Merge branch 'next/cleanup' into samsung/dt

Conflicts:
	arch/arm/mach-exynos/common.c

The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.

Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

MAINTAINERS

@@ -5114,6 +5114,15 @@ L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/devices/phram.c
 
+PICOXCELL SUPPORT
+M:	Jamie Iles <jamie@jamieiles.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+T:	git git://github.com/jamieiles/linux-2.6-ji.git
+S:	Supported
+F:	arch/arm/mach-picoxcell
+F:	drivers/*/picoxcell*
+F:	drivers/*/*/picoxcell*
+
 PIN CONTROL SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained

arch/arm/Kconfig

@@ -658,6 +658,7 @@ config ARCH_PICOXCELL
 	select HAVE_SCHED_CLOCK
 	select HAVE_TCM
 	select NO_IOPORT
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  This enables support for systems based on the Picochip picoXcell
@@ -892,7 +893,6 @@ config ARCH_U300
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
 	select ARCH_REQUIRE_GPIOLIB
-	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 

arch/arm/Kconfig.debug

@@ -100,6 +100,14 @@ choice
 		  Note that the system will appear to hang during boot if there
 		  is nothing connected to read from the DCC.
 
+	config AT91_DEBUG_LL_DBGU0
+		bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+		depends on HAVE_AT91_DBGU0
+
+	config AT91_DEBUG_LL_DBGU1
+		bool "Kernel low-level debugging on 9263, 9g45 and cap9"
+		depends on HAVE_AT91_DBGU1
+
 	config DEBUG_FOOTBRIDGE_COM1
 		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
 		depends on FOOTBRIDGE
@@ -247,6 +255,43 @@ choice
 		  their output to the standard serial port on the RealView
 		  PB1176 platform.
 
+	config DEBUG_MSM_UART1
+		bool "Kernel low-level debugging messages via MSM UART1"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on MSM devices.
+
+	config DEBUG_MSM_UART2
+		bool "Kernel low-level debugging messages via MSM UART2"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the second serial port on MSM devices.
+
+	config DEBUG_MSM_UART3
+		bool "Kernel low-level debugging messages via MSM UART3"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the third serial port on MSM devices.
+
+	config DEBUG_MSM8660_UART
+		bool "Kernel low-level debugging messages via MSM 8660 UART"
+		depends on ARCH_MSM8X60
+		select MSM_HAS_DEBUG_UART_HS
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port on MSM 8660 devices.
+
+	config DEBUG_MSM8960_UART
+		bool "Kernel low-level debugging messages via MSM 8960 UART"
+		depends on ARCH_MSM8960
+		select MSM_HAS_DEBUG_UART_HS
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port on MSM 8960 devices.
+
 endchoice
 
 config EARLY_PRINTK

arch/arm/configs/pcontrol_g20_defconfig

@@ -1,175 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="/opt/arm-2010q1/bin/arm-none-linux-gnueabi-"
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_TREE_PREEMPT_RCU=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_DEFAULT_DEADLINE=y
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9G20=y
-CONFIG_MACH_PCONTROL_G20=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 mem=128M mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) root=/dev/mmcblk0p1 rootwait rw"
-CONFIG_VFP=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_VLAN_8021Q=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHRAM=m
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_EEPROM_AT24=m
-CONFIG_SCSI=m
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=m
-CONFIG_SCSI_MULTI_LUN=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_MACVLAN=m
-CONFIG_TUN=m
-CONFIG_SMSC_PHY=m
-CONFIG_BROADCOM_PHY=m
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MACB=y
-CONFIG_SMSC911X=m
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_MPPE=m
-CONFIG_INPUT_POLLDEV=y
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=m
-CONFIG_KEYBOARD_MATRIX=m
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=m
-CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-# CONFIG_SERIO is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_SERIAL_MAX3100=m
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_R3964=m
-CONFIG_I2C=m
-CONFIG_I2C_CHARDEV=m
-# CONFIG_I2C_HELPER_AUTO is not set
-CONFIG_I2C_GPIO=m
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=m
-CONFIG_SPI_SPIDEV=m
-CONFIG_GPIO_SYSFS=y
-CONFIG_W1=m
-CONFIG_W1_MASTER_GPIO=m
-CONFIG_W1_SLAVE_DS2431=m
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-# CONFIG_MFD_SUPPORT is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=m
-CONFIG_USB_LIBUSUAL=y
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_GADGET=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_ETH=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_USB_G_HID=m
-CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
-CONFIG_MMC_ATMELMCI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_AUXDISPLAY=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV=y
-CONFIG_STAGING=y
-# CONFIG_STAGING_EXCLUDE_BUILD is not set
-CONFIG_IIO=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_CCITT=y

arch/arm/mach-at91/Kconfig

@@ -3,6 +3,12 @@ if ARCH_AT91
 config HAVE_AT91_DATAFLASH_CARD
 	bool
 
+config HAVE_AT91_DBGU0
+	bool
+
+config HAVE_AT91_DBGU1
+	bool
+
 config HAVE_AT91_USART3
 	bool
 
@@ -21,12 +27,14 @@ config ARCH_AT91RM9200
 	bool "AT91RM9200"
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 
 config ARCH_AT91SAM9260
 	bool "AT91SAM9260 or AT91SAM9XE"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
@@ -37,11 +45,13 @@ config ARCH_AT91SAM9261
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
+	select HAVE_AT91_DBGU0
 
 config ARCH_AT91SAM9G10
 	bool "AT91SAM9G10"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_FB_ATMEL
 
 config ARCH_AT91SAM9263
@@ -50,6 +60,7 @@ config ARCH_AT91SAM9263
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
@@ -57,11 +68,13 @@ config ARCH_AT91SAM9RL
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
+	select HAVE_AT91_DBGU0
 
 config ARCH_AT91SAM9G20
 	bool "AT91SAM9G20"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
@@ -74,6 +87,7 @@ config ARCH_AT91SAM9G45
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
@@ -81,6 +95,7 @@ config ARCH_AT91CAP9
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91X40
 	bool "AT91x40"
@@ -510,8 +525,13 @@ config AT91_TIMER_HZ
 choice
 	prompt "Select a UART for early kernel messages"
 
-config AT91_EARLY_DBGU
-	bool "DBGU"
+config AT91_EARLY_DBGU0
+	bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+	depends on HAVE_AT91_DBGU0
+
+config AT91_EARLY_DBGU1
+	bool "DBGU on 9263, 9g45 and cap9"
+	depends on HAVE_AT91_DBGU1
 
 config AT91_EARLY_USART0
 	bool "USART0"

arch/arm/mach-at91/at91cap9.c

@@ -13,7 +13,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -23,11 +22,11 @@
 #include <mach/at91cap9.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -137,7 +136,7 @@ static struct clk pwm_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91CAP9_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -210,6 +209,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
@@ -221,6 +222,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioABCD_clk),
+	CLKDEV_CON_ID("pioB", &pioABCD_clk),
+	CLKDEV_CON_ID("pioC", &pioABCD_clk),
+	CLKDEV_CON_ID("pioD", &pioABCD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -293,23 +298,19 @@ void __init at91cap9_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91cap9_gpio[] = {
+static struct at91_gpio_bank at91cap9_gpio[] __initdata = {
 	{
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOA,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOA,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOB,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOB,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOC,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOC,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOD,
 	}
 };
 
@@ -318,12 +319,6 @@ static void at91cap9_restart(char mode, const char *cmd)
 	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
-static void at91cap9_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91CAP9 processor initialization
  * -------------------------------------------------------------------- */
@@ -333,10 +328,16 @@ static void __init at91cap9_map_io(void)
 	at91_init_sram(0, AT91CAP9_SRAM_BASE, AT91CAP9_SRAM_SIZE);
 }
 
+static void __init at91cap9_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC);
+}
+
 static void __init at91cap9_initialize(void)
 {
 	arm_pm_restart = at91cap9_restart;
-	pm_power_off = at91cap9_poweroff;
 	at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
 
 	/* Register GPIO subsystem */
@@ -394,6 +395,7 @@ static unsigned int at91cap9_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91cap9_soc = {
 	.map_io = at91cap9_map_io,
 	.default_irq_priority = at91cap9_default_irq_priority,
+	.ioremap_registers = at91cap9_ioremap_registers,
 	.register_clocks = at91cap9_register_clocks,
 	.init = at91cap9_initialize,
 };

arch/arm/mach-at91/at91cap9_devices.c

@@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -179,7 +179,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -200,7 +200,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -227,12 +227,12 @@ static struct platform_device at91cap9_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -264,7 +264,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91cap9_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -332,13 +332,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -398,8 +398,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91CAP9_BASE_ECC,
+		.end	= AT91CAP9_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -425,15 +425,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -670,8 +670,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91CAP9_BASE_RTT,
+		.end	= AT91CAP9_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -694,10 +694,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91CAP9_BASE_WDT,
+		.end	= AT91CAP9_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91cap9_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -807,7 +816,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PA9, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -1021,8 +1030,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91CAP9_BASE_DBGU,
+		.end	= AT91CAP9_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91rm9200.c

@@ -23,6 +23,7 @@
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 static struct map_desc at91rm9200_io_desc[] __initdata = {
 	{
@@ -195,6 +196,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -268,23 +273,19 @@ void __init at91rm9200_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91rm9200_gpio[] = {
+static struct at91_gpio_bank at91rm9200_gpio[] __initdata = {
 	{
 		.id		= AT91RM9200_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91RM9200_BASE_PIOA,
 	}, {
 		.id		= AT91RM9200_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91RM9200_BASE_PIOB,
 	}, {
 		.id		= AT91RM9200_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91RM9200_BASE_PIOC,
 	}, {
 		.id		= AT91RM9200_ID_PIOD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioD_clk,
+		.regbase	= AT91RM9200_BASE_PIOD,
 	}
 };
 
@@ -307,6 +308,10 @@ static void __init at91rm9200_map_io(void)
 	iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc));
 }
 
+static void __init at91rm9200_ioremap_registers(void)
+{
+}
+
 static void __init at91rm9200_initialize(void)
 {
 	arm_pm_restart = at91rm9200_restart;
@@ -366,6 +371,7 @@ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91rm9200_soc = {
 	.map_io = at91rm9200_map_io,
 	.default_irq_priority = at91rm9200_default_irq_priority,
+	.ioremap_registers = at91rm9200_ioremap_registers,
 	.register_clocks = at91rm9200_register_clocks,
 	.init = at91rm9200_initialize,
 };

arch/arm/mach-at91/at91rm9200_devices.c

@@ -114,11 +114,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
-	if (data->pullup_pin)
+	if (gpio_is_valid(data->pullup_pin))
 		at91_set_gpio_output(data->pullup_pin, 0);
 
 	udc_data = *data;
@@ -135,7 +135,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -162,12 +162,12 @@ static struct platform_device at91rm9200_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -199,7 +199,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91rm9200_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	);
 
 	/* input/irq */
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
@@ -268,7 +268,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_deglitch(data->det_pin, 1);
 
 	/* outputs, initially off */
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 	at91_set_gpio_output(data->rst_pin, 0);
 
@@ -328,13 +328,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
@@ -665,10 +665,24 @@ static void __init at91_add_device_tc(void) { }
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_RTC,
+		.end	= AT91RM9200_BASE_RTC + SZ_256 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device at91rm9200_rtc_device = {
 	.name		= "at91_rtc",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= rtc_resources,
+	.num_resources	= ARRAY_SIZE(rtc_resources),
 };
 
 static void __init at91_add_device_rtc(void)
@@ -877,8 +891,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91RM9200_BASE_DBGU,
+		.end	= AT91RM9200_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91rm9200_time.c

@@ -32,6 +32,8 @@ static unsigned long last_crtr;
 static u32 irqmask;
 static struct clock_event_device clkevt;
 
+#define RM9200_TIMER_LATCH	((AT91_SLOW_CLOCK + HZ/2) / HZ)
+
 /*
  * The ST_CRTR is updated asynchronously to the master clock ... but
  * the updates as seen by the CPU don't seem to be strictly monotonic.
@@ -74,8 +76,8 @@ static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id)
 	if (sr & AT91_ST_PITS) {
 		u32	crtr = read_CRTR();
 
-		while (((crtr - last_crtr) & AT91_ST_CRTV) >= LATCH) {
-			last_crtr += LATCH;
+		while (((crtr - last_crtr) & AT91_ST_CRTV) >= RM9200_TIMER_LATCH) {
+			last_crtr += RM9200_TIMER_LATCH;
 			clkevt.event_handler(&clkevt);
 		}
 		return IRQ_HANDLED;
@@ -116,7 +118,7 @@ clkevt32k_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	case CLOCK_EVT_MODE_PERIODIC:
 		/* PIT for periodic irqs; fixed rate of 1/HZ */
 		irqmask = AT91_ST_PITS;
-		at91_sys_write(AT91_ST_PIMR, LATCH);
+		at91_sys_write(AT91_ST_PIMR, RM9200_TIMER_LATCH);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
 		/* ALM for oneshot irqs, set by next_event()

arch/arm/mach-at91/at91sam9260.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -21,11 +20,11 @@
 #include <mach/at91sam9260.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -120,7 +119,7 @@ static struct clk ohci_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9260_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -190,6 +189,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
@@ -209,6 +210,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -270,28 +274,19 @@ void __init at91sam9260_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9260_gpio[] = {
+static struct at91_gpio_bank at91sam9260_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9260_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9260_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9260_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9260_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9260_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9260_BASE_PIOC,
 	}
 };
 
-static void at91sam9260_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9260 processor initialization
  * -------------------------------------------------------------------- */
@@ -325,10 +320,16 @@ static void __init at91sam9260_map_io(void)
 	}
 }
 
+static void __init at91sam9260_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
+}
+
 static void __init at91sam9260_initialize(void)
 {
 	arm_pm_restart = at91sam9_alt_restart;
-	pm_power_off = at91sam9260_poweroff;
 	at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
 			| (1 << AT91SAM9260_ID_IRQ2);
 
@@ -381,6 +382,7 @@ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9260_soc = {
 	.map_io = at91sam9260_map_io,
 	.default_irq_priority = at91sam9260_default_irq_priority,
+	.ioremap_registers = at91sam9260_ioremap_registers,
 	.register_clocks = at91sam9260_register_clocks,
 	.init = at91sam9260_initialize,
 };

arch/arm/mach-at91/at91sam9260_devices.c

@@ -115,7 +115,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -136,7 +136,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -163,12 +163,12 @@ static struct platform_device at91sam9260_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -200,7 +200,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9260_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -243,13 +243,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -330,11 +330,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
 		if (data->slot[i].bus_width) {
 			/* input/irq */
-			if (data->slot[i].detect_pin) {
+			if (gpio_is_valid(data->slot[i].detect_pin)) {
 				at91_set_gpio_input(data->slot[i].detect_pin, 1);
 				at91_set_deglitch(data->slot[i].detect_pin, 1);
 			}
-			if (data->slot[i].wp_pin)
+			if (gpio_is_valid(data->slot[i].wp_pin))
 				at91_set_gpio_input(data->slot[i].wp_pin, 1);
 
 			switch (i) {
@@ -399,8 +399,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9260_BASE_ECC,
+		.end	= AT91SAM9260_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -426,15 +426,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -714,8 +714,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9260_BASE_RTT,
+		.end	= AT91SAM9260_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -738,10 +738,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9260_BASE_WDT,
+		.end	= AT91SAM9260_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9260_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -837,8 +846,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9260_BASE_DBGU,
+		.end	= AT91SAM9260_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -1281,17 +1290,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 
 	at91_sys_write(AT91_MATRIX_EBICSA, csa);
 
-	if (data->rst_pin) {
+	if (gpio_is_valid(data->rst_pin)) {
 		at91_set_multi_drive(data->rst_pin, 0);
 		at91_set_gpio_output(data->rst_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 0);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 0);
 		at91_set_deglitch(data->det_pin, 1);
 	}

arch/arm/mach-at91/at91sam9261.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -20,11 +19,11 @@
 #include <mach/at91sam9261.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -176,6 +175,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -251,28 +253,19 @@ void __init at91sam9261_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9261_gpio[] = {
+static struct at91_gpio_bank at91sam9261_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9261_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9261_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9261_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9261_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9261_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9261_BASE_PIOC,
 	}
 };
 
-static void at91sam9261_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9261 processor initialization
  * -------------------------------------------------------------------- */
@@ -285,10 +278,16 @@ static void __init at91sam9261_map_io(void)
 		at91_init_sram(0, AT91SAM9261_SRAM_BASE, AT91SAM9261_SRAM_SIZE);
 }
 
+static void __init at91sam9261_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
+}
+
 static void __init at91sam9261_initialize(void)
 {
 	arm_pm_restart = at91sam9_alt_restart;
-	pm_power_off = at91sam9261_poweroff;
 	at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
 			| (1 << AT91SAM9261_ID_IRQ2);
 
@@ -341,6 +340,7 @@ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9261_soc = {
 	.map_io = at91sam9261_map_io,
 	.default_irq_priority = at91sam9261_default_irq_priority,
+	.ioremap_registers = at91sam9261_ioremap_registers,
 	.register_clocks = at91sam9261_register_clocks,
 	.init = at91sam9261_initialize,
 };

arch/arm/mach-at91/at91sam9261_devices.c

@@ -118,7 +118,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -171,13 +171,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -240,15 +240,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */
@@ -600,8 +600,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9261_BASE_RTT,
+		.end	= AT91SAM9261_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -624,10 +624,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9261_BASE_WDT,
+		.end	= AT91SAM9261_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9261_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -816,8 +825,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9261_BASE_DBGU,
+		.end	= AT91SAM9261_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam9263.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -19,11 +18,11 @@
 #include <mach/at91sam9263.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -118,7 +117,7 @@ static struct clk pwm_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9263_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -182,6 +181,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
@@ -191,6 +192,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioCDE_clk),
+	CLKDEV_CON_ID("pioD", &pioCDE_clk),
+	CLKDEV_CON_ID("pioE", &pioCDE_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -263,36 +269,25 @@ void __init at91sam9263_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9263_gpio[] = {
+static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9263_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9263_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9263_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9263_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOC,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOD,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOD,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOE,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOE,
 	}
 };
 
-static void at91sam9263_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9263 processor initialization
  * -------------------------------------------------------------------- */
@@ -303,10 +298,17 @@ static void __init at91sam9263_map_io(void)
 	at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
 }
 
+static void __init at91sam9263_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
+	at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
+}
+
 static void __init at91sam9263_initialize(void)
 {
 	arm_pm_restart = at91sam9_alt_restart;
-	pm_power_off = at91sam9263_poweroff;
 	at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
 
