leds: add driver for TCA6507 LED controller

TI's TCA6507 is the LED driver in the GTA04 Openmoko motherboard.  The
driver provides full support for brightness levels and hardware blinking.

This driver can drive each of 7 outputs as an LED or a GPIO output,
and provides hardware-assist blinking.

[akpm@linux-foundation.org: fix __mod_i2c_device_table alias]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/leds/Kconfig

@@ -388,6 +388,14 @@ config LEDS_RENESAS_TPU
 	  pin function. The latter to support brightness control.
 	  Brightness control is supported but hardware blinking is not.
 
+config LEDS_TCA6507
+	tristate "LED Support for TCA6507 I2C chip"
+	depends on LEDS_CLASS && I2C
+	help
+	  This option enables support for LEDs connected to TC6507
+	  LED driver chips accessed via the I2C bus.
+	  Driver support brightness control and hardware-assisted blinking.
+
 config LEDS_TRIGGERS
 	bool "LED Trigger support"
 	depends on LEDS_CLASS

drivers/leds/Makefile

@@ -25,6 +25,7 @@ obj-$(CONFIG_LEDS_GPIO)			+= leds-gpio.o
 obj-$(CONFIG_LEDS_LP3944)		+= leds-lp3944.o
 obj-$(CONFIG_LEDS_LP5521)		+= leds-lp5521.o
 obj-$(CONFIG_LEDS_LP5523)		+= leds-lp5523.o
+obj-$(CONFIG_LEDS_TCA6507)		+= leds-tca6507.o
 obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
 obj-$(CONFIG_LEDS_HP6XX)		+= leds-hp6xx.o
 obj-$(CONFIG_LEDS_FSG)			+= leds-fsg.o

drivers/leds/leds-tca6507.c

@@ -0,0 +1,779 @@
+/*
+ * leds-tca6507
+ *
+ * The TCA6507 is a programmable LED controller that can drive 7
+ * separate lines either by holding them low, or by pulsing them
+ * with modulated width.
+ * The modulation can be varied in a simple pattern to produce a blink or
+ * double-blink.
+ *
+ * This driver can configure each line either as a 'GPIO' which is out-only
+ * (no pull-up) or as an LED with variable brightness and hardware-assisted
+ * blinking.
+ *
+ * Apart from OFF and ON there are three programmable brightness levels which
+ * can be programmed from 0 to 15 and indicate how many 500usec intervals in
+ * each 8msec that the led is 'on'.  The levels are named MASTER, BANK0 and
+ * BANK1.
+ *
+ * There are two different blink rates that can be programmed, each with
+ * separate time for rise, on, fall, off and second-off.  Thus if 3 or more
+ * different non-trivial rates are required, software must be used for the extra
+ * rates. The two different blink rates must align with the two levels BANK0 and
+ * BANK1.
+ * This driver does not support double-blink so 'second-off' always matches
+ * 'off'.
+ *
+ * Only 16 different times can be programmed in a roughly logarithmic scale from
+ * 64ms to 16320ms.  To be precise the possible times are:
+ *    0, 64, 128, 192, 256, 384, 512, 768,
+ *    1024, 1536, 2048, 3072, 4096, 5760, 8128, 16320
+ *
+ * Times that cannot be closely matched with these must be
+ * handled in software.  This driver allows 12.5% error in matching.
+ *
+ * This driver does not allow rise/fall rates to be set explicitly.  When trying
+ * to match a given 'on' or 'off' period, an appropriate pair of 'change' and
+ * 'hold' times are chosen to get a close match.  If the target delay is even,
+ * the 'change' number will be the smaller; if odd, the 'hold' number will be
+ * the smaller.
+
+ * Choosing pairs of delays with 12.5% errors allows us to match delays in the
+ * ranges: 56-72, 112-144, 168-216, 224-27504, 28560-36720.
+ * 26% of the achievable sums can be matched by multiple pairings. For example
+ * 1536 == 1536+0, 1024+512, or 768+768.  This driver will always choose the
+ * pairing with the least maximum - 768+768 in this case.  Other pairings are
+ * not available.
+ *
+ * Access to the 3 levels and 2 blinks are on a first-come, first-served basis.
+ * Access can be shared by multiple leds if they have the same level and
+ * either same blink rates, or some don't blink.
