+		tty->termios->c_cflag = (cflag & ~CSIZE) | CS8;
+		break;
+	}
+
+	/* Set Parity */
+	if (cflag & PARENB)
+		if (cflag & PARODD)
+			mr1 |= MR1_PARITY_ON | MR1_PARITY_ODD;
+		else
+			mr1 |= MR1_PARITY_ON | MR1_PARITY_EVEN;
+	else
+		mr1 |= MR1_PARITY_OFF;
+
+	/* Mark or space parity is not supported */
+	tty->termios->c_cflag &= ~CMSPAR;
+
+	/* Set stop bits */
+	if (cflag & CSTOPB)
+		mr2 |= MR2_STOP_BITS_LENGTH_2;
+	else
+		mr2 |= MR2_STOP_BITS_LENGTH_1;
+
+	/* Set the flow control */
+	switch (ipoctal->board_id) {
+	case IP_OCTAL_232_ID:
+		if (cflag & CRTSCTS) {
+			mr1 |= MR1_RxRTS_CONTROL_ON;
+			mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_ON;
+			ipoctal->chan_config[channel].flow_control = 1;
+		} else {
+			mr1 |= MR1_RxRTS_CONTROL_OFF;
+			mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_OFF;
+			ipoctal->chan_config[channel].flow_control = 0;
+		}
+		break;
+	case IP_OCTAL_422_ID:
+		mr1 |= MR1_RxRTS_CONTROL_OFF;
+		mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_OFF;
+		ipoctal->chan_config[channel].flow_control = 0;
+		break;
+	case IP_OCTAL_485_ID:
+		mr1 |= MR1_RxRTS_CONTROL_OFF;
+		mr2 |= MR2_TxRTS_CONTROL_ON | MR2_CTS_ENABLE_TX_OFF;
+		ipoctal->chan_config[channel].flow_control = 0;
+		break;
+	default:
+		return;
+		break;
+	}
+
+	baud = tty_get_baud_rate(tty);
+	tty_termios_encode_baud_rate(tty->termios, baud, baud);
+
+	/* Set baud rate */
+	switch (tty->termios->c_ospeed) {
+	case 75:
+		csr |= TX_CLK_75 | RX_CLK_75;
+		break;
+	case 110:
+		csr |= TX_CLK_110 | RX_CLK_110;
+		break;
+	case 150:
+		csr |= TX_CLK_150 | RX_CLK_150;
+		break;
+	case 300:
+		csr |= TX_CLK_300 | RX_CLK_300;
+		break;
+	case 600:
+		csr |= TX_CLK_600 | RX_CLK_600;
+		break;
+	case 1200:
+		csr |= TX_CLK_1200 | RX_CLK_1200;
+		break;
+	case 1800:
+		csr |= TX_CLK_1800 | RX_CLK_1800;
+		break;
+	case 2000:
+		csr |= TX_CLK_2000 | RX_CLK_2000;
+		break;
+	case 2400:
+		csr |= TX_CLK_2400 | RX_CLK_2400;
+		break;
+	case 4800:
+		csr |= TX_CLK_4800  | RX_CLK_4800;
+		break;
+	case 9600:
+		csr |= TX_CLK_9600  | RX_CLK_9600;
+		break;
+	case 19200:
+		csr |= TX_CLK_19200 | RX_CLK_19200;
+		break;
+	case 38400:
+	default:
+		csr |= TX_CLK_38400 | RX_CLK_38400;
+		/* In case of default, we establish 38400 bps */
+		tty_termios_encode_baud_rate(tty->termios, 38400, 38400);
+		break;
+	}
+
+	mr1 |= MR1_ERROR_CHAR;
+	mr1 |= MR1_RxINT_RxRDY;
+
+	/* Write the control registers */
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.mr, mr1);
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.mr, mr2);
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.csr, csr);
+
+	/* save the setup in the structure */
+	ipoctal->chan_config[channel].baud = tty_get_baud_rate(tty);
+	ipoctal->chan_config[channel].bits_per_char = cflag & CSIZE;
+	ipoctal->chan_config[channel].parity = cflag & PARENB;
+	ipoctal->chan_config[channel].stop_bits = cflag & CSTOPB;
+
+	/* Enable again the RX */
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_ENABLE_RX);
