Merge branch 'intel'

Jeff Kirsher says:

====================
This series contains updates to e1000e and igb.  Most notably is the
added timestamp support in e1000e and additional software timestamp
support in igb.  As well as, the added thermal data support and SR-IOV
configuration support in igb.

v2- dropped the following patches from the previous 14 patch series
because changes were requested from the community:
  e1000e: add support for IEEE-1588 PTP
  igb: Report L4 Rx hash via skb->l4_rxhash
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/Kconfig

@@ -94,6 +94,8 @@ config IGB
 	tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
 	depends on PCI
 	select PTP_1588_CLOCK
+	select I2C
+	select I2C_ALGOBIT
 	---help---
 	  This driver supports Intel(R) 82575/82576 gigabit ethernet family of
 	  adapters.  For more information on how to identify your adapter, go
@@ -112,6 +114,17 @@ config IGB
 	  To compile this driver as a module, choose M here. The module
 	  will be called igb.
 
+config IGB_HWMON
+	bool "Intel(R) PCI-Express Gigabit adapters HWMON support"
+	default y
+	depends on IGB && HWMON && !(IGB=y && HWMON=m)
+	---help---
+	  Say Y if you want to expose thermal sensor data on Intel devices.
+
+	  Some of our devices contain thermal sensors, both external and internal.
+	  This data is available via the hwmon sysfs interface and exposes
+	  the onboard sensors.
+
 config IGB_DCA
 	bool "Direct Cache Access (DCA) Support"
 	default y

drivers/net/ethernet/intel/e1000e/82571.c

@@ -2044,6 +2044,7 @@ const struct e1000_info e1000_82574_info = {
 				  | FLAG_HAS_MSIX
 				  | FLAG_HAS_JUMBO_FRAMES
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT
@@ -2065,6 +2066,7 @@ const struct e1000_info e1000_82583_info = {
 	.mac			= e1000_82583,
 	.flags			= FLAG_HAS_HW_VLAN_FILTER
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT

drivers/net/ethernet/intel/e1000e/defines.h

@@ -107,6 +107,7 @@
 #define E1000_RXD_ERR_RXE       0x80    /* Rx Data Error */
 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF  /* VLAN ID is in lower 12 bits */
 
+#define E1000_RXDEXT_STATERR_TST   0x00000100	/* Time Stamp taken */
 #define E1000_RXDEXT_STATERR_CE    0x01000000
 #define E1000_RXDEXT_STATERR_SE    0x02000000
 #define E1000_RXDEXT_STATERR_SEQ   0x04000000
@@ -318,6 +319,7 @@
 #define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
 #define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
 #define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
+#define E1000_TXD_EXTCMD_TSTAMP	0x00000010 /* IEEE1588 Timestamp packet */
 
 /* Transmit Control */
 #define E1000_TCTL_EN     0x00000002    /* enable Tx */
@@ -383,6 +385,9 @@
 
 #define E1000_KABGTXD_BGSQLBIAS           0x00050000
 
+/* Low Power IDLE Control */
+#define E1000_LPIC_LPIET_SHIFT		24	/* Low Power Idle Entry Time */
+
 /* PBA constants */
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
@@ -533,6 +538,18 @@
 #define E1000_RXCW_C          0x20000000        /* Receive config */
 #define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
 
+#define E1000_TSYNCTXCTL_VALID		0x00000001 /* Tx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
+#define E1000_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
+
+#define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_ENABLED	0x00000010 /* enable Rx timestamping */
+#define E1000_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
+
+#define E1000_TIMINCA_INCPERIOD_SHIFT	24
+#define E1000_TIMINCA_INCVALUE_MASK	0x00FFFFFF
+
 /* PCI Express Control */
 #define E1000_GCR_RXD_NO_SNOOP          0x00000001
 #define E1000_GCR_RXDSCW_NO_SNOOP       0x00000002
@@ -799,6 +816,33 @@
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 
+/* PHY Low Power Idle Control */
+#define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
+#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
+#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
+
+/* Extended Management Interface (EMI) Registers */
+#define I82579_EMI_ADDR		0x10
+#define I82579_EMI_DATA		0x11
+#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
+#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
+#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_CAPABILITY	0x0410	/* IEEE MMD Register 3.20 */
+#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
+#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
+#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
+#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
+#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
+
+#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
+#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
 
 #define PHY_PAGE_SHIFT 5
 #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \

drivers/net/ethernet/intel/e1000e/e1000.h

@@ -41,6 +41,8 @@
 #include <linux/pci-aspm.h>
 #include <linux/crc32.h>
 #include <linux/if_vlan.h>
+#include <linux/clocksource.h>
+#include <linux/net_tstamp.h>
 
 #include "hw.h"
 
@@ -353,6 +355,7 @@ struct e1000_adapter {
 	u64 gorc_old;
 	u32 alloc_rx_buff_failed;
 	u32 rx_dma_failed;
+	u32 rx_hwtstamp_cleared;
 
 	unsigned int rx_ps_pages;
 	u16 rx_ps_bsize0;
@@ -402,6 +405,14 @@ struct e1000_adapter {
 
 	u16 tx_ring_count;
 	u16 rx_ring_count;
+
+	struct hwtstamp_config hwtstamp_config;
+	struct delayed_work systim_overflow_work;
+	struct sk_buff *tx_hwtstamp_skb;
+	struct work_struct tx_hwtstamp_work;
+	spinlock_t systim_lock;	/* protects SYSTIML/H regsters */
+	struct cyclecounter cc;
+	struct timecounter tc;
 };
 
 struct e1000_info {
@@ -416,6 +427,38 @@ struct e1000_info {
 	const struct e1000_nvm_operations *nvm_ops;
 };
 
+/* The system time is maintained by a 64-bit counter comprised of the 32-bit
+ * SYSTIMH and SYSTIML registers.  How the counter increments (and therefore
+ * its resolution) is based on the contents of the TIMINCA register - it
+ * increments every incperiod (bits 31:24) clock ticks by incvalue (bits 23:0).
+ * For the best accuracy, the incperiod should be as small as possible.  The
+ * incvalue is scaled by a factor as large as possible (while still fitting
+ * in bits 23:0) so that relatively small clock corrections can be made.
+ *
+ * As a result, a shift of INCVALUE_SHIFT_n is used to fit a value of
+ * INCVALUE_n into the TIMINCA register allowing 32+8+(24-INCVALUE_SHIFT_n)
+ * bits to count nanoseconds leaving the rest for fractional nonseconds.
+ */
+#define INCVALUE_96MHz		125
+#define INCVALUE_SHIFT_96MHz	17
+#define INCPERIOD_SHIFT_96MHz	2
+#define INCPERIOD_96MHz		(12 >> INCPERIOD_SHIFT_96MHz)
+
+#define INCVALUE_25MHz		40
+#define INCVALUE_SHIFT_25MHz	18
+#define INCPERIOD_25MHz		1
+
+/* Another drawback of scaling the incvalue by a large factor is the
+ * 64-bit SYSTIM register overflows more quickly.  This is dealt with
+ * by simply reading the clock before it overflows.
+ *
+ * Clock	ns bits	Overflows after
+ * ~~~~~~	~~~~~~~	~~~~~~~~~~~~~~~
+ * 96MHz	47-bit	2^(47-INCPERIOD_SHIFT_96MHz) / 10^9 / 3600 = 9.77 hrs
+ * 25MHz	46-bit	2^46 / 10^9 / 3600 = 19.55 hours
+ */
+#define E1000_SYSTIM_OVERFLOW_PERIOD	(HZ * 60 * 60 * 4)
+
 /* hardware capability, feature, and workaround flags */
 #define FLAG_HAS_AMT                      (1 << 0)
 #define FLAG_HAS_FLASH                    (1 << 1)
@@ -431,7 +474,7 @@ struct e1000_info {
 #define FLAG_HAS_SMART_POWER_DOWN         (1 << 11)
 #define FLAG_IS_QUAD_PORT_A               (1 << 12)
 #define FLAG_IS_QUAD_PORT                 (1 << 13)
-/* reserved bit14 */
+#define FLAG_HAS_HW_TIMESTAMP             (1 << 14)
 #define FLAG_APME_IN_WUC                  (1 << 15)
 #define FLAG_APME_IN_CTRL3                (1 << 16)
 #define FLAG_APME_CHECK_PORT_B            (1 << 17)
@@ -463,6 +506,7 @@ struct e1000_info {
 #define FLAG2_NO_DISABLE_RX               (1 << 10)
 #define FLAG2_PCIM2PCI_ARBITER_WA         (1 << 11)
 #define FLAG2_DFLT_CRC_STRIPPING          (1 << 12)
+#define FLAG2_CHECK_RX_HWTSTAMP           (1 << 13)
 
 #define E1000_RX_DESC_PS(R, i)	    \
 	(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
@@ -659,6 +703,7 @@ extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern bool e1000_check_phy_82574(struct e1000_hw *hw);
+extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {

drivers/net/ethernet/intel/e1000e/ethtool.c

@@ -35,6 +35,7 @@
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/vmalloc.h>
+#include <linux/mdio.h>
 
 #include "e1000.h"
 
@@ -107,6 +108,7 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("dropped_smbus", stats.mgpdc),
 	E1000_STAT("rx_dma_failed", rx_dma_failed),
 	E1000_STAT("tx_dma_failed", tx_dma_failed),
+	E1000_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
 };
 
 #define E1000_GLOBAL_STATS_LEN	ARRAY_SIZE(e1000_gstrings_stats)
@@ -2050,6 +2052,159 @@ static int e1000_get_rxnfc(struct net_device *netdev,
 	}
 }
 