+ * When a led changes, it relinquishes access and tries again, so it might
+ * lose access to hardware blink.
+ * If a blink engine cannot be allocated, software blink is used.
+ * If the desired brightness cannot be allocated, the closest available non-zero
+ * brightness is used.  As 'full' is always available, the worst case would be
+ * to have two different blink rates at '1', with Max at '2', then other leds
+ * will have to choose between '2' and '16'.  Hopefully this is not likely.
+ *
+ * Each bank (BANK0 and BANK1) has two usage counts - LEDs using the brightness
+ * and LEDs using the blink.  It can only be reprogrammed when the appropriate
+ * counter is zero.  The MASTER level has a single usage count.
+ *
+ * Each Led has programmable 'on' and 'off' time as milliseconds.  With each
+ * there is a flag saying if it was explicitly requested or defaulted.
+ * Similarly the banks know if each time was explicit or a default.  Defaults
+ * are permitted to be changed freely - they are not recognised when matching.
+ *
+ *
+ * An led-tca6507 device must be provided with platform data.  This data
+ * lists for each output: the name, default trigger, and whether the signal
+ * is being used as a GPiO rather than an led.  'struct led_plaform_data'
+ * is used for this.  If 'name' is NULL, the output isn't used.  If 'flags'
+ * is TCA6507_MAKE_CPIO, the output is a GPO.
+ * The "struct led_platform_data" can be embedded in a
+ * "struct tca6507_platform_data" which adds a 'gpio_base' for the GPiOs,
+ * and a 'setup' callback which is called once the GPiOs are available.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/workqueue.h>
+#include <linux/leds-tca6507.h>
+
+/* LED select registers determine the source that drives LED outputs */
+#define TCA6507_LS_LED_OFF	0x0	/* Output HI-Z (off) */
+#define TCA6507_LS_LED_OFF1	0x1	/* Output HI-Z (off) - not used */
+#define TCA6507_LS_LED_PWM0	0x2	/* Output LOW with Bank0 rate */
+#define TCA6507_LS_LED_PWM1	0x3	/* Output LOW with Bank1 rate */
+#define TCA6507_LS_LED_ON	0x4	/* Output LOW (on) */
+#define TCA6507_LS_LED_MIR	0x5	/* Output LOW with Master Intensity */
+#define TCA6507_LS_BLINK0	0x6	/* Blink at Bank0 rate */
+#define TCA6507_LS_BLINK1	0x7	/* Blink at Bank1 rate */
+
+enum {
+	BANK0,
+	BANK1,
+	MASTER,
+};
+static int bank_source[3] = {
+	TCA6507_LS_LED_PWM0,
+	TCA6507_LS_LED_PWM1,
+	TCA6507_LS_LED_MIR,
+};
+static int blink_source[2] = {
+	TCA6507_LS_BLINK0,
+	TCA6507_LS_BLINK1,
+};
+
+/* PWM registers */
+#define	TCA6507_REG_CNT			11
+
+/*
+ * 0x00, 0x01, 0x02 encode the TCA6507_LS_* values, each output
+ * owns one bit in each register
+ */
+#define	TCA6507_FADE_ON			0x03
+#define	TCA6507_FULL_ON			0x04
+#define	TCA6507_FADE_OFF		0x05
+#define	TCA6507_FIRST_OFF		0x06
+#define	TCA6507_SECOND_OFF		0x07
+#define	TCA6507_MAX_INTENSITY		0x08
+#define	TCA6507_MASTER_INTENSITY	0x09
+#define	TCA6507_INITIALIZE		0x0A
+
+#define	INIT_CODE			0x8
+
+#define TIMECODES 16
+static int time_codes[TIMECODES] = {
+	0, 64, 128, 192, 256, 384, 512, 768,
+	1024, 1536, 2048, 3072, 4096, 5760, 8128, 16320
+};
+
+/* Convert an led.brightness level (0..255) to a TCA6507 level (0..15) */
+static inline int TO_LEVEL(int brightness)
+{
+	return brightness >> 4;
+}
+
+/* ...and convert back */
+static inline int TO_BRIGHT(int level)
+{
+	if (level)
+		return (level << 4) | 0xf;
+	return 0;
+}
+
+#define NUM_LEDS 7
+struct tca6507_chip {
+	int			reg_set;	/* One bit per register where
+						 * a '1' means the register
+						 * should be written */
+	u8			reg_file[TCA6507_REG_CNT];
+	/* Bank 2 is Master Intensity and doesn't use times */
+	struct bank {
+		int level;
+		int ontime, offtime;
+		int on_dflt, off_dflt;
+		int time_use, level_use;
+	} bank[3];
+	struct i2c_client	*client;
+	struct work_struct	work;
+	spinlock_t		lock;
+
+	struct tca6507_led {
+		struct tca6507_chip	*chip;
+		struct led_classdev	led_cdev;
+		int			num;
+		int			ontime, offtime;
+		int			on_dflt, off_dflt;
+		int			bank;	/* Bank used, or -1 */
+		int			blink;	/* Set if hardware-blinking */
+	} leds[NUM_LEDS];
+#ifdef CONFIG_GPIOLIB
+	struct gpio_chip		gpio;
+	const char			*gpio_name[NUM_LEDS];
+	int				gpio_map[NUM_LEDS];
+#endif
+};
+
+static const struct i2c_device_id tca6507_id[] = {
+	{ "tca6507" },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, tca6507_id);
+
+static int choose_times(int msec, int *c1p, int *c2p)
+{
+	/*
+	 * Choose two timecodes which add to 'msec' as near as possible.
