Merge branches 'next/generic', 'next/alchemy', 'next/bcm63xx', 'next/cavium', 'next/jz4740', 'next/lantiq', 'next/loongson1b' and 'next/netlogic' into mips-for-linux-next

Documentation/devicetree/bindings/ata/cavium-compact-flash.txt

@@ -0,0 +1,30 @@
+* Compact Flash
+
+The Cavium Compact Flash device is connected to the Octeon Boot Bus,
+and is thus a child of the Boot Bus device.  It can read and write
+industry standard compact flash devices.
+
+Properties:
+- compatible: "cavium,ebt3000-compact-flash";
+
+  Compatibility with many Cavium evaluation boards.
+
+- reg: The base address of the the CF chip select banks.  Depending on
+  the device configuration, there may be one or two banks.
+
+- cavium,bus-width: The width of the connection to the CF devices.  Valid
+  values are 8 and 16.
+
+- cavium,true-ide: Optional, if present the CF connection is in True IDE mode.
+
+- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected
+  to this device.
+
+Example:
+	compact-flash@5,0 {
+		compatible = "cavium,ebt3000-compact-flash";
+		reg = <5 0 0x10000>, <6 0 0x10000>;
+		cavium,bus-width = <16>;
+		cavium,true-ide;
+		cavium,dma-engine-handle = <&dma0>;
+	};

Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt

@@ -0,0 +1,49 @@
+* General Purpose Input Output (GPIO) bus.
+
+Properties:
+- compatible: "cavium,octeon-3860-gpio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the GPIO unit's register bank.
+
+- gpio-controller: This is a GPIO controller.
+
+- #gpio-cells: Must be <2>.  The first cell is the GPIO pin.
+
+- interrupt-controller: The GPIO controller is also an interrupt
+  controller, many of its pins may be configured as an interrupt
+  source.
+
+- #interrupt-cells: Must be <2>.  The first cell is the GPIO pin
+   connected to the interrupt source.  The second cell is the interrupt
+   triggering protocol and may have one of four values:
+   1 - edge triggered on the rising edge.
+   2 - edge triggered on the falling edge
+   4 - level triggered active high.
+   8 - level triggered active low.
+
+- interrupts: Interrupt routing for each pin.
+
+Example:
+
+	gpio-controller@1070000000800 {
+		#gpio-cells = <2>;
+		compatible = "cavium,octeon-3860-gpio";
+		reg = <0x10700 0x00000800 0x0 0x100>;
+		gpio-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) GPIO pin number (0..15)
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		/* The GPIO pin connect to 16 consecutive CUI bits */
+		interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+			     <0 20>, <0 21>, <0 22>, <0 23>,
+			     <0 24>, <0 25>, <0 26>, <0 27>,
+			     <0 28>, <0 29>, <0 30>, <0 31>;
+	};

Documentation/devicetree/bindings/i2c/cavium-i2c.txt

@@ -0,0 +1,34 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+	twsi0: i2c@1180000001000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cavium,octeon-3860-twsi";
+		reg = <0x11800 0x00001000 0x0 0x200>;
+		interrupts = <0 45>;
+		clock-frequency = <100000>;
+
+		rtc@68 {
+			compatible = "dallas,ds1337";
+			reg = <0x68>;
+		};
+		tmp@4c {
+			compatible = "ti,tmp421";
+			reg = <0x4c>;
+		};
+	};

Documentation/devicetree/bindings/mips/cavium/bootbus.txt

@@ -0,0 +1,126 @@
+* Boot Bus
+
+The Octeon Boot Bus is a configurable parallel bus with 8 chip
+selects.  Each chip select is independently configurable.
+
+Properties:
+- compatible: "cavium,octeon-3860-bootbus"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the Boot Bus' register bank.
+
+- #address-cells: Must be <2>.  The first cell is the chip select
+   within the bootbus.  The second cell is the offset from the chip select.
+
+- #size-cells: Must be <1>.
+
+- ranges: There must be one one triplet of (child-bus-address,
+  parent-bus-address, length) for each active chip select.  If the
+  length element for any triplet is zero, the chip select is disabled,
+  making it inactive.
+
+The configuration parameters for each chip select are stored in child
+nodes.
+
+Configuration Properties:
+- compatible:  "cavium,octeon-3860-bootbus-config"
+
+- cavium,cs-index: A single cell indicating the chip select that
+  corresponds to this configuration.
+
+- cavium,t-adr: A cell specifying the ADR timing (in nS).
+
+- cavium,t-ce: A cell specifying the CE timing (in nS).
+
+- cavium,t-oe: A cell specifying the OE timing (in nS).
+
+- cavium,t-we: A cell specifying the WE timing (in nS).
+
+- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS).
+
+- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS).
+
+- cavium,t-pause: A cell specifying the PAUSE timing (in nS).
+
+- cavium,t-wait: A cell specifying the WAIT timing (in nS).
+
+- cavium,t-page: A cell specifying the PAGE timing (in nS).
+
+- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS).
+
+- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1
+  = 2 bytes, 2 = 4 bytes, 3 = 8 bytes).
+
+- cavium,wait-mode: Optional.  If present, wait mode (WAITM) is selected.
+
+- cavium,page-mode: Optional.  If present, page mode (PAGEM) is selected.
+
+- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of
+  the bus for this chip select.
+
+- cavium,ale-mode: Optional.  If present, ALE mode is selected.
+
+- cavium,sam-mode: Optional.  If present, SAM mode is selected.
+
+- cavium,or-mode: Optional.  If present, OR mode is selected.
+
+Example:
+	bootbus: bootbus@1180000000000 {
+		compatible = "cavium,octeon-3860-bootbus";
+		reg = <0x11800 0x00000000 0x0 0x200>;
+		/* The chip select number and offset */
+		#address-cells = <2>;
+		/* The size of the chip select region */
+		#size-cells = <1>;
+		ranges = <0 0  0x0 0x1f400000  0xc00000>,
+			 <1 0  0x10000 0x30000000  0>,
+			 <2 0  0x10000 0x40000000  0>,
+			 <3 0  0x10000 0x50000000  0>,
+			 <4 0  0x0 0x1d020000  0x10000>,
+			 <5 0  0x0 0x1d040000  0x10000>,
+			 <6 0  0x0 0x1d050000  0x10000>,
+			 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <0>;
+			cavium,t-adr  = <20>;
+			cavium,t-ce   = <60>;
+			cavium,t-oe   = <60>;
+			cavium,t-we   = <45>;
+			cavium,t-rd-hld = <35>;
+			cavium,t-wr-hld = <45>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <35>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,bus-width = <8>;
+		};
+		.
+		.
+		.
+		cavium,cs-config@6 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <6>;
+			cavium,t-adr  = <5>;
+			cavium,t-ce   = <300>;
+			cavium,t-oe   = <270>;
+			cavium,t-we   = <150>;
+			cavium,t-rd-hld = <100>;
+			cavium,t-wr-hld = <70>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <320>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,wait-mode;
+			cavium,bus-width = <16>;
+		};
+		.
+		.
+		.
+	};

Documentation/devicetree/bindings/mips/cavium/ciu.txt

@@ -0,0 +1,26 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-3860-ciu"
+
+  Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+   the CIU and may have a value of 0 or 1.  The second cell is the bit
+   within the bank and may have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070000000000 {
+		compatible = "cavium,octeon-3860-ciu";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0 or 1)
+		 * 2) Bit within the register (0..63)
+		 */
+		#interrupt-cells = <2>;
+		reg = <0x10700 0x00000000 0x0 0x7000>;
+	};

Documentation/devicetree/bindings/mips/cavium/ciu2.txt

@@ -0,0 +1,27 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-6880-ciu2"
+
+  Compatibility with 68XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+  the CIU and may have a value between 0 and 63.  The second cell is
+  the bit within the bank and may also have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070100000000 {
+		compatible = "cavium,octeon-6880-ciu2";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0..63)
+		 * 2) Bit within the register (0..63)
+		 */
+		#address-cells = <0>;
+		#interrupt-cells = <2>;
+		reg = <0x10701 0x00000000 0x0 0x4000000>;
+	};

Documentation/devicetree/bindings/mips/cavium/dma-engine.txt

@@ -0,0 +1,21 @@
+* DMA Engine.
+
+The Octeon DMA Engine transfers between the Boot Bus and main memory.
+The DMA Engine will be refered to by phandle by any device that is
+connected to it.
+
+Properties:
+- compatible: "cavium,octeon-5750-bootbus-dma"
+
+  Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
+
+- reg: The base address of the DMA Engine's register bank.
+
+- interrupts: A single interrupt specifier.
+
+Example:
+	dma0: dma-engine@1180000000100 {
+		compatible = "cavium,octeon-5750-bootbus-dma";
+		reg = <0x11800 0x00000100 0x0 0x8>;
+		interrupts = <0 63>;
+	};

Documentation/devicetree/bindings/mips/cavium/uctl.txt

@@ -0,0 +1,46 @@
+* UCTL USB controller glue
+
+Properties:
+- compatible: "cavium,octeon-6335-uctl"
+
+  Compatibility with all cn6XXX SOCs.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells: Must be <2>.
+
+- #size-cells: Must be <2>.
+
+- ranges: Empty to signify direct mapping of the children.
+
+- refclk-frequency: A single cell containing the reference clock
+  frequency in Hz.
+
+- refclk-type: A string describing the reference clock connection
+  either "crystal" or "external".
+
+Example:
+	uctl@118006f000000 {
+		compatible = "cavium,octeon-6335-uctl";
+		reg = <0x11800 0x6f000000 0x0 0x100>;
+		ranges; /* Direct mapping */
+		#address-cells = <2>;
+		#size-cells = <2>;
+		/* 12MHz, 24MHz and 48MHz allowed */
+		refclk-frequency = <24000000>;
+		/* Either "crystal" or "external" */
+		refclk-type = "crystal";
+
+		ehci@16f0000000000 {
+			compatible = "cavium,octeon-6335-ehci","usb-ehci";
+			reg = <0x16f00 0x00000000 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+		ohci@16f0000000400 {
+			compatible = "cavium,octeon-6335-ohci","usb-ohci";
+			reg = <0x16f00 0x00000400 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+	};

Documentation/devicetree/bindings/net/cavium-mdio.txt

@@ -0,0 +1,27 @@
+* System Management Interface (SMI) / MDIO
+
+Properties:
+- compatible: "cavium,octeon-3860-mdio"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the MDIO bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  MDIO addresses have no size component.
+
+Typically an MDIO bus might have several children.
+
+Example:
+	mdio@1180000001800 {
+		compatible = "cavium,octeon-3860-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0x00001800 0x0 0x40>;
+
+		ethernet-phy@0 {
+			...
+			reg = <0>;
+		};
+	};

Documentation/devicetree/bindings/net/cavium-mix.txt

@@ -0,0 +1,39 @@
+* MIX Ethernet controller.
+
+Properties:
+- compatible: "cavium,octeon-5750-mix"
+
+  Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX
+  devices.
+
+- reg: The base addresses of four separate register banks.  The first
+  bank contains the MIX registers.  The second bank the corresponding
+  AGL registers.  The third bank are the AGL registers shared by all
+  MIX devices present.  The fourth bank is the AGL_PRT_CTL shared by
+  all MIX devices present.
+
+- cell-index: A single cell specifying which portion of the shared
+  register banks corresponds to this MIX device.
+
+- interrupts: Two interrupt specifiers.  The first is the MIX
+  interrupt routing and the second the routing for the AGL interrupts.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+	ethernet@1070000100800 {
+		compatible = "cavium,octeon-5750-mix";
+		reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+		      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+		      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+		      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+		cell-index = <1>;
+		interrupts = <1 18>, < 1 46>;
+		local-mac-address = [ 00 0f b7 10 63 54 ];
+		phy-handle = <&phy1>;
+	};

Documentation/devicetree/bindings/net/cavium-pip.txt

@@ -0,0 +1,98 @@
+* PIP Ethernet nexus.
+
+The PIP Ethernet nexus can control several data packet input/output
+devices.  The devices have a two level grouping scheme.  There may be
+several interfaces, and each interface may have several ports.  These
+ports might be an individual Ethernet PHY.
+
+
+Properties for the PIP nexus:
+- compatible: "cavium,octeon-3860-pip"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the PIP's register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP interfaces which is a child the PIP nexus:
+- compatible: "cavium,octeon-3860-pip-interface"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The interface number.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.
+
+Properties for PIP port which is a child the PIP interface:
+- compatible: "cavium,octeon-3860-pip-port"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The port number within the interface group.
+
+- mac-address: Optional, the MAC address to assign to the device.
+
+- local-mac-address: Optional, the MAC address to assign to the device
+  if mac-address is not specified.
+
+- phy-handle: Optional, a phandle for the PHY device connected to this device.
+
+Example:
+
+	pip@11800a0000000 {
+		compatible = "cavium,octeon-3860-pip";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+		interface@0 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 60 ];
+				phy-handle = <&phy2>;
+			};
+			ethernet@1 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x1>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 61 ];
+				phy-handle = <&phy3>;
+			};
+			ethernet@2 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x2>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 62 ];
+				phy-handle = <&phy4>;
+			};
+			ethernet@3 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x3>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 63 ];
+				phy-handle = <&phy5>;
+			};
+		};
+
+		interface@1 {
+			compatible = "cavium,octeon-3860-pip-interface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>; /* interface */
+
+			ethernet@0 {
+				compatible = "cavium,octeon-3860-pip-port";
+				reg = <0x0>; /* Port */
+				local-mac-address = [ 00 0f b7 10 63 64 ];
+				phy-handle = <&phy6>;
+			};
+		};
+	};

Documentation/devicetree/bindings/serial/cavium-uart.txt

@@ -0,0 +1,19 @@
+* Universal Asynchronous Receiver/Transmitter (UART)
+
+- compatible: "cavium,octeon-3860-uart"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- current-speed: Optional, the current bit rate in bits per second.
+
+Example:
+	uart1: serial@1180000000c00 {
+		compatible = "cavium,octeon-3860-uart","ns16550";
+		reg = <0x11800 0x00000c00 0x0 0x400>;
+		current-speed = <115200>;
+		interrupts = <0 35>;
+	};

arch/mips/Kbuild.platforms

@@ -14,6 +14,7 @@ platforms += jz4740
 platforms += lantiq
 platforms += lasat
 platforms += loongson
+platforms += loongson1
 platforms += mipssim
 platforms += mti-malta
 platforms += netlogic

arch/mips/Kconfig

@@ -209,6 +209,7 @@ config MACH_JZ4740
 	select SYS_HAS_CPU_MIPS32_R1
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_ZBOOT_UART16550
 	select DMA_NONCOHERENT
 	select IRQ_CPU
 	select GENERIC_GPIO
@@ -264,6 +265,16 @@ config MACH_LOONGSON
 	  Chinese Academy of Sciences (CAS) in the People's Republic
 	  of China. The chief architect is Professor Weiwu Hu.
 
+config MACH_LOONGSON1
+	bool "Loongson 1 family of machines"
+	select SYS_SUPPORTS_ZBOOT
+	help
+	  This enables support for the Loongson 1 based machines.
+
+	  Loongson 1 is a family of 32-bit MIPS-compatible SoCs developed by
+	  the ICT (Institute of Computing Technology) and the Chinese Academy
+	  of Sciences.
+
 config MIPS_MALTA
 	bool "MIPS Malta board"
 	select ARCH_MAY_HAVE_PC_FDC
@@ -787,6 +798,8 @@ config NLM_XLR_BOARD
 	select ZONE_DMA if 64BIT
 	select SYNC_R4K
 	select SYS_HAS_EARLY_PRINTK
+	select USB_ARCH_HAS_OHCI if USB_SUPPORT
+	select USB_ARCH_HAS_EHCI if USB_SUPPORT
 	help
 	  Support for systems based on Netlogic XLR and XLS processors.
 	  Say Y here if you have a XLR or XLS based board.
@@ -799,7 +812,6 @@ config NLM_XLP_BOARD
 	select SYS_HAS_CPU_XLP
 	select SYS_SUPPORTS_SMP
 	select HW_HAS_PCI
-	select SWAP_IO_SPACE
 	select SYS_SUPPORTS_32BIT_KERNEL
 	select SYS_SUPPORTS_64BIT_KERNEL
 	select 64BIT_PHYS_ADDR
@@ -836,6 +848,7 @@ source "arch/mips/txx9/Kconfig"
 source "arch/mips/vr41xx/Kconfig"
 source "arch/mips/cavium-octeon/Kconfig"
 source "arch/mips/loongson/Kconfig"
+source "arch/mips/loongson1/Kconfig"
 source "arch/mips/netlogic/Kconfig"
 
 endmenu
@@ -1217,6 +1230,14 @@ config CPU_LOONGSON2F
 	  have a similar programming interface with FPGA northbridge used in
 	  Loongson2E.
 
+config CPU_LOONGSON1B
+	bool "Loongson 1B"
+	depends on SYS_HAS_CPU_LOONGSON1B
+	select CPU_LOONGSON1
+	help
+	  The Loongson 1B is a 32-bit SoC, which implements the MIPS32
+	  release 2 instruction set.
+
 config CPU_MIPS32_R1
 	bool "MIPS32 Release 1"
 	depends on SYS_HAS_CPU_MIPS32_R1
@@ -1432,6 +1453,8 @@ config CPU_CAVIUM_OCTEON
 	select WEAK_ORDERING
 	select CPU_SUPPORTS_HIGHMEM
 	select CPU_SUPPORTS_HUGEPAGES
+	select LIBFDT
+	select USE_OF
 	help
 	  The Cavium Octeon processor is a highly integrated chip containing
 	  many ethernet hardware widgets for networking tasks. The processor
@@ -1544,6 +1567,14 @@ config CPU_LOONGSON2
 	select CPU_SUPPORTS_64BIT_KERNEL
 	select CPU_SUPPORTS_HIGHMEM
 
+config CPU_LOONGSON1
+	bool
+	select CPU_MIPS32
+	select CPU_MIPSR2
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+
 config CPU_BMIPS
 	bool
 	select CPU_MIPS32
@@ -1562,6 +1593,9 @@ config SYS_HAS_CPU_LOONGSON2F
 	select CPU_SUPPORTS_ADDRWINCFG if 64BIT
 	select CPU_SUPPORTS_UNCACHED_ACCELERATED
 
+config SYS_HAS_CPU_LOONGSON1B
+	bool
+
 config SYS_HAS_CPU_MIPS32_R1
 	bool
 
@@ -2366,6 +2400,8 @@ config PCI_DOMAINS
 
 source "drivers/pci/Kconfig"
 
+source "drivers/pci/pcie/Kconfig"
+
 #
 # ISA support is now enabled via select.  Too many systems still have the one
 # or other ISA chip on the board that users don't know about so don't expect

arch/mips/alchemy/board-mtx1.c

@@ -81,10 +81,10 @@ static void mtx1_power_off(void)
 
 void __init board_setup(void)
 {
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
 	/* Enable USB power switch */
 	alchemy_gpio_direction_output(204, 0);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */
 
 	/* Initialize sys_pinfunc */
 	au_writel(SYS_PF_NI2, SYS_PINFUNC);

arch/mips/alchemy/common/platform.c

@@ -334,13 +334,12 @@ static void __init alchemy_setup_macs(int ctype)
 	if (alchemy_get_macs(ctype) < 1)
 		return;
 
-	macres = kmalloc(sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
+	macres = kmemdup(au1xxx_eth0_resources[ctype],
+			 sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
 	if (!macres) {
 		printk(KERN_INFO "Alchemy: no memory for MAC0 resources\n");
 		return;
 	}
-	memcpy(macres, au1xxx_eth0_resources[ctype],
-	       sizeof(struct resource) * MAC_RES_COUNT);
 	au1xxx_eth0_device.resource = macres;
 
 	i = prom_get_ethernet_addr(ethaddr);
@@ -356,13 +355,12 @@ static void __init alchemy_setup_macs(int ctype)
 	if (alchemy_get_macs(ctype) < 2)
 		return;
 
-	macres = kmalloc(sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
+	macres = kmemdup(au1xxx_eth1_resources[ctype],
+			 sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
 	if (!macres) {
 		printk(KERN_INFO "Alchemy: no memory for MAC1 resources\n");
 		return;
 	}
-	memcpy(macres, au1xxx_eth1_resources[ctype],
-	       sizeof(struct resource) * MAC_RES_COUNT);
 	au1xxx_eth1_device.resource = macres;
 
 	ethaddr[5] += 1;	/* next addr for 2nd MAC */

arch/mips/alchemy/devboards/Makefile

@@ -2,7 +2,7 @@
 # Alchemy Develboards
 #
 
-obj-y += prom.o bcsr.o platform.o
+obj-y += bcsr.o platform.o
 obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_MIPS_PB1100)	+= pb1100.o
 obj-$(CONFIG_MIPS_PB1500)	+= pb1500.o

arch/mips/alchemy/devboards/bcsr.c

@@ -90,10 +90,7 @@ static void bcsr_csc_handler(unsigned int irq, struct irq_desc *d)
 	unsigned short bisr = __raw_readw(bcsr_virt + BCSR_REG_INTSTAT);
 
 	disable_irq_nosync(irq);
-
-	for ( ; bisr; bisr &= bisr - 1)
-		generic_handle_irq(bcsr_csc_base + __ffs(bisr));
-
+	generic_handle_irq(bcsr_csc_base + __ffs(bisr));
 	enable_irq(irq);
 }
 

arch/mips/alchemy/devboards/pb1100.c

@@ -46,7 +46,7 @@ void __init board_setup(void)
 	alchemy_gpio1_input_enable();
 	udelay(100);
 
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
 	{
 		u32 pin_func, sys_freqctrl, sys_clksrc;
 
@@ -93,7 +93,7 @@ void __init board_setup(void)
 		pin_func |= SYS_PF_USB;
 		au_writel(pin_func, SYS_PINFUNC);
 	}
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */
 
 	/* Enable sys bus clock divider when IDLE state or no bus activity. */
 	au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);

arch/mips/alchemy/devboards/pb1500.c

@@ -53,7 +53,7 @@ void __init board_setup(void)
 	alchemy_gpio_direction_input(201);
 	alchemy_gpio_direction_input(203);
 
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
 
 	/* Zero and disable FREQ2 */
 	sys_freqctrl = au_readl(SYS_FREQCTRL0);
@@ -87,7 +87,7 @@ void __init board_setup(void)
 	/* 2nd USB port is USB host */
 	pin_func |= SYS_PF_USB;
 	au_writel(pin_func, SYS_PINFUNC);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */
 
 #ifdef CONFIG_PCI
 	{

arch/mips/alchemy/devboards/platform.c

@@ -10,9 +10,39 @@
 #include <linux/platform_device.h>
 #include <linux/pm.h>
 
+#include <asm/bootinfo.h>
 #include <asm/reboot.h>
+#include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-db1x00/bcsr.h>
 
+#include <prom.h>
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = (int)fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
+
+	prom_init_cmdline();
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str || kstrtoul(memsize_str, 0, &memsize))
+		memsize = 64 << 20; /* all devboards have at least 64MB RAM */
+
+	add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
+void prom_putchar(unsigned char c)
+{
+#ifdef CONFIG_MIPS_DB1300
+	alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+#else
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+#endif
+}
+
 
 static struct platform_device db1x00_rtc_dev = {
 	.name	= "rtc-au1xxx",

arch/mips/alchemy/devboards/prom.c

@@ -1,69 +0,0 @@
-/*
- * Common code used by all Alchemy develboards.
- *
- * Extracted from files which had this to say:
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <prom.h>
-
-#if defined(CONFIG_MIPS_DB1000) || \
-    defined(CONFIG_MIPS_PB1100) || \
-    defined(CONFIG_MIPS_PB1500)
-#define ALCHEMY_BOARD_DEFAULT_MEMSIZE	0x04000000
-
-#else	/* Au1550/Au1200-based develboards */
-#define ALCHEMY_BOARD_DEFAULT_MEMSIZE	0x08000000
-#endif
-
-void __init prom_init(void)
-{
-	unsigned char *memsize_str;
-	unsigned long memsize;
-
-	prom_argc = (int)fw_arg0;
-	prom_argv = (char **)fw_arg1;
-	prom_envp = (char **)fw_arg2;
-
-	prom_init_cmdline();
-	memsize_str = prom_getenv("memsize");
-	if (!memsize_str || strict_strtoul(memsize_str, 0, &memsize))
-		memsize = ALCHEMY_BOARD_DEFAULT_MEMSIZE;
-
-	add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void prom_putchar(unsigned char c)
-{
-#ifdef CONFIG_MIPS_DB1300
-	alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
-#else
-	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
-#endif
-}

arch/mips/bcm63xx/Kconfig

@@ -1,6 +1,10 @@
 menu "CPU support"
 	depends on BCM63XX
 
+config BCM63XX_CPU_6328
+	bool "support 6328 CPU"
+	select HW_HAS_PCI
+
 config BCM63XX_CPU_6338
 	bool "support 6338 CPU"
 	select HW_HAS_PCI

arch/mips/bcm63xx/Makefile

@@ -1,5 +1,6 @@
 obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-		   dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o
+		   dev-dsp.o dev-enet.o dev-flash.o dev-pcmcia.o dev-rng.o \
+		   dev-spi.o dev-uart.o dev-wdt.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 obj-y		+= boards/

arch/mips/bcm63xx/boards/board_bcm963xx.c

@@ -11,9 +11,6 @@
 #include <linux/kernel.h>
 #include <linux/string.h>
 #include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
 #include <linux/ssb/ssb.h>
 #include <asm/addrspace.h>
 #include <bcm63xx_board.h>
@@ -24,7 +21,9 @@
 #include <bcm63xx_dev_pci.h>
 #include <bcm63xx_dev_enet.h>
 #include <bcm63xx_dev_dsp.h>
+#include <bcm63xx_dev_flash.h>
 #include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_dev_spi.h>
 #include <board_bcm963xx.h>
 
 #define PFX	"board_bcm963xx: "
@@ -33,6 +32,48 @@ static struct bcm963xx_nvram nvram;
 static unsigned int mac_addr_used;
 static struct board_info board;
 
+/*
+ * known 6328 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6328
+static struct board_info __initdata board_96328avng = {
+	.name				= "96328avng",
+	.expected_cpu_id		= 0x6328,
+
+	.has_uart0			= 1,
+	.has_pci			= 1,
+
+	.leds = {
+		{
+			.name		= "96328avng::ppp-fail",
+			.gpio		= 2,
+			.active_low	= 1,
+		},
+		{
+			.name		= "96328avng::power",
+			.gpio		= 4,
+			.active_low	= 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name		= "96328avng::power-fail",
+			.gpio		= 8,
+			.active_low	= 1,
+		},
+		{
+			.name		= "96328avng::wps",
+			.gpio		= 9,
+			.active_low	= 1,
+		},
+		{
+			.name		= "96328avng::ppp",
+			.gpio		= 11,
+			.active_low	= 1,
+		},
+	},
+};
+#endif
+
 /*
  * known 6338 boards
  */
@@ -592,6 +633,9 @@ static struct board_info __initdata board_DWVS0 = {
  * all boards
  */
 static const struct board_info __initdata *bcm963xx_boards[] = {
+#ifdef CONFIG_BCM63XX_CPU_6328
+	&board_96328avng,
+#endif
 #ifdef CONFIG_BCM63XX_CPU_6338
 	&board_96338gw,
 	&board_96338w,
@@ -709,9 +753,15 @@ void __init board_prom_init(void)
 	char cfe_version[32];
 	u32 val;
 
-	/* read base address of boot chip select (0) */
-	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-	val &= MPI_CSBASE_BASE_MASK;
+	/* read base address of boot chip select (0)
+	 * 6328 does not have MPI but boots from a fixed address
+	 */
+	if (BCMCPU_IS_6328())
+		val = 0x18000000;
+	else {
+		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+		val &= MPI_CSBASE_BASE_MASK;
+	}
 	boot_addr = (u8 *)KSEG1ADDR(val);
 
 	/* dump cfe version */
@@ -808,40 +858,6 @@ void __init board_setup(void)
 		panic("unexpected CPU for bcm963xx board");
 }
 
-static struct mtd_partition mtd_partitions[] = {
-	{
-		.name		= "cfe",
-		.offset		= 0x0,
-		.size		= 0x40000,
-	}
-};
-
-static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL };
-
-static struct physmap_flash_data flash_data = {
-	.width			= 2,
-	.nr_parts		= ARRAY_SIZE(mtd_partitions),
-	.parts			= mtd_partitions,
-	.part_probe_types	= bcm63xx_part_types,
-};
-
-static struct resource mtd_resources[] = {
-	{
-		.start		= 0,	/* filled at runtime */
-		.end		= 0,	/* filled at runtime */
-		.flags		= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device mtd_dev = {
-	.name			= "physmap-flash",
-	.resource		= mtd_resources,
-	.num_resources		= ARRAY_SIZE(mtd_resources),
-	.dev			= {
-		.platform_data	= &flash_data,
-	},
-};
-
 static struct gpio_led_platform_data bcm63xx_led_data;
 
 static struct platform_device bcm63xx_gpio_leds = {
@@ -855,8 +871,6 @@ static struct platform_device bcm63xx_gpio_leds = {
  */
 int __init board_register_devices(void)
 {
-	u32 val;
-
 	if (board.has_uart0)
 		bcm63xx_uart_register(0);
 