+static int e1000e_get_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	u16 cap_addr, adv_addr, lpa_addr, pcs_stat_addr, phy_data, lpi_ctrl;
+	u32 status, ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	switch (hw->phy.type) {
+	case e1000_phy_82579:
+		cap_addr = I82579_EEE_CAPABILITY;
+		adv_addr = I82579_EEE_ADVERTISEMENT;
+		lpa_addr = I82579_EEE_LP_ABILITY;
+		pcs_stat_addr = I82579_EEE_PCS_STATUS;
+		break;
+	case e1000_phy_i217:
+		cap_addr = I217_EEE_CAPABILITY;
+		adv_addr = I217_EEE_ADVERTISEMENT;
+		lpa_addr = I217_EEE_LP_ABILITY;
+		pcs_stat_addr = I217_EEE_PCS_STATUS;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	ret_val = hw->phy.ops.acquire(hw);
+	if (ret_val)
+		return -EBUSY;
+
+	/* EEE Capability */
+	ret_val = e1000_read_emi_reg_locked(hw, cap_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->supported = mmd_eee_cap_to_ethtool_sup_t(phy_data);
+
+	/* EEE Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, adv_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE Link Partner Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, lpa_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->lp_advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE PCS Status */
+	ret_val = e1000_read_emi_reg_locked(hw, pcs_stat_addr, &phy_data);
+	if (hw->phy.type == e1000_phy_82579)
+		phy_data <<= 8;
+
+release:
+	hw->phy.ops.release(hw);
+	if (ret_val)
+		return -ENODATA;
+
+	e1e_rphy(hw, I82579_LPI_CTRL, &lpi_ctrl);
+	status = er32(STATUS);
+
+	/* Result of the EEE auto negotiation - there is no register that
+	 * has the status of the EEE negotiation so do a best-guess based
+	 * on whether both Tx and Rx LPI indications have been received or
+	 * base it on the link speed, the EEE advertised speeds on both ends
+	 * and the speeds on which EEE is enabled locally.
+	 */
+	if (((phy_data & E1000_EEE_TX_LPI_RCVD) &&
+	     (phy_data & E1000_EEE_RX_LPI_RCVD)) ||
+	    ((status & E1000_STATUS_SPEED_100) &&
+	     (edata->advertised & ADVERTISED_100baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_100baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_100_ENABLE)) ||
+	    ((status & E1000_STATUS_SPEED_1000) &&
+	     (edata->advertised & ADVERTISED_1000baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_1000baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_1000_ENABLE)))
+		edata->eee_active = true;
+
+	edata->eee_enabled = !hw->dev_spec.ich8lan.eee_disable;
+	edata->tx_lpi_enabled = true;
+	edata->tx_lpi_timer = er32(LPIC) >> E1000_LPIC_LPIET_SHIFT;
+
+	return 0;
+}
+
+static int e1000e_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	struct ethtool_eee eee_curr;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	ret_val = e1000e_get_eee(netdev, &eee_curr);
+	if (ret_val)
+		return ret_val;
+
+	if (eee_curr.advertised != edata->advertised) {
+		e_err("Setting EEE advertisement is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_enabled != edata->tx_lpi_enabled) {
+		e_err("Setting EEE tx-lpi is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_timer != edata->tx_lpi_timer) {
+		e_err("Setting EEE Tx LPI timer is not supported\n");
+		return -EINVAL;
+	}
+
+	if (hw->dev_spec.ich8lan.eee_disable != !edata->eee_enabled) {
+		hw->dev_spec.ich8lan.eee_disable = !edata->eee_enabled;
+
+		/* reset the link */
+		if (netif_running(netdev))
+			e1000e_reinit_locked(adapter);
+		else
+			e1000e_reset(adapter);
+	}
+
+	return 0;
+}
+
+static int e1000e_get_ts_info(struct net_device *netdev,
+			      struct ethtool_ts_info *info)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+
+	ethtool_op_get_ts_info(netdev, info);
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return 0;
+
+	info->so_timestamping |= (SOF_TIMESTAMPING_TX_HARDWARE |
+				  SOF_TIMESTAMPING_RX_HARDWARE |
+				  SOF_TIMESTAMPING_RAW_HARDWARE);
+
+	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
+
+	info->rx_filters = ((1 << HWTSTAMP_FILTER_NONE) |
+			    (1 << HWTSTAMP_FILTER_ALL));
+
+	return 0;
+}
+
 static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_settings		= e1000_get_settings,
 	.set_settings		= e1000_set_settings,
@@ -2077,7 +2232,9 @@ static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_coalesce		= e1000_get_coalesce,
 	.set_coalesce		= e1000_set_coalesce,
 	.get_rxnfc		= e1000_get_rxnfc,
-	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_ts_info		= e1000e_get_ts_info,
+	.get_eee		= e1000e_get_eee,
+	.set_eee		= e1000e_set_eee,
 };
 
 void e1000e_set_ethtool_ops(struct net_device *netdev)

drivers/net/ethernet/intel/e1000e/hw.h

@@ -60,8 +60,10 @@ enum e1e_registers {
 	E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
 	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
+	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
 	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
 #define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
+	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
 	E1000_RCTL     = 0x00100, /* Rx Control - RW */
 	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
 	E1000_TXCW     = 0x00178, /* Tx Configuration Word - RW */
@@ -240,6 +242,15 @@ enum e1e_registers {
 #define E1000_PCH_RAICC(_n)	(E1000_PCH_RAICC_BASE + ((_n) * 4))
 #define E1000_CRC_OFFSET	E1000_PCH_RAICC_BASE
 	E1000_HICR      = 0x08F00, /* Host Interface Control */
+	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
+	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
+	E1000_TIMINCA   = 0x0B608, /* Increment attributes register - RW */
+	E1000_TSYNCTXCTL = 0x0B614, /* Tx Time Sync Control register - RW */
+	E1000_TXSTMPL   = 0x0B618, /* Tx timestamp value Low - RO */
+	E1000_TXSTMPH   = 0x0B61C, /* Tx timestamp value High - RO */
+	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
+	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
+	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
 };
 
 #define E1000_MAX_PHY_ADDR		4

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -148,28 +148,6 @@
 #define HV_PM_CTRL		PHY_REG(770, 17)
 #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
 
-/* PHY Low Power Idle Control */
-#define I82579_LPI_CTRL				PHY_REG(772, 20)
-#define I82579_LPI_CTRL_100_ENABLE		0x2000
-#define I82579_LPI_CTRL_1000_ENABLE		0x4000
-#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
-#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
-
-/* Extended Management Interface (EMI) Registers */
-#define I82579_EMI_ADDR         0x10
-#define I82579_EMI_DATA         0x11
-#define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
-#define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
-#define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
-#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
-#define I82579_EEE_LP_ABILITY	0x040F	/* IEEE MMD Register 7.61 */
-#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
-#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
-#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
-#define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
-#define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
-
 /* Intel Rapid Start Technology Support */
 #define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
 #define I217_PROXY_CTRL_AUTO_DISABLE    0x0080
@@ -829,7 +807,7 @@ static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
  *
  *  Assumes the SW/FW/HW Semaphore is already acquired.
  **/
-static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
+s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
 {
 	return __e1000_access_emi_reg_locked(hw, addr, data, true);
 }
@@ -4623,6 +4601,7 @@ const struct e1000_info e1000_pch2_info = {
 	.mac			= e1000_pch2lan,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
@@ -4642,6 +4621,7 @@ const struct e1000_info e1000_pch_lpt_info = {
 	.mac			= e1000_pch_lpt,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -487,21 +487,88 @@ static int e1000_desc_unused(struct e1000_ring *ring)
 	return ring->count + ring->next_to_clean - ring->next_to_use - 1;
 }
 
+/**
+ * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp
+ * @adapter: board private structure
+ * @hwtstamps: time stamp structure to update
+ * @systim: unsigned 64bit system time value.
+ *
+ * Convert the system time value stored in the RX/TXSTMP registers into a
+ * hwtstamp which can be used by the upper level time stamping functions.
+ *
+ * The 'systim_lock' spinlock is used to protect the consistency of the
+ * system time value. This is needed because reading the 64 bit time
+ * value involves reading two 32 bit registers. The first read latches the
+ * value.
+ **/
+static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter,
+				      struct skb_shared_hwtstamps *hwtstamps,
+				      u64 systim)
+{
+	u64 ns;
+	unsigned long flags;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	ns = timecounter_cyc2time(&adapter->tc, systim);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	memset(hwtstamps, 0, sizeof(*hwtstamps));
+	hwtstamps->hwtstamp = ns_to_ktime(ns);
+}
+
+/**
+ * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp
+ * @adapter: board private structure
+ * @status: descriptor extended error and status field
+ * @skb: particular skb to include time stamp
+ *
+ * If the time stamp is valid, convert it into the timecounter ns value
+ * and store that result into the shhwtstamps structure which is passed
+ * up the network stack.
+ **/
+static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status,
+			       struct sk_buff *skb)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u64 rxstmp;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) ||
+	    !(status & E1000_RXDEXT_STATERR_TST) ||
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID))
+		return;
+
+	/* The Rx time stamp registers contain the time stamp.  No other
+	 * received packet will be time stamped until the Rx time stamp
+	 * registers are read.  Because only one packet can be time stamped
+	 * at a time, the register values must belong to this packet and
+	 * therefore none of the other additional attributes need to be
+	 * compared.
+	 */
+	rxstmp = (u64)er32(RXSTMPL);
+	rxstmp |= (u64)er32(RXSTMPH) << 32;
+	e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp);
+
+	adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP;
+}
+
 /**
  * e1000_receive_skb - helper function to handle Rx indications
  * @adapter: board private structure
- * @status: descriptor status field as written by hardware
+ * @staterr: descriptor extended error and status field as written by hardware
  * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
  * @skb: pointer to sk_buff to be indicated to stack
  **/
 static void e1000_receive_skb(struct e1000_adapter *adapter,
 			      struct net_device *netdev, struct sk_buff *skb,
-			      u8 status, __le16 vlan)
+			      u32 staterr, __le16 vlan)
 {
 	u16 tag = le16_to_cpu(vlan);
+
+	e1000e_rx_hwtstamp(adapter, staterr, skb);
+
 	skb->protocol = eth_type_trans(skb, netdev);
 
-	if (status & E1000_RXD_STAT_VP)
+	if (staterr & E1000_RXD_STAT_VP)
 		__vlan_hwaccel_put_tag(skb, tag);
 
 	napi_gro_receive(&adapter->napi, skb);
@@ -1091,6 +1158,41 @@ static void e1000_print_hw_hang(struct work_struct *work)
 		e_err("Try turning off Tx pause (flow control) via ethtool\n");
 }
 
+/**
+ * e1000e_tx_hwtstamp_work - check for Tx time stamp
+ * @work: pointer to work struct
+ *
+ * This work function polls the TSYNCTXCTL valid bit to determine when a
+ * timestamp has been taken for the current stored skb.  The timestamp must
+ * be for this skb because only one such packet is allowed in the queue.
+ */
+static void e1000e_tx_hwtstamp_work(struct work_struct *work)
+{
+	struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
+						     tx_hwtstamp_work);
+	struct e1000_hw *hw = &adapter->hw;
+
+	if (!adapter->tx_hwtstamp_skb)
+		return;
+
+	if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) {
+		struct skb_shared_hwtstamps shhwtstamps;
+		u64 txstmp;
+
+		txstmp = er32(TXSTMPL);
+		txstmp |= (u64)er32(TXSTMPH) << 32;
+
+		e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp);
+
+		skb_tstamp_tx(adapter->tx_hwtstamp_skb, &shhwtstamps);
+		dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+		adapter->tx_hwtstamp_skb = NULL;
+	} else {
+		/* reschedule to check later */
+		schedule_work(&adapter->tx_hwtstamp_work);
+	}
+}
+
 /**
  * e1000_clean_tx_irq - Reclaim resources after transmit completes
  * @tx_ring: Tx descriptor ring
@@ -1345,8 +1447,8 @@ copydone:
 			   cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
 			adapter->rx_hdr_split++;
 
-		e1000_receive_skb(adapter, netdev, skb,
-				  staterr, rx_desc->wb.middle.vlan);
+		e1000_receive_skb(adapter, netdev, skb, staterr,
+				  rx_desc->wb.middle.vlan);
 
 next_desc:
 		rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
@@ -3303,6 +3405,159 @@ static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
 	ew32(MRQC, mrqc);
 }
 
