Merge branch 'omap7xx-fortony-rc3' of git://robotfuzz.com/linwizard-kernel into omap7xx

arch/arm/mach-omap1/board-fsample.c

@@ -107,7 +107,7 @@ static struct resource smc91x_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= INT_730_MPU_EXT_NIRQ,
+		.start	= INT_7XX_MPU_EXT_NIRQ,
 		.end	= 0,
 		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
 	},
@@ -196,8 +196,8 @@ static struct platform_device smc91x_device = {
 
 static struct resource kp_resources[] = {
 	[0] = {
-		.start	= INT_730_MPUIO_KEYPAD,
-		.end	= INT_730_MPUIO_KEYPAD,
+		.start	= INT_7XX_MPUIO_KEYPAD,
+		.end	= INT_7XX_MPUIO_KEYPAD,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -309,7 +309,7 @@ static void __init omap_fsample_map_io(void)
 	/*
 	 * Hold GSM Reset until needed
 	 */
-	omap_writew(omap_readw(OMAP730_DSP_M_CTL) & ~1, OMAP730_DSP_M_CTL);
+	omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
 
 	/*
 	 * UARTs -> done automagically by 8250 driver
@@ -320,21 +320,21 @@ static void __init omap_fsample_map_io(void)
 	 */
 
 	/* Flash: CS0 timings setup */
-	omap_writel(0x0000fff3, OMAP730_FLASH_CFG_0);
-	omap_writel(0x00000088, OMAP730_FLASH_ACFG_0);
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
+	omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
 
 	/*
 	 * Ethernet support through the debug board
 	 * CS1 timings setup
 	 */
-	omap_writel(0x0000fff3, OMAP730_FLASH_CFG_1);
-	omap_writel(0x00000000, OMAP730_FLASH_ACFG_1);
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
+	omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
 
 	/*
 	 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
 	 * It is used as the Ethernet controller interrupt
 	 */
-	omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
+	omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
 }
 
 MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")

arch/arm/mach-omap1/board-perseus2.c

@@ -74,7 +74,7 @@ static struct resource smc91x_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= INT_730_MPU_EXT_NIRQ,
+		.start	= INT_7XX_MPU_EXT_NIRQ,
 		.end	= 0,
 		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
 	},
@@ -163,8 +163,8 @@ static struct platform_device smc91x_device = {
 
 static struct resource kp_resources[] = {
 	[0] = {
-		.start	= INT_730_MPUIO_KEYPAD,
-		.end	= INT_730_MPUIO_KEYPAD,
+		.start	= INT_7XX_MPUIO_KEYPAD,
+		.end	= INT_7XX_MPUIO_KEYPAD,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -270,7 +270,7 @@ static void __init omap_perseus2_map_io(void)
 	/*
 	 * Hold GSM Reset until needed
 	 */
-	omap_writew(omap_readw(OMAP730_DSP_M_CTL) & ~1, OMAP730_DSP_M_CTL);
+	omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
 
 	/*
 	 * UARTs -> done automagically by 8250 driver
@@ -281,21 +281,21 @@ static void __init omap_perseus2_map_io(void)
 	 */
 
 	/* Flash: CS0 timings setup */
-	omap_writel(0x0000fff3, OMAP730_FLASH_CFG_0);
-	omap_writel(0x00000088, OMAP730_FLASH_ACFG_0);
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
+	omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
 
 	/*
 	 * Ethernet support through the debug board
 	 * CS1 timings setup
 	 */
-	omap_writel(0x0000fff3, OMAP730_FLASH_CFG_1);
-	omap_writel(0x00000000, OMAP730_FLASH_ACFG_1);
+	omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
+	omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
 
 	/*
 	 * Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
 	 * It is used as the Ethernet controller interrupt
 	 */
-	omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
+	omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
 }
 
 MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")

arch/arm/mach-omap1/clock.c

@@ -69,13 +69,13 @@ struct omap_clk {
 	}
 
 #define CK_310	(1 << 0)
-#define CK_730	(1 << 1)
+#define CK_7XX	(1 << 1)
 #define CK_1510	(1 << 2)
 #define CK_16XX	(1 << 3)
 
 static struct omap_clk omap_clks[] = {
 	/* non-ULPD clocks */
-	CLK(NULL,	"ck_ref",	&ck_ref,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"ck_ref",	&ck_ref,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
 	CLK(NULL,	"ck_dpll1",	&ck_dpll1,	CK_16XX | CK_1510 | CK_310),
 	/* CK_GEN1 clocks */
 	CLK(NULL,	"ck_dpll1out",	&ck_dpll1out.clk, CK_16XX),
@@ -83,7 +83,7 @@ static struct omap_clk omap_clks[] = {
 	CLK(NULL,	"arm_ck",	&arm_ck,	CK_16XX | CK_1510 | CK_310),
 	CLK(NULL,	"armper_ck",	&armper_ck.clk,	CK_16XX | CK_1510 | CK_310),
 	CLK(NULL,	"arm_gpio_ck",	&arm_gpio_ck,	CK_1510 | CK_310),
-	CLK(NULL,	"armxor_ck",	&armxor_ck.clk,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"armxor_ck",	&armxor_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
 	CLK(NULL,	"armtim_ck",	&armtim_ck.clk,	CK_16XX | CK_1510 | CK_310),
 	CLK("omap_wdt",	"fck",		&armwdt_ck.clk,	CK_16XX | CK_1510 | CK_310),
 	CLK("omap_wdt",	"ick",		&armper_ck.clk,	CK_16XX),
@@ -97,7 +97,7 @@ static struct omap_clk omap_clks[] = {
 	CLK(NULL,	"dspxor_ck",	&dspxor_ck,	CK_16XX | CK_1510 | CK_310),
 	CLK(NULL,	"dsptim_ck",	&dsptim_ck,	CK_16XX | CK_1510 | CK_310),
 	/* CK_GEN3 clocks */
-	CLK(NULL,	"tc_ck",	&tc_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_730),
+	CLK(NULL,	"tc_ck",	&tc_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
 	CLK(NULL,	"tipb_ck",	&tipb_ck,	CK_1510 | CK_310),
 	CLK(NULL,	"l3_ocpi_ck",	&l3_ocpi_ck,	CK_16XX),
 	CLK(NULL,	"tc1_ck",	&tc1_ck,	CK_16XX),
@@ -108,7 +108,7 @@ static struct omap_clk omap_clks[] = {
 	CLK(NULL,	"lb_ck",	&lb_ck.clk,	CK_1510 | CK_310),
 	CLK(NULL,	"rhea1_ck",	&rhea1_ck,	CK_16XX),
 	CLK(NULL,	"rhea2_ck",	&rhea2_ck,	CK_16XX),
-	CLK(NULL,	"lcd_ck",	&lcd_ck_16xx,	CK_16XX | CK_730),
+	CLK(NULL,	"lcd_ck",	&lcd_ck_16xx,	CK_16XX | CK_7XX),
 	CLK(NULL,	"lcd_ck",	&lcd_ck_1510.clk, CK_1510 | CK_310),
 	/* ULPD clocks */
 	CLK(NULL,	"uart1_ck",	&uart1_1510,	CK_1510 | CK_310),
@@ -398,7 +398,7 @@ static int omap1_select_table_rate(struct clk * clk, unsigned long rate)
 	 * Reprogramming the DPLL is tricky, it must be done from SRAM.
 	 * (on 730, bit 13 must always be 1)
 	 */
-	if (cpu_is_omap730())
+	if (cpu_is_omap7xx())
 		omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val | 0x2000);
 	else
 		omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
@@ -783,8 +783,8 @@ int __init omap1_clk_init(void)
 		cpu_mask |= CK_16XX;
 	if (cpu_is_omap1510())
 		cpu_mask |= CK_1510;
-	if (cpu_is_omap730())
-		cpu_mask |= CK_730;
+	if (cpu_is_omap7xx())
+		cpu_mask |= CK_7XX;
 	if (cpu_is_omap310())
 		cpu_mask |= CK_310;
 
@@ -800,7 +800,7 @@ int __init omap1_clk_init(void)
 			crystal_type = info->system_clock_type;
 	}
 
-#if defined(CONFIG_ARCH_OMAP730)
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 	ck_ref.rate = 13000000;
 #elif defined(CONFIG_ARCH_OMAP16XX)
 	if (crystal_type == 2)
@@ -847,7 +847,7 @@ int __init omap1_clk_init(void)
 		printk(KERN_ERR "System frequencies not set. Check your config.\n");
 		/* Guess sane values (60MHz) */
 		omap_writew(0x2290, DPLL_CTL);
-		omap_writew(cpu_is_omap730() ? 0x3005 : 0x1005, ARM_CKCTL);
+		omap_writew(cpu_is_omap7xx() ? 0x3005 : 0x1005, ARM_CKCTL);
 		ck_dpll1.rate = 60000000;
 	}
 #endif
@@ -862,7 +862,7 @@ int __init omap1_clk_init(void)
 
 #if defined(CONFIG_MACH_OMAP_PERSEUS2) || defined(CONFIG_MACH_OMAP_FSAMPLE)
 	/* Select slicer output as OMAP input clock */
-	omap_writew(omap_readw(OMAP730_PCC_UPLD_CTRL) & ~0x1, OMAP730_PCC_UPLD_CTRL);
+	omap_writew(omap_readw(OMAP7XX_PCC_UPLD_CTRL) & ~0x1, OMAP7XX_PCC_UPLD_CTRL);
 #endif
 
 	/* Amstrad Delta wants BCLK high when inactive */
@@ -873,7 +873,7 @@ int __init omap1_clk_init(void)
 
 	/* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
 	/* (on 730, bit 13 must not be cleared) */
-	if (cpu_is_omap730())
+	if (cpu_is_omap7xx())
 		omap_writew(omap_readw(ARM_CKCTL) & 0x2fff, ARM_CKCTL);
 	else
 		omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);

arch/arm/mach-omap1/io.c

@@ -36,33 +36,17 @@ static struct map_desc omap_io_desc[] __initdata = {
 	}
 };
 
-#ifdef CONFIG_ARCH_OMAP730
-static struct map_desc omap730_io_desc[] __initdata = {
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+static struct map_desc omap7xx_io_desc[] __initdata = {
 	{
-		.virtual	= OMAP730_DSP_BASE,
-		.pfn		= __phys_to_pfn(OMAP730_DSP_START),
-		.length		= OMAP730_DSP_SIZE,
+		.virtual	= OMAP7XX_DSP_BASE,
+		.pfn		= __phys_to_pfn(OMAP7XX_DSP_START),
+		.length		= OMAP7XX_DSP_SIZE,
 		.type		= MT_DEVICE
 	}, {
-		.virtual	= OMAP730_DSPREG_BASE,
-		.pfn		= __phys_to_pfn(OMAP730_DSPREG_START),
-		.length		= OMAP730_DSPREG_SIZE,
-		.type		= MT_DEVICE
-	}
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP850
-static struct map_desc omap850_io_desc[] __initdata = {
-	{
-		.virtual	= OMAP850_DSP_BASE,
-		.pfn		= __phys_to_pfn(OMAP850_DSP_START),
-		.length		= OMAP850_DSP_SIZE,
-		.type		= MT_DEVICE
-	}, {
-		.virtual	= OMAP850_DSPREG_BASE,
-		.pfn		= __phys_to_pfn(OMAP850_DSPREG_START),
-		.length		= OMAP850_DSPREG_SIZE,
+		.virtual	= OMAP7XX_DSPREG_BASE,
+		.pfn		= __phys_to_pfn(OMAP7XX_DSPREG_START),
+		.length		= OMAP7XX_DSPREG_SIZE,
 		.type		= MT_DEVICE
 	}
 };
@@ -120,18 +104,11 @@ void __init omap1_map_common_io(void)
 	 */
 	omap_check_revision();
 