 	/* Register GPIO subsystem */
@@ -358,6 +360,7 @@ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9263_soc = {
 	.map_io = at91sam9263_map_io,
 	.default_irq_priority = at91sam9263_default_irq_priority,
+	.ioremap_registers = at91sam9263_ioremap_registers,
 	.register_clocks = at91sam9263_register_clocks,
 	.init = at91sam9263_initialize,
 };

arch/arm/mach-at91/at91sam9263_devices.c

@@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -123,7 +123,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -144,7 +144,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -171,12 +171,12 @@ static struct platform_device at91sam9263_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -208,7 +208,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9263_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -276,13 +276,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -430,17 +430,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	}
 	at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		/* initially off */
 		at91_set_gpio_output(data->vcc_pin, 0);
 
@@ -473,8 +473,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC0,
-		.end	= AT91_BASE_SYS + AT91_ECC0 + SZ_512 - 1,
+		.start	= AT91SAM9263_BASE_ECC0,
+		.end	= AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -500,15 +500,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -749,7 +749,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -956,8 +956,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt0_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT0,
-		.end	= AT91_BASE_SYS + AT91_RTT0 + SZ_16 - 1,
+		.start	= AT91SAM9263_BASE_RTT0,
+		.end	= AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -971,8 +971,8 @@ static struct platform_device at91sam9263_rtt0_device = {
 
 static struct resource rtt1_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT1,
-		.end	= AT91_BASE_SYS + AT91_RTT1 + SZ_16 - 1,
+		.start	= AT91SAM9263_BASE_RTT1,
+		.end	= AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -996,10 +996,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9263_BASE_WDT,
+		.end	= AT91SAM9263_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9263_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -1196,8 +1205,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9263_BASE_DBGU,
+		.end	= AT91SAM9263_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam926x_time.c

@@ -25,7 +25,17 @@
 
 static u32 pit_cycle;		/* write-once */
 static u32 pit_cnt;		/* access only w/system irq blocked */
+static void __iomem *pit_base_addr __read_mostly;
 
+static inline unsigned int pit_read(unsigned int reg_offset)
+{
+	return __raw_readl(pit_base_addr + reg_offset);
+}
+
+static inline void pit_write(unsigned int reg_offset, unsigned long value)
+{
+	__raw_writel(value, pit_base_addr + reg_offset);
+}
 
 /*
  * Clocksource:  just a monotonic counter of MCK/16 cycles.
@@ -39,7 +49,7 @@ static cycle_t read_pit_clk(struct clocksource *cs)
 
 	raw_local_irq_save(flags);
 	elapsed = pit_cnt;
-	t = at91_sys_read(AT91_PIT_PIIR);
+	t = pit_read(AT91_PIT_PIIR);
 	raw_local_irq_restore(flags);
 
 	elapsed += PIT_PICNT(t) * pit_cycle;
@@ -64,8 +74,8 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
 		/* update clocksource counter */
-		pit_cnt += pit_cycle * PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
-		at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
+		pit_cnt += pit_cycle * PIT_PICNT(pit_read(AT91_PIT_PIVR));
+		pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
 				| AT91_PIT_PITIEN);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
@@ -74,7 +84,7 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	case CLOCK_EVT_MODE_SHUTDOWN:
 	case CLOCK_EVT_MODE_UNUSED:
 		/* disable irq, leaving the clocksource active */
-		at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+		pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
 		break;
 	case CLOCK_EVT_MODE_RESUME:
 		break;
@@ -103,11 +113,11 @@ static irqreturn_t at91sam926x_pit_interrupt(int irq, void *dev_id)
 
 	/* The PIT interrupt may be disabled, and is shared */
 	if ((pit_clkevt.mode == CLOCK_EVT_MODE_PERIODIC)
-			&& (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
+			&& (pit_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
 		unsigned nr_ticks;
 
 		/* Get number of ticks performed before irq, and ack it */
-		nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
+		nr_ticks = PIT_PICNT(pit_read(AT91_PIT_PIVR));
 		do {
 			pit_cnt += pit_cycle;
 			pit_clkevt.event_handler(&pit_clkevt);
@@ -129,14 +139,14 @@ static struct irqaction at91sam926x_pit_irq = {
 static void at91sam926x_pit_reset(void)
 {
 	/* Disable timer and irqs */
-	at91_sys_write(AT91_PIT_MR, 0);
+	pit_write(AT91_PIT_MR, 0);
 
 	/* Clear any pending interrupts, wait for PIT to stop counting */
-	while (PIT_CPIV(at91_sys_read(AT91_PIT_PIVR)) != 0)
+	while (PIT_CPIV(pit_read(AT91_PIT_PIVR)) != 0)
 		cpu_relax();
 
 	/* Start PIT but don't enable IRQ */
-	at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+	pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
 }
 
 /*
@@ -178,7 +188,15 @@ static void __init at91sam926x_pit_init(void)
 static void at91sam926x_pit_suspend(void)
 {
 	/* Disable timer */
-	at91_sys_write(AT91_PIT_MR, 0);
+	pit_write(AT91_PIT_MR, 0);
+}
+
+void __init at91sam926x_ioremap_pit(u32 addr)
+{
+	pit_base_addr = ioremap(addr, 16);
+
+	if (!pit_base_addr)
+		panic("Impossible to ioremap PIT\n");
 }
 
 struct sys_timer at91sam926x_timer = {

arch/arm/mach-at91/at91sam9g45.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 #include <linux/dma-mapping.h>
 
 #include <asm/irq.h>
@@ -20,12 +19,12 @@
 #include <mach/at91sam9g45.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 #include <mach/cpu.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -150,7 +149,7 @@ static struct clk ac97_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9G45_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -209,6 +208,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	/* One additional fake clock for ohci */
 	CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk),
@@ -231,6 +232,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "fff98000.serial", &usart3_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioDE_clk),
+	CLKDEV_CON_ID("pioE", &pioDE_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -293,27 +299,22 @@ void __init at91sam9g45_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9g45_gpio[] = {
+static struct at91_gpio_bank at91sam9g45_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9G45_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOD,
-		.clock		= &pioDE_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOD,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOE,
-		.clock		= &pioDE_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOE,
 	}
 };
 
@@ -322,12 +323,6 @@ static void at91sam9g45_restart(char mode, const char *cmd)
 	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
-static void at91sam9g45_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9G45 processor initialization
  * -------------------------------------------------------------------- */
@@ -338,10 +333,16 @@ static void __init at91sam9g45_map_io(void)
 	init_consistent_dma_size(SZ_4M);
 }
 
+static void __init at91sam9g45_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
+}
+
 static void __init at91sam9g45_initialize(void)
 {
 	arm_pm_restart = at91sam9g45_restart;
-	pm_power_off = at91sam9g45_poweroff;
 	at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
 
 	/* Register GPIO subsystem */
@@ -393,6 +394,7 @@ static unsigned int at91sam9g45_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9g45_soc = {
 	.map_io = at91sam9g45_map_io,
 	.default_irq_priority = at91sam9g45_default_irq_priority,
+	.ioremap_registers = at91sam9g45_ioremap_registers,
 	.register_clocks = at91sam9g45_register_clocks,
 	.init = at91sam9g45_initialize,
 };

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -44,8 +44,8 @@ static struct at_dma_platform_data atdma_pdata = {
 
 static struct resource hdmac_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DMA,
-		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_DMA,
+		.end	= AT91SAM9G45_BASE_DMA + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -181,7 +181,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -263,7 +263,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -284,7 +284,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -311,12 +311,12 @@ static struct platform_device at91sam9g45_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -348,7 +348,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9g45_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -449,11 +449,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 
 
 	/* input/irq */
-	if (data->slot[0].detect_pin) {
+	if (gpio_is_valid(data->slot[0].detect_pin)) {
 		at91_set_gpio_input(data->slot[0].detect_pin, 1);
 		at91_set_deglitch(data->slot[0].detect_pin, 1);
 	}
-	if (data->slot[0].wp_pin)
+	if (gpio_is_valid(data->slot[0].wp_pin))
 		at91_set_gpio_input(data->slot[0].wp_pin, 1);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -529,8 +529,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_ECC,
+		.end	= AT91SAM9G45_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -556,15 +556,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -859,7 +859,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD6, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -1009,10 +1009,24 @@ static void __init at91_add_device_tc(void) { }
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_RTC,
+		.end	= AT91SAM9G45_BASE_RTC + SZ_256 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device at91sam9g45_rtc_device = {
 	.name		= "at91_rtc",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= rtc_resources,
+	.num_resources	= ARRAY_SIZE(rtc_resources),
 };
 
 static void __init at91_add_device_rtc(void)
@@ -1081,8 +1095,8 @@ void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {}
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9G45_BASE_RTT,
+		.end	= AT91SAM9G45_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -1133,10 +1147,19 @@ static void __init at91_add_device_trng(void) {}
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9G45_BASE_WDT,
+		.end	= AT91SAM9G45_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9g45_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -1332,8 +1355,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_DBGU,
+		.end	= AT91SAM9G45_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam9rl.c

@@ -10,7 +10,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -20,11 +19,11 @@
 #include <mach/at91sam9rl.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -184,6 +183,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -243,32 +246,22 @@ void __init at91sam9rl_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9rl_gpio[] = {
+static struct at91_gpio_bank at91sam9rl_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9RL_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioD_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOD,
 	}
 };
 
-static void at91sam9rl_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9RL processor initialization
  * -------------------------------------------------------------------- */
@@ -290,10 +283,16 @@ static void __init at91sam9rl_map_io(void)
 	at91_init_sram(0, AT91SAM9RL_SRAM_BASE, sram_size);
 }
 
+static void __init at91sam9rl_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
+}
+
 static void __init at91sam9rl_initialize(void)
 {
 	arm_pm_restart = at91sam9_alt_restart;
-	pm_power_off = at91sam9rl_poweroff;
 	at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
 
 	/* Register GPIO subsystem */
@@ -345,6 +344,7 @@ static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9rl_soc = {
 	.map_io = at91sam9rl_map_io,
 	.default_irq_priority = at91sam9rl_default_irq_priority,
+	.ioremap_registers = at91sam9rl_ioremap_registers,
 	.register_clocks = at91sam9rl_register_clocks,
 	.init = at91sam9rl_initialize,
 };

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -39,8 +39,8 @@ static struct at_dma_platform_data atdma_pdata = {
 
 static struct resource hdmac_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DMA,
-		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_DMA,
+		.end	= AT91SAM9RL_BASE_DMA + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[2] = {
@@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -248,8 +248,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_ECC,
+		.end	= AT91SAM9RL_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */
@@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD4, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -685,8 +685,8 @@ static void __init at91_add_device_rtc(void) {}
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9RL_BASE_RTT,
+		.end	= AT91SAM9RL_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -709,10 +709,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9RL_BASE_WDT,
+		.end	= AT91SAM9RL_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9rl_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -908,8 +917,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_DBGU,
+		.end	= AT91SAM9RL_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/board-1arm.c

@@ -63,13 +63,15 @@ static void __init onearm_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata onearm_eth_data = {
+static struct macb_platform_data __initdata onearm_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata onearm_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata onearm_udc_data = {

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -75,6 +75,8 @@ static void __init afeb9260_init_early(void)
  */
 static struct at91_usbh_data __initdata afeb9260_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
  */
 static struct at91_udc_data __initdata afeb9260_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -103,7 +105,7 @@ static struct spi_board_info afeb9260_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata afeb9260_macb_data = {
+static struct macb_platform_data __initdata afeb9260_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA9,
 	.is_rmii	= 0,
 };
@@ -138,6 +140,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 	.bus_width_16	= 0,
 	.parts		= afeb9260_nand_partition,
 	.num_parts	= ARRAY_SIZE(afeb9260_nand_partition),
+	.det_pin	= -EINVAL,
 };
 
 
@@ -149,6 +152,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 	.wp_pin 	= AT91_PIN_PC4,
 	.slot_b		= 1,
 	.wire4		= 1,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -169,6 +173,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 static struct at91_cf_data afeb9260_cf_data = {
 	.chipselect = 4,
 	.irq_pin    = AT91_PIN_PA6,
+	.det_pin	= -EINVAL,
+	.vcc_pin	= -EINVAL,
 	.rst_pin    = AT91_PIN_PA7,
 	.flags      = AT91_CF_TRUE_IDE,
 };

arch/arm/mach-at91/board-cam60.c

@@ -62,6 +62,8 @@ static void __init cam60_init_early(void)
  */
 static struct at91_usbh_data __initdata cam60_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -115,7 +117,7 @@ static struct spi_board_info cam60_spi_devices[] __initdata = {
 /*
  * MACB Ethernet device
  */
-static struct __initdata at91_eth_data cam60_macb_data = {
+static struct __initdata macb_platform_data cam60_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PB5,
 	.is_rmii	= 0,
 };
@@ -135,7 +137,7 @@ static struct mtd_partition __initdata cam60_nand_partition[] = {
 static struct atmel_nand_data __initdata cam60_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA9,
 	.enable_pin	= AT91_PIN_PA7,
 	.parts		= cam60_nand_partition,
@@ -163,7 +165,7 @@ static struct sam9_smc_config __initdata cam60_nand_smc_config = {
 static void __init cam60_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &cam60_nand_smc_config);
+	sam9_smc_configure(0, 3, &cam60_nand_smc_config);
 
 	at91_add_device_nand(&cam60_nand_data);
 }

arch/arm/mach-at91/board-cap9adk.c

@@ -70,6 +70,8 @@ static void __init cap9adk_init_early(void)
  */
 static struct at91_usbh_data __initdata cap9adk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -144,16 +146,17 @@ static struct spi_board_info cap9adk_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata cap9adk_mmc_data = {
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata cap9adk_macb_data = {
+static struct macb_platform_data __initdata cap9adk_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -172,8 +175,8 @@ static struct mtd_partition __initdata cap9adk_nand_partitions[] = {
 static struct atmel_nand_data __initdata cap9adk_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
-//	.rdy_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.rdy_pin	= -EINVAL,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= cap9adk_nand_partitions,
 	.num_parts	= ARRAY_SIZE(cap9adk_nand_partitions),
@@ -212,7 +215,7 @@ static void __init cap9adk_add_device_nand(void)
 		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &cap9adk_nand_smc_config);
+	sam9_smc_configure(0, 3, &cap9adk_nand_smc_config);
 
 	at91_add_device_nand(&cap9adk_nand_data);
 }
@@ -282,7 +285,7 @@ static __init void cap9adk_add_device_nor(void)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
 
 	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, &cap9adk_nor_smc_config);
+	sam9_smc_configure(0, 0, &cap9adk_nor_smc_config);
 
 	platform_device_register(&cap9adk_nor_flash);
 }
@@ -351,7 +354,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
  * AC97
  */
 static struct ac97c_platform_data cap9adk_ac97_data = {
-//	.reset_pin	= ... not connected
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-carmeva.c

@@ -57,13 +57,15 @@ static void __init carmeva_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata carmeva_eth_data = {
+static struct macb_platform_data __initdata carmeva_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata carmeva_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata carmeva_udc_data = {
@@ -75,8 +77,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 // static struct at91_cf_data __initdata carmeva_cf_data = {
 //	.det_pin	= AT91_PIN_PB0,
 //	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
+	// .irq_pin	= -EINVAL,
+	// .vcc_pin	= -EINVAL,
 // };
 
 static struct at91_mmc_data __initdata carmeva_mmc_data = {
@@ -84,6 +86,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PB10,
 	.wp_pin		= AT91_PIN_PC14,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {

arch/arm/mach-at91/board-cpu9krea.c

@@ -86,6 +86,8 @@ static void __init cpu9krea_init_early(void)
  */
 static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,13 +95,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
  */
 static struct at91_udc_data __initdata cpu9krea_udc_data = {
 	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata cpu9krea_macb_data = {
+static struct macb_platform_data __initdata cpu9krea_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -112,6 +115,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 #ifdef CONFIG_MACH_CPU9260
@@ -156,7 +160,7 @@ static struct sam9_smc_config __initdata cpu9krea_nand_smc_config = {
 
 static void __init cpu9krea_add_device_nand(void)
 {
-	sam9_smc_configure(3, &cpu9krea_nand_smc_config);
+	sam9_smc_configure(0, 3, &cpu9krea_nand_smc_config);
 	at91_add_device_nand(&cpu9krea_nand_data);
 }
 
@@ -238,7 +242,7 @@ static __init void cpu9krea_add_device_nor(void)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
 
 	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, &cpu9krea_nor_smc_config);
+	sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config);
 
 	platform_device_register(&cpu9krea_nor_flash);
 }
@@ -337,6 +341,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA29,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init cpu9krea_board_init(void)

arch/arm/mach-at91/board-cpuat91.c

@@ -82,12 +82,15 @@ static void __init cpuat91_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata cpuat91_eth_data = {
+static struct macb_platform_data __initdata cpuat91_eth_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata cpuat91_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata cpuat91_udc_data = {
@@ -98,6 +101,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 static struct at91_mmc_data __initdata cpuat91_mmc_data = {
 	.det_pin	= AT91_PIN_PC2,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {

arch/arm/mach-at91/board-csb337.c

@@ -58,18 +58,20 @@ static void __init csb337_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata csb337_eth_data = {
+static struct macb_platform_data __initdata csb337_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC2,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata csb337_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb337_udc_data = {
-	// this has no VBUS sensing pin
 	.pullup_pin	= AT91_PIN_PA24,
+	.vbus_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata csb337_i2c_devices[] = {
@@ -98,6 +100,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PD6,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info csb337_spi_devices[] = {

arch/arm/mach-at91/board-csb637.c

@@ -52,13 +52,15 @@ static void __init csb637_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata csb637_eth_data = {
+static struct macb_platform_data __initdata csb637_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC0,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata csb637_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb637_udc_data = {

arch/arm/mach-at91/board-dt.c

@@ -50,6 +50,7 @@ static void __init ek_init_early(void)
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 };
@@ -82,7 +83,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }

arch/arm/mach-at91/board-eb9200.c

@@ -60,13 +60,15 @@ static void __init eb9200_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata eb9200_eth_data = {
+static struct macb_platform_data __initdata eb9200_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata eb9200_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eb9200_udc_data = {
@@ -75,15 +77,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
 };
 
 static struct at91_cf_data __initdata eb9200_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 static struct at91_mmc_data __initdata eb9200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

arch/arm/mach-at91/board-ecbat91.c

@@ -64,18 +64,23 @@ static void __init ecb_at91init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata ecb_at91eth_data = {
+static struct macb_platform_data __initdata ecb_at91eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata ecb_at91mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-eco920.c

