Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5326/1: AFEB9260: Fix for i2c_board_info structure
  [ARM] mx31ads: Add missing include
  [ARM] MXC: Fix mxc_gpio_get(), which must read PSR register instead DR.
  [ARM] MX3: Use ioremap wrapper to map SoC devices nonshared
  [ARM] gpio_free might sleep, arm architecture
  [ARM] ep93xx: fix OHCI DMA mask
  leds: da903x: (da9030 only) led brightness reversed.
  [ARM] sharpsl_pm: fix compilation w/o CONFIG_PM
  [ARM] pcm037: map AIPS1 and AIPS2 as nonshared area
  [ARM] build fixes for netX serial driver
  [ARM] 5323/1: Remove outdated empeg documentation.
  [ARM] 5299/1: Add maintainer for Mobilepro 900/c
  [ARM] corgi_lcd: fix simultaneous compilation with corgi_bl
  [ARM] pxa/spitz: fix spi cs on spitz
  [ARM] 5322/1: Fix fastpath issue in mmci.c
  [ARM] xsc3: revert writethrough memory-type encoding change

Documentation/arm/empeg/README

@@ -1,13 +0,0 @@
-Empeg, Ltd's Empeg MP3 Car Audio Player
-
-The initial design is to go in your car, but you can use it at home, on a
-boat... almost anywhere. The principle is to store CD-quality music using
-MPEG technology onto a hard disk in the unit, and use the power of the
-embedded computer to serve up the music you want.
-
-For more details, see:
-
-	http://www.empeg.com
-
-
-

Documentation/arm/empeg/ir.txt

@@ -1,49 +0,0 @@
-Infra-red driver documentation.
-
-Mike Crowe <mac@empeg.com>
-(C) Empeg Ltd 1999
-
-Not a lot here yet :-)
-
-The Kenwood KCA-R6A remote control generates a sequence like the following:
-
-Go low for approx 16T (Around 9000us)
-Go high for approx 8T (Around 4000us)
-Go low for less than 2T (Around 750us)
-
-For each of the 32 bits
-  Go high for more than 2T (Around 1500us) == 1
-  Go high for less than T (Around 400us) == 0
-  Go low for less than 2T (Around 750us)
-
-Rather than repeat a signal when the button is held down certain buttons
-generate the following code to indicate repetition.
-
-Go low for approx 16T
-Go high for approx 4T
-Go low for less than 2T
-
-(By removing the <2T from the start of the sequence and placing at the end
- it can be considered a stop bit but I found it easier to deal with it at
- the start).
-
-The 32 bits are encoded as XxYy where x and y are the actual data values
-while X and Y are the logical inverses of the associated data values. Using 
-LSB first yields sensible codes for the numbers.
-
-All codes are of the form b9xx
-
-The numeric keys generate the code 0x where x is the number pressed.
-
-Tuner		1c
-Tape		1d
-CD		1e
-CD-MD-CH	1f
-Track-		0a
-Track+		0b
-Rewind		0c
-FF		0d
-DNPP		5e
-Play/Pause	0e
-Vol+		14
-Vol-		15

Documentation/arm/empeg/mkdevs

@@ -1,11 +0,0 @@
-#!/bin/sh
-mknod /dev/display c 244 0
-mknod /dev/ir c 242 0
-mknod /dev/usb0 c 243 0
-mknod /dev/audio c 245 4
-mknod /dev/dsp c 245 3
-mknod /dev/mixer c 245 0
-mknod /dev/empeg_state c 246 0
-mknod /dev/radio0 c 81 64
-ln -sf radio0 radio
-ln -sf usb0 usb

MAINTAINERS

@@ -610,6 +610,11 @@ P:	Philipp Zabel
 M:	philipp.zabel@gmail.com
 S:	Maintained
 
+ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT
+P:	Michael Petchkovsky
+M:	mkpetch@internode.on.net
+S:	Maintained
+
 ARM/TOSA MACHINE SUPPORT
 P:	Dmitry Baryshkov
 M:	dbaryshkov@gmail.com

arch/arm/common/sharpsl_pm.c

@@ -54,11 +54,13 @@
 /*
  * Prototypes
  */
+#ifdef CONFIG_PM
 static int sharpsl_off_charge_battery(void);
-static int sharpsl_check_battery_temp(void);
 static int sharpsl_check_battery_voltage(void);
-static int sharpsl_ac_check(void);
 static int sharpsl_fatal_check(void);
+#endif
+static int sharpsl_check_battery_temp(void);
+static int sharpsl_ac_check(void);
 static int sharpsl_average_value(int ad);
 static void sharpsl_average_clear(void);
 static void sharpsl_charge_toggle(struct work_struct *private_);
@@ -424,6 +426,7 @@ static int sharpsl_check_battery_temp(void)
 	return 0;
 }
 