-#ifdef CONFIG_ARCH_OMAP730
-	if (cpu_is_omap730()) {
-		iotable_init(omap730_io_desc, ARRAY_SIZE(omap730_io_desc));
-	}
-#endif
-
-#ifdef CONFIG_ARCH_OMAP850
-	if (cpu_is_omap850()) {
-		iotable_init(omap850_io_desc, ARRAY_SIZE(omap850_io_desc));
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+	if (cpu_is_omap7xx()) {
+		iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
 	}
 #endif
-
 #ifdef CONFIG_ARCH_OMAP15XX
 	if (cpu_is_omap15xx()) {
 		iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));

arch/arm/mach-omap1/irq.c

@@ -137,16 +137,8 @@ static void omap_irq_set_cfg(int irq, int fiq, int priority, int trigger)
 	irq_bank_writel(val, bank, offset);
 }
 
-#ifdef CONFIG_ARCH_OMAP730
-static struct omap_irq_bank omap730_irq_banks[] = {
-	{ .base_reg = OMAP_IH1_BASE,		.trigger_map = 0xb3f8e22f },
-	{ .base_reg = OMAP_IH2_BASE,		.trigger_map = 0xfdb9c1f2 },
-	{ .base_reg = OMAP_IH2_BASE + 0x100,	.trigger_map = 0x800040f3 },
-};
-#endif
-
-#ifdef CONFIG_ARCH_OMAP850
-static struct omap_irq_bank omap850_irq_banks[] = {
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+static struct omap_irq_bank omap7xx_irq_banks[] = {
 	{ .base_reg = OMAP_IH1_BASE,		.trigger_map = 0xb3f8e22f },
 	{ .base_reg = OMAP_IH2_BASE,		.trigger_map = 0xfdb9c1f2 },
 	{ .base_reg = OMAP_IH2_BASE + 0x100,	.trigger_map = 0x800040f3 },
@@ -186,16 +178,10 @@ void __init omap_init_irq(void)
 {
 	int i, j;
 
-#ifdef CONFIG_ARCH_OMAP730
-	if (cpu_is_omap730()) {
-		irq_banks = omap730_irq_banks;
-		irq_bank_count = ARRAY_SIZE(omap730_irq_banks);
-	}
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	if (cpu_is_omap850()) {
-		irq_banks = omap850_irq_banks;
-		irq_bank_count = ARRAY_SIZE(omap850_irq_banks);
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	if (cpu_is_omap7xx()) {
+		irq_banks = omap7xx_irq_banks;
+		irq_bank_count = ARRAY_SIZE(omap7xx_irq_banks);
 	}
 #endif
 #ifdef CONFIG_ARCH_OMAP15XX
@@ -247,10 +233,8 @@ void __init omap_init_irq(void)
 
 	/* Unmask level 2 handler */
 
-	if (cpu_is_omap730())
-		omap_unmask_irq(INT_730_IH2_IRQ);
-	else if (cpu_is_omap850())
-		omap_unmask_irq(INT_850_IH2_IRQ);
+	if (cpu_is_omap7xx())
+		omap_unmask_irq(INT_7XX_IH2_IRQ);
 	else if (cpu_is_omap15xx())
 		omap_unmask_irq(INT_1510_IH2_IRQ);
 	else if (cpu_is_omap16xx())

arch/arm/mach-omap1/mcbsp.c

@@ -79,29 +79,29 @@ static struct omap_mcbsp_ops omap1_mcbsp_ops = {
 	.free		= omap1_mcbsp_free,
 };
 
-#ifdef CONFIG_ARCH_OMAP730
-static struct omap_mcbsp_platform_data omap730_mcbsp_pdata[] = {
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+static struct omap_mcbsp_platform_data omap7xx_mcbsp_pdata[] = {
 	{
-		.phys_base	= OMAP730_MCBSP1_BASE,
+		.phys_base	= OMAP7XX_MCBSP1_BASE,
 		.dma_rx_sync	= OMAP_DMA_MCBSP1_RX,
 		.dma_tx_sync	= OMAP_DMA_MCBSP1_TX,
-		.rx_irq		= INT_730_McBSP1RX,
-		.tx_irq		= INT_730_McBSP1TX,
+		.rx_irq		= INT_7XX_McBSP1RX,
+		.tx_irq		= INT_7XX_McBSP1TX,
 		.ops		= &omap1_mcbsp_ops,
 	},
 	{
-		.phys_base	= OMAP730_MCBSP2_BASE,
+		.phys_base	= OMAP7XX_MCBSP2_BASE,
 		.dma_rx_sync	= OMAP_DMA_MCBSP3_RX,
 		.dma_tx_sync	= OMAP_DMA_MCBSP3_TX,
-		.rx_irq		= INT_730_McBSP2RX,
-		.tx_irq		= INT_730_McBSP2TX,
+		.rx_irq		= INT_7XX_McBSP2RX,
+		.tx_irq		= INT_7XX_McBSP2TX,
 		.ops		= &omap1_mcbsp_ops,
 	},
 };
-#define OMAP730_MCBSP_PDATA_SZ		ARRAY_SIZE(omap730_mcbsp_pdata)
+#define OMAP7XX_MCBSP_PDATA_SZ		ARRAY_SIZE(omap7xx_mcbsp_pdata)
 #else
-#define omap730_mcbsp_pdata		NULL
-#define OMAP730_MCBSP_PDATA_SZ		0
+#define omap7xx_mcbsp_pdata		NULL
+#define OMAP7XX_MCBSP_PDATA_SZ		0
 #endif
 
 #ifdef CONFIG_ARCH_OMAP15XX
@@ -172,8 +172,8 @@ static struct omap_mcbsp_platform_data omap16xx_mcbsp_pdata[] = {
 
 int __init omap1_mcbsp_init(void)
 {
-	if (cpu_is_omap730())
-		omap_mcbsp_count = OMAP730_MCBSP_PDATA_SZ;
+	if (cpu_is_omap7xx())
+		omap_mcbsp_count = OMAP7XX_MCBSP_PDATA_SZ;
 	if (cpu_is_omap15xx())
 		omap_mcbsp_count = OMAP15XX_MCBSP_PDATA_SZ;
 	if (cpu_is_omap16xx())
@@ -184,9 +184,9 @@ int __init omap1_mcbsp_init(void)
 	if (!mcbsp_ptr)
 		return -ENOMEM;
 
-	if (cpu_is_omap730())
-		omap_mcbsp_register_board_cfg(omap730_mcbsp_pdata,
-						OMAP730_MCBSP_PDATA_SZ);
+	if (cpu_is_omap7xx())
+		omap_mcbsp_register_board_cfg(omap7xx_mcbsp_pdata,
+						OMAP7XX_MCBSP_PDATA_SZ);
 
 	if (cpu_is_omap15xx())
 		omap_mcbsp_register_board_cfg(omap15xx_mcbsp_pdata,

arch/arm/mach-omap1/mux.c

@@ -35,47 +35,28 @@
 
 static struct omap_mux_cfg arch_mux_cfg;
 
-#ifdef CONFIG_ARCH_OMAP730
-static struct pin_config __initdata_or_module omap730_pins[] = {
-MUX_CFG_730("E2_730_KBR0",        12,   21,    0,   20,   1, 0)
-MUX_CFG_730("J7_730_KBR1",        12,   25,    0,   24,   1, 0)
-MUX_CFG_730("E1_730_KBR2",        12,   29,    0,   28,   1, 0)
-MUX_CFG_730("F3_730_KBR3",        13,    1,    0,    0,   1, 0)
-MUX_CFG_730("D2_730_KBR4",        13,    5,    0,    4,   1, 0)
-MUX_CFG_730("C2_730_KBC0",        13,    9,    0,    8,   1, 0)
-MUX_CFG_730("D3_730_KBC1",        13,   13,    0,   12,   1, 0)
-MUX_CFG_730("E4_730_KBC2",        13,   17,    0,   16,   1, 0)
-MUX_CFG_730("F4_730_KBC3",        13,   21,    0,   20,   1, 0)
-MUX_CFG_730("E3_730_KBC4",        13,   25,    0,   24,   1, 0)
-
-MUX_CFG_730("AA17_730_USB_DM",     2,   21,    0,   20,   0, 0)
-MUX_CFG_730("W16_730_USB_PU_EN",   2,   25,    0,   24,   0, 0)
-MUX_CFG_730("W17_730_USB_VBUSI",   2,   29,    0,   28,   0, 0)
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+static struct pin_config __initdata_or_module omap7xx_pins[] = {
+MUX_CFG_7XX("E2_7XX_KBR0",        12,   21,    0,   20,   1, 0)
+MUX_CFG_7XX("J7_7XX_KBR1",        12,   25,    0,   24,   1, 0)
+MUX_CFG_7XX("E1_7XX_KBR2",        12,   29,    0,   28,   1, 0)
+MUX_CFG_7XX("F3_7XX_KBR3",        13,    1,    0,    0,   1, 0)
+MUX_CFG_7XX("D2_7XX_KBR4",        13,    5,    0,    4,   1, 0)
+MUX_CFG_7XX("C2_7XX_KBC0",        13,    9,    0,    8,   1, 0)
+MUX_CFG_7XX("D3_7XX_KBC1",        13,   13,    0,   12,   1, 0)
+MUX_CFG_7XX("E4_7XX_KBC2",        13,   17,    0,   16,   1, 0)
+MUX_CFG_7XX("F4_7XX_KBC3",        13,   21,    0,   20,   1, 0)
+MUX_CFG_7XX("E3_7XX_KBC4",        13,   25,    0,   24,   1, 0)
+
+MUX_CFG_7XX("AA17_7XX_USB_DM",     2,   21,    0,   20,   0, 0)
+MUX_CFG_7XX("W16_7XX_USB_PU_EN",   2,   25,    0,   24,   0, 0)
+MUX_CFG_7XX("W17_7XX_USB_VBUSI",   2,   29,    0,   28,   0, 0)
 };
-#define OMAP730_PINS_SZ		ARRAY_SIZE(omap730_pins)
+#define OMAP7XX_PINS_SZ		ARRAY_SIZE(omap7xx_pins)
 #else
-#define omap730_pins		NULL
-#define OMAP730_PINS_SZ		0
-#endif	/* CONFIG_ARCH_OMAP730 */
-
-#ifdef CONFIG_ARCH_OMAP850
-struct pin_config __initdata_or_module omap850_pins[] = {
-MUX_CFG_850("E2_850_KBR0",        12,   21,    0,   20,   1, 0)
-MUX_CFG_850("J7_850_KBR1",        12,   25,    0,   24,   1, 0)
-MUX_CFG_850("E1_850_KBR2",        12,   29,    0,   28,   1, 0)
-MUX_CFG_850("F3_850_KBR3",        13,    1,    0,    0,   1, 0)
-MUX_CFG_850("D2_850_KBR4",        13,    5,    0,    4,   1, 0)
-MUX_CFG_850("C2_850_KBC0",        13,    9,    0,    8,   1, 0)
-MUX_CFG_850("D3_850_KBC1",        13,   13,    0,   12,   1, 0)
-MUX_CFG_850("E4_850_KBC2",        13,   17,    0,   16,   1, 0)
-MUX_CFG_850("F4_850_KBC3",        13,   21,    0,   20,   1, 0)
-MUX_CFG_850("E3_850_KBC4",        13,   25,    0,   24,   1, 0)
-
-MUX_CFG_850("AA17_850_USB_DM",     2,   21,    0,   20,   0, 0)
-MUX_CFG_850("W16_850_USB_PU_EN",   2,   25,    0,   24,   0, 0)
-MUX_CFG_850("W17_850_USB_VBUSI",   2,   29,    0,   28,   0, 0)
-};
-#endif
+#define omap7xx_pins		NULL
+#define OMAP7XX_PINS_SZ		0
+#endif	/* CONFIG_ARCH_OMAP730 || CONFIG_ARCH_OMAP850 */
 
