bnx2x: Parity errors handling for 57710 and 57711

This patch introduces the parity errors handling code for 57710 and 57711 chips.

HW is configured to stop all DMA transactions to the host and sending packets to the network
once parity error is detected, which is meant to prevent silent data corruption.
At the same time HW generates the attention interrupt to every function of the device where parity
has been detected so that driver can start the recovery flow.

The recovery is actually resetting the chip and restarting the driver on all active functions
of the chip where the parity error has been reported.

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/bnx2x.h

@@ -155,9 +155,15 @@ do {								 \
 #define SHMEM2_RD(bp, field)		REG_RD(bp, SHMEM2_ADDR(bp, field))
 #define SHMEM2_WR(bp, field, val)	REG_WR(bp, SHMEM2_ADDR(bp, field), val)
 
+#define MF_CFG_RD(bp, field)		SHMEM_RD(bp, mf_cfg.field)
+#define MF_CFG_WR(bp, field, val)	SHMEM_WR(bp, mf_cfg.field, val)
+
 #define EMAC_RD(bp, reg)		REG_RD(bp, emac_base + reg)
 #define EMAC_WR(bp, reg, val)		REG_WR(bp, emac_base + reg, val)
 
+#define AEU_IN_ATTN_BITS_PXPPCICLOCKCLIENT_PARITY_ERROR \
+	AEU_INPUTS_ATTN_BITS_PXPPCICLOCKCLIENT_PARITY_ERROR
+
 
 /* fast path */
 
@@ -818,6 +824,12 @@ struct attn_route {
 	u32	sig[4];
 };
 
+typedef enum {
+	BNX2X_RECOVERY_DONE,
+	BNX2X_RECOVERY_INIT,
+	BNX2X_RECOVERY_WAIT,
+} bnx2x_recovery_state_t;
+
 struct bnx2x {
 	/* Fields used in the tx and intr/napi performance paths
 	 * are grouped together in the beginning of the structure
@@ -835,6 +847,9 @@ struct bnx2x {
 	struct pci_dev		*pdev;
 
 	atomic_t		intr_sem;
+
+	bnx2x_recovery_state_t	recovery_state;
+	int			is_leader;
 #ifdef BCM_CNIC
 	struct msix_entry	msix_table[MAX_CONTEXT+2];
 #else
@@ -924,8 +939,7 @@ struct bnx2x {
 	int			mrrs;
 
 	struct delayed_work	sp_task;
-	struct work_struct	reset_task;
-
+	struct delayed_work	reset_task;
 	struct timer_list	timer;
 	int			current_interval;
 
@@ -1125,6 +1139,7 @@ static inline u32 reg_poll(struct bnx2x *bp, u32 reg, u32 expected, int ms,
 #define LOAD_DIAG			2
 #define UNLOAD_NORMAL			0
 #define UNLOAD_CLOSE			1
+#define UNLOAD_RECOVERY                 2
 
 
 /* DMAE command defines */
@@ -1294,6 +1309,10 @@ static inline u32 reg_poll(struct bnx2x *bp, u32 reg, u32 expected, int ms,
 				 AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR | \
 				 AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR)
 
+#define HW_PRTY_ASSERT_SET_3 (AEU_INPUTS_ATTN_BITS_MCP_LATCHED_ROM_PARITY | \
+		AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_RX_PARITY | \
+		AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_TX_PARITY | \
+		AEU_INPUTS_ATTN_BITS_MCP_LATCHED_SCPAD_PARITY)
 
