staging: rtl8192e: Remove rf_chip variable, hardcode to RF_8256

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/rtl8192e/r8190_rtl8256.c

@@ -299,10 +299,7 @@ void PHY_SetRF8256OFDMTxPower(struct net_device* dev, u8 powerlevel)
 
 #define MAX_DOZE_WAITING_TIMES_9x 64
 static bool
-SetRFPowerState8190(
-	struct net_device* dev,
-	RT_RF_POWER_STATE	eRFPowerState
-	)
+SetRFPowerState8190(struct net_device *dev, RT_RF_POWER_STATE eRFPowerState)
 {
 	struct r8192_priv *priv = ieee80211_priv(dev);
 	PRT_POWER_SAVE_CONTROL	pPSC = (PRT_POWER_SAVE_CONTROL)(&(priv->ieee80211->PowerSaveControl));
@@ -314,147 +311,138 @@ SetRFPowerState8190(
 		return false;
 	priv->SetRFPowerStateInProgress = true;
 
-	switch(priv->rf_chip)
+	switch( eRFPowerState )
 	{
-		case RF_8256:
-		switch( eRFPowerState )
+	case eRfOn:
+
+		// turn on RF
+		if((priv->ieee80211->eRFPowerState == eRfOff) && RT_IN_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC))
+		{ // The current RF state is OFF and the RF OFF level is halting the NIC, re-initialize the NIC.
+			bool rtstatus = true;
+			u32 InitializeCount = 3;
+			do
+			{
+				InitializeCount--;
+				rtstatus = NicIFEnableNIC(dev);
+			}while( (rtstatus != true) &&(InitializeCount >0) );
+
+			if(rtstatus != true)
+			{
+				RT_TRACE(COMP_ERR,"%s():Initialize Adapter fail,return\n",__FUNCTION__);
+				priv->SetRFPowerStateInProgress = false;
+				return false;
+			}
+
+			RT_CLEAR_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC);
+		} else {
+			write_nic_byte(priv, ANAPAR, 0x37);//160MHz
+			mdelay(1);
+			//enable clock 80/88 MHz
+			rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x4, 0x1); // 0x880[2]
+			priv->bHwRfOffAction = 0;
+
+			//RF-A, RF-B
+			//enable RF-Chip A/B
+			rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT4, 0x1);		// 0x860[4]
+			//analog to digital on
+			rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
+			//digital to analog on
+			rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18, 0x3); // 0x880[4:3]
+			//rx antenna on
+			rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0x3, 0x3);// 0xc04[1:0]
+			//rx antenna on
+			rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0x3, 0x3);// 0xd04[1:0]
+			//analog to digital part2 on
+			rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60, 0x3); 	// 0x880[6:5]
+
+		}
+
+		break;
+
+	//
+	// In current solution, RFSleep=RFOff in order to save power under 802.11 power save.
+	// By Bruce, 2008-01-16.
+	//
+	case eRfSleep:
+
+		// HW setting had been configured with deeper mode.
+		if(priv->ieee80211->eRFPowerState == eRfOff)
+			break;
+
+		for(QueueID = 0, i = 0; QueueID < MAX_TX_QUEUE; )
 		{
-			case eRfOn:
-
-				// turn on RF
-				if((priv->ieee80211->eRFPowerState == eRfOff) && RT_IN_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC))
-				{ // The current RF state is OFF and the RF OFF level is halting the NIC, re-initialize the NIC.
-					bool rtstatus = true;
-					u32 InitializeCount = 3;
-					do
-					{
-						InitializeCount--;
-						rtstatus = NicIFEnableNIC(dev);
-					}while( (rtstatus != true) &&(InitializeCount >0) );
-
-					if(rtstatus != true)
-					{
-						RT_TRACE(COMP_ERR,"%s():Initialize Adapter fail,return\n",__FUNCTION__);
-						priv->SetRFPowerStateInProgress = false;
-						return false;
-					}
-
-					RT_CLEAR_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC);
-				} else {
-					write_nic_byte(priv, ANAPAR, 0x37);//160MHz
-					mdelay(1);
-					//enable clock 80/88 MHz
-					rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x4, 0x1); // 0x880[2]
-					priv->bHwRfOffAction = 0;
-
-					//RF-A, RF-B
-					//enable RF-Chip A/B
-					rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT4, 0x1);		// 0x860[4]
-					//analog to digital on
-					rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
-					//digital to analog on
-					rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18, 0x3); // 0x880[4:3]
-					//rx antenna on
-					rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0x3, 0x3);// 0xc04[1:0]
-					//rx antenna on
-					rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0x3, 0x3);// 0xd04[1:0]
-					//analog to digital part2 on
-					rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60, 0x3); 	// 0x880[6:5]
+			ring = &priv->tx_ring[QueueID];
 