 #if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX)
 static struct pin_config __initdata_or_module omap1xxx_pins[] = {
@@ -438,11 +419,6 @@ int __init_or_module omap1_cfg_reg(const struct pin_config *cfg)
 			printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
 			       cfg->pull_name, cfg->pull_reg, pull_orig, pull);
 	}
-
-#ifdef CONFIG_ARCH_OMAP850
-	omap_mux_register(omap850_pins, ARRAY_SIZE(omap850_pins));
-#endif
-
 #endif
 
 #ifdef CONFIG_OMAP_MUX_ERRORS
@@ -454,9 +430,9 @@ int __init_or_module omap1_cfg_reg(const struct pin_config *cfg)
 
 int __init omap1_mux_init(void)
 {
-	if (cpu_is_omap730()) {
-		arch_mux_cfg.pins	= omap730_pins;
-		arch_mux_cfg.size	= OMAP730_PINS_SZ;
+	if (cpu_is_omap7xx()) {
+		arch_mux_cfg.pins	= omap7xx_pins;
+		arch_mux_cfg.size	= OMAP7XX_PINS_SZ;
 		arch_mux_cfg.cfg_reg	= omap1_cfg_reg;
 	}
 

arch/arm/mach-omap1/pm.c

@@ -62,7 +62,7 @@
 static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
 static unsigned short dsp_sleep_save[DSP_SLEEP_SAVE_SIZE];
 static unsigned short ulpd_sleep_save[ULPD_SLEEP_SAVE_SIZE];
-static unsigned int mpui730_sleep_save[MPUI730_SLEEP_SAVE_SIZE];
+static unsigned int mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_SIZE];
 static unsigned int mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_SIZE];
 static unsigned int mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_SIZE];
 
@@ -183,9 +183,9 @@ static void omap_pm_wakeup_setup(void)
 	 * drivers must still separately call omap_set_gpio_wakeup() to
 	 * wake up to a GPIO interrupt.
 	 */
-	if (cpu_is_omap730())
-		level1_wake = OMAP_IRQ_BIT(INT_730_GPIO_BANK1) |
-			OMAP_IRQ_BIT(INT_730_IH2_IRQ);
+	if (cpu_is_omap7xx())
+		level1_wake = OMAP_IRQ_BIT(INT_7XX_GPIO_BANK1) |
+			OMAP_IRQ_BIT(INT_7XX_IH2_IRQ);
 	else if (cpu_is_omap15xx())
 		level1_wake = OMAP_IRQ_BIT(INT_GPIO_BANK1) |
 			OMAP_IRQ_BIT(INT_1510_IH2_IRQ);
@@ -195,10 +195,10 @@ static void omap_pm_wakeup_setup(void)
 
 	omap_writel(~level1_wake, OMAP_IH1_MIR);
 
-	if (cpu_is_omap730()) {
+	if (cpu_is_omap7xx()) {
 		omap_writel(~level2_wake, OMAP_IH2_0_MIR);
-		omap_writel(~(OMAP_IRQ_BIT(INT_730_WAKE_UP_REQ) |
-				OMAP_IRQ_BIT(INT_730_MPUIO_KEYPAD)),
+		omap_writel(~(OMAP_IRQ_BIT(INT_7XX_WAKE_UP_REQ) |
+				OMAP_IRQ_BIT(INT_7XX_MPUIO_KEYPAD)),
 				OMAP_IH2_1_MIR);
 	} else if (cpu_is_omap15xx()) {
 		level2_wake |= OMAP_IRQ_BIT(INT_KEYBOARD);
@@ -253,15 +253,15 @@ void omap1_pm_suspend(void)
 	 * Save interrupt, MPUI, ARM and UPLD control registers.
 	 */
 
-	if (cpu_is_omap730()) {
-		MPUI730_SAVE(OMAP_IH1_MIR);
-		MPUI730_SAVE(OMAP_IH2_0_MIR);
-		MPUI730_SAVE(OMAP_IH2_1_MIR);
-		MPUI730_SAVE(MPUI_CTRL);
-		MPUI730_SAVE(MPUI_DSP_BOOT_CONFIG);
-		MPUI730_SAVE(MPUI_DSP_API_CONFIG);
-		MPUI730_SAVE(EMIFS_CONFIG);
-		MPUI730_SAVE(EMIFF_SDRAM_CONFIG);
+	if (cpu_is_omap7xx()) {
+		MPUI7XX_SAVE(OMAP_IH1_MIR);
+		MPUI7XX_SAVE(OMAP_IH2_0_MIR);
+		MPUI7XX_SAVE(OMAP_IH2_1_MIR);
+		MPUI7XX_SAVE(MPUI_CTRL);
+		MPUI7XX_SAVE(MPUI_DSP_BOOT_CONFIG);
+		MPUI7XX_SAVE(MPUI_DSP_API_CONFIG);
+		MPUI7XX_SAVE(EMIFS_CONFIG);
+		MPUI7XX_SAVE(EMIFF_SDRAM_CONFIG);
 
 	} else if (cpu_is_omap15xx()) {
 		MPUI1510_SAVE(OMAP_IH1_MIR);
@@ -306,7 +306,7 @@ void omap1_pm_suspend(void)
 	omap_writew(omap_readw(ARM_RSTCT1) & ~(1 << DSP_EN), ARM_RSTCT1);
 
 		/* shut down dsp_ck */
-	if (!cpu_is_omap730())
+	if (!cpu_is_omap7xx())
 		omap_writew(omap_readw(ARM_CKCTL) & ~(1 << EN_DSPCK), ARM_CKCTL);
 
 	/* temporarily enabling api_ck to access DSP registers */
@@ -383,12 +383,12 @@ void omap1_pm_suspend(void)
 	ULPD_RESTORE(ULPD_CLOCK_CTRL);
 	ULPD_RESTORE(ULPD_STATUS_REQ);
 
-	if (cpu_is_omap730()) {
-		MPUI730_RESTORE(EMIFS_CONFIG);
-		MPUI730_RESTORE(EMIFF_SDRAM_CONFIG);
-		MPUI730_RESTORE(OMAP_IH1_MIR);
-		MPUI730_RESTORE(OMAP_IH2_0_MIR);
-		MPUI730_RESTORE(OMAP_IH2_1_MIR);
+	if (cpu_is_omap7xx()) {
+		MPUI7XX_RESTORE(EMIFS_CONFIG);
+		MPUI7XX_RESTORE(EMIFF_SDRAM_CONFIG);
+		MPUI7XX_RESTORE(OMAP_IH1_MIR);
+		MPUI7XX_RESTORE(OMAP_IH2_0_MIR);
+		MPUI7XX_RESTORE(OMAP_IH2_1_MIR);
 	} else if (cpu_is_omap15xx()) {
 		MPUI1510_RESTORE(MPUI_CTRL);
 		MPUI1510_RESTORE(MPUI_DSP_BOOT_CONFIG);
@@ -461,13 +461,13 @@ static int omap_pm_read_proc(
 	ULPD_SAVE(ULPD_DPLL_CTRL);
 	ULPD_SAVE(ULPD_POWER_CTRL);
 
-	if (cpu_is_omap730()) {
-		MPUI730_SAVE(MPUI_CTRL);
-		MPUI730_SAVE(MPUI_DSP_STATUS);
-		MPUI730_SAVE(MPUI_DSP_BOOT_CONFIG);
-		MPUI730_SAVE(MPUI_DSP_API_CONFIG);
-		MPUI730_SAVE(EMIFF_SDRAM_CONFIG);
-		MPUI730_SAVE(EMIFS_CONFIG);
+	if (cpu_is_omap7xx()) {
+		MPUI7XX_SAVE(MPUI_CTRL);
+		MPUI7XX_SAVE(MPUI_DSP_STATUS);
+		MPUI7XX_SAVE(MPUI_DSP_BOOT_CONFIG);
+		MPUI7XX_SAVE(MPUI_DSP_API_CONFIG);
+		MPUI7XX_SAVE(EMIFF_SDRAM_CONFIG);
+		MPUI7XX_SAVE(EMIFS_CONFIG);
 	} else if (cpu_is_omap15xx()) {
 		MPUI1510_SAVE(MPUI_CTRL);
 		MPUI1510_SAVE(MPUI_DSP_STATUS);
@@ -517,20 +517,20 @@ static int omap_pm_read_proc(
 		   ULPD_SHOW(ULPD_STATUS_REQ),
 		   ULPD_SHOW(ULPD_POWER_CTRL));
 
-		if (cpu_is_omap730()) {
+		if (cpu_is_omap7xx()) {
 			my_buffer_offset += sprintf(my_base + my_buffer_offset,
-			   "MPUI730_CTRL_REG	     0x%-8x \n"
-			   "MPUI730_DSP_STATUS_REG:      0x%-8x \n"
-			   "MPUI730_DSP_BOOT_CONFIG_REG: 0x%-8x \n"
-			   "MPUI730_DSP_API_CONFIG_REG:  0x%-8x \n"
-			   "MPUI730_SDRAM_CONFIG_REG:    0x%-8x \n"
-			   "MPUI730_EMIFS_CONFIG_REG:    0x%-8x \n",
-			   MPUI730_SHOW(MPUI_CTRL),
-			   MPUI730_SHOW(MPUI_DSP_STATUS),
-			   MPUI730_SHOW(MPUI_DSP_BOOT_CONFIG),
-			   MPUI730_SHOW(MPUI_DSP_API_CONFIG),
-			   MPUI730_SHOW(EMIFF_SDRAM_CONFIG),
-			   MPUI730_SHOW(EMIFS_CONFIG));
+			   "MPUI7XX_CTRL_REG	     0x%-8x \n"
+			   "MPUI7XX_DSP_STATUS_REG:      0x%-8x \n"
+			   "MPUI7XX_DSP_BOOT_CONFIG_REG: 0x%-8x \n"
+			   "MPUI7XX_DSP_API_CONFIG_REG:  0x%-8x \n"
+			   "MPUI7XX_SDRAM_CONFIG_REG:    0x%-8x \n"
+			   "MPUI7XX_EMIFS_CONFIG_REG:    0x%-8x \n",
+			   MPUI7XX_SHOW(MPUI_CTRL),
+			   MPUI7XX_SHOW(MPUI_DSP_STATUS),
+			   MPUI7XX_SHOW(MPUI_DSP_BOOT_CONFIG),
+			   MPUI7XX_SHOW(MPUI_DSP_API_CONFIG),
+			   MPUI7XX_SHOW(EMIFF_SDRAM_CONFIG),
+			   MPUI7XX_SHOW(EMIFS_CONFIG));
 		} else if (cpu_is_omap15xx()) {
 			my_buffer_offset += sprintf(my_base + my_buffer_offset,
 			   "MPUI1510_CTRL_REG             0x%-8x \n"
@@ -668,9 +668,9 @@ static int __init omap_pm_init(void)
 	 * These routines need to be in SRAM as that's the only
 	 * memory the MPU can see when it wakes up.
 	 */
-	if (cpu_is_omap730()) {
-		omap_sram_suspend = omap_sram_push(omap730_cpu_suspend,
-						   omap730_cpu_suspend_sz);
+	if (cpu_is_omap7xx()) {
+		omap_sram_suspend = omap_sram_push(omap7xx_cpu_suspend,
+						   omap7xx_cpu_suspend_sz);
 	} else if (cpu_is_omap15xx()) {
 		omap_sram_suspend = omap_sram_push(omap1510_cpu_suspend,
 						   omap1510_cpu_suspend_sz);
@@ -686,8 +686,8 @@ static int __init omap_pm_init(void)
 
 	pm_idle = omap1_pm_idle;
 
-	if (cpu_is_omap730())
-		setup_irq(INT_730_WAKE_UP_REQ, &omap_wakeup_irq);
+	if (cpu_is_omap7xx())
+		setup_irq(INT_7XX_WAKE_UP_REQ, &omap_wakeup_irq);
 	else if (cpu_is_omap16xx())
 		setup_irq(INT_1610_WAKE_UP_REQ, &omap_wakeup_irq);
 
