IB/ipath: Remove support for preproduction HTX InfiniPath cards

Clean up some code by removing support for some older pre-production
HTX InfiniPath cards.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>

drivers/infiniband/hw/ipath/ipath_driver.c

@@ -1021,14 +1021,10 @@ void ipath_kreceive(struct ipath_devdata *dd)
 		goto bail;
 	}
 
-	/* There is already a thread processing this queue. */
-	if (test_and_set_bit(0, &dd->ipath_rcv_pending))
-		goto bail;
-
 	l = dd->ipath_port0head;
 	hdrqtail = (u32) le64_to_cpu(*dd->ipath_hdrqtailptr);
 	if (l == hdrqtail)
-		goto done;
+		goto bail;
 
 reloop:
 	for (i = 0; l != hdrqtail; i++) {
@@ -1163,10 +1159,6 @@ reloop:
 	ipath_stats.sps_avgpkts_call =
 		ipath_stats.sps_port0pkts / ++totcalls;
 
-done:
-	clear_bit(0, &dd->ipath_rcv_pending);
-	smp_mb__after_clear_bit();
-
 bail:;
 }
 

drivers/infiniband/hw/ipath/ipath_iba6110.c

@@ -677,6 +677,12 @@ static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
 	if (n)
 		snprintf(name, namelen, "%s", n);
 
+	if (dd->ipath_boardrev != 6 && dd->ipath_boardrev != 7 &&
+	    dd->ipath_boardrev != 11) {
+		ipath_dev_err(dd, "Unsupported InfiniPath board %s!\n", name);
+		ret = 1;
+		goto bail;
+	}
 	if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 ||
 		dd->ipath_minrev > 4)) {
 		/*
@@ -694,36 +700,11 @@ static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
 	 * copies
 	 */
 	dd->ipath_flags |= IPATH_32BITCOUNTERS;
+	dd->ipath_flags |= IPATH_GPIO_INTR;
 	if (dd->ipath_htspeed != 800)
 		ipath_dev_err(dd,
 			      "Incorrectly configured for HT @ %uMHz\n",
 			      dd->ipath_htspeed);
-	if (dd->ipath_boardrev == 7 || dd->ipath_boardrev == 11 ||
-	    dd->ipath_boardrev == 6)
-		dd->ipath_flags |= IPATH_GPIO_INTR;
-	else
-		dd->ipath_flags |= IPATH_POLL_RX_INTR;
-	if (dd->ipath_boardrev == 8) {	/* LS/X-1 */
-		u64 val;
-		val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-		if (val & INFINIPATH_EXTS_SERDESSEL) {
-			/*
-			 * hardware disabled
-			 *
-			 * This means that the chip is hardware disabled,
-			 * and will not be able to bring up the link,
-			 * in any case.  We special case this and abort
-			 * early, to avoid later messages.  We also set
-			 * the DISABLED status bit
-			 */
-			ipath_dbg("Unit %u is hardware-disabled\n",
-				  dd->ipath_unit);
-			*dd->ipath_statusp |= IPATH_STATUS_DISABLED;
-			/* this value is handled differently */
-			ret = 2;
-			goto bail;
-		}
-	}
 	ret = 0;
 
 bail:
@@ -1574,8 +1555,10 @@ static int ipath_ht_early_init(struct ipath_devdata *dd)
 		 * with 128, rather than 112.
 		 */
 		dd->ipath_flags |= IPATH_GPIO_INTR;
-		dd->ipath_flags &= ~IPATH_POLL_RX_INTR;
-	}
+	} else
+		ipath_dev_err(dd, "Unsupported InfiniPath serial "
+			      "number %.16s!\n", dd->ipath_serial);
+
 	return 0;
 }
 

drivers/infiniband/hw/ipath/ipath_kernel.h

@@ -391,9 +391,6 @@ struct ipath_devdata {
 	struct class_device *diag_class_dev;
 	/* timer used to prevent stats overflow, error throttling, etc. */
 	struct timer_list ipath_stats_timer;
-	/* check for stale messages in rcv queue */
-	/* only allow one intr at a time. */
-	unsigned long ipath_rcv_pending;
 	void *ipath_dummy_hdrq;	/* used after port close */
 	dma_addr_t ipath_dummy_hdrq_phys;
 
@@ -740,7 +737,6 @@ int ipath_set_rx_pol_inv(struct ipath_devdata *dd, u8 new_pol_inv);
 		 * are 64bit */
 #define IPATH_32BITCOUNTERS 0x20000
 		/* can miss port0 rx interrupts */
-#define IPATH_POLL_RX_INTR  0x40000
 #define IPATH_DISABLED      0x80000 /* administratively disabled */
 		/* Use GPIO interrupts for new counters */
 #define IPATH_GPIO_ERRINTRS 0x100000

drivers/infiniband/hw/ipath/ipath_verbs.c

@@ -1375,13 +1375,6 @@ static void __verbs_timer(unsigned long arg)
 {
 	struct ipath_devdata *dd = (struct ipath_devdata *) arg;
 
-	/*
-	 * If port 0 receive packet interrupts are not available, or
-	 * can be missed, poll the receive queue
-	 */
-	if (dd->ipath_flags & IPATH_POLL_RX_INTR)
-		ipath_kreceive(dd);
-
 	/* Handle verbs layer timeouts. */
 	ipath_ib_timer(dd->verbs_dev);