i2c: at91: remove old polling driver

It will get replaced by a superior one. Safe to remove since this one
depends on BROKEN anyhow.

Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>

[wsa: added commit message]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

arch/arm/mach-at91/include/mach/at91_twi.h

@@ -1,68 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91_twi.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * Two-wire Interface (TWI) registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_TWI_H
-#define AT91_TWI_H
-
-#define	AT91_TWI_CR		0x00		/* Control Register */
-#define		AT91_TWI_START		(1 <<  0)	/* Send a Start Condition */
-#define		AT91_TWI_STOP		(1 <<  1)	/* Send a Stop Condition */
-#define		AT91_TWI_MSEN		(1 <<  2)	/* Master Transfer Enable */
-#define		AT91_TWI_MSDIS		(1 <<  3)	/* Master Transfer Disable */
-#define		AT91_TWI_SVEN		(1 <<  4)	/* Slave Transfer Enable [SAM9260 only] */
-#define		AT91_TWI_SVDIS		(1 <<  5)	/* Slave Transfer Disable [SAM9260 only] */
-#define		AT91_TWI_SWRST		(1 <<  7)	/* Software Reset */
-
-#define	AT91_TWI_MMR		0x04		/* Master Mode Register */
-#define		AT91_TWI_IADRSZ		(3    <<  8)	/* Internal Device Address Size */
-#define			AT91_TWI_IADRSZ_NO		(0 << 8)
-#define			AT91_TWI_IADRSZ_1		(1 << 8)
-#define			AT91_TWI_IADRSZ_2		(2 << 8)
-#define			AT91_TWI_IADRSZ_3		(3 << 8)
-#define		AT91_TWI_MREAD		(1    << 12)	/* Master Read Direction */
-#define		AT91_TWI_DADR		(0x7f << 16)	/* Device Address */
-
-#define	AT91_TWI_SMR		0x08		/* Slave Mode Register [SAM9260 only] */
-#define		AT91_TWI_SADR		(0x7f << 16)	/* Slave Address */
-
-#define	AT91_TWI_IADR		0x0c		/* Internal Address Register */
-
-#define	AT91_TWI_CWGR		0x10		/* Clock Waveform Generator Register */
-#define		AT91_TWI_CLDIV		(0xff <<  0)	/* Clock Low Divisor */
-#define		AT91_TWI_CHDIV		(0xff <<  8)	/* Clock High Divisor */
-#define		AT91_TWI_CKDIV		(7    << 16)	/* Clock Divider */
-
-#define	AT91_TWI_SR		0x20		/* Status Register */
-#define		AT91_TWI_TXCOMP		(1 <<  0)	/* Transmission Complete */
-#define		AT91_TWI_RXRDY		(1 <<  1)	/* Receive Holding Register Ready */
-#define		AT91_TWI_TXRDY		(1 <<  2)	/* Transmit Holding Register Ready */
-#define		AT91_TWI_SVREAD		(1 <<  3)	/* Slave Read [SAM9260 only] */
-#define		AT91_TWI_SVACC		(1 <<  4)	/* Slave Access [SAM9260 only] */
-#define		AT91_TWI_GACC		(1 <<  5)	/* General Call Access [SAM9260 only] */
-#define		AT91_TWI_OVRE		(1 <<  6)	/* Overrun Error [AT91RM9200 only] */
-#define		AT91_TWI_UNRE		(1 <<  7)	/* Underrun Error [AT91RM9200 only] */
-#define		AT91_TWI_NACK		(1 <<  8)	/* Not Acknowledged */
-#define		AT91_TWI_ARBLST		(1 <<  9)	/* Arbitration Lost [SAM9260 only] */
-#define		AT91_TWI_SCLWS		(1 << 10)	/* Clock Wait State [SAM9260 only] */
-#define		AT91_TWI_EOSACC		(1 << 11)	/* End of Slave Address [SAM9260 only] */
-
-#define	AT91_TWI_IER		0x24		/* Interrupt Enable Register */
-#define	AT91_TWI_IDR		0x28		/* Interrupt Disable Register */
-#define	AT91_TWI_IMR		0x2c		/* Interrupt Mask Register */
-#define	AT91_TWI_RHR		0x30		/* Receive Holding Register */
-#define	AT91_TWI_THR		0x34		/* Transmit Holding Register */
-
-#endif
-

drivers/i2c/busses/Makefile

@@ -28,7 +28,6 @@ obj-$(CONFIG_I2C_HYDRA)		+= i2c-hydra.o
 obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 
 # Embedded system I2C/SMBus host controller drivers
-obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o