+#ifdef CONFIG_PM
 static int sharpsl_check_battery_voltage(void)
 {
 	int val, i, buff[5];
@@ -455,6 +458,7 @@ static int sharpsl_check_battery_voltage(void)
 
 	return 0;
 }
+#endif
 
 static int sharpsl_ac_check(void)
 {
@@ -586,8 +590,6 @@ static int corgi_pxa_pm_enter(suspend_state_t state)
 
 	return 0;
 }
-#endif
-
 
 /*
  * Check for fatal battery errors
@@ -738,7 +740,10 @@ static int sharpsl_off_charge_battery(void)
 		}
 	}
 }
-
+#else
+#define sharpsl_pm_suspend	NULL
+#define sharpsl_pm_resume	NULL
+#endif
 
 static ssize_t battery_percentage_show(struct device *dev, struct device_attribute *attr, char *buf)
 {
@@ -768,10 +773,12 @@ static void sharpsl_apm_get_power_status(struct apm_power_info *info)
 	info->battery_life = sharpsl_pm.battstat.mainbat_percent;
 }
 
+#ifdef CONFIG_PM
 static struct platform_suspend_ops sharpsl_pm_ops = {
 	.enter		= corgi_pxa_pm_enter,
 	.valid		= suspend_valid_only_mem,
 };
+#endif
 
 static int __init sharpsl_pm_probe(struct platform_device *pdev)
 {
@@ -802,7 +809,9 @@ static int __init sharpsl_pm_probe(struct platform_device *pdev)
 
 	apm_get_power_status = sharpsl_apm_get_power_status;
 
+#ifdef CONFIG_PM
 	suspend_set_ops(&sharpsl_pm_ops);
+#endif
 
 	mod_timer(&sharpsl_pm.ac_timer, jiffies + msecs_to_jiffies(250));
 

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -165,6 +165,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 	{
 		I2C_BOARD_INFO("fm3130", 0x68),
+	}, {
 		I2C_BOARD_INFO("24c64", 0x50),
 	},
 };

arch/arm/mach-at91/include/mach/gpio.h

@@ -13,6 +13,7 @@
 #ifndef __ASM_ARCH_AT91RM9200_GPIO_H
 #define __ASM_ARCH_AT91RM9200_GPIO_H
 
+#include <linux/kernel.h>
 #include <asm/irq.h>
 
 #define PIN_BASE		NR_AIC_IRQS
@@ -220,6 +221,7 @@ static inline int gpio_request(unsigned gpio, const char *label)
 
 static inline void gpio_free(unsigned gpio)
 {
+	might_sleep();
 }
 
 extern int gpio_direction_input(unsigned gpio);

arch/arm/mach-ep93xx/core.c

@@ -26,6 +26,7 @@
 #include <linux/serial_core.h>
 #include <linux/device.h>
 #include <linux/mm.h>
+#include <linux/dma-mapping.h>
 #include <linux/time.h>
 #include <linux/timex.h>
 #include <linux/delay.h>
@@ -449,12 +450,13 @@ static struct resource ep93xx_ohci_resources[] = {
 	},
 };
 
