sh: pci: Move se7780 INTC fixups out of pci-sh7780.c.

These fixups belong in the board INTC setup code, not in the middle of
pci-sh7780.c.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

arch/sh/boards/mach-se/7780/irq.c

@@ -12,10 +12,13 @@
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
-#include <asm/irq.h>
-#include <asm/io.h>
+#include <linux/irq.h>
+#include <linux/io.h>
 #include <mach-se/mach/se7780.h>
 
+#define INTC_BASE	0xffd00000
+#define INTC_ICR1	(INTC_BASE+0x1c)
+
 /*
  * Initialize IRQ setting
  */
@@ -43,4 +46,7 @@ void __init init_se7780_IRQ(void)
 	ctrl_outw((IRQPIN_PCCPW << IRQPOS_PCCPW), FPGA_INTSEL3);
 
 	plat_irq_setup_pins(IRQ_MODE_IRQ); /* install handlers for IRQ0-7 */
+
+	/* ICR1: detect low level(for 2ndcut) */
+	ctrl_outl(0xAAAA0000, INTC_ICR1);
 }

arch/sh/drivers/pci/pci-sh7780.c

@@ -22,20 +22,6 @@
 #include <linux/delay.h>
 #include "pci-sh4.h"
 
-#define INTC_BASE	0xffd00000
-#define INTC_ICR0	(INTC_BASE+0x0)
-#define INTC_ICR1	(INTC_BASE+0x1c)
-#define INTC_INTPRI	(INTC_BASE+0x10)
-#define INTC_INTREQ	(INTC_BASE+0x24)
-#define INTC_INTMSK0	(INTC_BASE+0x44)
-#define INTC_INTMSK1	(INTC_BASE+0x48)
-#define INTC_INTMSK2	(INTC_BASE+0x40080)
-#define INTC_INTMSKCLR0	(INTC_BASE+0x64)
-#define INTC_INTMSKCLR1	(INTC_BASE+0x68)
-#define INTC_INTMSKCLR2	(INTC_BASE+0x40084)
-#define INTC_INT2MSKR	(INTC_BASE+0x40038)
-#define INTC_INT2MSKCR	(INTC_BASE+0x4003c)
-
 /*
  * Initialization. Try all known PCI access methods. Note that we support
  * using both PCI BIOS and direct access: in such cases, we use I/O ports
@@ -75,16 +61,6 @@ int __init sh7780_pci_init(struct pci_channel *chan)
 		return -ENODEV;
 	}
 
-	/* Setup the INTC */
-	if (mach_is_7780se()) {
-		/* ICR0: IRL=use separately */
-		ctrl_outl(0x00C00020, INTC_ICR0);
-		/* ICR1: detect low level(for 2ndcut) */
-		ctrl_outl(0xAAAA0000, INTC_ICR1);
-		/* INTPRI: priority=3(all) */
-		ctrl_outl(0x33333333, INTC_INTPRI);
-	}
-
 	if ((ret = sh4_pci_check_direct(chan)) != 0)
 		return ret;