+	 * The first returned is the 'on' or 'off' time.  The second is to be
+	 * used as a 'fade-on' or 'fade-off' time.  If 'msec' is even,
+	 * the first will not be smaller than the second.  If 'msec' is odd,
+	 * the first will not be larger than the second.
+	 * If we cannot get a sum within 1/8 of 'msec' fail with -EINVAL,
+	 * otherwise return the sum that was achieved, plus 1 if the first is
+	 * smaller.
+	 * If two possibilities are equally good (e.g. 512+0, 256+256), choose
+	 * the first pair so there is more change-time visible (i.e. it is
+	 * softer).
+	 */
+	int c1, c2;
+	int tmax = msec * 9 / 8;
+	int tmin = msec * 7 / 8;
+	int diff = 65536;
+
+	/* We start at '1' to ensure we never even think of choosing a
+	 * total time of '0'.
+	 */
+	for (c1 = 1; c1 < TIMECODES; c1++) {
+		int t = time_codes[c1];
+		if (t*2 < tmin)
+			continue;
+		if (t > tmax)
+			break;
+		for (c2 = 0; c2 <= c1; c2++) {
+			int tt = t + time_codes[c2];
+			int d;
+			if (tt < tmin)
+				continue;
+			if (tt > tmax)
+				break;
+			/* This works! */
+			d = abs(msec - tt);
+			if (d >= diff)
+				continue;
+			/* Best yet */
+			*c1p = c1;
+			*c2p = c2;
+			diff = d;
+			if (d == 0)
+				return msec;
+		}
+	}
+	if (diff < 65536) {
+		int actual;
+		if (msec & 1) {
+			c1 = *c2p;
+			*c2p = *c1p;
+			*c1p = c1;
+		}
+		actual = time_codes[*c1p] + time_codes[*c2p];
+		if (*c1p < *c2p)
+			return actual + 1;
+		else
+			return actual;
+	}
+	/* No close match */
+	return -EINVAL;
+}
+
+/*
+ * Update the register file with the appropriate 3-bit state for
+ * the given led.
+ */
+static void set_select(struct tca6507_chip *tca, int led, int val)
+{
+	int mask = (1 << led);
+	int bit;
+
+	for (bit = 0; bit < 3; bit++) {
+		int n = tca->reg_file[bit] & ~mask;
+		if (val & (1 << bit))
+			n |= mask;
+		if (tca->reg_file[bit] != n) {
+			tca->reg_file[bit] = n;
+			tca->reg_set |= (1 << bit);
+		}
+	}
+}
+
+/* Update the register file with the appropriate 4-bit code for
+ * one bank or other.  This can be used for timers, for levels, or
+ * for initialisation.