+}
+
+static void ipoctal_hangup(struct tty_struct *tty)
+{
+	unsigned long flags;
+	int channel = tty->index;
+	struct ipoctal *ipoctal = tty->driver_data;
+
+	if (ipoctal == NULL)
+		return;
+
+	spin_lock_irqsave(&ipoctal->lock[channel], flags);
+	ipoctal->nb_bytes[channel] = 0;
+	ipoctal->pointer_read[channel] = 0;
+	ipoctal->pointer_write[channel] = 0;
+	spin_unlock_irqrestore(&ipoctal->lock[channel], flags);
+
+	tty_port_hangup(&ipoctal->tty_port[channel]);
+
+	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_DISABLE_RX | CR_DISABLE_TX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_RX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_TX);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_ERR_STATUS);
+	ipoctal_write_cr_cmd(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
+			     CR_CMD_RESET_MR);
+
+	clear_bit(ASYNCB_INITIALIZED, &ipoctal->tty_port[channel].flags);
+	wake_up_interruptible(&ipoctal->tty_port[channel].open_wait);
+}
+
+static const struct tty_operations ipoctal_fops = {
+	.ioctl =		NULL,
+	.open =			ipoctal_open,
+	.close =		ipoctal_close,
+	.write =		ipoctal_write_tty,
+	.set_termios =		ipoctal_set_termios,
+	.write_room =		ipoctal_write_room,
+	.chars_in_buffer =	ipoctal_chars_in_buffer,
+	.get_icount =		ipoctal_get_icount,
+	.hangup =		ipoctal_hangup,
+};
+
+static int ipoctal_match(struct ipack_device *dev)
+{
+	int res;
+	unsigned char board_id;
+
+	res = dev->ops->map_space(dev, 0, IPACK_ID_SPACE);
+	if (res)
+		return res;
+
+	res = ipoctal_check_model(dev, &board_id);
+	dev->ops->unmap_space(dev, IPACK_ID_SPACE);
+	return res;
+}
+
+static int ipoctal_probe(struct ipack_device *dev)
+{
+	int res;
+	struct ipoctal *ipoctal;
+
+	ipoctal = kzalloc(sizeof(struct ipoctal), GFP_KERNEL);
+	if (ipoctal == NULL)
+		return -ENOMEM;
+
+	ipoctal->dev = dev;
+	res = ipoctal_inst_slot(ipoctal, dev->bus_nr, dev->slot, dev->irq);
+	if (res)
+		goto out_uninst;
+
+	list_add_tail(&ipoctal->list, &ipoctal_list);
+	return 0;
+
+out_uninst:
+	kfree(ipoctal);
+	return res;
+}
+
+static void __ipoctal_remove(struct ipoctal *ipoctal)
+{
+	int i;
+
+	for (i = 0; i < NR_CHANNELS; i++) {
+		tty_unregister_device(ipoctal->tty_drv, i);
+		tty_port_free_xmit_buf(&ipoctal->tty_port[i]);
+	}
+
+	tty_unregister_driver(ipoctal->tty_drv);
+	put_tty_driver(ipoctal->tty_drv);
+
+	/* Tell the carrier board to free all the resources for this device */
+	if (ipoctal->dev->ops->remove_device != NULL)
+		ipoctal->dev->ops->remove_device(ipoctal->dev);
+
+	list_del(&ipoctal->list);
+	kfree(ipoctal);
+}
+
+static void ipoctal_remove(struct ipack_device *device)
+{
+	struct ipoctal *ipoctal, *next;
+
+	list_for_each_entry_safe(ipoctal, next, &ipoctal_list, list) {
+		if (ipoctal->dev == device)
+			__ipoctal_remove(ipoctal);
+	}
+}
+
+static struct ipack_driver_ops ipoctal_drv_ops = {
+	.match = ipoctal_match,
+	.probe = ipoctal_probe,
+	.remove = ipoctal_remove,
+};
+
+static int __init ipoctal_init(void)
+{
+	driver.owner = THIS_MODULE;