+/**
+ * e1000e_get_base_timinca - get default SYSTIM time increment attributes
+ * @adapter: board private structure
+ * @timinca: pointer to returned time increment attributes
+ *
+ * Get attributes for incrementing the System Time Register SYSTIML/H at
+ * the default base frequency, and set the cyclecounter shift value.
+ **/
+static s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u32 incvalue, incperiod, shift;
+
+	/* Make sure clock is enabled on I217 before checking the frequency */
+	if ((hw->mac.type == e1000_pch_lpt) &&
+	    !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) &&
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) {
+		u32 fextnvm7 = er32(FEXTNVM7);
+
+		if (!(fextnvm7 & (1 << 0))) {
+			ew32(FEXTNVM7, fextnvm7 | (1 << 0));
+			e1e_flush();
+		}
+	}
+
+	switch (hw->mac.type) {
+	case e1000_pch2lan:
+	case e1000_pch_lpt:
+		/* On I217, the clock frequency is 25MHz or 96MHz as
+		 * indicated by the System Clock Frequency Indication
+		 */
+		if ((hw->mac.type != e1000_pch_lpt) ||
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
+			/* Stable 96MHz frequency */
+			incperiod = INCPERIOD_96MHz;
+			incvalue = INCVALUE_96MHz;
+			shift = INCVALUE_SHIFT_96MHz;
+			adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHz;
+			break;
+		}
+		/* fall-through */
+	case e1000_82574:
+	case e1000_82583:
+		/* Stable 25MHz frequency */
+		incperiod = INCPERIOD_25MHz;
+		incvalue = INCVALUE_25MHz;
+		shift = INCVALUE_SHIFT_25MHz;
+		adapter->cc.shift = shift;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) |
+		    ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK));
+
+	return 0;
+}
+
+/**
+ * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable
+ * @adapter: board private structure
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct hwtstamp_config *config = &adapter->hwtstamp_config;
+	u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
+	u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
+	u32 regval;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return -EINVAL;
+
+	/* flags reserved for future extensions - must be zero */
+	if (config->flags)
+		return -EINVAL;
+
+	switch (config->tx_type) {
+	case HWTSTAMP_TX_OFF:
+		tsync_tx_ctl = 0;
+		break;
+	case HWTSTAMP_TX_ON:
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		tsync_rx_ctl = 0;
+		break;
+	case HWTSTAMP_FILTER_ALL:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
+		config->rx_filter = HWTSTAMP_FILTER_ALL;
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	/* enable/disable Tx h/w time stamping */
+	regval = er32(TSYNCTXCTL);
+	regval &= ~E1000_TSYNCTXCTL_ENABLED;
+	regval |= tsync_tx_ctl;
+	ew32(TSYNCTXCTL, regval);
+	if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) !=
+	    (regval & E1000_TSYNCTXCTL_ENABLED)) {
+		e_err("Timesync Tx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* enable/disable Rx h/w time stamping */
+	regval = er32(TSYNCRXCTL);
+	regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK);
+	regval |= tsync_rx_ctl;
+	ew32(TSYNCRXCTL, regval);
+	if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED |
+				 E1000_TSYNCRXCTL_TYPE_MASK)) !=
+	    (regval & (E1000_TSYNCRXCTL_ENABLED |
+		       E1000_TSYNCRXCTL_TYPE_MASK))) {
+		e_err("Timesync Rx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
+	regval = er32(RXSTMPH);
+	regval = er32(TXSTMPH);
+
+	/* Get and set the System Time Register SYSTIM base frequency */
+	ret_val = e1000e_get_base_timinca(adapter, &regval);
+	if (ret_val)
+		return ret_val;
+	ew32(TIMINCA, regval);
+
+	/* reset the ns time counter */
+	timecounter_init(&adapter->tc, &adapter->cc,
+			 ktime_to_ns(ktime_get_real()));
+
+	return 0;
+}
+
 /**
  * e1000_configure - configure the hardware for Rx and Tx
  * @adapter: private board structure
@@ -3529,6 +3784,9 @@ void e1000e_reset(struct e1000_adapter *adapter)
 
 	e1000e_reset_adaptive(hw);
 
+	/* initialize systim and reset the ns time counter */
+	e1000e_config_hwtstamp(adapter);
+
 	if (!netif_running(adapter->netdev) &&
 	    !test_bit(__E1000_TESTING, &adapter->state)) {
 		e1000_power_down_phy(adapter);
@@ -3664,6 +3922,24 @@ void e1000e_reinit_locked(struct e1000_adapter *adapter)
 	clear_bit(__E1000_RESETTING, &adapter->state);
 }
 
+/**
+ * e1000e_cyclecounter_read - read raw cycle counter (used by time counter)
+ * @cc: cyclecounter structure
+ **/
+static cycle_t e1000e_cyclecounter_read(const struct cyclecounter *cc)
+{
+	struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter,
+						     cc);
+	struct e1000_hw *hw = &adapter->hw;
+	cycle_t systim;
+
+	/* latch SYSTIMH on read of SYSTIML */
+	systim = (cycle_t)er32(SYSTIML);
+	systim |= (cycle_t)er32(SYSTIMH) << 32;
+
+	return systim;
+}
+
 /**
  * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
  * @adapter: board private structure to initialize
@@ -3690,6 +3966,17 @@ static int e1000_sw_init(struct e1000_adapter *adapter)
 	if (e1000_alloc_queues(adapter))
 		return -ENOMEM;
 
+	/* Setup hardware time stamping cyclecounter */
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		adapter->cc.read = e1000e_cyclecounter_read;
+		adapter->cc.mask = CLOCKSOURCE_MASK(64);
+		adapter->cc.mult = 1;
+		/* cc.shift set in e1000e_get_base_tininca() */
+
+		spin_lock_init(&adapter->systim_lock);
+		INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work);
+	}
+
 	/* Explicitly disable IRQ since the NIC can be in any state. */
 	e1000_irq_disable(adapter);
 
@@ -4597,6 +4884,17 @@ link_up:
 	if (adapter->flags2 & FLAG2_CHECK_PHY_HANG)
 		e1000e_check_82574_phy_workaround(adapter);
 
+	/* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */
+	if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) {
+		if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) &&
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) {
+			er32(RXSTMPH);
+			adapter->rx_hwtstamp_cleared++;
+		} else {
+			adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP;
+		}
+	}
+
 	/* Reset the timer */
 	if (!test_bit(__E1000_DOWN, &adapter->state))
 		mod_timer(&adapter->watchdog_timer,
@@ -4608,6 +4906,7 @@ link_up:
 #define E1000_TX_FLAGS_TSO		0x00000004
 #define E1000_TX_FLAGS_IPV4		0x00000008
 #define E1000_TX_FLAGS_NO_FCS		0x00000010
+#define E1000_TX_FLAGS_HWTSTAMP		0x00000020
 #define E1000_TX_FLAGS_VLAN_MASK	0xffff0000
 #define E1000_TX_FLAGS_VLAN_SHIFT	16
 
@@ -4866,6 +5165,11 @@ static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
 	if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
 		txd_lower &= ~(E1000_TXD_CMD_IFCS);
 
+	if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) {
+		txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+		txd_upper |= E1000_TXD_EXTCMD_TSTAMP;
+	}
+
 	i = tx_ring->next_to_use;
 
 	do {
@@ -5089,7 +5393,15 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
 	count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit,
 			     nr_frags);
 	if (count) {
-		skb_tx_timestamp(skb);
+		if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
+			     !adapter->tx_hwtstamp_skb)) {
+			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+			tx_flags |= E1000_TX_FLAGS_HWTSTAMP;
+			adapter->tx_hwtstamp_skb = skb_get(skb);
+			schedule_work(&adapter->tx_hwtstamp_work);
+		} else {
+			skb_tx_timestamp(skb);
+		}
 
 		netdev_sent_queue(netdev, skb->len);
 		e1000_tx_queue(tx_ring, tx_flags, count);
@@ -5317,6 +5629,43 @@ static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
 	return 0;
 }
 
+/**
+ * e1000e_hwtstamp_ioctl - control hardware time stamping
+ * @netdev: network interface device structure
+ * @ifreq: interface request
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct hwtstamp_config config;
+	int ret_val;
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+
+	adapter->hwtstamp_config = config;
+
+	ret_val = e1000e_config_hwtstamp(adapter);
+	if (ret_val)
+		return ret_val;
+
+	config = adapter->hwtstamp_config;
+
+	return copy_to_user(ifr->ifr_data, &config,
+			    sizeof(config)) ? -EFAULT : 0;
+}
+
 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 {
 	switch (cmd) {
@@ -5324,6 +5673,8 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 	case SIOCGMIIREG:
 	case SIOCSMIIREG:
 		return e1000_mii_ioctl(netdev, ifr, cmd);
+	case SIOCSHWTSTAMP:
+		return e1000e_hwtstamp_ioctl(netdev, ifr);
 	default:
 		return -EOPNOTSUPP;
 	}
@@ -5548,14 +5899,21 @@ static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
 #else
 static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
 {
+	u16 aspm_ctl = 0;
+
+	if (state & PCIE_LINK_STATE_L0S)
+		aspm_ctl |= PCI_EXP_LNKCTL_ASPM_L0S;
+	if (state & PCIE_LINK_STATE_L1)
+		aspm_ctl |= PCI_EXP_LNKCTL_ASPM_L1;
+
 	/* Both device and parent should have the same ASPM setting.
 	 * Disable ASPM in downstream component first and then upstream.
 	 */
-	pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, state);
+	pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_ctl);
 
 	if (pdev->bus->self)
 		pcie_capability_clear_word(pdev->bus->self, PCI_EXP_LNKCTL,
-					   state);
+					   aspm_ctl);
 }
 #endif
 static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
@@ -6373,6 +6731,14 @@ static void e1000_remove(struct pci_dev *pdev)
 	cancel_work_sync(&adapter->update_phy_task);
 	cancel_work_sync(&adapter->print_hang_task);
 
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		cancel_work_sync(&adapter->tx_hwtstamp_work);
+		if (adapter->tx_hwtstamp_skb) {
+			dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+			adapter->tx_hwtstamp_skb = NULL;
+		}
+	}
+
 	if (!(netdev->flags & IFF_UP))
 		e1000_power_down_phy(adapter);
 

drivers/net/ethernet/intel/igb/Makefile

@@ -34,4 +34,4 @@ obj-$(CONFIG_IGB) += igb.o
 
 igb-objs := igb_main.o igb_ethtool.o e1000_82575.o \
 	    e1000_mac.o e1000_nvm.o e1000_phy.o e1000_mbx.o \
-	    e1000_i210.o igb_ptp.o
+	    e1000_i210.o igb_ptp.o igb_hwmon.o

drivers/net/ethernet/intel/igb/e1000_82575.c

@@ -33,6 +33,7 @@
 
 #include <linux/types.h>
 #include <linux/if_ether.h>
+#include <linux/i2c.h>
 
 #include "e1000_mac.h"
 #include "e1000_82575.h"
@@ -2302,18 +2303,157 @@ out:
 	return ret_val;
 }
 
