staging: rtl8192u: fix read_nic_* functions

read_nic_*() functions are defined in r8192U_core.c.
They call internally usb_control_msg() to read the
nic registers and return the value read.
Following a remark made by Dan Carpenter, if usb_control_msg()
fails, the value returned will be invalid.

To accommodate for this, this patch changes the functions
to take a pointer as argument to set the value read and
return 0 on success and the error status on failure, so
that callers of read_nic_*() can check the return status.

Some other fixes introduced in read_nic_*() functions are:

The expressions (1<<EPROM_*_SHIFT) used to address and set
the individual bits of the eeprom register were replaced
with EPROM_*_BIT bitmasks to make the code more intuitive.
EPROM_*_BIT bitmasks were defined in r8192U_hw.h and
EPROM_*_SHIFT were removed.

In netdev_err(), which is called in case of failure,
the hardcoded function name in the error log message was
replaced with __func__ to reduce line size.
Also, from the error log message, it was omitted the word
"Timeout" and it is just reported the error code since the
failure can not only be due to timeout expiration but also
due to a memory allocation failure. In case of timeout
expiration, usb_start_wait_urb() prints an appropriate log
message when debug is enabled.

Finally, some minor fixes to the coding style were applied in
lines affected by the above changes, including the removal
of ifdef DEBUG_RX (the debugging of reads and writes of the
nic registers shall be done with explicit check on their
return status which will be added in a follow on patch).

Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/rtl8192u/r8180_93cx6.c

@@ -22,13 +22,15 @@
 
 void eprom_cs(struct net_device *dev, short bit)
 {
+	u8 cmdreg;
+
+	read_nic_byte_E(dev, EPROM_CMD, &cmdreg);
 	if (bit)
-		write_nic_byte_E(dev, EPROM_CMD,
-			       (1<<EPROM_CS_SHIFT) | \
-			       read_nic_byte_E(dev, EPROM_CMD)); //enable EPROM
+		/* enable EPROM */
+		write_nic_byte_E(dev, EPROM_CMD, cmdreg | EPROM_CS_BIT);
 	else
-		write_nic_byte_E(dev, EPROM_CMD, read_nic_byte_E(dev, EPROM_CMD)\
-			       & ~(1<<EPROM_CS_SHIFT)); //disable EPROM
+		/* disable EPROM */
+		write_nic_byte_E(dev, EPROM_CMD, cmdreg & ~EPROM_CS_BIT);
 
 	force_pci_posting(dev);
 	udelay(EPROM_DELAY);
@@ -37,12 +39,15 @@ void eprom_cs(struct net_device *dev, short bit)
 
 void eprom_ck_cycle(struct net_device *dev)
 {
-	write_nic_byte_E(dev, EPROM_CMD,
-		       (1<<EPROM_CK_SHIFT) | read_nic_byte_E(dev,EPROM_CMD));
+	u8 cmdreg;
+
+	read_nic_byte_E(dev, EPROM_CMD, &cmdreg);
+	write_nic_byte_E(dev, EPROM_CMD, cmdreg | EPROM_CK_BIT);
 	force_pci_posting(dev);
 	udelay(EPROM_DELAY);
-	write_nic_byte_E(dev, EPROM_CMD,
-		       read_nic_byte_E(dev, EPROM_CMD) & ~(1<<EPROM_CK_SHIFT));
+
+	read_nic_byte_E(dev, EPROM_CMD, &cmdreg);
+	write_nic_byte_E(dev, EPROM_CMD, cmdreg & ~EPROM_CK_BIT);
 	force_pci_posting(dev);
 	udelay(EPROM_DELAY);
 }
@@ -50,12 +55,13 @@ void eprom_ck_cycle(struct net_device *dev)
 
 void eprom_w(struct net_device *dev,short bit)
 {
+	u8 cmdreg;
+
+	read_nic_byte_E(dev, EPROM_CMD, &cmdreg);
 	if (bit)
-		write_nic_byte_E(dev, EPROM_CMD, (1<<EPROM_W_SHIFT) | \
-			       read_nic_byte_E(dev,EPROM_CMD));
+		write_nic_byte_E(dev, EPROM_CMD, cmdreg | EPROM_W_BIT);
 	else
-		write_nic_byte_E(dev, EPROM_CMD, read_nic_byte_E(dev,EPROM_CMD)\
-			       & ~(1<<EPROM_W_SHIFT));
+		write_nic_byte_E(dev, EPROM_CMD, cmdreg & ~EPROM_W_BIT);
 
 	force_pci_posting(dev);
 	udelay(EPROM_DELAY);
@@ -64,12 +70,14 @@ void eprom_w(struct net_device *dev,short bit)
 
 short eprom_r(struct net_device *dev)
 {
-	short bit;
+	u8 bit;
 
-	bit=(read_nic_byte_E(dev, EPROM_CMD) & (1<<EPROM_R_SHIFT) );
+	read_nic_byte_E(dev, EPROM_CMD, &bit);
 	udelay(EPROM_DELAY);
 
-	if (bit) return 1;
+	if (bit & EPROM_R_BIT)
+		return 1;
+
 	return 0;
 }
 

drivers/staging/rtl8192u/r8192U.h

@@ -1205,10 +1205,10 @@ short rtl8192_tx(struct net_device *dev, struct sk_buff *skb);
 u32 read_cam(struct net_device *dev, u8 addr);
 void write_cam(struct net_device *dev, u8 addr, u32 data);
 