+	driver.ops = &ipoctal_drv_ops;
+	driver.driver.name = KBUILD_MODNAME;
+	ipack_driver_register(&driver);
+	return 0;
+}
+
+static void __exit ipoctal_exit(void)
+{
+	struct ipoctal *p, *next;
+
+	list_for_each_entry_safe(p, next, &ipoctal_list, list)
+		__ipoctal_remove(p);
+
+	ipack_driver_unregister(&driver);
+}
+
+MODULE_DESCRIPTION("IP-Octal 232, 422 and 485 device driver");
+MODULE_LICENSE("GPL");
+
+module_init(ipoctal_init);
+module_exit(ipoctal_exit);

drivers/staging/ipack/devices/ipoctal.h

@@ -0,0 +1,81 @@
+/**
+ * ipoctal.h
+ *
+ * driver for the IPOCTAL boards
+ * Copyright (c) 2009 Nicolas Serafini, EIC2 SA
+ * Copyright (c) 2010,2011 Samuel Iglesias Gonsalvez <siglesia@cern.ch>, CERN
+ * Copyright (c) 2012 Samuel Iglesias Gonsalvez <siglesias@igalia.com>, Igalia
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#ifndef _IPOCTAL_H
+#define _IPOCTAL_H_
+
+#define NR_CHANNELS		8
+#define IPOCTAL_MAX_BOARDS	16
+#define MAX_DEVICES		(NR_CHANNELS * IPOCTAL_MAX_BOARDS)
+#define RELEVANT_IFLAG(iflag) ((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
+
+/**
+ * enum uart_parity_e - UART supported parity.
+ */
+enum uart_parity_e {
+	UART_NONE  = 0,
+	UART_ODD   = 1,
+	UART_EVEN  = 2,
+};
+
+/**
+ * enum uart_error - UART error type
+ *
+ */
+enum uart_error	{
+	UART_NOERROR = 0,      /* No error during transmission */
+	UART_TIMEOUT = 1 << 0, /* Timeout error */
+	UART_OVERRUN = 1 << 1, /* Overrun error */
+	UART_PARITY  = 1 << 2, /* Parity error */
+	UART_FRAMING = 1 << 3, /* Framing error */
+	UART_BREAK   = 1 << 4, /* Received break */
+};
+
+/**
+ * struct ipoctal_config - Serial configuration
+ *
+ * @baud: Baud rate
+ * @stop_bits: Stop bits (1 or 2)
+ * @bits_per_char: data size in bits
+ * @parity
+ * @flow_control: Flow control management (RTS/CTS) (0 disabled, 1 enabled)
+ */
+struct ipoctal_config {
+	unsigned int baud;
+	unsigned int stop_bits;
+	unsigned int bits_per_char;
+	unsigned short parity;
+	unsigned int flow_control;
+};
+
+/**
+ * struct ipoctal_stats -- Stats since last reset
+ *
+ * @tx: Number of transmitted bytes
+ * @rx: Number of received bytes
+ * @overrun: Number of overrun errors
+ * @parity_err: Number of parity errors
+ * @framing_err: Number of framing errors
+ * @rcv_break: Number of break received
+ */
+struct ipoctal_stats {
+	unsigned long tx;
+	unsigned long rx;
+	unsigned long overrun_err;
+	unsigned long parity_err;
+	unsigned long framing_err;
+	unsigned long rcv_break;
+};
+
+#endif /* _IPOCTAL_H_ */

drivers/staging/ipack/devices/scc2698.h

@@ -0,0 +1,229 @@
+/*
+ * scc2698.h
+ *
+ * driver for the IPOCTAL boards
+ * Copyright (c) 2009 Nicolas Serafini, EIC2 SA
+ * Copyright (c) 2010,2011 Samuel Iglesias Gonsalvez <siglesia@cern.ch>, CERN
+ * Copyright (c) 2012 Samuel Iglesias Gonsalvez <siglesias@igalia.com>, Igalia
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#ifndef SCC2698_H_
+#define SCC2698_H_
+
+/*
+ * struct scc2698_channel - Channel access to scc2698 IO
+ *
+ * dn value are only spacer.
