Merge tag 'v3.8-rc7' into x86/asm

Merge in the updates to head_32.S from the previous urgent branch, as
upcoming patches will make further changes.

Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Documentation/device-mapper/dm-raid.txt

@@ -141,3 +141,4 @@ Version History
 1.2.0	Handle creation of arrays that contain failed devices.
 1.3.0	Added support for RAID 10
 1.3.1	Allow device replacement/rebuild for RAID 10
+1.3.2   Fix/improve redundancy checking for RAID10

Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -81,7 +81,8 @@ PA31	TXD4
 Required properties for pin configuration node:
 - atmel,pins: 4 integers array, represents a group of pins mux and config
   setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
-  The PERIPH 0 means gpio.
+  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
+  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
 
 Bits used for CONFIG:
 PULL_UP		(1 << 0): indicate this pin need a pull up.
@@ -126,7 +127,7 @@ pinctrl@fffff400 {
 		pinctrl_dbgu: dbgu-0 {
 			atmel,pins =
 				<1 14 0x1 0x0	/* PB14 periph A */
-				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
+				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
 		};
 	};
 };

Documentation/hid/hid-sensor.txt

@@ -2438,7 +2438,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			real-time workloads.  It can also improve energy
 			efficiency for asymmetric multiprocessors.
 
-	rcu_nocbs_poll	[KNL,BOOT]
+	rcu_nocb_poll	[KNL,BOOT]
 			Rather than requiring that offloaded CPUs
 			(specified by rcu_nocbs= above) explicitly
 			awaken the corresponding "rcuoN" kthreads,

Documentation/x86/boot.txt

@@ -57,6 +57,10 @@ Protocol 2.10:	(Kernel 2.6.31) Added a protocol for relaxed alignment
 Protocol 2.11:	(Kernel 3.6) Added a field for offset of EFI handover
 		protocol entry point.
 
+Protocol 2.12:	(Kernel 3.8) Added the xloadflags field and extension fields
+	 	to struct boot_params for for loading bzImage and ramdisk
+		above 4G in 64bit.
+
 **** MEMORY LAYOUT
 
 The traditional memory map for the kernel loader, used for Image or
@@ -182,7 +186,7 @@ Offset	Proto	Name		Meaning
 0230/4	2.05+	kernel_alignment Physical addr alignment required for kernel
 0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
 0235/1	2.10+	min_alignment	Minimum alignment, as a power of two
-0236/2	N/A	pad3		Unused
+0236/2	2.12+	xloadflags	Boot protocol option flags
 0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
 023C/4	2.07+	hardware_subarch Hardware subarchitecture
 0240/8	2.07+	hardware_subarch_data Subarchitecture-specific data
@@ -582,6 +586,27 @@ Protocol:	2.10+
   misaligned kernel.  Therefore, a loader should typically try each
   power-of-two alignment from kernel_alignment down to this alignment.
 
+Field name:     xloadflags
+Type:           read
+Offset/size:    0x236/2
+Protocol:       2.12+
+
+  This field is a bitmask.
+
+  Bit 0 (read):	XLF_KERNEL_64
+	- If 1, this kernel has the legacy 64-bit entry point at 0x200.
+
+  Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G
+        - If 1, kernel/boot_params/cmdline/ramdisk can be above 4G.
+
+  Bit 2 (read):	XLF_EFI_HANDOVER_32
+	- If 1, the kernel supports the 32-bit EFI handoff entry point
+          given at handover_offset.
+
+  Bit 3 (read): XLF_EFI_HANDOVER_64
+	- If 1, the kernel supports the 64-bit EFI handoff entry point
+          given at handover_offset + 0x200.
+
 Field name:	cmdline_size
 Type:		read
 Offset/size:	0x238/4

Documentation/x86/zero-page.txt

@@ -19,6 +19,9 @@ Offset	Proto	Name		Meaning
 090/010	ALL	hd1_info	hd1 disk parameter, OBSOLETE!!
 0A0/010	ALL	sys_desc_table	System description table (struct sys_desc_table)
 0B0/010	ALL	olpc_ofw_header	OLPC's OpenFirmware CIF and friends
+0C0/004	ALL	ext_ramdisk_image ramdisk_image high 32bits
+0C4/004	ALL	ext_ramdisk_size  ramdisk_size high 32bits
+0C8/004	ALL	ext_cmd_line_ptr  cmd_line_ptr high 32bits
 140/080	ALL	edid_info	Video mode setup (struct edid_info)
 1C0/020	ALL	efi_info	EFI 32 information (struct efi_info)
 1E0/004	ALL	alk_mem_k	Alternative mem check, in KB
@@ -27,6 +30,7 @@ Offset	Proto	Name		Meaning
 1E9/001	ALL	eddbuf_entries	Number of entries in eddbuf (below)
 1EA/001	ALL	edd_mbr_sig_buf_entries	Number of entries in edd_mbr_sig_buffer
 				(below)
+1EF/001	ALL	sentinel	Used to detect broken bootloaders
 290/040	ALL	edd_mbr_sig_buffer EDD MBR signatures
 2D0/A00	ALL	e820_map	E820 memory map table
 				(array of struct e820entry)

MAINTAINERS

@@ -1489,7 +1489,7 @@ AVR32 ARCHITECTURE
 M:	Haavard Skinnemoen <hskinnemoen@gmail.com>
 M:	Hans-Christian Egtvedt <egtvedt@samfundet.no>
 W:	http://www.atmel.com/products/AVR32/
-W:	http://avr32linux.org/
+W:	http://mirror.egtvedt.no/avr32linux.org/
 W:	http://avrfreaks.net/
 S:	Maintained
 F:	arch/avr32/
@@ -2966,7 +2966,7 @@ S:	Maintained
 F:	drivers/net/ethernet/i825xx/eexpress.*
 
 ETHERNET BRIDGE
-M:	Stephen Hemminger <shemminger@vyatta.com>
+M:	Stephen Hemminger <stephen@networkplumber.org>
 L:	bridge@lists.linux-foundation.org
 L:	netdev@vger.kernel.org
 W:	http://www.linuxfoundation.org/en/Net:Bridge
@@ -4905,7 +4905,7 @@ S:	Maintained
 
 MARVELL GIGABIT ETHERNET DRIVERS (skge/sky2)
 M:	Mirko Lindner <mlindner@marvell.com>
-M:	Stephen Hemminger <shemminger@vyatta.com>
+M:	Stephen Hemminger <stephen@networkplumber.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ethernet/marvell/sk*
@@ -5180,7 +5180,7 @@ S:	Supported
 F:	drivers/infiniband/hw/nes/
 
 NETEM NETWORK EMULATOR
-M:	Stephen Hemminger <shemminger@vyatta.com>
+M:	Stephen Hemminger <stephen@networkplumber.org>
 L:	netem@lists.linux-foundation.org
 S:	Maintained
 F:	net/sched/sch_netem.c
@@ -7088,7 +7088,7 @@ F:	include/uapi/sound/
 F:	sound/
 
 SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC)
-M:	Liam Girdwood <lrg@ti.com>
+M:	Liam Girdwood <lgirdwood@gmail.com>
 M:	Mark Brown <broonie@opensource.wolfsonmicro.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)

Makefile

@@ -1,8 +1,8 @@
 VERSION = 3
 PATCHLEVEL = 8
 SUBLEVEL = 0
-EXTRAVERSION = -rc4
-NAME = Terrified Chipmunk
+EXTRAVERSION = -rc7
+NAME = Unicycling Gorilla
 
 # *DOCUMENTATION*
 # To see a list of typical targets execute "make help"

arch/arm/boot/dts/armada-370-db.dts

@@ -26,7 +26,7 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0x00000000 0x20000000>; /* 512 MB */
+		reg = <0x00000000 0x40000000>; /* 1 GB */
 	};
 
 	soc {

arch/arm/boot/dts/armada-xp-mv78230.dtsi

@@ -50,27 +50,25 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <17>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>;
+			interrupts = <87>, <88>, <89>;
 		};
 	};
 };

arch/arm/boot/dts/armada-xp-mv78260.dtsi

@@ -51,39 +51,36 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>, <23>;
+			interrupts = <87>, <88>, <89>, <90>;
 		};
 
 		gpio2: gpio@d0018180 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018180 0x40>,
-			    <0xd0018870 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018180 0x40>;
 			ngpios = <3>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <24>;
+			interrupts = <91>;
 		};
 
 		ethernet@d0034000 {

arch/arm/boot/dts/armada-xp-mv78460.dtsi

@@ -66,39 +66,36 @@
 		};
 
 		gpio0: gpio@d0018100 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018100 0x40>,
-			    <0xd0018800 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018100 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <16>, <17>, <18>, <19>;
+			interrupts = <82>, <83>, <84>, <85>;
 		};
 
 		gpio1: gpio@d0018140 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018140 0x40>,
-			    <0xd0018840 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018140 0x40>;
 			ngpios = <32>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <20>, <21>, <22>, <23>;
+			interrupts = <87>, <88>, <89>, <90>;
 		};
 
 		gpio2: gpio@d0018180 {
-			compatible = "marvell,armadaxp-gpio";
-			reg = <0xd0018180 0x40>,
-			    <0xd0018870 0x30>;
+			compatible = "marvell,orion-gpio";
+			reg = <0xd0018180 0x40>;
 			ngpios = <3>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupts-cells = <2>;
-			interrupts = <24>;
+			interrupts = <91>;
 		};
 
 		ethernet@d0034000 {

arch/arm/boot/dts/at91rm9200.dtsi

@@ -336,8 +336,8 @@
 
 	i2c@0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 0 /* sda */
-			 &pioA 24 0 /* scl */
+		gpios = <&pioA 25 0 /* sda */
+			 &pioA 26 0 /* scl */
 			>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -143,6 +143,11 @@
 						atmel,pins =
 							<0 3 0x1 0x0>;	/* PA3 periph A */
 					};
+
+					pinctrl_usart0_sck: usart0_sck-0 {
+						atmel,pins =
+							<0 4 0x1 0x0>;	/* PA4 periph A */
+					};
 				};
 
 				usart1 {
@@ -154,12 +159,17 @@
 
 					pinctrl_usart1_rts: usart1_rts-0 {
 						atmel,pins =
-							<3 27 0x3 0x0>;	/* PC27 periph C */
+							<2 27 0x3 0x0>;	/* PC27 periph C */
 					};
 
 					pinctrl_usart1_cts: usart1_cts-0 {
 						atmel,pins =
-							<3 28 0x3 0x0>;	/* PC28 periph C */
+							<2 28 0x3 0x0>;	/* PC28 periph C */
+					};
+
+					pinctrl_usart1_sck: usart1_sck-0 {
+						atmel,pins =
+							<2 28 0x3 0x0>;	/* PC29 periph C */
 					};
 				};
 