-u8 read_nic_byte(struct net_device *dev, int x);
-u8 read_nic_byte_E(struct net_device *dev, int x);
-u32 read_nic_dword(struct net_device *dev, int x);
-u16 read_nic_word(struct net_device *dev, int x) ;
+int read_nic_byte(struct net_device *dev, int x, u8 *data);
+int read_nic_byte_E(struct net_device *dev, int x, u8 *data);
+int read_nic_dword(struct net_device *dev, int x, u32 *data);
+int read_nic_word(struct net_device *dev, int x, u16 *data);
 void write_nic_byte(struct net_device *dev, int x,u8 y);
 void write_nic_byte_E(struct net_device *dev, int x,u8 y);
 void write_nic_word(struct net_device *dev, int x,u16 y);

drivers/staging/rtl8192u/r8192U_core.c

@@ -258,8 +258,11 @@ void write_cam(struct net_device *dev, u8 addr, u32 data)
 
 u32 read_cam(struct net_device *dev, u8 addr)
 {
+	u32 data;
+
 	write_nic_dword(dev, RWCAM, 0x80000000|(addr&0xff));
-	return read_nic_dword(dev, 0xa8);
+	read_nic_dword(dev, 0xa8, &data);
+	return data;
 }
 
 void write_nic_byte_E(struct net_device *dev, int indx, u8 data)
@@ -276,21 +279,22 @@ void write_nic_byte_E(struct net_device *dev, int indx, u8 data)
 		netdev_err(dev, "write_nic_byte_E TimeOut! status: %d\n", status);
 }
 
-u8 read_nic_byte_E(struct net_device *dev, int indx)
+int read_nic_byte_E(struct net_device *dev, int indx, u8 *data)
 {
 	int status;
-	u8 data;
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
 	struct usb_device *udev = priv->udev;
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx|0xfe00, 0, &data, 1, HZ / 2);
+				 indx|0xfe00, 0, data, 1, HZ / 2);
 
-	if (status < 0)
-		netdev_err(dev, "read_nic_byte_E TimeOut! status: %d\n", status);
+	if (status < 0) {
+		netdev_err(dev, "%s failure status: %d\n", __func__, status);
+		return status;
+	}
 
-	return data;
+	return 0;
 }
 //as 92U has extend page from 4 to 16, so modify functions below.
 void write_nic_byte(struct net_device *dev, int indx, u8 data)
@@ -349,28 +353,28 @@ void write_nic_dword(struct net_device *dev, int indx, u32 data)
 
 
 
-u8 read_nic_byte(struct net_device *dev, int indx)
+int read_nic_byte(struct net_device *dev, int indx, u8 *data)
 {
-	u8 data;
 	int status;
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
 	struct usb_device *udev = priv->udev;
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 (indx&0xff)|0xff00, (indx>>8)&0x0f, &data, 1, HZ / 2);
+				 (indx&0xff)|0xff00, (indx>>8)&0x0f, data, 1, HZ / 2);
 
-	if (status < 0)
-		netdev_err(dev, "read_nic_byte TimeOut! status: %d\n", status);
+	if (status < 0) {
+		netdev_err(dev, "%s failure status: %d\n", __func__, status);
+		return status;
+	}
 
-	return data;
+	return 0;
 }
 
 
 
-u16 read_nic_word(struct net_device *dev, int indx)
+int read_nic_word(struct net_device *dev, int indx, u16 *data)
 {
-	u16 data;
 	int status;
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
 	struct usb_device *udev = priv->udev;
@@ -378,34 +382,36 @@ u16 read_nic_word(struct net_device *dev, int indx)
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx&0xff)|0xff00, (indx>>8)&0x0f,
-				 &data, 2, HZ / 2);
+				 data, 2, HZ / 2);
 
-	if (status < 0)
-		netdev_err(dev, "read_nic_word TimeOut! status: %d\n", status);
+	if (status < 0) {
+		netdev_err(dev, "%s failure status: %d\n", __func__, status);
+		return status;
+	}
 
-	return data;
+	return 0;
 }
 
-u16 read_nic_word_E(struct net_device *dev, int indx)
+int read_nic_word_E(struct net_device *dev, int indx, u16 *data)
 {
-	u16 data;
 	int status;
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
 	struct usb_device *udev = priv->udev;
 
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
-				 indx|0xfe00, 0, &data, 2, HZ / 2);
+				 indx|0xfe00, 0, data, 2, HZ / 2);
 
-	if (status < 0)
-		netdev_err(dev, "read_nic_word TimeOut! status: %d\n", status);
+	if (status < 0) {
+		netdev_err(dev, "%s failure status: %d\n", __func__, status);
+		return status;
+	}
 
-	return data;
+	return 0;
 }
 
-u32 read_nic_dword(struct net_device *dev, int indx)
+int read_nic_dword(struct net_device *dev, int indx, u32 *data)
 {
-	u32 data;
 	int status;
 
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
@@ -414,12 +420,14 @@ u32 read_nic_dword(struct net_device *dev, int indx)
 	status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
 				 RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
 				 (indx&0xff)|0xff00, (indx>>8)&0x0f,
-				 &data, 4, HZ / 2);
+				 data, 4, HZ / 2);
 
-	if (status < 0)
-		netdev_err(dev, "read_nic_dword TimeOut! status:%d\n", status);
+	if (status < 0) {
+		netdev_err(dev, "%s failure status: %d\n", __func__, status);
+		return status;
+	}
 
-	return data;
+	return 0;
 }
 
 /* u8 read_phy_cck(struct net_device *dev, u8 adr); */
@@ -465,30 +473,37 @@ static int proc_get_registers(struct seq_file *m, void *v)
 {
 	struct net_device *dev = m->private;
 	int i, n, max = 0xff;
+	u8 byte_rd;
 
 	seq_puts(m, "\n####################page 0##################\n ");
 
 	for (n = 0; n <= max;) {
 		seq_printf(m, "\nD:  %2x > ", n);
 