+ *
+ */
+struct scc2698_channel {
+	union {
+		struct {
+			unsigned char d0, mr;  /* Mode register 1/2*/
+			unsigned char d1, sr;  /* Status register */
+			unsigned char d2, r1;  /* reserved */
+			unsigned char d3, rhr; /* Receive holding register (R) */
+			unsigned char junk[8]; /* other crap for block control */
+		} r; /* Read access */
+		struct {
+			unsigned char d0, mr;  /* Mode register 1/2 */
+			unsigned char d1, csr; /* Clock select register */
+			unsigned char d2, cr;  /* Command register */
+			unsigned char d3, thr; /* Transmit holding register */
+			unsigned char junk[8]; /* other crap for block control */
+		} w; /* Write access */
+	} u;
+};
+
+/*
+ * struct scc2698_block - Block access to scc2698 IO
+ *
+ * The scc2698 contain 4 block.
+ * Each block containt two channel a and b.
+ * dn value are only spacer.
+ *
+ */
+struct scc2698_block {
+	union {
+		struct {
+			unsigned char d0, mra;  /* Mode register 1/2 (a) */
+			unsigned char d1, sra;  /* Status register (a) */
+			unsigned char d2, r1;   /* reserved */
+			unsigned char d3, rhra; /* Receive holding register (a) */
+			unsigned char d4, ipcr; /* Input port change register of block */
+			unsigned char d5, isr;  /* Interrupt status register of block */
+			unsigned char d6, ctur; /* Counter timer upper register of block */
+			unsigned char d7, ctlr; /* Counter timer lower register of block */
+			unsigned char d8, mrb;  /* Mode register 1/2 (b) */
+			unsigned char d9, srb;  /* Status register (b) */
+			unsigned char da, r2;   /* reserved */
+			unsigned char db, rhrb; /* Receive holding register (b) */
+			unsigned char dc, r3;   /* reserved */
+			unsigned char dd, ip;   /* Input port register of block */
+			unsigned char de, ctg;  /* Start counter timer of block */
+			unsigned char df, cts;  /* Stop counter timer of block */
+		} r; /* Read access */
+		struct {
+			unsigned char d0, mra;  /* Mode register 1/2 (a) */
+			unsigned char d1, csra; /* Clock select register (a) */
+			unsigned char d2, cra;  /* Command register (a) */
+			unsigned char d3, thra; /* Transmit holding register (a) */
+			unsigned char d4, acr;  /* Auxiliary control register of block */
+			unsigned char d5, imr;  /* Interrupt mask register of block  */
+			unsigned char d6, ctu;  /* Counter timer upper register of block */
+			unsigned char d7, ctl;  /* Counter timer lower register of block */
+			unsigned char d8, mrb;  /* Mode register 1/2 (b) */
+			unsigned char d9, csrb; /* Clock select register (a) */
+			unsigned char da, crb;  /* Command register (b) */
+			unsigned char db, thrb; /* Transmit holding register (b) */
+			unsigned char dc, r1;   /* reserved */
+			unsigned char dd, opcr; /* Output port configuration register of block */
+			unsigned char de, r2;   /* reserved */
+			unsigned char df, r3;   /* reserved */
+		} w; /* Write access */
+	} u;
+} ;
+
+#define MR1_CHRL_5_BITS             (0x0 << 0)
+#define MR1_CHRL_6_BITS             (0x1 << 0)