@@ -700,8 +700,8 @@ static int __init omap_pm_init(void)
 	omap_writew(ULPD_POWER_CTRL_REG_VAL, ULPD_POWER_CTRL);
 
 	/* Configure IDLECT3 */
-	if (cpu_is_omap730())
-		omap_writel(OMAP730_IDLECT3_VAL, OMAP730_IDLECT3);
+	if (cpu_is_omap7xx())
+		omap_writel(OMAP7XX_IDLECT3_VAL, OMAP7XX_IDLECT3);
 	else if (cpu_is_omap16xx())
 		omap_writel(OMAP1610_IDLECT3_VAL, OMAP1610_IDLECT3);
 

arch/arm/mach-omap1/pm.h

@@ -98,13 +98,14 @@
 #define OMAP1610_IDLECT3		0xfffece24
 #define OMAP1610_IDLE_LOOP_REQUEST	0x0400
 
-#define OMAP730_IDLECT1_SLEEP_VAL	0x16c7
-#define OMAP730_IDLECT2_SLEEP_VAL	0x09c7
-#define OMAP730_IDLECT3_VAL		0x3f
-#define OMAP730_IDLECT3		0xfffece24
-#define OMAP730_IDLE_LOOP_REQUEST	0x0C00
+#define OMAP7XX_IDLECT1_SLEEP_VAL	0x16c7
+#define OMAP7XX_IDLECT2_SLEEP_VAL	0x09c7
+#define OMAP7XX_IDLECT3_VAL		0x3f
+#define OMAP7XX_IDLECT3		0xfffece24
+#define OMAP7XX_IDLE_LOOP_REQUEST	0x0C00
 
 #if     !defined(CONFIG_ARCH_OMAP730) && \
+	!defined(CONFIG_ARCH_OMAP850) && \
 	!defined(CONFIG_ARCH_OMAP15XX) && \
 	!defined(CONFIG_ARCH_OMAP16XX)
 #warning "Power management for this processor not implemented yet"
@@ -122,17 +123,17 @@ extern void allow_idle_sleep(void);
 extern void omap1_pm_idle(void);
 extern void omap1_pm_suspend(void);
 
-extern void omap730_cpu_suspend(unsigned short, unsigned short);
+extern void omap7xx_cpu_suspend(unsigned short, unsigned short);
 extern void omap1510_cpu_suspend(unsigned short, unsigned short);
 extern void omap1610_cpu_suspend(unsigned short, unsigned short);
-extern void omap730_idle_loop_suspend(void);
+extern void omap7xx_idle_loop_suspend(void);
 extern void omap1510_idle_loop_suspend(void);
 extern void omap1610_idle_loop_suspend(void);
 
-extern unsigned int omap730_cpu_suspend_sz;
+extern unsigned int omap7xx_cpu_suspend_sz;
 extern unsigned int omap1510_cpu_suspend_sz;
 extern unsigned int omap1610_cpu_suspend_sz;
-extern unsigned int omap730_idle_loop_suspend_sz;
+extern unsigned int omap7xx_idle_loop_suspend_sz;
 extern unsigned int omap1510_idle_loop_suspend_sz;
 extern unsigned int omap1610_idle_loop_suspend_sz;
 
@@ -155,9 +156,9 @@ extern void omap_serial_wake_trigger(int enable);
 #define ULPD_RESTORE(x) omap_writew((ulpd_sleep_save[ULPD_SLEEP_SAVE_##x]), (x))
 #define ULPD_SHOW(x) ulpd_sleep_save[ULPD_SLEEP_SAVE_##x]
 
-#define MPUI730_SAVE(x) mpui730_sleep_save[MPUI730_SLEEP_SAVE_##x] = omap_readl(x)
-#define MPUI730_RESTORE(x) omap_writel((mpui730_sleep_save[MPUI730_SLEEP_SAVE_##x]), (x))
-#define MPUI730_SHOW(x) mpui730_sleep_save[MPUI730_SLEEP_SAVE_##x]
+#define MPUI7XX_SAVE(x) mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x] = omap_readl(x)
+#define MPUI7XX_RESTORE(x) omap_writel((mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x]), (x))
+#define MPUI7XX_SHOW(x) mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x]
 
 #define MPUI1510_SAVE(x) mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_##x] = omap_readl(x)
 #define MPUI1510_RESTORE(x) omap_writel((mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_##x]), (x))
@@ -232,24 +233,24 @@ enum mpui1510_save_state {
 #endif
 };
 
-enum mpui730_save_state {
-	MPUI730_SLEEP_SAVE_START = 0,
+enum mpui7xx_save_state {
+	MPUI7XX_SLEEP_SAVE_START = 0,
 	/*
 	 * MPUI registers 32 bits
 	 */
-	MPUI730_SLEEP_SAVE_MPUI_CTRL,
-	MPUI730_SLEEP_SAVE_MPUI_DSP_BOOT_CONFIG,
-	MPUI730_SLEEP_SAVE_MPUI_DSP_API_CONFIG,
-	MPUI730_SLEEP_SAVE_MPUI_DSP_STATUS,
-	MPUI730_SLEEP_SAVE_EMIFF_SDRAM_CONFIG,
-	MPUI730_SLEEP_SAVE_EMIFS_CONFIG,
-	MPUI730_SLEEP_SAVE_OMAP_IH1_MIR,
-	MPUI730_SLEEP_SAVE_OMAP_IH2_0_MIR,
-	MPUI730_SLEEP_SAVE_OMAP_IH2_1_MIR,
-#if defined(CONFIG_ARCH_OMAP730)
-	MPUI730_SLEEP_SAVE_SIZE
+	MPUI7XX_SLEEP_SAVE_MPUI_CTRL,
+	MPUI7XX_SLEEP_SAVE_MPUI_DSP_BOOT_CONFIG,
+	MPUI7XX_SLEEP_SAVE_MPUI_DSP_API_CONFIG,
+	MPUI7XX_SLEEP_SAVE_MPUI_DSP_STATUS,
+	MPUI7XX_SLEEP_SAVE_EMIFF_SDRAM_CONFIG,
+	MPUI7XX_SLEEP_SAVE_EMIFS_CONFIG,
+	MPUI7XX_SLEEP_SAVE_OMAP_IH1_MIR,
+	MPUI7XX_SLEEP_SAVE_OMAP_IH2_0_MIR,
+	MPUI7XX_SLEEP_SAVE_OMAP_IH2_1_MIR,
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	MPUI7XX_SLEEP_SAVE_SIZE
 #else
-	MPUI730_SLEEP_SAVE_SIZE = 0
+	MPUI7XX_SLEEP_SAVE_SIZE = 0
 #endif
 };
 

arch/arm/mach-omap1/serial.c

@@ -110,18 +110,11 @@ void __init omap_serial_init(void)
 {
 	int i;
 
-	if (cpu_is_omap730()) {
+	if (cpu_is_omap7xx()) {
 		serial_platform_data[0].regshift = 0;
 		serial_platform_data[1].regshift = 0;
-		serial_platform_data[0].irq = INT_730_UART_MODEM_1;
-		serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
-	}
-
-	if (cpu_is_omap850()) {
-		serial_platform_data[0].regshift = 0;
-		serial_platform_data[1].regshift = 0;
-		serial_platform_data[0].irq = INT_850_UART_MODEM_1;
-		serial_platform_data[1].irq = INT_850_UART_MODEM_IRDA_2;
+		serial_platform_data[0].irq = INT_7XX_UART_MODEM_1;
+		serial_platform_data[1].irq = INT_7XX_UART_MODEM_IRDA_2;
 	}
 
 	if (cpu_is_omap15xx()) {

arch/arm/mach-omap1/sleep.S

@@ -1,7 +1,7 @@
 /*
  * linux/arch/arm/mach-omap1/sleep.S
  *
- * Low-level OMAP730/1510/1610 sleep/wakeUp support
+ * Low-level OMAP7XX/1510/1610 sleep/wakeUp support
  *
  * Initial SA1110 code:
  * Copyright (c) 2001 Cliff Brake <cbrake@accelent.com>
@@ -57,8 +57,8 @@
  *
  */
 
-#if defined(CONFIG_ARCH_OMAP730)
-ENTRY(omap730_cpu_suspend)
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ENTRY(omap7xx_cpu_suspend)
 
 	@ save registers on stack
 	stmfd	sp!, {r0 - r12, lr}
@@ -91,13 +91,13 @@ ENTRY(omap730_cpu_suspend)
 
 	@ turn off clock domains
 	@ do not disable PERCK (0x04)
-	mov	r5, #OMAP730_IDLECT2_SLEEP_VAL & 0xff
-	orr	r5, r5, #OMAP730_IDLECT2_SLEEP_VAL & 0xff00
+	mov	r5, #OMAP7XX_IDLECT2_SLEEP_VAL & 0xff
+	orr	r5, r5, #OMAP7XX_IDLECT2_SLEEP_VAL & 0xff00
 	strh	r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
 
 	@ request ARM idle
-	mov	r3, #OMAP730_IDLECT1_SLEEP_VAL & 0xff
-	orr	r3, r3, #OMAP730_IDLECT1_SLEEP_VAL & 0xff00
+	mov	r3, #OMAP7XX_IDLECT1_SLEEP_VAL & 0xff
+	orr	r3, r3, #OMAP7XX_IDLECT1_SLEEP_VAL & 0xff00
 	strh	r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
 
 	@ disable instruction cache
@@ -113,7 +113,7 @@ ENTRY(omap730_cpu_suspend)
 	mov	r2, #0
 	mcr	p15, 0, r2, c7, c0, 4		@ wait for interrupt
 /*
- * omap730_cpu_suspend()'s resume point.
+ * omap7xx_cpu_suspend()'s resume point.
  *
  * It will just start executing here, so we'll restore stuff from the
  * stack.
@@ -132,9 +132,9 @@ ENTRY(omap730_cpu_suspend)
 	@ restore regs and return
 	ldmfd	sp!, {r0 - r12, pc}
 
-ENTRY(omap730_cpu_suspend_sz)
-	.word	. - omap730_cpu_suspend
-#endif /* CONFIG_ARCH_OMAP730 */
+ENTRY(omap7xx_cpu_suspend_sz)
+	.word	. - omap7xx_cpu_suspend
+#endif /* CONFIG_ARCH_OMAP730 || CONFIG_ARCH_OMAP850 */
 