-		for (i = 0; i < 16 && n <= max; i++, n++)
-			seq_printf(m, "%2x ", read_nic_byte(dev, 0x000|n));
+		for (i = 0; i < 16 && n <= max; i++, n++) {
+			read_nic_byte(dev, 0x000|n, &byte_rd);
+			seq_printf(m, "%2x ", byte_rd);
+		}
 	}
 
 	seq_puts(m, "\n####################page 1##################\n ");
 	for (n = 0; n <= max;) {
 		seq_printf(m, "\nD:  %2x > ", n);
 
-		for (i = 0; i < 16 && n <= max; i++, n++)
-			seq_printf(m, "%2x ", read_nic_byte(dev, 0x100|n));
+		for (i = 0; i < 16 && n <= max; i++, n++) {
+			read_nic_byte(dev, 0x100|n, &byte_rd);
+			seq_printf(m, "%2x ", byte_rd);
+		}
 	}
 
 	seq_puts(m, "\n####################page 3##################\n ");
 	for (n = 0; n <= max;) {
 		seq_printf(m, "\nD:  %2x > ", n);
 
-		for (i = 0; i < 16 && n <= max; i++, n++)
-			seq_printf(m, "%2x ", read_nic_byte(dev, 0x300|n));
+		for (i = 0; i < 16 && n <= max; i++, n++) {
+			read_nic_byte(dev, 0x300|n, &byte_rd);
+			seq_printf(m, "%2x ", byte_rd);
+		}
 	}
 
 	seq_putc(m, '\n');
@@ -683,11 +698,11 @@ void dump_eprom(struct net_device *dev)
 void rtl8192_set_mode(struct net_device *dev, int mode)
 {
 	u8 ecmd;
-	ecmd = read_nic_byte(dev, EPROM_CMD);
+	read_nic_byte(dev, EPROM_CMD, &ecmd);
 	ecmd = ecmd & ~EPROM_CMD_OPERATING_MODE_MASK;
 	ecmd = ecmd | (mode<<EPROM_CMD_OPERATING_MODE_SHIFT);
-	ecmd = ecmd & ~(1<<EPROM_CS_SHIFT);
-	ecmd = ecmd & ~(1<<EPROM_CK_SHIFT);
+	ecmd = ecmd & ~EPROM_CS_BIT;
+	ecmd = ecmd & ~EPROM_CK_BIT;
 	write_nic_byte(dev, EPROM_CMD, ecmd);
 }
 
@@ -697,7 +712,7 @@ void rtl8192_update_msr(struct net_device *dev)
 	struct r8192_priv *priv = ieee80211_priv(dev);
 	u8 msr;
 
-	msr  = read_nic_byte(dev, MSR);
+	read_nic_byte(dev, MSR, &msr);
 	msr &= ~MSR_LINK_MASK;
 
 	/* do not change in link_state != WLAN_LINK_ASSOCIATED.
@@ -810,7 +825,7 @@ void rtl8192_set_rxconf(struct net_device *dev)
 	struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
 	u32 rxconf;
 
-	rxconf = read_nic_dword(dev, RCR);
+	read_nic_dword(dev, RCR, &rxconf);
 	rxconf = rxconf & ~MAC_FILTER_MASK;
 	rxconf = rxconf | RCR_AMF;
 	rxconf = rxconf | RCR_ADF;
@@ -846,10 +861,6 @@ void rtl8192_set_rxconf(struct net_device *dev)
 	rxconf = rxconf | RCR_ONLYERLPKT;
 
 	write_nic_dword(dev, RCR, rxconf);
-
-#ifdef DEBUG_RX
-	DMESG("rxconf: %x %x", rxconf, read_nic_dword(dev, RCR));
-#endif
 }
 //wait to be removed
 void rtl8192_rx_enable(struct net_device *dev)
@@ -871,7 +882,7 @@ void rtl8192_rtx_disable(struct net_device *dev)
 	struct sk_buff *skb;
 	struct rtl8192_rx_info *info;
 
-	cmd = read_nic_byte(dev, CMDR);
+	read_nic_byte(dev, CMDR, &cmd);
 	write_nic_byte(dev, CMDR, cmd & ~(CR_TE|CR_RE));
 	force_pci_posting(dev);
 	mdelay(10);
@@ -1352,7 +1363,7 @@ void rtl8192_beacon_stop(struct net_device *dev)
 	u8 msr, msrm, msr2;
 	struct r8192_priv *priv = ieee80211_priv(dev);
 
-	msr  = read_nic_byte(dev, MSR);
+	read_nic_byte(dev, MSR, &msr);
 	msrm = msr & MSR_LINK_MASK;
 	msr2 = msr & ~MSR_LINK_MASK;
 
@@ -2049,7 +2060,7 @@ void rtl8192_link_change(struct net_device *dev)
 	/*update timing params*/
 	if (ieee->iw_mode == IW_MODE_INFRA || ieee->iw_mode == IW_MODE_ADHOC) {
 		u32 reg = 0;
-		reg = read_nic_dword(dev, RCR);
+		read_nic_dword(dev, RCR, &reg);
 		if (priv->ieee80211->state == IEEE80211_LINKED)
 			priv->ReceiveConfig = reg |= RCR_CBSSID;
 		else
@@ -2544,7 +2555,7 @@ static void rtl8192_get_eeprom_size(struct net_device *dev)
 	u16 curCR = 0;
 	struct r8192_priv *priv = ieee80211_priv(dev);
 	RT_TRACE(COMP_EPROM, "===========>%s()\n", __func__);
-	curCR = read_nic_word_E(dev, EPROM_CMD);
+	read_nic_word_E(dev, EPROM_CMD, &curCR);
 	RT_TRACE(COMP_EPROM, "read from Reg EPROM_CMD(%x):%x\n", EPROM_CMD, curCR);
 	//whether need I consider BIT5?
 	priv->epromtype = (curCR & Cmd9346CR_9356SEL) ? EPROM_93c56 : EPROM_93c46;
@@ -2896,7 +2907,7 @@ void rtl8192_hwconfig(struct net_device *dev)
 		ratr_value &= ~(RATE_ALL_OFDM_2SS);
 	write_nic_dword(dev, RATR0, ratr_value);
 	write_nic_byte(dev, UFWP, 1);
-	regTmp = read_nic_byte(dev, 0x313);
+	read_nic_byte(dev, 0x313, &regTmp);
 	regRRSR = ((regTmp) << 24) | (regRRSR & 0x00ffffff);
 	write_nic_dword(dev, RRSR, regRRSR);
 