@@ -890,14 +904,9 @@ int __init board_register_devices(void)
 	}
 #endif
 
-	/* read base address of boot chip select (0) */
-	val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-	val &= MPI_CSBASE_BASE_MASK;
-
-	mtd_resources[0].start = val;
-	mtd_resources[0].end = 0x1FFFFFFF;
+	bcm63xx_spi_register();
 
-	platform_device_register(&mtd_dev);
+	bcm63xx_flash_register();
 
 	bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
 	bcm63xx_led_data.leds = board.leds;

arch/mips/bcm63xx/clk.c

@@ -120,7 +120,7 @@ static void enetsw_set(struct clk *clk, int enable)
 {
 	if (!BCMCPU_IS_6368())
 		return;
-	bcm_hwclock_set(CKCTL_6368_ROBOSW_CLK_EN |
+	bcm_hwclock_set(CKCTL_6368_ROBOSW_EN |
 			CKCTL_6368_SWPKT_USB_EN |
 			CKCTL_6368_SWPKT_SAR_EN, enable);
 	if (enable) {
@@ -163,7 +163,7 @@ static void usbh_set(struct clk *clk, int enable)
 	if (BCMCPU_IS_6348())
 		bcm_hwclock_set(CKCTL_6348_USBH_EN, enable);
 	else if (BCMCPU_IS_6368())
-		bcm_hwclock_set(CKCTL_6368_USBH_CLK_EN, enable);
+		bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
 }
 
 static struct clk clk_usbh = {
@@ -181,9 +181,11 @@ static void spi_set(struct clk *clk, int enable)
 		mask = CKCTL_6338_SPI_EN;
 	else if (BCMCPU_IS_6348())
 		mask = CKCTL_6348_SPI_EN;
-	else
-		/* BCMCPU_IS_6358 */
+	else if (BCMCPU_IS_6358())
 		mask = CKCTL_6358_SPI_EN;
+	else
+		/* BCMCPU_IS_6368 */
+		mask = CKCTL_6368_SPI_EN;
 	bcm_hwclock_set(mask, enable);
 }
 
@@ -199,7 +201,7 @@ static void xtm_set(struct clk *clk, int enable)
 	if (!BCMCPU_IS_6368())
 		return;
 
-	bcm_hwclock_set(CKCTL_6368_SAR_CLK_EN |
+	bcm_hwclock_set(CKCTL_6368_SAR_EN |
 			CKCTL_6368_SWPKT_SAR_EN, enable);
 
 	if (enable) {
@@ -221,6 +223,18 @@ static struct clk clk_xtm = {
 	.set	= xtm_set,
 };
 
+/*
+ * IPsec clock
+ */
+static void ipsec_set(struct clk *clk, int enable)
+{
+	bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable);
+}
+
+static struct clk clk_ipsec = {
+	.set	= ipsec_set,
+};
+
 /*
  * Internal peripheral clock
  */
@@ -278,6 +292,8 @@ struct clk *clk_get(struct device *dev, const char *id)
 		return &clk_periph;
 	if (BCMCPU_IS_6358() && !strcmp(id, "pcm"))
 		return &clk_pcm;
+	if (BCMCPU_IS_6368() && !strcmp(id, "ipsec"))
+		return &clk_ipsec;
 	return ERR_PTR(-ENOENT);
 }
 

arch/mips/bcm63xx/cpu.c

@@ -29,6 +29,14 @@ static u16 bcm63xx_cpu_rev;
 static unsigned int bcm63xx_cpu_freq;
 static unsigned int bcm63xx_memory_size;
 
+static const unsigned long bcm6328_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6328)
+};
+
+static const int bcm6328_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6328)
+};
+
 static const unsigned long bcm6338_regs_base[] = {
 	__GEN_CPU_REGS_TABLE(6338)
 };
@@ -99,6 +107,33 @@ unsigned int bcm63xx_get_memory_size(void)
 static unsigned int detect_cpu_clock(void)
 {
 	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+	{
+		unsigned int tmp, mips_pll_fcvo;
+
+		tmp = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
+		mips_pll_fcvo = (tmp & STRAPBUS_6328_FCVO_MASK)
+				>> STRAPBUS_6328_FCVO_SHIFT;
+
+		switch (mips_pll_fcvo) {
+		case 0x12:
+		case 0x14:
+		case 0x19:
+			return 160000000;
+		case 0x1c:
+			return 192000000;
+		case 0x13:
+		case 0x15:
+			return 200000000;
+		case 0x1a:
+			return 384000000;
+		case 0x16:
+			return 400000000;
+		default:
+			return 320000000;
+		}
+
+	}
 	case BCM6338_CPU_ID:
 		/* BCM6338 has a fixed 240 Mhz frequency */
 		return 240000000;
@@ -170,6 +205,9 @@ static unsigned int detect_memory_size(void)
 	unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
 	u32 val;
 
+	if (BCMCPU_IS_6328())
+		return bcm_ddr_readl(DDR_CSEND_REG) << 24;
+
 	if (BCMCPU_IS_6345()) {
 		val = bcm_sdram_readl(SDRAM_MBASE_REG);
 		return (val * 8 * 1024 * 1024);
@@ -228,17 +266,26 @@ void __init bcm63xx_cpu_init(void)
 		bcm63xx_irqs = bcm6345_irqs;
 		break;
 	case CPU_BMIPS4350:
-		switch (read_c0_prid() & 0xf0) {
-		case 0x10:
+		if ((read_c0_prid() & 0xf0) == 0x10) {
 			expected_cpu_id = BCM6358_CPU_ID;
 			bcm63xx_regs_base = bcm6358_regs_base;
 			bcm63xx_irqs = bcm6358_irqs;
-			break;
-		case 0x30:
-			expected_cpu_id = BCM6368_CPU_ID;
-			bcm63xx_regs_base = bcm6368_regs_base;
-			bcm63xx_irqs = bcm6368_irqs;
-			break;
+		} else {
+			/* all newer chips have the same chip id location */
+			u16 chip_id = bcm_readw(BCM_6368_PERF_BASE);
+
+			switch (chip_id) {
+			case BCM6328_CPU_ID:
+				expected_cpu_id = BCM6328_CPU_ID;
+				bcm63xx_regs_base = bcm6328_regs_base;
+				bcm63xx_irqs = bcm6328_irqs;
+				break;
+			case BCM6368_CPU_ID:
+				expected_cpu_id = BCM6368_CPU_ID;
+				bcm63xx_regs_base = bcm6368_regs_base;
+				bcm63xx_irqs = bcm6368_irqs;
+				break;
+			}
 		}
 		break;
 	}

arch/mips/bcm63xx/dev-dsp.c

@@ -31,7 +31,7 @@ static struct resource voip_dsp_resources[] = {
 
 static struct platform_device bcm63xx_voip_dsp_device = {
 	.name		= "bcm63xx-voip-dsp",
-	.id		= 0,
+	.id		= -1,
 	.num_resources	= ARRAY_SIZE(voip_dsp_resources),
 	.resource	= voip_dsp_resources,
 };

arch/mips/bcm63xx/dev-flash.c

@@ -0,0 +1,123 @@
+/*
+ * Broadcom BCM63xx flash registration
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_flash.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+
+static struct mtd_partition mtd_partitions[] = {
+	{
+		.name		= "cfe",
+		.offset		= 0x0,
+		.size		= 0x40000,
+	}
+};
+
+static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL };
+
+static struct physmap_flash_data flash_data = {
+	.width			= 2,
+	.parts			= mtd_partitions,
+	.part_probe_types	= bcm63xx_part_types,
+};
+
+static struct resource mtd_resources[] = {
+	{
+		.start		= 0,	/* filled at runtime */
+		.end		= 0,	/* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device mtd_dev = {
+	.name			= "physmap-flash",
+	.resource		= mtd_resources,
+	.num_resources		= ARRAY_SIZE(mtd_resources),
+	.dev			= {
+		.platform_data	= &flash_data,
+	},
+};
+
+static int __init bcm63xx_detect_flash_type(void)
+{
+	u32 val;
+
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		val = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
+		if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		else
+			return BCM63XX_FLASH_TYPE_NAND;
+	case BCM6338_CPU_ID:
+	case BCM6345_CPU_ID:
+	case BCM6348_CPU_ID:
+		/* no way to auto detect so assume parallel */
+		return BCM63XX_FLASH_TYPE_PARALLEL;
+	case BCM6358_CPU_ID:
+		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+		if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
+			return BCM63XX_FLASH_TYPE_PARALLEL;
+		else
+			return BCM63XX_FLASH_TYPE_SERIAL;
+	case BCM6368_CPU_ID:
+		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+		switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
+		case STRAPBUS_6368_BOOT_SEL_NAND:
+			return BCM63XX_FLASH_TYPE_NAND;
+		case STRAPBUS_6368_BOOT_SEL_SERIAL:
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		case STRAPBUS_6368_BOOT_SEL_PARALLEL:
+			return BCM63XX_FLASH_TYPE_PARALLEL;
+		}
+	default:
+		return -EINVAL;
+	}
+}
+
+int __init bcm63xx_flash_register(void)
+{
+	int flash_type;
+	u32 val;
+
+	flash_type = bcm63xx_detect_flash_type();
+
+	switch (flash_type) {
+	case BCM63XX_FLASH_TYPE_PARALLEL:
+		/* read base address of boot chip select (0) */
+		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+		val &= MPI_CSBASE_BASE_MASK;
+
+		mtd_resources[0].start = val;
+		mtd_resources[0].end = 0x1FFFFFFF;
+
+		return platform_device_register(&mtd_dev);
+	case BCM63XX_FLASH_TYPE_SERIAL:
+		pr_warn("unsupported serial flash detected\n");
+		return -ENODEV;
+	case BCM63XX_FLASH_TYPE_NAND:
+		pr_warn("unsupported NAND flash detected\n");
+		return -ENODEV;
+	default:
+		pr_err("flash detection failed for BCM%x: %d\n",
+		       bcm63xx_get_cpu_id(), flash_type);
+		return -ENODEV;
+	}
+}

arch/mips/bcm63xx/dev-rng.c

@@ -0,0 +1,40 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+
+static struct resource rng_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bcm63xx_rng_device = {
+	.name		= "bcm63xx-rng",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(rng_resources),
+	.resource	= rng_resources,
+};
+
+int __init bcm63xx_rng_register(void)
+{
+	if (!BCMCPU_IS_6368())
+		return -ENODEV;
+
+	rng_resources[0].start = bcm63xx_regset_address(RSET_RNG);
+	rng_resources[0].end = rng_resources[0].start;
+	rng_resources[0].end += RSET_RNG_SIZE - 1;
+
+	return platform_device_register(&bcm63xx_rng_device);
+}
+arch_initcall(bcm63xx_rng_register);

arch/mips/bcm63xx/dev-spi.c

@@ -0,0 +1,119 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2009-2011 Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_spi.h>
+#include <bcm63xx_regs.h>
+
+#ifdef BCMCPU_RUNTIME_DETECT
+/*
+ * register offsets
+ */
+static const unsigned long bcm6338_regs_spi[] = {
+	__GEN_SPI_REGS_TABLE(6338)
+};
+
+static const unsigned long bcm6348_regs_spi[] = {
+	__GEN_SPI_REGS_TABLE(6348)
+};
+
+static const unsigned long bcm6358_regs_spi[] = {
+	__GEN_SPI_REGS_TABLE(6358)
+};
+
+static const unsigned long bcm6368_regs_spi[] = {
+	__GEN_SPI_REGS_TABLE(6368)
+};
+
+const unsigned long *bcm63xx_regs_spi;
+EXPORT_SYMBOL(bcm63xx_regs_spi);
+
+static __init void bcm63xx_spi_regs_init(void)
+{
+	if (BCMCPU_IS_6338())
+		bcm63xx_regs_spi = bcm6338_regs_spi;
+	if (BCMCPU_IS_6348())
+		bcm63xx_regs_spi = bcm6348_regs_spi;
+	if (BCMCPU_IS_6358())
+		bcm63xx_regs_spi = bcm6358_regs_spi;
+	if (BCMCPU_IS_6368())
+		bcm63xx_regs_spi = bcm6368_regs_spi;
+}
+#else
+static __init void bcm63xx_spi_regs_init(void) { }
+#endif
+
+static struct resource spi_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct bcm63xx_spi_pdata spi_pdata = {
+	.bus_num		= 0,
+	.num_chipselect		= 8,
+};
+
+static struct platform_device bcm63xx_spi_device = {
+	.name		= "bcm63xx-spi",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(spi_resources),
+	.resource	= spi_resources,
+	.dev		= {
+		.platform_data = &spi_pdata,
+	},
+};
+
+int __init bcm63xx_spi_register(void)
+{
+	struct clk *periph_clk;
+
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6345())
+		return -ENODEV;
+
+	periph_clk = clk_get(NULL, "periph");
+	if (IS_ERR(periph_clk)) {
+		pr_err("unable to get periph clock\n");
+		return -ENODEV;
+	}
+
+	/* Set bus frequency */
+	spi_pdata.speed_hz = clk_get_rate(periph_clk);
+
+	spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
+	spi_resources[0].end = spi_resources[0].start;
+	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
+
+	if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
+		spi_resources[0].end += BCM_6338_RSET_SPI_SIZE - 1;
+		spi_pdata.fifo_size = SPI_6338_MSG_DATA_SIZE;
+	}
+
+	if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
+		spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
+		spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
+	}
+
+	bcm63xx_spi_regs_init();
+
+	return platform_device_register(&bcm63xx_spi_device);
+}

arch/mips/bcm63xx/dev-wdt.c

@@ -21,7 +21,7 @@ static struct resource wdt_resources[] = {
 
 static struct platform_device bcm63xx_wdt_device = {
 	.name		= "bcm63xx-wdt",
-	.id		= 0,
+	.id		= -1,
 	.num_resources	= ARRAY_SIZE(wdt_resources),
 	.resource	= wdt_resources,
 };

arch/mips/bcm63xx/irq.c

@@ -27,6 +27,17 @@ static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused;
 static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused;
 
 #ifndef BCMCPU_RUNTIME_DETECT
+#ifdef CONFIG_BCM63XX_CPU_6328
+#define irq_stat_reg		PERF_IRQSTAT_6328_REG
+#define irq_mask_reg		PERF_IRQMASK_6328_REG
+#define irq_bits		64
+#define is_ext_irq_cascaded	1
+#define ext_irq_start		(BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE)
+#define ext_irq_end		(BCM_6328_EXT_IRQ3 - IRQ_INTERNAL_BASE)
+#define ext_irq_count		4
+#define ext_irq_cfg_reg1	PERF_EXTIRQ_CFG_REG_6328
+#define ext_irq_cfg_reg2	0
+#endif
 #ifdef CONFIG_BCM63XX_CPU_6338
 #define irq_stat_reg		PERF_IRQSTAT_6338_REG
 #define irq_mask_reg		PERF_IRQMASK_6338_REG
@@ -118,6 +129,16 @@ static void bcm63xx_init_irq(void)
 	irq_mask_addr = bcm63xx_regset_address(RSET_PERF);
 
 	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		irq_stat_addr += PERF_IRQSTAT_6328_REG;
+		irq_mask_addr += PERF_IRQMASK_6328_REG;
+		irq_bits = 64;
+		ext_irq_count = 4;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6328_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6328;
+		break;
 	case BCM6338_CPU_ID:
 		irq_stat_addr += PERF_IRQSTAT_6338_REG;
 		irq_mask_addr += PERF_IRQMASK_6338_REG;

arch/mips/bcm63xx/prom.c

@@ -26,7 +26,9 @@ void __init prom_init(void)
 	bcm_wdt_writel(WDT_STOP_2, WDT_CTL_REG);
 
 	/* disable all hardware blocks clock for now */
-	if (BCMCPU_IS_6338())
+	if (BCMCPU_IS_6328())
+		mask = CKCTL_6328_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6338())
 		mask = CKCTL_6338_ALL_SAFE_EN;
 	else if (BCMCPU_IS_6345())
 		mask = CKCTL_6345_ALL_SAFE_EN;

arch/mips/bcm63xx/setup.c

@@ -68,6 +68,9 @@ void bcm63xx_machine_reboot(void)
 
 	/* mask and clear all external irq */
 	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328;
+		break;
 	case BCM6338_CPU_ID:
 		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6338;
 		break;
@@ -95,9 +98,13 @@ void bcm63xx_machine_reboot(void)
 		bcm6348_a1_reboot();
 
 	printk(KERN_INFO "triggering watchdog soft-reset...\n");
-	reg = bcm_perf_readl(PERF_SYS_PLL_CTL_REG);
-	reg |= SYS_PLL_SOFT_RESET;
-	bcm_perf_writel(reg, PERF_SYS_PLL_CTL_REG);
+	if (BCMCPU_IS_6328()) {
+		bcm_wdt_writel(1, WDT_SOFTRESET_REG);
+	} else {
+		reg = bcm_perf_readl(PERF_SYS_PLL_CTL_REG);
+		reg |= SYS_PLL_SOFT_RESET;
+		bcm_perf_writel(reg, PERF_SYS_PLL_CTL_REG);
+	}
 	while (1)
 		;
 }

arch/mips/boot/compressed/Makefile

@@ -58,8 +58,12 @@ $(obj)/piggy.o: $(obj)/dummy.o $(obj)/vmlinux.bin.z FORCE
 # Calculate the load address of the compressed kernel image
 hostprogs-y := calc_vmlinuz_load_addr
 
+ifeq ($(CONFIG_MACH_JZ4740),y)
+VMLINUZ_LOAD_ADDRESS := 0x80600000
+else
 VMLINUZ_LOAD_ADDRESS = $(shell $(obj)/calc_vmlinuz_load_addr \
 		$(obj)/vmlinux.bin $(VMLINUX_LOAD_ADDRESS))
+endif
 
 vmlinuzobjs-y += $(obj)/piggy.o
 

arch/mips/boot/compressed/uart-16550.c

@@ -18,6 +18,11 @@
 #define PORT(offset) (CKSEG1ADDR(AR7_REGS_UART0) + (4 * offset))
 #endif
 
+#ifdef CONFIG_MACH_JZ4740
+#define UART0_BASE  0xB0030000
+#define PORT(offset) (UART0_BASE + (4 * offset))
+#endif
+
 #ifndef PORT
 #error please define the serial port address for your own machine
 #endif

arch/mips/cavium-octeon/.gitignore

@@ -0,0 +1,2 @@
+*.dtb.S
+*.dtb

arch/mips/cavium-octeon/Makefile

@@ -9,9 +9,25 @@
 # Copyright (C) 2005-2009 Cavium Networks
 #
 
+CFLAGS_octeon-platform.o = -I$(src)/../../../scripts/dtc/libfdt
+CFLAGS_setup.o = -I$(src)/../../../scripts/dtc/libfdt
+
 obj-y := cpu.o setup.o serial.o octeon-platform.o octeon-irq.o csrc-octeon.o
 obj-y += dma-octeon.o flash_setup.o
 obj-y += octeon-memcpy.o
 obj-y += executive/
 
 obj-$(CONFIG_SMP)                     += smp.o
+
+DTS_FILES = octeon_3xxx.dts octeon_68xx.dts
+DTB_FILES = $(patsubst %.dts, %.dtb, $(DTS_FILES))
+
+obj-y += $(patsubst %.dts, %.dtb.o, $(DTS_FILES))
+
+$(obj)/%.dtb: $(src)/%.dts FORCE
+	$(call if_changed_dep,dtc)
+
+# Let's keep the .dtb files around in case we want to look at them.
+.SECONDARY:  $(addprefix $(obj)/, $(DTB_FILES))
+
+clean-files += $(DTB_FILES) $(patsubst %.dtb, %.dtb.S, $(DTB_FILES))

arch/mips/cavium-octeon/executive/cvmx-fpa.c

@@ -1,183 +0,0 @@
-/***********************license start***************
- * Author: Cavium Networks
- *
- * Contact: support@caviumnetworks.com
- * This file is part of the OCTEON SDK
- *
- * Copyright (c) 2003-2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful, but
- * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
- * NONINFRINGEMENT.  See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this file; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- * or visit http://www.gnu.org/licenses/.
- *
- * This file may also be available under a different license from Cavium.
- * Contact Cavium Networks for more information
- ***********************license end**************************************/
-
-/**
- * @file
- *
- * Support library for the hardware Free Pool Allocator.
- *
- *
- */
-
-#include "cvmx-config.h"
-#include "cvmx.h"
-#include "cvmx-fpa.h"
-#include "cvmx-ipd.h"
-
-/**
- * Current state of all the pools. Use access functions
- * instead of using it directly.
- */
-CVMX_SHARED cvmx_fpa_pool_info_t cvmx_fpa_pool_info[CVMX_FPA_NUM_POOLS];
-
-/**
- * Setup a FPA pool to control a new block of memory. The
- * buffer pointer must be a physical address.
- *
- * @pool:       Pool to initialize
- *                   0 <= pool < 8
- * @name:       Constant character string to name this pool.
- *                   String is not copied.
- * @buffer:     Pointer to the block of memory to use. This must be
- *                   accessible by all processors and external hardware.
- * @block_size: Size for each block controlled by the FPA
- * @num_blocks: Number of blocks
- *
- * Returns 0 on Success,
- *         -1 on failure
- */
-int cvmx_fpa_setup_pool(uint64_t pool, const char *name, void *buffer,
-			uint64_t block_size, uint64_t num_blocks)
-{
-	char *ptr;
-	if (!buffer) {
-		cvmx_dprintf
-		    ("ERROR: cvmx_fpa_setup_pool: NULL buffer pointer!\n");
-		return -1;
-	}
-	if (pool >= CVMX_FPA_NUM_POOLS) {
-		cvmx_dprintf("ERROR: cvmx_fpa_setup_pool: Illegal pool!\n");
-		return -1;
-	}
-
-	if (block_size < CVMX_FPA_MIN_BLOCK_SIZE) {
-		cvmx_dprintf
-		    ("ERROR: cvmx_fpa_setup_pool: Block size too small.\n");
-		return -1;
-	}
-
-	if (((unsigned long)buffer & (CVMX_FPA_ALIGNMENT - 1)) != 0) {
-		cvmx_dprintf
-		    ("ERROR: cvmx_fpa_setup_pool: Buffer not aligned properly.\n");
-		return -1;
-	}
-
-	cvmx_fpa_pool_info[pool].name = name;
-	cvmx_fpa_pool_info[pool].size = block_size;
-	cvmx_fpa_pool_info[pool].starting_element_count = num_blocks;
-	cvmx_fpa_pool_info[pool].base = buffer;
-
-	ptr = (char *)buffer;
-	while (num_blocks--) {
-		cvmx_fpa_free(ptr, pool, 0);
-		ptr += block_size;
-	}
-	return 0;
-}
-
-/**
- * Shutdown a Memory pool and validate that it had all of
- * the buffers originally placed in it.
- *
- * @pool:   Pool to shutdown
- * Returns Zero on success
- *         - Positive is count of missing buffers
- *         - Negative is too many buffers or corrupted pointers
- */
-uint64_t cvmx_fpa_shutdown_pool(uint64_t pool)
-{
-	uint64_t errors = 0;
-	uint64_t count = 0;
-	uint64_t base = cvmx_ptr_to_phys(cvmx_fpa_pool_info[pool].base);
-	uint64_t finish =
-	    base +
-	    cvmx_fpa_pool_info[pool].size *
-	    cvmx_fpa_pool_info[pool].starting_element_count;
-	void *ptr;
-	uint64_t address;
-
-	count = 0;
-	do {
-		ptr = cvmx_fpa_alloc(pool);
-		if (ptr)
-			address = cvmx_ptr_to_phys(ptr);
-		else
-			address = 0;
-		if (address) {
-			if ((address >= base) && (address < finish) &&
-			    (((address -
-			       base) % cvmx_fpa_pool_info[pool].size) == 0)) {
-				count++;
-			} else {
-				cvmx_dprintf
-				    ("ERROR: cvmx_fpa_shutdown_pool: Illegal address 0x%llx in pool %s(%d)\n",
-				     (unsigned long long)address,
-				     cvmx_fpa_pool_info[pool].name, (int)pool);
-				errors++;
-			}
-		}
-	} while (address);
-
-#ifdef CVMX_ENABLE_PKO_FUNCTIONS
-	if (pool == 0)
-		cvmx_ipd_free_ptr();
-#endif
-
-	if (errors) {
-		cvmx_dprintf
-		    ("ERROR: cvmx_fpa_shutdown_pool: Pool %s(%d) started at 0x%llx, ended at 0x%llx, with a step of 0x%llx\n",
-		     cvmx_fpa_pool_info[pool].name, (int)pool,
-		     (unsigned long long)base, (unsigned long long)finish,
-		     (unsigned long long)cvmx_fpa_pool_info[pool].size);
-		return -errors;
-	} else
-		return 0;
-}
-
-uint64_t cvmx_fpa_get_block_size(uint64_t pool)
-{
-	switch (pool) {
-	case 0:
-		return CVMX_FPA_POOL_0_SIZE;
-	case 1:
-		return CVMX_FPA_POOL_1_SIZE;
-	case 2:
-		return CVMX_FPA_POOL_2_SIZE;
-	case 3:
-		return CVMX_FPA_POOL_3_SIZE;
-	case 4:
-		return CVMX_FPA_POOL_4_SIZE;
-	case 5:
-		return CVMX_FPA_POOL_5_SIZE;
-	case 6:
-		return CVMX_FPA_POOL_6_SIZE;
-	case 7:
-		return CVMX_FPA_POOL_7_SIZE;
-	default:
-		return 0;
-	}
-}