 #ifdef CONFIG_ARCH_OMAP15XX
 ENTRY(omap1510_cpu_suspend)

arch/arm/plat-omap/devices.c

@@ -113,17 +113,17 @@ static void omap_init_kp(void)
 		omap_cfg_reg(E19_1610_KBR4);
 		omap_cfg_reg(N19_1610_KBR5);
 	} else if (machine_is_omap_perseus2() || machine_is_omap_fsample()) {
-		omap_cfg_reg(E2_730_KBR0);
-		omap_cfg_reg(J7_730_KBR1);
-		omap_cfg_reg(E1_730_KBR2);
-		omap_cfg_reg(F3_730_KBR3);
-		omap_cfg_reg(D2_730_KBR4);
-
-		omap_cfg_reg(C2_730_KBC0);
-		omap_cfg_reg(D3_730_KBC1);
-		omap_cfg_reg(E4_730_KBC2);
-		omap_cfg_reg(F4_730_KBC3);
-		omap_cfg_reg(E3_730_KBC4);
+		omap_cfg_reg(E2_7XX_KBR0);
+		omap_cfg_reg(J7_7XX_KBR1);
+		omap_cfg_reg(E1_7XX_KBR2);
+		omap_cfg_reg(F3_7XX_KBR3);
+		omap_cfg_reg(D2_7XX_KBR4);
+
+		omap_cfg_reg(C2_7XX_KBC0);
+		omap_cfg_reg(D3_7XX_KBC1);
+		omap_cfg_reg(E4_7XX_KBC2);
+		omap_cfg_reg(F4_7XX_KBC3);
+		omap_cfg_reg(E3_7XX_KBC4);
 	} else if (machine_is_omap_h4()) {
 		omap_cfg_reg(T19_24XX_KBR0);
 		omap_cfg_reg(R19_24XX_KBR1);

arch/arm/plat-omap/gpio.c

@@ -68,36 +68,20 @@
 #define OMAP1610_GPIO_SET_DATAOUT	0x00f0
 
 /*
- * OMAP730 specific GPIO registers
+ * OMAP7XX specific GPIO registers
  */
-#define OMAP730_GPIO1_BASE		OMAP1_IO_ADDRESS(0xfffbc000)
-#define OMAP730_GPIO2_BASE		OMAP1_IO_ADDRESS(0xfffbc800)
-#define OMAP730_GPIO3_BASE		OMAP1_IO_ADDRESS(0xfffbd000)
-#define OMAP730_GPIO4_BASE		OMAP1_IO_ADDRESS(0xfffbd800)
-#define OMAP730_GPIO5_BASE		OMAP1_IO_ADDRESS(0xfffbe000)
-#define OMAP730_GPIO6_BASE		OMAP1_IO_ADDRESS(0xfffbe800)
-#define OMAP730_GPIO_DATA_INPUT		0x00
-#define OMAP730_GPIO_DATA_OUTPUT	0x04
-#define OMAP730_GPIO_DIR_CONTROL	0x08
-#define OMAP730_GPIO_INT_CONTROL	0x0c
-#define OMAP730_GPIO_INT_MASK		0x10
-#define OMAP730_GPIO_INT_STATUS		0x14
-
-/*
- * OMAP850 specific GPIO registers
- */
-#define OMAP850_GPIO1_BASE		OMAP1_IO_ADDRESS(0xfffbc000)
-#define OMAP850_GPIO2_BASE		OMAP1_IO_ADDRESS(0xfffbc800)
-#define OMAP850_GPIO3_BASE		OMAP1_IO_ADDRESS(0xfffbd000)
-#define OMAP850_GPIO4_BASE		OMAP1_IO_ADDRESS(0xfffbd800)
-#define OMAP850_GPIO5_BASE		OMAP1_IO_ADDRESS(0xfffbe000)
-#define OMAP850_GPIO6_BASE		OMAP1_IO_ADDRESS(0xfffbe800)
-#define OMAP850_GPIO_DATA_INPUT		0x00
-#define OMAP850_GPIO_DATA_OUTPUT	0x04
-#define OMAP850_GPIO_DIR_CONTROL	0x08
-#define OMAP850_GPIO_INT_CONTROL	0x0c
-#define OMAP850_GPIO_INT_MASK		0x10
-#define OMAP850_GPIO_INT_STATUS		0x14
+#define OMAP7XX_GPIO1_BASE		OMAP1_IO_ADDRESS(0xfffbc000)
+#define OMAP7XX_GPIO2_BASE		OMAP1_IO_ADDRESS(0xfffbc800)
+#define OMAP7XX_GPIO3_BASE		OMAP1_IO_ADDRESS(0xfffbd000)
+#define OMAP7XX_GPIO4_BASE		OMAP1_IO_ADDRESS(0xfffbd800)
+#define OMAP7XX_GPIO5_BASE		OMAP1_IO_ADDRESS(0xfffbe000)
+#define OMAP7XX_GPIO6_BASE		OMAP1_IO_ADDRESS(0xfffbe800)
+#define OMAP7XX_GPIO_DATA_INPUT		0x00
+#define OMAP7XX_GPIO_DATA_OUTPUT	0x04
+#define OMAP7XX_GPIO_DIR_CONTROL	0x08
+#define OMAP7XX_GPIO_INT_CONTROL	0x0c
+#define OMAP7XX_GPIO_INT_MASK		0x10
+#define OMAP7XX_GPIO_INT_STATUS		0x14
 
 #define OMAP1_MPUIO_VBASE		OMAP1_IO_ADDRESS(OMAP1_MPUIO_BASE)
 
@@ -215,8 +199,7 @@ struct gpio_bank {
 #define METHOD_MPUIO		0
 #define METHOD_GPIO_1510	1
 #define METHOD_GPIO_1610	2
-#define METHOD_GPIO_730		3
-#define METHOD_GPIO_850		4
+#define METHOD_GPIO_7XX		3
 #define METHOD_GPIO_24XX	5
 
 #ifdef CONFIG_ARCH_OMAP16XX
@@ -236,31 +219,18 @@ static struct gpio_bank gpio_bank_1510[2] = {
 };
 #endif
 
-#ifdef CONFIG_ARCH_OMAP730
-static struct gpio_bank gpio_bank_730[7] = {
-	{ OMAP1_MPUIO_VBASE,    INT_730_MPUIO,	    IH_MPUIO_BASE,	METHOD_MPUIO },
-	{ OMAP730_GPIO1_BASE,  INT_730_GPIO_BANK1,  IH_GPIO_BASE,	METHOD_GPIO_730 },
-	{ OMAP730_GPIO2_BASE,  INT_730_GPIO_BANK2,  IH_GPIO_BASE + 32,	METHOD_GPIO_730 },
-	{ OMAP730_GPIO3_BASE,  INT_730_GPIO_BANK3,  IH_GPIO_BASE + 64,	METHOD_GPIO_730 },
-	{ OMAP730_GPIO4_BASE,  INT_730_GPIO_BANK4,  IH_GPIO_BASE + 96,	METHOD_GPIO_730 },
-	{ OMAP730_GPIO5_BASE,  INT_730_GPIO_BANK5,  IH_GPIO_BASE + 128, METHOD_GPIO_730 },
-	{ OMAP730_GPIO6_BASE,  INT_730_GPIO_BANK6,  IH_GPIO_BASE + 160, METHOD_GPIO_730 },
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+static struct gpio_bank gpio_bank_7xx[7] = {
+	{ OMAP1_MPUIO_VBASE,    INT_7XX_MPUIO,	    IH_MPUIO_BASE,	METHOD_MPUIO },
+	{ OMAP7XX_GPIO1_BASE,  INT_7XX_GPIO_BANK1,  IH_GPIO_BASE,	METHOD_GPIO_7XX },
+	{ OMAP7XX_GPIO2_BASE,  INT_7XX_GPIO_BANK2,  IH_GPIO_BASE + 32,	METHOD_GPIO_7XX },
+	{ OMAP7XX_GPIO3_BASE,  INT_7XX_GPIO_BANK3,  IH_GPIO_BASE + 64,	METHOD_GPIO_7XX },
+	{ OMAP7XX_GPIO4_BASE,  INT_7XX_GPIO_BANK4,  IH_GPIO_BASE + 96,	METHOD_GPIO_7XX },
+	{ OMAP7XX_GPIO5_BASE,  INT_7XX_GPIO_BANK5,  IH_GPIO_BASE + 128, METHOD_GPIO_7XX },
+	{ OMAP7XX_GPIO6_BASE,  INT_7XX_GPIO_BANK6,  IH_GPIO_BASE + 160, METHOD_GPIO_7XX },
 };
 #endif
 
-#ifdef CONFIG_ARCH_OMAP850
-static struct gpio_bank gpio_bank_850[7] = {
-	{ OMAP1_MPUIO_VBASE,     INT_850_MPUIO,	    IH_MPUIO_BASE,	METHOD_MPUIO },
-	{ OMAP850_GPIO1_BASE,  INT_850_GPIO_BANK1,  IH_GPIO_BASE,	METHOD_GPIO_850 },
-	{ OMAP850_GPIO2_BASE,  INT_850_GPIO_BANK2,  IH_GPIO_BASE + 32,	METHOD_GPIO_850 },
-	{ OMAP850_GPIO3_BASE,  INT_850_GPIO_BANK3,  IH_GPIO_BASE + 64,	METHOD_GPIO_850 },
-	{ OMAP850_GPIO4_BASE,  INT_850_GPIO_BANK4,  IH_GPIO_BASE + 96,	METHOD_GPIO_850 },
-	{ OMAP850_GPIO5_BASE,  INT_850_GPIO_BANK5,  IH_GPIO_BASE + 128, METHOD_GPIO_850 },
-	{ OMAP850_GPIO6_BASE,  INT_850_GPIO_BANK6,  IH_GPIO_BASE + 160, METHOD_GPIO_850 },
-};
-#endif
-
-
 #ifdef CONFIG_ARCH_OMAP24XX
 
 static struct gpio_bank gpio_bank_242x[4] = {
@@ -402,14 +372,9 @@ static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
 		reg += OMAP1610_GPIO_DIRECTION;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DIR_CONTROL;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DIR_CONTROL;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_DIR_CONTROL;
 		break;
 #endif
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
@@ -469,19 +434,9 @@ static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
 		l = 1 << gpio;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DATA_OUTPUT;
-		l = __raw_readl(reg);
-		if (enable)
-			l |= 1 << gpio;
-		else
-			l &= ~(1 << gpio);
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DATA_OUTPUT;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_DATA_OUTPUT;
 		l = __raw_readl(reg);
 		if (enable)
 			l |= 1 << gpio;
@@ -537,14 +492,9 @@ static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
 		reg += OMAP1610_GPIO_DATAIN;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DATA_INPUT;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DATA_INPUT;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_DATA_INPUT;
 		break;
 #endif
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
@@ -588,14 +538,9 @@ static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
 		reg += OMAP1610_GPIO_DATAOUT;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DATA_OUTPUT;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DATA_OUTPUT;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_DATA_OUTPUT;
 		break;
 #endif
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
@@ -797,21 +742,9 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger)
 			__raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA);
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_INT_CONTROL;
-		l = __raw_readl(reg);
-		if (trigger & IRQ_TYPE_EDGE_RISING)
-			l |= 1 << gpio;
-		else if (trigger & IRQ_TYPE_EDGE_FALLING)
-			l &= ~(1 << gpio);
-		else
-			goto bad;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_INT_CONTROL;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_INT_CONTROL;
 		l = __raw_readl(reg);
 		if (trigger & IRQ_TYPE_EDGE_RISING)
 			l |= 1 << gpio;
@@ -897,14 +830,9 @@ static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
 		reg += OMAP1610_GPIO_IRQSTATUS1;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_INT_STATUS;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_INT_STATUS;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_INT_STATUS;
 		break;
 #endif
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
@@ -971,16 +899,9 @@ static u32 _get_gpio_irqbank_mask(struct gpio_bank *bank)
 		mask = 0xffff;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_INT_MASK;
-		mask = 0xffffffff;
-		inv = 1;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_INT_MASK;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_INT_MASK;
 		mask = 0xffffffff;
 		inv = 1;
 		break;
@@ -1044,19 +965,9 @@ static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enab
 		l = gpio_mask;
 		break;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_INT_MASK;
-		l = __raw_readl(reg);
-		if (enable)
-			l &= ~(gpio_mask);
-		else
-			l |= gpio_mask;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_INT_MASK;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_INT_MASK;
 		l = __raw_readl(reg);
 		if (enable)
 			l &= ~(gpio_mask);
@@ -1249,13 +1160,9 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 	if (bank->method == METHOD_GPIO_1610)
 		isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	if (bank->method == METHOD_GPIO_730)
-		isr_reg = bank->base + OMAP730_GPIO_INT_STATUS;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	if (bank->method == METHOD_GPIO_850)
-		isr_reg = bank->base + OMAP850_GPIO_INT_STATUS;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	if (bank->method == METHOD_GPIO_7XX)
+		isr_reg = bank->base + OMAP7XX_GPIO_INT_STATUS;
 #endif
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
 	if (bank->method == METHOD_GPIO_24XX)
@@ -1524,11 +1431,8 @@ static int gpio_is_input(struct gpio_bank *bank, int mask)
 	case METHOD_GPIO_1610:
 		reg += OMAP1610_GPIO_DIRECTION;
 		break;
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DIR_CONTROL;
+	case METHOD_GPIO_7XX:
+		reg += OMAP7XX_GPIO_DIR_CONTROL;
 		break;
 	case METHOD_GPIO_24XX:
 		reg += OMAP24XX_GPIO_OE;
@@ -1695,21 +1599,13 @@ static int __init _omap_gpio_init(void)
 		       (rev >> 4) & 0x0f, rev & 0x0f);
 	}
 #endif
-#ifdef CONFIG_ARCH_OMAP730
-	if (cpu_is_omap730()) {
-		printk(KERN_INFO "OMAP730 GPIO hardware\n");
-		gpio_bank_count = 7;
-		gpio_bank = gpio_bank_730;
-	}
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-	if (cpu_is_omap850()) {
-		printk(KERN_INFO "OMAP850 GPIO hardware\n");
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+	if (cpu_is_omap7xx()) {
+		printk(KERN_INFO "OMAP7XX GPIO hardware\n");
 		gpio_bank_count = 7;
-		gpio_bank = gpio_bank_850;
+		gpio_bank = gpio_bank_7xx;
 	}
 #endif
-
 #ifdef CONFIG_ARCH_OMAP24XX
 	if (cpu_is_omap242x()) {
 		int rev;
@@ -1768,11 +1664,11 @@ static int __init _omap_gpio_init(void)
 			__raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
 			__raw_writew(0x0014, bank->base + OMAP1610_GPIO_SYSCONFIG);
 		}
-		if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_730) {
-			__raw_writel(0xffffffff, bank->base + OMAP730_GPIO_INT_MASK);
-			__raw_writel(0x00000000, bank->base + OMAP730_GPIO_INT_STATUS);
+		if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_7XX) {
+			__raw_writel(0xffffffff, bank->base + OMAP7XX_GPIO_INT_MASK);
+			__raw_writel(0x00000000, bank->base + OMAP7XX_GPIO_INT_STATUS);
 
