Merge branch 'upstream' of git://lost.foo-projects.org/~ahkok/git/netdev-2.6 into upstream

drivers/net/e100.c

@@ -159,7 +159,7 @@
 
 #define DRV_NAME		"e100"
 #define DRV_EXT			"-NAPI"
-#define DRV_VERSION		"3.5.10-k4"DRV_EXT
+#define DRV_VERSION		"3.5.16-k2"DRV_EXT
 #define DRV_DESCRIPTION		"Intel(R) PRO/100 Network Driver"
 #define DRV_COPYRIGHT		"Copyright(c) 1999-2006 Intel Corporation"
 #define PFX			DRV_NAME ": "
@@ -1759,11 +1759,10 @@ static inline void e100_start_receiver(struct nic *nic, struct rx *rx)
 #define RFD_BUF_LEN (sizeof(struct rfd) + VLAN_ETH_FRAME_LEN)
 static int e100_rx_alloc_skb(struct nic *nic, struct rx *rx)
 {
-	if(!(rx->skb = dev_alloc_skb(RFD_BUF_LEN + NET_IP_ALIGN)))
+	if(!(rx->skb = netdev_alloc_skb(nic->netdev, RFD_BUF_LEN + NET_IP_ALIGN)))
 		return -ENOMEM;
 
 	/* Align, init, and map the RFD. */
-	rx->skb->dev = nic->netdev;
 	skb_reserve(rx->skb, NET_IP_ALIGN);
 	memcpy(rx->skb->data, &nic->blank_rfd, sizeof(struct rfd));
 	rx->dma_addr = pci_map_single(nic->pdev, rx->skb->data,
@@ -2139,7 +2138,7 @@ static int e100_loopback_test(struct nic *nic, enum loopback loopback_mode)
 
 	e100_start_receiver(nic, NULL);
 
-	if(!(skb = dev_alloc_skb(ETH_DATA_LEN))) {
+	if(!(skb = netdev_alloc_skb(nic->netdev, ETH_DATA_LEN))) {
 		err = -ENOMEM;
 		goto err_loopback_none;
 	}
@@ -2791,6 +2790,7 @@ static pci_ers_result_t e100_io_error_detected(struct pci_dev *pdev, pci_channel
 	/* Detach; put netif into state similar to hotplug unplug. */
 	netif_poll_enable(netdev);
 	netif_device_detach(netdev);
+	pci_disable_device(pdev);
 
 	/* Request a slot reset. */
 	return PCI_ERS_RESULT_NEED_RESET;

drivers/net/e1000/e1000.h

@@ -242,12 +242,10 @@ struct e1000_adapter {
 	struct timer_list watchdog_timer;
 	struct timer_list phy_info_timer;
 	struct vlan_group *vlgrp;
-    	uint16_t mng_vlan_id;
+	uint16_t mng_vlan_id;
 	uint32_t bd_number;
 	uint32_t rx_buffer_len;
-	uint32_t part_num;
 	uint32_t wol;
-	uint32_t ksp3_port_a;
 	uint32_t smartspeed;
 	uint32_t en_mng_pt;
 	uint16_t link_speed;
@@ -342,7 +340,9 @@ struct e1000_adapter {
 	boolean_t tso_force;
 #endif
 	boolean_t smart_power_down;	/* phy smart power down */
+	boolean_t quad_port_a;
 	unsigned long flags;
+	uint32_t eeprom_wol;
 };
 
 enum e1000_state_t {

drivers/net/e1000/e1000_ethtool.c

@@ -428,12 +428,12 @@ e1000_get_regs(struct net_device *netdev,
 		regs_buff[23] = regs_buff[18]; /* mdix mode */
 		e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
 	} else {
-        	e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+		e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
 		regs_buff[13] = (uint32_t)phy_data; /* cable length */
 		regs_buff[14] = 0;  /* Dummy (to align w/ IGP phy reg dump) */
 		regs_buff[15] = 0;  /* Dummy (to align w/ IGP phy reg dump) */
 		regs_buff[16] = 0;  /* Dummy (to align w/ IGP phy reg dump) */
-        	e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+		e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
 		regs_buff[17] = (uint32_t)phy_data; /* extended 10bt distance */
 		regs_buff[18] = regs_buff[13]; /* cable polarity */
 		regs_buff[19] = 0;  /* Dummy (to align w/ IGP phy reg dump) */
@@ -709,7 +709,6 @@ e1000_set_ringparam(struct net_device *netdev,
 	}
 
 	clear_bit(__E1000_RESETTING, &adapter->flags);
-
 	return 0;
 err_setup_tx:
 	e1000_free_all_rx_resources(adapter);
@@ -894,16 +893,17 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
 
 	*data = 0;
 
+	/* NOTE: we don't test MSI interrupts here, yet */
 	/* Hook up test interrupt handler just for this test */
 	if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED,
-			 netdev->name, netdev)) {
- 		shared_int = FALSE;
- 	} else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
-			      netdev->name, netdev)){
+			 netdev->name, netdev))
+		shared_int = FALSE;
+	else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
+			      netdev->name, netdev)) {
 		*data = 1;
 		return -1;
 	}
-	DPRINTK(PROBE,INFO, "testing %s interrupt\n",
+	DPRINTK(HW, INFO, "testing %s interrupt\n",
 	        (shared_int ? "shared" : "unshared"));
 
 	/* Disable all the interrupts */
@@ -1269,11 +1269,10 @@ e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x9140);
 		/* autoneg off */
 		e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8140);
-	} else if (adapter->hw.phy_type == e1000_phy_gg82563) {
+	} else if (adapter->hw.phy_type == e1000_phy_gg82563)
 		e1000_write_phy_reg(&adapter->hw,
 		                    GG82563_PHY_KMRN_MODE_CTRL,
 		                    0x1CC);
-	}
 
 	ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL);
 
@@ -1301,9 +1300,9 @@ e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 	}
 
 	if (adapter->hw.media_type == e1000_media_type_copper &&
-	   adapter->hw.phy_type == e1000_phy_m88) {
+	   adapter->hw.phy_type == e1000_phy_m88)
 		ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
-	} else {
+	else {
 		/* Set the ILOS bit on the fiber Nic is half
 		 * duplex link is detected. */
 		stat_reg = E1000_READ_REG(&adapter->hw, STATUS);
@@ -1439,11 +1438,10 @@ e1000_loopback_cleanup(struct e1000_adapter *adapter)
 	case e1000_82546_rev_3:
 	default:
 		hw->autoneg = TRUE;
-		if (hw->phy_type == e1000_phy_gg82563) {
+		if (hw->phy_type == e1000_phy_gg82563)
 			e1000_write_phy_reg(hw,
 					    GG82563_PHY_KMRN_MODE_CTRL,
 					    0x180);
-		}
 		e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
 		if (phy_reg & MII_CR_LOOPBACK) {
 			phy_reg &= ~MII_CR_LOOPBACK;
@@ -1677,14 +1675,12 @@ e1000_diag_test(struct net_device *netdev,
 	msleep_interruptible(4 * 1000);
 }
 
-static void
-e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+static int e1000_wol_exclusion(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
 {
-	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	int retval = 1; /* fail by default */
 