arch/mips/cavium-octeon/executive/cvmx-helper-fpa.c

@@ -1,243 +0,0 @@
-/***********************license start***************
- * Author: Cavium Networks
- *
- * Contact: support@caviumnetworks.com
- * This file is part of the OCTEON SDK
- *
- * Copyright (c) 2003-2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful, but
- * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
- * NONINFRINGEMENT.  See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this file; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- * or visit http://www.gnu.org/licenses/.
- *
- * This file may also be available under a different license from Cavium.
- * Contact Cavium Networks for more information
- ***********************license end**************************************/
-
-/**
- * @file
- *
- * Helper functions for FPA setup.
- *
- */
-#include "executive-config.h"
-#include "cvmx-config.h"
-#include "cvmx.h"
-#include "cvmx-bootmem.h"
-#include "cvmx-fpa.h"
-#include "cvmx-helper-fpa.h"
-
-/**
- * Allocate memory for and initialize a single FPA pool.
- *
- * @pool:    Pool to initialize
- * @buffer_size:  Size of buffers to allocate in bytes
- * @buffers: Number of buffers to put in the pool. Zero is allowed
- * @name:    String name of the pool for debugging purposes
- * Returns Zero on success, non-zero on failure
- */
-static int __cvmx_helper_initialize_fpa_pool(int pool, uint64_t buffer_size,
-					     uint64_t buffers, const char *name)
-{
-	uint64_t current_num;
-	void *memory;
-	uint64_t align = CVMX_CACHE_LINE_SIZE;
-
-	/*
-	 * Align the allocation so that power of 2 size buffers are
-	 * naturally aligned.
-	 */
-	while (align < buffer_size)
-		align = align << 1;
-
-	if (buffers == 0)
-		return 0;
-
-	current_num = cvmx_read_csr(CVMX_FPA_QUEX_AVAILABLE(pool));
-	if (current_num) {
-		cvmx_dprintf("Fpa pool %d(%s) already has %llu buffers. "
-			     "Skipping setup.\n",
-		     pool, name, (unsigned long long)current_num);
-		return 0;
-	}
-
-	memory = cvmx_bootmem_alloc(buffer_size * buffers, align);
-	if (memory == NULL) {
-		cvmx_dprintf("Out of memory initializing fpa pool %d(%s).\n",
-			     pool, name);
-		return -1;
-	}
-	cvmx_fpa_setup_pool(pool, name, memory, buffer_size, buffers);
-	return 0;
-}
-
-/**
- * Allocate memory and initialize the FPA pools using memory
- * from cvmx-bootmem. Specifying zero for the number of
- * buffers will cause that FPA pool to not be setup. This is
- * useful if you aren't using some of the hardware and want
- * to save memory. Use cvmx_helper_initialize_fpa instead of
- * this function directly.
- *
- * @pip_pool: Should always be CVMX_FPA_PACKET_POOL
- * @pip_size: Should always be CVMX_FPA_PACKET_POOL_SIZE
- * @pip_buffers:
- *                 Number of packet buffers.
- * @wqe_pool: Should always be CVMX_FPA_WQE_POOL
- * @wqe_size: Should always be CVMX_FPA_WQE_POOL_SIZE
- * @wqe_entries:
- *                 Number of work queue entries
- * @pko_pool: Should always be CVMX_FPA_OUTPUT_BUFFER_POOL
- * @pko_size: Should always be CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE
- * @pko_buffers:
- *                 PKO Command buffers. You should at minimum have two per
- *                 each PKO queue.
- * @tim_pool: Should always be CVMX_FPA_TIMER_POOL
- * @tim_size: Should always be CVMX_FPA_TIMER_POOL_SIZE
- * @tim_buffers:
- *                 TIM ring buffer command queues. At least two per timer bucket
- *                 is recommened.
- * @dfa_pool: Should always be CVMX_FPA_DFA_POOL
- * @dfa_size: Should always be CVMX_FPA_DFA_POOL_SIZE
- * @dfa_buffers:
- *                 DFA command buffer. A relatively small (32 for example)
- *                 number should work.
- * Returns Zero on success, non-zero if out of memory
- */
-static int __cvmx_helper_initialize_fpa(int pip_pool, int pip_size,
-					int pip_buffers, int wqe_pool,
-					int wqe_size, int wqe_entries,
-					int pko_pool, int pko_size,
-					int pko_buffers, int tim_pool,
-					int tim_size, int tim_buffers,
-					int dfa_pool, int dfa_size,
-					int dfa_buffers)
-{
-	int status;
-
-	cvmx_fpa_enable();
-
-	if ((pip_buffers > 0) && (pip_buffers <= 64))
-		cvmx_dprintf
-		    ("Warning: %d packet buffers may not be enough for hardware"
-		     " prefetch. 65 or more is recommended.\n", pip_buffers);
-
-	if (pip_pool >= 0) {
-		status =
-		    __cvmx_helper_initialize_fpa_pool(pip_pool, pip_size,
-						      pip_buffers,
-						      "Packet Buffers");
-		if (status)
-			return status;
-	}
-
-	if (wqe_pool >= 0) {
-		status =
-		    __cvmx_helper_initialize_fpa_pool(wqe_pool, wqe_size,
-						      wqe_entries,
-						      "Work Queue Entries");
-		if (status)
-			return status;
-	}
-
-	if (pko_pool >= 0) {
-		status =
-		    __cvmx_helper_initialize_fpa_pool(pko_pool, pko_size,
-						      pko_buffers,
-						      "PKO Command Buffers");
-		if (status)
-			return status;
-	}
-
-	if (tim_pool >= 0) {
-		status =
-		    __cvmx_helper_initialize_fpa_pool(tim_pool, tim_size,
-						      tim_buffers,
-						      "TIM Command Buffers");
-		if (status)
-			return status;
-	}
-
-	if (dfa_pool >= 0) {
-		status =
-		    __cvmx_helper_initialize_fpa_pool(dfa_pool, dfa_size,
-						      dfa_buffers,
-						      "DFA Command Buffers");
-		if (status)
-			return status;
-	}
-
-	return 0;
-}
-
-/**
- * Allocate memory and initialize the FPA pools using memory
- * from cvmx-bootmem. Sizes of each element in the pools is
- * controlled by the cvmx-config.h header file. Specifying
- * zero for any parameter will cause that FPA pool to not be
- * setup. This is useful if you aren't using some of the
- * hardware and want to save memory.
- *
- * @packet_buffers:
- *               Number of packet buffers to allocate
- * @work_queue_entries:
- *               Number of work queue entries
- * @pko_buffers:
- *               PKO Command buffers. You should at minimum have two per
- *               each PKO queue.
- * @tim_buffers:
- *               TIM ring buffer command queues. At least two per timer bucket
- *               is recommened.
- * @dfa_buffers:
- *               DFA command buffer. A relatively small (32 for example)
- *               number should work.
- * Returns Zero on success, non-zero if out of memory
- */
-int cvmx_helper_initialize_fpa(int packet_buffers, int work_queue_entries,
-			       int pko_buffers, int tim_buffers,
-			       int dfa_buffers)
-{
-#ifndef CVMX_FPA_PACKET_POOL
-#define CVMX_FPA_PACKET_POOL -1
-#define CVMX_FPA_PACKET_POOL_SIZE 0
-#endif
-#ifndef CVMX_FPA_WQE_POOL
-#define CVMX_FPA_WQE_POOL -1
-#define CVMX_FPA_WQE_POOL_SIZE 0
-#endif
-#ifndef CVMX_FPA_OUTPUT_BUFFER_POOL
-#define CVMX_FPA_OUTPUT_BUFFER_POOL -1
-#define CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE 0
-#endif
-#ifndef CVMX_FPA_TIMER_POOL
-#define CVMX_FPA_TIMER_POOL -1
-#define CVMX_FPA_TIMER_POOL_SIZE 0
-#endif
-#ifndef CVMX_FPA_DFA_POOL
-#define CVMX_FPA_DFA_POOL -1
-#define CVMX_FPA_DFA_POOL_SIZE 0
-#endif
-	return __cvmx_helper_initialize_fpa(CVMX_FPA_PACKET_POOL,
-					    CVMX_FPA_PACKET_POOL_SIZE,
-					    packet_buffers, CVMX_FPA_WQE_POOL,
-					    CVMX_FPA_WQE_POOL_SIZE,
-					    work_queue_entries,
-					    CVMX_FPA_OUTPUT_BUFFER_POOL,
-					    CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE,
-					    pko_buffers, CVMX_FPA_TIMER_POOL,
-					    CVMX_FPA_TIMER_POOL_SIZE,
-					    tim_buffers, CVMX_FPA_DFA_POOL,
-					    CVMX_FPA_DFA_POOL_SIZE,
-					    dfa_buffers);
-}

arch/mips/cavium-octeon/octeon-irq.c

@@ -3,14 +3,17 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 2004-2008, 2009, 2010, 2011 Cavium Networks
+ * Copyright (C) 2004-2012 Cavium, Inc.
  */
 
 #include <linux/interrupt.h>
+#include <linux/irqdomain.h>
 #include <linux/bitops.h>
 #include <linux/percpu.h>
+#include <linux/slab.h>
 #include <linux/irq.h>
 #include <linux/smp.h>
+#include <linux/of.h>
 
 #include <asm/octeon/octeon.h>
 
@@ -42,9 +45,9 @@ struct octeon_core_chip_data {
 
 static struct octeon_core_chip_data octeon_irq_core_chip_data[MIPS_CORE_IRQ_LINES];
 
-static void __init octeon_irq_set_ciu_mapping(int irq, int line, int bit,
-					      struct irq_chip *chip,
-					      irq_flow_handler_t handler)
+static void octeon_irq_set_ciu_mapping(int irq, int line, int bit,
+				       struct irq_chip *chip,
+				       irq_flow_handler_t handler)
 {
 	union octeon_ciu_chip_data cd;
 
@@ -505,6 +508,85 @@ static void octeon_irq_ciu_enable_all_v2(struct irq_data *data)
 	}
 }
 
+static void octeon_irq_gpio_setup(struct irq_data *data)
+{
+	union cvmx_gpio_bit_cfgx cfg;
+	union octeon_ciu_chip_data cd;
+	u32 t = irqd_get_trigger_type(data);
+
+	cd.p = irq_data_get_irq_chip_data(data);
+
+	cfg.u64 = 0;
+	cfg.s.int_en = 1;
+	cfg.s.int_type = (t & IRQ_TYPE_EDGE_BOTH) != 0;
+	cfg.s.rx_xor = (t & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING)) != 0;
+
+	/* 140 nS glitch filter*/
+	cfg.s.fil_cnt = 7;
+	cfg.s.fil_sel = 3;
+
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd.s.bit - 16), cfg.u64);
+}
+
+static void octeon_irq_ciu_enable_gpio_v2(struct irq_data *data)
+{
+	octeon_irq_gpio_setup(data);
+	octeon_irq_ciu_enable_v2(data);
+}
+
+static void octeon_irq_ciu_enable_gpio(struct irq_data *data)
+{
+	octeon_irq_gpio_setup(data);
+	octeon_irq_ciu_enable(data);
+}
+
+static int octeon_irq_ciu_gpio_set_type(struct irq_data *data, unsigned int t)
+{
+	irqd_set_trigger_type(data, t);
+	octeon_irq_gpio_setup(data);
+
+	return IRQ_SET_MASK_OK;
+}
+
+static void octeon_irq_ciu_disable_gpio_v2(struct irq_data *data)
+{
+	union octeon_ciu_chip_data cd;
+
+	cd.p = irq_data_get_irq_chip_data(data);
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd.s.bit - 16), 0);
+
+	octeon_irq_ciu_disable_all_v2(data);
+}
+
+static void octeon_irq_ciu_disable_gpio(struct irq_data *data)
+{
+	union octeon_ciu_chip_data cd;
+
+	cd.p = irq_data_get_irq_chip_data(data);
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd.s.bit - 16), 0);
+
+	octeon_irq_ciu_disable_all(data);
+}
+
+static void octeon_irq_ciu_gpio_ack(struct irq_data *data)
+{
+	union octeon_ciu_chip_data cd;
+	u64 mask;
+
+	cd.p = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd.s.bit - 16);
+
+	cvmx_write_csr(CVMX_GPIO_INT_CLR, mask);
+}
+
+static void octeon_irq_handle_gpio(unsigned int irq, struct irq_desc *desc)
+{
+	if (irqd_get_trigger_type(irq_desc_get_irq_data(desc)) & IRQ_TYPE_EDGE_BOTH)
+		handle_edge_irq(irq, desc);
+	else
+		handle_level_irq(irq, desc);
+}
+
 #ifdef CONFIG_SMP
 
 static void octeon_irq_cpu_offline_ciu(struct irq_data *data)
@@ -650,18 +732,6 @@ static struct irq_chip octeon_irq_chip_ciu_v2 = {
 	.name = "CIU",
 	.irq_enable = octeon_irq_ciu_enable_v2,
 	.irq_disable = octeon_irq_ciu_disable_all_v2,
-	.irq_mask = octeon_irq_ciu_disable_local_v2,
-	.irq_unmask = octeon_irq_ciu_enable_v2,
-#ifdef CONFIG_SMP
-	.irq_set_affinity = octeon_irq_ciu_set_affinity_v2,
-	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
-#endif
-};
-
-static struct irq_chip octeon_irq_chip_ciu_edge_v2 = {
-	.name = "CIU-E",
-	.irq_enable = octeon_irq_ciu_enable_v2,
-	.irq_disable = octeon_irq_ciu_disable_all_v2,
 	.irq_ack = octeon_irq_ciu_ack,
 	.irq_mask = octeon_irq_ciu_disable_local_v2,
 	.irq_unmask = octeon_irq_ciu_enable_v2,
@@ -675,19 +745,8 @@ static struct irq_chip octeon_irq_chip_ciu = {
 	.name = "CIU",
 	.irq_enable = octeon_irq_ciu_enable,
 	.irq_disable = octeon_irq_ciu_disable_all,
-	.irq_mask = octeon_irq_dummy_mask,
-#ifdef CONFIG_SMP
-	.irq_set_affinity = octeon_irq_ciu_set_affinity,
-	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
-#endif
-};
-
-static struct irq_chip octeon_irq_chip_ciu_edge = {
-	.name = "CIU-E",
-	.irq_enable = octeon_irq_ciu_enable,
-	.irq_disable = octeon_irq_ciu_disable_all,
-	.irq_mask = octeon_irq_dummy_mask,
 	.irq_ack = octeon_irq_ciu_ack,
+	.irq_mask = octeon_irq_dummy_mask,
 #ifdef CONFIG_SMP
 	.irq_set_affinity = octeon_irq_ciu_set_affinity,
 	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
@@ -717,6 +776,33 @@ static struct irq_chip octeon_irq_chip_ciu_mbox = {
 	.flags = IRQCHIP_ONOFFLINE_ENABLED,
 };
 
+static struct irq_chip octeon_irq_chip_ciu_gpio_v2 = {
+	.name = "CIU-GPIO",
+	.irq_enable = octeon_irq_ciu_enable_gpio_v2,
+	.irq_disable = octeon_irq_ciu_disable_gpio_v2,
+	.irq_ack = octeon_irq_ciu_gpio_ack,
+	.irq_mask = octeon_irq_ciu_disable_local_v2,
+	.irq_unmask = octeon_irq_ciu_enable_v2,
+	.irq_set_type = octeon_irq_ciu_gpio_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_v2,
+#endif
+	.flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
+static struct irq_chip octeon_irq_chip_ciu_gpio = {
+	.name = "CIU-GPIO",
+	.irq_enable = octeon_irq_ciu_enable_gpio,
+	.irq_disable = octeon_irq_ciu_disable_gpio,
+	.irq_mask = octeon_irq_dummy_mask,
+	.irq_ack = octeon_irq_ciu_gpio_ack,
+	.irq_set_type = octeon_irq_ciu_gpio_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity,
+#endif
+	.flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
 /*
  * Watchdog interrupts are special.  They are associated with a single
  * core, so we hardwire the affinity to that core.
@@ -764,6 +850,178 @@ static struct irq_chip octeon_irq_chip_ciu_wd = {
 	.irq_mask = octeon_irq_dummy_mask,
 };
 
+static bool octeon_irq_ciu_is_edge(unsigned int line, unsigned int bit)
+{
+	bool edge = false;
+
+	if (line == 0)
+		switch (bit) {
+		case 48 ... 49: /* GMX DRP */
+		case 50: /* IPD_DRP */
+		case 52 ... 55: /* Timers */
+		case 58: /* MPI */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	else /* line == 1 */
+		switch (bit) {
+		case 47: /* PTP */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	return edge;
+}
+
+struct octeon_irq_gpio_domain_data {
+	unsigned int base_hwirq;
+};
+
+static int octeon_irq_gpio_xlat(struct irq_domain *d,
+				struct device_node *node,
+				const u32 *intspec,
+				unsigned int intsize,
+				unsigned long *out_hwirq,
+				unsigned int *out_type)
+{
+	unsigned int type;
+	unsigned int pin;
+	unsigned int trigger;
+	struct octeon_irq_gpio_domain_data *gpiod;
+
+	if (d->of_node != node)
+		return -EINVAL;
+
+	if (intsize < 2)
+		return -EINVAL;
+
+	pin = intspec[0];
+	if (pin >= 16)
+		return -EINVAL;
+
+	trigger = intspec[1];
+
+	switch (trigger) {
+	case 1:
+		type = IRQ_TYPE_EDGE_RISING;
+		break;
+	case 2:
+		type = IRQ_TYPE_EDGE_FALLING;
+		break;
+	case 4:
+		type = IRQ_TYPE_LEVEL_HIGH;
+		break;
+	case 8:
+		type = IRQ_TYPE_LEVEL_LOW;
+		break;
+	default:
+		pr_err("Error: (%s) Invalid irq trigger specification: %x\n",
+		       node->name,
+		       trigger);
+		type = IRQ_TYPE_LEVEL_LOW;
+		break;
+	}
+	*out_type = type;
+	gpiod = d->host_data;
+	*out_hwirq = gpiod->base_hwirq + pin;
+
+	return 0;
+}
+
+static int octeon_irq_ciu_xlat(struct irq_domain *d,
+			       struct device_node *node,
+			       const u32 *intspec,
+			       unsigned int intsize,
+			       unsigned long *out_hwirq,
+			       unsigned int *out_type)
+{
+	unsigned int ciu, bit;
+
+	ciu = intspec[0];
+	bit = intspec[1];
+
+	if (ciu > 1 || bit > 63)
+		return -EINVAL;
+
+	/* These are the GPIO lines */
+	if (ciu == 0 && bit >= 16 && bit < 32)
+		return -EINVAL;
+
+	*out_hwirq = (ciu << 6) | bit;
+	*out_type = 0;
+
+	return 0;
+}
+
+static struct irq_chip *octeon_irq_ciu_chip;
+static struct irq_chip *octeon_irq_gpio_chip;
+
+static bool octeon_irq_virq_in_range(unsigned int virq)
+{
+	/* We cannot let it overflow the mapping array. */
+	if (virq < (1ul << 8 * sizeof(octeon_irq_ciu_to_irq[0][0])))
+		return true;
+
+	WARN_ONCE(true, "virq out of range %u.\n", virq);
+	return false;
+}
+
+static int octeon_irq_ciu_map(struct irq_domain *d,
+			      unsigned int virq, irq_hw_number_t hw)
+{
+	unsigned int line = hw >> 6;
+	unsigned int bit = hw & 63;
+
+	if (!octeon_irq_virq_in_range(virq))
+		return -EINVAL;
+
+	if (line > 1 || octeon_irq_ciu_to_irq[line][bit] != 0)
+		return -EINVAL;
+
+	if (octeon_irq_ciu_is_edge(line, bit))
+		octeon_irq_set_ciu_mapping(virq, line, bit,
+					   octeon_irq_ciu_chip,
+					   handle_edge_irq);
+	else
+		octeon_irq_set_ciu_mapping(virq, line, bit,
+					   octeon_irq_ciu_chip,
+					   handle_level_irq);
+
+	return 0;
+}
+
+static int octeon_irq_gpio_map(struct irq_domain *d,
+			       unsigned int virq, irq_hw_number_t hw)
+{
+	unsigned int line = hw >> 6;
+	unsigned int bit = hw & 63;
+
+	if (!octeon_irq_virq_in_range(virq))
+		return -EINVAL;
+
+	if (line > 1 || octeon_irq_ciu_to_irq[line][bit] != 0)
+		return -EINVAL;
+
+	octeon_irq_set_ciu_mapping(virq, line, bit,
+				   octeon_irq_gpio_chip,
+				   octeon_irq_handle_gpio);
+
+	return 0;
+}
+
+static struct irq_domain_ops octeon_irq_domain_ciu_ops = {
+	.map = octeon_irq_ciu_map,
+	.xlate = octeon_irq_ciu_xlat,
+};
+
+static struct irq_domain_ops octeon_irq_domain_gpio_ops = {
+	.map = octeon_irq_gpio_map,
+	.xlate = octeon_irq_gpio_xlat,
+};
+
 static void octeon_irq_ip2_v1(void)
 {
 	const unsigned long core_id = cvmx_get_core_num();
@@ -887,9 +1145,10 @@ static void __init octeon_irq_init_ciu(void)
 {
 	unsigned int i;
 	struct irq_chip *chip;
-	struct irq_chip *chip_edge;
 	struct irq_chip *chip_mbox;
 	struct irq_chip *chip_wd;
+	struct device_node *gpio_node;
+	struct device_node *ciu_node;
 
 	octeon_irq_init_ciu_percpu();
 	octeon_irq_setup_secondary = octeon_irq_setup_secondary_ciu;
@@ -901,17 +1160,18 @@ static void __init octeon_irq_init_ciu(void)
 		octeon_irq_ip2 = octeon_irq_ip2_v2;
 		octeon_irq_ip3 = octeon_irq_ip3_v2;
 		chip = &octeon_irq_chip_ciu_v2;
-		chip_edge = &octeon_irq_chip_ciu_edge_v2;
 		chip_mbox = &octeon_irq_chip_ciu_mbox_v2;
 		chip_wd = &octeon_irq_chip_ciu_wd_v2;
+		octeon_irq_gpio_chip = &octeon_irq_chip_ciu_gpio_v2;
 	} else {
 		octeon_irq_ip2 = octeon_irq_ip2_v1;
 		octeon_irq_ip3 = octeon_irq_ip3_v1;
 		chip = &octeon_irq_chip_ciu;
-		chip_edge = &octeon_irq_chip_ciu_edge;
 		chip_mbox = &octeon_irq_chip_ciu_mbox;
 		chip_wd = &octeon_irq_chip_ciu_wd;
+		octeon_irq_gpio_chip = &octeon_irq_chip_ciu_gpio;
 	}
+	octeon_irq_ciu_chip = chip;
 	octeon_irq_ip4 = octeon_irq_ip4_mask;
 
 	/* Mips internal */
@@ -920,80 +1180,49 @@ static void __init octeon_irq_init_ciu(void)
 	/* CIU_0 */
 	for (i = 0; i < 16; i++)
 		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WORKQ0, 0, i + 0, chip, handle_level_irq);
-	for (i = 0; i < 16; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_GPIO0, 0, i + 16, chip, handle_level_irq);
 
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX0, 0, 32, chip_mbox, handle_percpu_irq);
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MBOX1, 0, 33, chip_mbox, handle_percpu_irq);
 
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_UART0, 0, 34, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_UART1, 0, 35, chip, handle_level_irq);
-
 	for (i = 0; i < 4; i++)
 		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_PCI_INT0, 0, i + 36, chip, handle_level_irq);
 	for (i = 0; i < 4; i++)
 		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_PCI_MSI0, 0, i + 40, chip, handle_level_irq);
 
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_TWSI, 0, 45, chip, handle_level_irq);
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_RML, 0, 46, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_TRACE0, 0, 47, chip, handle_level_irq);
-
-	for (i = 0; i < 2; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_GMX_DRP0, 0, i + 48, chip_edge, handle_edge_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_IPD_DRP, 0, 50, chip_edge, handle_edge_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_KEY_ZERO, 0, 51, chip_edge, handle_edge_irq);
-
 	for (i = 0; i < 4; i++)
-		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_TIMER0, 0, i + 52, chip_edge, handle_edge_irq);
+		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_TIMER0, 0, i + 52, chip, handle_edge_irq);
 
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_USB0, 0, 56, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PCM, 0, 57, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MPI, 0, 58, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_TWSI2, 0, 59, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_POWIQ, 0, 60, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_IPDPPTHR, 0, 61, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MII0, 0, 62, chip, handle_level_irq);
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_BOOTDMA, 0, 63, chip, handle_level_irq);
 
 	/* CIU_1 */
 	for (i = 0; i < 16; i++)
 		octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WDOG0, 1, i + 0, chip_wd, handle_level_irq);
 
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_UART2, 1, 16, chip, handle_level_irq);
 	octeon_irq_set_ciu_mapping(OCTEON_IRQ_USB1, 1, 17, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MII1, 1, 18, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_NAND, 1, 19, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_MIO, 1, 20, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_IOB, 1, 21, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_FPA, 1, 22, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_POW, 1, 23, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_L2C, 1, 24, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_IPD, 1, 25, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PIP, 1, 26, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PKO, 1, 27, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_ZIP, 1, 28, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_TIM, 1, 29, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_RAD, 1, 30, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_KEY, 1, 31, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_DFA, 1, 32, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_USBCTL, 1, 33, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_SLI, 1, 34, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_DPI, 1, 35, chip, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_AGX0, 1, 36, chip, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_AGL, 1, 46, chip, handle_level_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PTP, 1, 47, chip_edge, handle_edge_irq);
-
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PEM0, 1, 48, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_PEM1, 1, 49, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_SRIO0, 1, 50, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_SRIO1, 1, 51, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_LMC0, 1, 52, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_DFM, 1, 56, chip, handle_level_irq);
-	octeon_irq_set_ciu_mapping(OCTEON_IRQ_RST, 1, 63, chip, handle_level_irq);
+
+	gpio_node = of_find_compatible_node(NULL, NULL, "cavium,octeon-3860-gpio");
+	if (gpio_node) {
+		struct octeon_irq_gpio_domain_data *gpiod;
+
+		gpiod = kzalloc(sizeof(*gpiod), GFP_KERNEL);
+		if (gpiod) {
+			/* gpio domain host_data is the base hwirq number. */
+			gpiod->base_hwirq = 16;
+			irq_domain_add_linear(gpio_node, 16, &octeon_irq_domain_gpio_ops, gpiod);
+			of_node_put(gpio_node);
+		} else
+			pr_warn("Cannot allocate memory for GPIO irq_domain.\n");
+	} else
+		pr_warn("Cannot find device node for cavium,octeon-3860-gpio.\n");
+
+	ciu_node = of_find_compatible_node(NULL, NULL, "cavium,octeon-3860-ciu");
+	if (ciu_node) {
+		irq_domain_add_tree(ciu_node, &octeon_irq_domain_ciu_ops, NULL);
+		of_node_put(ciu_node);
+	} else
+		pr_warn("Cannot find device node for cavium,octeon-3860-ciu.\n");
 
 	/* Enable the CIU lines */
 	set_c0_status(STATUSF_IP3 | STATUSF_IP2);

arch/mips/cavium-octeon/octeon-memcpy.S

@@ -163,6 +163,14 @@
 	.set	noreorder
 	.set	noat
 
+/*
+ * t7 is used as a flag to note inatomic mode.
+ */
+LEAF(__copy_user_inatomic)
+	b	__copy_user_common
+	 li	t7, 1
+	END(__copy_user_inatomic)
+
 /*
  * A combined memcpy/__copy_user
  * __copy_user sets len to 0 for success; else to an upper bound of
@@ -174,6 +182,8 @@ LEAF(memcpy)					/* a0=dst a1=src a2=len */
 	move	v0, dst				/* return value */
 __memcpy:
 FEXPORT(__copy_user)
+	li	t7, 0				/* not inatomic */
+__copy_user_common:
 	/*
 	 * Note: dst & src may be unaligned, len may be 0
 	 * Temps
@@ -412,7 +422,6 @@ l_exc_copy:
 	 * Assumes src < THREAD_BUADDR($28)
 	 */
 	LOAD	t0, TI_TASK($28)
-	 nop
 	LOAD	t0, THREAD_BUADDR(t0)
 1:
 EXC(	lb	t1, 0(src),	l_exc)
@@ -422,10 +431,9 @@ EXC(	lb	t1, 0(src),	l_exc)
 	 ADD	dst, dst, 1
 l_exc:
 	LOAD	t0, TI_TASK($28)
-	 nop
 	LOAD	t0, THREAD_BUADDR(t0)	# t0 is just past last good address
-	 nop
 	SUB	len, AT, t0		# len number of uncopied bytes
+	bnez	t7, 2f		/* Skip the zeroing out part if inatomic */
 	/*
 	 * Here's where we rely on src and dst being incremented in tandem,
 	 *   See (3) above.
@@ -443,7 +451,7 @@ l_exc:
 	ADD	dst, dst, 1
 	bnez	src, 1b
 	 SUB	src, src, 1
-	jr	ra
+2:	jr	ra
 	 nop
 
 

arch/mips/cavium-octeon/octeon-platform.c

@@ -3,7 +3,7 @@
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  *
- * Copyright (C) 2004-2010 Cavium Networks
+ * Copyright (C) 2004-2011 Cavium Networks
  * Copyright (C) 2008 Wind River Systems
  */
 
@@ -13,10 +13,16 @@
 #include <linux/usb.h>
 #include <linux/dma-mapping.h>
 #include <linux/module.h>
+#include <linux/slab.h>
 #include <linux/platform_device.h>
+#include <linux/of_platform.h>
+#include <linux/of_fdt.h>
+#include <linux/libfdt.h>
 
 #include <asm/octeon/octeon.h>
 #include <asm/octeon/cvmx-rnm-defs.h>
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-board.h>
 
 static struct octeon_cf_data octeon_cf_data;
 
@@ -162,182 +168,6 @@ out:
 }
 device_initcall(octeon_rng_device_init);
 