@@ -47,13 +47,15 @@ static void __init eco920_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata eco920_eth_data = {
+static struct macb_platform_data __initdata eco920_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC2,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata eco920_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eco920_udc_data = {
@@ -64,6 +66,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 static struct at91_mmc_data __initdata eco920_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 0,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data eco920_flash_data = {

arch/arm/mach-at91/board-flexibity.c

@@ -52,12 +52,14 @@ static void __init flexibity_init_early(void)
 /* USB Host port */
 static struct at91_usbh_data __initdata flexibity_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /* USB Device port */
 static struct at91_udc_data __initdata flexibity_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /* SPI devices */
@@ -76,6 +78,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
 	.wp_pin		= AT91_PIN_PC4,
+	.vcc_pin	= -EINVAL,
 };
 
 /* LEDs */

arch/arm/mach-at91/board-foxg20.c

@@ -106,6 +106,8 @@ static void __init foxg20_init_early(void)
  */
 static struct at91_usbh_data __initdata foxg20_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -113,7 +115,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
  */
 static struct at91_udc_data __initdata foxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -135,7 +137,7 @@ static struct spi_board_info foxg20_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata foxg20_macb_data = {
+static struct macb_platform_data __initdata foxg20_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -147,6 +149,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = {
 static struct at91_mmc_data __initdata foxg20_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-gsia18s.c

@@ -80,6 +80,8 @@ static void __init gsia18s_init_early(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -87,13 +89,13 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };
@@ -530,6 +532,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
 static struct at91_cf_data __initdata gsia18s_cf1_data = {
 	.irq_pin	= AT91_PIN_PA27,
 	.det_pin	= AT91_PIN_PB30,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PB31,
 	.chipselect	= 5,
 	.flags		= AT91_CF_TRUE_IDE,

arch/arm/mach-at91/board-kafa.c

@@ -61,13 +61,15 @@ static void __init kafa_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata kafa_eth_data = {
+static struct macb_platform_data __initdata kafa_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata kafa_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kafa_udc_data = {

arch/arm/mach-at91/board-kb9202.c

@@ -69,13 +69,15 @@ static void __init kb9202_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata kb9202_eth_data = {
+static struct macb_platform_data __initdata kb9202_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PB29,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata kb9202_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kb9202_udc_data = {
@@ -87,6 +89,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
 	.det_pin	= AT91_PIN_PB2,
 	.slot_b		= 0,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -100,7 +104,7 @@ static struct mtd_partition __initdata kb9202_nand_partition[] = {
 static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC29,
 	.enable_pin	= AT91_PIN_PC28,
 	.parts		= kb9202_nand_partition,

arch/arm/mach-at91/board-neocore926.c

@@ -72,6 +72,7 @@ static void __init neocore926_init_early(void)
 static struct at91_usbh_data __initdata neocore926_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
  */
 static struct at91_udc_data __initdata neocore926_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -149,13 +150,14 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata neocore926_macb_data = {
+static struct macb_platform_data __initdata neocore926_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -190,6 +192,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
 	.enable_pin		= AT91_PIN_PD15,
 	.parts			= neocore926_nand_partition,
 	.num_parts		= ARRAY_SIZE(neocore926_nand_partition),
+	.det_pin		= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
@@ -213,7 +216,7 @@ static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
 static void __init neocore926_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &neocore926_nand_smc_config);
+	sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
 
 	at91_add_device_nand(&neocore926_nand_data);
 }

arch/arm/mach-at91/board-pcontrol-g20.c

@@ -96,9 +96,9 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 static void __init add_device_pcontrol(void)
 {
 	/* configure chip-select 4 (IO compatible to 8051  X4 ) */
-	sam9_smc_configure(4, &pcontrol_smc_config[0]);
+	sam9_smc_configure(0, 4, &pcontrol_smc_config[0]);
 	/* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A  D4 ) */
-	sam9_smc_configure(7, &pcontrol_smc_config[1]);
+	sam9_smc_configure(0, 7, &pcontrol_smc_config[1]);
 }
 
 
@@ -107,6 +107,8 @@ static void __init add_device_pcontrol(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -122,7 +124,7 @@ static struct at91_udc_data __initdata pcontrol_g20_udc_data = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };

arch/arm/mach-at91/board-picotux200.c

@@ -60,13 +60,15 @@ static void __init picotux200_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata picotux200_eth_data = {
+static struct macb_platform_data __initdata picotux200_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
@@ -74,6 +76,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0

arch/arm/mach-at91/board-qil-a9260.c

@@ -77,6 +77,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -84,7 +86,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
@@ -104,7 +106,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA31,
 	.is_rmii	= 1,
 };
@@ -133,7 +135,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -161,7 +163,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -172,9 +174,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*
@@ -251,7 +253,7 @@ static void __init ek_board_init(void)
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	/* shutdown controller, wakeup button (5 msec low) */
-	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
+	at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
 				| AT91_SHDW_RTTWKEN);
 }
 

arch/arm/mach-at91/board-rm9200dk.c

@@ -65,13 +65,15 @@ static void __init dk_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata dk_eth_data = {
+static struct macb_platform_data __initdata dk_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata dk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata dk_udc_data = {
@@ -80,16 +82,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
 };
 
 static struct at91_cf_data __initdata dk_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -143,7 +148,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
 	.cle		= 21,
 	.det_pin	= AT91_PIN_PB1,
 	.rdy_pin	= AT91_PIN_PC2,
-	// .enable_pin	= ... not there
+	.enable_pin	= -EINVAL,
 	.parts		= dk_nand_partition,
 	.num_parts	= ARRAY_SIZE(dk_nand_partition),
 };

arch/arm/mach-at91/board-rm9200ek.c

@@ -65,13 +65,15 @@ static void __init ek_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata ek_eth_data = {
+static struct macb_platform_data __initdata ek_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {
@@ -85,6 +87,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

arch/arm/mach-at91/board-rsi-ews.c

@@ -60,7 +60,7 @@ static void __init rsi_ews_init_early(void)
 /*
  * Ethernet
  */
-static struct at91_eth_data rsi_ews_eth_data __initdata = {
+static struct macb_platform_data rsi_ews_eth_data __initdata = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
@@ -70,6 +70,8 @@ static struct at91_eth_data rsi_ews_eth_data __initdata = {
  */
 static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*

arch/arm/mach-at91/board-sam9-l9260.c

@@ -72,6 +72,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -109,7 +111,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 0,
 };
@@ -134,7 +136,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -162,7 +164,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -176,7 +178,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC8,
 	.wp_pin		= AT91_PIN_PC4,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init ek_board_init(void)

arch/arm/mach-at91/board-sam9260ek.c

@@ -75,6 +75,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -151,7 +153,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -176,7 +178,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -211,7 +213,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -223,9 +225,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9261ek.c

@@ -131,7 +131,7 @@ static struct sam9_smc_config __initdata dm9000_smc_config = {
 static void __init ek_add_device_dm9000(void)
 {
 	/* Configure chip-select 2 (DM9000) */
-	sam9_smc_configure(2, &dm9000_smc_config);
+	sam9_smc_configure(0, 2, &dm9000_smc_config);
 
 	/* Configure Reset signal as output */
 	at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -151,6 +151,8 @@ static void __init ek_add_device_dm9000(void) {}
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -159,7 +161,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -182,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -217,7 +219,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -345,6 +347,9 @@ static struct spi_board_info ek_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */

arch/arm/mach-at91/board-sam9263ek.c

@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -151,14 +152,14 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,
@@ -218,7 +219,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9g20ek.c

@@ -86,6 +86,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -123,7 +125,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -195,7 +198,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= -EINVAL,
 	},
 
 };
@@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
 #else

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -69,6 +69,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -100,6 +101,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -EINVAL,
 	},
 };
 
@@ -115,7 +117,7 @@ static struct mci_platform_data __initdata mci1_data = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PD5,
 	.is_rmii	= 1,
 };
@@ -143,6 +145,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -175,7 +178,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -330,6 +333,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9rlek.c

@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -91,7 +91,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.parts		= ek_nand_partition,
@@ -119,7 +119,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -204,6 +204,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-snapper9260.c

@@ -57,15 +57,19 @@ static void __init snapper9260_init_early(void)
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata snapper9260_udc_data = {
 	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
 	.vbus_active_low	= 1,
 	.vbus_polled		= 1,
+	.pullup_pin		= -EINVAL,
 };
 
-static struct at91_eth_data snapper9260_macb_data = {
+static struct macb_platform_data snapper9260_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -104,6 +108,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
 	.parts		= snapper9260_nand_partitions,
 	.num_parts	= ARRAY_SIZE(snapper9260_nand_partitions),
 	.bus_width_16	= 0,
+	.enable_pin	= -EINVAL,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {
@@ -149,7 +155,7 @@ static struct i2c_board_info __initdata snapper9260_i2c_devices[] = {
 static void __init snapper9260_add_device_nand(void)
 {
 	at91_set_A_periph(AT91_PIN_PC14, 0);
-	sam9_smc_configure(3, &snapper9260_nand_smc_config);
+	sam9_smc_configure(0, 3, &snapper9260_nand_smc_config);
 	at91_add_device_nand(&snapper9260_nand_data);
 }
 

arch/arm/mach-at91/board-stamp9g20.c

@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata nand_smc_config = {
@@ -108,7 +109,7 @@ static struct sam9_smc_config __initdata nand_smc_config = {
 static void __init add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &nand_smc_config);
+	sam9_smc_configure(0, 3, &nand_smc_config);
 
 	at91_add_device_nand(&nand_data);
 }
@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+		.detect_pin	= -1,
+		.wp_pin		= -1,
 	},
 };
 #else
 static struct at91_mmc_data __initdata mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -137,6 +143,8 @@ static struct at91_mmc_data __initdata mmc_data = {
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -145,19 +153,19 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };

arch/arm/mach-at91/board-usb-a926x.c

@@ -66,6 +66,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -73,7 +75,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB11,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static void __init ek_add_device_udc(void)
@@ -146,7 +148,7 @@ static void __init ek_add_device_spi(void)
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -193,7 +195,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,
@@ -245,9 +247,9 @@ static void __init ek_add_device_nand(void)
 
 	/* configure chip-select 3 (NAND) */
 	if (machine_is_usb_a9g20())
-		sam9_smc_configure(3, &usb_a9g20_nand_smc_config);
+		sam9_smc_configure(0, 3, &usb_a9g20_nand_smc_config);
 	else
-		sam9_smc_configure(3, &usb_a9260_nand_smc_config);
+		sam9_smc_configure(0, 3, &usb_a9260_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -344,7 +346,7 @@ static void __init ek_board_init(void)
 		/* I2C */
 		at91_add_device_i2c(NULL, 0);
 		/* shutdown controller, wakeup button (5 msec low) */
-		at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
+		at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
 				| AT91_SHDW_WKMODE0_LOW
 				| AT91_SHDW_RTTWKEN);
 	}

arch/arm/mach-at91/board-yl-9200.c

@@ -110,7 +110,7 @@ static struct gpio_led yl9200_leds[] = {
 /*
  * Ethernet
  */
-static struct at91_eth_data __initdata yl9200_eth_data = {
+static struct macb_platform_data __initdata yl9200_eth_data = {
 	.phy_irq_pin		= AT91_PIN_PB28,
 	.is_rmii		= 1,
 };
@@ -120,6 +120,8 @@ static struct at91_eth_data __initdata yl9200_eth_data = {
  */
 static struct at91_usbh_data __initdata yl9200_usbh_data = {
 	.ports			= 1,	/* PQFP version of AT91RM9200 */
+	.vbus_pin		= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -137,8 +139,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
  */
 static struct at91_mmc_data __initdata yl9200_mmc_data = {
 	.det_pin	= AT91_PIN_PB9,
-	// .wp_pin	= ... not connected
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*
@@ -175,7 +178,7 @@ static struct mtd_partition __initdata yl9200_nand_partition[] = {
 static struct atmel_nand_data __initdata yl9200_nand_data = {
 	.ale		= 6,
 	.cle		= 7,
-	// .det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
 	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.parts		= yl9200_nand_partition,

arch/arm/mach-at91/generic.h

@@ -29,6 +29,7 @@ extern void __init at91_aic_init(unsigned int priority[]);
  /* Timer */
 struct sys_timer;
 extern struct sys_timer at91rm9200_timer;
+extern void at91sam926x_ioremap_pit(u32 addr);
 extern struct sys_timer at91sam926x_timer;
 extern struct sys_timer at91x40_timer;
 
@@ -59,14 +60,16 @@ extern void at91_irq_resume(void);
 /* reset */
 extern void at91sam9_alt_restart(char, const char *);
 
+/* shutdown */
+extern void at91_ioremap_shdwc(u32 base_addr);
+
  /* GPIO */
 #define AT91RM9200_PQFP		3	/* AT91RM9200 PQFP package has 3 banks */
 #define AT91RM9200_BGA		4	/* AT91RM9200 BGA package has 4 banks */
 
 struct at91_gpio_bank {
 	unsigned short id;		/* peripheral ID */
-	unsigned long offset;		/* offset from system peripheral base */
-	struct clk *clock;		/* associated clock */
+	unsigned long regbase;		/* offset from system peripheral base */
 };
 extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
 extern void __init at91_gpio_irq_setup(void);

arch/arm/mach-at91/gpio.c

@@ -29,8 +29,9 @@
 struct at91_gpio_chip {
 	struct gpio_chip	chip;
 	struct at91_gpio_chip	*next;		/* Bank sharing same clock */
-	struct at91_gpio_bank	*bank;		/* Bank definition */
+	int			id;		/* ID of register bank */
 	void __iomem		*regbase;	/* Base of register bank */
+	struct clk		*clock;		/* associated clock */
 };
 
 #define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
@@ -58,18 +59,17 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip,
 	}
 
 static struct at91_gpio_chip gpio_chip[] = {
-	AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32),
+	AT91_GPIO_CHIP("pioA", 0x00, 32),
+	AT91_GPIO_CHIP("pioB", 0x20, 32),
+	AT91_GPIO_CHIP("pioC", 0x40, 32),
+	AT91_GPIO_CHIP("pioD", 0x60, 32),
+	AT91_GPIO_CHIP("pioE", 0x80, 32),
 };
 
 static int gpio_banks;
 
 static inline void __iomem *pin_to_controller(unsigned pin)
 {
-	pin -= PIN_BASE;
 	pin /= 32;
 	if (likely(pin < gpio_banks))
 		return gpio_chip[pin].regbase;
@@ -79,7 +79,6 @@ static inline void __iomem *pin_to_controller(unsigned pin)
 
 static inline unsigned pin_to_mask(unsigned pin)
 {
-	pin -= PIN_BASE;
 	return 1 << (pin % 32);
 }
 
@@ -274,8 +273,9 @@ static u32 backups[MAX_GPIO_BANKS];
 
 static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
 {
-	unsigned	mask = pin_to_mask(d->irq);
-	unsigned	bank = (d->irq - PIN_BASE) / 32;
+	unsigned	pin = irq_to_gpio(d->irq);
+	unsigned	mask = pin_to_mask(pin);
+	unsigned	bank = pin / 32;
 
 	if (unlikely(bank >= MAX_GPIO_BANKS))
 		return -EINVAL;
@@ -285,7 +285,7 @@ static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
 	else
 		wakeups[bank] &= ~mask;
 
-	irq_set_irq_wake(gpio_chip[bank].bank->id, state);
+	irq_set_irq_wake(gpio_chip[bank].id, state);
 
 	return 0;
 }
@@ -302,7 +302,7 @@ void at91_gpio_suspend(void)
 		__raw_writel(wakeups[i], pio + PIO_IER);
 
 		if (!wakeups[i])
-			clk_disable(gpio_chip[i].bank->clock);
+			clk_disable(gpio_chip[i].clock);
 		else {
 #ifdef CONFIG_PM_DEBUG
 			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
@@ -319,7 +319,7 @@ void at91_gpio_resume(void)
 		void __iomem	*pio = gpio_chip[i].regbase;
 
 		if (!wakeups[i])
-			clk_enable(gpio_chip[i].bank->clock);
+			clk_enable(gpio_chip[i].clock);
 
 		__raw_writel(wakeups[i], pio + PIO_IDR);
 		__raw_writel(backups[i], pio + PIO_IER);
@@ -344,8 +344,9 @@ void at91_gpio_resume(void)
 
 static void gpio_irq_mask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IDR);
@@ -353,8 +354,9 @@ static void gpio_irq_mask(struct irq_data *d)
 
 static void gpio_irq_unmask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IER);
@@ -382,7 +384,7 @@ static struct irq_chip gpio_irqchip = {
 
 static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 {
-	unsigned	pin;
+	unsigned	irq_pin;
 	struct irq_data *idata = irq_desc_get_irq_data(desc);
 	struct irq_chip *chip = irq_data_get_irq_chip(idata);
 	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
@@ -405,12 +407,12 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 			continue;
 		}
 
-		pin = at91_gpio->chip.base;
+		irq_pin = gpio_to_irq(at91_gpio->chip.base);
 
 		while (isr) {
 			if (isr & 1)
-				generic_handle_irq(pin);
-			pin++;
+				generic_handle_irq(irq_pin);
+			irq_pin++;
 			isr >>= 1;
 		}
 	}
@@ -438,7 +440,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused)
 		seq_printf(s, "%i:\t", j);
 
 		for (bank = 0; bank < gpio_banks; bank++) {
-			unsigned	pin  = PIN_BASE + (32 * bank) + j;
+			unsigned	pin  = (32 * bank) + j;
 			void __iomem	*pio = pin_to_controller(pin);
 			unsigned	mask = pin_to_mask(pin);
 
@@ -491,27 +493,28 @@ static struct lock_class_key gpio_lock_class;
  */
 void __init at91_gpio_irq_setup(void)
 {
-	unsigned		pioc, pin;
+	unsigned		pioc, irq = gpio_to_irq(0);
 	struct at91_gpio_chip	*this, *prev;
 
-	for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL;
+	for (pioc = 0, this = gpio_chip, prev = NULL;
 			pioc++ < gpio_banks;
 			prev = this, this++) {
-		unsigned	id = this->bank->id;
+		unsigned	id = this->id;
 		unsigned	i;
 
 		__raw_writel(~0, this->regbase + PIO_IDR);
 
-		for (i = 0, pin = this->chip.base; i < 32; i++, pin++) {
-			irq_set_lockdep_class(pin, &gpio_lock_class);
+		for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
+		     i++, irq++) {
+			irq_set_lockdep_class(irq, &gpio_lock_class);
 
 			/*
 			 * Can use the "simple" and not "edge" handler since it's
 			 * shorter, and the AIC handles interrupts sanely.
 			 */
-			irq_set_chip_and_handler(pin, &gpio_irqchip,
+			irq_set_chip_and_handler(irq, &gpio_irqchip,
 						 handle_simple_irq);
-			set_irq_flags(pin, IRQF_VALID);
+			set_irq_flags(irq, IRQF_VALID);
 		}
 