@@ -172,46 +182,56 @@
 
 					pinctrl_uart2_rts: uart2_rts-0 {
 						atmel,pins =
-							<0 0 0x2 0x0>;	/* PB0 periph B */
+							<1 0 0x2 0x0>;	/* PB0 periph B */
 					};
 
 					pinctrl_uart2_cts: uart2_cts-0 {
 						atmel,pins =
-							<0 1 0x2 0x0>;	/* PB1 periph B */
+							<1 1 0x2 0x0>;	/* PB1 periph B */
+					};
+
+					pinctrl_usart2_sck: usart2_sck-0 {
+						atmel,pins =
+							<1 2 0x2 0x0>;	/* PB2 periph B */
 					};
 				};
 
 				usart3 {
 					pinctrl_uart3: usart3-0 {
 						atmel,pins =
-							<3 23 0x2 0x1	/* PC22 periph B with pullup */
-							 3 23 0x2 0x0>;	/* PC23 periph B */
+							<2 23 0x2 0x1	/* PC22 periph B with pullup */
+							 2 23 0x2 0x0>;	/* PC23 periph B */
 					};
 
 					pinctrl_usart3_rts: usart3_rts-0 {
 						atmel,pins =
-							<3 24 0x2 0x0>;	/* PC24 periph B */
+							<2 24 0x2 0x0>;	/* PC24 periph B */
 					};
 
 					pinctrl_usart3_cts: usart3_cts-0 {
 						atmel,pins =
-							<3 25 0x2 0x0>;	/* PC25 periph B */
+							<2 25 0x2 0x0>;	/* PC25 periph B */
+					};
+
+					pinctrl_usart3_sck: usart3_sck-0 {
+						atmel,pins =
+							<2 26 0x2 0x0>;	/* PC26 periph B */
 					};
 				};
 
 				uart0 {
 					pinctrl_uart0: uart0-0 {
 						atmel,pins =
-							<3 8 0x3 0x0	/* PC8 periph C */
-							 3 9 0x3 0x1>;	/* PC9 periph C with pullup */
+							<2 8 0x3 0x0	/* PC8 periph C */
+							 2 9 0x3 0x1>;	/* PC9 periph C with pullup */
 					};
 				};
 
 				uart1 {
 					pinctrl_uart1: uart1-0 {
 						atmel,pins =
-							<3 16 0x3 0x0	/* PC16 periph C */
-							 3 17 0x3 0x1>;	/* PC17 periph C with pullup */
+							<2 16 0x3 0x0	/* PC16 periph C */
+							 2 17 0x3 0x1>;	/* PC17 periph C with pullup */
 					};
 				};
 
@@ -240,14 +260,14 @@
 
 					pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 {
 						atmel,pins =
-							<1 8 0x1 0x0	/* PA8 periph A */
-							 1 11 0x1 0x0	/* PA11 periph A */
-							 1 12 0x1 0x0	/* PA12 periph A */
-							 1 13 0x1 0x0	/* PA13 periph A */
-							 1 14 0x1 0x0	/* PA14 periph A */
-							 1 15 0x1 0x0	/* PA15 periph A */
-							 1 16 0x1 0x0	/* PA16 periph A */
-							 1 17 0x1 0x0>;	/* PA17 periph A */
+							<1 8 0x1 0x0	/* PB8 periph A */
+							 1 11 0x1 0x0	/* PB11 periph A */
+							 1 12 0x1 0x0	/* PB12 periph A */
+							 1 13 0x1 0x0	/* PB13 periph A */
+							 1 14 0x1 0x0	/* PB14 periph A */
+							 1 15 0x1 0x0	/* PB15 periph A */
+							 1 16 0x1 0x0	/* PB16 periph A */
+							 1 17 0x1 0x0>;	/* PB17 periph A */
 					};
 				};
 

arch/arm/boot/dts/cros5250-common.dtsi

@@ -96,8 +96,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -120,8 +120,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -141,8 +141,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;

arch/arm/boot/dts/dove-cubox.dts

@@ -26,10 +26,15 @@
 };
 
 &uart0 { status = "okay"; };
-&sdio0 { status = "okay"; };
 &sata0 { status = "okay"; };
 &i2c0 { status = "okay"; };
 
+&sdio0 {
+	status = "okay";
+	/* sdio0 card detect is connected to wrong pin on CuBox */
+	cd-gpios = <&gpio0 12 1>;
+};
+
 &spi0 {
 	status = "okay";
 
@@ -42,9 +47,14 @@
 };
 
 &pinctrl {
-	pinctrl-0 = <&pmx_gpio_18>;
+	pinctrl-0 = <&pmx_gpio_12 &pmx_gpio_18>;
 	pinctrl-names = "default";
 
+	pmx_gpio_12: pmx-gpio-12 {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+
 	pmx_gpio_18: pmx-gpio-18 {
 		marvell,pins = "mpp18";
 		marvell,function = "gpio";

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -115,8 +115,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;
@@ -139,8 +139,8 @@
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
-		samsung,dw-mshc-sdr-timing = <2 3 3>;
-		samsung,dw-mshc-ddr-timing = <1 2 3>;
+		samsung,dw-mshc-sdr-timing = <2 3>;
+		samsung,dw-mshc-ddr-timing = <1 2>;
 
 		slot@0 {
 			reg = <0>;

arch/arm/boot/dts/kirkwood-ns2-common.dtsi

@@ -1,4 +1,5 @@
 /include/ "kirkwood.dtsi"
+/include/ "kirkwood-6281.dtsi"
 
 / {
 	chosen {
@@ -6,6 +7,21 @@
 	};
 
 	ocp@f1000000 {
+		pinctrl: pinctrl@10000 {
+			pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0
+					&pmx_ns2_sata0 &pmx_ns2_sata1>;
+			pinctrl-names = "default";
+
+			pmx_ns2_sata0: pmx-ns2-sata0 {
+				marvell,pins = "mpp21";
+				marvell,function = "sata0";
+			};
+			pmx_ns2_sata1: pmx-ns2-sata1 {
+				marvell,pins = "mpp20";
+				marvell,function = "sata1";
+			};
+		};
+
 		serial@12000 {
 			clock-frequency = <166666667>;
 			status = "okay";

arch/arm/boot/dts/kirkwood.dtsi

@@ -36,6 +36,7 @@
 			reg = <0x10100 0x40>;
 			ngpios = <32>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <35>, <36>, <37>, <38>;
 		};
 
@@ -46,6 +47,7 @@
 			reg = <0x10140 0x40>;
 			ngpios = <18>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <39>, <40>, <41>;
 		};
 

arch/arm/boot/dts/kizbox.dts

@@ -48,6 +48,8 @@
 
 			macb0: ethernet@fffc4000 {
 				phy-mode = "mii";
+				pinctrl-0 = <&pinctrl_macb_rmii
+				             &pinctrl_macb_rmii_mii_alt>;
 				status = "okay";
 			};
 

arch/arm/boot/dts/sunxi.dtsi

@@ -60,19 +60,21 @@
 		};
 
 		uart0: uart@01c28000 {
-			compatible = "ns8250";
+			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
 			interrupts = <1>;
 			reg-shift = <2>;
+			reg-io-width = <4>;
 			clock-frequency = <24000000>;
 			status = "disabled";
 		};
 
 		uart1: uart@01c28400 {
-			compatible = "ns8250";
+			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
 			interrupts = <2>;
 			reg-shift = <2>;
+			reg-io-width = <4>;
 			clock-frequency = <24000000>;
 			status = "disabled";
 		};

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

@@ -45,7 +45,6 @@
 			reg = <1>;
 		};
 
-/* A7s disabled till big.LITTLE patches are available...
 		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
@@ -63,7 +62,6 @@
 			compatible = "arm,cortex-a7";
 			reg = <0x102>;
 		};
-*/
 	};
 
 	memory@80000000 {

arch/arm/common/gic.c

@@ -351,6 +351,25 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
 	irq_set_chained_handler(irq, gic_handle_cascade_irq);
 }
 
+static u8 gic_get_cpumask(struct gic_chip_data *gic)
+{
+	void __iomem *base = gic_data_dist_base(gic);
+	u32 mask, i;
+
+	for (i = mask = 0; i < 32; i += 4) {
+		mask = readl_relaxed(base + GIC_DIST_TARGET + i);
+		mask |= mask >> 16;
+		mask |= mask >> 8;
+		if (mask)
+			break;
+	}
+
+	if (!mask)
+		pr_crit("GIC CPU mask not found - kernel will fail to boot.\n");
+
+	return mask;
+}
+
 static void __init gic_dist_init(struct gic_chip_data *gic)
 {
 	unsigned int i;
@@ -369,7 +388,9 @@ static void __init gic_dist_init(struct gic_chip_data *gic)
 	/*
 	 * Set all global interrupts to this CPU only.
 	 */
-	cpumask = readl_relaxed(base + GIC_DIST_TARGET + 0);
+	cpumask = gic_get_cpumask(gic);
+	cpumask |= cpumask << 8;
+	cpumask |= cpumask << 16;
 	for (i = 32; i < gic_irqs; i += 4)
 		writel_relaxed(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
 
@@ -400,7 +421,7 @@ static void __cpuinit gic_cpu_init(struct gic_chip_data *gic)
 	 * Get what the GIC says our CPU mask is.
 	 */
 	BUG_ON(cpu >= NR_GIC_CPU_IF);
-	cpu_mask = readl_relaxed(dist_base + GIC_DIST_TARGET + 0);
+	cpu_mask = gic_get_cpumask(gic);
 	gic_cpu_map[cpu] = cpu_mask;
 
 	/*

arch/arm/configs/at91_dt_defconfig

@@ -19,6 +19,7 @@ CONFIG_SOC_AT91SAM9260=y
 CONFIG_SOC_AT91SAM9263=y
 CONFIG_SOC_AT91SAM9G45=y
 CONFIG_SOC_AT91SAM9X5=y
+CONFIG_SOC_AT91SAM9N12=y
 CONFIG_MACH_AT91SAM_DT=y
 CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
 CONFIG_AT91_TIMER_HZ=128
@@ -31,7 +32,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
-CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
 CONFIG_KEXEC=y
 CONFIG_AUTO_ZRELADDR=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set

arch/arm/include/asm/memory.h

@@ -37,7 +37,7 @@
  */
 #define PAGE_OFFSET		UL(CONFIG_PAGE_OFFSET)
 #define TASK_SIZE		(UL(CONFIG_PAGE_OFFSET) - UL(0x01000000))
-#define TASK_UNMAPPED_BASE	(UL(CONFIG_PAGE_OFFSET) / 3)
+#define TASK_UNMAPPED_BASE	ALIGN(TASK_SIZE / 3, SZ_16M)
 