-				}
+			if(skb_queue_len(&ring->queue) == 0)
+			{
+				QueueID++;
+				continue;
+			}
+			else
+			{
+				RT_TRACE((COMP_POWER|COMP_RF), "eRf Off/Sleep: %d times TcbBusyQueue[%d] !=0 before doze!\n", (i+1), QueueID);
+				udelay(10);
+				i++;
+			}
 
+			if(i >= MAX_DOZE_WAITING_TIMES_9x)
+			{
+				RT_TRACE(COMP_POWER, "\n\n\n TimeOut!! SetRFPowerState8190(): eRfOff: %d times TcbBusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_9x, QueueID);
 				break;
+			}
+		}
 
-				//
-				// In current solution, RFSleep=RFOff in order to save power under 802.11 power save.
-				// By Bruce, 2008-01-16.
-				//
-			case eRfSleep:
-
-				// HW setting had been configured with deeper mode.
-				if(priv->ieee80211->eRFPowerState == eRfOff)
-					break;
-
-					for(QueueID = 0, i = 0; QueueID < MAX_TX_QUEUE; )
-					{
-							ring = &priv->tx_ring[QueueID];
-
-							if(skb_queue_len(&ring->queue) == 0)
-							{
-								QueueID++;
-								continue;
-							}
-							else
-							{
-								RT_TRACE((COMP_POWER|COMP_RF), "eRf Off/Sleep: %d times TcbBusyQueue[%d] !=0 before doze!\n", (i+1), QueueID);
-								udelay(10);
-								i++;
-							}
-
-							if(i >= MAX_DOZE_WAITING_TIMES_9x)
-							{
-								RT_TRACE(COMP_POWER, "\n\n\n TimeOut!! SetRFPowerState8190(): eRfOff: %d times TcbBusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_9x, QueueID);
-								break;
-							}
-						}
-
-				PHY_SetRtl8192eRfOff(dev);
+		PHY_SetRtl8192eRfOff(dev);
 
-				break;
+		break;
 
-			case eRfOff:
+	case eRfOff:
 
-				//
-				// Disconnect with Any AP or STA.
-				//
-				for(QueueID = 0, i = 0; QueueID < MAX_TX_QUEUE; )
-				{
-					ring = &priv->tx_ring[QueueID];
-
-					if(skb_queue_len(&ring->queue) == 0)
-						{
-							QueueID++;
-							continue;
-						}
-						else
-						{
-							RT_TRACE(COMP_POWER,
-							"eRf Off/Sleep: %d times TcbBusyQueue[%d] !=0 before doze!\n", (i+1), QueueID);
-							udelay(10);
-							i++;
-						}
-
-						if(i >= MAX_DOZE_WAITING_TIMES_9x)
-						{
-							RT_TRACE(COMP_POWER, "\n\n\n SetZebraRFPowerState8185B(): eRfOff: %d times TcbBusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_9x, QueueID);
-							break;
-						}
-				}
+		//
+		// Disconnect with Any AP or STA.
+		//
+		for(QueueID = 0, i = 0; QueueID < MAX_TX_QUEUE; )
+		{
+			ring = &priv->tx_ring[QueueID];
 
+			if(skb_queue_len(&ring->queue) == 0)
+			{
+				QueueID++;
+				continue;
+			}
+			else
+			{
+				RT_TRACE(COMP_POWER,
+				"eRf Off/Sleep: %d times TcbBusyQueue[%d] !=0 before doze!\n", (i+1), QueueID);
+				udelay(10);
+				i++;
+			}
 