+
 static struct platform_device ep93xx_ohci_device = {
 	.name		= "ep93xx-ohci",
 	.id		= -1,
 	.dev		= {
-		.dma_mask		= (void *)0xffffffff,
-		.coherent_dma_mask	= 0xffffffff,
+		.dma_mask		= &ep93xx_ohci_device.dev.coherent_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
 	},
 	.num_resources	= ARRAY_SIZE(ep93xx_ohci_resources),
 	.resource	= ep93xx_ohci_resources,

arch/arm/mach-imx/include/mach/gpio.h

@@ -1,5 +1,6 @@
 #ifndef _IMX_GPIO_H
 
+#include <linux/kernel.h>
 #include <mach/imx-regs.h>
 
 #define IMX_GPIO_ALLOC_MODE_NORMAL	0
@@ -63,6 +64,8 @@ static inline int gpio_request(unsigned gpio, const char *label)
 
 static inline void gpio_free(unsigned gpio)
 {
+	might_sleep();
+
 	imx_gpio_free(gpio);
 }
 

arch/arm/mach-ixp4xx/include/mach/gpio.h

@@ -25,6 +25,7 @@
 #ifndef __ASM_ARCH_IXP4XX_GPIO_H
 #define __ASM_ARCH_IXP4XX_GPIO_H
 
+#include <linux/kernel.h>
 #include <mach/hardware.h>
 
 static inline int gpio_request(unsigned gpio, const char *label)
@@ -34,6 +35,8 @@ static inline int gpio_request(unsigned gpio, const char *label)
 
 static inline void gpio_free(unsigned gpio)
 {
+	might_sleep();
+
 	return;
 }
 

arch/arm/mach-ks8695/include/mach/gpio.h

@@ -11,6 +11,8 @@
 #ifndef __ASM_ARCH_GPIO_H_
 #define __ASM_ARCH_GPIO_H_
 
+#include <linux/kernel.h>
+
 #define KS8695_GPIO_0		0
 #define KS8695_GPIO_1		1
 #define KS8695_GPIO_2		2
@@ -74,6 +76,7 @@ static inline int gpio_request(unsigned int pin, const char *label)
 
 static inline void gpio_free(unsigned int pin)
 {
+	might_sleep();
 }
 
 #endif

arch/arm/mach-mx3/mx31ads.c

@@ -35,6 +35,8 @@
 #include <mach/imx-uart.h>
 #include <mach/iomux-mx3.h>
 
+#include "devices.h"
+
 /*!
  * @file mx31ads.c
  *

arch/arm/mach-mx3/pcm037.c

@@ -91,12 +91,12 @@ static struct map_desc pcm037_io_desc[] __initdata = {
 		.virtual	= AIPS1_BASE_ADDR_VIRT,
 		.pfn		= __phys_to_pfn(AIPS1_BASE_ADDR),
 		.length		= AIPS1_SIZE,
-		.type		= MT_DEVICE
+		.type		= MT_DEVICE_NONSHARED
 	}, {
 		.virtual	= AIPS2_BASE_ADDR_VIRT,
 		.pfn		= __phys_to_pfn(AIPS2_BASE_ADDR),
 		.length		= AIPS2_SIZE,
-		.type		= MT_DEVICE
+		.type		= MT_DEVICE_NONSHARED
 	},
 };
 

arch/arm/mach-ns9xxx/gpio.c

@@ -8,6 +8,7 @@
  * under the terms of the GNU General Public License version 2 as published by
  * the Free Software Foundation.
  */
+#include <linux/kernel.h>
 #include <linux/compiler.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
@@ -63,6 +64,7 @@ EXPORT_SYMBOL(gpio_request);
 
 void gpio_free(unsigned gpio)
 {
+	might_sleep();
 	clear_bit(gpio, gpiores);
 	return;
 }

arch/arm/mach-orion5x/gpio.c

@@ -165,6 +165,8 @@ EXPORT_SYMBOL(gpio_request);
 
 void gpio_free(unsigned pin)
 {
+	might_sleep();
+
 	if (pin >= GPIO_MAX || !test_bit(pin, gpio_valid)) {
 		pr_debug("%s: invalid GPIO %d\n", __func__, pin);
 		return;

arch/arm/mach-pxa/corgi_pm.c

@@ -204,7 +204,9 @@ static struct sharpsl_charger_machinfo corgi_pm_machinfo = {
 	.read_devdata    = corgipm_read_devdata,
 	.charger_wakeup  = corgi_charger_wakeup,
 	.should_wakeup   = corgi_should_wakeup,
-#ifdef CONFIG_BACKLIGHT_CORGI
+#if defined(CONFIG_LCD_CORGI)
+	.backlight_limit = corgi_lcd_limit_intensity,
+#elif defined(CONFIG_BACKLIGHT_CORGI)
 	.backlight_limit = corgibl_limit_intensity,
 #endif
 	.charge_on_volt	  = SHARPSL_CHARGE_ON_VOLT,

arch/arm/mach-pxa/include/mach/sharpsl.h

@@ -26,6 +26,7 @@ struct corgits_machinfo {
  * SharpSL Backlight
  */
 extern void corgibl_limit_intensity(int limit);
+extern void corgi_lcd_limit_intensity(int limit);
 