@@ -2925,6 +2936,7 @@ bool rtl8192_adapter_start(struct net_device *dev)
 	u32 dwRegRead = 0;
 	bool init_status = true;
 	u8 SECR_value = 0x0;
+	u8 tmp;
 	RT_TRACE(COMP_INIT, "====>%s()\n", __func__);
 	priv->Rf_Mode = RF_OP_By_SW_3wire;
 	//for ASIC power on sequence
@@ -2938,7 +2950,7 @@ bool rtl8192_adapter_start(struct net_device *dev)
 	priv->pFirmware->firmware_status = FW_STATUS_0_INIT;
 	//config CPUReset Register
 	//Firmware Reset or not?
-	dwRegRead = read_nic_dword(dev, CPU_GEN);
+	read_nic_dword(dev, CPU_GEN, &dwRegRead);
 	if (priv->pFirmware->firmware_status == FW_STATUS_0_INIT)
 		dwRegRead |= CPU_GEN_SYSTEM_RESET; //do nothing here?
 	else if (priv->pFirmware->firmware_status == FW_STATUS_5_READY)
@@ -2953,7 +2965,7 @@ bool rtl8192_adapter_start(struct net_device *dev)
 	//Loopback mode or not
 	priv->LoopbackMode = RTL819xU_NO_LOOPBACK;
 
-	dwRegRead = read_nic_dword(dev, CPU_GEN);
+	read_nic_dword(dev, CPU_GEN, &dwRegRead);
 	if (priv->LoopbackMode == RTL819xU_NO_LOOPBACK)
 		dwRegRead = ((dwRegRead & CPU_GEN_NO_LOOPBACK_MSK) | CPU_GEN_NO_LOOPBACK_SET);
 	else if (priv->LoopbackMode == RTL819xU_MAC_LOOPBACK)
@@ -2967,7 +2979,8 @@ bool rtl8192_adapter_start(struct net_device *dev)
 	udelay(500);
 
 	//xiong add for new bitfile:usb suspend reset pin set to 1. //do we need?
-	write_nic_byte_E(dev, 0x5f, (read_nic_byte_E(dev, 0x5f)|0x20));
+	read_nic_byte_E(dev, 0x5f, &tmp);
+	write_nic_byte_E(dev, 0x5f, tmp|0x20);
 
 	//Set Hardware
 	rtl8192_hwconfig(dev);
@@ -3095,7 +3108,8 @@ bool rtl8192_adapter_start(struct net_device *dev)
 
 	if (priv->ResetProgress == RESET_TYPE_NORESET) {
 		//if D or C cut
-		u8 tmpvalue = read_nic_byte(dev, 0x301);
+		u8 tmpvalue;
+		read_nic_byte(dev, 0x301, &tmpvalue);
 		if (tmpvalue == 0x03) {
 			priv->bDcut = TRUE;
 			RT_TRACE(COMP_POWER_TRACKING, "D-cut\n");
@@ -3156,8 +3170,9 @@ static struct net_device_stats *rtl8192_stats(struct net_device *dev)
 bool HalTxCheckStuck819xUsb(struct net_device *dev)
 {
 	struct r8192_priv *priv = ieee80211_priv(dev);
-	u16		RegTxCounter = read_nic_word(dev, 0x128);
+	u16		RegTxCounter;
 	bool		bStuck = FALSE;
+	read_nic_word(dev, 0x128, &RegTxCounter);
 	RT_TRACE(COMP_RESET, "%s():RegTxCounter is %d,TxCounter is %d\n", __func__, RegTxCounter, priv->TxCounter);
 	if (priv->TxCounter == RegTxCounter)
 		bStuck = TRUE;
@@ -3204,10 +3219,11 @@ RESET_TYPE TxCheckStuck(struct net_device *dev)
 
 bool HalRxCheckStuck819xUsb(struct net_device *dev)
 {
-	u16	RegRxCounter = read_nic_word(dev, 0x130);
+	u16	RegRxCounter;
 	struct r8192_priv *priv = ieee80211_priv(dev);
 	bool bStuck = FALSE;
 	static u8	rx_chk_cnt;
+	read_nic_word(dev, 0x130, &RegRxCounter);
 	RT_TRACE(COMP_RESET, "%s(): RegRxCounter is %d,RxCounter is %d\n", __func__, RegRxCounter, priv->RxCounter);
 	// If rssi is small, we should check rx for long time because of bad rx.
 	// or maybe it will continuous silent reset every 2 seconds.
@@ -3494,7 +3510,7 @@ void CAM_read_entry(struct net_device *dev, u32 iIndex)
 