 		/* The toplevel handler handles one bank of GPIOs, except
@@ -524,7 +527,7 @@ void __init at91_gpio_irq_setup(void)
 		irq_set_chip_data(id, this);
 		irq_set_chained_handler(id, gpio_irq_handler);
 	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+	pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
 }
 
 /* gpiolib support */
@@ -612,16 +615,26 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
 	for (i = 0; i < nr_banks; i++) {
 		at91_gpio = &gpio_chip[i];
 
-		at91_gpio->bank = &data[i];
-		at91_gpio->chip.base = PIN_BASE + i * 32;
-		at91_gpio->regbase = at91_gpio->bank->offset +
-			(void __iomem *)AT91_VA_BASE_SYS;
+		at91_gpio->id = data[i].id;
+		at91_gpio->chip.base = i * 32;
+
+		at91_gpio->regbase = ioremap(data[i].regbase, 512);
+		if (!at91_gpio->regbase) {
+			pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
+			continue;
+		}
+
+		at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
+		if (!at91_gpio->clock) {
+			pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", i);
+			continue;
+		}
 
 		/* enable PIO controller's clock */
-		clk_enable(at91_gpio->bank->clock);
+		clk_enable(at91_gpio->clock);
 
 		/* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
-		if (last && last->bank->id == at91_gpio->bank->id)
+		if (last && last->id == at91_gpio->id)
 			last->next = at91_gpio;
 		last = at91_gpio;
 

arch/arm/mach-at91/include/mach/at91_aic.h

@@ -16,7 +16,19 @@
 #ifndef AT91_AIC_H
 #define AT91_AIC_H
 
-#define AT91_AIC_SMR(n)		(AT91_AIC + ((n) * 4))	/* Source Mode Registers 0-31 */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_aic_base;
+
+#define at91_aic_read(field) \
+	__raw_readl(at91_aic_base + field)
+
+#define at91_aic_write(field, value) \
+	__raw_writel(value, at91_aic_base + field);
+#else
+.extern at91_aic_base
+#endif
+
+#define AT91_AIC_SMR(n)		((n) * 4)		/* Source Mode Registers 0-31 */
 #define		AT91_AIC_PRIOR		(7 << 0)		/* Priority Level */
 #define		AT91_AIC_SRCTYPE	(3 << 5)		/* Interrupt Source Type */
 #define			AT91_AIC_SRCTYPE_LOW		(0 << 5)
@@ -24,30 +36,30 @@
 #define			AT91_AIC_SRCTYPE_HIGH		(2 << 5)
 #define			AT91_AIC_SRCTYPE_RISING		(3 << 5)
 
-#define AT91_AIC_SVR(n)		(AT91_AIC + 0x80 + ((n) * 4))	/* Source Vector Registers 0-31 */
-#define AT91_AIC_IVR		(AT91_AIC + 0x100)	/* Interrupt Vector Register */
-#define AT91_AIC_FVR		(AT91_AIC + 0x104)	/* Fast Interrupt Vector Register */
-#define AT91_AIC_ISR		(AT91_AIC + 0x108)	/* Interrupt Status Register */
+#define AT91_AIC_SVR(n)		(0x80 + ((n) * 4))	/* Source Vector Registers 0-31 */
+#define AT91_AIC_IVR		0x100			/* Interrupt Vector Register */
+#define AT91_AIC_FVR		0x104			/* Fast Interrupt Vector Register */
+#define AT91_AIC_ISR		0x108			/* Interrupt Status Register */
 #define		AT91_AIC_IRQID		(0x1f << 0)		/* Current Interrupt Identifier */
 
-#define AT91_AIC_IPR		(AT91_AIC + 0x10c)	/* Interrupt Pending Register */
-#define AT91_AIC_IMR		(AT91_AIC + 0x110)	/* Interrupt Mask Register */
-#define AT91_AIC_CISR		(AT91_AIC + 0x114)	/* Core Interrupt Status Register */
+#define AT91_AIC_IPR		0x10c			/* Interrupt Pending Register */
+#define AT91_AIC_IMR		0x110			/* Interrupt Mask Register */
+#define AT91_AIC_CISR		0x114			/* Core Interrupt Status Register */
 #define		AT91_AIC_NFIQ		(1 << 0)		/* nFIQ Status */
 #define		AT91_AIC_NIRQ		(1 << 1)		/* nIRQ Status */
 
-#define AT91_AIC_IECR		(AT91_AIC + 0x120)	/* Interrupt Enable Command Register */
-#define AT91_AIC_IDCR		(AT91_AIC + 0x124)	/* Interrupt Disable Command Register */
-#define AT91_AIC_ICCR		(AT91_AIC + 0x128)	/* Interrupt Clear Command Register */
-#define AT91_AIC_ISCR		(AT91_AIC + 0x12c)	/* Interrupt Set Command Register */
-#define AT91_AIC_EOICR		(AT91_AIC + 0x130)	/* End of Interrupt Command Register */
-#define AT91_AIC_SPU		(AT91_AIC + 0x134)	/* Spurious Interrupt Vector Register */
-#define AT91_AIC_DCR		(AT91_AIC + 0x138)	/* Debug Control Register */
+#define AT91_AIC_IECR		0x120			/* Interrupt Enable Command Register */
+#define AT91_AIC_IDCR		0x124			/* Interrupt Disable Command Register */
+#define AT91_AIC_ICCR		0x128			/* Interrupt Clear Command Register */
+#define AT91_AIC_ISCR		0x12c			/* Interrupt Set Command Register */
+#define AT91_AIC_EOICR		0x130			/* End of Interrupt Command Register */
+#define AT91_AIC_SPU		0x134			/* Spurious Interrupt Vector Register */
+#define AT91_AIC_DCR		0x138			/* Debug Control Register */
 #define		AT91_AIC_DCR_PROT	(1 << 0)		/* Protection Mode */
 #define		AT91_AIC_DCR_GMSK	(1 << 1)		/* General Mask */
 
-#define AT91_AIC_FFER		(AT91_AIC + 0x140)	/* Fast Forcing Enable Register [SAM9 only] */
-#define AT91_AIC_FFDR		(AT91_AIC + 0x144)	/* Fast Forcing Disable Register [SAM9 only] */
-#define AT91_AIC_FFSR		(AT91_AIC + 0x148)	/* Fast Forcing Status Register [SAM9 only] */
+#define AT91_AIC_FFER		0x140			/* Fast Forcing Enable Register [SAM9 only] */
+#define AT91_AIC_FFDR		0x144			/* Fast Forcing Disable Register [SAM9 only] */
+#define AT91_AIC_FFSR		0x148			/* Fast Forcing Status Register [SAM9 only] */
 
 #endif

arch/arm/mach-at91/include/mach/at91_dbgu.h

@@ -19,7 +19,7 @@
 #define dbgu_readl(dbgu, field) \
 	__raw_readl(AT91_VA_BASE_SYS + dbgu + AT91_DBGU_ ## field)
 
-#ifdef AT91_DBGU
+#if !defined(CONFIG_ARCH_AT91X40)
 #define AT91_DBGU_CR		(0x00)	/* Control Register */
 #define AT91_DBGU_MR		(0x04)	/* Mode Register */
 #define AT91_DBGU_IER		(0x08)	/* Interrupt Enable Register */

arch/arm/mach-at91/include/mach/at91_pit.h

@@ -16,16 +16,16 @@
 #ifndef AT91_PIT_H
 #define AT91_PIT_H
 
-#define AT91_PIT_MR		(AT91_PIT + 0x00)	/* Mode Register */
+#define AT91_PIT_MR		0x00			/* Mode Register */
 #define		AT91_PIT_PITIEN		(1 << 25)		/* Timer Interrupt Enable */
 #define		AT91_PIT_PITEN		(1 << 24)		/* Timer Enabled */
 #define		AT91_PIT_PIV		(0xfffff)		/* Periodic Interval Value */
 
-#define AT91_PIT_SR		(AT91_PIT + 0x04)	/* Status Register */
+#define AT91_PIT_SR		0x04			/* Status Register */
 #define		AT91_PIT_PITS		(1 << 0)		/* Timer Status */
 
-#define AT91_PIT_PIVR		(AT91_PIT + 0x08)	/* Periodic Interval Value Register */
-#define AT91_PIT_PIIR		(AT91_PIT + 0x0c)	/* Periodic Interval Image Register */
+#define AT91_PIT_PIVR		0x08			/* Periodic Interval Value Register */
+#define AT91_PIT_PIIR		0x0c			/* Periodic Interval Image Register */
 #define		AT91_PIT_PICNT		(0xfff << 20)		/* Interval Counter */
 #define		AT91_PIT_CPIV		(0xfffff)		/* Inverval Value */
 

arch/arm/mach-at91/include/mach/at91_rtc.h

@@ -16,7 +16,7 @@
 #ifndef AT91_RTC_H
 #define AT91_RTC_H
 
-#define	AT91_RTC_CR		(AT91_RTC + 0x00)	/* Control Register */
+#define	AT91_RTC_CR		0x00			/* Control Register */
 #define		AT91_RTC_UPDTIM		(1 <<  0)		/* Update Request Time Register */
 #define		AT91_RTC_UPDCAL		(1 <<  1)		/* Update Request Calendar Register */
 #define		AT91_RTC_TIMEVSEL	(3 <<  8)		/* Time Event Selection */
@@ -29,44 +29,44 @@
 #define			AT91_RTC_CALEVSEL_MONTH		(1 << 16)
 #define			AT91_RTC_CALEVSEL_YEAR		(2 << 16)
 
-#define	AT91_RTC_MR		(AT91_RTC + 0x04)	/* Mode Register */
+#define	AT91_RTC_MR		0x04			/* Mode Register */
 #define			AT91_RTC_HRMOD		(1 <<  0)		/* 12/24 Hour Mode */
 
-#define	AT91_RTC_TIMR		(AT91_RTC + 0x08)	/* Time Register */
+#define	AT91_RTC_TIMR		0x08			/* Time Register */
 #define		AT91_RTC_SEC		(0x7f <<  0)		/* Current Second */
 #define		AT91_RTC_MIN		(0x7f <<  8)		/* Current Minute */
 #define		AT91_RTC_HOUR		(0x3f << 16)		/* Current Hour */
 #define		AT91_RTC_AMPM		(1    << 22)		/* Ante Meridiem Post Meridiem Indicator */
 
-#define	AT91_RTC_CALR		(AT91_RTC + 0x0c)	/* Calendar Register */
+#define	AT91_RTC_CALR		0x0c			/* Calendar Register */
 #define		AT91_RTC_CENT		(0x7f <<  0)		/* Current Century */
 #define		AT91_RTC_YEAR		(0xff <<  8)		/* Current Year */
 #define		AT91_RTC_MONTH		(0x1f << 16)		/* Current Month */
 #define		AT91_RTC_DAY		(7    << 21)		/* Current Day */
 #define		AT91_RTC_DATE		(0x3f << 24)		/* Current Date */
 
-#define	AT91_RTC_TIMALR		(AT91_RTC + 0x10)	/* Time Alarm Register */
+#define	AT91_RTC_TIMALR		0x10			/* Time Alarm Register */
 #define		AT91_RTC_SECEN		(1 <<  7)		/* Second Alarm Enable */
 #define		AT91_RTC_MINEN		(1 << 15)		/* Minute Alarm Enable */
 #define		AT91_RTC_HOUREN		(1 << 23)		/* Hour Alarm Enable */
 
-#define	AT91_RTC_CALALR		(AT91_RTC + 0x14)	/* Calendar Alarm Register */
+#define	AT91_RTC_CALALR		0x14			/* Calendar Alarm Register */
 #define		AT91_RTC_MTHEN		(1 << 23)		/* Month Alarm Enable */
 #define		AT91_RTC_DATEEN		(1 << 31)		/* Date Alarm Enable */
 
-#define	AT91_RTC_SR		(AT91_RTC + 0x18)	/* Status Register */
+#define	AT91_RTC_SR		0x18			/* Status Register */
 #define		AT91_RTC_ACKUPD		(1 <<  0)		/* Acknowledge for Update */
 #define		AT91_RTC_ALARM		(1 <<  1)		/* Alarm Flag */
 #define		AT91_RTC_SECEV		(1 <<  2)		/* Second Event */
 #define		AT91_RTC_TIMEV		(1 <<  3)		/* Time Event */
 #define		AT91_RTC_CALEV		(1 <<  4)		/* Calendar Event */
 
-#define	AT91_RTC_SCCR		(AT91_RTC + 0x1c)	/* Status Clear Command Register */
-#define	AT91_RTC_IER		(AT91_RTC + 0x20)	/* Interrupt Enable Register */
-#define	AT91_RTC_IDR		(AT91_RTC + 0x24)	/* Interrupt Disable Register */
-#define	AT91_RTC_IMR		(AT91_RTC + 0x28)	/* Interrupt Mask Register */
+#define	AT91_RTC_SCCR		0x1c			/* Status Clear Command Register */
+#define	AT91_RTC_IER		0x20			/* Interrupt Enable Register */
+#define	AT91_RTC_IDR		0x24			/* Interrupt Disable Register */
+#define	AT91_RTC_IMR		0x28			/* Interrupt Mask Register */
 
-#define	AT91_RTC_VER		(AT91_RTC + 0x2c)	/* Valid Entry Register */
+#define	AT91_RTC_VER		0x2c			/* Valid Entry Register */
 #define		AT91_RTC_NVTIM		(1 <<  0)		/* Non valid Time */
 #define		AT91_RTC_NVCAL		(1 <<  1)		/* Non valid Calendar */
 #define		AT91_RTC_NVTIMALR	(1 <<  2)		/* Non valid Time Alarm */

arch/arm/mach-at91/include/mach/at91_shdwc.h

@@ -16,11 +16,21 @@
 #ifndef AT91_SHDWC_H
 #define AT91_SHDWC_H
 
-#define AT91_SHDW_CR		(AT91_SHDWC + 0x00)	/* Shut Down Control Register */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_shdwc_base;
+
+#define at91_shdwc_read(field) \
+	__raw_readl(at91_shdwc_base + field)
+
+#define at91_shdwc_write(field, value) \
+	__raw_writel(value, at91_shdwc_base + field);
+#endif
+
+#define AT91_SHDW_CR		0x00			/* Shut Down Control Register */
 #define		AT91_SHDW_SHDW		(1    << 0)		/* Shut Down command */
 #define		AT91_SHDW_KEY		(0xa5 << 24)		/* KEY Password */
 
-#define AT91_SHDW_MR		(AT91_SHDWC + 0x04)	/* Shut Down Mode Register */
+#define AT91_SHDW_MR		0x04			/* Shut Down Mode Register */
 #define		AT91_SHDW_WKMODE0	(3 << 0)		/* Wake-up 0 Mode Selection */
 #define			AT91_SHDW_WKMODE0_NONE		0
 #define			AT91_SHDW_WKMODE0_HIGH		1
@@ -30,7 +40,7 @@
 #define			AT91_SHDW_CPTWK0_(x)	((x) << 4)
 #define		AT91_SHDW_RTTWKEN	(1   << 16)		/* Real Time Timer Wake-up Enable */
 
-#define AT91_SHDW_SR		(AT91_SHDWC + 0x08)	/* Shut Down Status Register */
+#define AT91_SHDW_SR		0x08			/* Shut Down Status Register */
 #define		AT91_SHDW_WAKEUP0	(1 <<  0)		/* Wake-up 0 Status */
 #define		AT91_SHDW_RTTWK		(1 << 16)		/* Real-time Timer Wake-up */
 #define		AT91_SHDW_RTCWK		(1 << 17)		/* Real-time Clock Wake-up [SAM9RL] */

arch/arm/mach-at91/include/mach/at91cap9.h

@@ -79,29 +79,28 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_ECC	(0xffffe200 - AT91_BASE_SYS)
 #define AT91_BCRAMC	(0xffffe400 - AT91_BASE_SYS)
 #define AT91_DDRSDRC0	(0xffffe600 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffe800 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_CCFG	(0xffffeb10 - AT91_BASE_SYS)
-#define AT91_DMA	(0xffffec00 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(cpu_is_at91cap9_revB() ?	\
 			(0xfffffd50 - AT91_BASE_SYS) :	\
 			(0xfffffd60 - AT91_BASE_SYS))
 
+#define AT91CAP9_BASE_ECC	0xffffe200
+#define AT91CAP9_BASE_DMA	0xffffec00
+#define AT91CAP9_BASE_SMC	0xffffe800
+#define AT91CAP9_BASE_DBGU	AT91_BASE_DBGU1
+#define AT91CAP9_BASE_PIOA	0xfffff200
+#define AT91CAP9_BASE_PIOB	0xfffff400
+#define AT91CAP9_BASE_PIOC	0xfffff600
+#define AT91CAP9_BASE_PIOD	0xfffff800
+#define AT91CAP9_BASE_SHDWC	0xfffffd10
+#define AT91CAP9_BASE_RTT	0xfffffd20
+#define AT91CAP9_BASE_PIT	0xfffffd30
+#define AT91CAP9_BASE_WDT	0xfffffd40
+
 #define AT91_USART0	AT91CAP9_BASE_US0
 #define AT91_USART1	AT91CAP9_BASE_US1
 #define AT91_USART2	AT91CAP9_BASE_US2

arch/arm/mach-at91/include/mach/at91rm9200.h

@@ -79,17 +79,17 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)	/* Advanced Interrupt Controller */
-#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)	/* Debug Unit */
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)	/* PIO Controller A */
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)	/* PIO Controller B */
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)	/* PIO Controller C */
-#define AT91_PIOD	(0xfffffa00 - AT91_BASE_SYS)	/* PIO Controller D */
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)	/* Power Management Controller */
 #define AT91_ST		(0xfffffd00 - AT91_BASE_SYS)	/* System Timer */
-#define AT91_RTC	(0xfffffe00 - AT91_BASE_SYS)	/* Real-Time Clock */
 #define AT91_MC		(0xffffff00 - AT91_BASE_SYS)	/* Memory Controllers */
 