 /*
  * The maximum size of a 26-bit user space task.

arch/arm/kernel/debug.S

@@ -100,12 +100,14 @@ ENTRY(printch)
 		b	1b
 ENDPROC(printch)
 
+#ifdef CONFIG_MMU
 ENTRY(debug_ll_addr)
 		addruart r2, r3, ip
 		str	r2, [r0]
 		str	r3, [r1]
 		mov	pc, lr
 ENDPROC(debug_ll_addr)
+#endif
 
 #else
 

arch/arm/kernel/head.S

@@ -246,6 +246,7 @@ __create_page_tables:
 
 	/*
 	 * Then map boot params address in r2 if specified.
+	 * We map 2 sections in case the ATAGs/DTB crosses a section boundary.
 	 */
 	mov	r0, r2, lsr #SECTION_SHIFT
 	movs	r0, r0, lsl #SECTION_SHIFT
@@ -253,6 +254,8 @@ __create_page_tables:
 	addne	r3, r3, #PAGE_OFFSET
 	addne	r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER)
 	orrne	r6, r7, r0
+	strne	r6, [r3], #1 << PMD_ORDER
+	addne	r6, r6, #1 << SECTION_SHIFT
 	strne	r6, [r3]
 
 #ifdef CONFIG_DEBUG_LL
@@ -331,7 +334,7 @@ ENTRY(secondary_startup)
 	 * as it has already been validated by the primary processor.
 	 */
 #ifdef CONFIG_ARM_VIRT_EXT
-	bl	__hyp_stub_install
+	bl	__hyp_stub_install_secondary
 #endif
 	safe_svcmode_maskall r9
 

arch/arm/kernel/hyp-stub.S

@@ -99,7 +99,7 @@ ENTRY(__hyp_stub_install_secondary)
 	 * immediately.
 	 */
 	compare_cpu_mode_with_primary	r4, r5, r6, r7
-	bxne	lr
+	movne	pc, lr
 
 	/*
 	 * Once we have given up on one CPU, we do not try to install the
@@ -111,7 +111,7 @@ ENTRY(__hyp_stub_install_secondary)
 	 */
 
 	cmp	r4, #HYP_MODE
-	bxne	lr			@ give up if the CPU is not in HYP mode
+	movne	pc, lr			@ give up if the CPU is not in HYP mode
 
 /*
  * Configure HSCTLR to set correct exception endianness/instruction set
@@ -120,7 +120,8 @@ ENTRY(__hyp_stub_install_secondary)
  * Eventually, CPU-specific code might be needed -- assume not for now
  *
  * This code relies on the "eret" instruction to synchronize the
- * various coprocessor accesses.
+ * various coprocessor accesses. This is done when we switch to SVC
+ * (see safe_svcmode_maskall).
  */
 	@ Now install the hypervisor stub:
 	adr	r7, __hyp_stub_vectors
@@ -155,14 +156,7 @@ THUMB(	orr	r7, #(1 << 30)	)	@ HSCTLR.TE
 1:
 #endif
 
-	bic	r7, r4, #MODE_MASK
-	orr	r7, r7, #SVC_MODE
-THUMB(	orr	r7, r7, #PSR_T_BIT	)
-	msr	spsr_cxsf, r7		@ This is SPSR_hyp.
-
-	__MSR_ELR_HYP(14)		@ msr elr_hyp, lr
-	__ERET				@ return, switching to SVC mode
-					@ The boot CPU mode is left in r4.
+	bx	lr			@ The boot CPU mode is left in r4.
 ENDPROC(__hyp_stub_install_secondary)
 
 __hyp_stub_do_trap:
@@ -200,7 +194,7 @@ ENDPROC(__hyp_get_vectors)
 	@ fall through
 ENTRY(__hyp_set_vectors)
 	__HVC(0)
-	bx	lr
+	mov	pc, lr
 ENDPROC(__hyp_set_vectors)
 
 #ifndef ZIMAGE

arch/arm/mach-at91/setup.c

@@ -105,6 +105,8 @@ static void __init soc_detect(u32 dbgu_base)
 	switch (socid) {
 	case ARCH_ID_AT91RM9200:
 		at91_soc_initdata.type = AT91_SOC_RM9200;
+		if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_NONE)
+			at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
 		at91_boot_soc = at91rm9200_soc;
 		break;
 

arch/arm/mach-exynos/Kconfig

@@ -414,7 +414,7 @@ config MACH_EXYNOS4_DT
 	select CPU_EXYNOS4210
 	select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
 	select PINCTRL
-	select PINCTRL_EXYNOS4
+	select PINCTRL_EXYNOS
 	select USE_OF
 	help
 	  Machine support for Samsung Exynos4 machine with device tree enabled.

arch/arm/mach-imx/Kconfig

@@ -851,6 +851,7 @@ config SOC_IMX6Q
 	select HAVE_CAN_FLEXCAN if CAN
 	select HAVE_IMX_GPC
 	select HAVE_IMX_MMDC
+	select HAVE_IMX_SRC
 	select HAVE_SMP
 	select MFD_SYSCON
 	select PINCTRL

arch/arm/mach-imx/clk-imx6q.c

@@ -436,6 +436,9 @@ int __init mx6q_clocks_init(void)
 	for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
 		clk_prepare_enable(clk[clks_init_on[i]]);
 
+	/* Set initial power mode */
+	imx6q_set_lpm(WAIT_CLOCKED);
+
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
 	base = of_iomap(np, 0);
 	WARN_ON(!base);

arch/arm/mach-imx/common.h

@@ -142,6 +142,7 @@ extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
 extern void imx6q_clock_map_io(void);
 
 extern void imx_cpu_die(unsigned int cpu);
+extern int imx_cpu_kill(unsigned int cpu);
 
 #ifdef CONFIG_PM
 extern void imx6q_pm_init(void);

arch/arm/mach-imx/devices/platform-imx-fb.c

@@ -54,7 +54,7 @@ struct platform_device *__init imx_add_imx_fb(
 			.flags = IORESOURCE_IRQ,
 		},
 	};
-	return imx_add_platform_device_dmamask("imx-fb", 0,
+	return imx_add_platform_device_dmamask(data->devid, 0,
 			res, ARRAY_SIZE(res),
 			pdata, sizeof(*pdata), DMA_BIT_MASK(32));
 }

arch/arm/mach-imx/hotplug.c

@@ -46,9 +46,11 @@ static inline void cpu_enter_lowpower(void)
 void imx_cpu_die(unsigned int cpu)
 {
 	cpu_enter_lowpower();
-	imx_enable_cpu(cpu, false);
+	cpu_do_idle();
+}
 
-	/* spin here until hardware takes it down */
-	while (1)
-		;
+int imx_cpu_kill(unsigned int cpu)
+{
+	imx_enable_cpu(cpu, false);
+	return 1;
 }

arch/arm/mach-imx/iram_alloc.c

@@ -22,8 +22,7 @@
 #include <linux/module.h>
 #include <linux/spinlock.h>
 #include <linux/genalloc.h>
-
-#include "iram.h"
+#include "linux/platform_data/imx-iram.h"
 
 static unsigned long iram_phys_base;
 static void __iomem *iram_virt_base;

arch/arm/mach-imx/platsmp.c

@@ -92,5 +92,6 @@ struct smp_operations  imx_smp_ops __initdata = {
 	.smp_boot_secondary	= imx_boot_secondary,
 #ifdef CONFIG_HOTPLUG_CPU
 	.cpu_die		= imx_cpu_die,
+	.cpu_kill		= imx_cpu_kill,
 #endif
 };

arch/arm/mach-imx/pm-imx6q.c

@@ -41,6 +41,7 @@ static int imx6q_pm_enter(suspend_state_t state)
 		cpu_suspend(0, imx6q_suspend_finish);
 		imx_smp_prepare();
 		imx_gpc_post_resume();
+		imx6q_set_lpm(WAIT_CLOCKED);
 		break;
 	default:
 		return -EINVAL;

arch/arm/mach-integrator/pci_v3.c

@@ -475,13 +475,12 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys)
 {
 	int ret = 0;
 
+	if (!ap_syscon_base)
+		return -EINVAL;
+
 	if (nr == 0) {
 		sys->mem_offset = PHYS_PCI_MEM_BASE;
 		ret = pci_v3_setup_resources(sys);
-		/* Remap the Integrator system controller */
-		ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
-		if (!ap_syscon_base)
-			return -EINVAL;
 	}
 
 	return ret;
@@ -497,6 +496,13 @@ void __init pci_v3_preinit(void)
 	unsigned int temp;
 	int ret;
 
+	/* Remap the Integrator system controller */
+	ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100);
+	if (!ap_syscon_base) {
+		pr_err("unable to remap the AP syscon for PCIv3\n");
+		return;
+	}
+
 	pcibios_min_mem = 0x00100000;
 
 	/*

arch/arm/mach-kirkwood/board-ns2.c

@@ -18,47 +18,11 @@
 #include <linux/gpio.h>
 #include <linux/of.h>
 #include "common.h"
-#include "mpp.h"
 
 static struct mv643xx_eth_platform_data ns2_ge00_data = {
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
 };
 
-static unsigned int ns2_mpp_config[] __initdata = {
-	MPP0_SPI_SCn,
-	MPP1_SPI_MOSI,
-	MPP2_SPI_SCK,
-	MPP3_SPI_MISO,
-	MPP4_NF_IO6,
-	MPP5_NF_IO7,
-	MPP6_SYSRST_OUTn,
-	MPP7_GPO,		/* Fan speed (bit 1) */
-	MPP8_TW0_SDA,
-	MPP9_TW0_SCK,
-	MPP10_UART0_TXD,
-	MPP11_UART0_RXD,
-	MPP12_GPO,		/* Red led */
-	MPP14_GPIO,		/* USB fuse */
-	MPP16_GPIO,		/* SATA 0 power */
-	MPP17_GPIO,		/* SATA 1 power */
-	MPP18_NF_IO0,
-	MPP19_NF_IO1,
-	MPP20_SATA1_ACTn,
-	MPP21_SATA0_ACTn,
-	MPP22_GPIO,		/* Fan speed (bit 0) */
-	MPP23_GPIO,		/* Fan power */
-	MPP24_GPIO,		/* USB mode select */
-	MPP25_GPIO,		/* Fan rotation fail */
-	MPP26_GPIO,		/* USB device vbus */
-	MPP28_GPIO,		/* USB enable host vbus */
-	MPP29_GPIO,		/* Blue led (slow register) */
-	MPP30_GPIO,		/* Blue led (command register) */
-	MPP31_GPIO,		/* Board power off */
-	MPP32_GPIO,		/* Power button (0 = Released, 1 = Pushed) */
-	MPP33_GPO,		/* Fan speed (bit 2) */
-	0
-};
-
 #define NS2_GPIO_POWER_OFF	31
 
 static void ns2_power_off(void)
@@ -71,8 +35,6 @@ void __init ns2_init(void)
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
-	kirkwood_mpp_conf(ns2_mpp_config);
-
 	if (of_machine_is_compatible("lacie,netspace_lite_v2") ||
 	    of_machine_is_compatible("lacie,netspace_mini_v2"))
 		ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0);

arch/arm/mach-mvebu/Makefile

@@ -1,6 +1,8 @@
 ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
 	-I$(srctree)/arch/arm/plat-orion/include
 