 		//Check polling bit is clear
 		while ((i--) >= 0) {
-			ulStatus = read_nic_dword(dev, RWCAM);
+			read_nic_dword(dev, RWCAM, &ulStatus);
 			if (ulStatus & BIT31)
 				continue;
 			else
@@ -3502,7 +3518,7 @@ void CAM_read_entry(struct net_device *dev, u32 iIndex)
 		}
 		write_nic_dword(dev, RWCAM, target_command);
 		RT_TRACE(COMP_SEC, "CAM_read_entry(): WRITE A0: %x \n", target_command);
-		target_content = read_nic_dword(dev, RCAMO);
+		read_nic_dword(dev, RCAMO, &target_content);
 		RT_TRACE(COMP_SEC, "CAM_read_entry(): WRITE A8: %x \n", target_content);
 	}
 	printk("\n");

drivers/staging/rtl8192u/r8192U_dm.c

@@ -480,7 +480,7 @@ static void dm_check_rate_adaptive(struct net_device *dev)
 		//
 		// Check whether updating of RATR0 is required
 		//
-		currentRATR = read_nic_dword(dev, RATR0);
+		read_nic_dword(dev, RATR0, &currentRATR);
 		if(targetRATR !=  currentRATR)
 		{
 			u32 ratr_value;
@@ -634,7 +634,7 @@ static void dm_TXPowerTrackingCallback_TSSI(struct net_device *dev)
 	//DbgPrint("hi, vivi, strange\n");
 	for(i = 0;i <= 30; i++)
 	{
-		Pwr_Flag = read_nic_byte(dev, 0x1ba);
+		read_nic_byte(dev, 0x1ba, &Pwr_Flag);
 
 		if (Pwr_Flag == 0)
 		{
@@ -642,9 +642,9 @@ static void dm_TXPowerTrackingCallback_TSSI(struct net_device *dev)
 			continue;
 		}
 #ifdef RTL8190P
-		Avg_TSSI_Meas = read_nic_word(dev, 0x1bc);
+		read_nic_word(dev, 0x1bc, &Avg_TSSI_Meas);
 #else
-		Avg_TSSI_Meas = read_nic_word(dev, 0x13c);
+		read_nic_word(dev, 0x13c, &Avg_TSSI_Meas);
 #endif
 		if(Avg_TSSI_Meas == 0)
 		{
@@ -655,12 +655,12 @@ static void dm_TXPowerTrackingCallback_TSSI(struct net_device *dev)
 		for(k = 0;k < 5; k++)
 		{
 #ifdef RTL8190P
-			tmp_report[k] = read_nic_byte(dev, 0x1d8+k);
+			read_nic_byte(dev, 0x1d8+k, &tmp_report[k]);
 #else
 			if(k !=4)
-				tmp_report[k] = read_nic_byte(dev, 0x134+k);
+				read_nic_byte(dev, 0x134+k, &tmp_report[k]);
 			else
-				tmp_report[k] = read_nic_byte(dev, 0x13e);
+				read_nic_byte(dev, 0x13e, &tmp_report[k]);
 #endif
 			RT_TRACE(COMP_POWER_TRACKING, "TSSI_report_value = %d\n", tmp_report[k]);
 		}
@@ -2397,6 +2397,7 @@ static void dm_initial_gain(
 	u8					initial_gain=0;
 	static u8				initialized, force_write;
 	static u32			reset_cnt;
+	u8				tmp;
 
 	if(dm_digtable.dig_algorithm_switch)
 	{
@@ -2437,7 +2438,8 @@ static void dm_initial_gain(
 		reset_cnt = priv->reset_count;
 	}
 
-	if(dm_digtable.pre_ig_value != read_nic_byte(dev, rOFDM0_XAAGCCore1))
+	read_nic_byte(dev, rOFDM0_XAAGCCore1, &tmp);
+	if (dm_digtable.pre_ig_value != tmp)
 		force_write = 1;
 
 	{
@@ -2727,7 +2729,8 @@ static void dm_check_edca_turbo(
 			// TODO:  Modified this part and try to set acm control in only 1 IO processing!!
 
 					PACI_AIFSN	pAciAifsn = (PACI_AIFSN)&(qos_parameters->aifs[0]);
-					u8		AcmCtrl = read_nic_byte(dev, AcmHwCtrl);
+					u8		AcmCtrl;
+					read_nic_byte(dev, AcmHwCtrl, &AcmCtrl);
 					if(pAciAifsn->f.ACM)
 					{ // ACM bit is 1.
 						AcmCtrl |= AcmHw_BeqEn;
@@ -2881,7 +2884,7 @@ static	void	dm_check_pbc_gpio(struct net_device *dev)
 	u8 tmp1byte;
 
 
-	tmp1byte = read_nic_byte(dev,GPI);
+	read_nic_byte(dev, GPI, &tmp1byte);
 	if(tmp1byte == 0xff)
 		return;
 
@@ -2933,7 +2936,7 @@ extern	void	dm_gpio_change_rf_callback(struct work_struct *work)
 		{
 			// 0x108 GPIO input register is read only
 			//set 0x108 B1= 1: RF-ON; 0: RF-OFF.
-			tmp1byte = read_nic_byte(dev,GPI);
+			read_nic_byte(dev, GPI, &tmp1byte);
 
 			eRfPowerStateToSet = (tmp1byte&BIT1) ?  eRfOn : eRfOff;
 
@@ -2996,7 +2999,7 @@ extern	void	dm_rf_pathcheck_workitemcallback(struct work_struct *work)
 
 	/* 2008/01/30 MH After discussing with SD3 Jerry, 0xc04/0xd04 register will
 	   always be the same. We only read 0xc04 now. */
-	rfpath = read_nic_byte(dev, 0xc04);
+	read_nic_byte(dev, 0xc04, &rfpath);
 
