wl12xx: disable AP-mode-specific quirks

The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.

WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

drivers/net/wireless/wl12xx/boot.c

@@ -770,9 +770,6 @@ int wl1271_load_firmware(struct wl1271 *wl)
 		clk |= (wl->ref_clock << 1) << 4;
 	}
 
-	if (wl->quirks & WL12XX_QUIRK_LPD_MODE)
-		clk |= SCRATCH_ENABLE_LPD;
-
 	wl1271_write32(wl, DRPW_SCRATCH_START, clk);
 
 	wl1271_set_partition(wl, &part_table[PART_WORK]);

drivers/net/wireless/wl12xx/cmd.c

@@ -134,11 +134,6 @@ int wl1271_cmd_general_parms(struct wl1271 *wl)
 	/* Override the REF CLK from the NVS with the one from platform data */
 	gen_parms->general_params.ref_clock = wl->ref_clock;
 
-	/* LPD mode enable (bits 6-7) in WL1271 AP mode only */
-	if (wl->quirks & WL12XX_QUIRK_LPD_MODE)
-		gen_parms->general_params.general_settings |=
-			GENERAL_SETTINGS_DRPW_LPD;
-
 	ret = wl1271_cmd_test(wl, gen_parms, sizeof(*gen_parms), answer);
 	if (ret < 0) {
 		wl1271_warning("CMD_INI_FILE_GENERAL_PARAM failed");

drivers/net/wireless/wl12xx/main.c

@@ -1333,14 +1333,6 @@ static int wl1271_chip_wakeup(struct wl1271 *wl)
 		wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1271 PG20)",
 			     wl->chip.id);
 
-		/*
-		 * 'end-of-transaction flag' and 'LPD mode flag'
-		 * should be set in wl127x AP mode only
-		 */
-		if (wl->bss_type == BSS_TYPE_AP_BSS)
-			wl->quirks |= (WL12XX_QUIRK_END_OF_TRANSACTION |
-				       WL12XX_QUIRK_LPD_MODE);
-
 		ret = wl1271_setup(wl);
 		if (ret < 0)
 			goto out;

drivers/net/wireless/wl12xx/wl12xx.h

@@ -672,12 +672,6 @@ size_t wl12xx_copy_fwlog(struct wl1271 *wl, u8 *memblock, size_t maxlen);
 /* WL128X requires aggregated packets to be aligned to the SDIO block size */
 #define WL12XX_QUIRK_BLOCKSIZE_ALIGNMENT	BIT(2)
 
-/*
- * WL127X AP mode requires Low Power DRPw (LPD) enable to reduce power
- * consumption
- */
-#define WL12XX_QUIRK_LPD_MODE                   BIT(3)
-
 /* Older firmwares did not implement the FW logger over bus feature */
 #define WL12XX_QUIRK_FWLOG_NOT_IMPLEMENTED	BIT(4)