-	switch (adapter->hw.device_id) {
-	case E1000_DEV_ID_82542:
+	switch (hw->device_id) {
 	case E1000_DEV_ID_82543GC_FIBER:
 	case E1000_DEV_ID_82543GC_COPPER:
 	case E1000_DEV_ID_82544EI_FIBER:
@@ -1692,52 +1688,87 @@ e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 	case E1000_DEV_ID_82545EM_FIBER:
 	case E1000_DEV_ID_82545EM_COPPER:
 	case E1000_DEV_ID_82546GB_QUAD_COPPER:
+	case E1000_DEV_ID_82546GB_PCIE:
+		/* these don't support WoL at all */
 		wol->supported = 0;
-		wol->wolopts   = 0;
-		return;
-
-	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
-		/* device id 10B5 port-A supports wol */
-		if (!adapter->ksp3_port_a) {
-			wol->supported = 0;
-			return;
-		}
-		/* KSP3 does not suppport UCAST wake-ups for any interface */
-		wol->supported = WAKE_MCAST | WAKE_BCAST | WAKE_MAGIC;
-
-		if (adapter->wol & E1000_WUFC_EX)
-			DPRINTK(DRV, ERR, "Interface does not support "
-		        "directed (unicast) frame wake-up packets\n");
-		wol->wolopts = 0;
-		goto do_defaults;
-
+		break;
 	case E1000_DEV_ID_82546EB_FIBER:
 	case E1000_DEV_ID_82546GB_FIBER:
 	case E1000_DEV_ID_82571EB_FIBER:
-		/* Wake events only supported on port A for dual fiber */
+	case E1000_DEV_ID_82571EB_SERDES:
+	case E1000_DEV_ID_82571EB_COPPER:
+		/* Wake events not supported on port B */
 		if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) {
 			wol->supported = 0;
-			wol->wolopts   = 0;
-			return;
+			break;
 		}
-		/* Fall Through */
-
+		/* return success for non excluded adapter ports */
+		retval = 0;
+		break;
+	case E1000_DEV_ID_82571EB_QUAD_COPPER:
+	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+		/* quad port adapters only support WoL on port A */
+		if (!adapter->quad_port_a) {
+			wol->supported = 0;
+			break;
+		}
+		/* return success for non excluded adapter ports */
+		retval = 0;
+		break;
 	default:
-		wol->supported = WAKE_UCAST | WAKE_MCAST |
-				 WAKE_BCAST | WAKE_MAGIC;
-		wol->wolopts = 0;
+		/* dual port cards only support WoL on port A from now on
+		 * unless it was enabled in the eeprom for port B
+		 * so exclude FUNC_1 ports from having WoL enabled */
+		if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1 &&
+		    !adapter->eeprom_wol) {
+			wol->supported = 0;
+			break;
+		}
 
-do_defaults:
-		if (adapter->wol & E1000_WUFC_EX)
-			wol->wolopts |= WAKE_UCAST;
-		if (adapter->wol & E1000_WUFC_MC)
-			wol->wolopts |= WAKE_MCAST;
-		if (adapter->wol & E1000_WUFC_BC)
-			wol->wolopts |= WAKE_BCAST;
-		if (adapter->wol & E1000_WUFC_MAG)
-			wol->wolopts |= WAKE_MAGIC;
+		retval = 0;
+	}
+
+	return retval;
+}
+
+static void
+e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+
+	wol->supported = WAKE_UCAST | WAKE_MCAST |
+	                 WAKE_BCAST | WAKE_MAGIC;
+	wol->wolopts = 0;
+
+	/* this function will set ->supported = 0 and return 1 if wol is not
+	 * supported by this hardware */
+	if (e1000_wol_exclusion(adapter, wol))
 		return;
+
+	/* apply any specific unsupported masks here */
+	switch (adapter->hw.device_id) {
+	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+		/* KSP3 does not suppport UCAST wake-ups */
+		wol->supported &= ~WAKE_UCAST;
+
+		if (adapter->wol & E1000_WUFC_EX)
+			DPRINTK(DRV, ERR, "Interface does not support "
+		        "directed (unicast) frame wake-up packets\n");
+		break;
+	default:
+		break;
 	}
+
+	if (adapter->wol & E1000_WUFC_EX)
+		wol->wolopts |= WAKE_UCAST;
+	if (adapter->wol & E1000_WUFC_MC)
+		wol->wolopts |= WAKE_MCAST;
+	if (adapter->wol & E1000_WUFC_BC)
+		wol->wolopts |= WAKE_BCAST;
+	if (adapter->wol & E1000_WUFC_MAG)
+		wol->wolopts |= WAKE_MAGIC;
+
+	return;
 }
 
 static int
@@ -1746,51 +1777,35 @@ e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
 
-	switch (adapter->hw.device_id) {
-	case E1000_DEV_ID_82542:
-	case E1000_DEV_ID_82543GC_FIBER:
-	case E1000_DEV_ID_82543GC_COPPER:
-	case E1000_DEV_ID_82544EI_FIBER:
-	case E1000_DEV_ID_82546EB_QUAD_COPPER:
-	case E1000_DEV_ID_82546GB_QUAD_COPPER:
-	case E1000_DEV_ID_82545EM_FIBER:
-	case E1000_DEV_ID_82545EM_COPPER:
+	if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
+		return -EOPNOTSUPP;
+
+	if (e1000_wol_exclusion(adapter, wol))
 		return wol->wolopts ? -EOPNOTSUPP : 0;
 
+	switch (hw->device_id) {
 	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
-		/* device id 10B5 port-A supports wol */
-		if (!adapter->ksp3_port_a)
-			return wol->wolopts ? -EOPNOTSUPP : 0;
-
 		if (wol->wolopts & WAKE_UCAST) {
 			DPRINTK(DRV, ERR, "Interface does not support "
 		        "directed (unicast) frame wake-up packets\n");
 			return -EOPNOTSUPP;
 		}
-
-	case E1000_DEV_ID_82546EB_FIBER:
-	case E1000_DEV_ID_82546GB_FIBER:
-	case E1000_DEV_ID_82571EB_FIBER:
-		/* Wake events only supported on port A for dual fiber */
-		if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
-			return wol->wolopts ? -EOPNOTSUPP : 0;
-		/* Fall Through */
-
+		break;
 	default:
-		if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
-			return -EOPNOTSUPP;
+		break;
+	}
 
-		adapter->wol = 0;
+	/* these settings will always override what we currently have */
+	adapter->wol = 0;
 
-		if (wol->wolopts & WAKE_UCAST)
-			adapter->wol |= E1000_WUFC_EX;
-		if (wol->wolopts & WAKE_MCAST)
-			adapter->wol |= E1000_WUFC_MC;
-		if (wol->wolopts & WAKE_BCAST)
-			adapter->wol |= E1000_WUFC_BC;
-		if (wol->wolopts & WAKE_MAGIC)
-			adapter->wol |= E1000_WUFC_MAG;
-	}
+	if (wol->wolopts & WAKE_UCAST)
+		adapter->wol |= E1000_WUFC_EX;
+	if (wol->wolopts & WAKE_MCAST)
+		adapter->wol |= E1000_WUFC_MC;
+	if (wol->wolopts & WAKE_BCAST)
+		adapter->wol |= E1000_WUFC_BC;
+	if (wol->wolopts & WAKE_MAGIC)
+		adapter->wol |= E1000_WUFC_MAG;
 