-static struct i2c_board_info __initdata octeon_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("ds1337", 0x68),
-	},
-};
-
-static int __init octeon_i2c_devices_init(void)
-{
-	return i2c_register_board_info(0, octeon_i2c_devices,
-				       ARRAY_SIZE(octeon_i2c_devices));
-}
-arch_initcall(octeon_i2c_devices_init);
-
-#define OCTEON_I2C_IO_BASE 0x1180000001000ull
-#define OCTEON_I2C_IO_UNIT_OFFSET 0x200
-
-static struct octeon_i2c_data octeon_i2c_data[2];
-
-static int __init octeon_i2c_device_init(void)
-{
-	struct platform_device *pd;
-	int ret = 0;
-	int port, num_ports;
-
-	struct resource i2c_resources[] = {
-		{
-			.flags	= IORESOURCE_MEM,
-		}, {
-			.flags	= IORESOURCE_IRQ,
-		}
-	};
-
-	if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN52XX))
-		num_ports = 2;
-	else
-		num_ports = 1;
-
-	for (port = 0; port < num_ports; port++) {
-		octeon_i2c_data[port].sys_freq = octeon_get_io_clock_rate();
-		/*FIXME: should be examined. At the moment is set for 100Khz */
-		octeon_i2c_data[port].i2c_freq = 100000;
-
-		pd = platform_device_alloc("i2c-octeon", port);
-		if (!pd) {
-			ret = -ENOMEM;
-			goto out;
-		}
-
-		pd->dev.platform_data = octeon_i2c_data + port;
-
-		i2c_resources[0].start =
-			OCTEON_I2C_IO_BASE + (port * OCTEON_I2C_IO_UNIT_OFFSET);
-		i2c_resources[0].end = i2c_resources[0].start + 0x1f;
-		switch (port) {
-		case 0:
-			i2c_resources[1].start = OCTEON_IRQ_TWSI;
-			i2c_resources[1].end = OCTEON_IRQ_TWSI;
-			break;
-		case 1:
-			i2c_resources[1].start = OCTEON_IRQ_TWSI2;
-			i2c_resources[1].end = OCTEON_IRQ_TWSI2;
-			break;
-		default:
-			BUG();
-		}
-
-		ret = platform_device_add_resources(pd,
-						    i2c_resources,
-						    ARRAY_SIZE(i2c_resources));
-		if (ret)
-			goto fail;
-
-		ret = platform_device_add(pd);
-		if (ret)
-			goto fail;
-	}
-	return ret;
-fail:
-	platform_device_put(pd);
-out:
-	return ret;
-}
-device_initcall(octeon_i2c_device_init);
-
-/* Octeon SMI/MDIO interface.  */
-static int __init octeon_mdiobus_device_init(void)
-{
-	struct platform_device *pd;
-	int ret = 0;
-
-	if (octeon_is_simulation())
-		return 0; /* No mdio in the simulator. */
-
-	/* The bus number is the platform_device id.  */
-	pd = platform_device_alloc("mdio-octeon", 0);
-	if (!pd) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	ret = platform_device_add(pd);
-	if (ret)
-		goto fail;
-
-	return ret;
-fail:
-	platform_device_put(pd);
-
-out:
-	return ret;
-
-}
-device_initcall(octeon_mdiobus_device_init);
-
-/* Octeon mgmt port Ethernet interface.  */
-static int __init octeon_mgmt_device_init(void)
-{
-	struct platform_device *pd;
-	int ret = 0;
-	int port, num_ports;
-
-	struct resource mgmt_port_resource = {
-		.flags	= IORESOURCE_IRQ,
-		.start	= -1,
-		.end	= -1
-	};
-
-	if (!OCTEON_IS_MODEL(OCTEON_CN56XX) && !OCTEON_IS_MODEL(OCTEON_CN52XX))
-		return 0;
-
-	if (OCTEON_IS_MODEL(OCTEON_CN56XX))
-		num_ports = 1;
-	else
-		num_ports = 2;
-
-	for (port = 0; port < num_ports; port++) {
-		pd = platform_device_alloc("octeon_mgmt", port);
-		if (!pd) {
-			ret = -ENOMEM;
-			goto out;
-		}
-		/* No DMA restrictions */
-		pd->dev.coherent_dma_mask = DMA_BIT_MASK(64);
-		pd->dev.dma_mask = &pd->dev.coherent_dma_mask;
-
-		switch (port) {
-		case 0:
-			mgmt_port_resource.start = OCTEON_IRQ_MII0;
-			break;
-		case 1:
-			mgmt_port_resource.start = OCTEON_IRQ_MII1;
-			break;
-		default:
-			BUG();
-		}
-		mgmt_port_resource.end = mgmt_port_resource.start;
-
-		ret = platform_device_add_resources(pd, &mgmt_port_resource, 1);
-
-		if (ret)
-			goto fail;
-
-		ret = platform_device_add(pd);
-		if (ret)
-			goto fail;
-	}
-	return ret;
-fail:
-	platform_device_put(pd);
-
-out:
-	return ret;
-
-}
-device_initcall(octeon_mgmt_device_init);
-
 #ifdef CONFIG_USB
 
 static int __init octeon_ehci_device_init(void)
@@ -440,6 +270,521 @@ device_initcall(octeon_ohci_device_init);
 
 #endif /* CONFIG_USB */
 
+static struct of_device_id __initdata octeon_ids[] = {
+	{ .compatible = "simple-bus", },
+	{ .compatible = "cavium,octeon-6335-uctl", },
+	{ .compatible = "cavium,octeon-3860-bootbus", },
+	{ .compatible = "cavium,mdio-mux", },
+	{ .compatible = "gpio-leds", },
+	{},
+};
+
+static bool __init octeon_has_88e1145(void)
+{
+	return !OCTEON_IS_MODEL(OCTEON_CN52XX) &&
+	       !OCTEON_IS_MODEL(OCTEON_CN6XXX) &&
+	       !OCTEON_IS_MODEL(OCTEON_CN56XX);
+}
+
+static void __init octeon_fdt_set_phy(int eth, int phy_addr)
+{
+	const __be32 *phy_handle;
+	const __be32 *alt_phy_handle;
+	const __be32 *reg;
+	u32 phandle;
+	int phy;
+	int alt_phy;
+	const char *p;
+	int current_len;
+	char new_name[20];
+
+	phy_handle = fdt_getprop(initial_boot_params, eth, "phy-handle", NULL);
+	if (!phy_handle)
+		return;
+
+	phandle = be32_to_cpup(phy_handle);
+	phy = fdt_node_offset_by_phandle(initial_boot_params, phandle);
+
+	alt_phy_handle = fdt_getprop(initial_boot_params, eth, "cavium,alt-phy-handle", NULL);
+	if (alt_phy_handle) {
+		u32 alt_phandle = be32_to_cpup(alt_phy_handle);
+		alt_phy = fdt_node_offset_by_phandle(initial_boot_params, alt_phandle);
+	} else {
+		alt_phy = -1;
+	}
+
+	if (phy_addr < 0 || phy < 0) {
+		/* Delete the PHY things */
+		fdt_nop_property(initial_boot_params, eth, "phy-handle");
+		/* This one may fail */
+		fdt_nop_property(initial_boot_params, eth, "cavium,alt-phy-handle");
+		if (phy >= 0)
+			fdt_nop_node(initial_boot_params, phy);
+		if (alt_phy >= 0)
+			fdt_nop_node(initial_boot_params, alt_phy);
+		return;
+	}
+
+	if (phy_addr >= 256 && alt_phy > 0) {
+		const struct fdt_property *phy_prop;
+		struct fdt_property *alt_prop;
+		u32 phy_handle_name;
+
+		/* Use the alt phy node instead.*/
+		phy_prop = fdt_get_property(initial_boot_params, eth, "phy-handle", NULL);
+		phy_handle_name = phy_prop->nameoff;
+		fdt_nop_node(initial_boot_params, phy);
+		fdt_nop_property(initial_boot_params, eth, "phy-handle");
+		alt_prop = fdt_get_property_w(initial_boot_params, eth, "cavium,alt-phy-handle", NULL);
+		alt_prop->nameoff = phy_handle_name;
+		phy = alt_phy;
+	}
+
+	phy_addr &= 0xff;
+
+	if (octeon_has_88e1145()) {
+		fdt_nop_property(initial_boot_params, phy, "marvell,reg-init");
+		memset(new_name, 0, sizeof(new_name));
+		strcpy(new_name, "marvell,88e1145");
+		p = fdt_getprop(initial_boot_params, phy, "compatible",
+				&current_len);
+		if (p && current_len >= strlen(new_name))
+			fdt_setprop_inplace(initial_boot_params, phy,
+					"compatible", new_name, current_len);
+	}
+
+	reg = fdt_getprop(initial_boot_params, phy, "reg", NULL);
+	if (phy_addr == be32_to_cpup(reg))
+		return;
+
+	fdt_setprop_inplace_cell(initial_boot_params, phy, "reg", phy_addr);
+
+	snprintf(new_name, sizeof(new_name), "ethernet-phy@%x", phy_addr);
+
+	p = fdt_get_name(initial_boot_params, phy, &current_len);
+	if (p && current_len == strlen(new_name))
+		fdt_set_name(initial_boot_params, phy, new_name);
+	else
+		pr_err("Error: could not rename ethernet phy: <%s>", p);
+}
+
+static void __init octeon_fdt_set_mac_addr(int n, u64 *pmac)
+{
+	u8 new_mac[6];
+	u64 mac = *pmac;
+	int r;
+
+	new_mac[0] = (mac >> 40) & 0xff;
+	new_mac[1] = (mac >> 32) & 0xff;
+	new_mac[2] = (mac >> 24) & 0xff;
+	new_mac[3] = (mac >> 16) & 0xff;
+	new_mac[4] = (mac >> 8) & 0xff;
+	new_mac[5] = mac & 0xff;
+
+	r = fdt_setprop_inplace(initial_boot_params, n, "local-mac-address",
+				new_mac, sizeof(new_mac));
+
+	if (r) {
+		pr_err("Setting \"local-mac-address\" failed %d", r);
+		return;
+	}
+	*pmac = mac + 1;
+}
+
+static void __init octeon_fdt_rm_ethernet(int node)
+{
+	const __be32 *phy_handle;
+
+	phy_handle = fdt_getprop(initial_boot_params, node, "phy-handle", NULL);
+	if (phy_handle) {
+		u32 ph = be32_to_cpup(phy_handle);
+		int p = fdt_node_offset_by_phandle(initial_boot_params, ph);
+		if (p >= 0)
+			fdt_nop_node(initial_boot_params, p);
+	}
+	fdt_nop_node(initial_boot_params, node);
+}
+
+static void __init octeon_fdt_pip_port(int iface, int i, int p, int max, u64 *pmac)
+{
+	char name_buffer[20];
+	int eth;
+	int phy_addr;
+	int ipd_port;
+
+	snprintf(name_buffer, sizeof(name_buffer), "ethernet@%x", p);
+	eth = fdt_subnode_offset(initial_boot_params, iface, name_buffer);
+	if (eth < 0)
+		return;
+	if (p > max) {
+		pr_debug("Deleting port %x:%x\n", i, p);
+		octeon_fdt_rm_ethernet(eth);
+		return;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		ipd_port = (0x100 * i) + (0x10 * p) + 0x800;
+	else
+		ipd_port = 16 * i + p;
+
+	phy_addr = cvmx_helper_board_get_mii_address(ipd_port);
+	octeon_fdt_set_phy(eth, phy_addr);
+	octeon_fdt_set_mac_addr(eth, pmac);
+}
+
+static void __init octeon_fdt_pip_iface(int pip, int idx, u64 *pmac)
+{
+	char name_buffer[20];
+	int iface;
+	int p;
+	int count;
+
+	count = cvmx_helper_interface_enumerate(idx);
+
+	snprintf(name_buffer, sizeof(name_buffer), "interface@%d", idx);
+	iface = fdt_subnode_offset(initial_boot_params, pip, name_buffer);
+	if (iface < 0)
+		return;
+
+	for (p = 0; p < 16; p++)
+		octeon_fdt_pip_port(iface, idx, p, count - 1, pmac);
+}
+
+int __init octeon_prune_device_tree(void)
+{
+	int i, max_port, uart_mask;
+	const char *pip_path;
+	const char *alias_prop;
+	char name_buffer[20];
+	int aliases;
+	u64 mac_addr_base;
+
+	if (fdt_check_header(initial_boot_params))
+		panic("Corrupt Device Tree.");
+
+	aliases = fdt_path_offset(initial_boot_params, "/aliases");
+	if (aliases < 0) {
+		pr_err("Error: No /aliases node in device tree.");
+		return -EINVAL;
+	}
+
+
+	mac_addr_base =
+		((octeon_bootinfo->mac_addr_base[0] & 0xffull)) << 40 |
+		((octeon_bootinfo->mac_addr_base[1] & 0xffull)) << 32 |
+		((octeon_bootinfo->mac_addr_base[2] & 0xffull)) << 24 |
+		((octeon_bootinfo->mac_addr_base[3] & 0xffull)) << 16 |
+		((octeon_bootinfo->mac_addr_base[4] & 0xffull)) << 8 |
+		(octeon_bootinfo->mac_addr_base[5] & 0xffull);
+
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX) || OCTEON_IS_MODEL(OCTEON_CN63XX))
+		max_port = 2;
+	else if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN68XX))
+		max_port = 1;
+	else
+		max_port = 0;
+
+	if (octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC10E)
+		max_port = 0;
+
+	for (i = 0; i < 2; i++) {
+		int mgmt;
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "mix%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+		if (alias_prop) {
+			mgmt = fdt_path_offset(initial_boot_params, alias_prop);
+			if (mgmt < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting mix%d\n", i);
+				octeon_fdt_rm_ethernet(mgmt);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			} else {
+				int phy_addr = cvmx_helper_board_get_mii_address(CVMX_HELPER_BOARD_MGMT_IPD_PORT + i);
+				octeon_fdt_set_phy(mgmt, phy_addr);
+				octeon_fdt_set_mac_addr(mgmt, &mac_addr_base);
+			}
+		}
+	}
+
+	pip_path = fdt_getprop(initial_boot_params, aliases, "pip", NULL);
+	if (pip_path) {
+		int pip = fdt_path_offset(initial_boot_params, pip_path);
+		if (pip  >= 0)
+			for (i = 0; i <= 4; i++)
+				octeon_fdt_pip_iface(pip, i, &mac_addr_base);
+	}
+
+	/* I2C */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN63XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN68XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX))
+		max_port = 2;
+	else
+		max_port = 1;
+
+	for (i = 0; i < 2; i++) {
+		int i2c;
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "twsi%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+
+		if (alias_prop) {
+			i2c = fdt_path_offset(initial_boot_params, alias_prop);
+			if (i2c < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting twsi%d\n", i);
+				fdt_nop_node(initial_boot_params, i2c);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			}
+		}
+	}
+
+	/* SMI/MDIO */
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		max_port = 4;
+	else if (OCTEON_IS_MODEL(OCTEON_CN52XX) ||
+		 OCTEON_IS_MODEL(OCTEON_CN63XX) ||
+		 OCTEON_IS_MODEL(OCTEON_CN56XX))
+		max_port = 2;
+	else
+		max_port = 1;
+
+	for (i = 0; i < 2; i++) {
+		int i2c;
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "smi%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+
+		if (alias_prop) {
+			i2c = fdt_path_offset(initial_boot_params, alias_prop);
+			if (i2c < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting smi%d\n", i);
+				fdt_nop_node(initial_boot_params, i2c);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			}
+		}
+	}
+
+	/* Serial */
+	uart_mask = 3;
+
+	/* Right now CN52XX is the only chip with a third uart */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX))
+		uart_mask |= 4; /* uart2 */
+
+	for (i = 0; i < 3; i++) {
+		int uart;
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "uart%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+
+		if (alias_prop) {
+			uart = fdt_path_offset(initial_boot_params, alias_prop);
+			if (uart_mask & (1 << i))
+				continue;
+			pr_debug("Deleting uart%d\n", i);
+			fdt_nop_node(initial_boot_params, uart);
+			fdt_nop_property(initial_boot_params, aliases,
+					 name_buffer);
+		}
+	}
+
+	/* Compact Flash */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "cf0", NULL);
+	if (alias_prop) {
+		union cvmx_mio_boot_reg_cfgx mio_boot_reg_cfg;
+		unsigned long base_ptr, region_base, region_size;
+		unsigned long region1_base = 0;
+		unsigned long region1_size = 0;
+		int cs, bootbus;
+		bool is_16bit = false;
+		bool is_true_ide = false;
+		__be32 new_reg[6];
+		__be32 *ranges;
+		int len;
+
+		int cf = fdt_path_offset(initial_boot_params, alias_prop);
+		base_ptr = 0;
+		if (octeon_bootinfo->major_version == 1
+			&& octeon_bootinfo->minor_version >= 1) {
+			if (octeon_bootinfo->compact_flash_common_base_addr)
+				base_ptr = octeon_bootinfo->compact_flash_common_base_addr;
+		} else {
+			base_ptr = 0x1d000800;
+		}
+
+		if (!base_ptr)
+			goto no_cf;
+
+		/* Find CS0 region. */
+		for (cs = 0; cs < 8; cs++) {
+			mio_boot_reg_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs));
+			region_base = mio_boot_reg_cfg.s.base << 16;
+			region_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (mio_boot_reg_cfg.s.en && base_ptr >= region_base
+				&& base_ptr < region_base + region_size) {
+				is_16bit = mio_boot_reg_cfg.s.width;
+				break;
+			}
+		}
+		if (cs >= 7) {
+			/* cs and cs + 1 are CS0 and CS1, both must be less than 8. */
+			goto no_cf;
+		}
+
+		if (!(base_ptr & 0xfffful)) {
+			/*
+			 * Boot loader signals availability of DMA (true_ide
+			 * mode) by setting low order bits of base_ptr to
+			 * zero.
+			 */
+
+			/* Asume that CS1 immediately follows. */
+			mio_boot_reg_cfg.u64 =
+				cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs + 1));
+			region1_base = mio_boot_reg_cfg.s.base << 16;
+			region1_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (!mio_boot_reg_cfg.s.en)
+				goto no_cf;
+			is_true_ide = true;
+
+		} else {
+			fdt_nop_property(initial_boot_params, cf, "cavium,true-ide");
+			fdt_nop_property(initial_boot_params, cf, "cavium,dma-engine-handle");
+			if (!is_16bit) {
+				__be32 width = cpu_to_be32(8);
+				fdt_setprop_inplace(initial_boot_params, cf,
+						"cavium,bus-width", &width, sizeof(width));
+			}
+		}
+		new_reg[0] = cpu_to_be32(cs);
+		new_reg[1] = cpu_to_be32(0);
+		new_reg[2] = cpu_to_be32(0x10000);
+		new_reg[3] = cpu_to_be32(cs + 1);
+		new_reg[4] = cpu_to_be32(0);
+		new_reg[5] = cpu_to_be32(0x10000);
+		fdt_setprop_inplace(initial_boot_params, cf,
+				    "reg",  new_reg, sizeof(new_reg));
+
+		bootbus = fdt_parent_offset(initial_boot_params, cf);
+		if (bootbus < 0)
+			goto no_cf;
+		ranges = fdt_getprop_w(initial_boot_params, bootbus, "ranges", &len);
+		if (!ranges || len < (5 * 8 * sizeof(__be32)))
+			goto no_cf;
+
+		ranges[(cs * 5) + 2] = cpu_to_be32(region_base >> 32);
+		ranges[(cs * 5) + 3] = cpu_to_be32(region_base & 0xffffffff);
+		ranges[(cs * 5) + 4] = cpu_to_be32(region_size);
+		if (is_true_ide) {
+			cs++;
+			ranges[(cs * 5) + 2] = cpu_to_be32(region1_base >> 32);
+			ranges[(cs * 5) + 3] = cpu_to_be32(region1_base & 0xffffffff);
+			ranges[(cs * 5) + 4] = cpu_to_be32(region1_size);
+		}
+		goto end_cf;
+no_cf:
+		fdt_nop_node(initial_boot_params, cf);
+
+end_cf:
+		;
+	}
+
+	/* 8 char LED */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "led0", NULL);
+	if (alias_prop) {
+		union cvmx_mio_boot_reg_cfgx mio_boot_reg_cfg;
+		unsigned long base_ptr, region_base, region_size;
+		int cs, bootbus;
+		__be32 new_reg[6];
+		__be32 *ranges;
+		int len;
+		int led = fdt_path_offset(initial_boot_params, alias_prop);
+
+		base_ptr = octeon_bootinfo->led_display_base_addr;
+		if (base_ptr == 0)
+			goto no_led;
+		/* Find CS0 region. */
+		for (cs = 0; cs < 8; cs++) {
+			mio_boot_reg_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs));
+			region_base = mio_boot_reg_cfg.s.base << 16;
+			region_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (mio_boot_reg_cfg.s.en && base_ptr >= region_base
+				&& base_ptr < region_base + region_size)
+				break;
+		}
+
+		if (cs > 7)
+			goto no_led;
+
+		new_reg[0] = cpu_to_be32(cs);
+		new_reg[1] = cpu_to_be32(0x20);
+		new_reg[2] = cpu_to_be32(0x20);
+		new_reg[3] = cpu_to_be32(cs);
+		new_reg[4] = cpu_to_be32(0);
+		new_reg[5] = cpu_to_be32(0x20);
+		fdt_setprop_inplace(initial_boot_params, led,
+				    "reg",  new_reg, sizeof(new_reg));
+
+		bootbus = fdt_parent_offset(initial_boot_params, led);
+		if (bootbus < 0)
+			goto no_led;
+		ranges = fdt_getprop_w(initial_boot_params, bootbus, "ranges", &len);
+		if (!ranges || len < (5 * 8 * sizeof(__be32)))
+			goto no_led;
+
+		ranges[(cs * 5) + 2] = cpu_to_be32(region_base >> 32);
+		ranges[(cs * 5) + 3] = cpu_to_be32(region_base & 0xffffffff);
+		ranges[(cs * 5) + 4] = cpu_to_be32(region_size);
+		goto end_led;
+
+no_led:
+		fdt_nop_node(initial_boot_params, led);
+end_led:
+		;
+	}
+
+	/* OHCI/UHCI USB */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "uctl", NULL);
+	if (alias_prop) {
+		int uctl = fdt_path_offset(initial_boot_params, alias_prop);
+
+		if (uctl >= 0 && (!OCTEON_IS_MODEL(OCTEON_CN6XXX) ||
+				  octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC2E)) {
+			pr_debug("Deleting uctl\n");
+			fdt_nop_node(initial_boot_params, uctl);
+			fdt_nop_property(initial_boot_params, aliases, "uctl");
+		} else if (octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC10E ||
+			   octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC4E) {
+			/* Missing "refclk-type" defaults to crystal. */
+			fdt_nop_property(initial_boot_params, uctl, "refclk-type");
+		}
+	}
+
+	return 0;
+}
+
+static int __init octeon_publish_devices(void)
+{
+	return of_platform_bus_probe(NULL, octeon_ids, NULL);
+}
+device_initcall(octeon_publish_devices);
+
 MODULE_AUTHOR("David Daney <ddaney@caviumnetworks.com>");
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Platform driver for Octeon SOC");

arch/mips/cavium-octeon/octeon_3xxx.dts

@@ -0,0 +1,571 @@
+/dts-v1/;
+/*
+ * OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.  Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+	compatible = "cavium,octeon-3860";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu: interrupt-controller@1070000000000 {
+			compatible = "cavium,octeon-3860-ciu";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 1)
+			 * 2) Bit within the register (0..63)
+			 */
+			#interrupt-cells = <2>;
+			reg = <0x10700 0x00000000 0x0 0x7000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pin connect to 16 consecutive CUI bits */
+			interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+				     <0 20>, <0 21>, <0 22>, <0 23>,
+				     <0 24>, <0 25>, <0 26>, <0 27>,
+				     <0 28>, <0 29>, <0 30>, <0 31>;
+		};
+
+		smi0: mdio@1180000001800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001800 0x0 0x40>;
+
+			phy0: ethernet-phy@0 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <0>;
+			};
+
+			phy1: ethernet-phy@1 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <1>;
+			};
+
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy5: ethernet-phy@5 {
+				reg = <5>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+
+			phy6: ethernet-phy@6 {
+				reg = <6>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy7: ethernet-phy@7 {
+				reg = <7>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy8: ethernet-phy@8 {
+				reg = <8>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy9: ethernet-phy@9 {
+				reg = <9>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000001900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001900 0x0 0x40>;
+
+			phy100: ethernet-phy@1 {
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy101: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy102: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy103: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <0 62>, <1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		mix1: ethernet@1070000100800 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <1>;
+			interrupts = <1 18>, < 1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy1>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy2>;
+					cavium,alt-phy-handle = <&phy100>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy3>;
+					cavium,alt-phy-handle = <&phy101>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy4>;
+					cavium,alt-phy-handle = <&phy102>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy5>;
+					cavium,alt-phy-handle = <&phy103>;
+				};
+				ethernet@4 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x4>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@5 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x5>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@6 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x6>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@7 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x7>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@8 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x8>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@9 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x9>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@a {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xa>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@b {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xb>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@c {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xc>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@d {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xd>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@e {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xe>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@f {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xf>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy6>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy7>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy8>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy9>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <0 45>;
+			clock-frequency = <100000>;
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <0 59>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 34>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 35>;
+		};
+
+		uart2: serial@1180000000400 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000400 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <1 16>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0x0 0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0x0 0x1d020000  0x10000>,
+				 <5 0  0x0 0x1d040000  0x10000>,
+				 <6 0  0x0 0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <20>;
+				cavium,t-ce   = <60>;
+				cavium,t-oe   = <60>;
+				cavium,t-we   = <45>;
+				cavium,t-rd-hld = <35>;
+				cavium,t-wr-hld = <45>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <0>;
+				cavium,t-page   = <35>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause  = <320>;
+				cavium,t-wait   = <320>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <30>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <270>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <70>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <0>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			cf0: compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		mix1 = &mix1;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uart2 = &uart2;
+		flash0 = &flash0;
+		cf0 = &cf0;
+		uctl = &uctl;
+		led0 = &led0;
+	};
+ };

arch/mips/cavium-octeon/octeon_68xx.dts

@@ -0,0 +1,625 @@
+/dts-v1/;
+/*
+ * OCTEON 68XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.  Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+	compatible = "cavium,octeon-6880";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu2>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu2: interrupt-controller@1070100000000 {
+			compatible = "cavium,octeon-6880-ciu2";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 7)
+			 * 2) Bit within the register (0..63)
+			 */
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x10701 0x00000000 0x0 0x4000000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pins connect to 16 consecutive CUI bits */
+			interrupts = <7 0>,  <7 1>,  <7 2>,  <7 3>,
+				     <7 4>,  <7 5>,  <7 6>,  <7 7>,
+				     <7 8>,  <7 9>,  <7 10>, <7 11>,
+				     <7 12>, <7 13>, <7 14>, <7 15>;
+		};
+
+		smi0: mdio@1180000003800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003800 0x0 0x40>;
+
+			phy0: ethernet-phy@6 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <6>;
+			};
+
+			phy1: ethernet-phy@1 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy2: ethernet-phy@2 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000003880 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003880 0x0 0x40>;
+
+			phy41: ethernet-phy@1 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy42: ethernet-phy@2 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy43: ethernet-phy@3 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy44: ethernet-phy@4 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi2: mdio@1180000003900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003900 0x0 0x40>;
+
+			phy21: ethernet-phy@1 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy22: ethernet-phy@2 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy23: ethernet-phy@3 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy24: ethernet-phy@4 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi3: mdio@1180000003980 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003980 0x0 0x40>;
+
+			phy11: ethernet-phy@1 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy12: ethernet-phy@2 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy13: ethernet-phy@3 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy14: ethernet-phy@4 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <6 40>, <6 32>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@4 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x4>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy1>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy2>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy3>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy4>;
+				};
+			};
+
+			interface@3 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x3>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy11>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy12>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy13>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy14>;
+				};
+			};
+
+			interface@2 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x2>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy21>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy22>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy23>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy24>;
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x1>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy41>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy42>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy43>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy44>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <3 32>;
+			clock-frequency = <100000>;
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <3 33>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 36>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 37>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0       0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0       0x1d020000  0x10000>,
+				 <5 0  0       0x1d040000  0x10000>,
+				 <6 0  0       0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <10>;
+				cavium,t-ce   = <50>;
+				cavium,t-oe   = <50>;
+				cavium,t-we   = <35>;
+				cavium,t-rd-hld = <25>;
+				cavium,t-wr-hld = <35>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <300>;
+				cavium,t-page   = <25>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause  = <320>;
+				cavium,t-wait   = <320>;
+				cavium,t-page   = <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <300>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <300>;
+				cavium,t-page   = <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <30>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause  = <0>;
+				cavium,t-wait   = <30>;
+				cavium,t-page   = <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages     = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "bootloader";
+					reg = <0 0x200000>;
+					read-only;
+				};
+				partition@200000 {
+					label = "kernel";
+					reg = <0x200000 0x200000>;
+				};
+				partition@400000 {
+					label = "cramfs";
+					reg = <0x400000 0x3fe000>;
+				};
+				partition@7fe000 {
+					label = "environment";
+					reg = <0x7fe000 0x2000>;
+					read-only;
+				};
+			};
+
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		smi2 = &smi2;
+		smi3 = &smi3;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uctl = &uctl;
+		led0 = &led0;
+		flash0 = &flash0;
+	};
+ };

arch/mips/cavium-octeon/serial.c

@@ -43,95 +43,67 @@ void octeon_serial_out(struct uart_port *up, int offset, int value)
 	cvmx_write_csr((uint64_t)(up->membase + (offset << 3)), (u8)value);
 }
 