 
 /*

arch/arm/mach-pxa/spitz.c

@@ -385,6 +385,16 @@ static void __init spitz_init_spi(void)
 	if (err)
 		goto err_free_2;
 
+	err = gpio_direction_output(SPITZ_GPIO_ADS7846_CS, 1);
+	if (err)
+		goto err_free_3;
+	err = gpio_direction_output(SPITZ_GPIO_LCDCON_CS, 1);
+	if (err)
+		goto err_free_3;
+	err = gpio_direction_output(SPITZ_GPIO_MAX1111_CS, 1);
+	if (err)
+		goto err_free_3;
+
 	if (machine_is_akita()) {
 		spitz_lcdcon_info.gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT;
 		spitz_lcdcon_info.gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON;
@@ -394,6 +404,8 @@ static void __init spitz_init_spi(void)
 	spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
 	return;
 
+err_free_3:
+	gpio_free(SPITZ_GPIO_MAX1111_CS);
 err_free_2:
 	gpio_free(SPITZ_GPIO_LCDCON_CS);
 err_free_1:

arch/arm/mach-pxa/spitz_pm.c

@@ -198,7 +198,9 @@ struct sharpsl_charger_machinfo spitz_pm_machinfo = {
 	.read_devdata     = spitzpm_read_devdata,
 	.charger_wakeup   = spitz_charger_wakeup,
 	.should_wakeup    = spitz_should_wakeup,
-#ifdef CONFIG_BACKLIGHT_CORGI
+#if defined(CONFIG_LCD_CORGI)
+	.backlight_limit = corgi_lcd_limit_intensity,
+#elif defined(CONFIG_BACKLIGHT_CORGI)
         .backlight_limit  = corgibl_limit_intensity,
 #endif
 	.charge_on_volt	  = SHARPSL_CHARGE_ON_VOLT,

arch/arm/mm/proc-xsc3.S

@@ -349,7 +349,7 @@ ENTRY(cpu_xsc3_switch_mm)
 cpu_xsc3_mt_table:
 	.long	0x00						@ L_PTE_MT_UNCACHED
 	.long	PTE_EXT_TEX(1)					@ L_PTE_MT_BUFFERABLE
-	.long	PTE_CACHEABLE					@ L_PTE_MT_WRITETHROUGH
+	.long	PTE_EXT_TEX(5) | PTE_CACHEABLE			@ L_PTE_MT_WRITETHROUGH
 	.long	PTE_CACHEABLE | PTE_BUFFERABLE			@ L_PTE_MT_WRITEBACK
 	.long	PTE_EXT_TEX(1) | PTE_BUFFERABLE			@ L_PTE_MT_DEV_SHARED
 	.long	0x00						@ unused

arch/arm/plat-mxc/gpio.c

@@ -188,7 +188,7 @@ static int mxc_gpio_get(struct gpio_chip *chip, unsigned offset)
 	struct mxc_gpio_port *port =
 		container_of(chip, struct mxc_gpio_port, chip);
 
-	return (__raw_readl(port->base + GPIO_DR) >> offset) & 1;
+	return (__raw_readl(port->base + GPIO_PSR) >> offset) & 1;
 }
 
 static int mxc_gpio_direction_input(struct gpio_chip *chip, unsigned offset)

arch/arm/plat-mxc/include/mach/io.h

@@ -14,6 +14,26 @@
 /* Allow IO space to be anywhere in the memory */
 #define IO_SPACE_LIMIT 0xffffffff
 
