[ARM] pxa: move DMA registers definitions into <mach/dma.h>

1. Driver code where pxa_request_dma() is called will most likely
   reference DMA registers as well,  and it is really unnecessary
   to include pxa-regs.h just for this. Move the definitions into
   <mach/dma.h> and make relevant drivers include it instead of
   <mach/pxa-regs.h>.

2. Introduce DMAC_REGS_VIRT as the virtual address base for these
   DMA registers. This allows later processors to re-use the same
   IP while registers may start at different I/O address.

Signed-off-by: Eric Miao <eric.miao@marvell.com>

arch/arm/mach-pxa/dma.c

@@ -23,8 +23,6 @@
 #include <mach/hardware.h>
 #include <mach/dma.h>
 
-#include <mach/pxa-regs.h>
-
 struct dma_channel {
 	char *name;
 	pxa_dma_prio prio;

arch/arm/mach-pxa/include/mach/dma.h

@@ -12,6 +12,62 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H
 
+#include <mach/hardware.h>
+
+/* DMA Controller Registers Definitions */
+#define DMAC_REGS_VIRT	io_p2v(0x40000000)
+#define DMAC_REG(x)	(*((volatile u32 *)(DMAC_REGS_VIRT + (x))))
+
+#define DCSR(n)		DMAC_REG((n) << 2)
+#define DALGN		DMAC_REG(0x00a0)  /* DMA Alignment Register */
+#define DINT		DMAC_REG(0x00f0)  /* DMA Interrupt Register */
+#define DDADR(n)	DMAC_REG(0x0200 + ((n) << 4))
+#define DSADR(n)	DMAC_REG(0x0204 + ((n) << 4))
+#define DTADR(n)	DMAC_REG(0x0208 + ((n) << 4))
+#define DCMD(n)		DMAC_REG(0x020c + ((n) << 4))
+#define DRCMR(n)	DMAC_REG((((n) < 64) ? 0x0100 : 0x1100) + \
+				 (((n) & 0x3f) << 2))
+
+#define DCSR_RUN	(1 << 31)	/* Run Bit (read / write) */
+#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch (read / write) */
+#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable (read / write) */
+#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
+#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
+#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt (read / write) */
+#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt (read / write) */
+#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt (read / write) */
+
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+#define DCSR_EORIRQEN	(1 << 28)       /* End of Receive Interrupt Enable (R/W) */
+#define DCSR_EORJMPEN	(1 << 27)       /* Jump to next descriptor on EOR */
+#define DCSR_EORSTOPEN	(1 << 26)       /* STOP on an EOR */
+#define DCSR_SETCMPST	(1 << 25)       /* Set Descriptor Compare Status */
+#define DCSR_CLRCMPST	(1 << 24)       /* Clear Descriptor Compare Status */
+#define DCSR_CMPST	(1 << 10)       /* The Descriptor Compare Status */
+#define DCSR_EORINTR	(1 << 9)        /* The end of Receive */
+#endif
+
+#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid (read / write) */
+#define DRCMR_CHLNUM	0x1f		/* mask for Channel Number (read / write) */
+
+#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor (mask) */
+#define DDADR_STOP	(1 << 0)	/* Stop (read / write) */
+
+#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
+#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
+#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
+#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
+#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
+#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
+#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
+#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
+#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
+#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
+#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
+#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
+#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
+#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
+
 /*
  * Descriptor structure for PXA's DMA engine
  * Note: this structure must always be aligned to a 16-byte boundary.

arch/arm/mach-pxa/include/mach/pxa-regs.h

@@ -65,65 +65,6 @@
 #define _PCMCIA1Attr	_PCMCIAAttr (1)	/* PCMCIA 1 Attribute              */
 #define _PCMCIA1Mem	_PCMCIAMem (1)	/* PCMCIA 1 Memory                 */
 