+AFLAGS_coherency_ll.o		:= -Wa,-march=armv7-a
+
 obj-y += system-controller.o
 obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o irq-armada-370-xp.o addr-map.o coherency.o coherency_ll.o pmsu.o
 obj-$(CONFIG_SMP)                += platsmp.o headsmp.o

arch/arm/mach-omap2/board-omap4panda.c

@@ -397,6 +397,12 @@ static struct omap_board_mux board_mux[] __initdata = {
 		  OMAP_PULL_ENA),
 	OMAP4_MUX(ABE_MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
 
+	/* UART2 - BT/FM/GPS shared transport */
+	OMAP4_MUX(UART2_CTS,	OMAP_PIN_INPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_RTS,	OMAP_PIN_OUTPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_RX,	OMAP_PIN_INPUT	| OMAP_MUX_MODE0),
+	OMAP4_MUX(UART2_TX,	OMAP_PIN_OUTPUT	| OMAP_MUX_MODE0),
+
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 

arch/arm/mach-omap2/cclock2420_data.c

@@ -1935,6 +1935,8 @@ int __init omap2420_clk_init(void)
 			omap2_init_clk_hw_omap_clocks(c->lk.clk);
 	}
 
+	omap2xxx_clkt_vps_late_init();
+
 	omap2_clk_disable_autoidle_all();
 
 	omap2_clk_enable_init_clocks(enable_init_clks,

arch/arm/mach-omap2/cclock2430_data.c

@@ -2050,6 +2050,8 @@ int __init omap2430_clk_init(void)
 			omap2_init_clk_hw_omap_clocks(c->lk.clk);
 	}
 
+	omap2xxx_clkt_vps_late_init();
+
 	omap2_clk_disable_autoidle_all();
 
 	omap2_clk_enable_init_clocks(enable_init_clks,

arch/arm/mach-omap2/cclock44xx_data.c

@@ -2026,14 +2026,13 @@ int __init omap4xxx_clk_init(void)
 	 * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power
 	 * state when turning the ABE clock domain. Workaround this by
 	 * locking the ABE DPLL on boot.
+	 * Lock the ABE DPLL in any case to avoid issues with audio.
 	 */
-	if (cpu_is_omap446x()) {
-		rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
-		if (!rc)
-			rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
-		if (rc)
-			pr_err("%s: failed to configure ABE DPLL!\n", __func__);
-	}
+	rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck);
+	if (!rc)
+		rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ);
+	if (rc)
+		pr_err("%s: failed to configure ABE DPLL!\n", __func__);
 
 	return 0;
 }

arch/arm/mach-omap2/devices.c

@@ -639,7 +639,7 @@ static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev)
 	return cnt;
 }
 
-static void omap_init_ocp2scp(void)
+static void __init omap_init_ocp2scp(void)
 {
 	struct omap_hwmod	*oh;
 	struct platform_device	*pdev;

arch/arm/mach-omap2/drm.c

@@ -25,6 +25,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/platform_data/omap_drm.h>
 
+#include "soc.h"
 #include "omap_device.h"
 #include "omap_hwmod.h"
 
@@ -56,7 +57,7 @@ static int __init omap_init_drm(void)
 			oh->name);
 	}
 
-	platform_data.omaprev = GET_OMAP_REVISION();
+	platform_data.omaprev = GET_OMAP_TYPE;
 
 	return platform_device_register(&omap_drm_device);
 

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -2132,8 +2132,12 @@ static struct omap_hwmod omap44xx_mcpdm_hwmod = {
 	 * currently reset very early during boot, before I2C is
 	 * available, so it doesn't seem that we have any choice in
 	 * the kernel other than to avoid resetting it.
+	 *
+	 * Also, McPDM needs to be configured to NO_IDLE mode when it
+	 * is in used otherwise vital clocks will be gated which
+	 * results 'slow motion' audio playback.
 	 */
-	.flags		= HWMOD_EXT_OPT_MAIN_CLK,
+	.flags		= HWMOD_EXT_OPT_MAIN_CLK | HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_mcpdm_irqs,
 	.sdma_reqs	= omap44xx_mcpdm_sdma_reqs,
 	.main_clk	= "mcpdm_fck",

arch/arm/mach-omap2/timer.c

@@ -165,15 +165,11 @@ static struct device_node * __init omap_get_timer_dt(struct of_device_id *match,
 	struct device_node *np;
 
 	for_each_matching_node(np, match) {
-		if (!of_device_is_available(np)) {
-			of_node_put(np);
+		if (!of_device_is_available(np))
 			continue;
-		}
 
-		if (property && !of_get_property(np, property, NULL)) {
-			of_node_put(np);
+		if (property && !of_get_property(np, property, NULL))
 			continue;
-		}
 
 		of_add_property(np, &device_disabled);
 		return np;

arch/arm/mach-realview/include/mach/irqs-eb.h

@@ -115,7 +115,7 @@
 /*
  * Only define NR_IRQS if less than NR_IRQS_EB
  */
-#define NR_IRQS_EB		(IRQ_EB_GIC_START + 96)
+#define NR_IRQS_EB		(IRQ_EB_GIC_START + 128)
 
 #if defined(CONFIG_MACH_REALVIEW_EB) \
 	&& (!defined(NR_IRQS) || (NR_IRQS < NR_IRQS_EB))

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -47,7 +47,7 @@ static struct spi_board_info wm1253_devs[] = {
 		.bus_num	= 0,
 		.chip_select	= 0,
 		.mode		= SPI_MODE_0,
-		.irq		= S3C_EINT(5),
+		.irq		= S3C_EINT(4),
 		.controller_data = &wm0010_spi_csinfo,
 		.platform_data = &wm0010_pdata,
 	},

arch/arm/mach-s3c64xx/pm.c

@@ -338,8 +338,10 @@ int __init s3c64xx_pm_init(void)
 	for (i = 0; i < ARRAY_SIZE(s3c64xx_pm_domains); i++)
 		pm_genpd_init(&s3c64xx_pm_domains[i]->pd, NULL, false);
 
+#ifdef CONFIG_S3C_DEV_FB
 	if (dev_get_platdata(&s3c_device_fb.dev))
 		pm_genpd_add_device(&s3c64xx_pm_f.pd, &s3c_device_fb.dev);
+#endif
 
 	return 0;
 }

arch/arm/mm/dma-mapping.c

@@ -640,7 +640,7 @@ static void *__dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
 
 	if (is_coherent || nommu())
 		addr = __alloc_simple_buffer(dev, size, gfp, &page);
-	else if (gfp & GFP_ATOMIC)
+	else if (!(gfp & __GFP_WAIT))
 		addr = __alloc_from_pool(size, &page);
 	else if (!IS_ENABLED(CONFIG_CMA))
 		addr = __alloc_remap_buffer(dev, size, gfp, prot, &page, caller);
@@ -774,25 +774,27 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
 	size_t size, enum dma_data_direction dir,
 	void (*op)(const void *, size_t, int))
 {
+	unsigned long pfn;
+	size_t left = size;
+
+	pfn = page_to_pfn(page) + offset / PAGE_SIZE;
+	offset %= PAGE_SIZE;
+
 	/*
 	 * A single sg entry may refer to multiple physically contiguous
 	 * pages.  But we still need to process highmem pages individually.
 	 * If highmem is not configured then the bulk of this loop gets
 	 * optimized out.
 	 */
-	size_t left = size;
 	do {
 		size_t len = left;
 		void *vaddr;
 
+		page = pfn_to_page(pfn);
+
 		if (PageHighMem(page)) {
-			if (len + offset > PAGE_SIZE) {
-				if (offset >= PAGE_SIZE) {
-					page += offset / PAGE_SIZE;
-					offset %= PAGE_SIZE;
-				}
+			if (len + offset > PAGE_SIZE)
 				len = PAGE_SIZE - offset;
-			}
 			vaddr = kmap_high_get(page);
 			if (vaddr) {
 				vaddr += offset;
@@ -809,7 +811,7 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
 			op(vaddr, len, dir);
 		}
 		offset = 0;
-		page++;
+		pfn++;
 		left -= len;
 	} while (left);
 }

arch/arm/mm/mmu.c

@@ -283,7 +283,7 @@ static struct mem_type mem_types[] = {
 	},
 	[MT_MEMORY_SO] = {
 		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
-				L_PTE_MT_UNCACHED,
+				L_PTE_MT_UNCACHED | L_PTE_XN,
 		.prot_l1   = PMD_TYPE_TABLE,
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_S |
 				PMD_SECT_UNCACHED | PMD_SECT_XN,

arch/arm/plat-versatile/headsmp.S

@@ -20,7 +20,7 @@
  */
 ENTRY(versatile_secondary_startup)
 	mrc	p15, 0, r0, c0, c0, 5
-	and	r0, r0, #15
+	bic	r0, #0xff000000
 	adr	r4, 1f
 	ldmia	r4, {r5, r6}
 	sub	r4, r4, r5

arch/arm/vfp/entry.S

@@ -22,7 +22,7 @@
 @  IRQs disabled.
 @
 ENTRY(do_vfp)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	add	r11, r4, #1		@ increment it
 	str	r11, [r10, #TI_PREEMPT]
@@ -35,7 +35,7 @@ ENTRY(do_vfp)
 ENDPROC(do_vfp)
 
 ENTRY(vfp_null_entry)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it
@@ -53,7 +53,7 @@ ENDPROC(vfp_null_entry)
 