+static const u8 e1000_emc_temp_data[4] = {
+	E1000_EMC_INTERNAL_DATA,
+	E1000_EMC_DIODE1_DATA,
+	E1000_EMC_DIODE2_DATA,
+	E1000_EMC_DIODE3_DATA
+};
+static const u8 e1000_emc_therm_limit[4] = {
+	E1000_EMC_INTERNAL_THERM_LIMIT,
+	E1000_EMC_DIODE1_THERM_LIMIT,
+	E1000_EMC_DIODE2_THERM_LIMIT,
+	E1000_EMC_DIODE3_THERM_LIMIT
+};
+
+/* igb_get_thermal_sensor_data_generic - Gathers thermal sensor data
+ *  @hw: pointer to hardware structure
+ *
+ *  Updates the temperatures in mac.thermal_sensor_data
+ */
+s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw)
+{
+	s32 status = E1000_SUCCESS;
+	u16 ets_offset;
+	u16 ets_cfg;
+	u16 ets_sensor;
+	u8  num_sensors;
+	u8  sensor_index;
+	u8  sensor_location;
+	u8  i;
+	struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
+
+	if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
+		return E1000_NOT_IMPLEMENTED;
+
+	data->sensor[0].temp = (rd32(E1000_THMJT) & 0xFF);
+
+	/* Return the internal sensor only if ETS is unsupported */
+	hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
+	if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
+		return status;
+
+	hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
+	if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
+	    != NVM_ETS_TYPE_EMC)
+		return E1000_NOT_IMPLEMENTED;
+
+	num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);
+	if (num_sensors > E1000_MAX_SENSORS)
+		num_sensors = E1000_MAX_SENSORS;
+
+	for (i = 1; i < num_sensors; i++) {
+		hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
+		sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
+				NVM_ETS_DATA_INDEX_SHIFT);
+		sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
+				   NVM_ETS_DATA_LOC_SHIFT);
+
+		if (sensor_location != 0)
+			hw->phy.ops.read_i2c_byte(hw,
+					e1000_emc_temp_data[sensor_index],
+					E1000_I2C_THERMAL_SENSOR_ADDR,
+					&data->sensor[i].temp);
+	}
+	return status;
+}
+
+/* igb_init_thermal_sensor_thresh_generic - Sets thermal sensor thresholds
+ *  @hw: pointer to hardware structure
+ *
+ *  Sets the thermal sensor thresholds according to the NVM map
+ *  and save off the threshold and location values into mac.thermal_sensor_data
+ */
+s32 igb_init_thermal_sensor_thresh_generic(struct e1000_hw *hw)
+{
+	s32 status = E1000_SUCCESS;
+	u16 ets_offset;
+	u16 ets_cfg;
+	u16 ets_sensor;
+	u8  low_thresh_delta;
+	u8  num_sensors;
+	u8  sensor_index;
+	u8  sensor_location;
+	u8  therm_limit;
+	u8  i;
+	struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
+
+	if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
+		return E1000_NOT_IMPLEMENTED;
+
+	memset(data, 0, sizeof(struct e1000_thermal_sensor_data));
+
+	data->sensor[0].location = 0x1;
+	data->sensor[0].caution_thresh =
+		(rd32(E1000_THHIGHTC) & 0xFF);
+	data->sensor[0].max_op_thresh =
+		(rd32(E1000_THLOWTC) & 0xFF);
+
+	/* Return the internal sensor only if ETS is unsupported */
+	hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
+	if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
+		return status;
+
+	hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
+	if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
+	    != NVM_ETS_TYPE_EMC)
+		return E1000_NOT_IMPLEMENTED;
+
+	low_thresh_delta = ((ets_cfg & NVM_ETS_LTHRES_DELTA_MASK) >>
+			    NVM_ETS_LTHRES_DELTA_SHIFT);
+	num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);
+
+	for (i = 1; i <= num_sensors; i++) {
+		hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
+		sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
+				NVM_ETS_DATA_INDEX_SHIFT);
+		sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
+				   NVM_ETS_DATA_LOC_SHIFT);
+		therm_limit = ets_sensor & NVM_ETS_DATA_HTHRESH_MASK;
+
+		hw->phy.ops.write_i2c_byte(hw,
+			e1000_emc_therm_limit[sensor_index],
+			E1000_I2C_THERMAL_SENSOR_ADDR,
+			therm_limit);
+
+		if ((i < E1000_MAX_SENSORS) && (sensor_location != 0)) {
+			data->sensor[i].location = sensor_location;
+			data->sensor[i].caution_thresh = therm_limit;
+			data->sensor[i].max_op_thresh = therm_limit -
+							low_thresh_delta;
+		}
+	}
+	return status;
+}
+
 static struct e1000_mac_operations e1000_mac_ops_82575 = {
 	.init_hw              = igb_init_hw_82575,
 	.check_for_link       = igb_check_for_link_82575,
 	.rar_set              = igb_rar_set,
 	.read_mac_addr        = igb_read_mac_addr_82575,
 	.get_speed_and_duplex = igb_get_speed_and_duplex_copper,
+#ifdef CONFIG_IGB_HWMON
+	.get_thermal_sensor_data = igb_get_thermal_sensor_data_generic,
+	.init_thermal_sensor_thresh = igb_init_thermal_sensor_thresh_generic,
+#endif
 };
 
 static struct e1000_phy_operations e1000_phy_ops_82575 = {
 	.acquire              = igb_acquire_phy_82575,
 	.get_cfg_done         = igb_get_cfg_done_82575,
 	.release              = igb_release_phy_82575,
+	.write_i2c_byte       = igb_write_i2c_byte,
+	.read_i2c_byte        = igb_read_i2c_byte,
 };
 
 static struct e1000_nvm_operations e1000_nvm_ops_82575 = {

drivers/net/ethernet/intel/igb/e1000_82575.h

@@ -32,6 +32,10 @@ extern void igb_shutdown_serdes_link_82575(struct e1000_hw *hw);
 extern void igb_power_up_serdes_link_82575(struct e1000_hw *hw);
 extern void igb_power_down_phy_copper_82575(struct e1000_hw *hw);
 extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw);
+extern s32 igb_read_i2c_byte(struct e1000_hw *hw, u8 byte_offset,
+				u8 dev_addr, u8 *data);
+extern s32 igb_write_i2c_byte(struct e1000_hw *hw, u8 byte_offset,
+				 u8 dev_addr, u8 data);
 
 #define ID_LED_DEFAULT_82575_SERDES ((ID_LED_DEF1_DEF2 << 12) | \
                                      (ID_LED_DEF1_DEF2 <<  8) | \
@@ -260,5 +264,16 @@ void igb_vmdq_set_loopback_pf(struct e1000_hw *, bool);
 void igb_vmdq_set_replication_pf(struct e1000_hw *, bool);
 u16 igb_rxpbs_adjust_82580(u32 data);
 s32 igb_set_eee_i350(struct e1000_hw *);
-
+s32 igb_init_thermal_sensor_thresh_generic(struct e1000_hw *);
+s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw);
+
+#define E1000_I2C_THERMAL_SENSOR_ADDR	0xF8
+#define E1000_EMC_INTERNAL_DATA		0x00
+#define E1000_EMC_INTERNAL_THERM_LIMIT	0x20
+#define E1000_EMC_DIODE1_DATA		0x01
+#define E1000_EMC_DIODE1_THERM_LIMIT	0x19
+#define E1000_EMC_DIODE2_DATA		0x23
+#define E1000_EMC_DIODE2_THERM_LIMIT	0x1A
+#define E1000_EMC_DIODE3_DATA		0x2A
+#define E1000_EMC_DIODE3_THERM_LIMIT	0x30
 #endif

drivers/net/ethernet/intel/igb/e1000_defines.h

@@ -470,6 +470,7 @@
 #define E1000_ERR_NO_SPACE          17
 #define E1000_ERR_NVM_PBA_SECTION   18
 #define E1000_ERR_INVM_VALUE_NOT_FOUND	19
+#define E1000_ERR_I2C               20
 
 /* Loop limit on how long we wait for auto-negotiation to complete */
 #define COPPER_LINK_UP_LIMIT              10
@@ -674,6 +675,18 @@
 #define NVM_COMB_VER_SHFT               8
 #define NVM_VER_INVALID            0xFFFF
 #define NVM_ETRACK_SHIFT               16
+#define NVM_ETS_CFG			0x003E
+#define NVM_ETS_LTHRES_DELTA_MASK	0x07C0
+#define NVM_ETS_LTHRES_DELTA_SHIFT	6
+#define NVM_ETS_TYPE_MASK		0x0038
+#define NVM_ETS_TYPE_SHIFT		3
+#define NVM_ETS_TYPE_EMC		0x000
+#define NVM_ETS_NUM_SENSORS_MASK	0x0007
+#define NVM_ETS_DATA_LOC_MASK		0x3C00
+#define NVM_ETS_DATA_LOC_SHIFT		10
+#define NVM_ETS_DATA_INDEX_MASK		0x0300
+#define NVM_ETS_DATA_INDEX_SHIFT	8
+#define NVM_ETS_DATA_HTHRESH_MASK	0x00FF
 
 #define E1000_NVM_CFG_DONE_PORT_0  0x040000 /* MNG config cycle done */
 #define E1000_NVM_CFG_DONE_PORT_1  0x080000 /* ...for second port */

drivers/net/ethernet/intel/igb/e1000_hw.h

@@ -325,6 +325,10 @@ struct e1000_mac_operations {
 	s32  (*get_speed_and_duplex)(struct e1000_hw *, u16 *, u16 *);
 	s32  (*acquire_swfw_sync)(struct e1000_hw *, u16);
 	void (*release_swfw_sync)(struct e1000_hw *, u16);
+#ifdef CONFIG_IGB_HWMON
+	s32 (*get_thermal_sensor_data)(struct e1000_hw *);
+	s32 (*init_thermal_sensor_thresh)(struct e1000_hw *);
+#endif
 
 };
 
@@ -342,6 +346,8 @@ struct e1000_phy_operations {
 	s32  (*set_d0_lplu_state)(struct e1000_hw *, bool);
 	s32  (*set_d3_lplu_state)(struct e1000_hw *, bool);
 	s32  (*write_reg)(struct e1000_hw *, u32, u16);
+	s32 (*read_i2c_byte)(struct e1000_hw *, u8, u8, u8 *);
+	s32 (*write_i2c_byte)(struct e1000_hw *, u8, u8, u8);
 };
 
 struct e1000_nvm_operations {
@@ -354,6 +360,19 @@ struct e1000_nvm_operations {
 	s32  (*valid_led_default)(struct e1000_hw *, u16 *);
 };
 
+#define E1000_MAX_SENSORS		3
+
+struct e1000_thermal_diode_data {
+	u8 location;
+	u8 temp;
+	u8 caution_thresh;
+	u8 max_op_thresh;
+};
+
+struct e1000_thermal_sensor_data {
+	struct e1000_thermal_diode_data sensor[E1000_MAX_SENSORS];
+};
+
 struct e1000_info {
 	s32 (*get_invariants)(struct e1000_hw *);
 	struct e1000_mac_operations *mac_ops;
@@ -399,6 +418,7 @@ struct e1000_mac_info {
 	bool report_tx_early;
 	bool serdes_has_link;
 	bool tx_pkt_filtering;
+	struct e1000_thermal_sensor_data thermal_sensor_data;
 };
 
 struct e1000_phy_info {

drivers/net/ethernet/intel/igb/e1000_regs.h

@@ -75,6 +75,14 @@
 #define E1000_FCRTL    0x02160  /* Flow Control Receive Threshold Low - RW */
 #define E1000_FCRTH    0x02168  /* Flow Control Receive Threshold High - RW */
 #define E1000_FCRTV    0x02460  /* Flow Control Refresh Timer Value - RW */
+#define E1000_I2CPARAMS        0x0102C /* SFPI2C Parameters Register - RW */
+#define E1000_I2CBB_EN      0x00000100  /* I2C - Bit Bang Enable */
+#define E1000_I2C_CLK_OUT   0x00000200  /* I2C- Clock */
+#define E1000_I2C_DATA_OUT  0x00000400  /* I2C- Data Out */
+#define E1000_I2C_DATA_OE_N 0x00000800  /* I2C- Data Output Enable */
+#define E1000_I2C_DATA_IN   0x00001000  /* I2C- Data In */
+#define E1000_I2C_CLK_OE_N  0x00002000  /* I2C- Clock Output Enable */
+#define E1000_I2C_CLK_IN    0x00004000  /* I2C- Clock In */
 
 /* IEEE 1588 TIMESYNCH */
 #define E1000_TSYNCRXCTL 0x0B620 /* Rx Time Sync Control register - RW */
@@ -124,6 +132,14 @@
 