-					if (pPSC->RegRfPsLevel & RT_RF_OFF_LEVL_HALT_NIC && !RT_IN_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC))
-					{ // Disable all components.
-						NicIFDisableNIC(dev);
-						RT_SET_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC);
-					}
-					else if (!(pPSC->RegRfPsLevel & RT_RF_OFF_LEVL_HALT_NIC))
-					{ // Normal case.
-				  		// IPS should go to this.
-						PHY_SetRtl8192eRfOff(dev);
-					}
+			if(i >= MAX_DOZE_WAITING_TIMES_9x)
+			{
+				RT_TRACE(COMP_POWER, "\n\n\n SetZebraRFPowerState8185B(): eRfOff: %d times TcbBusyQueue[%d] != 0 !!!\n\n\n", MAX_DOZE_WAITING_TIMES_9x, QueueID);
 				break;
-
-			default:
-					bResult = false;
-					RT_TRACE(COMP_ERR, "SetRFPowerState8190(): unknow state to set: 0x%X!!!\n", eRFPowerState);
-					break;
+			}
 		}
 
+
+		if (pPSC->RegRfPsLevel & RT_RF_OFF_LEVL_HALT_NIC && !RT_IN_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC))
+		{
+			/* Disable all components. */
+			NicIFDisableNIC(dev);
+			RT_SET_PS_LEVEL(pPSC, RT_RF_OFF_LEVL_HALT_NIC);
+		}
+		else if (!(pPSC->RegRfPsLevel & RT_RF_OFF_LEVL_HALT_NIC))
+		{
+			/* Normal case - IPS should go to this. */
+			PHY_SetRtl8192eRfOff(dev);
+		}
 		break;
 
-		default:
-			RT_TRACE(COMP_ERR, "SetRFPowerState8190(): Unknown RF type\n");
-			break;
+	default:
+		bResult = false;
+		RT_TRACE(COMP_ERR, "SetRFPowerState8190(): unknow state to set: 0x%X!!!\n", eRFPowerState);
+		break;
 	}
 
 	if(bResult)

drivers/staging/rtl8192e/r8192E.h

@@ -543,15 +543,6 @@ typedef struct _BB_REGISTER_DEFINITION{
 	u32 rfLSSIReadBack; 	//LSSI RF readback data //		0x8a0~0x8af [16 bytes]
 }BB_REGISTER_DEFINITION_T, *PBB_REGISTER_DEFINITION_T;
 
-typedef enum _RT_RF_TYPE_819xU{
-        RF_TYPE_MIN = 0,
-        RF_8225,
-        RF_8256,
-        RF_8258,
-        RF_PSEUDO_11N = 4,
-}RT_RF_TYPE_819xU, *PRT_RF_TYPE_819xU;
-
-
 typedef struct _rate_adaptive
 {
 	u8				rate_adaptive_disabled;
@@ -852,7 +843,6 @@ typedef struct r8192_priv
 	struct semaphore wx_sem;
 	struct semaphore rf_sem; //used to lock rf write operation added by wb, modified by david
 	u8 rf_type; /* 0 means 1T2R, 1 means 2T4R */
-	RT_RF_TYPE_819xU rf_chip;
 
 	short (*rf_set_sens)(struct net_device *dev,short sens);
 	u8 (*rf_set_chan)(struct net_device *dev,u8 ch);

drivers/staging/rtl8192e/r8192E_core.c

@@ -152,15 +152,9 @@ static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv* priv)
 			Dot11d_Init(ieee);
 			ieee->bGlobalDomain = false;
                         //acturally 8225 & 8256 rf chip only support B,G,24N mode
-                        if ((priv->rf_chip == RF_8225) || (priv->rf_chip == RF_8256))
-			{
-				min_chan = 1;
-				max_chan = 14;
-			}
-			else
-			{
-				RT_TRACE(COMP_ERR, "unknown rf chip, can't set channel map in function:%s()\n", __FUNCTION__);
-			}
+			min_chan = 1;
+			max_chan = 14;
+
 			if (ChannelPlan[channel_plan].Len != 0){
 				// Clear old channel map
 				memset(GET_DOT11D_INFO(ieee)->channel_map, 0, sizeof(GET_DOT11D_INFO(ieee)->channel_map));
@@ -1832,25 +1826,9 @@ static void rtl8192_refresh_supportrate(struct r8192_priv* priv)
 		memset(ieee->Regdot11HTOperationalRateSet, 0, 16);
 }
 