 	__INIT
 ENTRY(vfp_testing_entry)
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it

arch/arm/vfp/vfphw.S

@@ -168,7 +168,7 @@ vfp_hw_state_valid:
 					@ else it's one 32-bit instruction, so
 					@ always subtract 4 from the following
 					@ instruction address.
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it
@@ -192,7 +192,7 @@ look_for_VFP_exceptions:
 	@ not recognised by VFP
 
 	DBGSTR	"not VFP"
-#ifdef CONFIG_PREEMPT
+#ifdef CONFIG_PREEMPT_COUNT
 	get_thread_info	r10
 	ldr	r4, [r10, #TI_PREEMPT]	@ get preempt count
 	sub	r11, r4, #1		@ decrement it

arch/avr32/include/asm/dma-mapping.h

@@ -336,4 +336,14 @@ dma_sync_sg_for_device(struct device *dev, struct scatterlist *sg,
 #define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent(d, s, h, f)
 #define dma_free_noncoherent(d, s, v, h) dma_free_coherent(d, s, v, h)
 
+/* drivers/base/dma-mapping.c */
+extern int dma_common_mmap(struct device *dev, struct vm_area_struct *vma,
+			   void *cpu_addr, dma_addr_t dma_addr, size_t size);
+extern int dma_common_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size);
+
+#define dma_mmap_coherent(d, v, c, h, s) dma_common_mmap(d, v, c, h, s)
+#define dma_get_sgtable(d, t, v, h, s) dma_common_get_sgtable(d, t, v, h, s)
+
 #endif /* __ASM_AVR32_DMA_MAPPING_H */

arch/blackfin/include/asm/dma-mapping.h

@@ -154,4 +154,14 @@ dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 	_dma_sync((dma_addr_t)vaddr, size, dir);
 }
 
+/* drivers/base/dma-mapping.c */
+extern int dma_common_mmap(struct device *dev, struct vm_area_struct *vma,
+			   void *cpu_addr, dma_addr_t dma_addr, size_t size);
+extern int dma_common_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size);
+
+#define dma_mmap_coherent(d, v, c, h, s) dma_common_mmap(d, v, c, h, s)
+#define dma_get_sgtable(d, t, v, h, s) dma_common_get_sgtable(d, t, v, h, s)
+
 #endif				/* _BLACKFIN_DMA_MAPPING_H */

arch/c6x/include/asm/dma-mapping.h

@@ -89,4 +89,19 @@ extern void dma_free_coherent(struct device *, size_t, void *, dma_addr_t);
 #define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent((d), (s), (h), (f))
 #define dma_free_noncoherent(d, s, v, h)  dma_free_coherent((d), (s), (v), (h))
 
+/* Not supported for now */
+static inline int dma_mmap_coherent(struct device *dev,
+				    struct vm_area_struct *vma, void *cpu_addr,
+				    dma_addr_t dma_addr, size_t size)
+{
+	return -EINVAL;
+}
+
+static inline int dma_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size)
+{
+	return -EINVAL;
+}
+
 #endif	/* _ASM_C6X_DMA_MAPPING_H */

arch/cris/include/asm/dma-mapping.h

@@ -158,5 +158,15 @@ dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 {
 }
 
+/* drivers/base/dma-mapping.c */
+extern int dma_common_mmap(struct device *dev, struct vm_area_struct *vma,
+			   void *cpu_addr, dma_addr_t dma_addr, size_t size);
+extern int dma_common_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size);
+
+#define dma_mmap_coherent(d, v, c, h, s) dma_common_mmap(d, v, c, h, s)
+#define dma_get_sgtable(d, t, v, h, s) dma_common_get_sgtable(d, t, v, h, s)
+
 
 #endif

arch/frv/include/asm/dma-mapping.h

@@ -132,4 +132,19 @@ void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 	flush_write_buffers();
 }
 
+/* Not supported for now */
+static inline int dma_mmap_coherent(struct device *dev,
+				    struct vm_area_struct *vma, void *cpu_addr,
+				    dma_addr_t dma_addr, size_t size)
+{
+	return -EINVAL;
+}
+
+static inline int dma_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size)
+{
+	return -EINVAL;
+}
+
 #endif  /* _ASM_DMA_MAPPING_H */

arch/m68k/include/asm/dma-mapping.h

@@ -115,4 +115,14 @@ static inline int dma_mapping_error(struct device *dev, dma_addr_t handle)
 #include <asm-generic/dma-mapping-broken.h>
 #endif
 
+/* drivers/base/dma-mapping.c */
+extern int dma_common_mmap(struct device *dev, struct vm_area_struct *vma,
+			   void *cpu_addr, dma_addr_t dma_addr, size_t size);
+extern int dma_common_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size);
+
+#define dma_mmap_coherent(d, v, c, h, s) dma_common_mmap(d, v, c, h, s)
+#define dma_get_sgtable(d, t, v, h, s) dma_common_get_sgtable(d, t, v, h, s)
+
 #endif  /* _M68K_DMA_MAPPING_H */

arch/mips/bcm47xx/Kconfig

@@ -8,8 +8,10 @@ config BCM47XX_SSB
 	select SSB_DRIVER_EXTIF
 	select SSB_EMBEDDED
 	select SSB_B43_PCI_BRIDGE if PCI
+	select SSB_DRIVER_PCICORE if PCI
 	select SSB_PCICORE_HOSTMODE if PCI
 	select SSB_DRIVER_GPIO
+	select GPIOLIB
 	default y
 	help
 	 Add support for old Broadcom BCM47xx boards with Sonics Silicon Backplane support.
@@ -25,6 +27,7 @@ config BCM47XX_BCMA
 	select BCMA_HOST_PCI if PCI
 	select BCMA_DRIVER_PCI_HOSTMODE if PCI
 	select BCMA_DRIVER_GPIO
+	select GPIOLIB
 	default y
 	help
 	 Add support for new Broadcom BCM47xx boards with Broadcom specific Advanced Microcontroller Bus.

arch/mips/cavium-octeon/executive/cvmx-l2c.c

@@ -30,6 +30,7 @@
  * measurement, and debugging facilities.
  */
 
+#include <linux/compiler.h>
 #include <linux/irqflags.h>
 #include <asm/octeon/cvmx.h>
 #include <asm/octeon/cvmx-l2c.h>
@@ -285,22 +286,22 @@ uint64_t cvmx_l2c_read_perf(uint32_t counter)
  */
 static void fault_in(uint64_t addr, int len)
 {
-	volatile char *ptr;
-	volatile char dummy;
+	char *ptr;
+
 	/*
 	 * Adjust addr and length so we get all cache lines even for
 	 * small ranges spanning two cache lines.
 	 */
 	len += addr & CVMX_CACHE_LINE_MASK;
 	addr &= ~CVMX_CACHE_LINE_MASK;
-	ptr = (volatile char *)cvmx_phys_to_ptr(addr);
+	ptr = cvmx_phys_to_ptr(addr);
 	/*
 	 * Invalidate L1 cache to make sure all loads result in data
 	 * being in L2.
 	 */
 	CVMX_DCACHE_INVALIDATE;
 	while (len > 0) {
-		dummy += *ptr;
+		ACCESS_ONCE(*ptr);
 		len -= CVMX_CACHE_LINE_SIZE;
 		ptr += CVMX_CACHE_LINE_SIZE;
 	}

arch/mips/include/asm/dsp.h

@@ -16,7 +16,7 @@
 #include <asm/mipsregs.h>
 
 #define DSP_DEFAULT	0x00000000
-#define DSP_MASK	0x3ff
+#define DSP_MASK	0x3f
 
 #define __enable_dsp_hazard()						\
 do {									\

arch/mips/include/asm/inst.h

@@ -353,6 +353,7 @@ union mips_instruction {
 	struct u_format u_format;
 	struct c_format c_format;
 	struct r_format r_format;
+	struct p_format p_format;
 	struct f_format f_format;
 	struct ma_format ma_format;
 	struct b_format b_format;

arch/mips/include/asm/mach-pnx833x/war.h

@@ -21,4 +21,4 @@
 #define R10000_LLSC_WAR			0
 #define MIPS34K_MISSED_ITLB_WAR		0
 
-#endif /* __ASM_MIPS_MACH_PNX8550_WAR_H */
+#endif /* __ASM_MIPS_MACH_PNX833X_WAR_H */

arch/mips/include/asm/pgtable-64.h

@@ -230,6 +230,7 @@ static inline void pud_clear(pud_t *pudp)
 #else
 #define pte_pfn(x)		((unsigned long)((x).pte >> _PFN_SHIFT))
 #define pfn_pte(pfn, prot)	__pte(((pfn) << _PFN_SHIFT) | pgprot_val(prot))
+#define pfn_pmd(pfn, prot)	__pmd(((pfn) << _PFN_SHIFT) | pgprot_val(prot))
 #endif
 
 #define __pgd_offset(address)	pgd_index(address)

arch/mips/include/uapi/asm/Kbuild

@@ -3,6 +3,7 @@ include include/uapi/asm-generic/Kbuild.asm
 
 header-y += auxvec.h
 header-y += bitsperlong.h
+header-y += break.h
 header-y += byteorder.h
 header-y += cachectl.h
 header-y += errno.h

arch/mips/kernel/ftrace.c

@@ -25,6 +25,12 @@
 #define MCOUNT_OFFSET_INSNS 4
 #endif
 
+/* Arch override because MIPS doesn't need to run this from stop_machine() */
+void arch_ftrace_update_code(int command)
+{
+	ftrace_modify_all_code(command);
+}
+
 /*
  * Check if the address is in kernel space
  *
@@ -89,6 +95,24 @@ static int ftrace_modify_code(unsigned long ip, unsigned int new_code)
 	return 0;
 }
 
+#ifndef CONFIG_64BIT
+static int ftrace_modify_code_2(unsigned long ip, unsigned int new_code1,
+				unsigned int new_code2)
+{
+	int faulted;
+
+	safe_store_code(new_code1, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+	ip += 4;
+	safe_store_code(new_code2, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+	flush_icache_range(ip, ip + 8); /* original ip + 12 */
+	return 0;
+}
+#endif
+
 /*
  * The details about the calling site of mcount on MIPS
  *
@@ -131,8 +155,18 @@ int ftrace_make_nop(struct module *mod,
 	 * needed.
 	 */
 	new = in_kernel_space(ip) ? INSN_NOP : INSN_B_1F;
-
+#ifdef CONFIG_64BIT
 	return ftrace_modify_code(ip, new);
+#else
+	/*
+	 * On 32 bit MIPS platforms, gcc adds a stack adjust
+	 * instruction in the delay slot after the branch to
+	 * mcount and expects mcount to restore the sp on return.
+	 * This is based on a legacy API and does nothing but
+	 * waste instructions so it's being removed at runtime.
+	 */
+	return ftrace_modify_code_2(ip, new, INSN_NOP);
+#endif
 }
 
 int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)

arch/mips/kernel/mcount.S

@@ -46,9 +46,8 @@
 	PTR_L	a5, PT_R9(sp)
 	PTR_L	a6, PT_R10(sp)
 	PTR_L	a7, PT_R11(sp)
-	PTR_ADDIU	sp, PT_SIZE
 #else
-	PTR_ADDIU	sp, (PT_SIZE + 8)
+	PTR_ADDIU	sp, PT_SIZE
 #endif
 .endm
 