 	// Check Bit 0-3, it means if RF A-D is enabled.
 	for (i = 0; i < RF90_PATH_MAX; i++)
@@ -3052,12 +3055,13 @@ static void dm_rxpath_sel_byrssi(struct net_device *dev)
 
 	if(!cck_Rx_Path_initialized)
 	{
-		DM_RxPathSelTable.cck_Rx_path = (read_nic_byte(dev, 0xa07)&0xf);
+		read_nic_byte(dev, 0xa07, &DM_RxPathSelTable.cck_Rx_path);
+		DM_RxPathSelTable.cck_Rx_path &= 0xf;
 		cck_Rx_Path_initialized = 1;
 	}
 
-	DM_RxPathSelTable.disabledRF = 0xf;
-	DM_RxPathSelTable.disabledRF &= ~(read_nic_byte(dev, 0xc04));
+	read_nic_byte(dev, 0xc04, &DM_RxPathSelTable.disabledRF);
+	DM_RxPathSelTable.disabledRF = ~DM_RxPathSelTable.disabledRF & 0xf;
 
 	if(priv->ieee80211->mode == WIRELESS_MODE_B)
 	{
@@ -3731,17 +3735,17 @@ extern void dm_shadow_init(struct net_device *dev)
 	for (page = 0; page < 5; page++)
 		for (offset = 0; offset < 256; offset++)
 		{
-			dm_shadow[page][offset] = read_nic_byte(dev, offset+page*256);
+			read_nic_byte(dev, offset+page*256, &dm_shadow[page][offset]);
 			//DbgPrint("P-%d/O-%02x=%02x\r\n", page, offset, DM_Shadow[page][offset]);
 		}
 
 	for (page = 8; page < 11; page++)
 		for (offset = 0; offset < 256; offset++)
-			dm_shadow[page][offset] = read_nic_byte(dev, offset+page*256);
+			read_nic_byte(dev, offset+page*256, &dm_shadow[page][offset]);
 
 	for (page = 12; page < 15; page++)
 		for (offset = 0; offset < 256; offset++)
-			dm_shadow[page][offset] = read_nic_byte(dev, offset+page*256);
+			read_nic_byte(dev, offset+page*256, &dm_shadow[page][offset]);
 
 }   /* dm_shadow_init */
 
@@ -3858,14 +3862,14 @@ static void dm_check_txrateandretrycount(struct net_device *dev)
 	struct ieee80211_device *ieee = priv->ieee80211;
 	//for 11n tx rate
 //	priv->stats.CurrentShowTxate = read_nic_byte(dev, Current_Tx_Rate_Reg);
-	ieee->softmac_stats.CurrentShowTxate = read_nic_byte(dev, Current_Tx_Rate_Reg);
+	read_nic_byte(dev, Current_Tx_Rate_Reg, &ieee->softmac_stats.CurrentShowTxate);
 	//printk("=============>tx_rate_reg:%x\n", ieee->softmac_stats.CurrentShowTxate);
 	//for initial tx rate
 //	priv->stats.last_packet_rate = read_nic_byte(dev, Initial_Tx_Rate_Reg);
-	ieee->softmac_stats.last_packet_rate = read_nic_byte(dev ,Initial_Tx_Rate_Reg);
+	read_nic_byte(dev, Initial_Tx_Rate_Reg, &ieee->softmac_stats.last_packet_rate);
 	//for tx tx retry count
 //	priv->stats.txretrycount = read_nic_dword(dev, Tx_Retry_Count_Reg);
-	ieee->softmac_stats.txretrycount = read_nic_dword(dev, Tx_Retry_Count_Reg);
+	read_nic_dword(dev, Tx_Retry_Count_Reg, &ieee->softmac_stats.txretrycount);
 }
 
 static void dm_send_rssi_tofw(struct net_device *dev)

drivers/staging/rtl8192u/r8192U_hw.h

@@ -388,10 +388,11 @@ enum _RTL8192Usb_HW {
 #define EPROM_CMD_NORMAL 0
 #define EPROM_CMD_LOAD 1
 #define EPROM_CMD_PROGRAM 2
-#define EPROM_CS_SHIFT 3
-#define EPROM_CK_SHIFT 2
-#define EPROM_W_SHIFT 1
-#define EPROM_R_SHIFT 0
+#define EPROM_CS_BIT BIT(3)
+#define EPROM_CK_BIT BIT(2)
+#define EPROM_W_BIT  BIT(1)
+#define EPROM_R_BIT  BIT(0)
+
 	MAC0			= 0x000,
 	MAC1			= 0x001,
 	MAC2			= 0x002,

drivers/staging/rtl8192u/r8192U_wx.c

@@ -235,7 +235,7 @@ static int r8192_wx_read_nicb(struct net_device *dev,
 	down(&priv->wx_sem);
 
 	get_user(addr,(u32 *)wrqu->data.pointer);
-	data1 = read_nic_byte(dev, addr);
+	read_nic_byte(dev, addr, &data1);
 	wrqu->data.length = data1;
 
 	up(&priv->wx_sem);

drivers/staging/rtl8192u/r819xU_firmware.c

@@ -168,7 +168,7 @@ bool CPUcheck_maincodeok_turnonCPU(struct net_device *dev)
 
 	/* Check whether put code OK */
 	do {
-		CPU_status = read_nic_dword(dev, CPU_GEN);
+		read_nic_dword(dev, CPU_GEN, &CPU_status);
 
 		if (CPU_status&CPU_GEN_PUT_CODE_OK)
 			break;
@@ -183,13 +183,13 @@ bool CPUcheck_maincodeok_turnonCPU(struct net_device *dev)
 	}
 
 	/* Turn On CPU */
-	CPU_status = read_nic_dword(dev, CPU_GEN);
+	read_nic_dword(dev, CPU_GEN, &CPU_status);
 	write_nic_byte(dev, CPU_GEN, (u8)((CPU_status|CPU_GEN_PWR_STB_CPU)&0xff));
 	mdelay(1000);
 