-			gpio_count = 32; /* 730 has 32-bit GPIOs */
+			gpio_count = 32; /* 7xx has 32-bit GPIOs */
 		}
 
 #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
@@ -2160,8 +2056,7 @@ static int dbg_gpio_show(struct seq_file *s, void *unused)
 
 		if (bank_is_mpuio(bank))
 			gpio = OMAP_MPUIO(0);
-		else if (cpu_class_is_omap2() || cpu_is_omap730() ||
-				cpu_is_omap850())
+		else if (cpu_class_is_omap2() || cpu_is_omap7xx())
 			bankwidth = 32;
 
 		for (j = 0; j < bankwidth; j++, gpio++, mask <<= 1) {

arch/arm/plat-omap/include/mach/entry-macro.S

@@ -17,11 +17,11 @@
 
 #if defined(CONFIG_ARCH_OMAP1)
 
-#if defined(CONFIG_ARCH_OMAP730) && \
+#if (defined(CONFIG_ARCH_OMAP730)||defined(CONFIG_ARCH_OMAP850)) && \
 	(defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX))
-#error "FIXME: OMAP730 doesn't support multiple-OMAP"
-#elif defined(CONFIG_ARCH_OMAP730)
-#define INT_IH2_IRQ		INT_730_IH2_IRQ
+#error "FIXME: OMAP7XX doesn't support multiple-OMAP"
+#elif defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+#define INT_IH2_IRQ		INT_7XX_IH2_IRQ
 #elif defined(CONFIG_ARCH_OMAP15XX)
 #define INT_IH2_IRQ		INT_1510_IH2_IRQ
 #elif defined(CONFIG_ARCH_OMAP16XX)

arch/arm/plat-omap/include/mach/hardware.h

@@ -280,7 +280,7 @@
  * ---------------------------------------------------------------------------
  */
 
-#include "omap730.h"
+#include "omap7xx.h"
 #include "omap1510.h"
 #include "omap16xx.h"
 #include "omap24xx.h"

arch/arm/plat-omap/include/mach/irqs.h

@@ -86,49 +86,26 @@
 #define INT_1610_SSR_FIFO_0	29
 
 /*
- * OMAP-730 specific IRQ numbers for interrupt handler 1
+ * OMAP-7xx specific IRQ numbers for interrupt handler 1
  */
-#define INT_730_IH2_FIQ		0
-#define INT_730_IH2_IRQ		1
-#define INT_730_USB_NON_ISO	2
-#define INT_730_USB_ISO		3
-#define INT_730_ICR		4
-#define INT_730_EAC		5
-#define INT_730_GPIO_BANK1	6
-#define INT_730_GPIO_BANK2	7
-#define INT_730_GPIO_BANK3	8
-#define INT_730_McBSP2TX	10
-#define INT_730_McBSP2RX	11
-#define INT_730_McBSP2RX_OVF	12
-#define INT_730_LCD_LINE	14
-#define INT_730_GSM_PROTECT	15
-#define INT_730_TIMER3		16
-#define INT_730_GPIO_BANK5	17
-#define INT_730_GPIO_BANK6	18
-#define INT_730_SPGIO_WR	29
-
-/*
- * OMAP-850 specific IRQ numbers for interrupt handler 1
- */
-#define INT_850_IH2_FIQ		0
-#define INT_850_IH2_IRQ		1
-#define INT_850_USB_NON_ISO	2
-#define INT_850_USB_ISO		3
-#define INT_850_ICR		4
-#define INT_850_EAC		5
-#define INT_850_GPIO_BANK1	6
-#define INT_850_GPIO_BANK2	7
-#define INT_850_GPIO_BANK3	8
-#define INT_850_McBSP2TX	10
-#define INT_850_McBSP2RX	11
-#define INT_850_McBSP2RX_OVF	12
-#define INT_850_LCD_LINE	14
-#define INT_850_GSM_PROTECT	15
-#define INT_850_TIMER3		16
-#define INT_850_GPIO_BANK5	17
-#define INT_850_GPIO_BANK6	18
-#define INT_850_SPGIO_WR	29
-
+#define INT_7XX_IH2_FIQ		0
+#define INT_7XX_IH2_IRQ		1
+#define INT_7XX_USB_NON_ISO	2
+#define INT_7XX_USB_ISO		3
+#define INT_7XX_ICR		4
+#define INT_7XX_EAC		5
+#define INT_7XX_GPIO_BANK1	6
+#define INT_7XX_GPIO_BANK2	7
+#define INT_7XX_GPIO_BANK3	8
+#define INT_7XX_McBSP2TX	10
+#define INT_7XX_McBSP2RX	11
+#define INT_7XX_McBSP2RX_OVF	12
+#define INT_7XX_LCD_LINE	14
+#define INT_7XX_GSM_PROTECT	15
+#define INT_7XX_TIMER3		16
+#define INT_7XX_GPIO_BANK5	17
+#define INT_7XX_GPIO_BANK6	18
+#define INT_7XX_SPGIO_WR	29
 
 /*
  * IRQ numbers for interrupt handler 2
@@ -206,120 +183,62 @@
 #define INT_1610_SHA1MD5	(91 + IH2_BASE)
 