+#define AT91RM9200_BASE_DBGU	AT91_BASE_DBGU0	/* Debug Unit */
+#define AT91RM9200_BASE_PIOA	0xfffff400	/* PIO Controller A */
+#define AT91RM9200_BASE_PIOB	0xfffff600	/* PIO Controller B */
+#define AT91RM9200_BASE_PIOC	0xfffff800	/* PIO Controller C */
+#define AT91RM9200_BASE_PIOD	0xfffffa00	/* PIO Controller D */
+#define AT91RM9200_BASE_RTC	0xfffffe00	/* Real-Time Clock */
+
 #define AT91_USART0	AT91RM9200_BASE_US0
 #define AT91_USART1	AT91RM9200_BASE_US1
 #define AT91_USART2	AT91RM9200_BASE_US2

arch/arm/mach-at91/include/mach/at91sam9260.h

@@ -80,24 +80,23 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_ECC	(0xffffe800 - AT91_BASE_SYS)
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_CCFG	(0xffffef10 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
+#define AT91SAM9260_BASE_ECC	0xffffe800
+#define AT91SAM9260_BASE_SMC	0xffffec00
+#define AT91SAM9260_BASE_DBGU	AT91_BASE_DBGU0
+#define AT91SAM9260_BASE_PIOA	0xfffff400
+#define AT91SAM9260_BASE_PIOB	0xfffff600
+#define AT91SAM9260_BASE_PIOC	0xfffff800
+#define AT91SAM9260_BASE_SHDWC	0xfffffd10
+#define AT91SAM9260_BASE_RTT	0xfffffd20
+#define AT91SAM9260_BASE_PIT	0xfffffd30
+#define AT91SAM9260_BASE_WDT	0xfffffd40
+
 #define AT91_USART0	AT91SAM9260_BASE_US0
 #define AT91_USART1	AT91SAM9260_BASE_US1
 #define AT91_USART2	AT91SAM9260_BASE_US2

arch/arm/mach-at91/include/mach/at91sam9261.h

@@ -66,21 +66,21 @@
  * System Peripherals (offset from AT91_BASE_SYS)
  */
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd50 - AT91_BASE_SYS)
 
+#define AT91SAM9261_BASE_SMC	0xffffec00
+#define AT91SAM9261_BASE_DBGU	AT91_BASE_DBGU0
+#define AT91SAM9261_BASE_PIOA	0xfffff400
+#define AT91SAM9261_BASE_PIOB	0xfffff600
+#define AT91SAM9261_BASE_PIOC	0xfffff800
+#define AT91SAM9261_BASE_SHDWC	0xfffffd10
+#define AT91SAM9261_BASE_RTT	0xfffffd20
+#define AT91SAM9261_BASE_PIT	0xfffffd30
+#define AT91SAM9261_BASE_WDT	0xfffffd40
+
 #define AT91_USART0	AT91SAM9261_BASE_US0
 #define AT91_USART1	AT91SAM9261_BASE_US1
 #define AT91_USART2	AT91SAM9261_BASE_US2

arch/arm/mach-at91/include/mach/at91sam9263.h

@@ -74,30 +74,29 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_ECC0	(0xffffe000 - AT91_BASE_SYS)
 #define AT91_SDRAMC0	(0xffffe200 - AT91_BASE_SYS)
-#define AT91_SMC0	(0xffffe400 - AT91_BASE_SYS)
-#define AT91_ECC1	(0xffffe600 - AT91_BASE_SYS)
 #define AT91_SDRAMC1	(0xffffe800 - AT91_BASE_SYS)
-#define AT91_SMC1	(0xffffea00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffec00 - AT91_BASE_SYS)
-#define AT91_CCFG	(0xffffed10 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT0	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
-#define AT91_RTT1	(0xfffffd50 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
 
+#define AT91SAM9263_BASE_ECC0	0xffffe000
+#define AT91SAM9263_BASE_SMC0	0xffffe400
+#define AT91SAM9263_BASE_ECC1	0xffffe600
+#define AT91SAM9263_BASE_SMC1	0xffffea00
+#define AT91SAM9263_BASE_DBGU	AT91_BASE_DBGU1
+#define AT91SAM9263_BASE_PIOA	0xfffff200
+#define AT91SAM9263_BASE_PIOB	0xfffff400
+#define AT91SAM9263_BASE_PIOC	0xfffff600
+#define AT91SAM9263_BASE_PIOD	0xfffff800
+#define AT91SAM9263_BASE_PIOE	0xfffffa00
+#define AT91SAM9263_BASE_SHDWC	0xfffffd10
+#define AT91SAM9263_BASE_RTT0	0xfffffd20
+#define AT91SAM9263_BASE_PIT	0xfffffd30
+#define AT91SAM9263_BASE_WDT	0xfffffd40
+#define AT91SAM9263_BASE_RTT1	0xfffffd50
+
 #define AT91_USART0	AT91SAM9263_BASE_US0
 #define AT91_USART1	AT91SAM9263_BASE_US1
 #define AT91_USART2	AT91SAM9263_BASE_US2

arch/arm/mach-at91/include/mach/at91sam9_smc.h

@@ -16,7 +16,9 @@
 #ifndef AT91SAM9_SMC_H
 #define AT91SAM9_SMC_H
 
-#define AT91_SMC_SETUP(n)	(AT91_SMC + 0x00 + ((n)*0x10))	/* Setup Register for CS n */
+#include <mach/cpu.h>
+
+#define AT91_SMC_SETUP		0x00				/* Setup Register for CS n */
 #define		AT91_SMC_NWESETUP	(0x3f << 0)			/* NWE Setup Length */
 #define			AT91_SMC_NWESETUP_(x)	((x) << 0)
 #define		AT91_SMC_NCS_WRSETUP	(0x3f << 8)			/* NCS Setup Length in Write Access */
@@ -26,7 +28,7 @@
 #define		AT91_SMC_NCS_RDSETUP	(0x3f << 24)			/* NCS Setup Length in Read Access */
 #define			AT91_SMC_NCS_RDSETUP_(x)	((x) << 24)
 
-#define AT91_SMC_PULSE(n)	(AT91_SMC + 0x04 + ((n)*0x10))	/* Pulse Register for CS n */
+#define AT91_SMC_PULSE		0x04				/* Pulse Register for CS n */
 #define		AT91_SMC_NWEPULSE	(0x7f <<  0)			/* NWE Pulse Length */
 #define			AT91_SMC_NWEPULSE_(x)	((x) << 0)
 #define		AT91_SMC_NCS_WRPULSE	(0x7f <<  8)			/* NCS Pulse Length in Write Access */
@@ -36,13 +38,13 @@
 #define		AT91_SMC_NCS_RDPULSE	(0x7f << 24)			/* NCS Pulse Length in Read Access */
 #define			AT91_SMC_NCS_RDPULSE_(x)((x) << 24)
 
-#define AT91_SMC_CYCLE(n)	(AT91_SMC + 0x08 + ((n)*0x10))	/* Cycle Register for CS n */
+#define AT91_SMC_CYCLE		0x08				/* Cycle Register for CS n */
 #define		AT91_SMC_NWECYCLE	(0x1ff << 0 )			/* Total Write Cycle Length */
 #define			AT91_SMC_NWECYCLE_(x)	((x) << 0)
 #define		AT91_SMC_NRDCYCLE	(0x1ff << 16)			/* Total Read Cycle Length */
 #define			AT91_SMC_NRDCYCLE_(x)	((x) << 16)
 
-#define AT91_SMC_MODE(n)	(AT91_SMC + 0x0c + ((n)*0x10))	/* Mode Register for CS n */
+#define AT91_SMC_MODE		0x0c				/* Mode Register for CS n */
 #define		AT91_SMC_READMODE	(1 <<  0)			/* Read Mode */
 #define		AT91_SMC_WRITEMODE	(1 <<  1)			/* Write Mode */
 #define		AT91_SMC_EXNWMODE	(3 <<  4)			/* NWAIT Mode */
@@ -66,11 +68,4 @@
 #define			AT91_SMC_PS_16			(2 << 28)
 #define			AT91_SMC_PS_32			(3 << 28)
 
-#if defined(AT91_SMC1)		/* The AT91SAM9263 has 2 Static Memory contollers */
-#define AT91_SMC1_SETUP(n)	(AT91_SMC1 + 0x00 + ((n)*0x10))	/* Setup Register for CS n */
-#define AT91_SMC1_PULSE(n)	(AT91_SMC1 + 0x04 + ((n)*0x10))	/* Pulse Register for CS n */
-#define AT91_SMC1_CYCLE(n)	(AT91_SMC1 + 0x08 + ((n)*0x10))	/* Cycle Register for CS n */
-#define AT91_SMC1_MODE(n)	(AT91_SMC1 + 0x0c + ((n)*0x10))	/* Mode Register for CS n */
-#endif
-
 #endif

arch/arm/mach-at91/include/mach/at91sam9g45.h

@@ -86,27 +86,27 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_ECC	(0xffffe200 - AT91_BASE_SYS)
 #define AT91_DDRSDRC1	(0xffffe400 - AT91_BASE_SYS)
 #define AT91_DDRSDRC0	(0xffffe600 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffe800 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_DMA	(0xffffec00 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOE	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
-#define AT91_RTC	(0xfffffdb0 - AT91_BASE_SYS)
+
+#define AT91SAM9G45_BASE_ECC	0xffffe200
+#define AT91SAM9G45_BASE_DMA	0xffffec00
+#define AT91SAM9G45_BASE_SMC	0xffffe800
+#define AT91SAM9G45_BASE_DBGU	AT91_BASE_DBGU1
+#define AT91SAM9G45_BASE_PIOA	0xfffff200
+#define AT91SAM9G45_BASE_PIOB	0xfffff400
+#define AT91SAM9G45_BASE_PIOC	0xfffff600
+#define AT91SAM9G45_BASE_PIOD	0xfffff800
+#define AT91SAM9G45_BASE_PIOE	0xfffffa00
+#define AT91SAM9G45_BASE_SHDWC	0xfffffd10
+#define AT91SAM9G45_BASE_RTT	0xfffffd20
+#define AT91SAM9G45_BASE_PIT	0xfffffd30
+#define AT91SAM9G45_BASE_WDT	0xfffffd40
+#define AT91SAM9G45_BASE_RTC	0xfffffdb0
 
 #define AT91_USART0	AT91SAM9G45_BASE_US0
 #define AT91_USART1	AT91SAM9G45_BASE_US1

arch/arm/mach-at91/include/mach/at91sam9rl.h

@@ -69,27 +69,26 @@
 /*
  * System Peripherals (offset from AT91_BASE_SYS)
  */
-#define AT91_DMA	(0xffffe600 - AT91_BASE_SYS)
-#define AT91_ECC	(0xffffe800 - AT91_BASE_SYS)
 #define AT91_SDRAMC0	(0xffffea00 - AT91_BASE_SYS)
-#define AT91_SMC	(0xffffec00 - AT91_BASE_SYS)
 #define AT91_MATRIX	(0xffffee00 - AT91_BASE_SYS)
-#define AT91_CCFG	(0xffffef10 - AT91_BASE_SYS)
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)
-#define AT91_DBGU	(0xfffff200 - AT91_BASE_SYS)
-#define AT91_PIOA	(0xfffff400 - AT91_BASE_SYS)
-#define AT91_PIOB	(0xfffff600 - AT91_BASE_SYS)
-#define AT91_PIOC	(0xfffff800 - AT91_BASE_SYS)
-#define AT91_PIOD	(0xfffffa00 - AT91_BASE_SYS)
 #define AT91_PMC	(0xfffffc00 - AT91_BASE_SYS)
 #define AT91_RSTC	(0xfffffd00 - AT91_BASE_SYS)
-#define AT91_SHDWC	(0xfffffd10 - AT91_BASE_SYS)
-#define AT91_RTT	(0xfffffd20 - AT91_BASE_SYS)
-#define AT91_PIT	(0xfffffd30 - AT91_BASE_SYS)
-#define AT91_WDT	(0xfffffd40 - AT91_BASE_SYS)
 #define AT91_SCKCR	(0xfffffd50 - AT91_BASE_SYS)
 #define AT91_GPBR	(0xfffffd60 - AT91_BASE_SYS)
-#define AT91_RTC	(0xfffffe00 - AT91_BASE_SYS)
+
+#define AT91SAM9RL_BASE_DMA	0xffffe600
+#define AT91SAM9RL_BASE_ECC	0xffffe800
+#define AT91SAM9RL_BASE_SMC	0xffffec00
+#define AT91SAM9RL_BASE_DBGU	AT91_BASE_DBGU0
+#define AT91SAM9RL_BASE_PIOA	0xfffff400
+#define AT91SAM9RL_BASE_PIOB	0xfffff600
+#define AT91SAM9RL_BASE_PIOC	0xfffff800
+#define AT91SAM9RL_BASE_PIOD	0xfffffa00
+#define AT91SAM9RL_BASE_SHDWC	0xfffffd10
+#define AT91SAM9RL_BASE_RTT	0xfffffd20
+#define AT91SAM9RL_BASE_PIT	0xfffffd30
+#define AT91SAM9RL_BASE_WDT	0xfffffd40
+#define AT91SAM9RL_BASE_RTC	0xfffffe00
 
 #define AT91_USART0	AT91SAM9RL_BASE_US0
 #define AT91_USART1	AT91SAM9RL_BASE_US1

arch/arm/mach-at91/include/mach/at91x40.h

@@ -40,7 +40,6 @@
 #define AT91_PIOA	(0xffff0000 - AT91_BASE_SYS)	/* PIO Controller A */
 #define AT91_PS		(0xffff4000 - AT91_BASE_SYS)	/* Power Save */
 #define AT91_WD		(0xffff8000 - AT91_BASE_SYS)	/* Watchdog Timer */
-#define AT91_AIC	(0xfffff000 - AT91_BASE_SYS)	/* Advanced Interrupt Controller */
 
 /*
  * The AT91x40 series doesn't have a debug unit like the other AT91 parts.

arch/arm/mach-at91/include/mach/board.h

@@ -40,13 +40,14 @@
 #include <linux/atmel-mci.h>
 #include <sound/atmel-ac97c.h>
 #include <linux/serial.h>
+#include <linux/platform_data/macb.h>
 
  /* USB Device */
 struct at91_udc_data {
-	u8	vbus_pin;		/* high == host powering us */
+	int	vbus_pin;		/* high == host powering us */
 	u8	vbus_active_low;	/* vbus polarity */
 	u8	vbus_polled;		/* Use polling, not interrupt */
-	u8	pullup_pin;		/* active == D+ pulled up */
+	int	pullup_pin;		/* active == D+ pulled up */
 	u8	pullup_active_low;	/* true == pullup_pin is active low */
 };
 extern void __init at91_add_device_udc(struct at91_udc_data *data);
@@ -56,10 +57,10 @@ extern void __init at91_add_device_usba(struct usba_platform_data *data);
 
  /* Compact Flash */
 struct at91_cf_data {
-	u8	irq_pin;		/* I/O IRQ */
-	u8	det_pin;		/* Card detect */
-	u8	vcc_pin;		/* power switching */
-	u8	rst_pin;		/* card reset */
+	int	irq_pin;		/* I/O IRQ */
+	int	det_pin;		/* Card detect */
+	int	vcc_pin;		/* power switching */
+	int	rst_pin;		/* card reset */
 	u8	chipselect;		/* EBI Chip Select number */
 	u8	flags;
 #define AT91_CF_TRUE_IDE	0x01
@@ -70,37 +71,26 @@ extern void __init at91_add_device_cf(struct at91_cf_data *data);
  /* MMC / SD */
   /* at91_mci platform config */
 struct at91_mmc_data {
-	u8		det_pin;	/* card detect IRQ */
+	int		det_pin;	/* card detect IRQ */
 	unsigned	slot_b:1;	/* uses Slot B */
 	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
-	u8		wp_pin;		/* (SD) writeprotect detect */
-	u8		vcc_pin;	/* power switching (high == on) */
+	int		wp_pin;		/* (SD) writeprotect detect */
+	int		vcc_pin;	/* power switching (high == on) */
 };
 extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
 
   /* atmel-mci platform config */
 extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
 
- /* Ethernet (EMAC & MACB) */
-struct at91_eth_data {
-	u32		phy_mask;
-	u8		phy_irq_pin;	/* PHY IRQ */
-	u8		is_rmii;	/* using RMII interface? */
-};
-extern void __init at91_add_device_eth(struct at91_eth_data *data);
-
-#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
-	|| defined(CONFIG_ARCH_AT91SAM9G45)
-#define eth_platform_data	at91_eth_data
-#endif
+extern void __init at91_add_device_eth(struct macb_platform_data *data);
 
  /* USB Host */
 struct at91_usbh_data {
 	u8		ports;		/* number of ports on root hub */
-	u8		vbus_pin[2];	/* port power-control pin */
+	int		vbus_pin[2];	/* port power-control pin */
 	u8              vbus_pin_inverted;
 	u8              overcurrent_supported;
-	u8              overcurrent_pin[2];
+	int             overcurrent_pin[2];
 	u8              overcurrent_status[2];
 	u8              overcurrent_changed[2];
 };
@@ -110,9 +100,9 @@ extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data);
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
-	u8		enable_pin;	/* chip enable */
-	u8		det_pin;	/* card detect */
-	u8		rdy_pin;	/* ready/busy */
+	int		enable_pin;	/* chip enable */
+	int		det_pin;	/* card detect */
+	int		rdy_pin;	/* ready/busy */
 	u8              rdy_pin_active_low;     /* rdy_pin value is inverted */
 	u8		ale;		/* address line number connected to ALE */
 	u8		cle;		/* address line number connected to CLE */

arch/arm/mach-at91/include/mach/debug-macro.S

@@ -14,9 +14,15 @@
 #include <mach/hardware.h>
 #include <mach/at91_dbgu.h>
 
+#if defined(CONFIG_AT91_DEBUG_LL_DBGU0)
+#define AT91_DBGU AT91_BASE_DBGU0
+#else
+#define AT91_DBGU AT91_BASE_DBGU1
+#endif
+
 	.macro	addruart, rp, rv, tmp
-	ldr	\rp, =(AT91_BASE_SYS + AT91_DBGU)	@ System peripherals (phys address)
-	ldr	\rv, =(AT91_VA_BASE_SYS	+ AT91_DBGU)	@ System peripherals (virt address)
+	ldr	\rp, =AT91_DBGU				@ System peripherals (phys address)
+	ldr	\rv, =AT91_IO_P2V(AT91_DBGU)		@ System peripherals (virt address)
 	.endm
 
 	.macro	senduart,rd,rx

arch/arm/mach-at91/include/mach/entry-macro.S

@@ -17,16 +17,17 @@
 	.endm
 
 	.macro  get_irqnr_preamble, base, tmp
-	ldr	\base, =(AT91_VA_BASE_SYS + AT91_AIC)		@ base virtual address of AIC peripheral
+	ldr	\base, =at91_aic_base		@ base virtual address of AIC peripheral
+	ldr	\base, [\base]
 	.endm
 