@@ -69,7 +68,9 @@ NESTED(ftrace_caller, PT_SIZE, ra)
 	.globl _mcount
 _mcount:
 	b	ftrace_stub
-	 nop
+	addiu sp,sp,8
+
+	/* When tracing is activated, it calls ftrace_caller+8 (aka here) */
 	lw	t1, function_trace_stop
 	bnez	t1, ftrace_stub
 	 nop

arch/mips/kernel/vpe.c

@@ -705,7 +705,7 @@ static int vpe_run(struct vpe * v)
 
 			printk(KERN_WARNING
 			       "VPE loader: TC %d is already in use.\n",
-                               t->index);
+			       v->tc->index);
 			return -ENOEXEC;
 		}
 	} else {

arch/mips/lantiq/irq.c

@@ -408,7 +408,7 @@ int __init icu_of_init(struct device_node *node, struct device_node *parent)
 #endif
 
 	/* tell oprofile which irq to use */
-	cp0_perfcount_irq = LTQ_PERF_IRQ;
+	cp0_perfcount_irq = irq_create_mapping(ltq_domain, LTQ_PERF_IRQ);
 
 	/*
 	 * if the timer irq is not one of the mips irqs we need to

arch/mips/lib/delay.c

@@ -21,7 +21,7 @@ void __delay(unsigned long loops)
 	"	.set	noreorder				\n"
 	"	.align	3					\n"
 	"1:	bnez	%0, 1b					\n"
-#if __SIZEOF_LONG__ == 4
+#if BITS_PER_LONG == 32
 	"	subu	%0, 1					\n"
 #else
 	"	dsubu	%0, 1					\n"

arch/mips/mm/ioremap.c

@@ -190,9 +190,3 @@ void __iounmap(const volatile void __iomem *addr)
 
 EXPORT_SYMBOL(__ioremap);
 EXPORT_SYMBOL(__iounmap);
-
-int __virt_addr_valid(const volatile void *kaddr)
-{
-	return pfn_valid(PFN_DOWN(virt_to_phys(kaddr)));
-}
-EXPORT_SYMBOL_GPL(__virt_addr_valid);

arch/mips/mm/mmap.c

@@ -192,3 +192,9 @@ unsigned long arch_randomize_brk(struct mm_struct *mm)
 
 	return ret;
 }
+
+int __virt_addr_valid(const volatile void *kaddr)
+{
+	return pfn_valid(PFN_DOWN(virt_to_phys(kaddr)));
+}
+EXPORT_SYMBOL_GPL(__virt_addr_valid);

arch/mips/netlogic/xlr/setup.c

@@ -193,8 +193,11 @@ static void nlm_init_node(void)
 
 void __init prom_init(void)
 {
-	int i, *argv, *envp;		/* passed as 32 bit ptrs */
+	int *argv, *envp;		/* passed as 32 bit ptrs */
 	struct psb_info *prom_infop;
+#ifdef CONFIG_SMP
+	int i;
+#endif
 
 	/* truncate to 32 bit and sign extend all args */
 	argv = (int *)(long)(int)fw_arg1;

arch/mips/pci/pci-ar71xx.c

@@ -24,7 +24,7 @@
 #include <asm/mach-ath79/pci.h>
 
 #define AR71XX_PCI_MEM_BASE	0x10000000
-#define AR71XX_PCI_MEM_SIZE	0x08000000
+#define AR71XX_PCI_MEM_SIZE	0x07000000
 
 #define AR71XX_PCI_WIN0_OFFS		0x10000000
 #define AR71XX_PCI_WIN1_OFFS		0x11000000

arch/mips/pci/pci-ar724x.c

@@ -21,7 +21,7 @@
 #define AR724X_PCI_CTRL_SIZE	0x100
 
 #define AR724X_PCI_MEM_BASE	0x10000000
-#define AR724X_PCI_MEM_SIZE	0x08000000
+#define AR724X_PCI_MEM_SIZE	0x04000000
 
 #define AR724X_PCI_REG_RESET		0x18
 #define AR724X_PCI_REG_INT_STATUS	0x4c

arch/mn10300/include/asm/dma-mapping.h

@@ -168,4 +168,19 @@ void dma_cache_sync(void *vaddr, size_t size,
 	mn10300_dcache_flush_inv();
 }
 
+/* Not supported for now */
+static inline int dma_mmap_coherent(struct device *dev,
+				    struct vm_area_struct *vma, void *cpu_addr,
+				    dma_addr_t dma_addr, size_t size)
+{
+	return -EINVAL;
+}
+
+static inline int dma_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size)
+{
+	return -EINVAL;
+}
+
 #endif

arch/parisc/include/asm/dma-mapping.h

@@ -238,4 +238,19 @@ void * sba_get_iommu(struct parisc_device *dev);
 /* At the moment, we panic on error for IOMMU resource exaustion */
 #define dma_mapping_error(dev, x)	0
 
+/* This API cannot be supported on PA-RISC */
+static inline int dma_mmap_coherent(struct device *dev,
+				    struct vm_area_struct *vma, void *cpu_addr,
+				    dma_addr_t dma_addr, size_t size)
+{
+	return -EINVAL;
+}
+
+static inline int dma_get_sgtable(struct device *dev, struct sg_table *sgt,
+				  void *cpu_addr, dma_addr_t dma_addr,
+				  size_t size)
+{
+	return -EINVAL;
+}
+
 #endif

arch/powerpc/kernel/entry_32.S

@@ -439,6 +439,8 @@ ret_from_fork:
 ret_from_kernel_thread:
 	REST_NVGPRS(r1)
 	bl	schedule_tail
+	li	r3,0
+	stw	r3,0(r1)
 	mtlr	r14
 	mr	r3,r15
 	PPC440EP_ERR42

arch/powerpc/kernel/entry_64.S

@@ -664,6 +664,19 @@ resume_kernel:
 	ld	r4,TI_FLAGS(r9)
 	andi.	r0,r4,_TIF_NEED_RESCHED
 	bne	1b
+
+	/*
+	 * arch_local_irq_restore() from preempt_schedule_irq above may
+	 * enable hard interrupt but we really should disable interrupts
+	 * when we return from the interrupt, and so that we don't get
+	 * interrupted after loading SRR0/1.
+	 */
+#ifdef CONFIG_PPC_BOOK3E
+	wrteei	0
+#else
+	ld	r10,PACAKMSR(r13) /* Get kernel MSR without EE */
+	mtmsrd	r10,1		  /* Update machine state */
+#endif /* CONFIG_PPC_BOOK3E */
 #endif /* CONFIG_PREEMPT */
 
 	.globl	fast_exc_return_irq

arch/powerpc/kernel/kgdb.c

@@ -154,12 +154,12 @@ static int kgdb_handle_breakpoint(struct pt_regs *regs)
 static int kgdb_singlestep(struct pt_regs *regs)
 {
 	struct thread_info *thread_info, *exception_thread_info;
-	struct thread_info *backup_current_thread_info = \
-		(struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL);
+	struct thread_info *backup_current_thread_info;
 
 	if (user_mode(regs))
 		return 0;
 
+	backup_current_thread_info = (struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL);
 	/*
 	 * On Book E and perhaps other processors, singlestep is handled on
 	 * the critical exception stack.  This causes current_thread_info()
@@ -185,6 +185,7 @@ static int kgdb_singlestep(struct pt_regs *regs)
 		/* Restore current_thread_info lastly. */
 		memcpy(exception_thread_info, backup_current_thread_info, sizeof *thread_info);
 
+	kfree(backup_current_thread_info);
 	return 1;
 }
 

arch/powerpc/kernel/time.c

@@ -494,10 +494,15 @@ void timer_interrupt(struct pt_regs * regs)
 	set_dec(DECREMENTER_MAX);
 
 	/* Some implementations of hotplug will get timer interrupts while
-	 * offline, just ignore these
+	 * offline, just ignore these and we also need to set
+	 * decrementers_next_tb as MAX to make sure __check_irq_replay
+	 * don't replay timer interrupt when return, otherwise we'll trap
+	 * here infinitely :(
 	 */
-	if (!cpu_online(smp_processor_id()))
+	if (!cpu_online(smp_processor_id())) {
+		*next_tb = ~(u64)0;
 		return;
+	}
 
 	/* Conditionally hard-enable interrupts now that the DEC has been
 	 * bumped to its maximum value

arch/powerpc/kvm/emulate.c

@@ -39,6 +39,7 @@
 #define OP_31_XOP_TRAP      4
 #define OP_31_XOP_LWZX      23
 #define OP_31_XOP_TRAP_64   68
+#define OP_31_XOP_DCBF      86
 #define OP_31_XOP_LBZX      87
 #define OP_31_XOP_STWX      151
 #define OP_31_XOP_STBX      215
@@ -374,6 +375,7 @@ int kvmppc_emulate_instruction(struct kvm_run *run, struct kvm_vcpu *vcpu)
 			emulated = kvmppc_emulate_mtspr(vcpu, sprn, rs);
 			break;
 
+		case OP_31_XOP_DCBF:
 		case OP_31_XOP_DCBI:
 			/* Do nothing. The guest is performing dcbi because
 			 * hardware DMA is not snooped by the dcache, but

arch/powerpc/mm/hash_low_64.S

@@ -115,11 +115,13 @@ END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	sldi	r29,r5,SID_SHIFT - VPN_SHIFT
 	rldicl  r28,r3,64 - VPN_SHIFT,64 - (SID_SHIFT - VPN_SHIFT)
 	or	r29,r28,r29
-
-	/* Calculate hash value for primary slot and store it in r28 */
-	rldicl	r5,r5,0,25		/* vsid & 0x0000007fffffffff */
-	rldicl	r0,r3,64-12,48		/* (ea >> 12) & 0xffff */
-	xor	r28,r5,r0
+	/*
+	 * Calculate hash value for primary slot and store it in r28
+	 * r3 = va, r5 = vsid
+	 * r0 = (va >> 12) & ((1ul << (28 - 12)) -1)
+	 */
+	rldicl	r0,r3,64-12,48
+	xor	r28,r5,r0		/* hash */
 	b	4f
 