 	return 0;
 }
@@ -1915,8 +1930,8 @@ static struct ethtool_ops e1000_ethtool_ops = {
 	.get_regs               = e1000_get_regs,
 	.get_wol                = e1000_get_wol,
 	.set_wol                = e1000_set_wol,
-	.get_msglevel	        = e1000_get_msglevel,
-	.set_msglevel	        = e1000_set_msglevel,
+	.get_msglevel           = e1000_get_msglevel,
+	.set_msglevel           = e1000_set_msglevel,
 	.nway_reset             = e1000_nway_reset,
 	.get_link               = ethtool_op_get_link,
 	.get_eeprom_len         = e1000_get_eeprom_len,
@@ -1924,17 +1939,17 @@ static struct ethtool_ops e1000_ethtool_ops = {
 	.set_eeprom             = e1000_set_eeprom,
 	.get_ringparam          = e1000_get_ringparam,
 	.set_ringparam          = e1000_set_ringparam,
-	.get_pauseparam		= e1000_get_pauseparam,
-	.set_pauseparam		= e1000_set_pauseparam,
-	.get_rx_csum		= e1000_get_rx_csum,
-	.set_rx_csum		= e1000_set_rx_csum,
-	.get_tx_csum		= e1000_get_tx_csum,
-	.set_tx_csum		= e1000_set_tx_csum,
-	.get_sg			= ethtool_op_get_sg,
-	.set_sg			= ethtool_op_set_sg,
+	.get_pauseparam         = e1000_get_pauseparam,
+	.set_pauseparam         = e1000_set_pauseparam,
+	.get_rx_csum            = e1000_get_rx_csum,
+	.set_rx_csum            = e1000_set_rx_csum,
+	.get_tx_csum            = e1000_get_tx_csum,
+	.set_tx_csum            = e1000_set_tx_csum,
+	.get_sg                 = ethtool_op_get_sg,
+	.set_sg                 = ethtool_op_set_sg,
 #ifdef NETIF_F_TSO
-	.get_tso		= ethtool_op_get_tso,
-	.set_tso		= e1000_set_tso,
+	.get_tso                = ethtool_op_get_tso,
+	.set_tso                = e1000_set_tso,
 #endif
 	.self_test_count        = e1000_diag_test_count,
 	.self_test              = e1000_diag_test,
@@ -1942,7 +1957,7 @@ static struct ethtool_ops e1000_ethtool_ops = {
 	.phys_id                = e1000_phys_id,
 	.get_stats_count        = e1000_get_stats_count,
 	.get_ethtool_stats      = e1000_get_ethtool_stats,
-	.get_perm_addr		= ethtool_op_get_perm_addr,
+	.get_perm_addr          = ethtool_op_get_perm_addr,
 };
 
 void e1000_set_ethtool_ops(struct net_device *netdev)

drivers/net/e1000/e1000_hw.h

@@ -336,9 +336,9 @@ uint32_t e1000_enable_mng_pass_thru(struct e1000_hw *hw);
 #define E1000_HI_MAX_MNG_DATA_LENGTH    0x6F8   /* Host Interface data length */
 
 #define E1000_MNG_DHCP_COMMAND_TIMEOUT  10      /* Time in ms to process MNG command */
-#define E1000_MNG_DHCP_COOKIE_OFFSET	0x6F0   /* Cookie offset */
-#define E1000_MNG_DHCP_COOKIE_LENGTH	0x10    /* Cookie length */
-#define E1000_MNG_IAMT_MODE		0x3
+#define E1000_MNG_DHCP_COOKIE_OFFSET    0x6F0   /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH    0x10    /* Cookie length */
+#define E1000_MNG_IAMT_MODE             0x3
 #define E1000_MNG_ICH_IAMT_MODE         0x2
 #define E1000_IAMT_SIGNATURE            0x544D4149 /* Intel(R) Active Management Technology signature */
 
@@ -385,7 +385,7 @@ struct e1000_host_mng_dhcp_cookie{
 #endif
 
 int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer,
-							uint16_t length);
+                                  uint16_t length);
 boolean_t e1000_check_mng_mode(struct e1000_hw *hw);
 boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
 
@@ -470,6 +470,7 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
 #define E1000_DEV_ID_82571EB_COPPER      0x105E
 #define E1000_DEV_ID_82571EB_FIBER       0x105F
 #define E1000_DEV_ID_82571EB_SERDES      0x1060
+#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
 #define E1000_DEV_ID_82572EI_COPPER      0x107D
 #define E1000_DEV_ID_82572EI_FIBER       0x107E
 #define E1000_DEV_ID_82572EI_SERDES      0x107F
@@ -523,7 +524,7 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);
 
 
 /* 802.1q VLAN Packet Sizes */
-#define VLAN_TAG_SIZE                     4     /* 802.3ac tag (not DMAed) */
+#define VLAN_TAG_SIZE  4     /* 802.3ac tag (not DMAed) */
 
 /* Ethertype field values */
 #define ETHERNET_IEEE_VLAN_TYPE 0x8100  /* 802.3ac packet */
@@ -697,6 +698,7 @@ union e1000_rx_desc_packet_split {
     E1000_RXDEXT_STATERR_CXE |            \
     E1000_RXDEXT_STATERR_RXE)
 
+
 /* Transmit Descriptor */
 struct e1000_tx_desc {
     uint64_t buffer_addr;       /* Address of the descriptor's data buffer */
@@ -2086,7 +2088,7 @@ struct e1000_hw {
 #define E1000_MANC_EN_IP_ADDR_FILTER    0x00400000 /* Enable IP address
                                                     * filtering */
 #define E1000_MANC_EN_XSUM_FILTER   0x00800000 /* Enable checksum filtering */
-#define E1000_MANC_BR_EN            0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_BR_EN         0x01000000 /* Enable broadcast filtering */
 #define E1000_MANC_SMB_REQ       0x01000000 /* SMBus Request */
 #define E1000_MANC_SMB_GNT       0x02000000 /* SMBus Grant */
 #define E1000_MANC_SMB_CLK_IN    0x04000000 /* SMBus Clock In */
@@ -2172,7 +2174,7 @@ struct e1000_host_command_info {
 
 #define E1000_MDALIGN          4096
 
-/* PCI-Ex registers */
+/* PCI-Ex registers*/
 
 /* PCI-Ex Control Register */
 #define E1000_GCR_RXD_NO_SNOOP          0x00000001
@@ -2224,7 +2226,7 @@ struct e1000_host_command_info {
 #define EEPROM_EWDS_OPCODE_MICROWIRE  0x10 /* EEPROM erast/write disable */
 
 /* EEPROM Commands - SPI */
-#define EEPROM_MAX_RETRY_SPI    5000 /* Max wait of 5ms, for RDY signal */
+#define EEPROM_MAX_RETRY_SPI        5000 /* Max wait of 5ms, for RDY signal */
 #define EEPROM_READ_OPCODE_SPI      0x03  /* EEPROM read opcode */
 #define EEPROM_WRITE_OPCODE_SPI     0x02  /* EEPROM write opcode */
 #define EEPROM_A8_OPCODE_SPI        0x08  /* opcode bit-3 = address bit-8 */
@@ -3082,10 +3084,10 @@ struct e1000_host_command_info {
 
 /* DSP Distance Register (Page 5, Register 26) */
 #define GG82563_DSPD_CABLE_LENGTH               0x0007 /* 0 = <50M;
-							      1 = 50-80M;
-							      2 = 80-110M;
-							      3 = 110-140M;
-							      4 = >140M */
+                                                          1 = 50-80M;
+                                                          2 = 80-110M;
+                                                          3 = 110-140M;
+                                                          4 = >140M */
 