 	.macro  arch_ret_to_user, tmp1, tmp2
 	.endm
 
 	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-	ldr	\irqnr, [\base, #(AT91_AIC_IVR - AT91_AIC)]	@ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt)
-	ldr	\irqstat, [\base, #(AT91_AIC_ISR - AT91_AIC)]	@ read interrupt source number
-	teq	\irqstat, #0					@ ISR is 0 when no current interrupt, or spurious interrupt
-	streq	\tmp, [\base, #(AT91_AIC_EOICR - AT91_AIC)]	@ not going to be handled further, then ACK it now.
+	ldr	\irqnr, [\base, #AT91_AIC_IVR]		@ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt)
+	ldr	\irqstat, [\base, #AT91_AIC_ISR]	@ read interrupt source number
+	teq	\irqstat, #0				@ ISR is 0 when no current interrupt, or spurious interrupt
+	streq	\tmp, [\base, #AT91_AIC_EOICR]		@ not going to be handled further, then ACK it now.
 	.endm
 

arch/arm/mach-at91/include/mach/gpio.h

@@ -16,177 +16,175 @@
 #include <linux/kernel.h>
 #include <asm/irq.h>
 
-#define PIN_BASE		NR_AIC_IRQS
-
 #define MAX_GPIO_BANKS		5
-#define NR_BUILTIN_GPIO		(PIN_BASE + (MAX_GPIO_BANKS * 32))
+#define NR_BUILTIN_GPIO		(MAX_GPIO_BANKS * 32)
 
 /* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */
 
-#define	AT91_PIN_PA0	(PIN_BASE + 0x00 + 0)
-#define	AT91_PIN_PA1	(PIN_BASE + 0x00 + 1)
-#define	AT91_PIN_PA2	(PIN_BASE + 0x00 + 2)
-#define	AT91_PIN_PA3	(PIN_BASE + 0x00 + 3)
-#define	AT91_PIN_PA4	(PIN_BASE + 0x00 + 4)
-#define	AT91_PIN_PA5	(PIN_BASE + 0x00 + 5)
-#define	AT91_PIN_PA6	(PIN_BASE + 0x00 + 6)
-#define	AT91_PIN_PA7	(PIN_BASE + 0x00 + 7)
-#define	AT91_PIN_PA8	(PIN_BASE + 0x00 + 8)
-#define	AT91_PIN_PA9	(PIN_BASE + 0x00 + 9)
-#define	AT91_PIN_PA10	(PIN_BASE + 0x00 + 10)
-#define	AT91_PIN_PA11	(PIN_BASE + 0x00 + 11)
-#define	AT91_PIN_PA12	(PIN_BASE + 0x00 + 12)
-#define	AT91_PIN_PA13	(PIN_BASE + 0x00 + 13)
-#define	AT91_PIN_PA14	(PIN_BASE + 0x00 + 14)
-#define	AT91_PIN_PA15	(PIN_BASE + 0x00 + 15)
-#define	AT91_PIN_PA16	(PIN_BASE + 0x00 + 16)
-#define	AT91_PIN_PA17	(PIN_BASE + 0x00 + 17)
-#define	AT91_PIN_PA18	(PIN_BASE + 0x00 + 18)
-#define	AT91_PIN_PA19	(PIN_BASE + 0x00 + 19)
-#define	AT91_PIN_PA20	(PIN_BASE + 0x00 + 20)
-#define	AT91_PIN_PA21	(PIN_BASE + 0x00 + 21)
-#define	AT91_PIN_PA22	(PIN_BASE + 0x00 + 22)
-#define	AT91_PIN_PA23	(PIN_BASE + 0x00 + 23)
-#define	AT91_PIN_PA24	(PIN_BASE + 0x00 + 24)
-#define	AT91_PIN_PA25	(PIN_BASE + 0x00 + 25)
-#define	AT91_PIN_PA26	(PIN_BASE + 0x00 + 26)
-#define	AT91_PIN_PA27	(PIN_BASE + 0x00 + 27)
-#define	AT91_PIN_PA28	(PIN_BASE + 0x00 + 28)
-#define	AT91_PIN_PA29	(PIN_BASE + 0x00 + 29)
-#define	AT91_PIN_PA30	(PIN_BASE + 0x00 + 30)
-#define	AT91_PIN_PA31	(PIN_BASE + 0x00 + 31)
-
-#define	AT91_PIN_PB0	(PIN_BASE + 0x20 + 0)
-#define	AT91_PIN_PB1	(PIN_BASE + 0x20 + 1)
-#define	AT91_PIN_PB2	(PIN_BASE + 0x20 + 2)
-#define	AT91_PIN_PB3	(PIN_BASE + 0x20 + 3)
-#define	AT91_PIN_PB4	(PIN_BASE + 0x20 + 4)
-#define	AT91_PIN_PB5	(PIN_BASE + 0x20 + 5)
-#define	AT91_PIN_PB6	(PIN_BASE + 0x20 + 6)
-#define	AT91_PIN_PB7	(PIN_BASE + 0x20 + 7)
-#define	AT91_PIN_PB8	(PIN_BASE + 0x20 + 8)
-#define	AT91_PIN_PB9	(PIN_BASE + 0x20 + 9)
-#define	AT91_PIN_PB10	(PIN_BASE + 0x20 + 10)
-#define	AT91_PIN_PB11	(PIN_BASE + 0x20 + 11)
-#define	AT91_PIN_PB12	(PIN_BASE + 0x20 + 12)
-#define	AT91_PIN_PB13	(PIN_BASE + 0x20 + 13)
-#define	AT91_PIN_PB14	(PIN_BASE + 0x20 + 14)
-#define	AT91_PIN_PB15	(PIN_BASE + 0x20 + 15)
-#define	AT91_PIN_PB16	(PIN_BASE + 0x20 + 16)
-#define	AT91_PIN_PB17	(PIN_BASE + 0x20 + 17)
-#define	AT91_PIN_PB18	(PIN_BASE + 0x20 + 18)
-#define	AT91_PIN_PB19	(PIN_BASE + 0x20 + 19)
-#define	AT91_PIN_PB20	(PIN_BASE + 0x20 + 20)
-#define	AT91_PIN_PB21	(PIN_BASE + 0x20 + 21)
-#define	AT91_PIN_PB22	(PIN_BASE + 0x20 + 22)
-#define	AT91_PIN_PB23	(PIN_BASE + 0x20 + 23)
-#define	AT91_PIN_PB24	(PIN_BASE + 0x20 + 24)
-#define	AT91_PIN_PB25	(PIN_BASE + 0x20 + 25)
-#define	AT91_PIN_PB26	(PIN_BASE + 0x20 + 26)
-#define	AT91_PIN_PB27	(PIN_BASE + 0x20 + 27)
-#define	AT91_PIN_PB28	(PIN_BASE + 0x20 + 28)
-#define	AT91_PIN_PB29	(PIN_BASE + 0x20 + 29)
-#define	AT91_PIN_PB30	(PIN_BASE + 0x20 + 30)
-#define	AT91_PIN_PB31	(PIN_BASE + 0x20 + 31)
-
-#define	AT91_PIN_PC0	(PIN_BASE + 0x40 + 0)
-#define	AT91_PIN_PC1	(PIN_BASE + 0x40 + 1)
-#define	AT91_PIN_PC2	(PIN_BASE + 0x40 + 2)
-#define	AT91_PIN_PC3	(PIN_BASE + 0x40 + 3)
-#define	AT91_PIN_PC4	(PIN_BASE + 0x40 + 4)
-#define	AT91_PIN_PC5	(PIN_BASE + 0x40 + 5)
-#define	AT91_PIN_PC6	(PIN_BASE + 0x40 + 6)
-#define	AT91_PIN_PC7	(PIN_BASE + 0x40 + 7)
-#define	AT91_PIN_PC8	(PIN_BASE + 0x40 + 8)
-#define	AT91_PIN_PC9	(PIN_BASE + 0x40 + 9)
-#define	AT91_PIN_PC10	(PIN_BASE + 0x40 + 10)
-#define	AT91_PIN_PC11	(PIN_BASE + 0x40 + 11)
-#define	AT91_PIN_PC12	(PIN_BASE + 0x40 + 12)
-#define	AT91_PIN_PC13	(PIN_BASE + 0x40 + 13)
-#define	AT91_PIN_PC14	(PIN_BASE + 0x40 + 14)
-#define	AT91_PIN_PC15	(PIN_BASE + 0x40 + 15)
-#define	AT91_PIN_PC16	(PIN_BASE + 0x40 + 16)
-#define	AT91_PIN_PC17	(PIN_BASE + 0x40 + 17)
-#define	AT91_PIN_PC18	(PIN_BASE + 0x40 + 18)
-#define	AT91_PIN_PC19	(PIN_BASE + 0x40 + 19)
-#define	AT91_PIN_PC20	(PIN_BASE + 0x40 + 20)
-#define	AT91_PIN_PC21	(PIN_BASE + 0x40 + 21)
-#define	AT91_PIN_PC22	(PIN_BASE + 0x40 + 22)
-#define	AT91_PIN_PC23	(PIN_BASE + 0x40 + 23)
-#define	AT91_PIN_PC24	(PIN_BASE + 0x40 + 24)
-#define	AT91_PIN_PC25	(PIN_BASE + 0x40 + 25)
-#define	AT91_PIN_PC26	(PIN_BASE + 0x40 + 26)
-#define	AT91_PIN_PC27	(PIN_BASE + 0x40 + 27)
-#define	AT91_PIN_PC28	(PIN_BASE + 0x40 + 28)
-#define	AT91_PIN_PC29	(PIN_BASE + 0x40 + 29)
-#define	AT91_PIN_PC30	(PIN_BASE + 0x40 + 30)
-#define	AT91_PIN_PC31	(PIN_BASE + 0x40 + 31)
-
-#define	AT91_PIN_PD0	(PIN_BASE + 0x60 + 0)
-#define	AT91_PIN_PD1	(PIN_BASE + 0x60 + 1)
-#define	AT91_PIN_PD2	(PIN_BASE + 0x60 + 2)
-#define	AT91_PIN_PD3	(PIN_BASE + 0x60 + 3)
-#define	AT91_PIN_PD4	(PIN_BASE + 0x60 + 4)
-#define	AT91_PIN_PD5	(PIN_BASE + 0x60 + 5)
-#define	AT91_PIN_PD6	(PIN_BASE + 0x60 + 6)
-#define	AT91_PIN_PD7	(PIN_BASE + 0x60 + 7)
-#define	AT91_PIN_PD8	(PIN_BASE + 0x60 + 8)
-#define	AT91_PIN_PD9	(PIN_BASE + 0x60 + 9)
-#define	AT91_PIN_PD10	(PIN_BASE + 0x60 + 10)
-#define	AT91_PIN_PD11	(PIN_BASE + 0x60 + 11)
-#define	AT91_PIN_PD12	(PIN_BASE + 0x60 + 12)
-#define	AT91_PIN_PD13	(PIN_BASE + 0x60 + 13)
-#define	AT91_PIN_PD14	(PIN_BASE + 0x60 + 14)
-#define	AT91_PIN_PD15	(PIN_BASE + 0x60 + 15)
-#define	AT91_PIN_PD16	(PIN_BASE + 0x60 + 16)
-#define	AT91_PIN_PD17	(PIN_BASE + 0x60 + 17)
-#define	AT91_PIN_PD18	(PIN_BASE + 0x60 + 18)
-#define	AT91_PIN_PD19	(PIN_BASE + 0x60 + 19)
-#define	AT91_PIN_PD20	(PIN_BASE + 0x60 + 20)
-#define	AT91_PIN_PD21	(PIN_BASE + 0x60 + 21)
-#define	AT91_PIN_PD22	(PIN_BASE + 0x60 + 22)
-#define	AT91_PIN_PD23	(PIN_BASE + 0x60 + 23)
-#define	AT91_PIN_PD24	(PIN_BASE + 0x60 + 24)
-#define	AT91_PIN_PD25	(PIN_BASE + 0x60 + 25)
-#define	AT91_PIN_PD26	(PIN_BASE + 0x60 + 26)
-#define	AT91_PIN_PD27	(PIN_BASE + 0x60 + 27)
-#define	AT91_PIN_PD28	(PIN_BASE + 0x60 + 28)
-#define	AT91_PIN_PD29	(PIN_BASE + 0x60 + 29)
-#define	AT91_PIN_PD30	(PIN_BASE + 0x60 + 30)
-#define	AT91_PIN_PD31	(PIN_BASE + 0x60 + 31)
-
-#define	AT91_PIN_PE0	(PIN_BASE + 0x80 + 0)
-#define	AT91_PIN_PE1	(PIN_BASE + 0x80 + 1)
-#define	AT91_PIN_PE2	(PIN_BASE + 0x80 + 2)
-#define	AT91_PIN_PE3	(PIN_BASE + 0x80 + 3)
-#define	AT91_PIN_PE4	(PIN_BASE + 0x80 + 4)
-#define	AT91_PIN_PE5	(PIN_BASE + 0x80 + 5)
-#define	AT91_PIN_PE6	(PIN_BASE + 0x80 + 6)
-#define	AT91_PIN_PE7	(PIN_BASE + 0x80 + 7)
-#define	AT91_PIN_PE8	(PIN_BASE + 0x80 + 8)
-#define	AT91_PIN_PE9	(PIN_BASE + 0x80 + 9)
-#define	AT91_PIN_PE10	(PIN_BASE + 0x80 + 10)
-#define	AT91_PIN_PE11	(PIN_BASE + 0x80 + 11)
-#define	AT91_PIN_PE12	(PIN_BASE + 0x80 + 12)
-#define	AT91_PIN_PE13	(PIN_BASE + 0x80 + 13)
-#define	AT91_PIN_PE14	(PIN_BASE + 0x80 + 14)
-#define	AT91_PIN_PE15	(PIN_BASE + 0x80 + 15)
-#define	AT91_PIN_PE16	(PIN_BASE + 0x80 + 16)
-#define	AT91_PIN_PE17	(PIN_BASE + 0x80 + 17)
-#define	AT91_PIN_PE18	(PIN_BASE + 0x80 + 18)
-#define	AT91_PIN_PE19	(PIN_BASE + 0x80 + 19)
-#define	AT91_PIN_PE20	(PIN_BASE + 0x80 + 20)
-#define	AT91_PIN_PE21	(PIN_BASE + 0x80 + 21)
-#define	AT91_PIN_PE22	(PIN_BASE + 0x80 + 22)
-#define	AT91_PIN_PE23	(PIN_BASE + 0x80 + 23)
-#define	AT91_PIN_PE24	(PIN_BASE + 0x80 + 24)
-#define	AT91_PIN_PE25	(PIN_BASE + 0x80 + 25)
-#define	AT91_PIN_PE26	(PIN_BASE + 0x80 + 26)
-#define	AT91_PIN_PE27	(PIN_BASE + 0x80 + 27)
-#define	AT91_PIN_PE28	(PIN_BASE + 0x80 + 28)
-#define	AT91_PIN_PE29	(PIN_BASE + 0x80 + 29)
-#define	AT91_PIN_PE30	(PIN_BASE + 0x80 + 30)
-#define	AT91_PIN_PE31	(PIN_BASE + 0x80 + 31)
+#define	AT91_PIN_PA0	(0x00 + 0)
+#define	AT91_PIN_PA1	(0x00 + 1)
+#define	AT91_PIN_PA2	(0x00 + 2)
+#define	AT91_PIN_PA3	(0x00 + 3)
+#define	AT91_PIN_PA4	(0x00 + 4)
+#define	AT91_PIN_PA5	(0x00 + 5)
+#define	AT91_PIN_PA6	(0x00 + 6)
+#define	AT91_PIN_PA7	(0x00 + 7)
+#define	AT91_PIN_PA8	(0x00 + 8)
+#define	AT91_PIN_PA9	(0x00 + 9)
+#define	AT91_PIN_PA10	(0x00 + 10)
+#define	AT91_PIN_PA11	(0x00 + 11)
+#define	AT91_PIN_PA12	(0x00 + 12)
+#define	AT91_PIN_PA13	(0x00 + 13)
+#define	AT91_PIN_PA14	(0x00 + 14)
+#define	AT91_PIN_PA15	(0x00 + 15)
+#define	AT91_PIN_PA16	(0x00 + 16)
+#define	AT91_PIN_PA17	(0x00 + 17)
+#define	AT91_PIN_PA18	(0x00 + 18)
+#define	AT91_PIN_PA19	(0x00 + 19)
+#define	AT91_PIN_PA20	(0x00 + 20)
+#define	AT91_PIN_PA21	(0x00 + 21)
+#define	AT91_PIN_PA22	(0x00 + 22)
+#define	AT91_PIN_PA23	(0x00 + 23)
+#define	AT91_PIN_PA24	(0x00 + 24)
+#define	AT91_PIN_PA25	(0x00 + 25)
+#define	AT91_PIN_PA26	(0x00 + 26)
+#define	AT91_PIN_PA27	(0x00 + 27)
+#define	AT91_PIN_PA28	(0x00 + 28)
+#define	AT91_PIN_PA29	(0x00 + 29)
+#define	AT91_PIN_PA30	(0x00 + 30)
+#define	AT91_PIN_PA31	(0x00 + 31)
+
+#define	AT91_PIN_PB0	(0x20 + 0)
+#define	AT91_PIN_PB1	(0x20 + 1)
+#define	AT91_PIN_PB2	(0x20 + 2)
+#define	AT91_PIN_PB3	(0x20 + 3)
+#define	AT91_PIN_PB4	(0x20 + 4)
+#define	AT91_PIN_PB5	(0x20 + 5)
+#define	AT91_PIN_PB6	(0x20 + 6)
+#define	AT91_PIN_PB7	(0x20 + 7)
+#define	AT91_PIN_PB8	(0x20 + 8)
+#define	AT91_PIN_PB9	(0x20 + 9)
+#define	AT91_PIN_PB10	(0x20 + 10)
+#define	AT91_PIN_PB11	(0x20 + 11)
+#define	AT91_PIN_PB12	(0x20 + 12)
+#define	AT91_PIN_PB13	(0x20 + 13)
+#define	AT91_PIN_PB14	(0x20 + 14)
+#define	AT91_PIN_PB15	(0x20 + 15)
+#define	AT91_PIN_PB16	(0x20 + 16)
+#define	AT91_PIN_PB17	(0x20 + 17)
+#define	AT91_PIN_PB18	(0x20 + 18)
+#define	AT91_PIN_PB19	(0x20 + 19)
+#define	AT91_PIN_PB20	(0x20 + 20)
+#define	AT91_PIN_PB21	(0x20 + 21)
+#define	AT91_PIN_PB22	(0x20 + 22)
+#define	AT91_PIN_PB23	(0x20 + 23)
+#define	AT91_PIN_PB24	(0x20 + 24)
+#define	AT91_PIN_PB25	(0x20 + 25)
+#define	AT91_PIN_PB26	(0x20 + 26)
+#define	AT91_PIN_PB27	(0x20 + 27)
+#define	AT91_PIN_PB28	(0x20 + 28)
+#define	AT91_PIN_PB29	(0x20 + 29)
+#define	AT91_PIN_PB30	(0x20 + 30)
+#define	AT91_PIN_PB31	(0x20 + 31)
+
+#define	AT91_PIN_PC0	(0x40 + 0)
+#define	AT91_PIN_PC1	(0x40 + 1)
+#define	AT91_PIN_PC2	(0x40 + 2)
+#define	AT91_PIN_PC3	(0x40 + 3)
+#define	AT91_PIN_PC4	(0x40 + 4)
+#define	AT91_PIN_PC5	(0x40 + 5)
+#define	AT91_PIN_PC6	(0x40 + 6)
+#define	AT91_PIN_PC7	(0x40 + 7)
+#define	AT91_PIN_PC8	(0x40 + 8)
+#define	AT91_PIN_PC9	(0x40 + 9)
+#define	AT91_PIN_PC10	(0x40 + 10)
+#define	AT91_PIN_PC11	(0x40 + 11)
+#define	AT91_PIN_PC12	(0x40 + 12)
+#define	AT91_PIN_PC13	(0x40 + 13)
+#define	AT91_PIN_PC14	(0x40 + 14)
+#define	AT91_PIN_PC15	(0x40 + 15)
+#define	AT91_PIN_PC16	(0x40 + 16)
+#define	AT91_PIN_PC17	(0x40 + 17)
+#define	AT91_PIN_PC18	(0x40 + 18)
+#define	AT91_PIN_PC19	(0x40 + 19)
+#define	AT91_PIN_PC20	(0x40 + 20)
+#define	AT91_PIN_PC21	(0x40 + 21)
+#define	AT91_PIN_PC22	(0x40 + 22)
+#define	AT91_PIN_PC23	(0x40 + 23)
+#define	AT91_PIN_PC24	(0x40 + 24)
+#define	AT91_PIN_PC25	(0x40 + 25)
+#define	AT91_PIN_PC26	(0x40 + 26)
+#define	AT91_PIN_PC27	(0x40 + 27)
+#define	AT91_PIN_PC28	(0x40 + 28)
+#define	AT91_PIN_PC29	(0x40 + 29)
+#define	AT91_PIN_PC30	(0x40 + 30)
+#define	AT91_PIN_PC31	(0x40 + 31)
+
+#define	AT91_PIN_PD0	(0x60 + 0)
+#define	AT91_PIN_PD1	(0x60 + 1)
+#define	AT91_PIN_PD2	(0x60 + 2)
+#define	AT91_PIN_PD3	(0x60 + 3)
+#define	AT91_PIN_PD4	(0x60 + 4)
+#define	AT91_PIN_PD5	(0x60 + 5)
+#define	AT91_PIN_PD6	(0x60 + 6)
+#define	AT91_PIN_PD7	(0x60 + 7)
+#define	AT91_PIN_PD8	(0x60 + 8)
+#define	AT91_PIN_PD9	(0x60 + 9)
+#define	AT91_PIN_PD10	(0x60 + 10)
+#define	AT91_PIN_PD11	(0x60 + 11)
+#define	AT91_PIN_PD12	(0x60 + 12)
+#define	AT91_PIN_PD13	(0x60 + 13)
+#define	AT91_PIN_PD14	(0x60 + 14)
+#define	AT91_PIN_PD15	(0x60 + 15)
+#define	AT91_PIN_PD16	(0x60 + 16)
+#define	AT91_PIN_PD17	(0x60 + 17)
+#define	AT91_PIN_PD18	(0x60 + 18)
+#define	AT91_PIN_PD19	(0x60 + 19)
+#define	AT91_PIN_PD20	(0x60 + 20)
+#define	AT91_PIN_PD21	(0x60 + 21)
+#define	AT91_PIN_PD22	(0x60 + 22)
+#define	AT91_PIN_PD23	(0x60 + 23)
+#define	AT91_PIN_PD24	(0x60 + 24)
+#define	AT91_PIN_PD25	(0x60 + 25)
+#define	AT91_PIN_PD26	(0x60 + 26)
+#define	AT91_PIN_PD27	(0x60 + 27)
+#define	AT91_PIN_PD28	(0x60 + 28)
+#define	AT91_PIN_PD29	(0x60 + 29)
+#define	AT91_PIN_PD30	(0x60 + 30)
+#define	AT91_PIN_PD31	(0x60 + 31)
+
+#define	AT91_PIN_PE0	(0x80 + 0)
+#define	AT91_PIN_PE1	(0x80 + 1)
+#define	AT91_PIN_PE2	(0x80 + 2)
+#define	AT91_PIN_PE3	(0x80 + 3)
+#define	AT91_PIN_PE4	(0x80 + 4)
+#define	AT91_PIN_PE5	(0x80 + 5)
+#define	AT91_PIN_PE6	(0x80 + 6)
+#define	AT91_PIN_PE7	(0x80 + 7)
+#define	AT91_PIN_PE8	(0x80 + 8)
+#define	AT91_PIN_PE9	(0x80 + 9)
+#define	AT91_PIN_PE10	(0x80 + 10)
+#define	AT91_PIN_PE11	(0x80 + 11)
+#define	AT91_PIN_PE12	(0x80 + 12)
+#define	AT91_PIN_PE13	(0x80 + 13)
+#define	AT91_PIN_PE14	(0x80 + 14)
+#define	AT91_PIN_PE15	(0x80 + 15)
+#define	AT91_PIN_PE16	(0x80 + 16)
+#define	AT91_PIN_PE17	(0x80 + 17)
+#define	AT91_PIN_PE18	(0x80 + 18)
+#define	AT91_PIN_PE19	(0x80 + 19)
+#define	AT91_PIN_PE20	(0x80 + 20)
+#define	AT91_PIN_PE21	(0x80 + 21)
+#define	AT91_PIN_PE22	(0x80 + 22)
+#define	AT91_PIN_PE23	(0x80 + 23)
+#define	AT91_PIN_PE24	(0x80 + 24)
+#define	AT91_PIN_PE25	(0x80 + 25)
+#define	AT91_PIN_PE26	(0x80 + 26)
+#define	AT91_PIN_PE27	(0x80 + 27)
+#define	AT91_PIN_PE28	(0x80 + 28)
+#define	AT91_PIN_PE29	(0x80 + 29)
+#define	AT91_PIN_PE30	(0x80 + 30)
+#define	AT91_PIN_PE31	(0x80 + 31)
 