 3:	/* Calc vpn and put it in r29 */
@@ -130,11 +132,12 @@ END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	/*
 	 * calculate hash value for primary slot and
 	 * store it in r28 for 1T segment
+	 * r3 = va, r5 = vsid
 	 */
-	rldic	r28,r5,25,25		/* (vsid << 25) & 0x7fffffffff */
-	clrldi	r5,r5,40		/* vsid & 0xffffff */
-	rldicl	r0,r3,64-12,36		/* (ea >> 12) & 0xfffffff */
-	xor	r28,r28,r5
+	sldi	r28,r5,25		/* vsid << 25 */
+	/* r0 =  (va >> 12) & ((1ul << (40 - 12)) -1) */
+	rldicl	r0,r3,64-12,36
+	xor	r28,r28,r5		/* vsid ^ ( vsid << 25) */
 	xor	r28,r28,r0		/* hash */
 
 	/* Convert linux PTE bits into HW equivalents */
@@ -407,11 +410,13 @@ END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	 */
 	rldicl  r28,r3,64 - VPN_SHIFT,64 - (SID_SHIFT - VPN_SHIFT)
 	or	r29,r28,r29
-
-	/* Calculate hash value for primary slot and store it in r28 */
-	rldicl	r5,r5,0,25		/* vsid & 0x0000007fffffffff */
-	rldicl	r0,r3,64-12,48		/* (ea >> 12) & 0xffff */
-	xor	r28,r5,r0
+	/*
+	 * Calculate hash value for primary slot and store it in r28
+	 * r3 = va, r5 = vsid
+	 * r0 = (va >> 12) & ((1ul << (28 - 12)) -1)
+	 */
+	rldicl	r0,r3,64-12,48
+	xor	r28,r5,r0		/* hash */
 	b	4f
 
 3:	/* Calc vpn and put it in r29 */
@@ -426,11 +431,12 @@ END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	/*
 	 * Calculate hash value for primary slot and
 	 * store it in r28  for 1T segment
+	 * r3 = va, r5 = vsid
 	 */
-	rldic	r28,r5,25,25		/* (vsid << 25) & 0x7fffffffff */
-	clrldi	r5,r5,40		/* vsid & 0xffffff */
-	rldicl	r0,r3,64-12,36		/* (ea >> 12) & 0xfffffff */
-	xor	r28,r28,r5
+	sldi	r28,r5,25		/* vsid << 25 */
+	/* r0 = (va >> 12) & ((1ul << (40 - 12)) -1) */
+	rldicl	r0,r3,64-12,36
+	xor	r28,r28,r5		/* vsid ^ ( vsid << 25) */
 	xor	r28,r28,r0		/* hash */
 
 	/* Convert linux PTE bits into HW equivalents */
@@ -752,25 +758,27 @@ END_MMU_FTR_SECTION_IFSET(MMU_FTR_1T_SEGMENT)
 	rldicl  r28,r3,64 - VPN_SHIFT,64 - (SID_SHIFT - VPN_SHIFT)
 	or	r29,r28,r29
 
-	/* Calculate hash value for primary slot and store it in r28 */
-	rldicl	r5,r5,0,25		/* vsid & 0x0000007fffffffff */
-	rldicl	r0,r3,64-16,52		/* (ea >> 16) & 0xfff */
-	xor	r28,r5,r0
+	/* Calculate hash value for primary slot and store it in r28
+	 * r3 = va, r5 = vsid
+	 * r0 = (va >> 16) & ((1ul << (28 - 16)) -1)
+	 */
+	rldicl	r0,r3,64-16,52
+	xor	r28,r5,r0		/* hash */
 	b	4f
 
 3:	/* Calc vpn and put it in r29 */
 	sldi	r29,r5,SID_SHIFT_1T - VPN_SHIFT
 	rldicl  r28,r3,64 - VPN_SHIFT,64 - (SID_SHIFT_1T - VPN_SHIFT)
 	or	r29,r28,r29
-
 	/*
 	 * calculate hash value for primary slot and
 	 * store it in r28 for 1T segment
+	 * r3 = va, r5 = vsid
 	 */
-	rldic	r28,r5,25,25		/* (vsid << 25) & 0x7fffffffff */
-	clrldi	r5,r5,40		/* vsid & 0xffffff */
-	rldicl	r0,r3,64-16,40		/* (ea >> 16) & 0xffffff */
-	xor	r28,r28,r5
+	sldi	r28,r5,25		/* vsid << 25 */
+	/* r0 = (va >> 16) & ((1ul << (40 - 16)) -1) */
+	rldicl	r0,r3,64-16,40
+	xor	r28,r28,r5		/* vsid ^ ( vsid << 25) */
 	xor	r28,r28,r0		/* hash */
 
 	/* Convert linux PTE bits into HW equivalents */

arch/powerpc/oprofile/op_model_power4.c

@@ -52,7 +52,7 @@ static int power7_marked_instr_event(u64 mmcr1)
 	for (pmc = 0; pmc < 4; pmc++) {
 		psel = mmcr1 & (OPROFILE_PM_PMCSEL_MSK
 				<< (OPROFILE_MAX_PMC_NUM - pmc)
-				* OPROFILE_MAX_PMC_NUM);
+				* OPROFILE_PMSEL_FIELD_WIDTH);
 		psel = (psel >> ((OPROFILE_MAX_PMC_NUM - pmc)
 				 * OPROFILE_PMSEL_FIELD_WIDTH)) & ~1ULL;
 		unit = mmcr1 & (OPROFILE_PM_UNIT_MSK

arch/powerpc/platforms/pasemi/cpufreq.c

@@ -236,6 +236,13 @@ out:
 
 static int pas_cpufreq_cpu_exit(struct cpufreq_policy *policy)
 {
+	/*
+	 * We don't support CPU hotplug. Don't unmap after the system
+	 * has already made it to a running state.
+	 */
+	if (system_state != SYSTEM_BOOTING)
+		return 0;
+
 	if (sdcasr_mapbase)
 		iounmap(sdcasr_mapbase);
 	if (sdcpwr_mapbase)

arch/s390/include/asm/pgtable.h

@@ -1365,6 +1365,18 @@ static inline void pmdp_invalidate(struct vm_area_struct *vma,
 	__pmd_idte(address, pmdp);
 }
 
+#define __HAVE_ARCH_PMDP_SET_WRPROTECT
+static inline void pmdp_set_wrprotect(struct mm_struct *mm,
+				      unsigned long address, pmd_t *pmdp)
+{
+	pmd_t pmd = *pmdp;
+
+	if (pmd_write(pmd)) {
+		__pmd_idte(address, pmdp);
+		set_pmd_at(mm, address, pmdp, pmd_wrprotect(pmd));
+	}
+}
+
 static inline pmd_t mk_pmd_phys(unsigned long physpage, pgprot_t pgprot)
 {
 	pmd_t __pmd;

arch/x86/Kconfig

@@ -2139,6 +2139,7 @@ config OLPC_XO1_RTC
 config OLPC_XO1_SCI
 	bool "OLPC XO-1 SCI extras"
 	depends on OLPC && OLPC_XO1_PM
+	depends on INPUT=y
 	select POWER_SUPPLY
 	select GPIO_CS5535
 	select MFD_CORE

arch/x86/boot/Makefile

@@ -71,7 +71,7 @@ GCOV_PROFILE := n
 $(obj)/bzImage: asflags-y  := $(SVGA_MODE)
 
 quiet_cmd_image = BUILD   $@
-cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin > $@
+cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/zoffset.h > $@
 
 $(obj)/bzImage: $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/tools/build FORCE
 	$(call if_changed,image)
@@ -92,7 +92,7 @@ targets += voffset.h
 $(obj)/voffset.h: vmlinux FORCE
 	$(call if_changed,voffset)
 
-sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p'
+sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|startup_64\|efi_pe_entry\|efi_stub_entry\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p'
 
 quiet_cmd_zoffset = ZOFFSET $@
       cmd_zoffset = $(NM) $< | sed -n $(sed-zoffset) > $@

arch/x86/boot/compressed/eboot.c

@@ -256,10 +256,10 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
 	int i;
 	struct setup_data *data;
 
-	data = (struct setup_data *)params->hdr.setup_data;
+	data = (struct setup_data *)(unsigned long)params->hdr.setup_data;
 
 	while (data && data->next)
-		data = (struct setup_data *)data->next;
+		data = (struct setup_data *)(unsigned long)data->next;
 
 	status = efi_call_phys5(sys_table->boottime->locate_handle,
 				EFI_LOCATE_BY_PROTOCOL, &pci_proto,
@@ -295,16 +295,18 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
 		if (!pci)
 			continue;
 
+#ifdef CONFIG_X86_64
 		status = efi_call_phys4(pci->attributes, pci,
 					EfiPciIoAttributeOperationGet, 0,
 					&attributes);
-
+#else
+		status = efi_call_phys5(pci->attributes, pci,
+					EfiPciIoAttributeOperationGet, 0, 0,
+					&attributes);
+#endif
 		if (status != EFI_SUCCESS)
 			continue;
 
-		if (!(attributes & EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM))
-			continue;
-
 		if (!pci->romimage || !pci->romsize)
 			continue;
 
@@ -345,9 +347,9 @@ static efi_status_t setup_efi_pci(struct boot_params *params)
 		memcpy(rom->romdata, pci->romimage, pci->romsize);
 
 		if (data)
-			data->next = (uint64_t)rom;
+			data->next = (unsigned long)rom;
 		else
-			params->hdr.setup_data = (uint64_t)rom;
+			params->hdr.setup_data = (unsigned long)rom;
 
 		data = (struct setup_data *)rom;
 
@@ -432,10 +434,9 @@ static efi_status_t setup_gop(struct screen_info *si, efi_guid_t *proto,
 			 * Once we've found a GOP supporting ConOut,
 			 * don't bother looking any further.
 			 */
+			first_gop = gop;
 			if (conout_found)
 				break;
-
-			first_gop = gop;
 		}
 	}
 

arch/x86/boot/compressed/head_32.S

@@ -35,11 +35,11 @@ ENTRY(startup_32)
 #ifdef CONFIG_EFI_STUB
 	jmp	preferred_addr
 
-	.balign	0x10
 	/*
 	 * We don't need the return address, so set up the stack so
-	 * efi_main() can find its arugments.
+	 * efi_main() can find its arguments.
 	 */
+ENTRY(efi_pe_entry)
 	add	$0x4, %esp
 
 	call	make_boot_params
@@ -50,8 +50,10 @@ ENTRY(startup_32)
 	pushl	%eax
 	pushl	%esi
 	pushl	%ecx
+	sub	$0x4, %esp
 