-/*
- * Allocated in .bss, so it is all zeroed.
- */
-#define OCTEON_MAX_UARTS 3
-static struct plat_serial8250_port octeon_uart8250_data[OCTEON_MAX_UARTS + 1];
-static struct platform_device octeon_uart8250_device = {
-	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= octeon_uart8250_data,
-	},
-};
-
-static void __init octeon_uart_set_common(struct plat_serial8250_port *p)
+static int __devinit octeon_serial_probe(struct platform_device *pdev)
 {
-	p->flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
-	p->type = PORT_OCTEON;
-	p->iotype = UPIO_MEM;
-	p->regshift = 3;	/* I/O addresses are every 8 bytes */
+	int irq, res;
+	struct resource *res_mem;
+	struct uart_port port;
+
+	/* All adaptors have an irq.  */
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	memset(&port, 0, sizeof(port));
+
+	port.flags = ASYNC_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
+	port.type = PORT_OCTEON;
+	port.iotype = UPIO_MEM;
+	port.regshift = 3;
+	port.dev = &pdev->dev;
+
 	if (octeon_is_simulation())
 		/* Make simulator output fast*/
-		p->uartclk = 115200 * 16;
+		port.uartclk = 115200 * 16;
 	else
-		p->uartclk = octeon_get_io_clock_rate();
-	p->serial_in = octeon_serial_in;
-	p->serial_out = octeon_serial_out;
-}
+		port.uartclk = octeon_get_io_clock_rate();
 
-static int __init octeon_serial_init(void)
-{
-	int enable_uart0;
-	int enable_uart1;
-	int enable_uart2;
-	struct plat_serial8250_port *p;
-
-#ifdef CONFIG_CAVIUM_OCTEON_2ND_KERNEL
-	/*
-	 * If we are configured to run as the second of two kernels,
-	 * disable uart0 and enable uart1. Uart0 is owned by the first
-	 * kernel
-	 */
-	enable_uart0 = 0;
-	enable_uart1 = 1;
-#else
-	/*
-	 * We are configured for the first kernel. We'll enable uart0
-	 * if the bootloader told us to use 0, otherwise will enable
-	 * uart 1.
-	 */
-	enable_uart0 = (octeon_get_boot_uart() == 0);
-	enable_uart1 = (octeon_get_boot_uart() == 1);
-#ifdef CONFIG_KGDB
-	enable_uart1 = 1;
-#endif
-#endif
-
-	/* Right now CN52XX is the only chip with a third uart */
-	enable_uart2 = OCTEON_IS_MODEL(OCTEON_CN52XX);
-
-	p = octeon_uart8250_data;
-	if (enable_uart0) {
-		/* Add a ttyS device for hardware uart 0 */
-		octeon_uart_set_common(p);
-		p->membase = (void *) CVMX_MIO_UARTX_RBR(0);
-		p->mapbase = CVMX_MIO_UARTX_RBR(0) & ((1ull << 49) - 1);
-		p->irq = OCTEON_IRQ_UART0;
-		p++;
-	}
+	port.serial_in = octeon_serial_in;
+	port.serial_out = octeon_serial_out;
+	port.irq = irq;
 
-	if (enable_uart1) {
-		/* Add a ttyS device for hardware uart 1 */
-		octeon_uart_set_common(p);
-		p->membase = (void *) CVMX_MIO_UARTX_RBR(1);
-		p->mapbase = CVMX_MIO_UARTX_RBR(1) & ((1ull << 49) - 1);
-		p->irq = OCTEON_IRQ_UART1;
-		p++;
-	}
-	if (enable_uart2) {
-		/* Add a ttyS device for hardware uart 2 */
-		octeon_uart_set_common(p);
-		p->membase = (void *) CVMX_MIO_UART2_RBR;
-		p->mapbase = CVMX_MIO_UART2_RBR & ((1ull << 49) - 1);
-		p->irq = OCTEON_IRQ_UART2;
-		p++;
+	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res_mem == NULL) {
+		dev_err(&pdev->dev, "found no memory resource\n");
+		return -ENXIO;
 	}
+	port.mapbase = res_mem->start;
+	port.membase = ioremap(res_mem->start, resource_size(res_mem));
 
-	BUG_ON(p > &octeon_uart8250_data[OCTEON_MAX_UARTS]);
+	res = serial8250_register_port(&port);
 
-	return platform_device_register(&octeon_uart8250_device);
+	return res >= 0 ? 0 : res;
 }
 
-device_initcall(octeon_serial_init);
+static struct of_device_id octeon_serial_match[] = {
+	{
+		.compatible = "cavium,octeon-3860-uart",
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, octeon_serial_match);
+
+static struct platform_driver octeon_serial_driver = {
+	.probe		= octeon_serial_probe,
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= "octeon_serial",
+		.of_match_table = octeon_serial_match,
+	},
+};
+
+static int __init octeon_serial_init(void)
+{
+	return platform_driver_register(&octeon_serial_driver);
+}
+late_initcall(octeon_serial_init);

arch/mips/cavium-octeon/setup.c

@@ -21,6 +21,8 @@
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
 #include <linux/serial_8250.h>
+#include <linux/of_fdt.h>
+#include <linux/libfdt.h>
 
 #include <asm/processor.h>
 #include <asm/reboot.h>
@@ -775,3 +777,46 @@ void prom_free_prom_memory(void)
 	}
 #endif
 }
+
+int octeon_prune_device_tree(void);
+
+extern const char __dtb_octeon_3xxx_begin;
+extern const char __dtb_octeon_3xxx_end;
+extern const char __dtb_octeon_68xx_begin;
+extern const char __dtb_octeon_68xx_end;
+void __init device_tree_init(void)
+{
+	int dt_size;
+	struct boot_param_header *fdt;
+	bool do_prune;
+
+	if (octeon_bootinfo->minor_version >= 3 && octeon_bootinfo->fdt_addr) {
+		fdt = phys_to_virt(octeon_bootinfo->fdt_addr);
+		if (fdt_check_header(fdt))
+			panic("Corrupt Device Tree passed to kernel.");
+		dt_size = be32_to_cpu(fdt->totalsize);
+		do_prune = false;
+	} else if (OCTEON_IS_MODEL(OCTEON_CN68XX)) {
+		fdt = (struct boot_param_header *)&__dtb_octeon_68xx_begin;
+		dt_size = &__dtb_octeon_68xx_end - &__dtb_octeon_68xx_begin;
+		do_prune = true;
+	} else {
+		fdt = (struct boot_param_header *)&__dtb_octeon_3xxx_begin;
+		dt_size = &__dtb_octeon_3xxx_end - &__dtb_octeon_3xxx_begin;
+		do_prune = true;
+	}
+
+	/* Copy the default tree from init memory. */
+	initial_boot_params = early_init_dt_alloc_memory_arch(dt_size, 8);
+	if (initial_boot_params == NULL)
+		panic("Could not allocate initial_boot_params\n");
+	memcpy(initial_boot_params, fdt, dt_size);
+
+	if (do_prune) {
+		octeon_prune_device_tree();
+		pr_info("Using internal Device Tree.\n");
+	} else {
+		pr_info("Using passed Device Tree.\n");
+	}
+	unflatten_device_tree();
+}

arch/mips/configs/ls1b_defconfig

@@ -0,0 +1,109 @@
+CONFIG_MACH_LOONGSON1=y
+CONFIG_PREEMPT=y
+# CONFIG_SECCOMP is not set
+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_NAMESPACES=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_EXPERT=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SUSPEND is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_SCSI=m
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_DA=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=8
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_USB_HID=m
+CONFIG_HID_GENERIC=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_STORAGE=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_LOONGSON1=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
+# CONFIG_EARLY_PRINTK is not set

arch/mips/configs/nlm_xlr_defconfig

@@ -367,6 +367,10 @@ CONFIG_SERIAL_8250_RSA=y
 CONFIG_HW_RANDOM=y
 CONFIG_HW_RANDOM_TIMERIOMEM=m
 CONFIG_RAW_DRIVER=m
+CONFIG_I2C=y
+CONFIG_I2C_XLR=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1374=y
 # CONFIG_HWMON is not set
 # CONFIG_VGA_CONSOLE is not set
 # CONFIG_HID_SUPPORT is not set

arch/mips/dec/prom/memory.c

@@ -101,7 +101,7 @@ void __init prom_free_prom_memory(void)
 	 * the first page reserved for the exception handlers.
 	 */
 
-#if defined(CONFIG_DECLANCE) || defined(CONFIG_DECLANCE_MODULE)
+#if IS_ENABLED(CONFIG_DECLANCE)
 	/*
 	 * Leave 128 KB reserved for Lance memory for
 	 * IOASIC DECstations.

arch/mips/include/asm/cpu.h

@@ -197,6 +197,7 @@
 #define PRID_REV_VR4181A	0x0070	/* Same as VR4122 */
 #define PRID_REV_VR4130		0x0080
 #define PRID_REV_34K_V1_0_2	0x0022
+#define PRID_REV_LOONGSON1B	0x0020
 #define PRID_REV_LOONGSON2E	0x0002
 #define PRID_REV_LOONGSON2F	0x0003
 
@@ -261,7 +262,7 @@ enum cpu_type_enum {
 	 */
 	CPU_4KC, CPU_4KEC, CPU_4KSC, CPU_24K, CPU_34K, CPU_1004K, CPU_74K,
 	CPU_ALCHEMY, CPU_PR4450, CPU_BMIPS32, CPU_BMIPS3300, CPU_BMIPS4350,
-	CPU_BMIPS4380, CPU_BMIPS5000, CPU_JZRISC, CPU_M14KC,
+	CPU_BMIPS4380, CPU_BMIPS5000, CPU_JZRISC, CPU_LOONGSON1, CPU_M14KC,
 
 	/*
 	 * MIPS64 class processors

arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h

@@ -9,6 +9,7 @@
  * compile time if only one CPU support is enabled (idea stolen from
  * arm mach-types)
  */
+#define BCM6328_CPU_ID		0x6328
 #define BCM6338_CPU_ID		0x6338
 #define BCM6345_CPU_ID		0x6345
 #define BCM6348_CPU_ID		0x6348
@@ -20,6 +21,19 @@ u16 __bcm63xx_get_cpu_id(void);
 u16 bcm63xx_get_cpu_rev(void);
 unsigned int bcm63xx_get_cpu_freq(void);
 
+#ifdef CONFIG_BCM63XX_CPU_6328
+# ifdef bcm63xx_get_cpu_id
+#  undef bcm63xx_get_cpu_id
+#  define bcm63xx_get_cpu_id()	__bcm63xx_get_cpu_id()
+#  define BCMCPU_RUNTIME_DETECT
+# else
+#  define bcm63xx_get_cpu_id()	BCM6328_CPU_ID
+# endif
+# define BCMCPU_IS_6328()	(bcm63xx_get_cpu_id() == BCM6328_CPU_ID)
+#else
+# define BCMCPU_IS_6328()	(0)
+#endif
+
 #ifdef CONFIG_BCM63XX_CPU_6338
 # ifdef bcm63xx_get_cpu_id
 #  undef bcm63xx_get_cpu_id
@@ -102,13 +116,13 @@ enum bcm63xx_regs_set {
 	RSET_UART1,
 	RSET_GPIO,
 	RSET_SPI,
-	RSET_SPI2,
 	RSET_UDC0,
 	RSET_OHCI0,
 	RSET_OHCI_PRIV,
 	RSET_USBH_PRIV,
 	RSET_MPI,
 	RSET_PCMCIA,
+	RSET_PCIE,
 	RSET_DSL,
 	RSET_ENET0,
 	RSET_ENET1,
@@ -130,11 +144,17 @@ enum bcm63xx_regs_set {
 	RSET_PCMDMA,
 	RSET_PCMDMAC,
 	RSET_PCMDMAS,
+	RSET_RNG,
+	RSET_MISC
 };
 
 #define RSET_DSL_LMEM_SIZE		(64 * 1024 * 4)
 #define RSET_DSL_SIZE			4096
 #define RSET_WDT_SIZE			12
+#define BCM_6338_RSET_SPI_SIZE		64
+#define BCM_6348_RSET_SPI_SIZE		64
+#define BCM_6358_RSET_SPI_SIZE		1804
+#define BCM_6368_RSET_SPI_SIZE		1804
 #define RSET_ENET_SIZE			2048
 #define RSET_ENETDMA_SIZE		2048
 #define RSET_ENETSW_SIZE		65536
@@ -149,7 +169,52 @@ enum bcm63xx_regs_set {
 #define RSET_XTMDMA_SIZE		256
 #define RSET_XTMDMAC_SIZE(chans)	(16 * (chans))
 #define RSET_XTMDMAS_SIZE(chans)	(16 * (chans))
+#define RSET_RNG_SIZE			20
 
+/*
+ * 6328 register sets base address
+ */
+#define BCM_6328_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_6328_PERF_BASE		(0xb0000000)
+#define BCM_6328_TIMER_BASE		(0xb0000040)
+#define BCM_6328_WDT_BASE		(0xb000005c)
+#define BCM_6328_UART0_BASE             (0xb0000100)
+#define BCM_6328_UART1_BASE		(0xb0000120)
+#define BCM_6328_GPIO_BASE		(0xb0000080)
+#define BCM_6328_SPI_BASE		(0xdeadbeef)
+#define BCM_6328_UDC0_BASE		(0xdeadbeef)
+#define BCM_6328_USBDMA_BASE		(0xdeadbeef)
+#define BCM_6328_OHCI0_BASE		(0xdeadbeef)
+#define BCM_6328_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6328_USBH_PRIV_BASE		(0xdeadbeef)
+#define BCM_6328_MPI_BASE		(0xdeadbeef)
+#define BCM_6328_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6328_PCIE_BASE		(0xb0e40000)
+#define BCM_6328_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_6328_DSL_BASE		(0xb0001900)
+#define BCM_6328_UBUS_BASE		(0xdeadbeef)
+#define BCM_6328_ENET0_BASE		(0xdeadbeef)
+#define BCM_6328_ENET1_BASE		(0xdeadbeef)
+#define BCM_6328_ENETDMA_BASE		(0xb000d800)
+#define BCM_6328_ENETDMAC_BASE		(0xb000da00)
+#define BCM_6328_ENETDMAS_BASE		(0xb000dc00)
+#define BCM_6328_ENETSW_BASE		(0xb0e00000)
+#define BCM_6328_EHCI0_BASE		(0x10002500)
+#define BCM_6328_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6328_MEMC_BASE		(0xdeadbeef)
+#define BCM_6328_DDR_BASE		(0xb0003000)
+#define BCM_6328_M2M_BASE		(0xdeadbeef)
+#define BCM_6328_ATM_BASE		(0xdeadbeef)
+#define BCM_6328_XTM_BASE		(0xdeadbeef)
+#define BCM_6328_XTMDMA_BASE		(0xb000b800)
+#define BCM_6328_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6328_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6328_PCM_BASE		(0xb000a800)
+#define BCM_6328_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6328_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6328_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6328_RNG_BASE		(0xdeadbeef)
+#define BCM_6328_MISC_BASE		(0xb0001800)
 /*
  * 6338 register sets base address
  */
@@ -162,7 +227,6 @@ enum bcm63xx_regs_set {
 #define BCM_6338_UART1_BASE		(0xdeadbeef)
 #define BCM_6338_GPIO_BASE		(0xfffe0400)
 #define BCM_6338_SPI_BASE		(0xfffe0c00)
-#define BCM_6338_SPI2_BASE		(0xdeadbeef)
 #define BCM_6338_UDC0_BASE		(0xdeadbeef)
 #define BCM_6338_USBDMA_BASE		(0xfffe2400)
 #define BCM_6338_OHCI0_BASE		(0xdeadbeef)
@@ -170,6 +234,7 @@ enum bcm63xx_regs_set {
 #define BCM_6338_USBH_PRIV_BASE		(0xdeadbeef)
 #define BCM_6338_MPI_BASE		(0xfffe3160)
 #define BCM_6338_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6338_PCIE_BASE		(0xdeadbeef)
 #define BCM_6338_SDRAM_REGS_BASE	(0xfffe3100)
 #define BCM_6338_DSL_BASE		(0xfffe1000)
 #define BCM_6338_UBUS_BASE		(0xdeadbeef)
@@ -193,6 +258,8 @@ enum bcm63xx_regs_set {
 #define BCM_6338_PCMDMA_BASE		(0xdeadbeef)
 #define BCM_6338_PCMDMAC_BASE		(0xdeadbeef)
 #define BCM_6338_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6338_RNG_BASE		(0xdeadbeef)
+#define BCM_6338_MISC_BASE		(0xdeadbeef)
 
 /*
  * 6345 register sets base address
@@ -206,7 +273,6 @@ enum bcm63xx_regs_set {
 #define BCM_6345_UART1_BASE		(0xdeadbeef)
 #define BCM_6345_GPIO_BASE		(0xfffe0400)
 #define BCM_6345_SPI_BASE		(0xdeadbeef)
-#define BCM_6345_SPI2_BASE		(0xdeadbeef)
 #define BCM_6345_UDC0_BASE		(0xdeadbeef)
 #define BCM_6345_USBDMA_BASE		(0xfffe2800)
 #define BCM_6345_ENET0_BASE		(0xfffe1800)
@@ -216,6 +282,7 @@ enum bcm63xx_regs_set {
 #define BCM_6345_ENETSW_BASE		(0xdeadbeef)
 #define BCM_6345_PCMCIA_BASE		(0xfffe2028)
 #define BCM_6345_MPI_BASE		(0xfffe2000)
+#define BCM_6345_PCIE_BASE		(0xdeadbeef)
 #define BCM_6345_OHCI0_BASE		(0xfffe2100)
 #define BCM_6345_OHCI_PRIV_BASE		(0xfffe2200)
 #define BCM_6345_USBH_PRIV_BASE		(0xdeadbeef)
@@ -237,6 +304,8 @@ enum bcm63xx_regs_set {
 #define BCM_6345_PCMDMA_BASE		(0xdeadbeef)
 #define BCM_6345_PCMDMAC_BASE		(0xdeadbeef)
 #define BCM_6345_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6345_RNG_BASE		(0xdeadbeef)
+#define BCM_6345_MISC_BASE		(0xdeadbeef)
 
 /*
  * 6348 register sets base address
@@ -249,13 +318,13 @@ enum bcm63xx_regs_set {
 #define BCM_6348_UART1_BASE		(0xdeadbeef)
 #define BCM_6348_GPIO_BASE		(0xfffe0400)
 #define BCM_6348_SPI_BASE		(0xfffe0c00)
-#define BCM_6348_SPI2_BASE		(0xdeadbeef)
 #define BCM_6348_UDC0_BASE		(0xfffe1000)
 #define BCM_6348_OHCI0_BASE		(0xfffe1b00)
 #define BCM_6348_OHCI_PRIV_BASE		(0xfffe1c00)
 #define BCM_6348_USBH_PRIV_BASE		(0xdeadbeef)
 #define BCM_6348_MPI_BASE		(0xfffe2000)
 #define BCM_6348_PCMCIA_BASE		(0xfffe2054)
+#define BCM_6348_PCIE_BASE		(0xdeadbeef)
 #define BCM_6348_SDRAM_REGS_BASE	(0xfffe2300)
 #define BCM_6348_M2M_BASE		(0xfffe2800)
 #define BCM_6348_DSL_BASE		(0xfffe3000)
@@ -278,6 +347,8 @@ enum bcm63xx_regs_set {
 #define BCM_6348_PCMDMA_BASE		(0xdeadbeef)
 #define BCM_6348_PCMDMAC_BASE		(0xdeadbeef)
 #define BCM_6348_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6348_RNG_BASE		(0xdeadbeef)
+#define BCM_6348_MISC_BASE		(0xdeadbeef)
 
 /*
  * 6358 register sets base address
@@ -289,14 +360,14 @@ enum bcm63xx_regs_set {
 #define BCM_6358_UART0_BASE		(0xfffe0100)
 #define BCM_6358_UART1_BASE		(0xfffe0120)
 #define BCM_6358_GPIO_BASE		(0xfffe0080)
-#define BCM_6358_SPI_BASE		(0xdeadbeef)
-#define BCM_6358_SPI2_BASE		(0xfffe0800)
+#define BCM_6358_SPI_BASE		(0xfffe0800)
 #define BCM_6358_UDC0_BASE		(0xfffe0800)
 #define BCM_6358_OHCI0_BASE		(0xfffe1400)
 #define BCM_6358_OHCI_PRIV_BASE		(0xdeadbeef)
 #define BCM_6358_USBH_PRIV_BASE		(0xfffe1500)
 #define BCM_6358_MPI_BASE		(0xfffe1000)
 #define BCM_6358_PCMCIA_BASE		(0xfffe1054)
+#define BCM_6358_PCIE_BASE		(0xdeadbeef)
 #define BCM_6358_SDRAM_REGS_BASE	(0xfffe2300)
 #define BCM_6358_M2M_BASE		(0xdeadbeef)
 #define BCM_6358_DSL_BASE		(0xfffe3000)
@@ -319,6 +390,8 @@ enum bcm63xx_regs_set {
 #define BCM_6358_PCMDMA_BASE		(0xfffe1800)
 #define BCM_6358_PCMDMAC_BASE		(0xfffe1900)
 #define BCM_6358_PCMDMAS_BASE		(0xfffe1a00)
+#define BCM_6358_RNG_BASE		(0xdeadbeef)
+#define BCM_6358_MISC_BASE		(0xdeadbeef)
 
 
 /*
@@ -331,14 +404,14 @@ enum bcm63xx_regs_set {
 #define BCM_6368_UART0_BASE		(0xb0000100)
 #define BCM_6368_UART1_BASE		(0xb0000120)
 #define BCM_6368_GPIO_BASE		(0xb0000080)
-#define BCM_6368_SPI_BASE		(0xdeadbeef)
-#define BCM_6368_SPI2_BASE		(0xb0000800)
+#define BCM_6368_SPI_BASE		(0xb0000800)
 #define BCM_6368_UDC0_BASE		(0xdeadbeef)
 #define BCM_6368_OHCI0_BASE		(0xb0001600)
 #define BCM_6368_OHCI_PRIV_BASE		(0xdeadbeef)
 #define BCM_6368_USBH_PRIV_BASE		(0xb0001700)
 #define BCM_6368_MPI_BASE		(0xb0001000)
 #define BCM_6368_PCMCIA_BASE		(0xb0001054)
+#define BCM_6368_PCIE_BASE		(0xdeadbeef)
 #define BCM_6368_SDRAM_REGS_BASE	(0xdeadbeef)
 #define BCM_6368_M2M_BASE		(0xdeadbeef)
 #define BCM_6368_DSL_BASE		(0xdeadbeef)
@@ -361,6 +434,8 @@ enum bcm63xx_regs_set {
 #define BCM_6368_PCMDMA_BASE		(0xb0005800)
 #define BCM_6368_PCMDMAC_BASE		(0xb0005a00)
 #define BCM_6368_PCMDMAS_BASE		(0xb0005c00)
+#define BCM_6368_RNG_BASE		(0xb0004180)
+#define BCM_6368_MISC_BASE		(0xdeadbeef)
 
 
 extern const unsigned long *bcm63xx_regs_base;
@@ -379,13 +454,13 @@ extern const unsigned long *bcm63xx_regs_base;
 	__GEN_RSET_BASE(__cpu, UART1)					\
 	__GEN_RSET_BASE(__cpu, GPIO)					\
 	__GEN_RSET_BASE(__cpu, SPI)					\
-	__GEN_RSET_BASE(__cpu, SPI2)					\
 	__GEN_RSET_BASE(__cpu, UDC0)					\
 	__GEN_RSET_BASE(__cpu, OHCI0)					\
 	__GEN_RSET_BASE(__cpu, OHCI_PRIV)				\
 	__GEN_RSET_BASE(__cpu, USBH_PRIV)				\
 	__GEN_RSET_BASE(__cpu, MPI)					\
 	__GEN_RSET_BASE(__cpu, PCMCIA)					\
+	__GEN_RSET_BASE(__cpu, PCIE)					\
 	__GEN_RSET_BASE(__cpu, DSL)					\
 	__GEN_RSET_BASE(__cpu, ENET0)					\
 	__GEN_RSET_BASE(__cpu, ENET1)					\
@@ -407,6 +482,8 @@ extern const unsigned long *bcm63xx_regs_base;
 	__GEN_RSET_BASE(__cpu, PCMDMA)					\
 	__GEN_RSET_BASE(__cpu, PCMDMAC)					\
 	__GEN_RSET_BASE(__cpu, PCMDMAS)					\
+	__GEN_RSET_BASE(__cpu, RNG)					\
+	__GEN_RSET_BASE(__cpu, MISC)					\
 	}
 
 #define __GEN_CPU_REGS_TABLE(__cpu)					\
@@ -418,13 +495,13 @@ extern const unsigned long *bcm63xx_regs_base;
 	[RSET_UART1]		= BCM_## __cpu ##_UART1_BASE,		\
 	[RSET_GPIO]		= BCM_## __cpu ##_GPIO_BASE,		\
 	[RSET_SPI]		= BCM_## __cpu ##_SPI_BASE,		\
-	[RSET_SPI2]		= BCM_## __cpu ##_SPI2_BASE,		\
 	[RSET_UDC0]		= BCM_## __cpu ##_UDC0_BASE,		\
 	[RSET_OHCI0]		= BCM_## __cpu ##_OHCI0_BASE,		\
 	[RSET_OHCI_PRIV]	= BCM_## __cpu ##_OHCI_PRIV_BASE,	\
 	[RSET_USBH_PRIV]	= BCM_## __cpu ##_USBH_PRIV_BASE,	\
 	[RSET_MPI]		= BCM_## __cpu ##_MPI_BASE,		\
 	[RSET_PCMCIA]		= BCM_## __cpu ##_PCMCIA_BASE,		\
+	[RSET_PCIE]		= BCM_## __cpu ##_PCIE_BASE,		\
 	[RSET_DSL]		= BCM_## __cpu ##_DSL_BASE,		\
 	[RSET_ENET0]		= BCM_## __cpu ##_ENET0_BASE,		\
 	[RSET_ENET1]		= BCM_## __cpu ##_ENET1_BASE,		\
@@ -446,6 +523,8 @@ extern const unsigned long *bcm63xx_regs_base;
 	[RSET_PCMDMA]		= BCM_## __cpu ##_PCMDMA_BASE,		\
 	[RSET_PCMDMAC]		= BCM_## __cpu ##_PCMDMAC_BASE,		\
 	[RSET_PCMDMAS]		= BCM_## __cpu ##_PCMDMAS_BASE,		\
+	[RSET_RNG]		= BCM_## __cpu ##_RNG_BASE,		\
+	[RSET_MISC]		= BCM_## __cpu ##_MISC_BASE,		\
 
 
 static inline unsigned long bcm63xx_regset_address(enum bcm63xx_regs_set set)
@@ -453,6 +532,9 @@ static inline unsigned long bcm63xx_regset_address(enum bcm63xx_regs_set set)
 #ifdef BCMCPU_RUNTIME_DETECT
 	return bcm63xx_regs_base[set];
 #else
+#ifdef CONFIG_BCM63XX_CPU_6328
+	__GEN_RSET(6328)
+#endif
 #ifdef CONFIG_BCM63XX_CPU_6338
 	__GEN_RSET(6338)
 #endif
@@ -478,6 +560,7 @@ static inline unsigned long bcm63xx_regset_address(enum bcm63xx_regs_set set)
  */
 enum bcm63xx_irq {
 	IRQ_TIMER = 0,
+	IRQ_SPI,
 	IRQ_UART0,
 	IRQ_UART1,
 	IRQ_DSL,
@@ -505,10 +588,52 @@ enum bcm63xx_irq {
 	IRQ_XTM_DMA0,
 };
 