 /* Split and Replication RX Control - RW */
 #define E1000_RXPBS    0x02404  /* Rx Packet Buffer Size - RW */
+
+/* Thermal sensor configuration and status registers */
+#define E1000_THMJT	0x08100 /* Junction Temperature */
+#define E1000_THLOWTC	0x08104 /* Low Threshold Control */
+#define E1000_THMIDTC	0x08108 /* Mid Threshold Control */
+#define E1000_THHIGHTC	0x0810C /* High Threshold Control */
+#define E1000_THSTAT	0x08110 /* Thermal Sensor Status */
+
 /*
  * Convenience macros
  *

drivers/net/ethernet/intel/igb/igb.h

@@ -39,6 +39,8 @@
 #include <linux/ptp_clock_kernel.h>
 #include <linux/bitops.h>
 #include <linux/if_vlan.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
 
 struct igb_adapter;
 
@@ -219,6 +221,7 @@ struct igb_ring {
 		struct igb_tx_buffer *tx_buffer_info;
 		struct igb_rx_buffer *rx_buffer_info;
 	};
+	unsigned long last_rx_timestamp;
 	void *desc;			/* descriptor ring memory */
 	unsigned long flags;		/* ring specific flags */
 	void __iomem *tail;		/* pointer to ring tail register */
@@ -301,6 +304,32 @@ static inline int igb_desc_unused(struct igb_ring *ring)
 	return ring->count + ring->next_to_clean - ring->next_to_use - 1;
 }
 
+struct igb_i2c_client_list {
+	struct i2c_client *client;
+	struct igb_i2c_client_list *next;
+};
+
+#ifdef CONFIG_IGB_HWMON
+
+#define IGB_HWMON_TYPE_LOC	0
+#define IGB_HWMON_TYPE_TEMP	1
+#define IGB_HWMON_TYPE_CAUTION	2
+#define IGB_HWMON_TYPE_MAX	3
+
+struct hwmon_attr {
+	struct device_attribute dev_attr;
+	struct e1000_hw *hw;
+	struct e1000_thermal_diode_data *sensor;
+	char name[12];
+	};
+
+struct hwmon_buff {
+	struct device *device;
+	struct hwmon_attr *hwmon_list;
+	unsigned int n_hwmon;
+	};
+#endif
+
 /* board specific private data structure */
 struct igb_adapter {
 	unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
@@ -386,11 +415,22 @@ struct igb_adapter {
 	struct delayed_work ptp_overflow_work;
 	struct work_struct ptp_tx_work;
 	struct sk_buff *ptp_tx_skb;
+	unsigned long ptp_tx_start;
+	unsigned long last_rx_ptp_check;
 	spinlock_t tmreg_lock;
 	struct cyclecounter cc;
 	struct timecounter tc;
+	u32 tx_hwtstamp_timeouts;
+	u32 rx_hwtstamp_cleared;
 
 	char fw_version[32];
+#ifdef CONFIG_IGB_HWMON
+	struct hwmon_buff igb_hwmon_buff;
+	bool ets;
+#endif
+	struct i2c_algo_bit_data i2c_algo;
+	struct i2c_adapter i2c_adap;
+	struct igb_i2c_client_list *i2c_clients;
 };
 
 #define IGB_FLAG_HAS_MSI		(1 << 0)
@@ -449,6 +489,7 @@ extern void igb_ptp_init(struct igb_adapter *adapter);
 extern void igb_ptp_stop(struct igb_adapter *adapter);
 extern void igb_ptp_reset(struct igb_adapter *adapter);
 extern void igb_ptp_tx_work(struct work_struct *work);
+extern void igb_ptp_rx_hang(struct igb_adapter *adapter);
 extern void igb_ptp_tx_hwtstamp(struct igb_adapter *adapter);
 extern void igb_ptp_rx_rgtstamp(struct igb_q_vector *q_vector,
 				struct sk_buff *skb);
@@ -466,7 +507,10 @@ static inline void igb_ptp_rx_hwtstamp(struct igb_q_vector *q_vector,
 
 extern int igb_ptp_hwtstamp_ioctl(struct net_device *netdev,
 				  struct ifreq *ifr, int cmd);
-
+#ifdef CONFIG_IGB_HWMON
+extern void igb_sysfs_exit(struct igb_adapter *adapter);
+extern int igb_sysfs_init(struct igb_adapter *adapter);
+#endif
 static inline s32 igb_reset_phy(struct e1000_hw *hw)
 {
 	if (hw->phy.ops.reset)

drivers/net/ethernet/intel/igb/igb_ethtool.c

@@ -92,6 +92,8 @@ static const struct igb_stats igb_gstrings_stats[] = {
 	IGB_STAT("os2bmc_tx_by_bmc", stats.b2ospc),
 	IGB_STAT("os2bmc_tx_by_host", stats.o2bspc),
 	IGB_STAT("os2bmc_rx_by_host", stats.b2ogprc),
+	IGB_STAT("tx_hwtstamp_timeouts", tx_hwtstamp_timeouts),
+	IGB_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
 };
 
 #define IGB_NETDEV_STAT(_net_stat) { \
@@ -2272,12 +2274,21 @@ static int igb_get_ts_info(struct net_device *dev,
 	struct igb_adapter *adapter = netdev_priv(dev);
 
 	switch (adapter->hw.mac.type) {
+	case e1000_82575:
+		info->so_timestamping =
+			SOF_TIMESTAMPING_TX_SOFTWARE |
+			SOF_TIMESTAMPING_RX_SOFTWARE |
+			SOF_TIMESTAMPING_SOFTWARE;
+		return 0;
 	case e1000_82576:
 	case e1000_82580:
 	case e1000_i350:
 	case e1000_i210:
 	case e1000_i211:
 		info->so_timestamping =
+			SOF_TIMESTAMPING_TX_SOFTWARE |
+			SOF_TIMESTAMPING_RX_SOFTWARE |
+			SOF_TIMESTAMPING_SOFTWARE |
 			SOF_TIMESTAMPING_TX_HARDWARE |
 			SOF_TIMESTAMPING_RX_HARDWARE |
 			SOF_TIMESTAMPING_RAW_HARDWARE;

drivers/net/ethernet/intel/igb/igb_hwmon.c

@@ -0,0 +1,242 @@
+/*******************************************************************************
+
+  Intel(R) Gigabit Ethernet Linux driver
+  Copyright(c) 2007-2012 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#include "igb.h"
+#include "e1000_82575.h"
+#include "e1000_hw.h"
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/sysfs.h>
+#include <linux/kobject.h>
+#include <linux/device.h>
+#include <linux/netdevice.h>
+#include <linux/hwmon.h>
+#include <linux/pci.h>
+
+#ifdef CONFIG_IGB_HWMON
+/* hwmon callback functions */
+static ssize_t igb_hwmon_show_location(struct device *dev,
+					 struct device_attribute *attr,
+					 char *buf)
+{
+	struct hwmon_attr *igb_attr = container_of(attr, struct hwmon_attr,
+						     dev_attr);
+	return sprintf(buf, "loc%u\n",
+		       igb_attr->sensor->location);
+}
+
+static ssize_t igb_hwmon_show_temp(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct hwmon_attr *igb_attr = container_of(attr, struct hwmon_attr,
+						     dev_attr);
+	unsigned int value;
+
+	/* reset the temp field */
+	igb_attr->hw->mac.ops.get_thermal_sensor_data(igb_attr->hw);
+
+	value = igb_attr->sensor->temp;
+
+	/* display millidegree */
+	value *= 1000;
+
+	return sprintf(buf, "%u\n", value);
+}
+
+static ssize_t igb_hwmon_show_cautionthresh(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct hwmon_attr *igb_attr = container_of(attr, struct hwmon_attr,
+						     dev_attr);
+	unsigned int value = igb_attr->sensor->caution_thresh;
+
+	/* display millidegree */
+	value *= 1000;
+
+	return sprintf(buf, "%u\n", value);
+}
+
+static ssize_t igb_hwmon_show_maxopthresh(struct device *dev,
+				     struct device_attribute *attr,
+				     char *buf)
+{
+	struct hwmon_attr *igb_attr = container_of(attr, struct hwmon_attr,
+						     dev_attr);
+	unsigned int value = igb_attr->sensor->max_op_thresh;
+
+	/* display millidegree */
+	value *= 1000;
+
+	return sprintf(buf, "%u\n", value);
+}
+
+/* igb_add_hwmon_attr - Create hwmon attr table for a hwmon sysfs file.
+ * @ adapter: pointer to the adapter structure
+ * @ offset: offset in the eeprom sensor data table
+ * @ type: type of sensor data to display
+ *
+ * For each file we want in hwmon's sysfs interface we need a device_attribute
+ * This is included in our hwmon_attr struct that contains the references to
+ * the data structures we need to get the data to display.
+ */
+static int igb_add_hwmon_attr(struct igb_adapter *adapter,
+				unsigned int offset, int type) {
+	int rc;
+	unsigned int n_attr;
+	struct hwmon_attr *igb_attr;
+
+	n_attr = adapter->igb_hwmon_buff.n_hwmon;
+	igb_attr = &adapter->igb_hwmon_buff.hwmon_list[n_attr];
+
+	switch (type) {
+	case IGB_HWMON_TYPE_LOC:
+		igb_attr->dev_attr.show = igb_hwmon_show_location;
+		snprintf(igb_attr->name, sizeof(igb_attr->name),
+			 "temp%u_label", offset);
+		break;
+	case IGB_HWMON_TYPE_TEMP:
+		igb_attr->dev_attr.show = igb_hwmon_show_temp;
+		snprintf(igb_attr->name, sizeof(igb_attr->name),
+			 "temp%u_input", offset);
+		break;
+	case IGB_HWMON_TYPE_CAUTION:
+		igb_attr->dev_attr.show = igb_hwmon_show_cautionthresh;
+		snprintf(igb_attr->name, sizeof(igb_attr->name),
+			 "temp%u_max", offset);
+		break;
+	case IGB_HWMON_TYPE_MAX:
+		igb_attr->dev_attr.show = igb_hwmon_show_maxopthresh;
+		snprintf(igb_attr->name, sizeof(igb_attr->name),
+			 "temp%u_crit", offset);
+		break;
+	default:
+		rc = -EPERM;
+		return rc;
+	}
+
+	/* These always the same regardless of type */
+	igb_attr->sensor =
+		&adapter->hw.mac.thermal_sensor_data.sensor[offset];
+	igb_attr->hw = &adapter->hw;
+	igb_attr->dev_attr.store = NULL;
+	igb_attr->dev_attr.attr.mode = S_IRUGO;
+	igb_attr->dev_attr.attr.name = igb_attr->name;
+	sysfs_attr_init(&igb_attr->dev_attr.attr);
+	rc = device_create_file(&adapter->pdev->dev,
+				&igb_attr->dev_attr);
+	if (rc == 0)
+		++adapter->igb_hwmon_buff.n_hwmon;
+
+	return rc;
+}
+
+static void igb_sysfs_del_adapter(struct igb_adapter *adapter)
+{
+	int i;
+
+	if (adapter == NULL)
+		return;
+
+	for (i = 0; i < adapter->igb_hwmon_buff.n_hwmon; i++) {
+		device_remove_file(&adapter->pdev->dev,
+			   &adapter->igb_hwmon_buff.hwmon_list[i].dev_attr);
+	}
+
+	kfree(adapter->igb_hwmon_buff.hwmon_list);
+
+	if (adapter->igb_hwmon_buff.device)
+		hwmon_device_unregister(adapter->igb_hwmon_buff.device);
+}
+
+/* called from igb_main.c */
+void igb_sysfs_exit(struct igb_adapter *adapter)
+{
+	igb_sysfs_del_adapter(adapter);
+}
+
+/* called from igb_main.c */
+int igb_sysfs_init(struct igb_adapter *adapter)
+{
+	struct hwmon_buff *igb_hwmon = &adapter->igb_hwmon_buff;
+	unsigned int i;
+	int n_attrs;
+	int rc = 0;
+
+	/* If this method isn't defined we don't support thermals */
+	if (adapter->hw.mac.ops.init_thermal_sensor_thresh == NULL)
+		goto exit;
+
+	/* Don't create thermal hwmon interface if no sensors present */
+	rc = (adapter->hw.mac.ops.init_thermal_sensor_thresh(&adapter->hw));
+		if (rc)
+			goto exit;
+
+	/* Allocation space for max attributes
+	 * max num sensors * values (loc, temp, max, caution)
+	 */
+	n_attrs = E1000_MAX_SENSORS * 4;
+	igb_hwmon->hwmon_list = kcalloc(n_attrs, sizeof(struct hwmon_attr),
+					  GFP_KERNEL);
+	if (!igb_hwmon->hwmon_list) {
+		rc = -ENOMEM;
+		goto err;
+	}
+
+	igb_hwmon->device = hwmon_device_register(&adapter->pdev->dev);
+	if (IS_ERR(igb_hwmon->device)) {
+		rc = PTR_ERR(igb_hwmon->device);
+		goto err;
+	}
+
+	for (i = 0; i < E1000_MAX_SENSORS; i++) {
+
+		/* Only create hwmon sysfs entries for sensors that have
+		 * meaningful data.
+		 */
+		if (adapter->hw.mac.thermal_sensor_data.sensor[i].location == 0)
+			continue;
+
+		/* Bail if any hwmon attr struct fails to initialize */
+		rc = igb_add_hwmon_attr(adapter, i, IGB_HWMON_TYPE_CAUTION);
+		rc |= igb_add_hwmon_attr(adapter, i, IGB_HWMON_TYPE_LOC);
+		rc |= igb_add_hwmon_attr(adapter, i, IGB_HWMON_TYPE_TEMP);
+		rc |= igb_add_hwmon_attr(adapter, i, IGB_HWMON_TYPE_MAX);
+		if (rc)
+			goto err;
+	}
+
+	goto exit;
+
+err:
+	igb_sysfs_del_adapter(adapter);
+exit:
+	return rc;
+}
+#endif