 	/* Check whether CPU boot OK */
 	do {
-		CPU_status = read_nic_dword(dev, CPU_GEN);
+		read_nic_dword(dev, CPU_GEN, &CPU_status);
 
 		if (CPU_status&CPU_GEN_BOOT_RDY)
 			break;
@@ -218,7 +218,7 @@ bool CPUcheck_firmware_ready(struct net_device *dev)
 
 	/* Check Firmware Ready */
 	do {
-		CPU_status = read_nic_dword(dev, CPU_GEN);
+		read_nic_dword(dev, CPU_GEN, &CPU_status);
 
 		if (CPU_status&CPU_GEN_FIRM_RDY)
 			break;

drivers/staging/rtl8192u/r819xU_phy.c

@@ -90,7 +90,7 @@ void rtl8192_setBBreg(struct net_device *dev, u32 dwRegAddr, u32 dwBitMask, u32
 
 	if(dwBitMask!= bMaskDWord)
 	{//if not "double word" write
-		OriginalValue = read_nic_dword(dev, dwRegAddr);
+		read_nic_dword(dev, dwRegAddr, &OriginalValue);
 		BitShift = rtl8192_CalculateBitShift(dwBitMask);
 		NewValue = (((OriginalValue) & (~dwBitMask)) | (dwData << BitShift));
 		write_nic_dword(dev, dwRegAddr, NewValue);
@@ -111,7 +111,7 @@ u32 rtl8192_QueryBBReg(struct net_device *dev, u32 dwRegAddr, u32 dwBitMask)
 {
 	u32 Ret = 0, OriginalValue, BitShift;
 
-	OriginalValue = read_nic_dword(dev, dwRegAddr);
+	read_nic_dword(dev, dwRegAddr, &OriginalValue);
 	BitShift = rtl8192_CalculateBitShift(dwBitMask);
 	Ret =(OriginalValue & dwBitMask) >> BitShift;
 
@@ -379,6 +379,7 @@ phy_FwRFSerialRead(
 	u32		retValue = 0;
 	u32		Data = 0;
 	u8		time = 0;
+	u32		tmp;
 	//DbgPrint("FW RF CTRL\n\r");
 	/* 2007/11/02 MH Firmware RF Write control. By Francis' suggestion, we can
 	   not execute the scheme in the initial step. Otherwise, RF-R/W will waste
@@ -394,13 +395,15 @@ phy_FwRFSerialRead(
 	// 5. Trigger Fw to operate the command. bit 31
 	Data |= 0x80000000;
 	// 6. We can not execute read operation if bit 31 is 1.
-	while (read_nic_dword(dev, QPNR)&0x80000000)
+	read_nic_dword(dev, QPNR, &tmp);
+	while (tmp & 0x80000000)
 	{
 		// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
 		if (time++ < 100)
 		{
 			//DbgPrint("FW not finish RF-R Time=%d\n\r", time);
 			udelay(10);
+			read_nic_dword(dev, QPNR, &tmp);
 		}
 		else
 			break;
@@ -408,18 +411,20 @@ phy_FwRFSerialRead(
 	// 7. Execute read operation.
 	write_nic_dword(dev, QPNR, Data);
 	// 8. Check if firmawre send back RF content.
-	while (read_nic_dword(dev, QPNR)&0x80000000)
+	read_nic_dword(dev, QPNR, &tmp);
+	while (tmp & 0x80000000)
 	{
 		// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
 		if (time++ < 100)
 		{
 			//DbgPrint("FW not finish RF-W Time=%d\n\r", time);
 			udelay(10);
+			read_nic_dword(dev, QPNR, &tmp);
 		}
 		else
 			return	(0);
 	}
-	retValue = read_nic_dword(dev, RF_DATA);
+	read_nic_dword(dev, RF_DATA, &retValue);
 
 	return	(retValue);
 
@@ -440,6 +445,7 @@ phy_FwRFSerialWrite(
 		u32				Data	)
 {
 	u8	time = 0;
+	u32	tmp;
 
 	//DbgPrint("N FW RF CTRL RF-%d OF%02x DATA=%03x\n\r", eRFPath, Offset, Data);
 	/* 2007/11/02 MH Firmware RF Write control. By Francis' suggestion, we can
@@ -458,13 +464,15 @@ phy_FwRFSerialWrite(
 	Data |= 0x80000000;
 
 	// 6. Write operation. We can not write if bit 31 is 1.
-	while (read_nic_dword(dev, QPNR)&0x80000000)
+	read_nic_dword(dev, QPNR, &tmp);
+	while (tmp & 0x80000000)
 	{
 		// If FW can not finish RF-R/W for more than ?? times. We must reset FW.
 		if (time++ < 100)
 		{
 			//DbgPrint("FW not finish RF-W Time=%d\n\r", time);
 			udelay(10);
+			read_nic_dword(dev, QPNR, &tmp);
 		}
 		else
 			break;
@@ -719,7 +727,7 @@ u8 rtl8192_phy_checkBBAndRF(struct net_device *dev, HW90_BLOCK_E CheckBlock, RF9
 		case HW90_BLOCK_PHY0:
 		case HW90_BLOCK_PHY1:
 			write_nic_dword(dev, WriteAddr[CheckBlock], WriteData[i]);
-			dwRegRead = read_nic_dword(dev, WriteAddr[CheckBlock]);
+			read_nic_dword(dev, WriteAddr[CheckBlock], &dwRegRead);
 			break;
 
 		case HW90_BLOCK_RF:
@@ -770,11 +778,11 @@ void rtl8192_BB_Config_ParaFile(struct net_device *dev)
 	**************************************/
 