+/*
+ * 6328 irqs
+ */
+#define BCM_6328_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+
+#define BCM_6328_TIMER_IRQ		(IRQ_INTERNAL_BASE + 31)
+#define BCM_6328_SPI_IRQ		0
+#define BCM_6328_UART0_IRQ		(IRQ_INTERNAL_BASE + 28)
+#define BCM_6328_UART1_IRQ		(BCM_6328_HIGH_IRQ_BASE + 7)
+#define BCM_6328_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6328_UDC0_IRQ		0
+#define BCM_6328_ENET0_IRQ		0
+#define BCM_6328_ENET1_IRQ		0
+#define BCM_6328_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6328_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6328_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
+#define BCM_6328_PCMCIA_IRQ		0
+#define BCM_6328_ENET0_RXDMA_IRQ	0
+#define BCM_6328_ENET0_TXDMA_IRQ	0
+#define BCM_6328_ENET1_RXDMA_IRQ	0
+#define BCM_6328_ENET1_TXDMA_IRQ	0
+#define BCM_6328_PCI_IRQ		(IRQ_INTERNAL_BASE + 23)
+#define BCM_6328_ATM_IRQ		0
+#define BCM_6328_ENETSW_RXDMA0_IRQ	(BCM_6328_HIGH_IRQ_BASE + 0)
+#define BCM_6328_ENETSW_RXDMA1_IRQ	(BCM_6328_HIGH_IRQ_BASE + 1)
+#define BCM_6328_ENETSW_RXDMA2_IRQ	(BCM_6328_HIGH_IRQ_BASE + 2)
+#define BCM_6328_ENETSW_RXDMA3_IRQ	(BCM_6328_HIGH_IRQ_BASE + 3)
+#define BCM_6328_ENETSW_TXDMA0_IRQ	(BCM_6328_HIGH_IRQ_BASE + 4)
+#define BCM_6328_ENETSW_TXDMA1_IRQ	(BCM_6328_HIGH_IRQ_BASE + 5)
+#define BCM_6328_ENETSW_TXDMA2_IRQ	(BCM_6328_HIGH_IRQ_BASE + 6)
+#define BCM_6328_ENETSW_TXDMA3_IRQ	(BCM_6328_HIGH_IRQ_BASE + 7)
+#define BCM_6328_XTM_IRQ		(BCM_6328_HIGH_IRQ_BASE + 31)
+#define BCM_6328_XTM_DMA0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 11)
+
+#define BCM_6328_PCM_DMA0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6328_PCM_DMA1_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6328_EXT_IRQ0		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6328_EXT_IRQ1		(IRQ_INTERNAL_BASE + 25)
+#define BCM_6328_EXT_IRQ2		(IRQ_INTERNAL_BASE + 26)
+#define BCM_6328_EXT_IRQ3		(IRQ_INTERNAL_BASE + 27)
+
 /*
  * 6338 irqs
  */
 #define BCM_6338_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6338_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
 #define BCM_6338_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
 #define BCM_6338_UART1_IRQ		0
 #define BCM_6338_DSL_IRQ		(IRQ_INTERNAL_BASE + 5)
@@ -539,6 +664,7 @@ enum bcm63xx_irq {
  * 6345 irqs
  */
 #define BCM_6345_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6345_SPI_IRQ		0
 #define BCM_6345_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
 #define BCM_6345_UART1_IRQ		0
 #define BCM_6345_DSL_IRQ		(IRQ_INTERNAL_BASE + 3)
@@ -569,6 +695,7 @@ enum bcm63xx_irq {
  * 6348 irqs
  */
 #define BCM_6348_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6348_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
 #define BCM_6348_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
 #define BCM_6348_UART1_IRQ		0
 #define BCM_6348_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
@@ -599,6 +726,7 @@ enum bcm63xx_irq {
  * 6358 irqs
  */
 #define BCM_6358_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6358_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
 #define BCM_6358_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
 #define BCM_6358_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
 #define BCM_6358_DSL_IRQ		(IRQ_INTERNAL_BASE + 29)
@@ -638,6 +766,7 @@ enum bcm63xx_irq {
 #define BCM_6368_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
 
 #define BCM_6368_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6368_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
 #define BCM_6368_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
 #define BCM_6368_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
 #define BCM_6368_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
@@ -677,6 +806,7 @@ extern const int *bcm63xx_irqs;
 
 #define __GEN_CPU_IRQ_TABLE(__cpu)					\
 	[IRQ_TIMER]		= BCM_## __cpu ##_TIMER_IRQ,		\
+	[IRQ_SPI]		= BCM_## __cpu ##_SPI_IRQ,		\
 	[IRQ_UART0]		= BCM_## __cpu ##_UART0_IRQ,		\
 	[IRQ_UART1]		= BCM_## __cpu ##_UART1_IRQ,		\
 	[IRQ_DSL]		= BCM_## __cpu ##_DSL_IRQ,		\

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h

@@ -0,0 +1,12 @@
+#ifndef __BCM63XX_FLASH_H
+#define __BCM63XX_FLASH_H
+
+enum {
+	BCM63XX_FLASH_TYPE_PARALLEL,
+	BCM63XX_FLASH_TYPE_SERIAL,
+	BCM63XX_FLASH_TYPE_NAND,
+};
+
+int __init bcm63xx_flash_register(void);
+
+#endif /* __BCM63XX_FLASH_H */

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h

@@ -0,0 +1,89 @@
+#ifndef BCM63XX_DEV_SPI_H
+#define BCM63XX_DEV_SPI_H
+
+#include <linux/types.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+int __init bcm63xx_spi_register(void);
+
+struct bcm63xx_spi_pdata {
+	unsigned int	fifo_size;
+	int		bus_num;
+	int		num_chipselect;
+	u32		speed_hz;
+};
+
+enum bcm63xx_regs_spi {
+	SPI_CMD,
+	SPI_INT_STATUS,
+	SPI_INT_MASK_ST,
+	SPI_INT_MASK,
+	SPI_ST,
+	SPI_CLK_CFG,
+	SPI_FILL_BYTE,
+	SPI_MSG_TAIL,
+	SPI_RX_TAIL,
+	SPI_MSG_CTL,
+	SPI_MSG_DATA,
+	SPI_RX_DATA,
+};
+
+#define __GEN_SPI_RSET_BASE(__cpu, __rset)				\
+	case SPI_## __rset:						\
+		return SPI_## __cpu ##_## __rset;
+
+#define __GEN_SPI_RSET(__cpu)						\
+	switch (reg) {							\
+	__GEN_SPI_RSET_BASE(__cpu, CMD)					\
+	__GEN_SPI_RSET_BASE(__cpu, INT_STATUS)				\
+	__GEN_SPI_RSET_BASE(__cpu, INT_MASK_ST)				\
+	__GEN_SPI_RSET_BASE(__cpu, INT_MASK)				\
+	__GEN_SPI_RSET_BASE(__cpu, ST)					\
+	__GEN_SPI_RSET_BASE(__cpu, CLK_CFG)				\
+	__GEN_SPI_RSET_BASE(__cpu, FILL_BYTE)				\
+	__GEN_SPI_RSET_BASE(__cpu, MSG_TAIL)				\
+	__GEN_SPI_RSET_BASE(__cpu, RX_TAIL)				\
+	__GEN_SPI_RSET_BASE(__cpu, MSG_CTL)				\
+	__GEN_SPI_RSET_BASE(__cpu, MSG_DATA)				\
+	__GEN_SPI_RSET_BASE(__cpu, RX_DATA)				\
+	}
+
+#define __GEN_SPI_REGS_TABLE(__cpu)					\
+	[SPI_CMD]		= SPI_## __cpu ##_CMD,			\
+	[SPI_INT_STATUS]	= SPI_## __cpu ##_INT_STATUS,		\
+	[SPI_INT_MASK_ST]	= SPI_## __cpu ##_INT_MASK_ST,		\
+	[SPI_INT_MASK]		= SPI_## __cpu ##_INT_MASK,		\
+	[SPI_ST]		= SPI_## __cpu ##_ST,			\
+	[SPI_CLK_CFG]		= SPI_## __cpu ##_CLK_CFG,		\
+	[SPI_FILL_BYTE]		= SPI_## __cpu ##_FILL_BYTE,		\
+	[SPI_MSG_TAIL]		= SPI_## __cpu ##_MSG_TAIL,		\
+	[SPI_RX_TAIL]		= SPI_## __cpu ##_RX_TAIL,		\
+	[SPI_MSG_CTL]		= SPI_## __cpu ##_MSG_CTL,		\
+	[SPI_MSG_DATA]		= SPI_## __cpu ##_MSG_DATA,		\
+	[SPI_RX_DATA]		= SPI_## __cpu ##_RX_DATA,
+
+static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
+{
+#ifdef BCMCPU_RUNTIME_DETECT
+	extern const unsigned long *bcm63xx_regs_spi;
+
+	return bcm63xx_regs_spi[reg];
+#else
+#ifdef CONFIG_BCM63XX_CPU_6338
+	__GEN_SPI_RSET(6338)
+#endif
+#ifdef CONFIG_BCM63XX_CPU_6348
+	__GEN_SPI_RSET(6348)
+#endif
+#ifdef CONFIG_BCM63XX_CPU_6358
+	__GEN_SPI_RSET(6358)
+#endif
+#ifdef CONFIG_BCM63XX_CPU_6368
+	__GEN_SPI_RSET(6368)
+#endif
+#endif
+	return 0;
+}
+
+#endif /* BCM63XX_DEV_SPI_H */

arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h

@@ -9,6 +9,8 @@ int __init bcm63xx_gpio_init(void);
 static inline unsigned long bcm63xx_gpio_count(void)
 {
 	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		return 32;
 	case BCM6358_CPU_ID:
 		return 40;
 	case BCM6338_CPU_ID:

arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h

@@ -40,6 +40,10 @@
 #define BCM_CB_MEM_END_PA		(BCM_CB_MEM_BASE_PA +		\
 					BCM_CB_MEM_SIZE - 1)
 
+#define BCM_PCIE_MEM_BASE_PA		0x10f00000
+#define BCM_PCIE_MEM_SIZE		(16 * 1024 * 1024)
+#define BCM_PCIE_MEM_END_PA		(BCM_PCIE_MEM_BASE_PA +		\
+					BCM_PCIE_MEM_SIZE - 1)
 
 /*
  * Internal registers are accessed through KSEG3
@@ -85,11 +89,15 @@
 #define bcm_mpi_writel(v, o)	bcm_rset_writel(RSET_MPI, (v), (o))
 #define bcm_pcmcia_readl(o)	bcm_rset_readl(RSET_PCMCIA, (o))
 #define bcm_pcmcia_writel(v, o)	bcm_rset_writel(RSET_PCMCIA, (v), (o))
+#define bcm_pcie_readl(o)	bcm_rset_readl(RSET_PCIE, (o))
+#define bcm_pcie_writel(v, o)	bcm_rset_writel(RSET_PCIE, (v), (o))
 #define bcm_sdram_readl(o)	bcm_rset_readl(RSET_SDRAM, (o))
 #define bcm_sdram_writel(v, o)	bcm_rset_writel(RSET_SDRAM, (v), (o))
 #define bcm_memc_readl(o)	bcm_rset_readl(RSET_MEMC, (o))
 #define bcm_memc_writel(v, o)	bcm_rset_writel(RSET_MEMC, (v), (o))
 #define bcm_ddr_readl(o)	bcm_rset_readl(RSET_DDR, (o))
 #define bcm_ddr_writel(v, o)	bcm_rset_writel(RSET_DDR, (v), (o))
+#define bcm_misc_readl(o)	bcm_rset_readl(RSET_MISC, (o))
+#define bcm_misc_writel(v, o)	bcm_rset_writel(RSET_MISC, (v), (o))
 
 #endif /* ! BCM63XX_IO_H_ */

arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h

@@ -15,6 +15,30 @@
 /* Clock Control register */
 #define PERF_CKCTL_REG			0x4
 
+#define CKCTL_6328_PHYMIPS_EN		(1 << 0)
+#define CKCTL_6328_ADSL_QPROC_EN	(1 << 1)
+#define CKCTL_6328_ADSL_AFE_EN		(1 << 2)
+#define CKCTL_6328_ADSL_EN		(1 << 3)
+#define CKCTL_6328_MIPS_EN		(1 << 4)
+#define CKCTL_6328_SAR_EN		(1 << 5)
+#define CKCTL_6328_PCM_EN		(1 << 6)
+#define CKCTL_6328_USBD_EN		(1 << 7)
+#define CKCTL_6328_USBH_EN		(1 << 8)
+#define CKCTL_6328_HSSPI_EN		(1 << 9)
+#define CKCTL_6328_PCIE_EN		(1 << 10)
+#define CKCTL_6328_ROBOSW_EN		(1 << 11)
+
+#define CKCTL_6328_ALL_SAFE_EN		(CKCTL_6328_PHYMIPS_EN |	\
+					CKCTL_6328_ADSL_QPROC_EN |	\
+					CKCTL_6328_ADSL_AFE_EN |	\
+					CKCTL_6328_ADSL_EN |		\
+					CKCTL_6328_SAR_EN  |		\
+					CKCTL_6328_PCM_EN  |		\
+					CKCTL_6328_USBD_EN |		\
+					CKCTL_6328_USBH_EN |		\
+					CKCTL_6328_ROBOSW_EN |		\
+					CKCTL_6328_PCIE_EN)
+
 #define CKCTL_6338_ADSLPHY_EN		(1 << 0)
 #define CKCTL_6338_MPI_EN		(1 << 1)
 #define CKCTL_6338_DRAM_EN		(1 << 2)
@@ -90,35 +114,36 @@
 #define CKCTL_6368_PHYMIPS_EN		(1 << 6)
 #define CKCTL_6368_SWPKT_USB_EN		(1 << 7)
 #define CKCTL_6368_SWPKT_SAR_EN		(1 << 8)
-#define CKCTL_6368_SPI_CLK_EN		(1 << 9)
-#define CKCTL_6368_USBD_CLK_EN		(1 << 10)
-#define CKCTL_6368_SAR_CLK_EN		(1 << 11)
-#define CKCTL_6368_ROBOSW_CLK_EN	(1 << 12)
-#define CKCTL_6368_UTOPIA_CLK_EN	(1 << 13)
-#define CKCTL_6368_PCM_CLK_EN		(1 << 14)
-#define CKCTL_6368_USBH_CLK_EN		(1 << 15)
+#define CKCTL_6368_SPI_EN		(1 << 9)
+#define CKCTL_6368_USBD_EN		(1 << 10)
+#define CKCTL_6368_SAR_EN		(1 << 11)
+#define CKCTL_6368_ROBOSW_EN		(1 << 12)
+#define CKCTL_6368_UTOPIA_EN		(1 << 13)
+#define CKCTL_6368_PCM_EN		(1 << 14)
+#define CKCTL_6368_USBH_EN		(1 << 15)
 #define CKCTL_6368_DISABLE_GLESS_EN	(1 << 16)
-#define CKCTL_6368_NAND_CLK_EN		(1 << 17)
-#define CKCTL_6368_IPSEC_CLK_EN		(1 << 18)
+#define CKCTL_6368_NAND_EN		(1 << 17)
+#define CKCTL_6368_IPSEC_EN		(1 << 18)
 
 #define CKCTL_6368_ALL_SAFE_EN		(CKCTL_6368_SWPKT_USB_EN |	\
 					CKCTL_6368_SWPKT_SAR_EN |	\
-					CKCTL_6368_SPI_CLK_EN |		\
-					CKCTL_6368_USBD_CLK_EN |	\
-					CKCTL_6368_SAR_CLK_EN |		\
-					CKCTL_6368_ROBOSW_CLK_EN |	\
-					CKCTL_6368_UTOPIA_CLK_EN |	\
-					CKCTL_6368_PCM_CLK_EN |		\
-					CKCTL_6368_USBH_CLK_EN |	\
+					CKCTL_6368_SPI_EN |		\
+					CKCTL_6368_USBD_EN |		\
+					CKCTL_6368_SAR_EN |		\
+					CKCTL_6368_ROBOSW_EN |		\
+					CKCTL_6368_UTOPIA_EN |		\
+					CKCTL_6368_PCM_EN |		\
+					CKCTL_6368_USBH_EN |		\
 					CKCTL_6368_DISABLE_GLESS_EN |	\
-					CKCTL_6368_NAND_CLK_EN |	\
-					CKCTL_6368_IPSEC_CLK_EN)
+					CKCTL_6368_NAND_EN |		\
+					CKCTL_6368_IPSEC_EN)
 
 /* System PLL Control register  */
 #define PERF_SYS_PLL_CTL_REG		0x8
 #define SYS_PLL_SOFT_RESET		0x1
 
 /* Interrupt Mask register */
+#define PERF_IRQMASK_6328_REG		0x20
 #define PERF_IRQMASK_6338_REG		0xc
 #define PERF_IRQMASK_6345_REG		0xc
 #define PERF_IRQMASK_6348_REG		0xc
@@ -126,6 +151,7 @@
 #define PERF_IRQMASK_6368_REG		0x20
 
 /* Interrupt Status register */
+#define PERF_IRQSTAT_6328_REG		0x28
 #define PERF_IRQSTAT_6338_REG		0x10
 #define PERF_IRQSTAT_6345_REG		0x10
 #define PERF_IRQSTAT_6348_REG		0x10
@@ -133,6 +159,7 @@
 #define PERF_IRQSTAT_6368_REG		0x28
 
 /* External Interrupt Configuration register */
+#define PERF_EXTIRQ_CFG_REG_6328	0x18
 #define PERF_EXTIRQ_CFG_REG_6338	0x14
 #define PERF_EXTIRQ_CFG_REG_6348	0x14
 #define PERF_EXTIRQ_CFG_REG_6358	0x14
@@ -162,8 +189,21 @@
 
 /* Soft Reset register */
 #define PERF_SOFTRESET_REG		0x28
+#define PERF_SOFTRESET_6328_REG		0x10
 #define PERF_SOFTRESET_6368_REG		0x10
 
+#define SOFTRESET_6328_SPI_MASK		(1 << 0)
+#define SOFTRESET_6328_EPHY_MASK	(1 << 1)
+#define SOFTRESET_6328_SAR_MASK		(1 << 2)
+#define SOFTRESET_6328_ENETSW_MASK	(1 << 3)
+#define SOFTRESET_6328_USBS_MASK	(1 << 4)
+#define SOFTRESET_6328_USBH_MASK	(1 << 5)
+#define SOFTRESET_6328_PCM_MASK		(1 << 6)
+#define SOFTRESET_6328_PCIE_CORE_MASK	(1 << 7)
+#define SOFTRESET_6328_PCIE_MASK	(1 << 8)
+#define SOFTRESET_6328_PCIE_EXT_MASK	(1 << 9)
+#define SOFTRESET_6328_PCIE_HARD_MASK	(1 << 10)
+
 #define SOFTRESET_6338_SPI_MASK		(1 << 0)
 #define SOFTRESET_6338_ENET_MASK	(1 << 2)
 #define SOFTRESET_6338_USBH_MASK	(1 << 3)
@@ -307,6 +347,8 @@
 /* Watchdog reset length register */
 #define WDT_RSTLEN_REG			0x8
 
+/* Watchdog soft reset register (BCM6328 only) */
+#define WDT_SOFTRESET_REG		0xc
 
 /*************************************************************************
  * _REG relative to RSET_UARTx
@@ -507,6 +549,15 @@
 #define GPIO_BASEMODE_6368_MASK		0x7
 /* those bits must be kept as read in gpio basemode register*/
 
+#define GPIO_STRAPBUS_REG		0x40
+#define STRAPBUS_6358_BOOT_SEL_PARALLEL	(1 << 1)
+#define STRAPBUS_6358_BOOT_SEL_SERIAL	(0 << 1)
+#define STRAPBUS_6368_BOOT_SEL_MASK	0x3
+#define STRAPBUS_6368_BOOT_SEL_NAND	0
+#define STRAPBUS_6368_BOOT_SEL_SERIAL	1
+#define STRAPBUS_6368_BOOT_SEL_PARALLEL	3
+
+
 /*************************************************************************
  * _REG relative to RSET_ENET
  *************************************************************************/
@@ -924,6 +975,8 @@
  * _REG relative to RSET_DDR
  *************************************************************************/
 
+#define DDR_CSEND_REG			0x8
+
 #define DDR_DMIPSPLLCFG_REG		0x18
 #define DMIPSPLLCFG_M1_SHIFT		0
 #define DMIPSPLLCFG_M1_MASK		(0xff << DMIPSPLLCFG_M1_SHIFT)
@@ -973,4 +1026,201 @@
 #define M2M_SRCID_REG(x)		((x) * 0x40 + 0x14)
 #define M2M_DSTID_REG(x)		((x) * 0x40 + 0x18)
 
+/*************************************************************************
+ * _REG relative to RSET_RNG
+ *************************************************************************/
+
+#define RNG_CTRL			0x00
+#define RNG_EN				(1 << 0)
+
+#define RNG_STAT			0x04
+#define RNG_AVAIL_MASK			(0xff000000)
+
+#define RNG_DATA			0x08
+#define RNG_THRES			0x0c
+#define RNG_MASK			0x10
+
+/*************************************************************************
+ * _REG relative to RSET_SPI
+ *************************************************************************/
+
+/* BCM 6338 SPI core */
+#define SPI_6338_CMD			0x00	/* 16-bits register */
+#define SPI_6338_INT_STATUS		0x02
+#define SPI_6338_INT_MASK_ST		0x03
+#define SPI_6338_INT_MASK		0x04
+#define SPI_6338_ST			0x05
+#define SPI_6338_CLK_CFG		0x06
+#define SPI_6338_FILL_BYTE		0x07
+#define SPI_6338_MSG_TAIL		0x09
+#define SPI_6338_RX_TAIL		0x0b
+#define SPI_6338_MSG_CTL		0x40
+#define SPI_6338_MSG_DATA		0x41
+#define SPI_6338_MSG_DATA_SIZE		0x3f
+#define SPI_6338_RX_DATA		0x80
+#define SPI_6338_RX_DATA_SIZE		0x3f
+
+/* BCM 6348 SPI core */
+#define SPI_6348_CMD			0x00	/* 16-bits register */
+#define SPI_6348_INT_STATUS		0x02
+#define SPI_6348_INT_MASK_ST		0x03
+#define SPI_6348_INT_MASK		0x04
+#define SPI_6348_ST			0x05
+#define SPI_6348_CLK_CFG		0x06
+#define SPI_6348_FILL_BYTE		0x07
+#define SPI_6348_MSG_TAIL		0x09
+#define SPI_6348_RX_TAIL		0x0b
+#define SPI_6348_MSG_CTL		0x40
+#define SPI_6348_MSG_DATA		0x41
+#define SPI_6348_MSG_DATA_SIZE		0x3f
+#define SPI_6348_RX_DATA		0x80
+#define SPI_6348_RX_DATA_SIZE		0x3f
+
+/* BCM 6358 SPI core */
+#define SPI_6358_MSG_CTL		0x00	/* 16-bits register */
+#define SPI_6358_MSG_DATA		0x02
+#define SPI_6358_MSG_DATA_SIZE		0x21e
+#define SPI_6358_RX_DATA		0x400
+#define SPI_6358_RX_DATA_SIZE		0x220
+#define SPI_6358_CMD			0x700	/* 16-bits register */
+#define SPI_6358_INT_STATUS		0x702
+#define SPI_6358_INT_MASK_ST		0x703
+#define SPI_6358_INT_MASK		0x704
+#define SPI_6358_ST			0x705
+#define SPI_6358_CLK_CFG		0x706
+#define SPI_6358_FILL_BYTE		0x707
+#define SPI_6358_MSG_TAIL		0x709
+#define SPI_6358_RX_TAIL		0x70B
+
+/* BCM 6358 SPI core */
+#define SPI_6368_MSG_CTL		0x00	/* 16-bits register */
+#define SPI_6368_MSG_DATA		0x02
+#define SPI_6368_MSG_DATA_SIZE		0x21e
+#define SPI_6368_RX_DATA		0x400
+#define SPI_6368_RX_DATA_SIZE		0x220
+#define SPI_6368_CMD			0x700	/* 16-bits register */
+#define SPI_6368_INT_STATUS		0x702
+#define SPI_6368_INT_MASK_ST		0x703
+#define SPI_6368_INT_MASK		0x704
+#define SPI_6368_ST			0x705
+#define SPI_6368_CLK_CFG		0x706
+#define SPI_6368_FILL_BYTE		0x707
+#define SPI_6368_MSG_TAIL		0x709
+#define SPI_6368_RX_TAIL		0x70B
+
+/* Shared SPI definitions */
+
+/* Message configuration */
+#define SPI_FD_RW			0x00
+#define SPI_HD_W			0x01
+#define SPI_HD_R			0x02
+#define SPI_BYTE_CNT_SHIFT		0
+#define SPI_MSG_TYPE_SHIFT		14
+
+/* Command */
+#define SPI_CMD_NOOP			0x00
+#define SPI_CMD_SOFT_RESET		0x01
+#define SPI_CMD_HARD_RESET		0x02
+#define SPI_CMD_START_IMMEDIATE		0x03
+#define SPI_CMD_COMMAND_SHIFT		0
+#define SPI_CMD_COMMAND_MASK		0x000f
+#define SPI_CMD_DEVICE_ID_SHIFT		4
+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT	8
+#define SPI_CMD_ONE_BYTE_SHIFT		11
+#define SPI_CMD_ONE_WIRE_SHIFT		12
+#define SPI_DEV_ID_0			0
+#define SPI_DEV_ID_1			1
+#define SPI_DEV_ID_2			2
+#define SPI_DEV_ID_3			3
+
+/* Interrupt mask */
+#define SPI_INTR_CMD_DONE		0x01
+#define SPI_INTR_RX_OVERFLOW		0x02
+#define SPI_INTR_TX_UNDERFLOW		0x04
+#define SPI_INTR_TX_OVERFLOW		0x08
+#define SPI_INTR_RX_UNDERFLOW		0x10
+#define SPI_INTR_CLEAR_ALL		0x1f
+
+/* Status */
+#define SPI_RX_EMPTY			0x02
+#define SPI_CMD_BUSY			0x04
+#define SPI_SERIAL_BUSY			0x08
+
+/* Clock configuration */
+#define SPI_CLK_20MHZ			0x00
+#define SPI_CLK_0_391MHZ		0x01
+#define SPI_CLK_0_781MHZ		0x02 /* default */
+#define SPI_CLK_1_563MHZ		0x03
+#define SPI_CLK_3_125MHZ		0x04
+#define SPI_CLK_6_250MHZ		0x05
+#define SPI_CLK_12_50MHZ		0x06
+#define SPI_CLK_MASK			0x07
+#define SPI_SSOFFTIME_MASK		0x38
+#define SPI_SSOFFTIME_SHIFT		3
+#define SPI_BYTE_SWAP			0x80
+
+/*************************************************************************
+ * _REG relative to RSET_MISC
+ *************************************************************************/
+#define MISC_SERDES_CTRL_REG		0x0
+#define SERDES_PCIE_EN			(1 << 0)
+#define SERDES_PCIE_EXD_EN		(1 << 15)
+
+#define MISC_STRAPBUS_6328_REG		0x240
+#define STRAPBUS_6328_FCVO_SHIFT	7
+#define STRAPBUS_6328_FCVO_MASK		(0x1f << STRAPBUS_6328_FCVO_SHIFT)
+#define STRAPBUS_6328_BOOT_SEL_SERIAL	(1 << 28)
+#define STRAPBUS_6328_BOOT_SEL_NAND	(0 << 28)
+
+/*************************************************************************
+ * _REG relative to RSET_PCIE
+ *************************************************************************/
+
+#define PCIE_CONFIG2_REG		0x408
+#define CONFIG2_BAR1_SIZE_EN		1
+#define CONFIG2_BAR1_SIZE_MASK		0xf
+
+#define PCIE_IDVAL3_REG			0x43c
+#define IDVAL3_CLASS_CODE_MASK		0xffffff
+#define IDVAL3_SUBCLASS_SHIFT		8
+#define IDVAL3_CLASS_SHIFT		16
+
+#define PCIE_DLSTATUS_REG		0x1048
+#define DLSTATUS_PHYLINKUP		(1 << 13)
+
+#define PCIE_BRIDGE_OPT1_REG		0x2820
+#define OPT1_RD_BE_OPT_EN		(1 << 7)
+#define OPT1_RD_REPLY_BE_FIX_EN		(1 << 9)
+#define OPT1_PCIE_BRIDGE_HOLE_DET_EN	(1 << 11)
+#define OPT1_L1_INT_STATUS_MASK_POL	(1 << 12)
+
+#define PCIE_BRIDGE_OPT2_REG		0x2824
+#define OPT2_UBUS_UR_DECODE_DIS		(1 << 2)
+#define OPT2_TX_CREDIT_CHK_EN		(1 << 4)
+#define OPT2_CFG_TYPE1_BD_SEL		(1 << 7)
+#define OPT2_CFG_TYPE1_BUS_NO_SHIFT	16
+#define OPT2_CFG_TYPE1_BUS_NO_MASK	(0xff << OPT2_CFG_TYPE1_BUS_NO_SHIFT)
+
+#define PCIE_BRIDGE_BAR0_BASEMASK_REG	0x2828
+#define PCIE_BRIDGE_BAR1_BASEMASK_REG	0x2830
+#define BASEMASK_REMAP_EN		(1 << 0)
+#define BASEMASK_SWAP_EN		(1 << 1)
+#define BASEMASK_MASK_SHIFT		4
+#define BASEMASK_MASK_MASK		(0xfff << BASEMASK_MASK_SHIFT)
+#define BASEMASK_BASE_SHIFT		20
+#define BASEMASK_BASE_MASK		(0xfff << BASEMASK_BASE_SHIFT)
+
+#define PCIE_BRIDGE_BAR0_REBASE_ADDR_REG 0x282c
+#define PCIE_BRIDGE_BAR1_REBASE_ADDR_REG 0x2834
+#define REBASE_ADDR_BASE_SHIFT		20
+#define REBASE_ADDR_BASE_MASK		(0xfff << REBASE_ADDR_BASE_SHIFT)
+
+#define PCIE_BRIDGE_RC_INT_MASK_REG	0x2854
+#define PCIE_RC_INT_A			(1 << 0)
+#define PCIE_RC_INT_B			(1 << 1)
+#define PCIE_RC_INT_C			(1 << 2)
+#define PCIE_RC_INT_D			(1 << 3)
+
+#define PCIE_DEVICE_OFFSET		0x8000
+
 #endif /* BCM63XX_REGS_H_ */