drivers/net/ethernet/intel/igb/igb_main.c

@@ -57,6 +57,7 @@
 #ifdef CONFIG_IGB_DCA
 #include <linux/dca.h>
 #endif
+#include <linux/i2c.h>
 #include "igb.h"
 
 #define MAJ 4
@@ -193,6 +194,7 @@ static const struct dev_pm_ops igb_pm_ops = {
 };
 #endif
 static void igb_shutdown(struct pci_dev *);
+static int igb_pci_sriov_configure(struct pci_dev *dev, int num_vfs);
 #ifdef CONFIG_IGB_DCA
 static int igb_notify_dca(struct notifier_block *, unsigned long, void *);
 static struct notifier_block dca_notifier = {
@@ -234,6 +236,7 @@ static struct pci_driver igb_driver = {
 	.driver.pm = &igb_pm_ops,
 #endif
 	.shutdown = igb_shutdown,
+	.sriov_configure = igb_pci_sriov_configure,
 	.err_handler = &igb_err_handler
 };
 
@@ -565,6 +568,91 @@ exit:
 	return;
 }
 
+/*  igb_get_i2c_data - Reads the I2C SDA data bit
+ *  @hw: pointer to hardware structure
+ *  @i2cctl: Current value of I2CCTL register
+ *
+ *  Returns the I2C data bit value
+ */
+static int igb_get_i2c_data(void *data)
+{
+	struct igb_adapter *adapter = (struct igb_adapter *)data;
+	struct e1000_hw *hw = &adapter->hw;
+	s32 i2cctl = rd32(E1000_I2CPARAMS);
+
+	return ((i2cctl & E1000_I2C_DATA_IN) != 0);
+}
+
+/* igb_set_i2c_data - Sets the I2C data bit
+ *  @data: pointer to hardware structure
+ *  @state: I2C data value (0 or 1) to set
+ *
+ *  Sets the I2C data bit
+ */
+static void igb_set_i2c_data(void *data, int state)
+{
+	struct igb_adapter *adapter = (struct igb_adapter *)data;
+	struct e1000_hw *hw = &adapter->hw;
+	s32 i2cctl = rd32(E1000_I2CPARAMS);
+
+	if (state)
+		i2cctl |= E1000_I2C_DATA_OUT;
+	else
+		i2cctl &= ~E1000_I2C_DATA_OUT;
+
+	i2cctl &= ~E1000_I2C_DATA_OE_N;
+	i2cctl |= E1000_I2C_CLK_OE_N;
+	wr32(E1000_I2CPARAMS, i2cctl);
+	wrfl();
+
+}
+
+/* igb_set_i2c_clk - Sets the I2C SCL clock
+ *  @data: pointer to hardware structure
+ *  @state: state to set clock
+ *
+ *  Sets the I2C clock line to state
+ */
+static void igb_set_i2c_clk(void *data, int state)
+{
+	struct igb_adapter *adapter = (struct igb_adapter *)data;
+	struct e1000_hw *hw = &adapter->hw;
+	s32 i2cctl = rd32(E1000_I2CPARAMS);
+
+	if (state) {
+		i2cctl |= E1000_I2C_CLK_OUT;
+		i2cctl &= ~E1000_I2C_CLK_OE_N;
+	} else {
+		i2cctl &= ~E1000_I2C_CLK_OUT;
+		i2cctl &= ~E1000_I2C_CLK_OE_N;
+	}
+	wr32(E1000_I2CPARAMS, i2cctl);
+	wrfl();
+}
+
+/* igb_get_i2c_clk - Gets the I2C SCL clock state
+ *  @data: pointer to hardware structure
+ *
+ *  Gets the I2C clock state
+ */
+static int igb_get_i2c_clk(void *data)
+{
+	struct igb_adapter *adapter = (struct igb_adapter *)data;
+	struct e1000_hw *hw = &adapter->hw;
+	s32 i2cctl = rd32(E1000_I2CPARAMS);
+
+	return ((i2cctl & E1000_I2C_CLK_IN) != 0);
+}
+
+static const struct i2c_algo_bit_data igb_i2c_algo = {
+	.setsda		= igb_set_i2c_data,
+	.setscl		= igb_set_i2c_clk,
+	.getsda		= igb_get_i2c_data,
+	.getscl		= igb_get_i2c_clk,
+	.udelay		= 5,
+	.timeout	= 20,
+};
+
 /**
  * igb_get_hw_dev - return device
  * used by hardware layer to print debugging information
@@ -1708,6 +1796,18 @@ void igb_reset(struct igb_adapter *adapter)
 		igb_force_mac_fc(hw);
 
 	igb_init_dmac(adapter, pba);
+#ifdef CONFIG_IGB_HWMON
+	/* Re-initialize the thermal sensor on i350 devices. */
+	if (!test_bit(__IGB_DOWN, &adapter->state)) {
+		if (mac->type == e1000_i350 && hw->bus.func == 0) {
+			/* If present, re-initialize the external thermal sensor
+			 * interface.
+			 */
+			if (adapter->ets)
+				mac->ops.init_thermal_sensor_thresh(hw);
+		}
+	}
+#endif
 	if (!netif_running(adapter->netdev))
 		igb_power_down_link(adapter);
 
@@ -1822,6 +1922,37 @@ void igb_set_fw_version(struct igb_adapter *adapter)
 	return;
 }
 
+static const struct i2c_board_info i350_sensor_info = {
+	I2C_BOARD_INFO("i350bb", 0Xf8),
+};
+
+/*  igb_init_i2c - Init I2C interface
+ *  @adapter: pointer to adapter structure
+ *
+ */
+static s32 igb_init_i2c(struct igb_adapter *adapter)
+{
+	s32 status = E1000_SUCCESS;
+
+	/* I2C interface supported on i350 devices */
+	if (adapter->hw.mac.type != e1000_i350)
+		return E1000_SUCCESS;
+
+	/* Initialize the i2c bus which is controlled by the registers.
+	 * This bus will use the i2c_algo_bit structue that implements
+	 * the protocol through toggling of the 4 bits in the register.
+	 */
+	adapter->i2c_adap.owner = THIS_MODULE;
+	adapter->i2c_algo = igb_i2c_algo;
+	adapter->i2c_algo.data = adapter;
+	adapter->i2c_adap.algo_data = &adapter->i2c_algo;
+	adapter->i2c_adap.dev.parent = &adapter->pdev->dev;
+	strlcpy(adapter->i2c_adap.name, "igb BB",
+		sizeof(adapter->i2c_adap.name));
+	status = i2c_bit_add_bus(&adapter->i2c_adap);
+	return status;
+}
+
 /**
  * igb_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -2114,6 +2245,13 @@ static int igb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	/* reset the hardware with the new settings */
 	igb_reset(adapter);
 
+	/* Init the I2C interface */
+	err = igb_init_i2c(adapter);
+	if (err) {
+		dev_err(&pdev->dev, "failed to init i2c interface\n");
+		goto err_eeprom;
+	}
+
 	/* let the f/w know that the h/w is now under the control of the
 	 * driver. */
 	igb_get_hw_control(adapter);
@@ -2134,7 +2272,27 @@ static int igb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 
 #endif
+#ifdef CONFIG_IGB_HWMON
+	/* Initialize the thermal sensor on i350 devices. */
+	if (hw->mac.type == e1000_i350 && hw->bus.func == 0) {
+		u16 ets_word;
 
+		/*
+		 * Read the NVM to determine if this i350 device supports an
+		 * external thermal sensor.
+		 */
+		hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_word);
+		if (ets_word != 0x0000 && ets_word != 0xFFFF)
+			adapter->ets = true;
+		else
+			adapter->ets = false;
+		if (igb_sysfs_init(adapter))
+			dev_err(&pdev->dev,
+				"failed to allocate sysfs resources\n");
+	} else {
+		adapter->ets = false;
+	}
+#endif
 	/* do hw tstamp init after resetting */
 	igb_ptp_init(adapter);
 
@@ -2175,6 +2333,7 @@ static int igb_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 err_register:
 	igb_release_hw_control(adapter);
+	memset(&adapter->i2c_adap, 0, sizeof(adapter->i2c_adap));
 err_eeprom:
 	if (!igb_check_reset_block(hw))
 		igb_reset_phy(hw);
@@ -2195,6 +2354,111 @@ err_dma:
 	return err;
 }
 
