mmc: fix comment typos

Correct spelling typo in drivers/mmc

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

drivers/mmc/core/sdio.c

@@ -641,7 +641,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	/*
 	 * If the host and card support UHS-I mode request the card
 	 * to switch to 1.8V signaling level.  No 1.8v signalling if
-	 * UHS mode is not enabled to maintain compatibilty and some
+	 * UHS mode is not enabled to maintain compatibility and some
 	 * systems that claim 1.8v signalling in fact do not support
 	 * it.
 	 */

drivers/mmc/host/at91_mci.c

@@ -356,7 +356,7 @@ static void at91_mci_handle_transmitted(struct at91mci_host *host)
 }
 
 /*
- * Update bytes tranfered count during a write operation
+ * Update bytes transfered count during a write operation
  */
 static void at91_mci_update_bytes_xfered(struct at91mci_host *host)
 {

drivers/mmc/host/atmel-mci.c

@@ -1021,7 +1021,7 @@ static void atmci_stop_transfer(struct atmel_mci *host)
 }
 
 /*
- * Stop data transfer because error(s) occured.
+ * Stop data transfer because error(s) occurred.
  */
 static void atmci_stop_transfer_pdc(struct atmel_mci *host)
 {

drivers/mmc/host/omap_hsmmc.c

@@ -445,7 +445,7 @@ static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host)
 	OMAP_HSMMC_WRITE(host->base, SYSCTL,
 		OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
 	if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
-		dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stoped\n");
+		dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n");
 }
 
 static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host,

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -315,7 +315,7 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
 		new_val = val & (SDHCI_CTRL_LED | \
 				SDHCI_CTRL_4BITBUS | \
 				SDHCI_CTRL_D3CD);
-		/* ensure the endianess */
+		/* ensure the endianness */
 		new_val |= ESDHC_HOST_CONTROL_LE;
 		/* bits 8&9 are reserved on mx25 */
 		if (!is_imx25_esdhc(imx_data)) {

drivers/mmc/host/vub300.c

@@ -806,7 +806,7 @@ static void command_res_completed(struct urb *urb)
 		 * we suspect a buggy USB host controller
 		 */
 	} else if (!vub300->data) {
-		/* this means that the command (typically CMD52) suceeded */
+		/* this means that the command (typically CMD52) succeeded */
 	} else if (vub300->resp.common.header_type != 0x02) {
 		/*
 		 * this is an error response from the VUB300 chip