-static u8 rtl8192_getSupportedWireleeMode(struct net_device*dev)
+static u8 rtl8192_getSupportedWireleeMode(struct net_device *dev)
 {
-	struct r8192_priv *priv = ieee80211_priv(dev);
-	u8 ret = 0;
-	switch(priv->rf_chip)
-	{
-		case RF_8225:
-		case RF_8256:
-		case RF_PSEUDO_11N:
-			ret = (WIRELESS_MODE_N_24G|WIRELESS_MODE_G|WIRELESS_MODE_B);
-			break;
-		case RF_8258:
-			ret = (WIRELESS_MODE_A|WIRELESS_MODE_N_5G);
-			break;
-		default:
-			ret = WIRELESS_MODE_B;
-			break;
-	}
-	return ret;
+	return (WIRELESS_MODE_N_24G|WIRELESS_MODE_G|WIRELESS_MODE_B);
 }
 
 static void rtl8192_SetWirelessMode(struct net_device* dev, u8 wireless_mode)
@@ -2480,8 +2458,6 @@ static void rtl8192_read_eeprom_info(struct r8192_priv *priv)
 
 	//1 Make a copy for following variables and we can change them if we want
 
-	priv->rf_chip= RF_8256;
-
 	if(priv->RegChannelPlan == 0xf)
 	{
 		priv->ChannelPlan = priv->eeprom_ChannelPlan;

drivers/staging/rtl8192e/r819xE_phy.c

@@ -669,35 +669,28 @@ static u32 rtl8192_phy_RFSerialRead(struct net_device* dev, RF90_RADIO_PATH_E eR
 	Offset &= 0x3f;
 
 	//switch page for 8256 RF IC
-	if (priv->rf_chip == RF_8256)
+	//analog to digital off, for protection
+	rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
+	if (Offset >= 31)
 	{
-		//analog to digital off, for protection
-		rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
-		if (Offset >= 31)
-		{
-			priv->RfReg0Value[eRFPath] |= 0x140;
-			//Switch to Reg_Mode2 for Reg 31-45
-			rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
-			//modify offset
-			NewOffset = Offset -30;
-		}
-		else if (Offset >= 16)
-		{
-			priv->RfReg0Value[eRFPath] |= 0x100;
-			priv->RfReg0Value[eRFPath] &= (~0x40);
-			//Switch to Reg_Mode 1 for Reg16-30
-			rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
+		priv->RfReg0Value[eRFPath] |= 0x140;
+		//Switch to Reg_Mode2 for Reg 31-45
+		rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
+		//modify offset
+		NewOffset = Offset -30;
+	}
+	else if (Offset >= 16)
+	{
+		priv->RfReg0Value[eRFPath] |= 0x100;
+		priv->RfReg0Value[eRFPath] &= (~0x40);
+		//Switch to Reg_Mode 1 for Reg16-30
+		rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16) );
 
-			NewOffset = Offset - 15;
-		}
-		else
-			NewOffset = Offset;
+		NewOffset = Offset - 15;
 	}
 	else
-	{
-		RT_TRACE((COMP_PHY|COMP_ERR), "check RF type here, need to be 8256\n");
 		NewOffset = Offset;
-	}
+
 	//put desired read addr to LSSI control Register
 	rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadAddress, NewOffset);
 	//Issue a posedge trigger
@@ -713,23 +706,18 @@ static u32 rtl8192_phy_RFSerialRead(struct net_device* dev, RF90_RADIO_PATH_E eR
 
 
 	// Switch back to Reg_Mode0;
-	if(priv->rf_chip == RF_8256)
-	{
-		priv->RfReg0Value[eRFPath] &= 0xebf;
-
-		rtl8192_setBBreg(
-			dev,
-			pPhyReg->rf3wireOffset,
-			bMaskDWord,
-			(priv->RfReg0Value[eRFPath] << 16));
+	priv->RfReg0Value[eRFPath] &= 0xebf;
 
-		//analog to digital on
-		rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
-	}
+	rtl8192_setBBreg(
+		dev,
+		pPhyReg->rf3wireOffset,
+		bMaskDWord,
+		(priv->RfReg0Value[eRFPath] << 16));
 
+	//analog to digital on
+	rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
 
 	return ret;
-
 }
 
 /******************************************************************************
@@ -759,33 +747,25 @@ static void rtl8192_phy_RFSerialWrite(struct net_device* dev, RF90_RADIO_PATH_E
 	BB_REGISTER_DEFINITION_T	*pPhyReg = &priv->PHYRegDef[eRFPath];
 
 	Offset &= 0x3f;
-	if (priv->rf_chip == RF_8256)
-	{
 
-		//analog to digital off, for protection
-		rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
+	//analog to digital off, for protection
+	rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, 0x0);// 0x88c[11:8]
 