+ */
+static void set_code(struct tca6507_chip *tca, int reg, int bank, int new)
+{
+	int mask = 0xF;
+	int n;
+	if (bank) {
+		mask <<= 4;
+		new <<= 4;
+	}
+	n = tca->reg_file[reg] & ~mask;
+	n |= new;
+	if (tca->reg_file[reg] != n) {
+		tca->reg_file[reg] = n;
+		tca->reg_set |= 1 << reg;
+	}
+}
+
+/* Update brightness level. */
+static void set_level(struct tca6507_chip *tca, int bank, int level)
+{
+	switch (bank) {
+	case BANK0:
+	case BANK1:
+		set_code(tca, TCA6507_MAX_INTENSITY, bank, level);
+		break;
+	case MASTER:
+		set_code(tca, TCA6507_MASTER_INTENSITY, 0, level);
+		break;
+	}
+	tca->bank[bank].level = level;
+}
+
+/* Record all relevant time code for a given bank */
+static void set_times(struct tca6507_chip *tca, int bank)
+{
+	int c1, c2;
+	int result;
+
+	result = choose_times(tca->bank[bank].ontime, &c1, &c2);
+	dev_dbg(&tca->client->dev,
+		"Chose on  times %d(%d) %d(%d) for %dms\n", c1, time_codes[c1],
+		c2, time_codes[c2], tca->bank[bank].ontime);
+	set_code(tca, TCA6507_FADE_ON, bank, c2);
+	set_code(tca, TCA6507_FULL_ON, bank, c1);
+	tca->bank[bank].ontime = result;
+
+	result = choose_times(tca->bank[bank].offtime, &c1, &c2);
+	dev_dbg(&tca->client->dev,
+		"Chose off times %d(%d) %d(%d) for %dms\n", c1, time_codes[c1],
+		c2, time_codes[c2], tca->bank[bank].offtime);
+	set_code(tca, TCA6507_FADE_OFF, bank, c2);
+	set_code(tca, TCA6507_FIRST_OFF, bank, c1);
+	set_code(tca, TCA6507_SECOND_OFF, bank, c1);
+	tca->bank[bank].offtime = result;
+
+	set_code(tca, TCA6507_INITIALIZE, bank, INIT_CODE);
+}
+
+/* Write all needed register of tca6507 */
+
+static void tca6507_work(struct work_struct *work)
+{
+	struct tca6507_chip *tca = container_of(work, struct tca6507_chip,
+						work);
+	struct i2c_client *cl = tca->client;
+	int set;
+	u8 file[TCA6507_REG_CNT];
+	int r;
+
+	spin_lock_irq(&tca->lock);
+	set = tca->reg_set;
+	memcpy(file, tca->reg_file, TCA6507_REG_CNT);
+	tca->reg_set = 0;
+	spin_unlock_irq(&tca->lock);
+
+	for (r = 0; r < TCA6507_REG_CNT; r++)
+		if (set & (1<<r))
+			i2c_smbus_write_byte_data(cl, r, file[r]);
+}
+
+static void led_release(struct tca6507_led *led)
+{
+	/* If led owns any resource, release it. */
+	struct tca6507_chip *tca = led->chip;
+	if (led->bank >= 0) {
+		struct bank *b = tca->bank + led->bank;
+		if (led->blink)
+			b->time_use--;
+		b->level_use--;
+	}
+	led->blink = 0;
+	led->bank = -1;
+}
+
+static int led_prepare(struct tca6507_led *led)
+{
+	/* Assign this led to a bank, configuring that bank if necessary. */
+	int level = TO_LEVEL(led->led_cdev.brightness);
+	struct tca6507_chip *tca = led->chip;
+	int c1, c2;
+	int i;
+	struct bank *b;
+	int need_init = 0;
+
+	led->led_cdev.brightness = TO_BRIGHT(level);
+	if (level == 0) {
+		set_select(tca, led->num, TCA6507_LS_LED_OFF);
+		return 0;
+	}
+
+	if (led->ontime == 0 || led->offtime == 0) {
+		/*
+		 * Just set the brightness, choosing first usable bank.
+		 * If none perfect, choose best.
+		 * Count backwards so we check MASTER bank first
+		 * to avoid wasting a timer.