drivers/i2c/busses/i2c-at91.c

@@ -1,315 +0,0 @@
-/*
-    i2c Support for Atmel's AT91 Two-Wire Interface (TWI)
-
-    Copyright (C) 2004 Rick Bronson
-    Converted to 2.6 by Andrew Victor <andrew@sanpeople.com>
-
-    Borrowed heavily from original work by:
-    Copyright (C) 2000 Philip Edelbrock <phil@stimpy.netroedge.com>
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-*/
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/types.h>
-#include <linux/delay.h>
-#include <linux/i2c.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <mach/at91_twi.h>
-#include <mach/board.h>
-#include <mach/cpu.h>
-
-#define TWI_CLOCK		100000		/* Hz. max 400 Kbits/sec */
-
-
-static struct clk *twi_clk;
-static void __iomem *twi_base;
-
-#define at91_twi_read(reg)		__raw_readl(twi_base + (reg))
-#define at91_twi_write(reg, val)	__raw_writel((val), twi_base + (reg))
-
-
-/*
- * Initialize the TWI hardware registers.
- */
-static void __devinit at91_twi_hwinit(void)
-{
-	unsigned long cdiv, ckdiv;
-
-	at91_twi_write(AT91_TWI_IDR, 0xffffffff);	/* Disable all interrupts */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_SWRST);	/* Reset peripheral */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_MSEN);	/* Set Master mode */
-
-	/* Calcuate clock dividers */
-	cdiv = (clk_get_rate(twi_clk) / (2 * TWI_CLOCK)) - 3;
-	cdiv = cdiv + 1;	/* round up */
-	ckdiv = 0;
-	while (cdiv > 255) {
-		ckdiv++;
-		cdiv = cdiv >> 1;
-	}
-
-	if (cpu_is_at91rm9200()) {			/* AT91RM9200 Errata #22 */
-		if (ckdiv > 5) {
-			printk(KERN_ERR "AT91 I2C: Invalid TWI_CLOCK value!\n");
-			ckdiv = 5;
-		}
-	}
-
-	at91_twi_write(AT91_TWI_CWGR, (ckdiv << 16) | (cdiv << 8) | cdiv);
-}
-
-/*
- * Poll the i2c status register until the specified bit is set.
- * Returns 0 if timed out (100 msec).
- */
-static short at91_poll_status(unsigned long bit)
-{
-	int loop_cntr = 10000;
-
-	do {
-		udelay(10);
-	} while (!(at91_twi_read(AT91_TWI_SR) & bit) && (--loop_cntr > 0));
-
-	return (loop_cntr > 0);
-}
-
-static int xfer_read(struct i2c_adapter *adap, unsigned char *buf, int length)
-{
-	/* Send Start */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_START);
-
-	/* Read data */
-	while (length--) {
-		if (!length)	/* need to send Stop before reading last byte */
-			at91_twi_write(AT91_TWI_CR, AT91_TWI_STOP);
-		if (!at91_poll_status(AT91_TWI_RXRDY)) {
-			dev_dbg(&adap->dev, "RXRDY timeout\n");
-			return -ETIMEDOUT;
-		}
-		*buf++ = (at91_twi_read(AT91_TWI_RHR) & 0xff);
-	}
-
-	return 0;
-}
-
-static int xfer_write(struct i2c_adapter *adap, unsigned char *buf, int length)
-{
-	/* Load first byte into transmitter */
-	at91_twi_write(AT91_TWI_THR, *buf++);
-
-	/* Send Start */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_START);
-
-	do {
-		if (!at91_poll_status(AT91_TWI_TXRDY)) {
-			dev_dbg(&adap->dev, "TXRDY timeout\n");
-			return -ETIMEDOUT;
-		}
-
-		length--;	/* byte was transmitted */
-
-		if (length > 0)		/* more data to send? */
-			at91_twi_write(AT91_TWI_THR, *buf++);
-	} while (length);
-
-	/* Send Stop */
-	at91_twi_write(AT91_TWI_CR, AT91_TWI_STOP);
-
-	return 0;
-}
-
-/*
- * Generic i2c master transfer entrypoint.
- *
- * Note: We do not use Atmel's feature of storing the "internal device address".
- * Instead the "internal device address" has to be written using a separate
- * i2c message.
- * http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2004-September/024411.html
- */
-static int at91_xfer(struct i2c_adapter *adap, struct i2c_msg *pmsg, int num)
-{
-	int i, ret;
-
-	dev_dbg(&adap->dev, "at91_xfer: processing %d messages:\n", num);
-
-	for (i = 0; i < num; i++) {
-		dev_dbg(&adap->dev, " #%d: %sing %d byte%s %s 0x%02x\n", i,
-			pmsg->flags & I2C_M_RD ? "read" : "writ",
-			pmsg->len, pmsg->len > 1 ? "s" : "",
-			pmsg->flags & I2C_M_RD ? "from" : "to",	pmsg->addr);