 #ifndef __ASSEMBLY__
 /* setup setup routines, called from board init or driver probe() */
@@ -215,8 +213,8 @@ extern void at91_gpio_resume(void);
 
 #include <asm/errno.h>
 
-#define gpio_to_irq(gpio) (gpio)
-#define irq_to_gpio(irq)  (irq)
+#define gpio_to_irq(gpio) (gpio + NR_AIC_IRQS)
+#define irq_to_gpio(irq)  (irq - NR_AIC_IRQS)
 
 #endif	/* __ASSEMBLY__ */
 

arch/arm/mach-at91/include/mach/hardware.h

@@ -16,6 +16,12 @@
 
 #include <asm/sizes.h>
 
+/* DBGU base */
+/* rm9200, 9260/9g20, 9261/9g10, 9rl */
+#define AT91_BASE_DBGU0	0xfffff200
+/* 9263, 9g45, cap9 */
+#define AT91_BASE_DBGU1	0xffffee00
+
 #if defined(CONFIG_ARCH_AT91RM9200)
 #include <mach/at91rm9200.h>
 #elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20)
@@ -51,6 +57,12 @@
 #define AT91_BASE_SYS	0xffffc000
 #endif
 
+/*
+ * On all at91 have the Advanced Interrupt Controller starts at address
+ * 0xfffff000
+ */
+#define AT91_AIC	0xfffff000
+
 /*
  * Peripheral identifiers/interrupts.
  */

arch/arm/mach-at91/include/mach/irqs.h

@@ -31,7 +31,7 @@
  * Acknowledge interrupt with AIC after interrupt has been handled.
  *   (by kernel/irq.c)
  */
-#define irq_finish(irq) do { at91_sys_write(AT91_AIC_EOICR, 0); } while (0)
+#define irq_finish(irq) do { at91_aic_write(AT91_AIC_EOICR, 0); } while (0)
 
 
 /*

arch/arm/mach-at91/include/mach/timex.h

@@ -23,70 +23,15 @@
 
 #include <mach/hardware.h>
 
-#if defined(CONFIG_ARCH_AT91RM9200)
+#ifdef CONFIG_ARCH_AT91X40
 
-#define CLOCK_TICK_RATE		(AT91_SLOW_CLOCK)
-
-#elif defined(CONFIG_ARCH_AT91SAM9260)
-
-#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260)
-#define AT91SAM9_MASTER_CLOCK	90000000
-#else
-#define AT91SAM9_MASTER_CLOCK	99300000
-#endif
-
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9261)
-
-#define AT91SAM9_MASTER_CLOCK	99300000
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G10)
-
-#define AT91SAM9_MASTER_CLOCK	133000000
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9263)
-
-#if defined(CONFIG_MACH_USB_A9263)
-#define AT91SAM9_MASTER_CLOCK	90000000
-#else
-#define AT91SAM9_MASTER_CLOCK	99959500
-#endif
-
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9RL)
-
-#define AT91SAM9_MASTER_CLOCK	100000000
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G20)
+#define AT91X40_MASTER_CLOCK	40000000
+#define CLOCK_TICK_RATE		(AT91X40_MASTER_CLOCK)
 
-#if defined(CONFIG_MACH_USB_A9G20)
-#define AT91SAM9_MASTER_CLOCK	133000000
 #else
-#define AT91SAM9_MASTER_CLOCK	132096000
-#endif
-
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91SAM9G45)
 
-#define AT91SAM9_MASTER_CLOCK	133333333
-#define CLOCK_TICK_RATE		(AT91SAM9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91CAP9)
-
-#define AT91CAP9_MASTER_CLOCK	100000000
-#define CLOCK_TICK_RATE		(AT91CAP9_MASTER_CLOCK/16)
-
-#elif defined(CONFIG_ARCH_AT91X40)
-
-#define AT91X40_MASTER_CLOCK	40000000
-#define CLOCK_TICK_RATE		(AT91X40_MASTER_CLOCK)
+#define CLOCK_TICK_RATE		12345678
 
 #endif
 
-#endif
+#endif /* __ASM_ARCH_TIMEX_H */

arch/arm/mach-at91/include/mach/uncompress.h

@@ -24,8 +24,10 @@
 #include <linux/io.h>
 #include <linux/atmel_serial.h>
 
-#if defined(CONFIG_AT91_EARLY_DBGU)
-#define UART_OFFSET (AT91_DBGU + AT91_BASE_SYS)
+#if defined(CONFIG_AT91_EARLY_DBGU0)
+#define UART_OFFSET AT91_BASE_DBGU0
+#elif defined(CONFIG_AT91_EARLY_DBGU1)
+#define UART_OFFSET AT91_BASE_DBGU1
 #elif defined(CONFIG_AT91_EARLY_USART0)
 #define UART_OFFSET AT91_USART0
 #elif defined(CONFIG_AT91_EARLY_USART1)

arch/arm/mach-at91/irq.c

@@ -33,17 +33,18 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/map.h>
 
+void __iomem *at91_aic_base;
 
 static void at91_aic_mask_irq(struct irq_data *d)
 {
 	/* Disable interrupt on AIC */
-	at91_sys_write(AT91_AIC_IDCR, 1 << d->irq);
+	at91_aic_write(AT91_AIC_IDCR, 1 << d->irq);
 }
 
 static void at91_aic_unmask_irq(struct irq_data *d)
 {
 	/* Enable interrupt on AIC */
-	at91_sys_write(AT91_AIC_IECR, 1 << d->irq);
+	at91_aic_write(AT91_AIC_IECR, 1 << d->irq);
 }
 
 unsigned int at91_extern_irq;
@@ -77,8 +78,8 @@ static int at91_aic_set_type(struct irq_data *d, unsigned type)
 		return -EINVAL;
 	}
 
-	smr = at91_sys_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE;
-	at91_sys_write(AT91_AIC_SMR(d->irq), smr | srctype);
+	smr = at91_aic_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE;
+	at91_aic_write(AT91_AIC_SMR(d->irq), smr | srctype);
 	return 0;
 }
 
@@ -102,15 +103,15 @@ static int at91_aic_set_wake(struct irq_data *d, unsigned value)
 
 void at91_irq_suspend(void)
 {
-	backups = at91_sys_read(AT91_AIC_IMR);
-	at91_sys_write(AT91_AIC_IDCR, backups);
-	at91_sys_write(AT91_AIC_IECR, wakeups);
+	backups = at91_aic_read(AT91_AIC_IMR);
+	at91_aic_write(AT91_AIC_IDCR, backups);
+	at91_aic_write(AT91_AIC_IECR, wakeups);
 }
 
 void at91_irq_resume(void)
 {
-	at91_sys_write(AT91_AIC_IDCR, wakeups);
-	at91_sys_write(AT91_AIC_IECR, backups);
+	at91_aic_write(AT91_AIC_IDCR, wakeups);
+	at91_aic_write(AT91_AIC_IECR, backups);
 }
 
 #else
@@ -133,34 +134,39 @@ void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS])
 {
 	unsigned int i;
 
+	at91_aic_base = ioremap(AT91_AIC, 512);
+
+	if (!at91_aic_base)
+		panic("Impossible to ioremap AT91_AIC\n");
+
 	/*
 	 * The IVR is used by macro get_irqnr_and_base to read and verify.
 	 * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred.
 	 */
 	for (i = 0; i < NR_AIC_IRQS; i++) {
 		/* Put irq number in Source Vector Register: */
-		at91_sys_write(AT91_AIC_SVR(i), i);
+		at91_aic_write(AT91_AIC_SVR(i), i);
 		/* Active Low interrupt, with the specified priority */
-		at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
+		at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]);
 
 		irq_set_chip_and_handler(i, &at91_aic_chip, handle_level_irq);
 		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
 
 		/* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */
 		if (i < 8)
-			at91_sys_write(AT91_AIC_EOICR, 0);
+			at91_aic_write(AT91_AIC_EOICR, 0);
 	}
 
 	/*
 	 * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS
 	 * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU
 	 */
-	at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS);
+	at91_aic_write(AT91_AIC_SPU, NR_AIC_IRQS);
 
 	/* No debugging in AIC: Debug (Protect) Control Register */
-	at91_sys_write(AT91_AIC_DCR, 0);
+	at91_aic_write(AT91_AIC_DCR, 0);
 
 	/* Disable and clear all interrupts initially */
-	at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF);
-	at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF);
+	at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF);
+	at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF);
 }

arch/arm/mach-at91/pm.c

@@ -34,7 +34,7 @@
 /*
  * Show the reason for the previous system reset.
  */
-#if defined(AT91_SHDWC)
+#if defined(AT91_RSTC)
 
 #include <mach/at91_rstc.h>
 #include <mach/at91_shdwc.h>
@@ -58,8 +58,11 @@ static void __init show_reset_status(void)
 	char *reason, *r2 = reset;
 	u32 reset_type, wake_type;
 
+	if (!at91_shdwc_base)
+		return;
+
 	reset_type = at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP;
-	wake_type = at91_sys_read(AT91_SHDW_SR);
+	wake_type = at91_shdwc_read(AT91_SHDW_SR);
 
 	switch (reset_type) {
 	case AT91_RSTC_RSTTYP_GENERAL:
@@ -215,7 +218,7 @@ static int at91_pm_enter(suspend_state_t state)
 					| (1 << AT91_ID_FIQ)
 					| (1 << AT91_ID_SYS)
 					| (at91_extern_irq))
-				& at91_sys_read(AT91_AIC_IMR),
+				& at91_aic_read(AT91_AIC_IMR),
 			state);
 
 	switch (state) {
@@ -283,7 +286,7 @@ static int at91_pm_enter(suspend_state_t state)
 	}
 
 	pr_debug("AT91: PM - wakeup %08x\n",
-			at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR));
+			at91_aic_read(AT91_AIC_IPR) & at91_aic_read(AT91_AIC_IMR));
 
 error:
 	target_state = PM_SUSPEND_ON;

arch/arm/mach-at91/sam9_smc.c

@@ -10,38 +10,58 @@
 
 #include <linux/module.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 
 #include <mach/at91sam9_smc.h>
 
 #include "sam9_smc.h"
 
-void __init sam9_smc_configure(int cs, struct sam9_smc_config* config)
+
+#define AT91_SMC_CS(id, n)	(smc_base_addr[id] + ((n) * 0x10))
+
+static void __iomem *smc_base_addr[2];
+
+static void __init sam9_smc_cs_configure(void __iomem *base, struct sam9_smc_config* config)
 {
+
 	/* Setup register */
-	at91_sys_write(AT91_SMC_SETUP(cs),
-		  AT91_SMC_NWESETUP_(config->nwe_setup)
-		| AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
-		| AT91_SMC_NRDSETUP_(config->nrd_setup)
-		| AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup)
-	);
+	__raw_writel(AT91_SMC_NWESETUP_(config->nwe_setup)
+		   | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup)
+		   | AT91_SMC_NRDSETUP_(config->nrd_setup)
+		   | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup),
+		   base + AT91_SMC_SETUP);
 
 	/* Pulse register */
-	at91_sys_write(AT91_SMC_PULSE(cs),
-		  AT91_SMC_NWEPULSE_(config->nwe_pulse)
-		| AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
-                | AT91_SMC_NRDPULSE_(config->nrd_pulse)
-		| AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse)
-	);
+	__raw_writel(AT91_SMC_NWEPULSE_(config->nwe_pulse)
+		   | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse)
+		   | AT91_SMC_NRDPULSE_(config->nrd_pulse)
+		   | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse),
+		   base + AT91_SMC_PULSE);
 
 	/* Cycle register */
-	at91_sys_write(AT91_SMC_CYCLE(cs),
-		  AT91_SMC_NWECYCLE_(config->write_cycle)
-		| AT91_SMC_NRDCYCLE_(config->read_cycle)
-	);
+	__raw_writel(AT91_SMC_NWECYCLE_(config->write_cycle)
+		   | AT91_SMC_NRDCYCLE_(config->read_cycle),
+		   base + AT91_SMC_CYCLE);
 