-		if (Offset >= 31)
-		{
-			priv->RfReg0Value[eRFPath] |= 0x140;
-			rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath] << 16));
-			NewOffset = Offset - 30;
-		}
-		else if (Offset >= 16)
-		{
-			priv->RfReg0Value[eRFPath] |= 0x100;
-			priv->RfReg0Value[eRFPath] &= (~0x40);
-			rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16));
-			NewOffset = Offset - 15;
-		}
-		else
-			NewOffset = Offset;
+	if (Offset >= 31)
+	{
+		priv->RfReg0Value[eRFPath] |= 0x140;
+		rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath] << 16));
+		NewOffset = Offset - 30;
 	}
-	else
+	else if (Offset >= 16)
 	{
-		RT_TRACE((COMP_PHY|COMP_ERR), "check RF type here, need to be 8256\n");
-		NewOffset = Offset;
+		priv->RfReg0Value[eRFPath] |= 0x100;
+		priv->RfReg0Value[eRFPath] &= (~0x40);
+		rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, (priv->RfReg0Value[eRFPath]<<16));
+		NewOffset = Offset - 15;
 	}
+	else
+		NewOffset = Offset;
 
 	// Put write addr in [5:0]  and write data in [31:16]
 	DataAndAddr = (Data<<16) | (NewOffset&0x3f);
@@ -798,20 +778,17 @@ static void rtl8192_phy_RFSerialWrite(struct net_device* dev, RF90_RADIO_PATH_E
 		priv->RfReg0Value[eRFPath] = Data;
 
 	// Switch back to Reg_Mode0;
- 	if(priv->rf_chip == RF_8256)
+	if(Offset != 0)
 	{
-		if(Offset != 0)
-		{
-			priv->RfReg0Value[eRFPath] &= 0xebf;
-			rtl8192_setBBreg(
-				dev,
-				pPhyReg->rf3wireOffset,
-				bMaskDWord,
-				(priv->RfReg0Value[eRFPath] << 16));
-		}
-		//analog to digital on
-		rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
+		priv->RfReg0Value[eRFPath] &= 0xebf;
+		rtl8192_setBBreg(
+			dev,
+			pPhyReg->rf3wireOffset,
+			bMaskDWord,
+			(priv->RfReg0Value[eRFPath] << 16));
 	}
+	//analog to digital on
+	rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, 0x3);// 0x88c[9:8]
 }
 
 /******************************************************************************
@@ -1555,22 +1532,8 @@ void rtl8192_phy_setTxPower(struct net_device* dev, u8 channel)
 	pHalData->CurrentCckTxPwrIdx = powerlevel;
 	pHalData->CurrentOfdm24GTxPwrIdx = powerlevelOFDM24G;
 #endif
-	switch(priv->rf_chip)
-	{
-	case RF_8225:
-	//	PHY_SetRF8225CckTxPower(Adapter, powerlevel);
-	//	PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G);
-		break;
-	case RF_8256:
-		PHY_SetRF8256CCKTxPower(dev, powerlevel); //need further implement
-		PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
-		break;
-	case RF_8258:
-		break;
-	default:
-		RT_TRACE(COMP_ERR, "unknown rf chip in funtion %s()\n", __FUNCTION__);
-		break;
-	}
+	PHY_SetRF8256CCKTxPower(dev, powerlevel); //need further implement
+	PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
 }
 
 /******************************************************************************
@@ -1581,28 +1544,7 @@ void rtl8192_phy_setTxPower(struct net_device* dev, u8 channel)
  * ***************************************************************************/
 RT_STATUS rtl8192_phy_RFConfig(struct net_device* dev)
 {
-	struct r8192_priv *priv = ieee80211_priv(dev);
-	RT_STATUS rtStatus = RT_STATUS_SUCCESS;
-	switch(priv->rf_chip)
-	{
-		case RF_8225:
-//			rtStatus = PHY_RF8225_Config(Adapter);
-			break;
-		case RF_8256:
-			rtStatus = PHY_RF8256_Config(dev);
-			break;
-
-		case RF_8258:
-			break;
-		case RF_PSEUDO_11N:
-		//rtStatus = PHY_RF8225_Config(Adapter);
-		break;
-
-		default:
-			RT_TRACE(COMP_ERR, "error chip id\n");
-			break;
-	}
-	return rtStatus;
+	return PHY_RF8256_Config(dev);
 }
 
