[MIPS] Fix the build error of Wind River PPMC board, rewrite irq code to C

 o Fix the build error Wind River PPMC board caused by the change of
   plat_setup hook interface.
 o Rewrite first level interrupt dispatch code to C.

Signed-off-by: Rongkai.Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/Kconfig

@@ -358,7 +358,7 @@ config MIPS_SEAD
 	  board.
 
 config WR_PPMC
-	bool "Support for Wind River PPMC board"
+	bool "Wind River PPMC board"
 	select IRQ_CPU
 	select BOOT_ELF32
 	select DMA_NONCOHERENT

arch/mips/gt64120/wrppmc/Makefile

@@ -9,6 +9,6 @@
 # Makefile for the Wind River MIPS 4KC PPMC Eval Board
 #
 
-obj-y	+= int-handler.o irq.o reset.o setup.o time.o pci.o
+obj-y += irq.o reset.o setup.o time.o pci.o
 
 EXTRA_AFLAGS := $(CFLAGS)

arch/mips/gt64120/wrppmc/int-handler.S

@@ -1,59 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 1995, 1996, 1997, 2003 by Ralf Baechle
- * Copyright (C) Wind River System Inc. Rongkai.Zhan <rongkai.zhan@windriver.com>
- */
-#include <asm/asm.h>
-#include <asm/mipsregs.h>
-#include <asm/addrspace.h>
-#include <asm/regdef.h>
-#include <asm/stackframe.h>
-#include <asm/mach-wrppmc/mach-gt64120.h>
-
-	.align	5
-	.set	noat
-NESTED(handle_IRQ, PT_SIZE, sp)
-	SAVE_ALL
-	CLI				# Important: mark KERNEL mode !
-	.set	at
-
-	mfc0	t0, CP0_CAUSE		# get pending interrupts
-	mfc0	t1, CP0_STATUS		# get enabled interrupts
-	and	t0, t0, t1		# get allowed interrupts
-	andi	t0, t0, 0xFF00
-	beqz	t0, 1f
-	move	a1, sp			# Prepare 'struct pt_regs *regs' pointer
-
-	andi	t1, t0, CAUSEF_IP7	# CPU Compare/Count internal timer
-	bnez	t1, handle_cputimer_irq
-	andi	t1, t0, CAUSEF_IP6	# UART 16550 port
-	bnez	t1, handle_uart_irq
-	andi	t1, t0, CAUSEF_IP3	# PCI INT_A
-	bnez	t1, handle_pci_intA_irq
-
-	/* wrong alarm or masked ... */
-1:	j	spurious_interrupt
-	nop
-END(handle_IRQ)
-
-	.align	5
-handle_cputimer_irq:
-	li	a0, WRPPMC_MIPS_TIMER_IRQ
-	jal	do_IRQ
-	j	ret_from_irq
-
-	.align	5
-handle_uart_irq:
-	li	a0, WRPPMC_UART16550_IRQ
-	jal	do_IRQ
-	j	ret_from_irq
-
-	.align	5
-handle_pci_intA_irq:
-	li	a0, WRPPMC_PCI_INTA_IRQ
-	jal	do_IRQ
-	j	ret_from_irq
-

arch/mips/gt64120/wrppmc/irq.c

@@ -30,7 +30,19 @@
 #include <asm/irq_cpu.h>
 #include <asm/gt64120.h>
 
-extern asmlinkage void handle_IRQ(void);
+asmlinkage void plat_irq_dispatch(struct pt_regs *regs)
+{
+	unsigned int pending = read_c0_status() & read_c0_cause();
+
+	if (pending & STATUSF_IP7)
+		do_IRQ(WRPPMC_MIPS_TIMER_IRQ, regs);	/* CPU Compare/Count internal timer */
+	else if (pending & STATUSF_IP6)
+		do_IRQ(WRPPMC_UART16550_IRQ, regs);	/* UART 16550 port */
+	else if (pending & STATUSF_IP3)
+		do_IRQ(WRPPMC_PCI_INTA_IRQ, regs);	/* PCI INT_A */
+	else
+		spurious_interrupt(regs);
+}
 
 /**
  * Initialize GT64120 Interrupt Controller
@@ -53,9 +65,6 @@ void __init arch_init_irq(void)
 	/* enable all CPU interrupt bits. */
 	set_c0_status(ST0_IM);	/* IE bit is still 0 */
 
-	/* Install MIPS Interrupt Trap Vector */
-	set_except_vector(0, handle_IRQ);
-
 	/* IRQ 0 - 7 are for MIPS common irq_cpu controller */
 	mips_cpu_irq_init(0);
 

arch/mips/gt64120/wrppmc/setup.c

@@ -125,7 +125,7 @@ static void wrppmc_setup_serial(void)
 }
 #endif
 
-void __init plat_setup(void)
+void __init plat_mem_setup(void)
 {
 	extern void wrppmc_time_init(void);
 	extern void wrppmc_timer_setup(struct irqaction *);