 /*
- * OMAP-730 specific IRQ numbers for interrupt handler 2
- */
-#define INT_730_HW_ERRORS	(0 + IH2_BASE)
-#define INT_730_NFIQ_PWR_FAIL	(1 + IH2_BASE)
-#define INT_730_CFCD		(2 + IH2_BASE)
-#define INT_730_CFIREQ		(3 + IH2_BASE)
-#define INT_730_I2C		(4 + IH2_BASE)
-#define INT_730_PCC		(5 + IH2_BASE)
-#define INT_730_MPU_EXT_NIRQ	(6 + IH2_BASE)
-#define INT_730_SPI_100K_1	(7 + IH2_BASE)
-#define INT_730_SYREN_SPI	(8 + IH2_BASE)
-#define INT_730_VLYNQ		(9 + IH2_BASE)
-#define INT_730_GPIO_BANK4	(10 + IH2_BASE)
-#define INT_730_McBSP1TX	(11 + IH2_BASE)
-#define INT_730_McBSP1RX	(12 + IH2_BASE)
-#define INT_730_McBSP1RX_OF	(13 + IH2_BASE)
-#define INT_730_UART_MODEM_IRDA_2 (14 + IH2_BASE)
-#define INT_730_UART_MODEM_1	(15 + IH2_BASE)
-#define INT_730_MCSI		(16 + IH2_BASE)
-#define INT_730_uWireTX		(17 + IH2_BASE)
-#define INT_730_uWireRX		(18 + IH2_BASE)
-#define INT_730_SMC_CD		(19 + IH2_BASE)
-#define INT_730_SMC_IREQ	(20 + IH2_BASE)
-#define INT_730_HDQ_1WIRE	(21 + IH2_BASE)
-#define INT_730_TIMER32K	(22 + IH2_BASE)
-#define INT_730_MMC_SDIO	(23 + IH2_BASE)
-#define INT_730_UPLD		(24 + IH2_BASE)
-#define INT_730_USB_HHC_1	(27 + IH2_BASE)
-#define INT_730_USB_HHC_2	(28 + IH2_BASE)
-#define INT_730_USB_GENI	(29 + IH2_BASE)
-#define INT_730_USB_OTG		(30 + IH2_BASE)
-#define INT_730_CAMERA_IF	(31 + IH2_BASE)
-#define INT_730_RNG		(32 + IH2_BASE)
-#define INT_730_DUAL_MODE_TIMER (33 + IH2_BASE)
-#define INT_730_DBB_RF_EN	(34 + IH2_BASE)
-#define INT_730_MPUIO_KEYPAD	(35 + IH2_BASE)
-#define INT_730_SHA1_MD5	(36 + IH2_BASE)
-#define INT_730_SPI_100K_2	(37 + IH2_BASE)
-#define INT_730_RNG_IDLE	(38 + IH2_BASE)
-#define INT_730_MPUIO		(39 + IH2_BASE)
-#define INT_730_LLPC_LCD_CTRL_CAN_BE_OFF	(40 + IH2_BASE)
-#define INT_730_LLPC_OE_FALLING (41 + IH2_BASE)
-#define INT_730_LLPC_OE_RISING	(42 + IH2_BASE)
-#define INT_730_LLPC_VSYNC	(43 + IH2_BASE)
-#define INT_730_WAKE_UP_REQ	(46 + IH2_BASE)
-#define INT_730_DMA_CH6		(53 + IH2_BASE)
-#define INT_730_DMA_CH7		(54 + IH2_BASE)
-#define INT_730_DMA_CH8		(55 + IH2_BASE)
-#define INT_730_DMA_CH9		(56 + IH2_BASE)
-#define INT_730_DMA_CH10	(57 + IH2_BASE)
-#define INT_730_DMA_CH11	(58 + IH2_BASE)
-#define INT_730_DMA_CH12	(59 + IH2_BASE)
-#define INT_730_DMA_CH13	(60 + IH2_BASE)
-#define INT_730_DMA_CH14	(61 + IH2_BASE)
-#define INT_730_DMA_CH15	(62 + IH2_BASE)
-#define INT_730_NAND		(63 + IH2_BASE)
-
-/*
- * OMAP-850 specific IRQ numbers for interrupt handler 2
+ * OMAP-7xx specific IRQ numbers for interrupt handler 2
  */
-#define INT_850_HW_ERRORS	(0 + IH2_BASE)
-#define INT_850_NFIQ_PWR_FAIL	(1 + IH2_BASE)
-#define INT_850_CFCD		(2 + IH2_BASE)
-#define INT_850_CFIREQ		(3 + IH2_BASE)
-#define INT_850_I2C		(4 + IH2_BASE)
-#define INT_850_PCC		(5 + IH2_BASE)
-#define INT_850_MPU_EXT_NIRQ	(6 + IH2_BASE)
-#define INT_850_SPI_100K_1	(7 + IH2_BASE)
-#define INT_850_SYREN_SPI	(8 + IH2_BASE)
-#define INT_850_VLYNQ		(9 + IH2_BASE)
-#define INT_850_GPIO_BANK4	(10 + IH2_BASE)
-#define INT_850_McBSP1TX	(11 + IH2_BASE)
-#define INT_850_McBSP1RX	(12 + IH2_BASE)
-#define INT_850_McBSP1RX_OF	(13 + IH2_BASE)
-#define INT_850_UART_MODEM_IRDA_2 (14 + IH2_BASE)
-#define INT_850_UART_MODEM_1	(15 + IH2_BASE)
-#define INT_850_MCSI		(16 + IH2_BASE)
-#define INT_850_uWireTX		(17 + IH2_BASE)
-#define INT_850_uWireRX		(18 + IH2_BASE)
-#define INT_850_SMC_CD		(19 + IH2_BASE)
-#define INT_850_SMC_IREQ	(20 + IH2_BASE)
-#define INT_850_HDQ_1WIRE	(21 + IH2_BASE)
-#define INT_850_TIMER32K	(22 + IH2_BASE)
-#define INT_850_MMC_SDIO	(23 + IH2_BASE)
-#define INT_850_UPLD		(24 + IH2_BASE)
-#define INT_850_USB_HHC_1	(27 + IH2_BASE)
-#define INT_850_USB_HHC_2	(28 + IH2_BASE)
-#define INT_850_USB_GENI	(29 + IH2_BASE)
-#define INT_850_USB_OTG		(30 + IH2_BASE)
-#define INT_850_CAMERA_IF	(31 + IH2_BASE)
-#define INT_850_RNG		(32 + IH2_BASE)
-#define INT_850_DUAL_MODE_TIMER (33 + IH2_BASE)
-#define INT_850_DBB_RF_EN	(34 + IH2_BASE)
-#define INT_850_MPUIO_KEYPAD	(35 + IH2_BASE)
-#define INT_850_SHA1_MD5	(36 + IH2_BASE)
-#define INT_850_SPI_100K_2	(37 + IH2_BASE)
-#define INT_850_RNG_IDLE	(38 + IH2_BASE)
-#define INT_850_MPUIO		(39 + IH2_BASE)
-#define INT_850_LLPC_LCD_CTRL_CAN_BE_OFF	(40 + IH2_BASE)
-#define INT_850_LLPC_OE_FALLING (41 + IH2_BASE)
-#define INT_850_LLPC_OE_RISING	(42 + IH2_BASE)
-#define INT_850_LLPC_VSYNC	(43 + IH2_BASE)
-#define INT_850_WAKE_UP_REQ	(46 + IH2_BASE)
-#define INT_850_DMA_CH6		(53 + IH2_BASE)
-#define INT_850_DMA_CH7		(54 + IH2_BASE)
-#define INT_850_DMA_CH8		(55 + IH2_BASE)
-#define INT_850_DMA_CH9		(56 + IH2_BASE)
-#define INT_850_DMA_CH10	(57 + IH2_BASE)
-#define INT_850_DMA_CH11	(58 + IH2_BASE)
-#define INT_850_DMA_CH12	(59 + IH2_BASE)
-#define INT_850_DMA_CH13	(60 + IH2_BASE)
-#define INT_850_DMA_CH14	(61 + IH2_BASE)
-#define INT_850_DMA_CH15	(62 + IH2_BASE)
-#define INT_850_NAND		(63 + IH2_BASE)
+#define INT_7XX_HW_ERRORS	(0 + IH2_BASE)
+#define INT_7XX_NFIQ_PWR_FAIL	(1 + IH2_BASE)
+#define INT_7XX_CFCD		(2 + IH2_BASE)
+#define INT_7XX_CFIREQ		(3 + IH2_BASE)
+#define INT_7XX_I2C		(4 + IH2_BASE)
+#define INT_7XX_PCC		(5 + IH2_BASE)
+#define INT_7XX_MPU_EXT_NIRQ	(6 + IH2_BASE)
+#define INT_7XX_SPI_100K_1	(7 + IH2_BASE)
+#define INT_7XX_SYREN_SPI	(8 + IH2_BASE)
+#define INT_7XX_VLYNQ		(9 + IH2_BASE)
+#define INT_7XX_GPIO_BANK4	(10 + IH2_BASE)
+#define INT_7XX_McBSP1TX	(11 + IH2_BASE)
+#define INT_7XX_McBSP1RX	(12 + IH2_BASE)
+#define INT_7XX_McBSP1RX_OF	(13 + IH2_BASE)
+#define INT_7XX_UART_MODEM_IRDA_2 (14 + IH2_BASE)
+#define INT_7XX_UART_MODEM_1	(15 + IH2_BASE)
+#define INT_7XX_MCSI		(16 + IH2_BASE)
+#define INT_7XX_uWireTX		(17 + IH2_BASE)
+#define INT_7XX_uWireRX		(18 + IH2_BASE)
+#define INT_7XX_SMC_CD		(19 + IH2_BASE)
+#define INT_7XX_SMC_IREQ	(20 + IH2_BASE)
+#define INT_7XX_HDQ_1WIRE	(21 + IH2_BASE)
+#define INT_7XX_TIMER32K	(22 + IH2_BASE)
+#define INT_7XX_MMC_SDIO	(23 + IH2_BASE)
+#define INT_7XX_UPLD		(24 + IH2_BASE)
+#define INT_7XX_USB_HHC_1	(27 + IH2_BASE)
+#define INT_7XX_USB_HHC_2	(28 + IH2_BASE)
+#define INT_7XX_USB_GENI	(29 + IH2_BASE)
+#define INT_7XX_USB_OTG		(30 + IH2_BASE)
+#define INT_7XX_CAMERA_IF	(31 + IH2_BASE)
+#define INT_7XX_RNG		(32 + IH2_BASE)
+#define INT_7XX_DUAL_MODE_TIMER (33 + IH2_BASE)
+#define INT_7XX_DBB_RF_EN	(34 + IH2_BASE)
+#define INT_7XX_MPUIO_KEYPAD	(35 + IH2_BASE)
+#define INT_7XX_SHA1_MD5	(36 + IH2_BASE)
+#define INT_7XX_SPI_100K_2	(37 + IH2_BASE)
+#define INT_7XX_RNG_IDLE	(38 + IH2_BASE)
+#define INT_7XX_MPUIO		(39 + IH2_BASE)
+#define INT_7XX_LLPC_LCD_CTRL_CAN_BE_OFF	(40 + IH2_BASE)
+#define INT_7XX_LLPC_OE_FALLING (41 + IH2_BASE)
+#define INT_7XX_LLPC_OE_RISING	(42 + IH2_BASE)
+#define INT_7XX_LLPC_VSYNC	(43 + IH2_BASE)
+#define INT_7XX_WAKE_UP_REQ	(46 + IH2_BASE)
+#define INT_7XX_DMA_CH6		(53 + IH2_BASE)
+#define INT_7XX_DMA_CH7		(54 + IH2_BASE)
+#define INT_7XX_DMA_CH8		(55 + IH2_BASE)
+#define INT_7XX_DMA_CH9		(56 + IH2_BASE)
+#define INT_7XX_DMA_CH10	(57 + IH2_BASE)
+#define INT_7XX_DMA_CH11	(58 + IH2_BASE)
+#define INT_7XX_DMA_CH12	(59 + IH2_BASE)
+#define INT_7XX_DMA_CH13	(60 + IH2_BASE)
+#define INT_7XX_DMA_CH14	(61 + IH2_BASE)
+#define INT_7XX_DMA_CH15	(62 + IH2_BASE)
+#define INT_7XX_NAND		(63 + IH2_BASE)
 
 #define INT_24XX_SYS_NIRQ	7
 #define INT_24XX_SDMA_IRQ0	12

arch/arm/plat-omap/include/mach/mcbsp.h

@@ -30,8 +30,8 @@
 #include <mach/hardware.h>
 #include <mach/clock.h>
 
-#define OMAP730_MCBSP1_BASE	0xfffb1000
-#define OMAP730_MCBSP2_BASE	0xfffb1800
+#define OMAP7XX_MCBSP1_BASE	0xfffb1000
+#define OMAP7XX_MCBSP2_BASE	0xfffb1800
 
 #define OMAP1510_MCBSP1_BASE	0xe1011800
 #define OMAP1510_MCBSP2_BASE	0xfffb1000
@@ -58,7 +58,7 @@
 #define OMAP44XX_MCBSP3_BASE	0x49026000
 #define OMAP44XX_MCBSP4_BASE	0x48074000
 
-#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP730)
+#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 
 #define OMAP_MCBSP_REG_DRR2	0x00
 #define OMAP_MCBSP_REG_DRR1	0x02

arch/arm/plat-omap/include/mach/mux.h

@@ -51,23 +51,13 @@
 					.pu_pd_reg = PU_PD_SEL_##reg, \
 					.pu_pd_val = status,
 
-#define MUX_REG_730(reg, mode_offset, mode) .mux_reg_name = "OMAP730_IO_CONF_"#reg, \
-					.mux_reg = OMAP730_IO_CONF_##reg, \
+#define MUX_REG_7XX(reg, mode_offset, mode) .mux_reg_name = "OMAP7XX_IO_CONF_"#reg, \
+					.mux_reg = OMAP7XX_IO_CONF_##reg, \
 					.mask_offset = mode_offset, \
 					.mask = mode,
 
-#define PULL_REG_730(reg, bit, status)	.pull_name = "OMAP730_IO_CONF_"#reg, \
-					.pull_reg = OMAP730_IO_CONF_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#define MUX_REG_850(reg, mode_offset, mode) .mux_reg_name = "OMAP850_IO_CONF_"#reg, \
-					.mux_reg = OMAP850_IO_CONF_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG_850(reg, bit, status)	.pull_name = "OMAP850_IO_CONF_"#reg, \
-					.pull_reg = OMAP850_IO_CONF_##reg, \
+#define PULL_REG_7XX(reg, bit, status)	.pull_name = "OMAP7XX_IO_CONF_"#reg, \
+					.pull_reg = OMAP7XX_IO_CONF_##reg, \
 					.pull_bit = bit, \
 					.pull_val = status,
 
@@ -84,21 +74,12 @@
 #define PU_PD_REG(reg, status)		.pu_pd_reg = PU_PD_SEL_##reg, \
 					.pu_pd_val = status,
 
-#define MUX_REG_730(reg, mode_offset, mode) \
-					.mux_reg = OMAP730_IO_CONF_##reg, \
+#define MUX_REG_7XX(reg, mode_offset, mode) \
+					.mux_reg = OMAP7XX_IO_CONF_##reg, \
 					.mask_offset = mode_offset, \
 					.mask = mode,
 
-#define PULL_REG_730(reg, bit, status)	.pull_reg = OMAP730_IO_CONF_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#define MUX_REG_850(reg, mode_offset, mode) \
-					.mux_reg = OMAP850_IO_CONF_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG_850(reg, bit, status)	.pull_reg = OMAP850_IO_CONF_##reg, \
+#define PULL_REG_7XX(reg, bit, status)	.pull_reg = OMAP7XX_IO_CONF_##reg, \
 					.pull_bit = bit, \
 					.pull_val = status,
 
@@ -118,32 +99,21 @@
 
 /*
  * OMAP730/850 has a slightly different config for the pin mux.
- * - config regs are the OMAP730_IO_CONF_x regs (see omap730.h) regs and
+ * - config regs are the OMAP7XX_IO_CONF_x regs (see omap730.h) regs and
  *   not the FUNC_MUX_CTRL_x regs from hardware.h
  * - for pull-up/down, only has one enable bit which is is in the same register
  *   as mux config
  */
-#define MUX_CFG_730(desc, mux_reg, mode_offset, mode,	\
+#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode,	\
 		   pull_bit, pull_status, debug_status)\
 {							\
 	.name =	 desc,					\
 	.debug = debug_status,				\
-	MUX_REG_730(mux_reg, mode_offset, mode)		\
-	PULL_REG_730(mux_reg, pull_bit, pull_status)	\
+	MUX_REG_7XX(mux_reg, mode_offset, mode)		\
+	PULL_REG_7XX(mux_reg, pull_bit, pull_status)	\
 	PU_PD_REG(NA, 0)		\
 },
 