 /* Kumeran Mode Control Register (Page 193, Register 16) */
 #define GG82563_KMCR_PHY_LEDS_EN                    0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */

drivers/net/e1000/e1000_main.c

@@ -36,7 +36,7 @@ static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
 #else
 #define DRIVERNAPI "-NAPI"
 #endif
-#define DRV_VERSION "7.1.9-k6"DRIVERNAPI
+#define DRV_VERSION "7.2.7-k2"DRIVERNAPI
 char e1000_driver_version[] = DRV_VERSION;
 static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
 
@@ -98,6 +98,7 @@ static struct pci_device_id e1000_pci_tbl[] = {
 	INTEL_E1000_ETHERNET_DEVICE(0x1098),
 	INTEL_E1000_ETHERNET_DEVICE(0x1099),
 	INTEL_E1000_ETHERNET_DEVICE(0x109A),
+	INTEL_E1000_ETHERNET_DEVICE(0x10A4),
 	INTEL_E1000_ETHERNET_DEVICE(0x10B5),
 	INTEL_E1000_ETHERNET_DEVICE(0x10B9),
 	INTEL_E1000_ETHERNET_DEVICE(0x10BA),
@@ -681,9 +682,9 @@ e1000_probe(struct pci_dev *pdev,
 	unsigned long flash_start, flash_len;
 
 	static int cards_found = 0;
-	static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */
+	static int global_quad_port_a = 0; /* global ksp3 port a indication */
 	int i, err, pci_using_dac;
-	uint16_t eeprom_data;
+	uint16_t eeprom_data = 0;
 	uint16_t eeprom_apme_mask = E1000_EEPROM_APME;
 	if ((err = pci_enable_device(pdev)))
 		return err;
@@ -695,21 +696,20 @@ e1000_probe(struct pci_dev *pdev,
 		if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
 		    (err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
 			E1000_ERR("No usable DMA configuration, aborting\n");
-			return err;
+			goto err_dma;
 		}
 		pci_using_dac = 0;
 	}
 
 	if ((err = pci_request_regions(pdev, e1000_driver_name)))
-		return err;
+		goto err_pci_reg;
 
 	pci_set_master(pdev);
 
+	err = -ENOMEM;
 	netdev = alloc_etherdev(sizeof(struct e1000_adapter));
-	if (!netdev) {
-		err = -ENOMEM;
+	if (!netdev)
 		goto err_alloc_etherdev;
-	}
 
 	SET_MODULE_OWNER(netdev);
 	SET_NETDEV_DEV(netdev, &pdev->dev);
@@ -724,11 +724,10 @@ e1000_probe(struct pci_dev *pdev,
 	mmio_start = pci_resource_start(pdev, BAR_0);
 	mmio_len = pci_resource_len(pdev, BAR_0);
 
+	err = -EIO;
 	adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
-	if (!adapter->hw.hw_addr) {
-		err = -EIO;
+	if (!adapter->hw.hw_addr)
 		goto err_ioremap;
-	}
 
 	for (i = BAR_1; i <= BAR_5; i++) {
 		if (pci_resource_len(pdev, i) == 0)
@@ -773,6 +772,7 @@ e1000_probe(struct pci_dev *pdev,
 	if ((err = e1000_sw_init(adapter)))
 		goto err_sw_init;
 
+	err = -EIO;
 	/* Flash BAR mapping must happen after e1000_sw_init
 	 * because it depends on mac_type */
 	if ((adapter->hw.mac_type == e1000_ich8lan) &&
@@ -780,24 +780,13 @@ e1000_probe(struct pci_dev *pdev,
 		flash_start = pci_resource_start(pdev, 1);
 		flash_len = pci_resource_len(pdev, 1);
 		adapter->hw.flash_address = ioremap(flash_start, flash_len);
-		if (!adapter->hw.flash_address) {
-			err = -EIO;
+		if (!adapter->hw.flash_address)
 			goto err_flashmap;
-		}
 	}
 
-	if ((err = e1000_check_phy_reset_block(&adapter->hw)))
+	if (e1000_check_phy_reset_block(&adapter->hw))
 		DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
 
-	/* if ksp3, indicate if it's port a being setup */
-	if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
-			e1000_ksp3_port_a == 0)
-		adapter->ksp3_port_a = 1;
-	e1000_ksp3_port_a++;
-	/* Reset for multiple KP3 adapters */
-	if (e1000_ksp3_port_a == 4)
-		e1000_ksp3_port_a = 0;
-
 	if (adapter->hw.mac_type >= e1000_82543) {
 		netdev->features = NETIF_F_SG |
 				   NETIF_F_HW_CSUM |
@@ -829,7 +818,7 @@ e1000_probe(struct pci_dev *pdev,
 
 	if (e1000_init_eeprom_params(&adapter->hw)) {
 		E1000_ERR("EEPROM initialization failed\n");
-		return -EIO;
+		goto err_eeprom;
 	}
 
 	/* before reading the EEPROM, reset the controller to
@@ -841,7 +830,6 @@ e1000_probe(struct pci_dev *pdev,
 
 	if (e1000_validate_eeprom_checksum(&adapter->hw) < 0) {
 		DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
-		err = -EIO;
 		goto err_eeprom;
 	}
 
@@ -854,12 +842,9 @@ e1000_probe(struct pci_dev *pdev,
 
 	if (!is_valid_ether_addr(netdev->perm_addr)) {
 		DPRINTK(PROBE, ERR, "Invalid MAC Address\n");
-		err = -EIO;
 		goto err_eeprom;
 	}
 
-	e1000_read_part_num(&adapter->hw, &(adapter->part_num));
-
 	e1000_get_bus_info(&adapter->hw);
 
 	init_timer(&adapter->tx_fifo_stall_timer);
@@ -920,7 +905,38 @@ e1000_probe(struct pci_dev *pdev,
 		break;
 	}
 	if (eeprom_data & eeprom_apme_mask)
-		adapter->wol |= E1000_WUFC_MAG;
+		adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+	/* now that we have the eeprom settings, apply the special cases
+	 * where the eeprom may be wrong or the board simply won't support
+	 * wake on lan on a particular port */
+	switch (pdev->device) {
+	case E1000_DEV_ID_82546GB_PCIE:
+		adapter->eeprom_wol = 0;
+		break;
+	case E1000_DEV_ID_82546EB_FIBER:
+	case E1000_DEV_ID_82546GB_FIBER:
+	case E1000_DEV_ID_82571EB_FIBER:
+		/* Wake events only supported on port A for dual fiber
+		 * regardless of eeprom setting */
+		if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1)
+			adapter->eeprom_wol = 0;
+		break;
+	case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+	case E1000_DEV_ID_82571EB_QUAD_COPPER:
+		/* if quad port adapter, disable WoL on all but port A */
+		if (global_quad_port_a != 0)
+			adapter->eeprom_wol = 0;
+		else
+			adapter->quad_port_a = 1;
+		/* Reset for multiple quad port adapters */
+		if (++global_quad_port_a == 4)
+			global_quad_port_a = 0;
+		break;
+	}
+
+	/* initialize the wol settings based on the eeprom settings */
+	adapter->wol = adapter->eeprom_wol;
 