+#define MR1_CHRL_7_BITS             (0x2 << 0)
+#define MR1_CHRL_8_BITS             (0x3 << 0)
+#define MR1_PARITY_EVEN             (0x1 << 2)
+#define MR1_PARITY_ODD              (0x0 << 2)
+#define MR1_PARITY_ON               (0x0 << 3)
+#define MR1_PARITY_FORCE            (0x1 << 3)
+#define MR1_PARITY_OFF              (0x2 << 3)
+#define MR1_PARITY_SPECIAL          (0x3 << 3)
+#define MR1_ERROR_CHAR              (0x0 << 5)
+#define MR1_ERROR_BLOCK             (0x1 << 5)
+#define MR1_RxINT_RxRDY             (0x0 << 6)
+#define MR1_RxINT_FFULL             (0x1 << 6)
+#define MR1_RxRTS_CONTROL_ON        (0x1 << 7)
+#define MR1_RxRTS_CONTROL_OFF       (0x0 << 7)
+
+#define MR2_STOP_BITS_LENGTH_1      (0x7 << 0)
+#define MR2_STOP_BITS_LENGTH_2      (0xF << 0)
+#define MR2_CTS_ENABLE_TX_ON        (0x1 << 4)
+#define MR2_CTS_ENABLE_TX_OFF       (0x0 << 4)
+#define MR2_TxRTS_CONTROL_ON        (0x1 << 5)
+#define MR2_TxRTS_CONTROL_OFF       (0x0 << 5)
+#define MR2_CH_MODE_NORMAL          (0x0 << 6)
+#define MR2_CH_MODE_ECHO            (0x1 << 6)
+#define MR2_CH_MODE_LOCAL           (0x2 << 6)
+#define MR2_CH_MODE_REMOTE          (0x3 << 6)
+
+#define CR_ENABLE_RX                (0x1 << 0)
+#define CR_DISABLE_RX               (0x1 << 1)
+#define CR_ENABLE_TX                (0x1 << 2)
+#define CR_DISABLE_TX               (0x1 << 3)
+#define CR_CMD_RESET_MR             (0x1 << 4)
+#define CR_CMD_RESET_RX             (0x2 << 4)
+#define CR_CMD_RESET_TX             (0x3 << 4)
+#define CR_CMD_RESET_ERR_STATUS     (0x4 << 4)
+#define CR_CMD_RESET_BREAK_CHANGE   (0x5 << 4)
+#define CR_CMD_START_BREAK          (0x6 << 4)
+#define CR_CMD_STOP_BREAK           (0x7 << 4)
+#define CR_CMD_ASSERT_RTSN          (0x8 << 4)
+#define CR_CMD_NEGATE_RTSN          (0x9 << 4)
+#define CR_CMD_SET_TIMEOUT_MODE     (0xA << 4)
+#define CR_CMD_DISABLE_TIMEOUT_MODE (0xC << 4)
+
+#define SR_RX_READY                 (0x1 << 0)
+#define SR_FIFO_FULL                (0x1 << 1)
+#define SR_TX_READY                 (0x1 << 2)
+#define SR_TX_EMPTY                 (0x1 << 3)
+#define SR_OVERRUN_ERROR            (0x1 << 4)
+#define SR_PARITY_ERROR             (0x1 << 5)
+#define SR_FRAMING_ERROR            (0x1 << 6)
+#define SR_RECEIVED_BREAK           (0x1 << 7)
+
+#define SR_ERROR                    (0xF0)
+
+#define ACR_DELTA_IP0_IRQ_EN        (0x1 << 0)
+#define ACR_DELTA_IP1_IRQ_EN        (0x1 << 1)
+#define ACR_DELTA_IP2_IRQ_EN        (0x1 << 2)
+#define ACR_DELTA_IP3_IRQ_EN        (0x1 << 3)
+#define ACR_CT_Mask                 (0x7 << 4)
+#define ACR_CExt                    (0x0 << 4)
+#define ACR_CTxCA                   (0x1 << 4)
+#define ACR_CTxCB                   (0x2 << 4)
+#define ACR_CClk16                  (0x3 << 4)
+#define ACR_TExt                    (0x4 << 4)
+#define ACR_TExt16                  (0x5 << 4)
+#define ACR_TClk                    (0x6 << 4)
+#define ACR_TClk16                  (0x7 << 4)
+#define ACR_BRG_SET1                (0x0 << 7)