arch/mips/include/asm/mach-bcm63xx/ioremap.h

@@ -18,6 +18,7 @@ static inline int is_bcm63xx_internal_registers(phys_t offset)
 		if (offset >= 0xfff00000)
 			return 1;
 		break;
+	case BCM6328_CPU_ID:
 	case BCM6368_CPU_ID:
 		if (offset >= 0xb0000000 && offset < 0xb1000000)
 			return 1;

arch/mips/include/asm/mach-cavium-octeon/irq.h

@@ -41,61 +41,26 @@ enum octeon_irq {
 	OCTEON_IRQ_TWSI,
 	OCTEON_IRQ_TWSI2,
 	OCTEON_IRQ_RML,
-	OCTEON_IRQ_TRACE0,
-	OCTEON_IRQ_GMX_DRP0 = OCTEON_IRQ_TRACE0 + 4,
-	OCTEON_IRQ_IPD_DRP = OCTEON_IRQ_GMX_DRP0 + 5,
-	OCTEON_IRQ_KEY_ZERO,
 	OCTEON_IRQ_TIMER0,
 	OCTEON_IRQ_TIMER1,
 	OCTEON_IRQ_TIMER2,
 	OCTEON_IRQ_TIMER3,
 	OCTEON_IRQ_USB0,
 	OCTEON_IRQ_USB1,
-	OCTEON_IRQ_PCM,
-	OCTEON_IRQ_MPI,
-	OCTEON_IRQ_POWIQ,
-	OCTEON_IRQ_IPDPPTHR,
 	OCTEON_IRQ_MII0,
 	OCTEON_IRQ_MII1,
 	OCTEON_IRQ_BOOTDMA,
-
-	OCTEON_IRQ_NAND,
-	OCTEON_IRQ_MIO,		/* Summary of MIO_BOOT_ERR */
-	OCTEON_IRQ_IOB,		/* Summary of IOB_INT_SUM */
-	OCTEON_IRQ_FPA,		/* Summary of FPA_INT_SUM */
-	OCTEON_IRQ_POW,		/* Summary of POW_ECC_ERR */
-	OCTEON_IRQ_L2C,		/* Summary of L2C_INT_STAT */
-	OCTEON_IRQ_IPD,		/* Summary of IPD_INT_SUM */
-	OCTEON_IRQ_PIP,		/* Summary of PIP_INT_REG */
-	OCTEON_IRQ_PKO,		/* Summary of PKO_REG_ERROR */
-	OCTEON_IRQ_ZIP,		/* Summary of ZIP_ERROR */
-	OCTEON_IRQ_TIM,		/* Summary of TIM_REG_ERROR */
-	OCTEON_IRQ_RAD,		/* Summary of RAD_REG_ERROR */
-	OCTEON_IRQ_KEY,		/* Summary of KEY_INT_SUM */
-	OCTEON_IRQ_DFA,		/* Summary of DFA */
-	OCTEON_IRQ_USBCTL,	/* Summary of USBN0_INT_SUM */
-	OCTEON_IRQ_SLI,		/* Summary of SLI_INT_SUM */
-	OCTEON_IRQ_DPI,		/* Summary of DPI_INT_SUM */
-	OCTEON_IRQ_AGX0,	/* Summary of GMX0*+PCS0_INT*_REG */
-	OCTEON_IRQ_AGL  = OCTEON_IRQ_AGX0 + 5,
-	OCTEON_IRQ_PTP,
-	OCTEON_IRQ_PEM0,
-	OCTEON_IRQ_PEM1,
-	OCTEON_IRQ_SRIO0,
-	OCTEON_IRQ_SRIO1,
-	OCTEON_IRQ_LMC0,
-	OCTEON_IRQ_DFM = OCTEON_IRQ_LMC0 + 4,		/* Summary of DFM */
-	OCTEON_IRQ_RST,
+#ifndef CONFIG_PCI_MSI
+	OCTEON_IRQ_LAST = 127
+#endif
 };
 
 #ifdef CONFIG_PCI_MSI
-/* 152 - 407 represent the MSI interrupts 0-255 */
-#define OCTEON_IRQ_MSI_BIT0	(OCTEON_IRQ_RST + 1)
+/* 256 - 511 represent the MSI interrupts 0-255 */
+#define OCTEON_IRQ_MSI_BIT0	(256)
 
 #define OCTEON_IRQ_MSI_LAST      (OCTEON_IRQ_MSI_BIT0 + 255)
 #define OCTEON_IRQ_LAST          (OCTEON_IRQ_MSI_LAST + 1)
-#else
-#define OCTEON_IRQ_LAST         (OCTEON_IRQ_RST + 1)
 #endif
 
 #endif

arch/mips/include/asm/mach-jz4740/jz4740_nand.h

@@ -19,6 +19,8 @@
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
 
+#define JZ_NAND_NUM_BANKS 4
+
 struct jz_nand_platform_data {
 	int			num_partitions;
 	struct mtd_partition	*partitions;
@@ -27,6 +29,8 @@ struct jz_nand_platform_data {
 
 	unsigned int busy_gpio;
 
+	unsigned char banks[JZ_NAND_NUM_BANKS];
+
 	void (*ident_callback)(struct platform_device *, struct nand_chip *,
 				struct mtd_partition **, int *num_partitions);
 };

arch/mips/include/asm/mach-loongson/loongson.h

@@ -14,6 +14,7 @@
 #include <linux/io.h>
 #include <linux/init.h>
 #include <linux/irq.h>
+#include <linux/kconfig.h>
 
 /* loongson internal northbridge initialization */
 extern void bonito_irq_init(void);
@@ -66,7 +67,7 @@ extern int mach_i8259_irq(void);
 #include <linux/interrupt.h>
 static inline void do_perfcnt_IRQ(void)
 {
-#if defined(CONFIG_OPROFILE) || defined(CONFIG_OPROFILE_MODULE)
+#if IS_ENABLED(CONFIG_OPROFILE)
 	do_IRQ(LOONGSON2_PERFCNT_IRQ);
 #endif
 }

arch/mips/include/asm/mach-loongson1/irq.h

@@ -0,0 +1,73 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * IRQ mappings for Loongson 1
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+
+#ifndef __ASM_MACH_LOONGSON1_IRQ_H
+#define __ASM_MACH_LOONGSON1_IRQ_H
+
+/*
+ * CPU core Interrupt Numbers
+ */
+#define MIPS_CPU_IRQ_BASE		0
+#define MIPS_CPU_IRQ(x)			(MIPS_CPU_IRQ_BASE + (x))
+
+#define SOFTINT0_IRQ			MIPS_CPU_IRQ(0)
+#define SOFTINT1_IRQ			MIPS_CPU_IRQ(1)
+#define INT0_IRQ			MIPS_CPU_IRQ(2)
+#define INT1_IRQ			MIPS_CPU_IRQ(3)
+#define INT2_IRQ			MIPS_CPU_IRQ(4)
+#define INT3_IRQ			MIPS_CPU_IRQ(5)
+#define INT4_IRQ			MIPS_CPU_IRQ(6)
+#define TIMER_IRQ			MIPS_CPU_IRQ(7)		/* cpu timer */
+
+#define MIPS_CPU_IRQS		(MIPS_CPU_IRQ(7) + 1 - MIPS_CPU_IRQ_BASE)
+
+/*
+ * INT0~3 Interrupt Numbers
+ */
+#define LS1X_IRQ_BASE			MIPS_CPU_IRQS
+#define LS1X_IRQ(n, x)			(LS1X_IRQ_BASE + (n << 5) + (x))
+
+#define LS1X_UART0_IRQ			LS1X_IRQ(0, 2)
+#define LS1X_UART1_IRQ			LS1X_IRQ(0, 3)
+#define LS1X_UART2_IRQ			LS1X_IRQ(0, 4)
+#define LS1X_UART3_IRQ			LS1X_IRQ(0, 5)
+#define LS1X_CAN0_IRQ			LS1X_IRQ(0, 6)
+#define LS1X_CAN1_IRQ			LS1X_IRQ(0, 7)
+#define LS1X_SPI0_IRQ			LS1X_IRQ(0, 8)
+#define LS1X_SPI1_IRQ			LS1X_IRQ(0, 9)
+#define LS1X_AC97_IRQ			LS1X_IRQ(0, 10)
+#define LS1X_DMA0_IRQ			LS1X_IRQ(0, 13)
+#define LS1X_DMA1_IRQ			LS1X_IRQ(0, 14)
+#define LS1X_DMA2_IRQ			LS1X_IRQ(0, 15)
+#define LS1X_PWM0_IRQ			LS1X_IRQ(0, 17)
+#define LS1X_PWM1_IRQ			LS1X_IRQ(0, 18)
+#define LS1X_PWM2_IRQ			LS1X_IRQ(0, 19)
+#define LS1X_PWM3_IRQ			LS1X_IRQ(0, 20)
+#define LS1X_RTC_INT0_IRQ		LS1X_IRQ(0, 21)
+#define LS1X_RTC_INT1_IRQ		LS1X_IRQ(0, 22)
+#define LS1X_RTC_INT2_IRQ		LS1X_IRQ(0, 23)
+#define LS1X_TOY_INT0_IRQ		LS1X_IRQ(0, 24)
+#define LS1X_TOY_INT1_IRQ		LS1X_IRQ(0, 25)
+#define LS1X_TOY_INT2_IRQ		LS1X_IRQ(0, 26)
+#define LS1X_RTC_TICK_IRQ		LS1X_IRQ(0, 27)
+#define LS1X_TOY_TICK_IRQ		LS1X_IRQ(0, 28)
+
+#define LS1X_EHCI_IRQ			LS1X_IRQ(1, 0)
+#define LS1X_OHCI_IRQ			LS1X_IRQ(1, 1)
+#define LS1X_GMAC0_IRQ			LS1X_IRQ(1, 2)
+#define LS1X_GMAC1_IRQ			LS1X_IRQ(1, 3)
+
+#define LS1X_IRQS		(LS1X_IRQ(4, 31) + 1 - LS1X_IRQ_BASE)
+
+#define NR_IRQS			(MIPS_CPU_IRQS + LS1X_IRQS)
+
+#endif /* __ASM_MACH_LOONGSON1_IRQ_H */

arch/mips/include/asm/mach-loongson1/loongson1.h

@@ -0,0 +1,44 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Register mappings for Loongson 1
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+
+#ifndef __ASM_MACH_LOONGSON1_LOONGSON1_H
+#define __ASM_MACH_LOONGSON1_LOONGSON1_H
+
+#define DEFAULT_MEMSIZE			256	/* If no memsize provided */
+
+/* Loongson 1 Register Bases */
+#define LS1X_INTC_BASE			0x1fd01040
+#define LS1X_EHCI_BASE			0x1fe00000
+#define LS1X_OHCI_BASE			0x1fe08000
+#define LS1X_GMAC0_BASE			0x1fe10000
+#define LS1X_GMAC1_BASE			0x1fe20000
+
+#define LS1X_UART0_BASE			0x1fe40000
+#define LS1X_UART1_BASE			0x1fe44000
+#define LS1X_UART2_BASE			0x1fe48000
+#define LS1X_UART3_BASE			0x1fe4c000
+#define LS1X_CAN0_BASE			0x1fe50000
+#define LS1X_CAN1_BASE			0x1fe54000
+#define LS1X_I2C0_BASE			0x1fe58000
+#define LS1X_I2C1_BASE			0x1fe68000
+#define LS1X_I2C2_BASE			0x1fe70000
+#define LS1X_PWM_BASE			0x1fe5c000
+#define LS1X_WDT_BASE			0x1fe5c060
+#define LS1X_RTC_BASE			0x1fe64000
+#define LS1X_AC97_BASE			0x1fe74000
+#define LS1X_NAND_BASE			0x1fe78000
+#define LS1X_CLK_BASE			0x1fe78030
+
+#include <regs-clk.h>
+#include <regs-wdt.h>
+
+#endif /* __ASM_MACH_LOONGSON1_LOONGSON1_H */

arch/mips/include/asm/mach-loongson1/platform.h

@@ -0,0 +1,23 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+
+#ifndef __ASM_MACH_LOONGSON1_PLATFORM_H
+#define __ASM_MACH_LOONGSON1_PLATFORM_H
+
+#include <linux/platform_device.h>
+
+extern struct platform_device ls1x_uart_device;
+extern struct platform_device ls1x_eth0_device;
+extern struct platform_device ls1x_ehci_device;
+extern struct platform_device ls1x_rtc_device;
+
+void ls1x_serial_setup(void);
+
+#endif /* __ASM_MACH_LOONGSON1_PLATFORM_H */

arch/mips/include/asm/mach-loongson1/prom.h

@@ -0,0 +1,24 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_MACH_LOONGSON1_PROM_H
+#define __ASM_MACH_LOONGSON1_PROM_H
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+/* environment arguments from bootloader */
+extern unsigned long memsize, highmemsize;
+
+/* loongson-specific command line, env and memory initialization */
+extern char *prom_getenv(char *name);
+extern void __init prom_init_cmdline(void);
+
+#endif /* __ASM_MACH_LOONGSON1_PROM_H */

arch/mips/include/asm/mach-loongson1/regs-clk.h

@@ -0,0 +1,33 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 Clock Register Definitions.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_MACH_LOONGSON1_REGS_CLK_H
+#define __ASM_MACH_LOONGSON1_REGS_CLK_H
+
+#define LS1X_CLK_REG(x) \
+		((void __iomem *)KSEG1ADDR(LS1X_CLK_BASE + (x)))
+
+#define LS1X_CLK_PLL_FREQ		LS1X_CLK_REG(0x0)
+#define LS1X_CLK_PLL_DIV		LS1X_CLK_REG(0x4)
+
+/* Clock PLL Divisor Register Bits */
+#define DIV_DC_EN			(0x1 << 31)
+#define DIV_DC				(0x1f << 26)
+#define DIV_CPU_EN			(0x1 << 25)
+#define DIV_CPU				(0x1f << 20)
+#define DIV_DDR_EN			(0x1 << 19)
+#define DIV_DDR				(0x1f << 14)
+
+#define DIV_DC_SHIFT			26
+#define DIV_CPU_SHIFT			20
+#define DIV_DDR_SHIFT			14
+
+#endif /* __ASM_MACH_LOONGSON1_REGS_CLK_H */

arch/mips/include/asm/mach-loongson1/regs-wdt.h

@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 watchdog register definitions.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_MACH_LOONGSON1_REGS_WDT_H
+#define __ASM_MACH_LOONGSON1_REGS_WDT_H
+
+#define LS1X_WDT_REG(x) \
+		((void __iomem *)KSEG1ADDR(LS1X_WDT_BASE + (x)))
+
+#define LS1X_WDT_EN			LS1X_WDT_REG(0x0)
+#define LS1X_WDT_SET			LS1X_WDT_REG(0x4)
+#define LS1X_WDT_TIMER			LS1X_WDT_REG(0x8)
+
+#endif /* __ASM_MACH_LOONGSON1_REGS_WDT_H */

arch/mips/include/asm/mach-loongson1/war.h

@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __ASM_MACH_LOONGSON1_WAR_H
+#define __ASM_MACH_LOONGSON1_WAR_H
+
+#define R4600_V1_INDEX_ICACHEOP_WAR	0
+#define R4600_V1_HIT_CACHEOP_WAR	0
+#define R4600_V2_HIT_CACHEOP_WAR	0
+#define R5432_CP0_INTERRUPT_WAR		0
+#define BCM1250_M3_WAR			0
+#define SIBYTE_1956_WAR			0
+#define MIPS4K_ICACHE_REFILL_WAR	0
+#define MIPS_CACHE_SYNC_WAR		0
+#define TX49XX_ICACHE_INDEX_INV_WAR	0
+#define RM9000_CDEX_SMP_WAR		0
+#define ICACHE_REFILLS_WORKAROUND_WAR	0
+#define R10000_LLSC_WAR			0
+#define MIPS34K_MISSED_ITLB_WAR		0
+
+#endif /* __ASM_MACH_LOONGSON1_WAR_H */

arch/mips/include/asm/mach-netlogic/cpu-feature-overrides.h

@@ -48,7 +48,6 @@
 #define cpu_has_userlocal	1
 #define cpu_has_mips32r2	1
 #define cpu_has_mips64r2	1
-#define cpu_has_dc_aliases	1
 #else
 #error "Unknown Netlogic CPU"
 #endif

arch/mips/include/asm/mach-tx49xx/mangle-port.h

@@ -9,7 +9,7 @@
 #define ioswabb(a, x)		(x)
 #define __mem_ioswabb(a, x)	(x)
 #if defined(CONFIG_TOSHIBA_RBTX4939) && \
-	(defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)) && \
+	IS_ENABLED(CONFIG_SMC91X) && \
 	defined(__BIG_ENDIAN)
 #define NEEDS_TXX9_IOSWABW
 extern u16 (*ioswabw)(volatile u16 *a, u16 x);

arch/mips/include/asm/mipsmtregs.h

@@ -28,6 +28,9 @@
 #define read_c0_vpeconf0()		__read_32bit_c0_register($1, 2)
 #define write_c0_vpeconf0(val)		__write_32bit_c0_register($1, 2, val)
 
+#define read_c0_vpeconf1()		__read_32bit_c0_register($1, 3)
+#define write_c0_vpeconf1(val)		__write_32bit_c0_register($1, 3, val)
+
 #define read_c0_tcstatus()		__read_32bit_c0_register($2, 1)
 #define write_c0_tcstatus(val)		__write_32bit_c0_register($2, 1, val)
 
@@ -124,6 +127,14 @@
 #define VPECONF0_XTC_SHIFT	21
 #define VPECONF0_XTC		(_ULCAST_(0xff) << VPECONF0_XTC_SHIFT)
 
+/* VPEConf1 fields (per VPE) */
+#define VPECONF1_NCP1_SHIFT	0
+#define VPECONF1_NCP1		(_ULCAST_(0xff) << VPECONF1_NCP1_SHIFT)
+#define VPECONF1_NCP2_SHIFT	10
+#define VPECONF1_NCP2		(_ULCAST_(0xff) << VPECONF1_NCP2_SHIFT)
+#define VPECONF1_NCX_SHIFT	20
+#define VPECONF1_NCX		(_ULCAST_(0xff) << VPECONF1_NCX_SHIFT)
+
 /* TCStatus fields (per TC) */
 #define TCSTATUS_TASID		(_ULCAST_(0xff))
 #define TCSTATUS_IXMT_SHIFT	10
@@ -350,6 +361,8 @@ do {									\
 #define write_vpe_c0_vpecontrol(val)	mttc0(1, 1, val)
 #define read_vpe_c0_vpeconf0()		mftc0(1, 2)
 #define write_vpe_c0_vpeconf0(val)	mttc0(1, 2, val)
+#define read_vpe_c0_vpeconf1()		mftc0(1, 3)
+#define write_vpe_c0_vpeconf1(val)	mttc0(1, 3, val)
 #define read_vpe_c0_count()		mftc0(9, 0)
 #define write_vpe_c0_count(val)		mttc0(9, 0, val)
 #define read_vpe_c0_status()		mftc0(12, 0)

arch/mips/include/asm/module.h

@@ -117,6 +117,8 @@ search_module_dbetables(unsigned long addr)
 #define MODULE_PROC_FAMILY "RM9000 "
 #elif defined CONFIG_CPU_SB1
 #define MODULE_PROC_FAMILY "SB1 "
+#elif defined CONFIG_CPU_LOONGSON1
+#define MODULE_PROC_FAMILY "LOONGSON1 "
 #elif defined CONFIG_CPU_LOONGSON2
 #define MODULE_PROC_FAMILY "LOONGSON2 "
 #elif defined CONFIG_CPU_CAVIUM_OCTEON

arch/mips/include/asm/netlogic/xlp-hal/cpucontrol.h

@@ -47,7 +47,9 @@
 #define CPU_BLOCKID_MAP		10
 
 #define LSU_DEFEATURE		0x304
-#define LSU_CERRLOG_REGID	0x09
+#define LSU_DEBUG_ADDR		0x305
+#define LSU_DEBUG_DATA0		0x306
+#define LSU_CERRLOG_REGID	0x309
 #define SCHED_DEFEATURE		0x700
 
 /* Offsets of interest from the 'MAP' Block */

arch/mips/include/asm/netlogic/xlp-hal/iomap.h

@@ -36,6 +36,9 @@
 #define __NLM_HAL_IOMAP_H__
 
 #define XLP_DEFAULT_IO_BASE             0x18000000
+#define XLP_DEFAULT_PCI_ECFG_BASE	XLP_DEFAULT_IO_BASE
+#define XLP_DEFAULT_PCI_CFG_BASE	0x1c000000
+
 #define NMI_BASE			0xbfc00000
 #define	XLP_IO_CLK			133333333
 
@@ -129,7 +132,7 @@
 #define	PCI_DEVICE_ID_NLM_PIC		0x1003
 #define	PCI_DEVICE_ID_NLM_PCIE		0x1004
 #define	PCI_DEVICE_ID_NLM_EHCI		0x1007
-#define	PCI_DEVICE_ID_NLM_ILK		0x1008
+#define	PCI_DEVICE_ID_NLM_OHCI		0x1008
 #define	PCI_DEVICE_ID_NLM_NAE		0x1009
 #define	PCI_DEVICE_ID_NLM_POE		0x100A
 #define	PCI_DEVICE_ID_NLM_FMN		0x100B

arch/mips/include/asm/netlogic/xlp-hal/pcibus.h

@@ -0,0 +1,76 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __NLM_HAL_PCIBUS_H__
+#define	__NLM_HAL_PCIBUS_H__
+
+/* PCIE Memory and IO regions */
+#define	PCIE_MEM_BASE			0xd0000000ULL
+#define	PCIE_MEM_LIMIT			0xdfffffffULL
+#define	PCIE_IO_BASE			0x14000000ULL
+#define	PCIE_IO_LIMIT			0x15ffffffULL
+
+#define	PCIE_BRIDGE_CMD			0x1
+#define	PCIE_BRIDGE_MSI_CAP		0x14
+#define	PCIE_BRIDGE_MSI_ADDRL		0x15
+#define	PCIE_BRIDGE_MSI_ADDRH		0x16
+#define	PCIE_BRIDGE_MSI_DATA		0x17
+
+/* XLP Global PCIE configuration space registers */
+#define	PCIE_BYTE_SWAP_MEM_BASE		0x247
+#define	PCIE_BYTE_SWAP_MEM_LIM		0x248
+#define	PCIE_BYTE_SWAP_IO_BASE		0x249
+#define	PCIE_BYTE_SWAP_IO_LIM		0x24A
+#define	PCIE_MSI_STATUS			0x25A
+#define	PCIE_MSI_EN			0x25B
+#define	PCIE_INT_EN0			0x261
+
+/* PCIE_MSI_EN */
+#define	PCIE_MSI_VECTOR_INT_EN		0xFFFFFFFF
+
+/* PCIE_INT_EN0 */
+#define	PCIE_MSI_INT_EN			(1 << 9)
+
+#ifndef __ASSEMBLY__
+
+#define	nlm_read_pcie_reg(b, r)		nlm_read_reg(b, r)
+#define	nlm_write_pcie_reg(b, r, v)	nlm_write_reg(b, r, v)
+#define	nlm_get_pcie_base(node, inst)	\
+			nlm_pcicfg_base(XLP_IO_PCIE_OFFSET(node, inst))
+#define	nlm_get_pcie_regbase(node, inst)	\
+			(nlm_get_pcie_base(node, inst) + XLP_IO_PCI_HDRSZ)
+
+int xlp_pcie_link_irt(int link);
+#endif
+#endif /* __NLM_HAL_PCIBUS_H__ */

arch/mips/include/asm/netlogic/xlp-hal/pic.h

@@ -201,7 +201,11 @@
 #define PIC_NUM_USB_IRTS		6
 #define PIC_IRT_USB_0_INDEX		115
 #define PIC_IRT_EHCI_0_INDEX		115
+#define PIC_IRT_OHCI_0_INDEX		116
+#define PIC_IRT_OHCI_1_INDEX		117
 #define PIC_IRT_EHCI_1_INDEX		118
+#define PIC_IRT_OHCI_2_INDEX		119
+#define PIC_IRT_OHCI_3_INDEX		120
 #define PIC_IRT_USB_INDEX(num)		((num) + PIC_IRT_USB_0_INDEX)
 /* 115 to 120 */
 #define PIC_IRT_GDX_INDEX		121

arch/mips/include/asm/netlogic/xlp-hal/usb.h

@@ -0,0 +1,64 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __NLM_HAL_USB_H__
+#define __NLM_HAL_USB_H__
+
+#define USB_CTL_0			0x01
+#define USB_PHY_0			0x0A
+#define USB_PHY_RESET			0x01
+#define USB_PHY_PORT_RESET_0		0x10
+#define USB_PHY_PORT_RESET_1		0x20
+#define USB_CONTROLLER_RESET		0x01
+#define USB_INT_STATUS			0x0E
+#define USB_INT_EN			0x0F
+#define USB_PHY_INTERRUPT_EN		0x01
+#define USB_OHCI_INTERRUPT_EN		0x02
+#define USB_OHCI_INTERRUPT1_EN		0x04
+#define USB_OHCI_INTERRUPT2_EN		0x08
+#define USB_CTRL_INTERRUPT_EN		0x10
+
+#ifndef __ASSEMBLY__
+
+#define nlm_read_usb_reg(b, r)			nlm_read_reg(b, r)
+#define nlm_write_usb_reg(b, r, v)		nlm_write_reg(b, r, v)
+#define nlm_get_usb_pcibase(node, inst)		\
+	nlm_pcicfg_base(XLP_IO_USB_OFFSET(node, inst))
+#define nlm_get_usb_hcd_base(node, inst)	\
+	nlm_xkphys_map_pcibar0(nlm_get_usb_pcibase(node, inst))
+#define nlm_get_usb_regbase(node, inst)		\
+	(nlm_get_usb_pcibase(node, inst) + XLP_IO_PCI_HDRSZ)
+
+#endif
+#endif /* __NLM_HAL_USB_H__ */

arch/mips/include/asm/netlogic/xlp-hal/xlp.h

@@ -35,8 +35,21 @@
 #ifndef _NLM_HAL_XLP_H
 #define _NLM_HAL_XLP_H
 
-#define PIC_UART_0_IRQ           17
-#define PIC_UART_1_IRQ           18
+#define PIC_UART_0_IRQ			17
+#define PIC_UART_1_IRQ			18
+#define PIC_PCIE_LINK_0_IRQ		19
+#define PIC_PCIE_LINK_1_IRQ		20
+#define PIC_PCIE_LINK_2_IRQ		21
+#define PIC_PCIE_LINK_3_IRQ		22
+#define PIC_EHCI_0_IRQ			23
+#define PIC_EHCI_1_IRQ			24
+#define PIC_OHCI_0_IRQ			25
+#define PIC_OHCI_1_IRQ			26
+#define PIC_OHCI_2_IRQ			27
+#define PIC_OHCI_3_IRQ			28
+#define PIC_MMC_IRQ			29
+#define PIC_I2C_0_IRQ			30
+#define PIC_I2C_1_IRQ			31
 