-
-
-/*
- * DMA Controller
- */
-#define DCSR(x)		__REG2(0x40000000, (x) << 2)
-
-#define DCSR_RUN	(1 << 31)	/* Run Bit (read / write) */
-#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch (read / write) */
-#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable (read / write) */
-#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
-#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
-#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt (read / write) */
-#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt (read / write) */
-#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt (read / write) */
-
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#define DCSR_EORIRQEN	(1 << 28)       /* End of Receive Interrupt Enable (R/W) */
-#define DCSR_EORJMPEN	(1 << 27)       /* Jump to next descriptor on EOR */
-#define DCSR_EORSTOPEN	(1 << 26)       /* STOP on an EOR */
-#define DCSR_SETCMPST	(1 << 25)       /* Set Descriptor Compare Status */
-#define DCSR_CLRCMPST	(1 << 24)       /* Clear Descriptor Compare Status */
-#define DCSR_CMPST	(1 << 10)       /* The Descriptor Compare Status */
-#define DCSR_EORINTR	(1 << 9)        /* The end of Receive */
-#endif
-
-#define DALGN		__REG(0x400000a0)  /* DMA Alignment Register */
-#define DINT		__REG(0x400000f0)  /* DMA Interrupt Register */
-
-#define DRCMR(n)	(*(((n) < 64) ? \
-			&__REG2(0x40000100, ((n) & 0x3f) << 2) : \
-			&__REG2(0x40001100, ((n) & 0x3f) << 2)))
-
-#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid (read / write) */
-#define DRCMR_CHLNUM	0x1f		/* mask for Channel Number (read / write) */
-
-#define DDADR(x)	__REG2(0x40000200, (x) << 4)
-#define DSADR(x)	__REG2(0x40000204, (x) << 4)
-#define DTADR(x)	__REG2(0x40000208, (x) << 4)
-#define DCMD(x)		__REG2(0x4000020c, (x) << 4)
-
-#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor (mask) */
-#define DDADR_STOP	(1 << 0)	/* Stop (read / write) */
-
-#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
-#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
-#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
-#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
-#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
-#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
-#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
-#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
-#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
-#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
-#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
-#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
-#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
-#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
-
 /*
  * Real Time Clock
  */

drivers/media/video/pxa_camera.c

@@ -35,7 +35,6 @@
 #include <linux/videodev2.h>
 
 #include <mach/dma.h>
-#include <mach/pxa-regs.h>
 #include <mach/camera.h>
 
 #define PXA_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5)

drivers/mmc/host/pxamci.c

@@ -30,9 +30,8 @@
 
 #include <asm/sizes.h>
 
-#include <mach/dma.h>
 #include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
 #include <mach/mmc.h>
 
 #include "pxamci.h"

drivers/mtd/nand/pxa3xx_nand.c

@@ -22,7 +22,6 @@
 #include <linux/irq.h>
 
 #include <mach/dma.h>
-#include <mach/pxa-regs.h>
 #include <mach/pxa3xx_nand.h>
 
 #define	CHIP_DELAY_TIMEOUT	(2 * HZ/10)

drivers/spi/pxa2xx_spi.c

@@ -34,8 +34,6 @@
 #include <asm/delay.h>
 
 #include <mach/dma.h>
-#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
 #include <mach/regs-ssp.h>
 #include <mach/ssp.h>
 #include <mach/pxa2xx_spi.h>

sound/soc/pxa/pxa-ssp.c

@@ -29,7 +29,7 @@
 #include <sound/pxa2xx-lib.h>
 
 #include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
 #include <mach/regs-ssp.h>
 #include <mach/audio.h>
 #include <mach/ssp.h>

sound/soc/pxa/pxa2xx-ac97.c

@@ -20,8 +20,8 @@
 #include <sound/pxa2xx-lib.h>
 
 #include <mach/hardware.h>
-#include <mach/pxa-regs.h>
 #include <mach/regs-ac97.h>
+#include <mach/dma.h>
 
 #include "pxa2xx-pcm.h"
 #include "pxa2xx-ac97.h"

sound/soc/pxa/pxa2xx-i2s.c

@@ -24,7 +24,7 @@
 #include <sound/pxa2xx-lib.h>
 
 #include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
 #include <mach/pxa2xx-gpio.h>
 #include <mach/audio.h>