+#ifdef CONFIG_ARCH_MX3
+#define __arch_ioremap __mx3_ioremap
+#define __arch_iounmap __iounmap
+
+static inline void __iomem *
+__mx3_ioremap(unsigned long phys_addr, size_t size, unsigned int mtype)
+{
+	if (mtype == MT_DEVICE) {
+		/* Access all peripherals below 0x80000000 as nonshared device
+		 * but leave l2cc alone.
+		 */
+		if ((phys_addr < 0x80000000) && ((phys_addr < L2CC_BASE_ADDR) ||
+			(phys_addr >= L2CC_BASE_ADDR + L2CC_SIZE)))
+			mtype = MT_DEVICE_NONSHARED;
+	}
+
+	return __arm_ioremap(phys_addr, size, mtype);
+}
+#endif
+
 /* io address mapping macro */
 #define __io(a)			((void __iomem *)(a))
 

drivers/leds/leds-da903x.c

@@ -58,7 +58,7 @@ static void da903x_led_work(struct work_struct *work)
 		offset = DA9030_LED_OFFSET(led->id);
 		val = led->flags & ~0x87;
 		val |= (led->new_brightness) ? 0x80 : 0; /* EN bit */
-		val |= (led->new_brightness >> 5) & 0x7; /* PWM<2:0> */
+		val |= (0x7 - (led->new_brightness >> 5)) & 0x7; /* PWM<2:0> */
 		da903x_write(led->master, DA9030_LED1_CONTROL + offset, val);
 		break;
 	case DA9030_ID_VIBRA:

drivers/mmc/host/mmci.c

@@ -391,6 +391,7 @@ static irqreturn_t mmci_irq(int irq, void *dev_id)
 static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 {
 	struct mmci_host *host = mmc_priv(mmc);
+	unsigned long flags;
 
 	WARN_ON(host->mrq != NULL);
 
@@ -402,7 +403,7 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 		return;
 	}
 
-	spin_lock_irq(&host->lock);
+	spin_lock_irqsave(&host->lock, flags);
 
 	host->mrq = mrq;
 
@@ -411,7 +412,7 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 
 	mmci_start_command(host, mrq->cmd, 0);
 
-	spin_unlock_irq(&host->lock);
+	spin_unlock_irqrestore(&host->lock, flags);
 }
 
 static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)

drivers/serial/Kconfig

@@ -1276,7 +1276,7 @@ config SERIAL_SGI_IOC3
 	  say Y or M.  Otherwise, say N.
 
 config SERIAL_NETX
-	bool "NetX serial port support"
+	tristate "NetX serial port support"
 	depends on ARM && ARCH_NETX
 	select SERIAL_CORE
 	help
@@ -1288,7 +1288,7 @@ config SERIAL_NETX
 
 config SERIAL_NETX_CONSOLE
 	bool "Console on NetX serial port"
-	depends on SERIAL_NETX
+	depends on SERIAL_NETX=y
 	select SERIAL_CORE_CONSOLE
 	help
 	  If you have enabled the serial port on the Hilscher NetX SoC

drivers/serial/netx-serial.c

@@ -42,8 +42,6 @@
 #define SERIAL_NX_MAJOR	204
 #define MINOR_START	170
 
-#ifdef CONFIG_SERIAL_NETX_CONSOLE
-
 enum uart_regs {
 	UART_DR              = 0x00,
 	UART_SR              = 0x04,
@@ -528,6 +526,8 @@ static struct netx_port netx_ports[] = {
 	}
 };
 
+#ifdef CONFIG_SERIAL_NETX_CONSOLE
+
 static void netx_console_putchar(struct uart_port *port, int ch)
 {
 	while (readl(port->membase + UART_FR) & FR_BUSY);

drivers/video/backlight/corgi_lcd.c

@@ -439,7 +439,7 @@ static int corgi_bl_update_status(struct backlight_device *bd)
 	return corgi_bl_set_intensity(lcd, intensity);
 }
 
-void corgibl_limit_intensity(int limit)
+void corgi_lcd_limit_intensity(int limit)
 {
 	if (limit)
 		corgibl_flags |= CORGIBL_BATTLOW;
@@ -448,7 +448,7 @@ void corgibl_limit_intensity(int limit)
 
 	backlight_update_status(the_corgi_lcd->bl_dev);
 }
-EXPORT_SYMBOL(corgibl_limit_intensity);
+EXPORT_SYMBOL(corgi_lcd_limit_intensity);
 
 static struct backlight_ops corgi_bl_ops = {
 	.get_brightness	= corgi_bl_get_intensity,