+#ifdef CONFIG_PCI_IOV
+static int  igb_disable_sriov(struct pci_dev *pdev)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct igb_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+
+	/* reclaim resources allocated to VFs */
+	if (adapter->vf_data) {
+		/* disable iov and allow time for transactions to clear */
+		if (igb_vfs_are_assigned(adapter)) {
+			dev_warn(&pdev->dev,
+				 "Cannot deallocate SR-IOV virtual functions while they are assigned - VFs will not be deallocated\n");
+			return -EPERM;
+		} else {
+			pci_disable_sriov(pdev);
+			msleep(500);
+		}
+
+		kfree(adapter->vf_data);
+		adapter->vf_data = NULL;
+		adapter->vfs_allocated_count = 0;
+		wr32(E1000_IOVCTL, E1000_IOVCTL_REUSE_VFQ);
+		wrfl();
+		msleep(100);
+		dev_info(&pdev->dev, "IOV Disabled\n");
+
+		/* Re-enable DMA Coalescing flag since IOV is turned off */
+		adapter->flags |= IGB_FLAG_DMAC;
+	}
+
+	return 0;
+}
+
+static int igb_enable_sriov(struct pci_dev *pdev, int num_vfs)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct igb_adapter *adapter = netdev_priv(netdev);
+	int old_vfs = pci_num_vf(pdev);
+	int err = 0;
+	int i;
+
+	if (!num_vfs)
+		goto out;
+	else if (old_vfs && old_vfs == num_vfs)
+		goto out;
+	else if (old_vfs && old_vfs != num_vfs)
+		err = igb_disable_sriov(pdev);
+
+	if (err)
+		goto out;
+
+	if (num_vfs > 7) {
+		err = -EPERM;
+		goto out;
+	}
+
+	adapter->vfs_allocated_count = num_vfs;
+
+	adapter->vf_data = kcalloc(adapter->vfs_allocated_count,
+				sizeof(struct vf_data_storage), GFP_KERNEL);
+
+	/* if allocation failed then we do not support SR-IOV */
+	if (!adapter->vf_data) {
+		adapter->vfs_allocated_count = 0;
+		dev_err(&pdev->dev,
+			"Unable to allocate memory for VF Data Storage\n");
+		err = -ENOMEM;
+		goto out;
+	}
+
+	err = pci_enable_sriov(pdev, adapter->vfs_allocated_count);
+	if (err)
+		goto err_out;
+
+	dev_info(&pdev->dev, "%d VFs allocated\n",
+		 adapter->vfs_allocated_count);
+	for (i = 0; i < adapter->vfs_allocated_count; i++)
+		igb_vf_configure(adapter, i);
+
+	/* DMA Coalescing is not supported in IOV mode. */
+	adapter->flags &= ~IGB_FLAG_DMAC;
+	goto out;
+
+err_out:
+	kfree(adapter->vf_data);
+	adapter->vf_data = NULL;
+	adapter->vfs_allocated_count = 0;
+out:
+	return err;
+}
+
+#endif
+/*
+ *  igb_remove_i2c - Cleanup  I2C interface
+ *  @adapter: pointer to adapter structure
+ *
+ */
+static void igb_remove_i2c(struct igb_adapter *adapter)
+{
+
+	/* free the adapter bus structure */
+	i2c_del_adapter(&adapter->i2c_adap);
+}
+
 /**
  * igb_remove - Device Removal Routine
  * @pdev: PCI device information struct
@@ -2211,8 +2475,11 @@ static void igb_remove(struct pci_dev *pdev)
 	struct e1000_hw *hw = &adapter->hw;
 
 	pm_runtime_get_noresume(&pdev->dev);
+#ifdef CONFIG_IGB_HWMON
+	igb_sysfs_exit(adapter);
+#endif
+	igb_remove_i2c(adapter);
 	igb_ptp_stop(adapter);
-
 	/*
 	 * The watchdog timer may be rescheduled, so explicitly
 	 * disable watchdog from being rescheduled.
@@ -2242,23 +2509,7 @@ static void igb_remove(struct pci_dev *pdev)
 	igb_clear_interrupt_scheme(adapter);
 
 #ifdef CONFIG_PCI_IOV
-	/* reclaim resources allocated to VFs */
-	if (adapter->vf_data) {
-		/* disable iov and allow time for transactions to clear */
-		if (igb_vfs_are_assigned(adapter)) {
-			dev_info(&pdev->dev, "Unloading driver while VFs are assigned - VFs will not be deallocated\n");
-		} else {
-			pci_disable_sriov(pdev);
-			msleep(500);
-		}
-
-		kfree(adapter->vf_data);
-		adapter->vf_data = NULL;
-		wr32(E1000_IOVCTL, E1000_IOVCTL_REUSE_VFQ);
-		wrfl();
-		msleep(100);
-		dev_info(&pdev->dev, "IOV Disabled\n");
-	}
+	igb_disable_sriov(pdev);
 #endif
 
 	iounmap(hw->hw_addr);
@@ -2289,103 +2540,22 @@ static void igb_probe_vfs(struct igb_adapter *adapter)
 #ifdef CONFIG_PCI_IOV
 	struct pci_dev *pdev = adapter->pdev;
 	struct e1000_hw *hw = &adapter->hw;
-	int old_vfs = pci_num_vf(adapter->pdev);
-	int i;
 
 	/* Virtualization features not supported on i210 family. */
 	if ((hw->mac.type == e1000_i210) || (hw->mac.type == e1000_i211))
 		return;
 
-	if (old_vfs) {
-		dev_info(&pdev->dev, "%d pre-allocated VFs found - override "
-			 "max_vfs setting of %d\n", old_vfs, max_vfs);
-		adapter->vfs_allocated_count = old_vfs;
-	}
-
-	if (!adapter->vfs_allocated_count)
-		return;
-
-	adapter->vf_data = kcalloc(adapter->vfs_allocated_count,
-				sizeof(struct vf_data_storage), GFP_KERNEL);
+	igb_enable_sriov(pdev, max_vfs);
+	pci_sriov_set_totalvfs(pdev, 7);
 
-	/* if allocation failed then we do not support SR-IOV */
-	if (!adapter->vf_data) {
-		adapter->vfs_allocated_count = 0;
-		dev_err(&pdev->dev, "Unable to allocate memory for VF "
-			"Data Storage\n");
-		goto out;
-	}
-
-	if (!old_vfs) {
-		if (pci_enable_sriov(pdev, adapter->vfs_allocated_count))
-			goto err_out;
-	}
-	dev_info(&pdev->dev, "%d VFs allocated\n",
-		 adapter->vfs_allocated_count);
-	for (i = 0; i < adapter->vfs_allocated_count; i++)
-		igb_vf_configure(adapter, i);
-
-	/* DMA Coalescing is not supported in IOV mode. */
-	adapter->flags &= ~IGB_FLAG_DMAC;
-	goto out;
-err_out:
-	kfree(adapter->vf_data);
-	adapter->vf_data = NULL;
-	adapter->vfs_allocated_count = 0;
-out:
-	return;
 #endif /* CONFIG_PCI_IOV */
 }
 
-/**
- * igb_sw_init - Initialize general software structures (struct igb_adapter)
- * @adapter: board private structure to initialize
- *
- * igb_sw_init initializes the Adapter private data structure.
- * Fields are initialized based on PCI device information and
- * OS network device settings (MTU size).
- **/
-static int igb_sw_init(struct igb_adapter *adapter)
+static void igb_init_queue_configuration(struct igb_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
-	struct net_device *netdev = adapter->netdev;
-	struct pci_dev *pdev = adapter->pdev;
 	u32 max_rss_queues;
 
-	pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word);
-
-	/* set default ring sizes */
-	adapter->tx_ring_count = IGB_DEFAULT_TXD;
-	adapter->rx_ring_count = IGB_DEFAULT_RXD;
-
-	/* set default ITR values */
-	adapter->rx_itr_setting = IGB_DEFAULT_ITR;
-	adapter->tx_itr_setting = IGB_DEFAULT_ITR;
-
-	/* set default work limits */
-	adapter->tx_work_limit = IGB_DEFAULT_TX_WORK;
-
-	adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN +
-				  VLAN_HLEN;
-	adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
-
-	spin_lock_init(&adapter->stats64_lock);
-#ifdef CONFIG_PCI_IOV
-	switch (hw->mac.type) {
-	case e1000_82576:
-	case e1000_i350:
-		if (max_vfs > 7) {
-			dev_warn(&pdev->dev,
-				 "Maximum of 7 VFs per PF, using max\n");
-			adapter->vfs_allocated_count = 7;
-		} else
-			adapter->vfs_allocated_count = max_vfs;
-		break;
-	default:
-		break;
-	}
-#endif /* CONFIG_PCI_IOV */
-
 	/* Determine the maximum number of RSS queues supported. */
 	switch (hw->mac.type) {
 	case e1000_i211:
@@ -2444,6 +2614,60 @@ static int igb_sw_init(struct igb_adapter *adapter)
 			adapter->flags |= IGB_FLAG_QUEUE_PAIRS;
 		break;
 	}
+}
+
+/**
+ * igb_sw_init - Initialize general software structures (struct igb_adapter)
+ * @adapter: board private structure to initialize
+ *
+ * igb_sw_init initializes the Adapter private data structure.
+ * Fields are initialized based on PCI device information and
+ * OS network device settings (MTU size).
+ **/
+static int igb_sw_init(struct igb_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct net_device *netdev = adapter->netdev;
+	struct pci_dev *pdev = adapter->pdev;
+
+	pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word);
+
+	/* set default ring sizes */
+	adapter->tx_ring_count = IGB_DEFAULT_TXD;
+	adapter->rx_ring_count = IGB_DEFAULT_RXD;
+
+	/* set default ITR values */
+	adapter->rx_itr_setting = IGB_DEFAULT_ITR;
+	adapter->tx_itr_setting = IGB_DEFAULT_ITR;
+
+	/* set default work limits */
+	adapter->tx_work_limit = IGB_DEFAULT_TX_WORK;
+
+	adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN +
+				  VLAN_HLEN;
+	adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
+
+	spin_lock_init(&adapter->stats64_lock);
+#ifdef CONFIG_PCI_IOV
+	switch (hw->mac.type) {
+	case e1000_82576:
+	case e1000_i350:
+		if (max_vfs > 7) {
+			dev_warn(&pdev->dev,
+				 "Maximum of 7 VFs per PF, using max\n");
+			adapter->vfs_allocated_count = 7;
+		} else
+			adapter->vfs_allocated_count = max_vfs;
+		if (adapter->vfs_allocated_count)
+			dev_warn(&pdev->dev,
+				 "Enabling SR-IOV VFs using the module parameter is deprecated - please use the pci sysfs interface.\n");
+		break;
+	default:
+		break;
+	}
+#endif /* CONFIG_PCI_IOV */
+
+	igb_init_queue_configuration(adapter);
 
 	/* Setup and initialize a copy of the hw vlan table array */
 	adapter->shadow_vfta = kzalloc(sizeof(u32) *
@@ -3767,6 +3991,7 @@ static void igb_watchdog_task(struct work_struct *work)
 	}
 
 	igb_spoof_check(adapter);
+	igb_ptp_rx_hang(adapter);
 
 	/* Reset the timer */
 	if (!test_bit(__IGB_DOWN, &adapter->state))
@@ -4386,12 +4611,15 @@ netdev_tx_t igb_xmit_frame_ring(struct sk_buff *skb,
 	first->bytecount = skb->len;
 	first->gso_segs = 1;
 
+	skb_tx_timestamp(skb);
+
 	if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
 		     !(adapter->ptp_tx_skb))) {
 		skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
 		tx_flags |= IGB_TX_FLAGS_TSTAMP;
 
 		adapter->ptp_tx_skb = skb_get(skb);
+		adapter->ptp_tx_start = jiffies;
 		if (adapter->hw.mac.type == e1000_82576)
 			schedule_work(&adapter->ptp_tx_work);
 	}
@@ -6902,6 +7130,72 @@ static void igb_shutdown(struct pci_dev *pdev)
 	}
 }
 