 	/* print bus type/speed/width info */
 	{
@@ -963,16 +979,33 @@ e1000_probe(struct pci_dev *pdev,
 	return 0;
 
 err_register:
+	e1000_release_hw_control(adapter);
+err_eeprom:
+	if (!e1000_check_phy_reset_block(&adapter->hw))
+		e1000_phy_hw_reset(&adapter->hw);
+
 	if (adapter->hw.flash_address)
 		iounmap(adapter->hw.flash_address);
 err_flashmap:
+#ifdef CONFIG_E1000_NAPI
+	for (i = 0; i < adapter->num_rx_queues; i++)
+		dev_put(&adapter->polling_netdev[i]);
+#endif
+
+	kfree(adapter->tx_ring);
+	kfree(adapter->rx_ring);
+#ifdef CONFIG_E1000_NAPI
+	kfree(adapter->polling_netdev);
+#endif
 err_sw_init:
-err_eeprom:
 	iounmap(adapter->hw.hw_addr);
 err_ioremap:
 	free_netdev(netdev);
 err_alloc_etherdev:
 	pci_release_regions(pdev);
+err_pci_reg:
+err_dma:
+	pci_disable_device(pdev);
 	return err;
 }
 
@@ -1207,7 +1240,7 @@ e1000_open(struct net_device *netdev)
 
 	err = e1000_request_irq(adapter);
 	if (err)
-		goto err_up;
+		goto err_req_irq;
 
 	e1000_power_up_phy(adapter);
 
@@ -1228,6 +1261,9 @@ e1000_open(struct net_device *netdev)
 	return E1000_SUCCESS;
 
 err_up:
+	e1000_power_down_phy(adapter);
+	e1000_free_irq(adapter);
+err_req_irq:
 	e1000_free_all_rx_resources(adapter);
 err_setup_rx:
 	e1000_free_all_tx_resources(adapter);
@@ -1380,10 +1416,6 @@ setup_tx_desc_die:
  * 				  (Descriptors) for all queues
  * @adapter: board private structure
  *
- * If this function returns with an error, then it's possible one or
- * more of the rings is populated (while the rest are not).  It is the
- * callers duty to clean those orphaned rings.
- *
  * Return 0 on success, negative on failure
  **/
 
@@ -1397,6 +1429,9 @@ e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
 		if (err) {
 			DPRINTK(PROBE, ERR,
 				"Allocation for Tx Queue %u failed\n", i);
+			for (i-- ; i >= 0; i--)
+				e1000_free_tx_resources(adapter,
+							&adapter->tx_ring[i]);
 			break;
 		}
 	}
@@ -1636,10 +1671,6 @@ setup_rx_desc_die:
  * 				  (Descriptors) for all queues
  * @adapter: board private structure
  *
- * If this function returns with an error, then it's possible one or
- * more of the rings is populated (while the rest are not).  It is the
- * callers duty to clean those orphaned rings.
- *
  * Return 0 on success, negative on failure
  **/
 
@@ -1653,6 +1684,9 @@ e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
 		if (err) {
 			DPRINTK(PROBE, ERR,
 				"Allocation for Rx Queue %u failed\n", i);
+			for (i-- ; i >= 0; i--)
+				e1000_free_rx_resources(adapter,
+							&adapter->rx_ring[i]);
 			break;
 		}
 	}
@@ -2439,10 +2473,9 @@ e1000_watchdog(unsigned long data)
 			 * disable receives in the ISR and
 			 * reset device here in the watchdog
 			 */
-			if (adapter->hw.mac_type == e1000_80003es2lan) {
+			if (adapter->hw.mac_type == e1000_80003es2lan)
 				/* reset device */
 				schedule_work(&adapter->reset_task);
-			}
 		}
 
 		e1000_smartspeed(adapter);
@@ -3677,7 +3710,7 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter,
 			E1000_DBG("%s: Receive packet consumed multiple"
 				  " buffers\n", netdev->name);
 			/* recycle */
-			buffer_info-> skb = skb;
+			buffer_info->skb = skb;
 			goto next_desc;
 		}
 
@@ -3708,7 +3741,6 @@ e1000_clean_rx_irq(struct e1000_adapter *adapter,
 			    netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
 			if (new_skb) {
 				skb_reserve(new_skb, NET_IP_ALIGN);
-				new_skb->dev = netdev;
 				memcpy(new_skb->data - NET_IP_ALIGN,
 				       skb->data - NET_IP_ALIGN,
 				       length + NET_IP_ALIGN);
@@ -3975,13 +4007,13 @@ e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
 	buffer_info = &rx_ring->buffer_info[i];
 
 	while (cleaned_count--) {
-		if (!(skb = buffer_info->skb))
-			skb = netdev_alloc_skb(netdev, bufsz);
-		else {
+		skb = buffer_info->skb;
+		if (skb) {
 			skb_trim(skb, 0);
 			goto map_skb;
 		}
 
+		skb = netdev_alloc_skb(netdev, bufsz);
 		if (unlikely(!skb)) {
 			/* Better luck next round */
 			adapter->alloc_rx_buff_failed++;
@@ -4006,10 +4038,10 @@ e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
 				dev_kfree_skb(skb);
 				dev_kfree_skb(oldskb);
 				break; /* while !buffer_info->skb */
-			} else {
-				/* Use new allocation */
-				dev_kfree_skb(oldskb);
 			}
+
+			/* Use new allocation */
+			dev_kfree_skb(oldskb);
 		}
 		/* Make buffer alignment 2 beyond a 16 byte boundary
 		 * this will result in a 16 byte aligned IP header after
@@ -4017,8 +4049,6 @@ e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
 		 */
 		skb_reserve(skb, NET_IP_ALIGN);
 
-		skb->dev = netdev;
-
 		buffer_info->skb = skb;
 		buffer_info->length = adapter->rx_buffer_len;
 map_skb:
@@ -4132,8 +4162,6 @@ e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
 		 */
 		skb_reserve(skb, NET_IP_ALIGN);
 
-		skb->dev = netdev;
-
 		buffer_info->skb = skb;
 		buffer_info->length = adapter->rx_ps_bsize0;
 		buffer_info->dma = pci_map_single(pdev, skb->data,
@@ -4625,7 +4653,7 @@ e1000_suspend(struct pci_dev *pdev, pm_message_t state)
 		e1000_set_multi(netdev);
 
 		/* turn on all-multi mode if wake on multicast is enabled */
-		if (adapter->wol & E1000_WUFC_MC) {
+		if (wufc & E1000_WUFC_MC) {
 			rctl = E1000_READ_REG(&adapter->hw, RCTL);
 			rctl |= E1000_RCTL_MPE;
 			E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
@@ -4697,11 +4725,14 @@ e1000_resume(struct pci_dev *pdev)
 {
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct e1000_adapter *adapter = netdev_priv(netdev);
-	uint32_t manc, ret_val;
+	uint32_t manc, err;
 
 	pci_set_power_state(pdev, PCI_D0);
 	e1000_pci_restore_state(adapter);
-	ret_val = pci_enable_device(pdev);
+	if ((err = pci_enable_device(pdev))) {
+		printk(KERN_ERR "e1000: Cannot enable PCI device from suspend\n");
+		return err;
+	}
 	pci_set_master(pdev);
 
 	pci_enable_wake(pdev, PCI_D3hot, 0);

drivers/net/e1000/e1000_param.c

@@ -324,7 +324,6 @@ e1000_check_options(struct e1000_adapter *adapter)
 		DPRINTK(PROBE, NOTICE,
 		       "Warning: no configuration for board #%i\n", bd);
 		DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
-		bd = E1000_MAX_NIC;
 	}
 