-
-		at91_twi_write(AT91_TWI_MMR, (pmsg->addr << 16)
-			| ((pmsg->flags & I2C_M_RD) ? AT91_TWI_MREAD : 0));
-
-		if (pmsg->len && pmsg->buf) {	/* sanity check */
-			if (pmsg->flags & I2C_M_RD)
-				ret = xfer_read(adap, pmsg->buf, pmsg->len);
-			else
-				ret = xfer_write(adap, pmsg->buf, pmsg->len);
-
-			if (ret)
-				return ret;
-
-			/* Wait until transfer is finished */
-			if (!at91_poll_status(AT91_TWI_TXCOMP)) {
-				dev_dbg(&adap->dev, "TXCOMP timeout\n");
-				return -ETIMEDOUT;
-			}
-		}
-		dev_dbg(&adap->dev, "transfer complete\n");
-		pmsg++;		/* next message */
-	}
-	return i;
-}
-
-/*
- * Return list of supported functionality.
- */
-static u32 at91_func(struct i2c_adapter *adapter)
-{
-	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
-}
-
-static struct i2c_algorithm at91_algorithm = {
-	.master_xfer	= at91_xfer,
-	.functionality	= at91_func,
-};
-
-/*
- * Main initialization routine.
- */
-static int __devinit at91_i2c_probe(struct platform_device *pdev)
-{
-	struct i2c_adapter *adapter;
-	struct resource *res;
-	int rc;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res)
-		return -ENXIO;
-
-	if (!request_mem_region(res->start, resource_size(res), "at91_i2c"))
-		return -EBUSY;
-
-	twi_base = ioremap(res->start, resource_size(res));
-	if (!twi_base) {
-		rc = -ENOMEM;
-		goto fail0;
-	}
-
-	twi_clk = clk_get(NULL, "twi_clk");
-	if (IS_ERR(twi_clk)) {
-		dev_err(&pdev->dev, "no clock defined\n");
-		rc = -ENODEV;
-		goto fail1;
-	}
-
-	adapter = kzalloc(sizeof(struct i2c_adapter), GFP_KERNEL);
-	if (adapter == NULL) {
-		dev_err(&pdev->dev, "can't allocate inteface!\n");
-		rc = -ENOMEM;
-		goto fail2;
-	}
-	snprintf(adapter->name, sizeof(adapter->name), "AT91");
-	adapter->algo = &at91_algorithm;
-	adapter->class = I2C_CLASS_HWMON;
-	adapter->dev.parent = &pdev->dev;
-	/* adapter->id == 0 ... only one TWI controller for now */
-
-	platform_set_drvdata(pdev, adapter);
-
-	clk_enable(twi_clk);		/* enable peripheral clock */
-	at91_twi_hwinit();		/* initialize TWI controller */
-
-	rc = i2c_add_numbered_adapter(adapter);
-	if (rc) {
-		dev_err(&pdev->dev, "Adapter %s registration failed\n",
-				adapter->name);
-		goto fail3;
-	}
-
-	dev_info(&pdev->dev, "AT91 i2c bus driver.\n");
-	return 0;
-
-fail3:
-	platform_set_drvdata(pdev, NULL);
-	kfree(adapter);
-	clk_disable(twi_clk);
-fail2:
-	clk_put(twi_clk);
-fail1:
-	iounmap(twi_base);
-fail0:
-	release_mem_region(res->start, resource_size(res));
-
-	return rc;
-}
-
-static int __devexit at91_i2c_remove(struct platform_device *pdev)
-{
-	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
-	struct resource *res;
-	int rc;
-
-	rc = i2c_del_adapter(adapter);
-	platform_set_drvdata(pdev, NULL);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	iounmap(twi_base);
-	release_mem_region(res->start, resource_size(res));
-
-	clk_disable(twi_clk);		/* disable peripheral clock */
-	clk_put(twi_clk);
-
-	return rc;
-}
-
-#ifdef CONFIG_PM
-
-/* NOTE: could save a few mA by keeping clock off outside of at91_xfer... */
-
-static int at91_i2c_suspend(struct device *dev)
-{
-	clk_disable(twi_clk);
-	return 0;
-}
-
-static int at91_i2c_resume(struct device *dev)
-{
-	return clk_enable(twi_clk);
-}
-
-static SIMPLE_DEV_PM_OPS(at91_i2c_pm, at91_i2c_suspend, at91_i2c_resume);
-#define AT91_I2C_PM	(&at91_i2c_pm)
-
-#else
-#define AT91_I2C_PM	NULL
-#endif
-
-static struct platform_driver at91_i2c_driver = {
-	.probe		= at91_i2c_probe,
-	.remove		= __devexit_p(at91_i2c_remove),
-	.driver		= {
-		.name	= "at91_i2c",
-		.owner	= THIS_MODULE,
-		.pm	= AT91_I2C_PM,
-	},
-};
-
-module_platform_driver(at91_i2c_driver);
-
-MODULE_AUTHOR("Rick Bronson");
-MODULE_DESCRIPTION("I2C (TWI) driver for Atmel AT91");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:at91_i2c");