+#ifdef CONFIG_PCI_IOV
+static int igb_sriov_reinit(struct pci_dev *dev)
+{
+	struct net_device *netdev = pci_get_drvdata(dev);
+	struct igb_adapter *adapter = netdev_priv(netdev);
+	struct pci_dev *pdev = adapter->pdev;
+
+	rtnl_lock();
+
+	if (netif_running(netdev))
+		igb_close(netdev);
+
+	igb_clear_interrupt_scheme(adapter);
+
+	igb_init_queue_configuration(adapter);
+
+	if (igb_init_interrupt_scheme(adapter, true)) {
+		dev_err(&pdev->dev, "Unable to allocate memory for queues\n");
+		return -ENOMEM;
+	}
+
+	if (netif_running(netdev))
+		igb_open(netdev);
+
+	rtnl_unlock();
+
+	return 0;
+}
+
+static int igb_pci_disable_sriov(struct pci_dev *dev)
+{
+	int err = igb_disable_sriov(dev);
+
+	if (!err)
+		err = igb_sriov_reinit(dev);
+
+	return err;
+}
+
+static int igb_pci_enable_sriov(struct pci_dev *dev, int num_vfs)
+{
+	int err = igb_enable_sriov(dev, num_vfs);
+
+	if (err)
+		goto out;
+
+	err = igb_sriov_reinit(dev);
+	if (!err)
+		return num_vfs;
+
+out:
+	return err;
+}
+
+#endif
+static int igb_pci_sriov_configure(struct pci_dev *dev, int num_vfs)
+{
+#ifdef CONFIG_PCI_IOV
+	if (num_vfs == 0)
+		return igb_pci_disable_sriov(dev);
+	else
+		return igb_pci_enable_sriov(dev, num_vfs);
+#endif
+	return 0;
+}
+
 #ifdef CONFIG_NET_POLL_CONTROLLER
 /*
  * Polling 'interrupt' - used by things like netconsole to send skbs
@@ -7307,4 +7601,138 @@ static void igb_init_dmac(struct igb_adapter *adapter, u32 pba)
 	}
 }
 
+static DEFINE_SPINLOCK(i2c_clients_lock);
+
+/*  igb_get_i2c_client - returns matching client
+ *  in adapters's client list.
+ *  @adapter: adapter struct
+ *  @dev_addr: device address of i2c needed.
+ */
+struct i2c_client *
+igb_get_i2c_client(struct igb_adapter *adapter, u8 dev_addr)
+{
+	ulong flags;
+	struct igb_i2c_client_list *client_list;
+	struct i2c_client *client = NULL;
+	struct i2c_board_info client_info = {
+		I2C_BOARD_INFO("igb", 0x00),
+	};
+
+	spin_lock_irqsave(&i2c_clients_lock, flags);
+	client_list = adapter->i2c_clients;
+
+	/* See if we already have an i2c_client */
+	while (client_list) {
+		if (client_list->client->addr == (dev_addr >> 1)) {
+			client = client_list->client;
+			goto exit;
+		} else {
+			client_list = client_list->next;
+		}
+	}
+
+	/* no client_list found, create a new one as long as
+	 * irqs are not disabled
+	 */
+	if (unlikely(irqs_disabled()))
+		goto exit;
+
+	client_list = kzalloc(sizeof(*client_list), GFP_KERNEL);
+	if (client_list == NULL)
+		goto exit;
+
+	/* dev_addr passed to us is left-shifted by 1 bit
+	 * i2c_new_device call expects it to be flush to the right.
+	 */
+	client_info.addr = dev_addr >> 1;
+	client_info.platform_data = adapter;
+	client_list->client = i2c_new_device(&adapter->i2c_adap, &client_info);
+	if (client_list->client == NULL) {
+		dev_info(&adapter->pdev->dev,
+			"Failed to create new i2c device..\n");
+		goto err_no_client;
+	}
+
+	/* insert new client at head of list */
+	client_list->next = adapter->i2c_clients;
+	adapter->i2c_clients = client_list;
+
+	client = client_list->client;
+	goto exit;
+
+err_no_client:
+	kfree(client_list);
+exit:
+	spin_unlock_irqrestore(&i2c_clients_lock, flags);
+	return client;
+}
+
+/*  igb_read_i2c_byte - Reads 8 bit word over I2C
+ *  @hw: pointer to hardware structure
+ *  @byte_offset: byte offset to read
+ *  @dev_addr: device address
+ *  @data: value read
+ *
+ *  Performs byte read operation over I2C interface at
+ *  a specified device address.
+ */
+s32 igb_read_i2c_byte(struct e1000_hw *hw, u8 byte_offset,
+				u8 dev_addr, u8 *data)
+{
+	struct igb_adapter *adapter = container_of(hw, struct igb_adapter, hw);
+	struct i2c_client *this_client = igb_get_i2c_client(adapter, dev_addr);
+	s32 status;
+	u16 swfw_mask = 0;
+
+	if (!this_client)
+		return E1000_ERR_I2C;
+
+	swfw_mask = E1000_SWFW_PHY0_SM;
+
+	if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)
+	    != E1000_SUCCESS)
+		return E1000_ERR_SWFW_SYNC;
+
+	status = i2c_smbus_read_byte_data(this_client, byte_offset);
+	hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+
+	if (status < 0)
+		return E1000_ERR_I2C;
+	else {
+		*data = status;
+		return E1000_SUCCESS;
+	}
+}
+
+/*  igb_write_i2c_byte - Writes 8 bit word over I2C
+ *  @hw: pointer to hardware structure
+ *  @byte_offset: byte offset to write
+ *  @dev_addr: device address
+ *  @data: value to write
+ *
+ *  Performs byte write operation over I2C interface at
+ *  a specified device address.
+ */
+s32 igb_write_i2c_byte(struct e1000_hw *hw, u8 byte_offset,
+				 u8 dev_addr, u8 data)
+{
+	struct igb_adapter *adapter = container_of(hw, struct igb_adapter, hw);
+	struct i2c_client *this_client = igb_get_i2c_client(adapter, dev_addr);
+	s32 status;
+	u16 swfw_mask = E1000_SWFW_PHY0_SM;
+
+	if (!this_client)
+		return E1000_ERR_I2C;
+
+	if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask) != E1000_SUCCESS)
+		return E1000_ERR_SWFW_SYNC;
+	status = i2c_smbus_write_byte_data(this_client, byte_offset, data);
+	hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+
+	if (status)
+		return E1000_ERR_I2C;
+	else
+		return E1000_SUCCESS;
+
+}
 /* igb_main.c */

drivers/net/ethernet/intel/igb/igb_ptp.c

@@ -20,6 +20,7 @@
 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/pci.h>
+#include <linux/ptp_classify.h>
 
 #include "igb.h"
 
@@ -70,6 +71,7 @@
  */
 
 #define IGB_SYSTIM_OVERFLOW_PERIOD	(HZ * 60 * 9)
+#define IGB_PTP_TX_TIMEOUT		(HZ * 15)
 #define INCPERIOD_82576			(1 << E1000_TIMINCA_16NS_SHIFT)
 #define INCVALUE_82576_MASK		((1 << E1000_TIMINCA_16NS_SHIFT) - 1)
 #define INCVALUE_82576			(16 << IGB_82576_TSYNC_SHIFT)
@@ -396,6 +398,15 @@ void igb_ptp_tx_work(struct work_struct *work)
 	if (!adapter->ptp_tx_skb)
 		return;
 
+	if (time_is_before_jiffies(adapter->ptp_tx_start +
+				   IGB_PTP_TX_TIMEOUT)) {
+		dev_kfree_skb_any(adapter->ptp_tx_skb);
+		adapter->ptp_tx_skb = NULL;
+		adapter->tx_hwtstamp_timeouts++;
+		dev_warn(&adapter->pdev->dev, "clearing Tx timestamp hang");
+		return;
+	}
+
 	tsynctxctl = rd32(E1000_TSYNCTXCTL);
 	if (tsynctxctl & E1000_TSYNCTXCTL_VALID)
 		igb_ptp_tx_hwtstamp(adapter);
@@ -418,6 +429,51 @@ static void igb_ptp_overflow_check(struct work_struct *work)
 			      IGB_SYSTIM_OVERFLOW_PERIOD);
 }
 
+/**
+ * igb_ptp_rx_hang - detect error case when Rx timestamp registers latched
+ * @adapter: private network adapter structure
+ *
+ * This watchdog task is scheduled to detect error case where hardware has
+ * dropped an Rx packet that was timestamped when the ring is full. The
+ * particular error is rare but leaves the device in a state unable to timestamp
+ * any future packets.
+ */
+void igb_ptp_rx_hang(struct igb_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct igb_ring *rx_ring;
+	u32 tsyncrxctl = rd32(E1000_TSYNCRXCTL);
+	unsigned long rx_event;
+	int n;
+
+	if (hw->mac.type != e1000_82576)
+		return;
+
+	/* If we don't have a valid timestamp in the registers, just update the
+	 * timeout counter and exit
+	 */
+	if (!(tsyncrxctl & E1000_TSYNCRXCTL_VALID)) {
+		adapter->last_rx_ptp_check = jiffies;
+		return;
+	}
+
+	/* Determine the most recent watchdog or rx_timestamp event */
+	rx_event = adapter->last_rx_ptp_check;
+	for (n = 0; n < adapter->num_rx_queues; n++) {
+		rx_ring = adapter->rx_ring[n];
+		if (time_after(rx_ring->last_rx_timestamp, rx_event))
+			rx_event = rx_ring->last_rx_timestamp;
+	}
+
+	/* Only need to read the high RXSTMP register to clear the lock */
+	if (time_is_before_jiffies(rx_event + 5 * HZ)) {
+		rd32(E1000_RXSTMPH);
+		adapter->last_rx_ptp_check = jiffies;
+		adapter->rx_hwtstamp_cleared++;
+		dev_warn(&adapter->pdev->dev, "clearing Rx timestamp hang");
+	}
+}
+
 /**
  * igb_ptp_tx_hwtstamp - utility function which checks for TX time stamp
  * @adapter: Board private structure.
@@ -643,7 +699,6 @@ int igb_ptp_hwtstamp_ioctl(struct net_device *netdev,
 	else
 		wr32(E1000_ETQF(3), 0);
 
-#define PTP_PORT 319
 	/* L4 Queue Filter[3]: filter by destination port and protocol */
 	if (is_l4) {
 		u32 ftqf = (IPPROTO_UDP /* UDP */
@@ -652,12 +707,12 @@ int igb_ptp_hwtstamp_ioctl(struct net_device *netdev,
 			| E1000_FTQF_MASK); /* mask all inputs */
 		ftqf &= ~E1000_FTQF_MASK_PROTO_BP; /* enable protocol check */
 
-		wr32(E1000_IMIR(3), htons(PTP_PORT));
+		wr32(E1000_IMIR(3), htons(PTP_EV_PORT));
 		wr32(E1000_IMIREXT(3),
 		     (E1000_IMIREXT_SIZE_BP | E1000_IMIREXT_CTRL_BP));
 		if (hw->mac.type == e1000_82576) {
 			/* enable source port check */
-			wr32(E1000_SPQF(3), htons(PTP_PORT));
+			wr32(E1000_SPQF(3), htons(PTP_EV_PORT));
 			ftqf &= ~E1000_FTQF_MASK_SOURCE_PORT_BP;
 		}
 		wr32(E1000_FTQF(3), ftqf);
@@ -801,6 +856,10 @@ void igb_ptp_stop(struct igb_adapter *adapter)
 	}
 
 	cancel_work_sync(&adapter->ptp_tx_work);
+	if (adapter->ptp_tx_skb) {
+		dev_kfree_skb_any(adapter->ptp_tx_skb);
+		adapter->ptp_tx_skb = NULL;
+	}
 
 	if (adapter->ptp_clock) {
 		ptp_clock_unregister(adapter->ptp_clock);