 #define MULTI_FLAGS(bp) \
 		(TSTORM_ETH_FUNCTION_COMMON_CONFIG_RSS_IPV4_CAPABILITY | \

drivers/net/bnx2x_reg.h

@@ -766,6 +766,8 @@
 #define MCP_REG_MCPR_NVM_SW_ARB 				 0x86420
 #define MCP_REG_MCPR_NVM_WRITE					 0x86408
 #define MCP_REG_MCPR_SCRATCH					 0xa0000
+#define MISC_AEU_GENERAL_MASK_REG_AEU_NIG_CLOSE_MASK		 (0x1<<1)
+#define MISC_AEU_GENERAL_MASK_REG_AEU_PXP_CLOSE_MASK		 (0x1<<0)
 /* [R 32] read first 32 bit after inversion of function 0. mapped as
    follows: [0] NIG attention for function0; [1] NIG attention for
    function1; [2] GPIO1 mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp;
@@ -1249,6 +1251,8 @@
 #define MISC_REG_E1HMF_MODE					 0xa5f8
 /* [RW 32] Debug only: spare RW register reset by core reset */
 #define MISC_REG_GENERIC_CR_0					 0xa460
+/* [RW 32] Debug only: spare RW register reset by por reset */
+#define MISC_REG_GENERIC_POR_1					 0xa474
 /* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of
    these bits is written as a '1'; the corresponding SPIO bit will turn off
    it's drivers and become an input. This is the reset state of all GPIO
@@ -1438,7 +1442,7 @@
    (~misc_registers_sw_timer_cfg_4.sw_timer_cfg_4[1] ) is set */
 #define MISC_REG_SW_TIMER_RELOAD_VAL_4				 0xa2fc
 /* [RW 32] the value of the counter for sw timers1-8. there are 8 addresses
-   in this register. addres 0 - timer 1; address - timer 2�address 7 -
+   in this register. addres 0 - timer 1; address 1 - timer 2, ...  address 7 -
    timer 8 */
 #define MISC_REG_SW_TIMER_VAL					 0xa5c0
 /* [RW 1] Set by the MCP to remember if one or more of the drivers is/are
@@ -2407,10 +2411,16 @@
 /* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means
    this client is waiting for the arbiter. */
 #define PXP_REG_HST_CLIENTS_WAITING_TO_ARB			 0x103008
+/* [RW 1] When 1; doorbells are discarded and not passed to doorbell queue
+   block. Should be used for close the gates. */
+#define PXP_REG_HST_DISCARD_DOORBELLS				 0x1030a4
 /* [R 1] debug only: '1' means this PSWHST is discarding doorbells. This bit
    should update accoring to 'hst_discard_doorbells' register when the state
    machine is idle */
 #define PXP_REG_HST_DISCARD_DOORBELLS_STATUS			 0x1030a0
+/* [RW 1] When 1; new internal writes arriving to the block are discarded.
+   Should be used for close the gates. */
+#define PXP_REG_HST_DISCARD_INTERNAL_WRITES			 0x1030a8
 /* [R 6] debug only: A bit mask for all PSWHST internal write clients. '1'
    means this PSWHST is discarding inputs from this client. Each bit should
    update accoring to 'hst_discard_internal_writes' register when the state
@@ -4422,11 +4432,21 @@
 #define MISC_REGISTERS_GPIO_PORT_SHIFT				 4
 #define MISC_REGISTERS_GPIO_SET_POS				 8
 #define MISC_REGISTERS_RESET_REG_1_CLEAR			 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_HC			 (0x1<<29)
 #define MISC_REGISTERS_RESET_REG_1_RST_NIG			 (0x1<<7)
+#define MISC_REGISTERS_RESET_REG_1_RST_PXP			 (0x1<<26)
+#define MISC_REGISTERS_RESET_REG_1_RST_PXPV			 (0x1<<27)
 #define MISC_REGISTERS_RESET_REG_1_SET				 0x584
 #define MISC_REGISTERS_RESET_REG_2_CLEAR			 0x598
 #define MISC_REGISTERS_RESET_REG_2_RST_BMAC0			 (0x1<<0)
 #define MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE		 (0x1<<14)
+#define MISC_REGISTERS_RESET_REG_2_RST_EMAC1_HARD_CORE		 (0x1<<15)
+#define MISC_REGISTERS_RESET_REG_2_RST_GRC			 (0x1<<4)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_HARD_CORE_RST_B	 (0x1<<6)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_REG_HARD_CORE (0x1<<5)
+#define MISC_REGISTERS_RESET_REG_2_RST_MDIO			 (0x1<<13)
+#define MISC_REGISTERS_RESET_REG_2_RST_MISC_CORE		 (0x1<<11)
+#define MISC_REGISTERS_RESET_REG_2_RST_RBCN			 (0x1<<9)
 #define MISC_REGISTERS_RESET_REG_2_SET				 0x594
 #define MISC_REGISTERS_RESET_REG_3_CLEAR			 0x5a8
 #define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ	 (0x1<<1)
@@ -4454,6 +4474,7 @@
 #define HW_LOCK_RESOURCE_GPIO					 1
 #define HW_LOCK_RESOURCE_MDIO					 0
 #define HW_LOCK_RESOURCE_PORT0_ATT_MASK 			 3
+#define HW_LOCK_RESOURCE_RESERVED_08				 8
 #define HW_LOCK_RESOURCE_SPIO					 2
 #define HW_LOCK_RESOURCE_UNDI					 5
 #define PRS_FLAG_OVERETH_IPV4					 1
@@ -4474,6 +4495,10 @@
 #define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0		      (1<<5)
 #define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1		      (1<<9)
 #define AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR		      (1<<12)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_ROM_PARITY	      (1<<28)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_SCPAD_PARITY	      (1<<31)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_RX_PARITY	      (1<<29)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_TX_PARITY	      (1<<30)
 #define AEU_INPUTS_ATTN_BITS_MISC_HW_INTERRUPT		      (1<<15)
 #define AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR		      (1<<14)
 #define AEU_INPUTS_ATTN_BITS_PARSER_PARITY_ERROR	      (1<<20)