+		 */
+		int best = -1;/* full-on */
+		int diff = 15-level;
+
+		if (level == 15) {
+			set_select(tca, led->num, TCA6507_LS_LED_ON);
+			return 0;
+		}
+
+		for (i = MASTER; i >= BANK0; i--) {
+			int d;
+			if (tca->bank[i].level == level ||
+			    tca->bank[i].level_use == 0) {
+				best = i;
+				break;
+			}
+			d = abs(level - tca->bank[i].level);
+			if (d < diff) {
+				diff = d;
+				best = i;
+			}
+		}
+		if (best == -1) {
+			/* Best brightness is full-on */
+			set_select(tca, led->num, TCA6507_LS_LED_ON);
+			led->led_cdev.brightness = LED_FULL;
+			return 0;
+		}
+
+		if (!tca->bank[best].level_use)
+			set_level(tca, best, level);
+
+		tca->bank[best].level_use++;
+		led->bank = best;
+		set_select(tca, led->num, bank_source[best]);
+		led->led_cdev.brightness = TO_BRIGHT(tca->bank[best].level);
+		return 0;
+	}
+
+	/*
+	 * We have on/off time so we need to try to allocate a timing bank.
+	 * First check if times are compatible with hardware and give up if
+	 * not.
+	 */
+	if (choose_times(led->ontime, &c1, &c2) < 0)
+		return -EINVAL;
+	if (choose_times(led->offtime, &c1, &c2) < 0)
+		return -EINVAL;
+
+	for (i = BANK0; i <= BANK1; i++) {
+		if (tca->bank[i].level_use == 0)
+			/* not in use - it is ours! */
+			break;
+		if (tca->bank[i].level != level)
+			/* Incompatible level - skip */
+			/* FIX: if timer matches we maybe should consider
+			 * this anyway...
+			 */
+			continue;
+
+		if (tca->bank[i].time_use == 0)
+			/* Timer not in use, and level matches - use it */
+			break;
+
+		if (!(tca->bank[i].on_dflt ||
+		      led->on_dflt ||
+		      tca->bank[i].ontime == led->ontime))
+			/* on time is incompatible */
+			continue;
+
+		if (!(tca->bank[i].off_dflt ||
+		      led->off_dflt ||
+		      tca->bank[i].offtime == led->offtime))
+			/* off time is incompatible */
+			continue;
+
+		/* looks like a suitable match */
+		break;
+	}
+
+	if (i > BANK1)
+		/* Nothing matches - how sad */
+		return -EINVAL;
+
+	b = &tca->bank[i];
+	if (b->level_use == 0)
+		set_level(tca, i, level);
+	b->level_use++;
+	led->bank = i;
+
+	if (b->on_dflt ||
+	    !led->on_dflt ||
+	    b->time_use == 0) {
+		b->ontime = led->ontime;
+		b->on_dflt = led->on_dflt;
+		need_init = 1;
+	}
+
+	if (b->off_dflt ||
+	    !led->off_dflt ||
+	    b->time_use == 0) {
+		b->offtime = led->offtime;
+		b->off_dflt = led->off_dflt;
+		need_init = 1;
+	}
+
+	if (need_init)
+		set_times(tca, i);
+
+	led->ontime = b->ontime;
+	led->offtime = b->offtime;
+
+	b->time_use++;
+	led->blink = 1;
+	led->led_cdev.brightness = TO_BRIGHT(b->level);
+	set_select(tca, led->num, blink_source[i]);
+	return 0;
+}
+
+static int led_assign(struct tca6507_led *led)
+{
+	struct tca6507_chip *tca = led->chip;
+	int err;
+	unsigned long flags;
+
+	spin_lock_irqsave(&tca->lock, flags);
+	led_release(led);
+	err = led_prepare(led);
+	if (err) {
+		/*
+		 * Can only fail on timer setup.  In that case we need to
+		 * re-establish as steady level.