-	.org 0x30,0x90
+ENTRY(efi_stub_entry)
+	add	$0x4, %esp
 	call	efi_main
 	cmpl	$0, %eax
 	movl	%eax, %esi

arch/x86/boot/compressed/head_64.S

@@ -201,12 +201,12 @@ ENTRY(startup_64)
 	 */
 #ifdef CONFIG_EFI_STUB
 	/*
-	 * The entry point for the PE/COFF executable is 0x210, so only
-	 * legacy boot loaders will execute this jmp.
+	 * The entry point for the PE/COFF executable is efi_pe_entry, so
+	 * only legacy boot loaders will execute this jmp.
 	 */
 	jmp	preferred_addr
 
-	.org 0x210
+ENTRY(efi_pe_entry)
 	mov	%rcx, %rdi
 	mov	%rdx, %rsi
 	pushq	%rdi
@@ -218,7 +218,7 @@ ENTRY(startup_64)
 	popq	%rsi
 	popq	%rdi
 
-	.org 0x230,0x90
+ENTRY(efi_stub_entry)
 	call	efi_main
 	movq	%rax,%rsi
 	cmpq	$0,%rax

arch/x86/boot/header.S

@@ -21,6 +21,7 @@
 #include <asm/e820.h>
 #include <asm/page_types.h>
 #include <asm/setup.h>
+#include <asm/bootparam.h>
 #include "boot.h"
 #include "voffset.h"
 #include "zoffset.h"
@@ -255,6 +256,9 @@ section_table:
 	# header, from the old boot sector.
 
 	.section ".header", "a"
+	.globl	sentinel
+sentinel:	.byte 0xff, 0xff        /* Used to detect broken loaders */
+
 	.globl	hdr
 hdr:
 setup_sects:	.byte 0			/* Filled in by build.c */
@@ -279,7 +283,7 @@ _start:
 	# Part 2 of the header, from the old setup.S
 
 		.ascii	"HdrS"		# header signature
-		.word	0x020b		# header version number (>= 0x0105)
+		.word	0x020c		# header version number (>= 0x0105)
 					# or else old loadlin-1.5 will fail)
 		.globl realmode_swtch
 realmode_swtch:	.word	0, 0		# default_switch, SETUPSEG
@@ -297,13 +301,7 @@ type_of_loader:	.byte	0		# 0 means ancient bootloader, newer
 
 # flags, unused bits must be zero (RFU) bit within loadflags
 loadflags:
-LOADED_HIGH	= 1			# If set, the kernel is loaded high
-CAN_USE_HEAP	= 0x80			# If set, the loader also has set
-					# heap_end_ptr to tell how much
-					# space behind setup.S can be used for
-					# heap purposes.
-					# Only the loader knows what is free
-		.byte	LOADED_HIGH
+		.byte	LOADED_HIGH	# The kernel is to be loaded high
 
 setup_move_size: .word  0x8000		# size to move, when setup is not
 					# loaded at 0x90000. We will move setup
@@ -369,7 +367,23 @@ relocatable_kernel:    .byte 1
 relocatable_kernel:    .byte 0
 #endif
 min_alignment:		.byte MIN_KERNEL_ALIGN_LG2	# minimum alignment
-pad3:			.word 0
+
+xloadflags:
+#ifdef CONFIG_X86_64
+# define XLF0 XLF_KERNEL_64			/* 64-bit kernel */
+#else
+# define XLF0 0
+#endif
+#ifdef CONFIG_EFI_STUB
+# ifdef CONFIG_X86_64
+#  define XLF23 XLF_EFI_HANDOVER_64		/* 64-bit EFI handover ok */
+# else
+#  define XLF23 XLF_EFI_HANDOVER_32		/* 32-bit EFI handover ok */
+# endif
+#else
+# define XLF23 0
+#endif
+			.word XLF0 | XLF23
 
 cmdline_size:   .long   COMMAND_LINE_SIZE-1     #length of the command line,
                                                 #added with boot protocol
@@ -397,8 +411,13 @@ pref_address:		.quad LOAD_PHYSICAL_ADDR	# preferred load addr
 #define INIT_SIZE VO_INIT_SIZE
 #endif
 init_size:		.long INIT_SIZE		# kernel initialization size
-handover_offset:	.long 0x30		# offset to the handover
+handover_offset:
+#ifdef CONFIG_EFI_STUB
+  			.long 0x30		# offset to the handover
 						# protocol entry point
+#else
+			.long 0
+#endif
 
 # End of setup header #####################################################
 

arch/x86/boot/setup.ld

@@ -13,7 +13,7 @@ SECTIONS
 	.bstext		: { *(.bstext) }
 	.bsdata		: { *(.bsdata) }
 
-	. = 497;
+	. = 495;
 	.header		: { *(.header) }
 	.entrytext	: { *(.entrytext) }
 	.inittext	: { *(.inittext) }

arch/x86/boot/tools/build.c

@@ -52,6 +52,10 @@ int is_big_kernel;
 
 #define PECOFF_RELOC_RESERVE 0x20
 
+unsigned long efi_stub_entry;
+unsigned long efi_pe_entry;
+unsigned long startup_64;
+
 /*----------------------------------------------------------------------*/
 
 static const u32 crctab32[] = {
@@ -132,7 +136,7 @@ static void die(const char * str, ...)
 
 static void usage(void)
 {
-	die("Usage: build setup system [> image]");
+	die("Usage: build setup system [zoffset.h] [> image]");
 }
 
 #ifdef CONFIG_EFI_STUB
@@ -206,30 +210,54 @@ static void update_pecoff_text(unsigned int text_start, unsigned int file_sz)
 	 */
 	put_unaligned_le32(file_sz - 512, &buf[pe_header + 0x1c]);
 
-#ifdef CONFIG_X86_32
 	/*
-	 * Address of entry point.
-	 *
-	 * The EFI stub entry point is +16 bytes from the start of
-	 * the .text section.
+	 * Address of entry point for PE/COFF executable
 	 */
-	put_unaligned_le32(text_start + 16, &buf[pe_header + 0x28]);
-#else
-	/*
-	 * Address of entry point. startup_32 is at the beginning and
-	 * the 64-bit entry point (startup_64) is always 512 bytes
-	 * after. The EFI stub entry point is 16 bytes after that, as
-	 * the first instruction allows legacy loaders to jump over
-	 * the EFI stub initialisation
-	 */
-	put_unaligned_le32(text_start + 528, &buf[pe_header + 0x28]);
-#endif /* CONFIG_X86_32 */
+	put_unaligned_le32(text_start + efi_pe_entry, &buf[pe_header + 0x28]);
 
 	update_pecoff_section_header(".text", text_start, text_sz);
 }
 
 #endif /* CONFIG_EFI_STUB */
 
+
+/*
+ * Parse zoffset.h and find the entry points. We could just #include zoffset.h
+ * but that would mean tools/build would have to be rebuilt every time. It's
+ * not as if parsing it is hard...
+ */
+#define PARSE_ZOFS(p, sym) do { \
+	if (!strncmp(p, "#define ZO_" #sym " ", 11+sizeof(#sym)))	\
+		sym = strtoul(p + 11 + sizeof(#sym), NULL, 16);		\
+} while (0)
+
+static void parse_zoffset(char *fname)
+{
+	FILE *file;
+	char *p;
+	int c;
+
+	file = fopen(fname, "r");
+	if (!file)
+		die("Unable to open `%s': %m", fname);
+	c = fread(buf, 1, sizeof(buf) - 1, file);
+	if (ferror(file))
+		die("read-error on `zoffset.h'");
+	buf[c] = 0;
+
+	p = (char *)buf;
+
+	while (p && *p) {
+		PARSE_ZOFS(p, efi_stub_entry);
+		PARSE_ZOFS(p, efi_pe_entry);
+		PARSE_ZOFS(p, startup_64);
+
+		p = strchr(p, '\n');
+		while (p && (*p == '\r' || *p == '\n'))
+			p++;
+	}
+}
+
 int main(int argc, char ** argv)
 {
 	unsigned int i, sz, setup_sectors;
@@ -241,7 +269,19 @@ int main(int argc, char ** argv)
 	void *kernel;
 	u32 crc = 0xffffffffUL;
 
-	if (argc != 3)
+	/* Defaults for old kernel */
+#ifdef CONFIG_X86_32
+	efi_pe_entry = 0x10;
+	efi_stub_entry = 0x30;
+#else
+	efi_pe_entry = 0x210;
+	efi_stub_entry = 0x230;
+	startup_64 = 0x200;
+#endif
+
+	if (argc == 4)
+		parse_zoffset(argv[3]);
+	else if (argc != 3)
 		usage();
 
 	/* Copy the setup code */
@@ -299,6 +339,11 @@ int main(int argc, char ** argv)
 
 #ifdef CONFIG_EFI_STUB
 	update_pecoff_text(setup_sectors * 512, sz + i + ((sys_size * 16) - sz));
+
+#ifdef CONFIG_X86_64 /* Yes, this is really how we defined it :( */
+	efi_stub_entry -= 0x200;
+#endif
+	put_unaligned_le32(efi_stub_entry, &buf[0x264]);
 #endif
 
 	crc = partial_crc32(buf, i, crc);

arch/x86/ia32/ia32entry.S

@@ -207,7 +207,7 @@ sysexit_from_sys_call:
 	testl $(_TIF_ALLWORK_MASK & ~_TIF_SYSCALL_AUDIT),TI_flags+THREAD_INFO(%rsp,RIP-ARGOFFSET)
 	jnz ia32_ret_from_sys_call
 	TRACE_IRQS_ON
-	sti
+	ENABLE_INTERRUPTS(CLBR_NONE)
 	movl %eax,%esi		/* second arg, syscall return value */
 	cmpl $-MAX_ERRNO,%eax	/* is it an error ? */
 	jbe 1f
@@ -217,7 +217,7 @@ sysexit_from_sys_call:
 	call __audit_syscall_exit
 	movq RAX-ARGOFFSET(%rsp),%rax	/* reload syscall return value */
 	movl $(_TIF_ALLWORK_MASK & ~_TIF_SYSCALL_AUDIT),%edi
-	cli
+	DISABLE_INTERRUPTS(CLBR_NONE)
 	TRACE_IRQS_OFF
 	testl %edi,TI_flags+THREAD_INFO(%rsp,RIP-ARGOFFSET)
 	jz \exit