 	{ /* Transmit Descriptor Count */
@@ -342,9 +341,14 @@ e1000_check_options(struct e1000_adapter *adapter)
 		opt.arg.r.max = mac_type < e1000_82544 ?
 			E1000_MAX_TXD : E1000_MAX_82544_TXD;
 
-		tx_ring->count = TxDescriptors[bd];
-		e1000_validate_option(&tx_ring->count, &opt, adapter);
-		E1000_ROUNDUP(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE);
+		if (num_TxDescriptors > bd) {
+			tx_ring->count = TxDescriptors[bd];
+			e1000_validate_option(&tx_ring->count, &opt, adapter);
+			E1000_ROUNDUP(tx_ring->count,
+						REQ_TX_DESCRIPTOR_MULTIPLE);
+		} else {
+			tx_ring->count = opt.def;
+		}
 		for (i = 0; i < adapter->num_tx_queues; i++)
 			tx_ring[i].count = tx_ring->count;
 	}
@@ -363,9 +367,14 @@ e1000_check_options(struct e1000_adapter *adapter)
 		opt.arg.r.max = mac_type < e1000_82544 ? E1000_MAX_RXD :
 			E1000_MAX_82544_RXD;
 
-		rx_ring->count = RxDescriptors[bd];
-		e1000_validate_option(&rx_ring->count, &opt, adapter);
-		E1000_ROUNDUP(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE);
+		if (num_RxDescriptors > bd) {
+			rx_ring->count = RxDescriptors[bd];
+			e1000_validate_option(&rx_ring->count, &opt, adapter);
+			E1000_ROUNDUP(rx_ring->count,
+						REQ_RX_DESCRIPTOR_MULTIPLE);
+		} else {
+			rx_ring->count = opt.def;
+		}
 		for (i = 0; i < adapter->num_rx_queues; i++)
 			rx_ring[i].count = rx_ring->count;
 	}
@@ -377,9 +386,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 			.def  = OPTION_ENABLED
 		};
 
-		int rx_csum = XsumRX[bd];
-		e1000_validate_option(&rx_csum, &opt, adapter);
-		adapter->rx_csum = rx_csum;
+		if (num_XsumRX > bd) {
+			int rx_csum = XsumRX[bd];
+			e1000_validate_option(&rx_csum, &opt, adapter);
+			adapter->rx_csum = rx_csum;
+		} else {
+			adapter->rx_csum = opt.def;
+		}
 	}
 	{ /* Flow Control */
 
@@ -399,9 +412,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .p = fc_list }}
 		};
 
-		int fc = FlowControl[bd];
-		e1000_validate_option(&fc, &opt, adapter);
-		adapter->hw.fc = adapter->hw.original_fc = fc;
+		if (num_FlowControl > bd) {
+			int fc = FlowControl[bd];
+			e1000_validate_option(&fc, &opt, adapter);
+			adapter->hw.fc = adapter->hw.original_fc = fc;
+		} else {
+			adapter->hw.fc = adapter->hw.original_fc = opt.def;
+		}
 	}
 	{ /* Transmit Interrupt Delay */
 		struct e1000_option opt = {
@@ -413,8 +430,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .max = MAX_TXDELAY }}
 		};
 
-		adapter->tx_int_delay = TxIntDelay[bd];
-		e1000_validate_option(&adapter->tx_int_delay, &opt, adapter);
+		if (num_TxIntDelay > bd) {
+			adapter->tx_int_delay = TxIntDelay[bd];
+			e1000_validate_option(&adapter->tx_int_delay, &opt,
+			                      adapter);
+		} else {
+			adapter->tx_int_delay = opt.def;
+		}
 	}
 	{ /* Transmit Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -426,9 +448,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .max = MAX_TXABSDELAY }}
 		};
 
-		adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
-		e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
-		                      adapter);
+		if (num_TxAbsIntDelay > bd) {
+			adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+			e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+			                      adapter);
+		} else {
+			adapter->tx_abs_int_delay = opt.def;
+		}
 	}
 	{ /* Receive Interrupt Delay */
 		struct e1000_option opt = {
@@ -440,8 +466,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .max = MAX_RXDELAY }}
 		};
 
-		adapter->rx_int_delay = RxIntDelay[bd];
-		e1000_validate_option(&adapter->rx_int_delay, &opt, adapter);
+		if (num_RxIntDelay > bd) {
+			adapter->rx_int_delay = RxIntDelay[bd];
+			e1000_validate_option(&adapter->rx_int_delay, &opt,
+			                      adapter);
+		} else {
+			adapter->rx_int_delay = opt.def;
+		}
 	}
 	{ /* Receive Absolute Interrupt Delay */
 		struct e1000_option opt = {
@@ -453,9 +484,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .max = MAX_RXABSDELAY }}
 		};
 
-		adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
-		e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
-		                      adapter);
+		if (num_RxAbsIntDelay > bd) {
+			adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+			e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+			                      adapter);
+		} else {
+			adapter->rx_abs_int_delay = opt.def;
+		}
 	}
 	{ /* Interrupt Throttling Rate */
 		struct e1000_option opt = {
@@ -467,18 +502,24 @@ e1000_check_options(struct e1000_adapter *adapter)
 					 .max = MAX_ITR }}
 		};
 
-		adapter->itr = InterruptThrottleRate[bd];
-		switch (adapter->itr) {
-		case 0:
-			DPRINTK(PROBE, INFO, "%s turned off\n", opt.name);
-			break;
-		case 1:
-			DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
-				opt.name);
-			break;
-		default:
-			e1000_validate_option(&adapter->itr, &opt, adapter);
-			break;
+		if (num_InterruptThrottleRate > bd) {
+			adapter->itr = InterruptThrottleRate[bd];
+			switch (adapter->itr) {
+			case 0:
+				DPRINTK(PROBE, INFO, "%s turned off\n",
+				        opt.name);
+				break;
+			case 1:
+				DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
+				        opt.name);
+				break;
+			default:
+				e1000_validate_option(&adapter->itr, &opt,
+				                      adapter);
+				break;
+			}
+		} else {
+			adapter->itr = opt.def;
 		}
 	}
 	{ /* Smart Power Down */
@@ -489,9 +530,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 			.def  = OPTION_DISABLED
 		};
 
-		int spd = SmartPowerDownEnable[bd];
-		e1000_validate_option(&spd, &opt, adapter);
-		adapter->smart_power_down = spd;
+		if (num_SmartPowerDownEnable > bd) {
+			int spd = SmartPowerDownEnable[bd];
+			e1000_validate_option(&spd, &opt, adapter);
+			adapter->smart_power_down = spd;
+		} else {
+			adapter->smart_power_down = opt.def;
+		}
 	}
 	{ /* Kumeran Lock Loss Workaround */
 		struct e1000_option opt = {
@@ -501,9 +546,13 @@ e1000_check_options(struct e1000_adapter *adapter)
 			.def  = OPTION_ENABLED
 		};
 