+		 */
+		led->ontime = 0;
+		led->offtime = 0;
+		led_prepare(led);
+	}
+	spin_unlock_irqrestore(&tca->lock, flags);
+
+	if (tca->reg_set)
+		schedule_work(&tca->work);
+	return err;
+}
+
+static void tca6507_brightness_set(struct led_classdev *led_cdev,
+				   enum led_brightness brightness)
+{
+	struct tca6507_led *led = container_of(led_cdev, struct tca6507_led,
+					       led_cdev);
+	led->led_cdev.brightness = brightness;
+	led->ontime = 0;
+	led->offtime = 0;
+	led_assign(led);
+}
+
+static int tca6507_blink_set(struct led_classdev *led_cdev,
+			     unsigned long *delay_on,
+			     unsigned long *delay_off)
+{
+	struct tca6507_led *led = container_of(led_cdev, struct tca6507_led,
+					       led_cdev);
+
+	if (*delay_on == 0)
+		led->on_dflt = 1;
+	else if (delay_on != &led_cdev->blink_delay_on)
+		led->on_dflt = 0;
+	led->ontime = *delay_on;
+
+	if (*delay_off == 0)
+		led->off_dflt = 1;
+	else if (delay_off != &led_cdev->blink_delay_off)
+		led->off_dflt = 0;
+	led->offtime = *delay_off;
+
+	if (led->ontime == 0)
+		led->ontime = 512;
+	if (led->offtime == 0)
+		led->offtime = 512;
+
+	if (led->led_cdev.brightness == LED_OFF)
+		led->led_cdev.brightness = LED_FULL;
+	if (led_assign(led) < 0) {
+		led->ontime = 0;
+		led->offtime = 0;
+		led->led_cdev.brightness = LED_OFF;
+		return -EINVAL;
+	}
+	*delay_on = led->ontime;
+	*delay_off = led->offtime;
+	return 0;
+}
+
+#ifdef CONFIG_GPIOLIB
+static void tca6507_gpio_set_value(struct gpio_chip *gc,
+				   unsigned offset, int val)
+{
+	struct tca6507_chip *tca = container_of(gc, struct tca6507_chip, gpio);
+	unsigned long flags;
+
+	spin_lock_irqsave(&tca->lock, flags);
+	/*
+	 * 'OFF' is floating high, and 'ON' is pulled down, so it has the
+	 * inverse sense of 'val'.
+	 */
+	set_select(tca, tca->gpio_map[offset],
+		   val ? TCA6507_LS_LED_OFF : TCA6507_LS_LED_ON);
+	spin_unlock_irqrestore(&tca->lock, flags);
+	if (tca->reg_set)
+		schedule_work(&tca->work);
+}
+
+static int tca6507_gpio_direction_output(struct gpio_chip *gc,
+					  unsigned offset, int val)
+{
+	tca6507_gpio_set_value(gc, offset, val);
+	return 0;
+}
+
+static int tca6507_probe_gpios(struct i2c_client *client,
+			       struct tca6507_chip *tca,
+			       struct tca6507_platform_data *pdata)
+{
+	int err;
+	int i = 0;
+	int gpios = 0;
+
+	for (i = 0; i < NUM_LEDS; i++)
+		if (pdata->leds.leds[i].name && pdata->leds.leds[i].flags) {
+			/* Configure as a gpio */
+			tca->gpio_name[gpios] = pdata->leds.leds[i].name;
+			tca->gpio_map[gpios] = i;
+			gpios++;
+		}
+
+	if (!gpios)
+		return 0;
+
+	tca->gpio.label = "gpio-tca6507";
+	tca->gpio.names = tca->gpio_name;
+	tca->gpio.ngpio = gpios;
+	tca->gpio.base = pdata->gpio_base;
+	tca->gpio.owner = THIS_MODULE;
+	tca->gpio.direction_output = tca6507_gpio_direction_output;
+	tca->gpio.set = tca6507_gpio_set_value;
+	tca->gpio.dev = &client->dev;
+	err = gpiochip_add(&tca->gpio);
+	if (err) {
+		tca->gpio.ngpio = 0;
+		return err;
+	}
+	if (pdata->setup)
+		pdata->setup(tca->gpio.base, tca->gpio.ngpio);
+	return 0;
+}
+
+static void tca6507_remove_gpio(struct tca6507_chip *tca)
+{
+	if (tca->gpio.ngpio) {
+		int err = gpiochip_remove(&tca->gpio);
+		dev_err(&tca->client->dev, "%s failed, %d\n",
+			"gpiochip_remove()", err);
+	}
+}
+#else /* CONFIG_GPIOLIB */
+static int tca6507_probe_gpios(struct i2c_client *client,
+			       struct tca6507_chip *tca,