 	/* Mode register */
-	at91_sys_write(AT91_SMC_MODE(cs),
-		  config->mode
-		| AT91_SMC_TDF_(config->tdf_cycles)
-	);
+	__raw_writel(config->mode
+		   | AT91_SMC_TDF_(config->tdf_cycles),
+		   base + AT91_SMC_MODE);
+}
+
+void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config)
+{
+	sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config);
+}
+
+void __init at91sam9_ioremap_smc(int id, u32 addr)
+{
+	if (id > 1) {
+		pr_warn("%s: id > 2\n", __func__);
+		return;
+	}
+	smc_base_addr[id] = ioremap(addr, 512);
+	if (!smc_base_addr[id])
+		pr_warn("Impossible to ioremap smc.%d 0x%x\n", id, addr);
 }

arch/arm/mach-at91/sam9_smc.h

@@ -30,4 +30,5 @@ struct sam9_smc_config {
 	u8 tdf_cycles:4;
 };
 
-extern void __init sam9_smc_configure(int cs, struct sam9_smc_config* config);
+extern void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config);
+extern void __init at91sam9_ioremap_smc(int id, u32 addr);

arch/arm/mach-at91/setup.c

@@ -8,6 +8,7 @@
 #include <linux/module.h>
 #include <linux/io.h>
 #include <linux/mm.h>
+#include <linux/pm.h>
 
 #include <asm/mach/map.h>
 
@@ -15,6 +16,7 @@
 #include <mach/cpu.h>
 #include <mach/at91_dbgu.h>
 #include <mach/at91_pmc.h>
+#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
@@ -73,9 +75,6 @@ static struct map_desc at91_io_desc __initdata = {
 	.type		= MT_DEVICE,
 };
 
-#define AT91_DBGU0	0xfffff200
-#define AT91_DBGU1	0xffffee00
-
 static void __init soc_detect(u32 dbgu_base)
 {
 	u32 cidr, socid;
@@ -248,9 +247,9 @@ void __init at91_map_io(void)
 	at91_soc_initdata.type = AT91_SOC_NONE;
 	at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
 
-	soc_detect(AT91_DBGU0);
+	soc_detect(AT91_BASE_DBGU0);
 	if (!at91_soc_is_detected())
-		soc_detect(AT91_DBGU1);
+		soc_detect(AT91_BASE_DBGU1);
 
 	if (!at91_soc_is_detected())
 		panic("AT91: Impossible to detect the SOC type");
@@ -267,8 +266,25 @@ void __init at91_map_io(void)
 		at91_boot_soc.map_io();
 }
 
+void __iomem *at91_shdwc_base = NULL;
+
+static void at91sam9_poweroff(void)
+{
+	at91_shdwc_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
+}
+
+void __init at91_ioremap_shdwc(u32 base_addr)
+{
+	at91_shdwc_base = ioremap(base_addr, 16);
+	if (!at91_shdwc_base)
+		panic("Impossible to ioremap at91_shdwc_base\n");
+	pm_power_off = at91sam9_poweroff;
+}
+
 void __init at91_initialize(unsigned long main_clock)
 {
+	at91_boot_soc.ioremap_registers();
+
 	/* Init clock subsystem */
 	at91_clock_init(main_clock);
 

arch/arm/mach-at91/soc.h

@@ -7,6 +7,7 @@
 struct at91_init_soc {
 	unsigned int *default_irq_priority;
 	void (*map_io)(void);
+	void (*ioremap_registers)(void);
 	void (*register_clocks)(void);
 	void (*init)(void);
 };

arch/arm/mach-davinci/include/mach/dm646x.h

@@ -16,6 +16,7 @@
 #include <linux/i2c.h>
 #include <linux/videodev2.h>
 #include <linux/davinci_emac.h>
+#include <media/davinci/vpif_types.h>
 
 #define DM646X_EMAC_BASE		(0x01C80000)
 #define DM646X_EMAC_MDIO_BASE		(DM646X_EMAC_BASE + 0x4000)
@@ -34,58 +35,6 @@ int __init dm646x_init_edma(struct edma_rsv_info *rsv);
 
 void dm646x_video_init(void);
 
-enum vpif_if_type {
-	VPIF_IF_BT656,
-	VPIF_IF_BT1120,
-	VPIF_IF_RAW_BAYER
-};
-
-struct vpif_interface {
-	enum vpif_if_type if_type;
-	unsigned hd_pol:1;
-	unsigned vd_pol:1;
-	unsigned fid_pol:1;
-};
-
-struct vpif_subdev_info {
-	const char *name;
-	struct i2c_board_info board_info;
-	u32 input;
-	u32 output;
-	unsigned can_route:1;
-	struct vpif_interface vpif_if;
-};
-
-struct vpif_display_config {
-	int (*set_clock)(int, int);
-	struct vpif_subdev_info *subdevinfo;
-	int subdev_count;
-	const char **output;
-	int output_count;
-	const char *card_name;
-};
-
-struct vpif_input {
-	struct v4l2_input input;
-	const char *subdev_name;
-};
-
-#define VPIF_CAPTURE_MAX_CHANNELS	2
-
-struct vpif_capture_chan_config {
-	const struct vpif_input *inputs;
-	int input_count;
-};
-
-struct vpif_capture_config {
-	int (*setup_input_channel_mode)(int);
-	int (*setup_input_path)(int, const char *);
-	struct vpif_capture_chan_config chan_config[VPIF_CAPTURE_MAX_CHANNELS];
-	struct vpif_subdev_info *subdev_info;
-	int subdev_count;
-	const char *card_name;
-};
-
 void dm646x_setup_vpif(struct vpif_display_config *,
 		       struct vpif_capture_config *);
 

arch/arm/mach-msm/Kconfig

@@ -13,7 +13,6 @@ config ARCH_MSM7X00A
 	select CPU_V6
 	select GPIO_MSM_V1
 	select MSM_PROC_COMM
-	select HAS_MSM_DEBUG_UART_PHYS
 
 config ARCH_MSM7X30
 	bool "MSM7x30"
@@ -25,7 +24,6 @@ config ARCH_MSM7X30
 	select MSM_GPIOMUX
 	select GPIO_MSM_V1
 	select MSM_PROC_COMM
-	select HAS_MSM_DEBUG_UART_PHYS
 
 config ARCH_QSD8X50
 	bool "QSD8X50"
@@ -37,7 +35,6 @@ config ARCH_QSD8X50
 	select MSM_GPIOMUX
 	select GPIO_MSM_V1
 	select MSM_PROC_COMM
-	select HAS_MSM_DEBUG_UART_PHYS
 
 config ARCH_MSM8X60
 	bool "MSM8X60"
@@ -63,6 +60,9 @@ config ARCH_MSM8960
 
 endchoice
 
+config MSM_HAS_DEBUG_UART_HS
+	bool
+
 config MSM_SOC_REV_A
 	bool
 config  ARCH_MSM_SCORPIONMP
@@ -74,9 +74,6 @@ config  ARCH_MSM_ARM11
 config  ARCH_MSM_SCORPION
 	bool
 
-config HAS_MSM_DEBUG_UART_PHYS
-	bool
-
 config  MSM_VIC
 	bool
 
@@ -153,32 +150,6 @@ config MACH_MSM8960_RUMI3
 
 endmenu
 
-config MSM_DEBUG_UART
-	int
-	default 1 if MSM_DEBUG_UART1
-	default 2 if MSM_DEBUG_UART2
-	default 3 if MSM_DEBUG_UART3
-
-if HAS_MSM_DEBUG_UART_PHYS
-choice
-	prompt "Debug UART"
-
-	default MSM_DEBUG_UART_NONE
-
-	config MSM_DEBUG_UART_NONE
-		bool "None"
-
-	config MSM_DEBUG_UART1
-		bool "UART1"
-
-	config MSM_DEBUG_UART2
-		bool "UART2"
-
-	config MSM_DEBUG_UART3
-		bool "UART3"
-endchoice
-endif
-
 config MSM_SMD_PKG3
 	bool
 

arch/arm/mach-msm/include/mach/debug-macro.S

@@ -1,6 +1,7 @@
-/* arch/arm/mach-msm7200/include/mach/debug-macro.S
+/*
  *
  * Copyright (C) 2007 Google, Inc.
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
  * Author: Brian Swetland <swetland@google.com>
  *
  * This software is licensed under the terms of the GNU General Public
@@ -14,40 +15,52 @@
  *
  */
 
-
-
 #include <mach/hardware.h>
 #include <mach/msm_iomap.h>
 
-#if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE)
 	.macro	addruart, rp, rv, tmp
+#ifdef MSM_DEBUG_UART_PHYS
 	ldr	\rp, =MSM_DEBUG_UART_PHYS
 	ldr	\rv, =MSM_DEBUG_UART_BASE
+#endif
 	.endm
 
-	.macro	senduart,rd,rx
+	.macro	senduart, rd, rx
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+	@ Write the 1 character to UARTDM_TF
+	str	\rd, [\rx, #0x70]
+#else
 	teq	\rx, #0
 	strne	\rd, [\rx, #0x0C]
+#endif
 	.endm
 
-	.macro	waituart,rd,rx
+	.macro	waituart, rd, rx
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+	@ check for TX_EMT in UARTDM_SR
+	ldr	\rd, [\rx, #0x08]
+	tst	\rd, #0x08
+	bne	1002f
+	@ wait for TXREADY in UARTDM_ISR
+1001:	ldr	\rd, [\rx, #0x14]
+	tst	\rd, #0x80
+	beq 	1001b
+1002:
+	@ Clear TX_READY by writing to the UARTDM_CR register
+	mov	\rd, #0x300
+	str	\rd, [\rx, #0x10]
+	@ Write 0x1 to NCF register
+	mov 	\rd, #0x1
+	str	\rd, [\rx, #0x40]
+	@ UARTDM reg. Read to induce delay
+	ldr	\rd, [\rx, #0x08]
+#else
 	@ wait for TX_READY
 1001:	ldr	\rd, [\rx, #0x08]
 	tst	\rd, #0x04
 	beq	1001b
-	.endm
-#else
-	.macro  addruart, rp, rv, tmp
-	mov	\rv, #0xff000000
-	orr	\rv, \rv, #0x00f00000
-	.endm
-
-	.macro	senduart,rd,rx
-	.endm
-
-	.macro	waituart,rd,rx
-	.endm
 #endif
+	.endm
 
-	.macro	busyuart,rd,rx
+	.macro	busyuart, rd, rx
 	.endm

arch/arm/mach-msm/include/mach/msm_iomap-7x00.h

@@ -78,18 +78,6 @@
 #define MSM_UART3_PHYS        0xA9C00000
 #define MSM_UART3_SIZE        SZ_4K
 
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE   0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS   MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS   MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS   MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE   SZ_4K
-#endif
-
 #define MSM_SDC1_PHYS         0xA0400000
 #define MSM_SDC1_SIZE         SZ_4K
 

arch/arm/mach-msm/include/mach/msm_iomap-7x30.h

@@ -89,18 +89,6 @@
 #define MSM_UART3_PHYS        0xACC00000
 #define MSM_UART3_SIZE        SZ_4K
 
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE   0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS   MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS   MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS   MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE   SZ_4K
-#endif
-
 #define MSM_MDC_BASE	      IOMEM(0xE0200000)
 #define MSM_MDC_PHYS	      0xAA500000
 #define MSM_MDC_SIZE	      SZ_1M

arch/arm/mach-msm/include/mach/msm_iomap-8960.h

@@ -45,4 +45,9 @@
 #define MSM8960_TMR0_PHYS	0x0208A000
 #define MSM8960_TMR0_SIZE	SZ_4K
 
+#ifdef CONFIG_DEBUG_MSM8960_UART
+#define MSM_DEBUG_UART_BASE	0xE1040000
+#define MSM_DEBUG_UART_PHYS	0x16440000
+#endif
+
 #endif

arch/arm/mach-msm/include/mach/msm_iomap-8x50.h

@@ -83,18 +83,6 @@
 #define MSM_UART3_PHYS        0xA9C00000
 #define MSM_UART3_SIZE        SZ_4K
 
-#ifdef CONFIG_MSM_DEBUG_UART
-#define MSM_DEBUG_UART_BASE   0xE1000000
-#if CONFIG_MSM_DEBUG_UART == 1
-#define MSM_DEBUG_UART_PHYS   MSM_UART1_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 2
-#define MSM_DEBUG_UART_PHYS   MSM_UART2_PHYS
-#elif CONFIG_MSM_DEBUG_UART == 3
-#define MSM_DEBUG_UART_PHYS   MSM_UART3_PHYS
-#endif
-#define MSM_DEBUG_UART_SIZE   SZ_4K
-#endif
-
 #define MSM_MDC_BASE	      IOMEM(0xE0200000)
 #define MSM_MDC_PHYS	      0xAA500000
 #define MSM_MDC_SIZE	      SZ_1M

arch/arm/mach-msm/include/mach/msm_iomap-8x60.h

@@ -62,4 +62,9 @@
 #define MSM8X60_TMR0_PHYS	0x02040000
 #define MSM8X60_TMR0_SIZE	SZ_4K
 
+#ifdef CONFIG_DEBUG_MSM8660_UART
+#define MSM_DEBUG_UART_BASE	0xE1040000
+#define MSM_DEBUG_UART_PHYS	0x19C40000
+#endif
+
 #endif

arch/arm/mach-msm/include/mach/msm_iomap.h

@@ -55,6 +55,18 @@
 
 #include "msm_iomap-8960.h"
 
+#define MSM_DEBUG_UART_SIZE	SZ_4K
+#if defined(CONFIG_DEBUG_MSM_UART1)
+#define MSM_DEBUG_UART_BASE	0xE1000000
+#define MSM_DEBUG_UART_PHYS	MSM_UART1_PHYS
+#elif defined(CONFIG_DEBUG_MSM_UART2)
+#define MSM_DEBUG_UART_BASE	0xE1000000
+#define MSM_DEBUG_UART_PHYS	MSM_UART2_PHYS
+#elif defined(CONFIG_DEBUG_MSM_UART3)
+#define MSM_DEBUG_UART_BASE	0xE1000000
+#define MSM_DEBUG_UART_PHYS	MSM_UART3_PHYS
+#endif
+
 /* Virtual addresses shared across all MSM targets. */
 #define MSM_CSR_BASE		IOMEM(0xE0001000)
 #define MSM_QGIC_DIST_BASE	IOMEM(0xF0000000)

arch/arm/mach-msm/include/mach/uncompress.h

@@ -1,6 +1,6 @@
-/* arch/arm/mach-msm/include/mach/uncompress.h
- *
+/*
  * Copyright (C) 2007 Google, Inc.
+ * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -14,17 +14,40 @@
  */
 
 #ifndef __ASM_ARCH_MSM_UNCOMPRESS_H
+#define __ASM_ARCH_MSM_UNCOMPRESS_H
+
+#include <asm/processor.h>
+#include <mach/msm_iomap.h>
+
+#define UART_CSR      (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08))
+#define UART_TF       (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x0c))
 
-#include "hardware.h"
-#include "linux/io.h"
-#include "mach/msm_iomap.h"
+#define UART_DM_SR    (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08)))
+#define UART_DM_CR    (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x10)))
+#define UART_DM_ISR   (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x14)))
+#define UART_DM_NCHAR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x40)))
+#define UART_DM_TF    (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x70)))
 
 static void putc(int c)
 {
 #if defined(MSM_DEBUG_UART_PHYS)
-	unsigned base = MSM_DEBUG_UART_PHYS;
-	while (!(readl(base + 0x08) & 0x04)) ;
-	writel(c, base + 0x0c);
+#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS
+	/*
+	 * Wait for TX_READY to be set; but skip it if we have a
+	 * TX underrun.
+	 */
+	if (UART_DM_SR & 0x08)
+		while (!(UART_DM_ISR & 0x80))
+			cpu_relax();
+
+	UART_DM_CR = 0x300;
+	UART_DM_NCHAR = 0x1;
+	UART_DM_TF = c;
+#else
+	while (!(UART_CSR & 0x04))
+		cpu_relax();
+	UART_TF = c;
+#endif
 #endif
 }
 

arch/arm/mach-msm/io.c

@@ -47,7 +47,8 @@ static struct map_desc msm_io_desc[] __initdata = {
 	MSM_CHIP_DEVICE(GPIO1, MSM7X00),
 	MSM_CHIP_DEVICE(GPIO2, MSM7X00),
 	MSM_DEVICE(CLK_CTL),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+	defined(CONFIG_DEBUG_MSM_UART3)
 	MSM_DEVICE(DEBUG_UART),
 #endif
 #ifdef CONFIG_ARCH_MSM7X30
@@ -84,7 +85,8 @@ static struct map_desc qsd8x50_io_desc[] __initdata = {
 	MSM_DEVICE(SCPLL),
 	MSM_DEVICE(AD5),
 	MSM_DEVICE(MDC),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+	defined(CONFIG_DEBUG_MSM_UART3)
 	MSM_DEVICE(DEBUG_UART),
 #endif
 	{
@@ -109,6 +111,9 @@ static struct map_desc msm8x60_io_desc[] __initdata = {
 	MSM_CHIP_DEVICE(TMR0, MSM8X60),
 	MSM_DEVICE(ACC),
 	MSM_DEVICE(GCC),
+#ifdef CONFIG_DEBUG_MSM8660_UART
+	MSM_DEVICE(DEBUG_UART),
+#endif
 };
 
 void __init msm_map_msm8x60_io(void)
@@ -123,6 +128,9 @@ static struct map_desc msm8960_io_desc[] __initdata = {
 	MSM_CHIP_DEVICE(QGIC_CPU, MSM8960),
 	MSM_CHIP_DEVICE(TMR, MSM8960),
 	MSM_CHIP_DEVICE(TMR0, MSM8960),
+#ifdef CONFIG_DEBUG_MSM8960_UART
+	MSM_DEVICE(DEBUG_UART),
+#endif
 };
 
 void __init msm_map_msm8960_io(void)
@@ -146,7 +154,8 @@ static struct map_desc msm7x30_io_desc[] __initdata = {
 	MSM_DEVICE(SAW),
 	MSM_DEVICE(GCC),
 	MSM_DEVICE(TCSR),
-#ifdef CONFIG_MSM_DEBUG_UART
+#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
+	defined(CONFIG_DEBUG_MSM_UART3)
 	MSM_DEVICE(DEBUG_UART),
 #endif
 	{

arch/arm/mach-msm/platsmp.c

@@ -79,7 +79,7 @@ static __cpuinit void prepare_cold_cpu(unsigned int cpu)
 	ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup),
 				SCM_FLAG_COLDBOOT_CPU1);
 	if (ret == 0) {
-		void *sc1_base_ptr;
+		void __iomem *sc1_base_ptr;
 		sc1_base_ptr = ioremap_nocache(0x00902000, SZ_4K*2);
 		if (sc1_base_ptr) {
 			writel(0, sc1_base_ptr + VDD_SC1_ARRAY_CLAMP_GFS_CTL);

arch/arm/mach-picoxcell/Makefile

@@ -1,3 +1,2 @@
 obj-y	:= common.o
 obj-y	+= time.o
-obj-y	+= io.o