+		if (num_KumeranLockLoss > bd) {
 			int kmrn_lock_loss = KumeranLockLoss[bd];
 			e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
 			adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss;
+		} else {
+			adapter->hw.kmrn_lock_loss_workaround_disabled = !opt.def;
+		}
 	}
 
 	switch (adapter->hw.media_type) {
@@ -530,18 +579,17 @@ static void __devinit
 e1000_check_fiber_options(struct e1000_adapter *adapter)
 {
 	int bd = adapter->bd_number;
-	bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
-	if ((Speed[bd] != OPTION_UNSET)) {
+	if (num_Speed > bd) {
 		DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 
-	if ((Duplex[bd] != OPTION_UNSET)) {
+	if (num_Duplex > bd) {
 		DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
 		       "parameter ignored\n");
 	}
 
-	if ((AutoNeg[bd] != OPTION_UNSET) && (AutoNeg[bd] != 0x20)) {
+	if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) {
 		DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is "
 				 "not valid for fiber adapters, "
 				 "parameter ignored\n");
@@ -560,7 +608,6 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 {
 	int speed, dplx, an;
 	int bd = adapter->bd_number;
-	bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
 
 	{ /* Speed */
 		struct e1000_opt_list speed_list[] = {{          0, "" },
@@ -577,8 +624,12 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 					 .p = speed_list }}
 		};
 
-		speed = Speed[bd];
-		e1000_validate_option(&speed, &opt, adapter);
+		if (num_Speed > bd) {
+			speed = Speed[bd];
+			e1000_validate_option(&speed, &opt, adapter);
+		} else {
+			speed = opt.def;
+		}
 	}
 	{ /* Duplex */
 		struct e1000_opt_list dplx_list[] = {{           0, "" },
@@ -600,11 +651,15 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 			        "Speed/Duplex/AutoNeg parameter ignored.\n");
 			return;
 		}
-		dplx = Duplex[bd];
-		e1000_validate_option(&dplx, &opt, adapter);
+		if (num_Duplex > bd) {
+			dplx = Duplex[bd];
+			e1000_validate_option(&dplx, &opt, adapter);
+		} else {
+			dplx = opt.def;
+		}
 	}
 
-	if (AutoNeg[bd] != OPTION_UNSET && (speed != 0 || dplx != 0)) {
+	if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) {
 		DPRINTK(PROBE, INFO,
 		       "AutoNeg specified along with Speed or Duplex, "
 		       "parameter ignored\n");
@@ -653,15 +708,19 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
 					 .p = an_list }}
 		};
 
-		an = AutoNeg[bd];
-		e1000_validate_option(&an, &opt, adapter);
+		if (num_AutoNeg > bd) {
+			an = AutoNeg[bd];
+			e1000_validate_option(&an, &opt, adapter);
+		} else {
+			an = opt.def;
+		}
 		adapter->hw.autoneg_advertised = an;
 	}
 
 	switch (speed + dplx) {
 	case 0:
 		adapter->hw.autoneg = adapter->fc_autoneg = 1;
-		if (Speed[bd] != OPTION_UNSET || Duplex[bd] != OPTION_UNSET)
+		if ((num_Speed > bd) && (speed != 0 || dplx != 0))
 			DPRINTK(PROBE, INFO,
 			       "Speed and duplex autonegotiation enabled\n");
 		break;

drivers/net/ixgb/ixgb.h

@@ -110,9 +110,6 @@ struct ixgb_adapter;
 #define IXGB_RXBUFFER_8192  8192
 #define IXGB_RXBUFFER_16384 16384
 
-/* How many Tx Descriptors do we need to call netif_wake_queue? */
-#define IXGB_TX_QUEUE_WAKE 16
-
 /* How many Rx Buffers do we bundle into one write to the hardware ? */
 #define IXGB_RX_BUFFER_WRITE	4	/* Must be power of 2 */
 
@@ -173,7 +170,7 @@ struct ixgb_adapter {
 	unsigned long led_status;
 
 	/* TX */
-	struct ixgb_desc_ring tx_ring;
+	struct ixgb_desc_ring tx_ring ____cacheline_aligned_in_smp;
 	unsigned long timeo_start;
 	uint32_t tx_cmd_type;
 	uint64_t hw_csum_tx_good;

drivers/net/ixgb/ixgb_ethtool.c

@@ -654,11 +654,7 @@ ixgb_phys_id(struct net_device *netdev, uint32_t data)
 
 	mod_timer(&adapter->blink_timer, jiffies);
 
-	if (data)
-		schedule_timeout_interruptible(data * HZ);
-	else
-		schedule_timeout_interruptible(MAX_SCHEDULE_TIMEOUT);
-
+	msleep_interruptible(data * 1000);
 	del_timer_sync(&adapter->blink_timer);
 	ixgb_led_off(&adapter->hw);
 	clear_bit(IXGB_LED_ON, &adapter->led_status);

drivers/net/ixgb/ixgb_main.c

@@ -36,7 +36,7 @@ static char ixgb_driver_string[] = "Intel(R) PRO/10GbE Network Driver";
 #else
 #define DRIVERNAPI "-NAPI"
 #endif
-#define DRV_VERSION		"1.0.109-k4"DRIVERNAPI
+#define DRV_VERSION		"1.0.112-k2"DRIVERNAPI
 char ixgb_driver_version[] = DRV_VERSION;
 static char ixgb_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
 
@@ -118,15 +118,26 @@ static void ixgb_restore_vlan(struct ixgb_adapter *adapter);
 static void ixgb_netpoll(struct net_device *dev);
 #endif
 
-/* Exported from other modules */
+static pci_ers_result_t ixgb_io_error_detected (struct pci_dev *pdev,
+	                     enum pci_channel_state state);
+static pci_ers_result_t ixgb_io_slot_reset (struct pci_dev *pdev);
+static void ixgb_io_resume (struct pci_dev *pdev);
 
+/* Exported from other modules */
 extern void ixgb_check_options(struct ixgb_adapter *adapter);
 
+static struct pci_error_handlers ixgb_err_handler = {
+	.error_detected = ixgb_io_error_detected,
+	.slot_reset = ixgb_io_slot_reset,
+	.resume = ixgb_io_resume,
+};
+
 static struct pci_driver ixgb_driver = {
 	.name     = ixgb_driver_name,
 	.id_table = ixgb_pci_tbl,
 	.probe    = ixgb_probe,
 	.remove   = __devexit_p(ixgb_remove),
+	.err_handler = &ixgb_err_handler
 };
 
 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
@@ -1174,6 +1185,7 @@ ixgb_tso(struct ixgb_adapter *adapter, struct sk_buff *skb)
 	int err;
 
 	if (likely(skb_is_gso(skb))) {
+		struct ixgb_buffer *buffer_info;
 		if (skb_header_cloned(skb)) {
 			err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
 			if (err)
@@ -1196,6 +1208,8 @@ ixgb_tso(struct ixgb_adapter *adapter, struct sk_buff *skb)
 
 		i = adapter->tx_ring.next_to_use;
 		context_desc = IXGB_CONTEXT_DESC(adapter->tx_ring, i);
+		buffer_info = &adapter->tx_ring.buffer_info[i];
+		WARN_ON(buffer_info->dma != 0);
 
 		context_desc->ipcss = ipcss;
 		context_desc->ipcso = ipcso;
@@ -1233,11 +1247,14 @@ ixgb_tx_csum(struct ixgb_adapter *adapter, struct sk_buff *skb)
 	uint8_t css, cso;
 
