rt2x00: Move all register definitions for rt2800 to rt2800.h.

There is no point on having them separated across 3 files.
At the same time rename USB_CYC_CFG to its proper name US_CYC_CNT
(as per the datasheet).

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>

drivers/net/wireless/rt2x00/rt2800.h

@@ -97,6 +97,21 @@
  * Registers.
  */
 
+/*
+ * E2PROM_CSR: PCI EEPROM control register.
+ * RELOAD: Write 1 to reload eeprom content.
+ * TYPE: 0: 93c46, 1:93c66.
+ * LOAD_STATUS: 1:loading, 0:done.
+ */
+#define E2PROM_CSR			0x0004
+#define E2PROM_CSR_DATA_CLOCK		FIELD32(0x00000001)
+#define E2PROM_CSR_CHIP_SELECT		FIELD32(0x00000002)
+#define E2PROM_CSR_DATA_IN		FIELD32(0x00000004)
+#define E2PROM_CSR_DATA_OUT		FIELD32(0x00000008)
+#define E2PROM_CSR_TYPE			FIELD32(0x00000030)
+#define E2PROM_CSR_LOAD_STATUS		FIELD32(0x00000040)
+#define E2PROM_CSR_RELOAD		FIELD32(0x00000080)
+
 /*
  * OPT_14: Unknown register used by rt3xxx devices.
  */
@@ -320,6 +335,39 @@
 #define RX_CRX_IDX			0x0298
 #define RX_DRX_IDX			0x029c
 
+/*
+ * USB_DMA_CFG
+ * RX_BULK_AGG_TIMEOUT: Rx Bulk Aggregation TimeOut in unit of 33ns.
+ * RX_BULK_AGG_LIMIT: Rx Bulk Aggregation Limit in unit of 256 bytes.
+ * PHY_CLEAR: phy watch dog enable.
+ * TX_CLEAR: Clear USB DMA TX path.
+ * TXOP_HALT: Halt TXOP count down when TX buffer is full.
+ * RX_BULK_AGG_EN: Enable Rx Bulk Aggregation.
+ * RX_BULK_EN: Enable USB DMA Rx.
+ * TX_BULK_EN: Enable USB DMA Tx.
+ * EP_OUT_VALID: OUT endpoint data valid.
+ * RX_BUSY: USB DMA RX FSM busy.
+ * TX_BUSY: USB DMA TX FSM busy.
+ */
+#define USB_DMA_CFG			0x02a0
+#define USB_DMA_CFG_RX_BULK_AGG_TIMEOUT	FIELD32(0x000000ff)
+#define USB_DMA_CFG_RX_BULK_AGG_LIMIT	FIELD32(0x0000ff00)
+#define USB_DMA_CFG_PHY_CLEAR		FIELD32(0x00010000)
+#define USB_DMA_CFG_TX_CLEAR		FIELD32(0x00080000)
+#define USB_DMA_CFG_TXOP_HALT		FIELD32(0x00100000)
+#define USB_DMA_CFG_RX_BULK_AGG_EN	FIELD32(0x00200000)
+#define USB_DMA_CFG_RX_BULK_EN		FIELD32(0x00400000)
+#define USB_DMA_CFG_TX_BULK_EN		FIELD32(0x00800000)
+#define USB_DMA_CFG_EP_OUT_VALID	FIELD32(0x3f000000)
+#define USB_DMA_CFG_RX_BUSY		FIELD32(0x40000000)
+#define USB_DMA_CFG_TX_BUSY		FIELD32(0x80000000)
+
+/*
+ * US_CYC_CNT
+ */
+#define US_CYC_CNT			0x02a4
+#define US_CYC_CNT_CLOCK_CYCLE		FIELD32(0x000000ff)
+
 /*
  * PBF_SYS_CTRL
  * HOST_RAM_WRITE: enable Host program ram write selection

drivers/net/wireless/rt2x00/rt2800lib.c

@@ -1620,9 +1620,9 @@ int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
 	rt2800_register_write(rt2x00dev, HW_BEACON_BASE7, 0);
 