-#define MUX_CFG_850(desc, mux_reg, mode_offset, mode,	\
-		   pull_bit, pull_status, debug_status)\
-{							\
-	.name =	 desc,					\
-	.debug = debug_status,				\
-	MUX_REG_850(mux_reg, mode_offset, mode)		\
-	PULL_REG_850(mux_reg, pull_bit, pull_status)	\
-	PU_PD_REG(NA, 0)		\
-},
-
-
 #define MUX_CFG_24XX(desc, reg_offset, mode,			\
 				pull_en, pull_mode, dbg)	\
 {								\
@@ -232,45 +202,25 @@ struct pin_config {
 
 };
 
-enum omap730_index {
+enum omap7xx_index {
 	/* OMAP 730 keyboard */
-	E2_730_KBR0,
-	J7_730_KBR1,
-	E1_730_KBR2,
-	F3_730_KBR3,
-	D2_730_KBR4,
-	C2_730_KBC0,
-	D3_730_KBC1,
-	E4_730_KBC2,
-	F4_730_KBC3,
-	E3_730_KBC4,
-
-	/* USB */
-	AA17_730_USB_DM,
-	W16_730_USB_PU_EN,
-	W17_730_USB_VBUSI,
-};
-
-enum omap850_index {
-	/* OMAP 850 keyboard */
-	E2_850_KBR0,
-	J7_850_KBR1,
-	E1_850_KBR2,
-	F3_850_KBR3,
-	D2_850_KBR4,
-	C2_850_KBC0,
-	D3_850_KBC1,
-	E4_850_KBC2,
-	F4_850_KBC3,
-	E3_850_KBC4,
+	E2_7XX_KBR0,
+	J7_7XX_KBR1,
+	E1_7XX_KBR2,
+	F3_7XX_KBR3,
+	D2_7XX_KBR4,
+	C2_7XX_KBC0,
+	D3_7XX_KBC1,
+	E4_7XX_KBC2,
+	F4_7XX_KBC3,
+	E3_7XX_KBC4,
 
 	/* USB */
-	AA17_850_USB_DM,
-	W16_850_USB_PU_EN,
-	W17_850_USB_VBUSI,
+	AA17_7XX_USB_DM,
+	W16_7XX_USB_PU_EN,
+	W17_7XX_USB_VBUSI,
 };
 
-
 enum omap1xxx_index {
 	/* UART1 (BT_UART_GATING)*/
 	UART1_TX = 0,

arch/arm/plat-omap/include/mach/omap7xx.h

@@ -0,0 +1,104 @@
+/* arch/arm/plat-omap/include/mach/omap7xx.h
+ *
+ * Hardware definitions for TI OMAP7XX processor.
+ *
+ * Cleanup for Linux-2.6 by Dirk Behme <dirk.behme@de.bosch.com>
+ * Adapted for omap850 by Zebediah C. McClure <zmc@lurian.net>
+ * Adapted for omap7xx by Alistair Buxton <a.j.buxton@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the  GNU General Public License along
+ * with this program; if not, write  to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ASM_ARCH_OMAP7XX_H
+#define __ASM_ARCH_OMAP7XX_H
+
+/*
+ * ----------------------------------------------------------------------------
+ * Base addresses
+ * ----------------------------------------------------------------------------
+ */
+
+/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
+
+#define OMAP7XX_DSP_BASE	0xE0000000
+#define OMAP7XX_DSP_SIZE	0x50000
+#define OMAP7XX_DSP_START	0xE0000000
+
+#define OMAP7XX_DSPREG_BASE	0xE1000000
+#define OMAP7XX_DSPREG_SIZE	SZ_128K
+#define OMAP7XX_DSPREG_START	0xE1000000
+
+/*
+ * ----------------------------------------------------------------------------
+ * OMAP7XX specific configuration registers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP7XX_CONFIG_BASE	0xfffe1000
+#define OMAP7XX_IO_CONF_0	0xfffe1070
+#define OMAP7XX_IO_CONF_1	0xfffe1074
+#define OMAP7XX_IO_CONF_2	0xfffe1078
+#define OMAP7XX_IO_CONF_3	0xfffe107c
+#define OMAP7XX_IO_CONF_4	0xfffe1080
+#define OMAP7XX_IO_CONF_5	0xfffe1084
+#define OMAP7XX_IO_CONF_6	0xfffe1088
+#define OMAP7XX_IO_CONF_7	0xfffe108c
+#define OMAP7XX_IO_CONF_8	0xfffe1090
+#define OMAP7XX_IO_CONF_9	0xfffe1094
+#define OMAP7XX_IO_CONF_10	0xfffe1098
+#define OMAP7XX_IO_CONF_11	0xfffe109c
+#define OMAP7XX_IO_CONF_12	0xfffe10a0
+#define OMAP7XX_IO_CONF_13	0xfffe10a4
+
+#define OMAP7XX_MODE_1		0xfffe1010
+#define OMAP7XX_MODE_2		0xfffe1014
+
+/* CSMI specials: in terms of base + offset */
+#define OMAP7XX_MODE2_OFFSET	0x14
+
+/*
+ * ----------------------------------------------------------------------------
+ * OMAP7XX traffic controller configuration registers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP7XX_FLASH_CFG_0	0xfffecc10
+#define OMAP7XX_FLASH_ACFG_0	0xfffecc50
+#define OMAP7XX_FLASH_CFG_1	0xfffecc14
+#define OMAP7XX_FLASH_ACFG_1	0xfffecc54
+
+/*
+ * ----------------------------------------------------------------------------
+ * OMAP7XX DSP control registers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP7XX_ICR_BASE	0xfffbb800
+#define OMAP7XX_DSP_M_CTL	0xfffbb804
+#define OMAP7XX_DSP_MMU_BASE	0xfffed200
+
+/*
+ * ----------------------------------------------------------------------------
+ * OMAP7XX PCC_UPLD configuration registers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP7XX_PCC_UPLD_CTRL_BASE	(0xfffe0900)
+#define OMAP7XX_PCC_UPLD_CTRL		(OMAP7XX_PCC_UPLD_CTRL_BASE + 0x00)
+
+#endif /*  __ASM_ARCH_OMAP7XX_H */
+

arch/arm/plat-omap/include/mach/uncompress.h

@@ -25,6 +25,7 @@ unsigned int system_rev;
 
 #define UART_OMAP_MDR1		0x08	/* mode definition register */
 #define OMAP_ID_730		0x355F
+#define OMAP_ID_850		0x362C
 #define ID_MASK			0x7fff
 #define check_port(base, shift) ((base[UART_OMAP_MDR1 << shift] & 7) == 0)
 #define omap_get_id() ((*(volatile unsigned int *)(0xfffed404)) >> 12) & ID_MASK
@@ -53,7 +54,7 @@ static void putc(int c)
 		/* MMU is not on, so cpu_is_omapXXXX() won't work here */
 		unsigned int omap_id = omap_get_id();
 
-		if (omap_id == OMAP_ID_730)
+		if (omap_id == OMAP_ID_730 || omap_id == OMAP_ID_850)
 			shift = 0;
 
 		if (check_port(uart, shift))

arch/arm/plat-omap/io.c

@@ -13,7 +13,7 @@
 #include <linux/io.h>
 #include <linux/mm.h>
 
-#include <mach/omap730.h>
+#include <mach/omap7xx.h>
 #include <mach/omap1510.h>
 #include <mach/omap16xx.h>
 #include <mach/omap24xx.h>
@@ -33,13 +33,13 @@ void __iomem *omap_ioremap(unsigned long p, size_t size, unsigned int type)
 		if (BETWEEN(p, OMAP1_IO_PHYS, OMAP1_IO_SIZE))
 			return XLATE(p, OMAP1_IO_PHYS, OMAP1_IO_VIRT);
 	}
-	if (cpu_is_omap730()) {
-		if (BETWEEN(p, OMAP730_DSP_BASE, OMAP730_DSP_SIZE))
-			return XLATE(p, OMAP730_DSP_BASE, OMAP730_DSP_START);
+	if (cpu_is_omap7xx()) {
+		if (BETWEEN(p, OMAP7XX_DSP_BASE, OMAP7XX_DSP_SIZE))
+			return XLATE(p, OMAP7XX_DSP_BASE, OMAP7XX_DSP_START);
 
-		if (BETWEEN(p, OMAP730_DSPREG_BASE, OMAP730_DSPREG_SIZE))
-			return XLATE(p, OMAP730_DSPREG_BASE,
-					OMAP730_DSPREG_START);
+		if (BETWEEN(p, OMAP7XX_DSPREG_BASE, OMAP7XX_DSPREG_SIZE))
+			return XLATE(p, OMAP7XX_DSPREG_BASE,
+					OMAP7XX_DSPREG_START);
 	}
 	if (cpu_is_omap15xx()) {
 		if (BETWEEN(p, OMAP1510_DSP_BASE, OMAP1510_DSP_SIZE))

arch/arm/plat-omap/usb.c

@@ -614,8 +614,8 @@ omap_otg_init(struct omap_usb_config *config)
 	if (config->otg || config->register_host) {
 		syscon &= ~HST_IDLE_EN;
 		ohci_device.dev.platform_data = config;
-		if (cpu_is_omap730())
-			ohci_resources[1].start = INT_730_USB_HHC_1;
+		if (cpu_is_omap7xx())
+			ohci_resources[1].start = INT_7XX_USB_HHC_1;
 		status = platform_device_register(&ohci_device);
 		if (status)
 			pr_debug("can't register OHCI device, %d\n", status);
@@ -626,8 +626,8 @@ omap_otg_init(struct omap_usb_config *config)
 	if (config->otg) {
 		syscon &= ~OTG_IDLE_EN;
 		otg_device.dev.platform_data = config;
-		if (cpu_is_omap730())
-			otg_resources[1].start = INT_730_USB_OTG;
+		if (cpu_is_omap7xx())
+			otg_resources[1].start = INT_7XX_USB_OTG;
 		status = platform_device_register(&otg_device);
 		if (status)
 			pr_debug("can't register OTG device, %d\n", status);
@@ -731,7 +731,7 @@ static inline void omap_1510_usb_init(struct omap_usb_config *config) {}
 
 void __init omap_usb_init(struct omap_usb_config *pdata)
 {
-	if (cpu_is_omap730() || cpu_is_omap16xx() || cpu_is_omap24xx())
+	if (cpu_is_omap7xx() || cpu_is_omap16xx() || cpu_is_omap24xx())
 		omap_otg_init(pdata);
 	else if (cpu_is_omap15xx())
 		omap_1510_usb_init(pdata);

drivers/spi/omap_uwire.c

@@ -52,7 +52,7 @@
 #include <asm/mach-types.h>
 
 #include <mach/mux.h>
-#include <mach/omap730.h>	/* OMAP730_IO_CONF registers */
+#include <mach/omap7xx.h>	/* OMAP7XX_IO_CONF registers */
 
 
 /* FIXME address is now a platform device resource,
@@ -504,7 +504,7 @@ static int __init uwire_probe(struct platform_device *pdev)
 	}
 	clk_enable(uwire->ck);
 
-	if (cpu_is_omap730())
+	if (cpu_is_omap7xx())
 		uwire_idx_shift = 1;
 	else
 		uwire_idx_shift = 2;
@@ -573,8 +573,8 @@ static int __init omap_uwire_init(void)
 	}
 	if (machine_is_omap_perseus2()) {
 		/* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
-		int val = omap_readl(OMAP730_IO_CONF_9) & ~0x00EEE000;
-		omap_writel(val | 0x00AAA000, OMAP730_IO_CONF_9);
+		int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000;
+		omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9);
 	}
 
 	return platform_driver_probe(&uwire_driver, uwire_probe);