 	if(likely(skb->ip_summed == CHECKSUM_HW)) {
+		struct ixgb_buffer *buffer_info;
 		css = skb->h.raw - skb->data;
 		cso = (skb->h.raw + skb->csum) - skb->data;
 
 		i = adapter->tx_ring.next_to_use;
 		context_desc = IXGB_CONTEXT_DESC(adapter->tx_ring, i);
+		buffer_info = &adapter->tx_ring.buffer_info[i];
+		WARN_ON(buffer_info->dma != 0);
 
 		context_desc->tucss = css;
 		context_desc->tucso = cso;
@@ -1283,6 +1300,7 @@ ixgb_tx_map(struct ixgb_adapter *adapter, struct sk_buff *skb,
 		buffer_info = &tx_ring->buffer_info[i];
 		size = min(len, IXGB_MAX_DATA_PER_TXD);
 		buffer_info->length = size;
+		WARN_ON(buffer_info->dma != 0);
 		buffer_info->dma =
 			pci_map_single(adapter->pdev,
 				skb->data + offset,
@@ -1543,6 +1561,11 @@ void
 ixgb_update_stats(struct ixgb_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
+	struct pci_dev *pdev = adapter->pdev;
+
+	/* Prevent stats update while adapter is being reset */
+	if (pdev->error_state && pdev->error_state != pci_channel_io_normal)
+		return;
 
 	if((netdev->flags & IFF_PROMISC) || (netdev->flags & IFF_ALLMULTI) ||
 	   (netdev->mc_count > IXGB_MAX_NUM_MULTICAST_ADDRESSES)) {
@@ -1787,7 +1810,7 @@ ixgb_clean_tx_irq(struct ixgb_adapter *adapter)
 	if (unlikely(netif_queue_stopped(netdev))) {
 		spin_lock(&adapter->tx_lock);
 		if (netif_queue_stopped(netdev) && netif_carrier_ok(netdev) &&
-		    (IXGB_DESC_UNUSED(tx_ring) > IXGB_TX_QUEUE_WAKE))
+		    (IXGB_DESC_UNUSED(tx_ring) >= DESC_NEEDED))
 			netif_wake_queue(netdev);
 		spin_unlock(&adapter->tx_lock);
 	}
@@ -1948,10 +1971,9 @@ ixgb_clean_rx_irq(struct ixgb_adapter *adapter)
 #define IXGB_CB_LENGTH 256
 		if (length < IXGB_CB_LENGTH) {
 			struct sk_buff *new_skb =
-			    dev_alloc_skb(length + NET_IP_ALIGN);
+			    netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
 			if (new_skb) {
 				skb_reserve(new_skb, NET_IP_ALIGN);
-				new_skb->dev = netdev;
 				memcpy(new_skb->data - NET_IP_ALIGN,
 				       skb->data - NET_IP_ALIGN,
 				       length + NET_IP_ALIGN);
@@ -2031,14 +2053,14 @@ ixgb_alloc_rx_buffers(struct ixgb_adapter *adapter)
 	/* leave three descriptors unused */
 	while(--cleancount > 2) {
 		/* recycle! its good for you */
-		if (!(skb = buffer_info->skb))
-			skb = dev_alloc_skb(adapter->rx_buffer_len
-			                    + NET_IP_ALIGN);
-		else {
+		skb = buffer_info->skb;
+		if (skb) {
 			skb_trim(skb, 0);
 			goto map_skb;
 		}
 
+		skb = netdev_alloc_skb(netdev, adapter->rx_buffer_len
+			               + NET_IP_ALIGN);
 		if (unlikely(!skb)) {
 			/* Better luck next round */
 			adapter->alloc_rx_buff_failed++;
@@ -2051,8 +2073,6 @@ ixgb_alloc_rx_buffers(struct ixgb_adapter *adapter)
 		 */
 		skb_reserve(skb, NET_IP_ALIGN);
 
-		skb->dev = netdev;
-
 		buffer_info->skb = skb;
 		buffer_info->length = adapter->rx_buffer_len;
 map_skb:
@@ -2190,7 +2210,7 @@ ixgb_restore_vlan(struct ixgb_adapter *adapter)
 
 static void ixgb_netpoll(struct net_device *dev)
 {
-	struct ixgb_adapter *adapter = dev->priv;
+	struct ixgb_adapter *adapter = netdev_priv(dev);
 
 	disable_irq(adapter->pdev->irq);
 	ixgb_intr(adapter->pdev->irq, dev, NULL);
@@ -2198,4 +2218,98 @@ static void ixgb_netpoll(struct net_device *dev)
 }
 #endif
 
+/**
+ * ixgb_io_error_detected() - called when PCI error is detected
+ * @pdev    pointer to pci device with error
+ * @state   pci channel state after error
+ *
+ * This callback is called by the PCI subsystem whenever
+ * a PCI bus error is detected.
+ */
+static pci_ers_result_t ixgb_io_error_detected (struct pci_dev *pdev,
+			             enum pci_channel_state state)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct ixgb_adapter *adapter = netdev->priv;
+
+	if(netif_running(netdev))
+		ixgb_down(adapter, TRUE);
+
+	pci_disable_device(pdev);
+
+	/* Request a slot reset. */
+	return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * ixgb_io_slot_reset - called after the pci bus has been reset.
+ * @pdev    pointer to pci device with error
+ *
+ * This callback is called after the PCI buss has been reset.
+ * Basically, this tries to restart the card from scratch.
+ * This is a shortened version of the device probe/discovery code,
+ * it resembles the first-half of the ixgb_probe() routine.
+ */
+static pci_ers_result_t ixgb_io_slot_reset (struct pci_dev *pdev)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct ixgb_adapter *adapter = netdev->priv;
+
+	if(pci_enable_device(pdev)) {
+		DPRINTK(PROBE, ERR, "Cannot re-enable PCI device after reset.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	/* Perform card reset only on one instance of the card */
+	if (0 != PCI_FUNC (pdev->devfn))
+		return PCI_ERS_RESULT_RECOVERED;
+
+	pci_set_master(pdev);
+
+	netif_carrier_off(netdev);
+	netif_stop_queue(netdev);
+	ixgb_reset(adapter);
+
+	/* Make sure the EEPROM is good */
+	if(!ixgb_validate_eeprom_checksum(&adapter->hw)) {
+		DPRINTK(PROBE, ERR, "After reset, the EEPROM checksum is not valid.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+	ixgb_get_ee_mac_addr(&adapter->hw, netdev->dev_addr);
+	memcpy(netdev->perm_addr, netdev->dev_addr, netdev->addr_len);
+
+	if(!is_valid_ether_addr(netdev->perm_addr)) {
+		DPRINTK(PROBE, ERR, "After reset, invalid MAC address.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * ixgb_io_resume - called when its OK to resume normal operations
+ * @pdev    pointer to pci device with error
+ *
+ * The error recovery driver tells us that its OK to resume
+ * normal operation. Implementation resembles the second-half
+ * of the ixgb_probe() routine.
+ */
+static void ixgb_io_resume (struct pci_dev *pdev)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct ixgb_adapter *adapter = netdev->priv;
+
+	pci_set_master(pdev);
+
+	if(netif_running(netdev)) {
+		if(ixgb_up(adapter)) {
+			printk ("ixgb: can't bring device back up after reset\n");
+			return;
+		}
+	}
+
+	netif_device_attach(netdev);
+	mod_timer(&adapter->watchdog_timer, jiffies);
+}
+
 /* ixgb_main.c */