+			       struct tca6507_platform_data *pdata)
+{
+	return 0;
+}
+static void tca6507_remove_gpio(struct tca6507_chip *tca)
+{
+}
+#endif /* CONFIG_GPIOLIB */
+
+static int __devinit tca6507_probe(struct i2c_client *client,
+				   const struct i2c_device_id *id)
+{
+	struct tca6507_chip *tca;
+	struct i2c_adapter *adapter;
+	struct tca6507_platform_data *pdata;
+	int err;
+	int i = 0;
+
+	adapter = to_i2c_adapter(client->dev.parent);
+	pdata = client->dev.platform_data;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))
+		return -EIO;
+
+	if (!pdata || pdata->leds.num_leds != NUM_LEDS) {
+		dev_err(&client->dev, "Need %d entries in platform-data list\n",
+			NUM_LEDS);
+		return -ENODEV;
+	}
+	err = -ENOMEM;
+	tca = kzalloc(sizeof(*tca), GFP_KERNEL);
+	if (!tca)
+		goto exit;
+
+	tca->client = client;
+	INIT_WORK(&tca->work, tca6507_work);
+	spin_lock_init(&tca->lock);
+	i2c_set_clientdata(client, tca);
+
+	for (i = 0; i < NUM_LEDS; i++) {
+		struct tca6507_led *l = tca->leds + i;
+
+		l->chip = tca;
+		l->num = i;
+		if (pdata->leds.leds[i].name && !pdata->leds.leds[i].flags) {
+			l->led_cdev.name = pdata->leds.leds[i].name;
+			l->led_cdev.default_trigger
+				= pdata->leds.leds[i].default_trigger;
+			l->led_cdev.brightness_set = tca6507_brightness_set;
+			l->led_cdev.blink_set = tca6507_blink_set;
+			l->bank = -1;
+			err = led_classdev_register(&client->dev,
+						    &l->led_cdev);
+			if (err < 0)
+				goto exit;
+		}
+	}
+	err = tca6507_probe_gpios(client, tca, pdata);
+	if (err)
+		goto exit;
+	/* set all registers to known state - zero */
+	tca->reg_set = 0x7f;
+	schedule_work(&tca->work);
+
+	return 0;
+exit:
+	while (i--)
+		if (tca->leds[i].led_cdev.name)
+			led_classdev_unregister(&tca->leds[i].led_cdev);
+	cancel_work_sync(&tca->work);
+	i2c_set_clientdata(client, NULL);
+	kfree(tca);
+	return err;
+}
+
+static int __devexit tca6507_remove(struct i2c_client *client)
+{
+	int i;
+	struct tca6507_chip *tca = i2c_get_clientdata(client);
+	struct tca6507_led *tca_leds = tca->leds;
+
+	for (i = 0; i < NUM_LEDS; i++) {
+		if (tca_leds[i].led_cdev.name)
+			led_classdev_unregister(&tca_leds[i].led_cdev);
+	}
+	tca6507_remove_gpio(tca);
+	cancel_work_sync(&tca->work);
+	i2c_set_clientdata(client, NULL);
+	kfree(tca);
+
+	return 0;
+}
+
+static struct i2c_driver tca6507_driver = {
+	.driver   = {
+		.name    = "leds-tca6507",
+		.owner   = THIS_MODULE,
+	},
+	.probe    = tca6507_probe,
+	.remove   = __devexit_p(tca6507_remove),
+	.id_table = tca6507_id,
+};
+
+static int __init tca6507_leds_init(void)
+{
+	return i2c_add_driver(&tca6507_driver);
+}
+
+static void __exit tca6507_leds_exit(void)
+{
+	i2c_del_driver(&tca6507_driver);
+}
+
+module_init(tca6507_leds_init);
+module_exit(tca6507_leds_exit);
+
+MODULE_AUTHOR("NeilBrown <neilb@suse.de>");
+MODULE_DESCRIPTION("TCA6507 LED/GPO driver");
+MODULE_LICENSE("GPL v2");

include/linux/leds-tca6507.h

@@ -0,0 +1,34 @@
+/*
+ * TCA6507 LED chip driver.
+ *
+ * Copyright (C) 2011 Neil Brown <neil@brown.name>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#ifndef __LINUX_TCA6507_H
+#define __LINUX_TCA6507_H
+#include <linux/leds.h>
+
+struct tca6507_platform_data {
+	struct led_platform_data leds;
+#ifdef CONFIG_GPIOLIB
+	int gpio_base;
+	void (*setup)(unsigned gpio_base, unsigned ngpio);
+#endif
+};
+
+#define	TCA6507_MAKE_GPIO 1
+#endif /* __LINUX_TCA6507_H*/