+#define ACR_BRG_SET2                (0x1 << 7)
+
+#define TX_CLK_75                   (0x0 << 0)
+#define TX_CLK_110                  (0x1 << 0)
+#define TX_CLK_38400                (0x2 << 0)
+#define TX_CLK_150                  (0x3 << 0)
+#define TX_CLK_300                  (0x4 << 0)
+#define TX_CLK_600                  (0x5 << 0)
+#define TX_CLK_1200                 (0x6 << 0)
+#define TX_CLK_2000                 (0x7 << 0)
+#define TX_CLK_2400                 (0x8 << 0)
+#define TX_CLK_4800                 (0x9 << 0)
+#define TX_CLK_1800                 (0xA << 0)
+#define TX_CLK_9600                 (0xB << 0)
+#define TX_CLK_19200                (0xC << 0)
+#define RX_CLK_75                   (0x0 << 4)
+#define RX_CLK_110                  (0x1 << 4)
+#define RX_CLK_38400                (0x2 << 4)
+#define RX_CLK_150                  (0x3 << 4)
+#define RX_CLK_300                  (0x4 << 4)
+#define RX_CLK_600                  (0x5 << 4)
+#define RX_CLK_1200                 (0x6 << 4)
+#define RX_CLK_2000                 (0x7 << 4)
+#define RX_CLK_2400                 (0x8 << 4)
+#define RX_CLK_4800                 (0x9 << 4)
+#define RX_CLK_1800                 (0xA << 4)
+#define RX_CLK_9600                 (0xB << 4)
+#define RX_CLK_19200                (0xC << 4)
+
+#define OPCR_MPOa_RTSN              (0x0 << 0)
+#define OPCR_MPOa_C_TO              (0x1 << 0)
+#define OPCR_MPOa_TxC1X             (0x2 << 0)
+#define OPCR_MPOa_TxC16X            (0x3 << 0)
+#define OPCR_MPOa_RxC1X             (0x4 << 0)
+#define OPCR_MPOa_RxC16X            (0x5 << 0)
+#define OPCR_MPOa_TxRDY             (0x6 << 0)
+#define OPCR_MPOa_RxRDY_FF          (0x7 << 0)
+
+#define OPCR_MPOb_RTSN              (0x0 << 4)
+#define OPCR_MPOb_C_TO              (0x1 << 4)
+#define OPCR_MPOb_TxC1X             (0x2 << 4)
+#define OPCR_MPOb_TxC16X            (0x3 << 4)
+#define OPCR_MPOb_RxC1X             (0x4 << 4)
+#define OPCR_MPOb_RxC16X            (0x5 << 4)
+#define OPCR_MPOb_TxRDY             (0x6 << 4)
+#define OPCR_MPOb_RxRDY_FF          (0x7 << 4)
+
+#define OPCR_MPP_INPUT              (0x0 << 7)
+#define OPCR_MPP_OUTPUT             (0x1 << 7)
+
+#define IMR_TxRDY_A                 (0x1 << 0)
+#define IMR_RxRDY_FFULL_A           (0x1 << 1)
+#define IMR_DELTA_BREAK_A           (0x1 << 2)
+#define IMR_COUNTER_READY           (0x1 << 3)
+#define IMR_TxRDY_B                 (0x1 << 4)
+#define IMR_RxRDY_FFULL_B           (0x1 << 5)
+#define IMR_DELTA_BREAK_B           (0x1 << 6)
+#define IMR_INPUT_PORT_CHANGE       (0x1 << 7)
+
+#define ISR_TxRDY_A                 (0x1 << 0)
+#define ISR_RxRDY_FFULL_A           (0x1 << 1)
+#define ISR_DELTA_BREAK_A           (0x1 << 2)
+#define ISR_COUNTER_READY           (0x1 << 3)
+#define ISR_TxRDY_B                 (0x1 << 4)
+#define ISR_RxRDY_FFULL_B           (0x1 << 5)
+#define ISR_DELTA_BREAK_B           (0x1 << 6)
+#define ISR_INPUT_PORT_CHANGE       (0x1 << 7)
+
+#endif /* SCC2698_H_ */