 	/*--set BB Global Reset--*/
-	bRegValue = read_nic_byte(dev, BB_GLOBAL_RESET);
+	read_nic_byte(dev, BB_GLOBAL_RESET, &bRegValue);
 	write_nic_byte(dev, BB_GLOBAL_RESET,(bRegValue|BB_GLOBAL_RESET_BIT));
 	mdelay(50);
 	/*---set BB reset Active---*/
-	dwRegValue = read_nic_dword(dev, CPU_GEN);
+	read_nic_dword(dev, CPU_GEN, &dwRegValue);
 	write_nic_dword(dev, CPU_GEN, (dwRegValue&(~CPU_GEN_BB_RST)));
 
 	/*----Ckeck FPGAPHY0 and PHY1 board is OK----*/
@@ -795,7 +803,7 @@ void rtl8192_BB_Config_ParaFile(struct net_device *dev)
 	rtl8192_phyConfigBB(dev, BaseBand_Config_PHY_REG);
 
 	/*----Set BB reset de-Active----*/
-	dwRegValue = read_nic_dword(dev, CPU_GEN);
+	read_nic_dword(dev, CPU_GEN, &dwRegValue);
 	write_nic_dword(dev, CPU_GEN, (dwRegValue|CPU_GEN_BB_RST));
 
 	/*----BB AGC table Initialization----*/
@@ -846,36 +854,32 @@ void rtl8192_BBConfig(struct net_device *dev)
 void rtl8192_phy_getTxPower(struct net_device *dev)
 {
 	struct r8192_priv *priv = ieee80211_priv(dev);
-	priv->MCSTxPowerLevelOriginalOffset[0] =
-		read_nic_dword(dev, rTxAGC_Rate18_06);
-	priv->MCSTxPowerLevelOriginalOffset[1] =
-		read_nic_dword(dev, rTxAGC_Rate54_24);
-	priv->MCSTxPowerLevelOriginalOffset[2] =
-		read_nic_dword(dev, rTxAGC_Mcs03_Mcs00);
-	priv->MCSTxPowerLevelOriginalOffset[3] =
-		read_nic_dword(dev, rTxAGC_Mcs07_Mcs04);
-	priv->MCSTxPowerLevelOriginalOffset[4] =
-		read_nic_dword(dev, rTxAGC_Mcs11_Mcs08);
-	priv->MCSTxPowerLevelOriginalOffset[5] =
-		read_nic_dword(dev, rTxAGC_Mcs15_Mcs12);
+	u8 tmp;
+	read_nic_dword(dev, rTxAGC_Rate18_06, &priv->MCSTxPowerLevelOriginalOffset[0]);
+	read_nic_dword(dev, rTxAGC_Rate54_24, &priv->MCSTxPowerLevelOriginalOffset[1]);
+	read_nic_dword(dev, rTxAGC_Mcs03_Mcs00, &priv->MCSTxPowerLevelOriginalOffset[2]);
+	read_nic_dword(dev, rTxAGC_Mcs07_Mcs04, &priv->MCSTxPowerLevelOriginalOffset[3]);
+	read_nic_dword(dev, rTxAGC_Mcs11_Mcs08, &priv->MCSTxPowerLevelOriginalOffset[4]);
+	read_nic_dword(dev, rTxAGC_Mcs15_Mcs12, &priv->MCSTxPowerLevelOriginalOffset[5]);
 
 	// read rx initial gain
-	priv->DefaultInitialGain[0] = read_nic_byte(dev, rOFDM0_XAAGCCore1);
-	priv->DefaultInitialGain[1] = read_nic_byte(dev, rOFDM0_XBAGCCore1);
-	priv->DefaultInitialGain[2] = read_nic_byte(dev, rOFDM0_XCAGCCore1);
-	priv->DefaultInitialGain[3] = read_nic_byte(dev, rOFDM0_XDAGCCore1);
+	read_nic_byte(dev, rOFDM0_XAAGCCore1, &priv->DefaultInitialGain[0]);
+	read_nic_byte(dev, rOFDM0_XBAGCCore1, &priv->DefaultInitialGain[1]);
+	read_nic_byte(dev, rOFDM0_XCAGCCore1, &priv->DefaultInitialGain[2]);
+	read_nic_byte(dev, rOFDM0_XDAGCCore1, &priv->DefaultInitialGain[3]);
 	RT_TRACE(COMP_INIT, "Default initial gain (c50=0x%x, c58=0x%x, c60=0x%x, c68=0x%x) \n",
 		priv->DefaultInitialGain[0], priv->DefaultInitialGain[1],
 		priv->DefaultInitialGain[2], priv->DefaultInitialGain[3]);
 
 	// read framesync
-	priv->framesync = read_nic_byte(dev, rOFDM0_RxDetector3);
-	priv->framesyncC34 = read_nic_byte(dev, rOFDM0_RxDetector2);
+	read_nic_byte(dev, rOFDM0_RxDetector3, &priv->framesync);
+	read_nic_byte(dev, rOFDM0_RxDetector2, &tmp);
+	priv->framesyncC34 = tmp;
 	RT_TRACE(COMP_INIT, "Default framesync (0x%x) = 0x%x \n",
 		rOFDM0_RxDetector3, priv->framesync);
 
 	// read SIFS (save the value read fome MACPHY_REG.txt)
-	priv->SifsTime = read_nic_word(dev, SIFS);
+	read_nic_word(dev, SIFS, &priv->SifsTime);
 
 	return;
 }
@@ -1525,7 +1529,7 @@ void rtl8192_SetBWModeWorkItem(struct net_device *dev)
 	}
 
 	//<1>Set MAC register
-	regBwOpMode = read_nic_byte(dev, BW_OPMODE);
+	read_nic_byte(dev, BW_OPMODE, &regBwOpMode);
 
 	switch (priv->CurrentChannelBW)
 	{