 /******************************************************************************
@@ -1699,27 +1641,10 @@ static void rtl8192_SetTxPowerLevel(struct net_device *dev, u8 channel)
 	u8	powerlevel = priv->TxPowerLevelCCK[channel-1];
 	u8	powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1];
 
-	switch(priv->rf_chip)
-	{
-	case RF_8225:
-#ifdef TO_DO_LIST
-		PHY_SetRF8225CckTxPower(Adapter, powerlevel);
-		PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G);
-#endif
-		break;
-
-	case RF_8256:
-		PHY_SetRF8256CCKTxPower(dev, powerlevel);
-		PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
-		break;
-
-	case RF_8258:
-		break;
-	default:
-		RT_TRACE(COMP_ERR, "unknown rf chip ID in rtl8192_SetTxPowerLevel()\n");
-		break;
-	}
+	PHY_SetRF8256CCKTxPower(dev, powerlevel);
+	PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
 }
+
 /****************************************************************************************
  *function:  This function set command table variable(struct SwChnlCmd).
  *   input:  SwChnlCmd*		CmdTable 	//table to be set.
@@ -1823,42 +1748,17 @@ static u8 rtl8192_phy_SwChnlStepByStep(struct net_device *dev, u8 channel, u8* s
 
 		// <3> Fill up RF dependent command.
 		RfDependCmdCnt = 0;
-		switch( priv->rf_chip )
-		{
-		case RF_8225:
-			if (!(channel >= 1 && channel <= 14))
-			{
-				RT_TRACE(COMP_ERR, "illegal channel for Zebra 8225: %d\n", channel);
-				return false;
-			}
-			rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
-				CmdID_RF_WriteReg, rZebra1_Channel, RF_CHANNEL_TABLE_ZEBRA[channel], 10);
-			rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
-				CmdID_End, 0, 0, 0);
-			break;
-
-		case RF_8256:
-			// TEST!! This is not the table for 8256!!
-			if (!(channel >= 1 && channel <= 14))
-			{
-				RT_TRACE(COMP_ERR, "illegal channel for Zebra 8256: %d\n", channel);
-				return false;
-			}
-			rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
-				CmdID_RF_WriteReg, rZebra1_Channel, channel, 10);
-			rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
-			CmdID_End, 0, 0, 0);
-			break;
-
-		case RF_8258:
-			break;
 
-		default:
-			RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
+		// TEST!! This is not the table for 8256!!
+		if (!(channel >= 1 && channel <= 14))
+		{
+			RT_TRACE(COMP_ERR, "illegal channel for Zebra 8256: %d\n", channel);
 			return false;
-			break;
 		}
-
+		rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
+			CmdID_RF_WriteReg, rZebra1_Channel, channel, 10);
+		rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, MAX_RFDEPENDCMD_CNT,
+		CmdID_End, 0, 0, 0);
 
 		do{
 			switch(*stage)
@@ -2149,11 +2049,6 @@ void rtl8192_SetBWModeWorkItem(struct net_device *dev)
 					priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20?"20MHz":"40MHz")
 
 
-	if(priv->rf_chip== RF_PSEUDO_11N)
-	{
-		priv->SetBWModeInProgress= false;
-		return;
-	}
 	if(!priv->up)
 	{
 		priv->SetBWModeInProgress= false;
@@ -2241,30 +2136,7 @@ void rtl8192_SetBWModeWorkItem(struct net_device *dev)
 	//Skip over setting of J-mode in BB register here. Default value is "None J mode". Emily 20070315
 
 	//<3>Set RF related register
-	switch( priv->rf_chip )
-	{
-		case RF_8225:
-#ifdef TO_DO_LIST
-			PHY_SetRF8225Bandwidth(Adapter, pHalData->CurrentChannelBW);
-#endif
-			break;
-
-		case RF_8256:
-			PHY_SetRF8256Bandwidth(dev, priv->CurrentChannelBW);
-			break;
-
-		case RF_8258:
-			// PHY_SetRF8258Bandwidth();
-			break;
-
-		case RF_PSEUDO_11N:
-			// Do Nothing
-			break;
-
-		default:
-			RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
-			break;
-	}
+	PHY_SetRF8256Bandwidth(dev, priv->CurrentChannelBW);
 
 	atomic_dec(&(priv->ieee80211->atm_swbw));
 	priv->SetBWModeInProgress= false;