microblaze: Prefer to use pr_XXX instead of printk(KERN_XX)

Fix reset.c, timer.c, setup.c file.

Signed-off-by: Michal Simek <monstr@monstr.eu>

arch/microblaze/kernel/reset.c

@@ -26,14 +26,14 @@ void of_platform_reset_gpio_probe(void)
 				   "hard-reset-gpios", 0);
 
 	if (!gpio_is_valid(handle)) {
-		printk(KERN_INFO "Skipping unavailable RESET gpio %d (%s)\n",
+		pr_info("Skipping unavailable RESET gpio %d (%s)\n",
 				handle, "reset");
 		return;
 	}
 
 	ret = gpio_request(handle, "reset");
 	if (ret < 0) {
-		printk(KERN_INFO "GPIO pin is already allocated\n");
+		pr_info("GPIO pin is already allocated\n");
 		return;
 	}
 
@@ -50,7 +50,7 @@ void of_platform_reset_gpio_probe(void)
 	/* Setup output direction */
 	gpio_set_value(handle, 0);
 
-	printk(KERN_INFO "RESET: Registered gpio device: %d, current val: %d\n",
+	pr_info("RESET: Registered gpio device: %d, current val: %d\n",
 							handle, reset_val);
 	return;
 err:
@@ -76,7 +76,7 @@ void of_platform_reset_gpio_probe(void)
 
 void machine_restart(char *cmd)
 {
-	printk(KERN_NOTICE "Machine restart...\n");
+	pr_notice("Machine restart...\n");
 	gpio_system_reset();
 	while (1)
 		;
@@ -84,21 +84,21 @@ void machine_restart(char *cmd)
 
 void machine_shutdown(void)
 {
-	printk(KERN_NOTICE "Machine shutdown...\n");
+	pr_notice("Machine shutdown...\n");
 	while (1)
 		;
 }
 
 void machine_halt(void)
 {
-	printk(KERN_NOTICE "Machine halt...\n");
+	pr_notice("Machine halt...\n");
 	while (1)
 		;
 }
 
 void machine_power_off(void)
 {
-	printk(KERN_NOTICE "Machine power off...\n");
+	pr_notice("Machine power off...\n");
 	while (1)
 		;
 }

arch/microblaze/kernel/setup.c

@@ -69,7 +69,7 @@ void __init setup_arch(char **cmdline_p)
 	xilinx_pci_init();
 
 #if defined(CONFIG_SELFMOD_INTC) || defined(CONFIG_SELFMOD_TIMER)
-	printk(KERN_NOTICE "Self modified code enable\n");
+	pr_notice("Self modified code enable\n");
 #endif
 
 #ifdef CONFIG_VT

arch/microblaze/kernel/timer.c

@@ -116,21 +116,21 @@ static void microblaze_timer_set_mode(enum clock_event_mode mode,
 {
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
-		printk(KERN_INFO "%s: periodic\n", __func__);
+		pr_info("%s: periodic\n", __func__);
 		microblaze_timer0_start_periodic(freq_div_hz);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
-		printk(KERN_INFO "%s: oneshot\n", __func__);
+		pr_info("%s: oneshot\n", __func__);
 		break;
 	case CLOCK_EVT_MODE_UNUSED:
-		printk(KERN_INFO "%s: unused\n", __func__);
+		pr_info("%s: unused\n", __func__);
 		break;
 	case CLOCK_EVT_MODE_SHUTDOWN:
-		printk(KERN_INFO "%s: shutdown\n", __func__);
+		pr_info("%s: shutdown\n", __func__);
 		microblaze_timer0_stop();
 		break;
 	case CLOCK_EVT_MODE_RESUME:
-		printk(KERN_INFO "%s: resume\n", __func__);
+		pr_info("%s: resume\n", __func__);
 		break;
 	}
 }
@@ -274,14 +274,14 @@ void __init time_init(void)
 	timer_num = be32_to_cpup(of_get_property(timer,
 						"xlnx,one-timer-only", NULL));
 	if (timer_num) {
-		printk(KERN_EMERG "Please enable two timers in HW\n");
+		pr_emerg("Please   enable two timers in HW\n");
 		BUG();
 	}
 
 #ifdef CONFIG_SELFMOD_TIMER
 	selfmod_function((int *) arr_func, timer_baseaddr);
 #endif
-	printk(KERN_INFO "%s #0 at 0x%08x, irq=%d\n",
+	pr_info("%s #0 at 0x%08x, irq=%d\n",
 		timer->name, timer_baseaddr, irq);
 
 	/* If there is clock-frequency property than use it */