 	if (rt2x00_is_usb(rt2x00dev)) {
-		rt2800_register_read(rt2x00dev, USB_CYC_CFG, &reg);
-		rt2x00_set_field32(&reg, USB_CYC_CFG_CLOCK_CYCLE, 30);
-		rt2800_register_write(rt2x00dev, USB_CYC_CFG, reg);
+		rt2800_register_read(rt2x00dev, US_CYC_CNT, &reg);
+		rt2x00_set_field32(&reg, US_CYC_CNT_CLOCK_CYCLE, 30);
+		rt2800_register_write(rt2x00dev, US_CYC_CNT, reg);
 	}
 
 	rt2800_register_read(rt2x00dev, HT_FBK_CFG0, &reg);

drivers/net/wireless/rt2x00/rt2800pci.h

@@ -34,25 +34,6 @@
 #ifndef RT2800PCI_H
 #define RT2800PCI_H
 
-/*
- * PCI registers.
- */
-
-/*
- * E2PROM_CSR: EEPROM control register.
- * RELOAD: Write 1 to reload eeprom content.
- * TYPE: 0: 93c46, 1:93c66.
- * LOAD_STATUS: 1:loading, 0:done.
- */
-#define E2PROM_CSR			0x0004
-#define E2PROM_CSR_DATA_CLOCK		FIELD32(0x00000001)
-#define E2PROM_CSR_CHIP_SELECT		FIELD32(0x00000002)
-#define E2PROM_CSR_DATA_IN		FIELD32(0x00000004)
-#define E2PROM_CSR_DATA_OUT		FIELD32(0x00000008)
-#define E2PROM_CSR_TYPE			FIELD32(0x00000030)
-#define E2PROM_CSR_LOAD_STATUS		FIELD32(0x00000040)
-#define E2PROM_CSR_RELOAD		FIELD32(0x00000080)
-
 /*
  * Queue register offset macros
  */

drivers/net/wireless/rt2x00/rt2800usb.h

@@ -31,43 +31,6 @@
 #ifndef RT2800USB_H
 #define RT2800USB_H
 
-/*
- * USB registers.
- */
-
-/*
- * USB_DMA_CFG
- * RX_BULK_AGG_TIMEOUT: Rx Bulk Aggregation TimeOut in unit of 33ns.
- * RX_BULK_AGG_LIMIT: Rx Bulk Aggregation Limit in unit of 256 bytes.
- * PHY_CLEAR: phy watch dog enable.
- * TX_CLEAR: Clear USB DMA TX path.
- * TXOP_HALT: Halt TXOP count down when TX buffer is full.
- * RX_BULK_AGG_EN: Enable Rx Bulk Aggregation.
- * RX_BULK_EN: Enable USB DMA Rx.
- * TX_BULK_EN: Enable USB DMA Tx.
- * EP_OUT_VALID: OUT endpoint data valid.
- * RX_BUSY: USB DMA RX FSM busy.
- * TX_BUSY: USB DMA TX FSM busy.
- */
-#define USB_DMA_CFG			0x02a0
-#define USB_DMA_CFG_RX_BULK_AGG_TIMEOUT	FIELD32(0x000000ff)
-#define USB_DMA_CFG_RX_BULK_AGG_LIMIT	FIELD32(0x0000ff00)
-#define USB_DMA_CFG_PHY_CLEAR		FIELD32(0x00010000)
-#define USB_DMA_CFG_TX_CLEAR		FIELD32(0x00080000)
-#define USB_DMA_CFG_TXOP_HALT		FIELD32(0x00100000)
-#define USB_DMA_CFG_RX_BULK_AGG_EN	FIELD32(0x00200000)
-#define USB_DMA_CFG_RX_BULK_EN		FIELD32(0x00400000)
-#define USB_DMA_CFG_TX_BULK_EN		FIELD32(0x00800000)
-#define USB_DMA_CFG_EP_OUT_VALID	FIELD32(0x3f000000)
-#define USB_DMA_CFG_RX_BUSY		FIELD32(0x40000000)
-#define USB_DMA_CFG_TX_BUSY		FIELD32(0x80000000)
-
-/*
- * USB_CYC_CFG
- */
-#define USB_CYC_CFG			0x02a4
-#define USB_CYC_CFG_CLOCK_CYCLE		FIELD32(0x000000ff)
-
 /*
  * 8051 firmware image.
  */