 #ifndef __ASSEMBLY__
 

arch/mips/include/asm/netlogic/xlr/bridge.h

@@ -0,0 +1,104 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _ASM_NLM_BRIDGE_H_
+#define _ASM_NLM_BRIDGE_H_
+
+#define BRIDGE_DRAM_0_BAR		0
+#define BRIDGE_DRAM_1_BAR		1
+#define BRIDGE_DRAM_2_BAR		2
+#define BRIDGE_DRAM_3_BAR		3
+#define BRIDGE_DRAM_4_BAR		4
+#define BRIDGE_DRAM_5_BAR		5
+#define BRIDGE_DRAM_6_BAR		6
+#define BRIDGE_DRAM_7_BAR		7
+#define BRIDGE_DRAM_CHN_0_MTR_0_BAR	8
+#define BRIDGE_DRAM_CHN_0_MTR_1_BAR	9
+#define BRIDGE_DRAM_CHN_0_MTR_2_BAR	10
+#define BRIDGE_DRAM_CHN_0_MTR_3_BAR	11
+#define BRIDGE_DRAM_CHN_0_MTR_4_BAR	12
+#define BRIDGE_DRAM_CHN_0_MTR_5_BAR	13
+#define BRIDGE_DRAM_CHN_0_MTR_6_BAR	14
+#define BRIDGE_DRAM_CHN_0_MTR_7_BAR	15
+#define BRIDGE_DRAM_CHN_1_MTR_0_BAR	16
+#define BRIDGE_DRAM_CHN_1_MTR_1_BAR	17
+#define BRIDGE_DRAM_CHN_1_MTR_2_BAR	18
+#define BRIDGE_DRAM_CHN_1_MTR_3_BAR	19
+#define BRIDGE_DRAM_CHN_1_MTR_4_BAR	20
+#define BRIDGE_DRAM_CHN_1_MTR_5_BAR	21
+#define BRIDGE_DRAM_CHN_1_MTR_6_BAR	22
+#define BRIDGE_DRAM_CHN_1_MTR_7_BAR	23
+#define BRIDGE_CFG_BAR			24
+#define BRIDGE_PHNX_IO_BAR		25
+#define BRIDGE_FLASH_BAR		26
+#define BRIDGE_SRAM_BAR			27
+#define BRIDGE_HTMEM_BAR		28
+#define BRIDGE_HTINT_BAR		29
+#define BRIDGE_HTPIC_BAR		30
+#define BRIDGE_HTSM_BAR			31
+#define BRIDGE_HTIO_BAR			32
+#define BRIDGE_HTCFG_BAR		33
+#define BRIDGE_PCIXCFG_BAR		34
+#define BRIDGE_PCIXMEM_BAR		35
+#define BRIDGE_PCIXIO_BAR		36
+#define BRIDGE_DEVICE_MASK		37
+#define BRIDGE_AERR_INTR_LOG1		38
+#define BRIDGE_AERR_INTR_LOG2		39
+#define BRIDGE_AERR_INTR_LOG3		40
+#define BRIDGE_AERR_DEV_STAT		41
+#define BRIDGE_AERR1_LOG1		42
+#define BRIDGE_AERR1_LOG2		43
+#define BRIDGE_AERR1_LOG3		44
+#define BRIDGE_AERR1_DEV_STAT		45
+#define BRIDGE_AERR_INTR_EN		46
+#define BRIDGE_AERR_UPG			47
+#define BRIDGE_AERR_CLEAR		48
+#define BRIDGE_AERR1_CLEAR		49
+#define BRIDGE_SBE_COUNTS		50
+#define BRIDGE_DBE_COUNTS		51
+#define BRIDGE_BITERR_INT_EN		52
+
+#define BRIDGE_SYS2IO_CREDITS		53
+#define BRIDGE_EVNT_CNT_CTRL1		54
+#define BRIDGE_EVNT_COUNTER1		55
+#define BRIDGE_EVNT_CNT_CTRL2		56
+#define BRIDGE_EVNT_COUNTER2		57
+#define BRIDGE_RESERVED1		58
+
+#define BRIDGE_DEFEATURE		59
+#define BRIDGE_SCRATCH0			60
+#define BRIDGE_SCRATCH1			61
+#define BRIDGE_SCRATCH2			62
+#define BRIDGE_SCRATCH3			63
+
+#endif

arch/mips/include/asm/netlogic/xlr/flash.h

@@ -0,0 +1,55 @@
+/*
+ * Copyright (c) 2003-2012 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _ASM_NLM_FLASH_H_
+#define _ASM_NLM_FLASH_H_
+
+#define FLASH_CSBASE_ADDR(cs)		(cs)
+#define FLASH_CSADDR_MASK(cs)		(0x10 + (cs))
+#define FLASH_CSDEV_PARM(cs)		(0x20 + (cs))
+#define FLASH_CSTIME_PARMA(cs)		(0x30 + (cs))
+#define FLASH_CSTIME_PARMB(cs)		(0x40 + (cs))
+
+#define FLASH_INT_MASK			0x50
+#define FLASH_INT_STATUS		0x60
+#define FLASH_ERROR_STATUS		0x70
+#define FLASH_ERROR_ADDR		0x80
+
+#define FLASH_NAND_CLE(cs)		(0x90 + (cs))
+#define FLASH_NAND_ALE(cs)		(0xa0 + (cs))
+
+#define FLASH_NAND_CSDEV_PARAM		0x000041e6
+#define FLASH_NAND_CSTIME_PARAMA	0x4f400e22
+#define FLASH_NAND_CSTIME_PARAMB	0x000083cf
+
+#endif

arch/mips/include/asm/netlogic/xlr/gpio.h

@@ -35,39 +35,40 @@
 #ifndef _ASM_NLM_GPIO_H
 #define _ASM_NLM_GPIO_H
 
-#define NETLOGIC_GPIO_INT_EN_REG		0
-#define NETLOGIC_GPIO_INPUT_INVERSION_REG	1
-#define NETLOGIC_GPIO_IO_DIR_REG		2
-#define NETLOGIC_GPIO_IO_DATA_WR_REG		3
-#define NETLOGIC_GPIO_IO_DATA_RD_REG		4
+#define GPIO_INT_EN_REG			0
+#define GPIO_INPUT_INVERSION_REG	1
+#define GPIO_IO_DIR_REG			2
+#define GPIO_IO_DATA_WR_REG		3
+#define GPIO_IO_DATA_RD_REG		4
 
-#define NETLOGIC_GPIO_SWRESET_REG		8
-#define NETLOGIC_GPIO_DRAM1_CNTRL_REG		9
-#define NETLOGIC_GPIO_DRAM1_RATIO_REG		10
-#define NETLOGIC_GPIO_DRAM1_RESET_REG		11
-#define NETLOGIC_GPIO_DRAM1_STATUS_REG		12
-#define NETLOGIC_GPIO_DRAM2_CNTRL_REG		13
-#define NETLOGIC_GPIO_DRAM2_RATIO_REG		14
-#define NETLOGIC_GPIO_DRAM2_RESET_REG		15
-#define NETLOGIC_GPIO_DRAM2_STATUS_REG		16
+#define GPIO_SWRESET_REG		8
+#define GPIO_DRAM1_CNTRL_REG		9
+#define GPIO_DRAM1_RATIO_REG		10
+#define GPIO_DRAM1_RESET_REG		11
+#define GPIO_DRAM1_STATUS_REG		12
+#define GPIO_DRAM2_CNTRL_REG		13
+#define GPIO_DRAM2_RATIO_REG		14
+#define GPIO_DRAM2_RESET_REG		15
+#define GPIO_DRAM2_STATUS_REG		16
 
-#define NETLOGIC_GPIO_PWRON_RESET_CFG_REG	21
-#define NETLOGIC_GPIO_BIST_ALL_GO_STATUS_REG	24
-#define NETLOGIC_GPIO_BIST_CPU_GO_STATUS_REG	25
-#define NETLOGIC_GPIO_BIST_DEV_GO_STATUS_REG	26
+#define GPIO_PWRON_RESET_CFG_REG	21
+#define GPIO_BIST_ALL_GO_STATUS_REG	24
+#define GPIO_BIST_CPU_GO_STATUS_REG	25
+#define GPIO_BIST_DEV_GO_STATUS_REG	26
 
-#define NETLOGIC_GPIO_FUSE_BANK_REG		35
-#define NETLOGIC_GPIO_CPU_RESET_REG		40
-#define NETLOGIC_GPIO_RNG_REG			43
+#define GPIO_FUSE_BANK_REG		35
+#define GPIO_CPU_RESET_REG		40
+#define GPIO_RNG_REG			43
 
-#define NETLOGIC_PWRON_RESET_PCMCIA_BOOT	17
-#define NETLOGIC_GPIO_LED_BITMAP	0x1700000
-#define NETLOGIC_GPIO_LED_0_SHIFT		20
-#define NETLOGIC_GPIO_LED_1_SHIFT		24
+#define PWRON_RESET_PCMCIA_BOOT		17
 
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_RESET	0x01
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_HARD_RESET 0x02
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_SOFT_RESET 0x03
-#define NETLOGIC_GPIO_LED_OUTPUT_CODE_MAIN	0x04
+#define GPIO_LED_BITMAP			0x1700000
+#define GPIO_LED_0_SHIFT		20
+#define GPIO_LED_1_SHIFT		24
+
+#define GPIO_LED_OUTPUT_CODE_RESET	0x01
+#define GPIO_LED_OUTPUT_CODE_HARD_RESET 0x02
+#define GPIO_LED_OUTPUT_CODE_SOFT_RESET 0x03
+#define GPIO_LED_OUTPUT_CODE_MAIN	0x04
 
 #endif

arch/mips/include/asm/octeon/cvmx-helper-fpa.h

@@ -1,64 +0,0 @@
-/***********************license start***************
- * Author: Cavium Networks
- *
- * Contact: support@caviumnetworks.com
- * This file is part of the OCTEON SDK
- *
- * Copyright (c) 2003-2008 Cavium Networks
- *
- * This file is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License, Version 2, as
- * published by the Free Software Foundation.
- *
- * This file is distributed in the hope that it will be useful, but
- * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
- * NONINFRINGEMENT.  See the GNU General Public License for more
- * details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this file; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- * or visit http://www.gnu.org/licenses/.
- *
- * This file may also be available under a different license from Cavium.
- * Contact Cavium Networks for more information
- ***********************license end**************************************/
-
-/**
- * @file
- *
- * Helper functions for FPA setup.
- *
- */
-#ifndef __CVMX_HELPER_H_FPA__
-#define __CVMX_HELPER_H_FPA__
-
-/**
- * Allocate memory and initialize the FPA pools using memory
- * from cvmx-bootmem. Sizes of each element in the pools is
- * controlled by the cvmx-config.h header file. Specifying
- * zero for any parameter will cause that FPA pool to not be
- * setup. This is useful if you aren't using some of the
- * hardware and want to save memory.
- *
- * @packet_buffers:
- *               Number of packet buffers to allocate
- * @work_queue_entries:
- *               Number of work queue entries
- * @pko_buffers:
- *               PKO Command buffers. You should at minimum have two per
- *               each PKO queue.
- * @tim_buffers:
- *               TIM ring buffer command queues. At least two per timer bucket
- *               is recommened.
- * @dfa_buffers:
- *               DFA command buffer. A relatively small (32 for example)
- *               number should work.
- * Returns Zero on success, non-zero if out of memory
- */
-extern int cvmx_helper_initialize_fpa(int packet_buffers,
-				      int work_queue_entries, int pko_buffers,
-				      int tim_buffers, int dfa_buffers);
-
-#endif /* __CVMX_HELPER_H__ */

arch/mips/include/asm/octeon/cvmx-helper.h

@@ -61,8 +61,6 @@ typedef union {
 	} s;
 } cvmx_helper_link_info_t;
 
-#include "cvmx-helper-fpa.h"
-
 #include <asm/octeon/cvmx-helper-errata.h>
 #include "cvmx-helper-loop.h"
 #include "cvmx-helper-npi.h"

arch/mips/include/asm/octeon/octeon.h

@@ -215,11 +215,6 @@ struct octeon_cf_data {
 	int		dma_engine;	/* -1 for no DMA */
 };
 
-struct octeon_i2c_data {
-	unsigned int	sys_freq;
-	unsigned int	i2c_freq;
-};
-
 extern void octeon_write_lcd(const char *s);
 extern void octeon_check_cpu_bist(void);
 extern int octeon_get_boot_debug_flag(void);

arch/mips/include/asm/prom.h

@@ -20,9 +20,6 @@
 extern int early_init_dt_scan_memory_arch(unsigned long node,
 	const char *uname, int depth, void *data);
 
-extern int reserve_mem_mach(unsigned long addr, unsigned long size);
-extern void free_mem_mach(unsigned long addr, unsigned long size);
-
 extern void device_tree_init(void);
 
 static inline unsigned long pci_address_to_pio(phys_addr_t address)

arch/mips/include/asm/smtc.h

@@ -33,6 +33,12 @@ typedef long asiduse;
 #endif
 #endif
 
+/*
+ * VPE Management information
+ */
+
+#define MAX_SMTC_VPES	MAX_SMTC_TLBS	/* FIXME: May not always be true. */
+
 extern asiduse smtc_live_asid[MAX_SMTC_TLBS][MAX_SMTC_ASIDS];
 
 struct mm_struct;

arch/mips/include/asm/uaccess.h

@@ -687,7 +687,7 @@ extern size_t __copy_user(void *__to, const void *__from, size_t __n);
 	__MODULE_JAL(__copy_user)					\
 	: "+r" (__cu_to_r), "+r" (__cu_from_r), "+r" (__cu_len_r)	\
 	:								\
-	: "$8", "$9", "$10", "$11", "$12", "$15", "$24", "$31",		\
+	: "$8", "$9", "$10", "$11", "$12", "$14", "$15", "$24", "$31",	\
 	  DADDI_SCRATCH, "memory");					\
 	__cu_len_r;							\
 })
@@ -797,7 +797,7 @@ extern size_t __copy_user_inatomic(void *__to, const void *__from, size_t __n);
 	".set\treorder"							\
 	: "+r" (__cu_to_r), "+r" (__cu_from_r), "+r" (__cu_len_r)	\
 	:								\
-	: "$8", "$9", "$10", "$11", "$12", "$15", "$24", "$31",		\
+	: "$8", "$9", "$10", "$11", "$12", "$14", "$15", "$24", "$31",	\
 	  DADDI_SCRATCH, "memory");					\
 	__cu_len_r;							\
 })
@@ -820,7 +820,7 @@ extern size_t __copy_user_inatomic(void *__to, const void *__from, size_t __n);
 	".set\treorder"							\
 	: "+r" (__cu_to_r), "+r" (__cu_from_r), "+r" (__cu_len_r)	\
 	:								\
-	: "$8", "$9", "$10", "$11", "$12", "$15", "$24", "$31",		\
+	: "$8", "$9", "$10", "$11", "$12", "$14", "$15", "$24", "$31",	\
 	  DADDI_SCRATCH, "memory");					\
 	__cu_len_r;							\
 })

arch/mips/include/asm/uasm.h

@@ -6,6 +6,7 @@
  * Copyright (C) 2004, 2005, 2006, 2008  Thiemo Seufer
  * Copyright (C) 2005  Maciej W. Rozycki
  * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2012  MIPS Technologies, Inc.
  */
 
 #include <linux/types.h>
@@ -62,8 +63,10 @@ void __uasminit uasm_i##op(u32 **buf, unsigned int a, signed int b)
 
 Ip_u2u1s3(_addiu);
 Ip_u3u1u2(_addu);
-Ip_u2u1u3(_andi);
 Ip_u3u1u2(_and);
+Ip_u2u1u3(_andi);
+Ip_u1u2s3(_bbit0);
+Ip_u1u2s3(_bbit1);
 Ip_u1u2s3(_beq);
 Ip_u1u2s3(_beql);
 Ip_u1s2(_bgez);
@@ -72,55 +75,54 @@ Ip_u1s2(_bltz);
 Ip_u1s2(_bltzl);
 Ip_u1u2s3(_bne);
 Ip_u2s3u1(_cache);
-Ip_u1u2u3(_dmfc0);
-Ip_u1u2u3(_dmtc0);
 Ip_u2u1s3(_daddiu);
 Ip_u3u1u2(_daddu);
+Ip_u2u1msbu3(_dins);
+Ip_u2u1msbu3(_dinsm);
+Ip_u1u2u3(_dmfc0);
+Ip_u1u2u3(_dmtc0);
+Ip_u2u1u3(_drotr);
+Ip_u2u1u3(_drotr32);
 Ip_u2u1u3(_dsll);
 Ip_u2u1u3(_dsll32);
 Ip_u2u1u3(_dsra);
 Ip_u2u1u3(_dsrl);
 Ip_u2u1u3(_dsrl32);
-Ip_u2u1u3(_drotr);
-Ip_u2u1u3(_drotr32);
 Ip_u3u1u2(_dsubu);
 Ip_0(_eret);
 Ip_u1(_j);
 Ip_u1(_jal);
 Ip_u1(_jr);
 Ip_u2s3u1(_ld);
+Ip_u3u1u2(_ldx);
 Ip_u2s3u1(_ll);
 Ip_u2s3u1(_lld);
 Ip_u1s2(_lui);
 Ip_u2s3u1(_lw);
+Ip_u3u1u2(_lwx);
 Ip_u1u2u3(_mfc0);
 Ip_u1u2u3(_mtc0);
-Ip_u2u1u3(_ori);
 Ip_u3u1u2(_or);
+Ip_u2u1u3(_ori);
 Ip_u2s3u1(_pref);
 Ip_0(_rfe);
+Ip_u2u1u3(_rotr);
 Ip_u2s3u1(_sc);
 Ip_u2s3u1(_scd);
 Ip_u2s3u1(_sd);
 Ip_u2u1u3(_sll);
 Ip_u2u1u3(_sra);
 Ip_u2u1u3(_srl);
-Ip_u2u1u3(_rotr);
 Ip_u3u1u2(_subu);
 Ip_u2s3u1(_sw);
+Ip_u1(_syscall);
 Ip_0(_tlbp);
 Ip_0(_tlbr);
 Ip_0(_tlbwi);
 Ip_0(_tlbwr);
 Ip_u3u1u2(_xor);
 Ip_u2u1u3(_xori);
-Ip_u2u1msbu3(_dins);
-Ip_u2u1msbu3(_dinsm);
-Ip_u1(_syscall);
-Ip_u1u2s3(_bbit0);
-Ip_u1u2s3(_bbit1);
-Ip_u3u1u2(_lwx);
-Ip_u3u1u2(_ldx);
+
 
 /* Handle labels. */
 struct uasm_label {
@@ -145,37 +147,37 @@ static inline void __uasminit uasm_l##lb(struct uasm_label **lab, u32 *addr) \
 
 /* convenience macros for instructions */
 #ifdef CONFIG_64BIT
+# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_daddiu(buf, rs, rt, val)
+# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_daddu(buf, rs, rt, rd)
+# define UASM_i_LL(buf, rs, rt, off) uasm_i_lld(buf, rs, rt, off)
 # define UASM_i_LW(buf, rs, rt, off) uasm_i_ld(buf, rs, rt, off)
-# define UASM_i_SW(buf, rs, rt, off) uasm_i_sd(buf, rs, rt, off)
+# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_ldx(buf, rs, rt, rd)
+# define UASM_i_MFC0(buf, rt, rd...) uasm_i_dmfc0(buf, rt, rd)
+# define UASM_i_MTC0(buf, rt, rd...) uasm_i_dmtc0(buf, rt, rd)
+# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_drotr(buf, rs, rt, sh)
+# define UASM_i_SC(buf, rs, rt, off) uasm_i_scd(buf, rs, rt, off)
 # define UASM_i_SLL(buf, rs, rt, sh) uasm_i_dsll(buf, rs, rt, sh)
 # define UASM_i_SRA(buf, rs, rt, sh) uasm_i_dsra(buf, rs, rt, sh)
 # define UASM_i_SRL(buf, rs, rt, sh) uasm_i_dsrl(buf, rs, rt, sh)
 # define UASM_i_SRL_SAFE(buf, rs, rt, sh) uasm_i_dsrl_safe(buf, rs, rt, sh)
-# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_drotr(buf, rs, rt, sh)
-# define UASM_i_MFC0(buf, rt, rd...) uasm_i_dmfc0(buf, rt, rd)
-# define UASM_i_MTC0(buf, rt, rd...) uasm_i_dmtc0(buf, rt, rd)
-# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_daddiu(buf, rs, rt, val)
-# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_daddu(buf, rs, rt, rd)
 # define UASM_i_SUBU(buf, rs, rt, rd) uasm_i_dsubu(buf, rs, rt, rd)
-# define UASM_i_LL(buf, rs, rt, off) uasm_i_lld(buf, rs, rt, off)
-# define UASM_i_SC(buf, rs, rt, off) uasm_i_scd(buf, rs, rt, off)
-# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_ldx(buf, rs, rt, rd)
+# define UASM_i_SW(buf, rs, rt, off) uasm_i_sd(buf, rs, rt, off)
 #else
+# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_addiu(buf, rs, rt, val)
+# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_addu(buf, rs, rt, rd)
+# define UASM_i_LL(buf, rs, rt, off) uasm_i_ll(buf, rs, rt, off)
 # define UASM_i_LW(buf, rs, rt, off) uasm_i_lw(buf, rs, rt, off)
-# define UASM_i_SW(buf, rs, rt, off) uasm_i_sw(buf, rs, rt, off)
+# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_lwx(buf, rs, rt, rd)
+# define UASM_i_MFC0(buf, rt, rd...) uasm_i_mfc0(buf, rt, rd)
+# define UASM_i_MTC0(buf, rt, rd...) uasm_i_mtc0(buf, rt, rd)
+# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_rotr(buf, rs, rt, sh)
+# define UASM_i_SC(buf, rs, rt, off) uasm_i_sc(buf, rs, rt, off)
 # define UASM_i_SLL(buf, rs, rt, sh) uasm_i_sll(buf, rs, rt, sh)
 # define UASM_i_SRA(buf, rs, rt, sh) uasm_i_sra(buf, rs, rt, sh)
 # define UASM_i_SRL(buf, rs, rt, sh) uasm_i_srl(buf, rs, rt, sh)
 # define UASM_i_SRL_SAFE(buf, rs, rt, sh) uasm_i_srl(buf, rs, rt, sh)
-# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_rotr(buf, rs, rt, sh)
-# define UASM_i_MFC0(buf, rt, rd...) uasm_i_mfc0(buf, rt, rd)
-# define UASM_i_MTC0(buf, rt, rd...) uasm_i_mtc0(buf, rt, rd)
-# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_addiu(buf, rs, rt, val)
-# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_addu(buf, rs, rt, rd)
 # define UASM_i_SUBU(buf, rs, rt, rd) uasm_i_subu(buf, rs, rt, rd)
-# define UASM_i_LL(buf, rs, rt, off) uasm_i_ll(buf, rs, rt, off)
-# define UASM_i_SC(buf, rs, rt, off) uasm_i_sc(buf, rs, rt, off)
-# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_lwx(buf, rs, rt, rd)
+# define UASM_i_SW(buf, rs, rt, off) uasm_i_sw(buf, rs, rt, off)
 #endif
 
 #define uasm_i_b(buf, off) uasm_i_beq(buf, 0, 0, off)
@@ -183,19 +185,10 @@ static inline void __uasminit uasm_l##lb(struct uasm_label **lab, u32 *addr) \
 #define uasm_i_beqzl(buf, rs, off) uasm_i_beql(buf, rs, 0, off)
 #define uasm_i_bnez(buf, rs, off) uasm_i_bne(buf, rs, 0, off)
 #define uasm_i_bnezl(buf, rs, off) uasm_i_bnel(buf, rs, 0, off)
+#define uasm_i_ehb(buf) uasm_i_sll(buf, 0, 0, 3)
 #define uasm_i_move(buf, a, b) UASM_i_ADDU(buf, a, 0, b)
 #define uasm_i_nop(buf) uasm_i_sll(buf, 0, 0, 0)
 #define uasm_i_ssnop(buf) uasm_i_sll(buf, 0, 0, 1)
-#define uasm_i_ehb(buf) uasm_i_sll(buf, 0, 0, 3)
-
-static inline void uasm_i_dsrl_safe(u32 **p, unsigned int a1,
-				    unsigned int a2, unsigned int a3)
-{
-	if (a3 < 32)
-		uasm_i_dsrl(p, a1, a2, a3);
-	else
-		uasm_i_dsrl32(p, a1, a2, a3 - 32);
-}
 
 static inline void uasm_i_drotr_safe(u32 **p, unsigned int a1,
 				     unsigned int a2, unsigned int a3)
@@ -215,6 +208,15 @@ static inline void uasm_i_dsll_safe(u32 **p, unsigned int a1,
 		uasm_i_dsll32(p, a1, a2, a3 - 32);
 }
 
+static inline void uasm_i_dsrl_safe(u32 **p, unsigned int a1,
+				    unsigned int a2, unsigned int a3)
+{
+	if (a3 < 32)
+		uasm_i_dsrl(p, a1, a2, a3);
+	else
+		uasm_i_dsrl32(p, a1, a2, a3 - 32);
+}
+
 /* Handle relocations. */
 struct uasm_reloc {
 	u32 *addr;
@@ -234,16 +236,16 @@ void uasm_copy_handler(struct uasm_reloc *rel, struct uasm_label *lab,
 int uasm_insn_has_bdelay(struct uasm_reloc *rel, u32 *addr);
 
 /* Convenience functions for labeled branches. */
-void uasm_il_bltz(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
 void uasm_il_b(u32 **p, struct uasm_reloc **r, int lid);
+void uasm_il_bbit0(u32 **p, struct uasm_reloc **r, unsigned int reg,
+		   unsigned int bit, int lid);
+void uasm_il_bbit1(u32 **p, struct uasm_reloc **r, unsigned int reg,
+		   unsigned int bit, int lid);
 void uasm_il_beqz(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
 void uasm_il_beqzl(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bgezl(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bgez(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bltz(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
 void uasm_il_bne(u32 **p, struct uasm_reloc **r, unsigned int reg1,
 		 unsigned int reg2, int lid);
 void uasm_il_bnez(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
-void uasm_il_bgezl(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
-void uasm_il_bgez(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
-void uasm_il_bbit0(u32 **p, struct uasm_reloc **r, unsigned int reg,
-		   unsigned int bit, int lid);
-void uasm_il_bbit1(u32 **p, struct uasm_reloc **r, unsigned int reg,
-		   unsigned int bit, int lid);

arch/mips/jz4740/board-qi_lb60.c

@@ -140,6 +140,7 @@ static void qi_lb60_nand_ident(struct platform_device *pdev,
 static struct jz_nand_platform_data qi_lb60_nand_pdata = {
 	.ident_callback = qi_lb60_nand_ident,
 	.busy_gpio = 94,
+	.banks = { 1 },
 };
 
 /* Keyboard*/

arch/mips/jz4740/platform.c

@@ -157,11 +157,29 @@ static struct resource jz4740_nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	{
-		.name	= "bank",
+		.name	= "bank1",
 		.start	= 0x18000000,
 		.end	= 0x180C0000 - 1,
 		.flags = IORESOURCE_MEM,
 	},
+	{
+		.name	= "bank2",
+		.start	= 0x14000000,
+		.end	= 0x140C0000 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.name	= "bank3",
+		.start	= 0x0C000000,
+		.end	= 0x0C0C0000 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.name	= "bank4",
+		.start	= 0x08000000,
+		.end	= 0x080C0000 - 1,
+		.flags = IORESOURCE_MEM,
+	},
 };
 
 struct platform_device jz4740_nand_device = {

arch/mips/jz4740/reset.c

@@ -21,6 +21,9 @@
 #include <asm/mach-jz4740/base.h>
 #include <asm/mach-jz4740/timer.h>
 
+#include "reset.h"
+#include "clock.h"
+
 static void jz4740_halt(void)
 {
 	while (1) {
@@ -53,21 +56,57 @@ static void jz4740_restart(char *command)
 	jz4740_halt();
 }
 
-#define JZ_REG_RTC_CTRL		0x00
-#define JZ_REG_RTC_HIBERNATE	0x20
+#define JZ_REG_RTC_CTRL			0x00
+#define JZ_REG_RTC_HIBERNATE		0x20
+#define JZ_REG_RTC_WAKEUP_FILTER	0x24
+#define JZ_REG_RTC_RESET_COUNTER	0x28
 
-#define JZ_RTC_CTRL_WRDY	BIT(7)
+#define JZ_RTC_CTRL_WRDY		BIT(7)
+#define JZ_RTC_WAKEUP_FILTER_MASK	0x0000FFE0
+#define JZ_RTC_RESET_COUNTER_MASK	0x00000FE0
 
-static void jz4740_power_off(void)
+static inline void jz4740_rtc_wait_ready(void __iomem *rtc_base)
 {
-	void __iomem *rtc_base = ioremap(JZ4740_RTC_BASE_ADDR, 0x24);
 	uint32_t ctrl;
 
 	do {
 		ctrl = readl(rtc_base + JZ_REG_RTC_CTRL);
 	} while (!(ctrl & JZ_RTC_CTRL_WRDY));
+}
 
+static void jz4740_power_off(void)
+{
+	void __iomem *rtc_base = ioremap(JZ4740_RTC_BASE_ADDR, 0x38);
+	unsigned long wakeup_filter_ticks;
+	unsigned long reset_counter_ticks;
+
+	/*
+	 * Set minimum wakeup pin assertion time: 100 ms.
+	 * Range is 0 to 2 sec if RTC is clocked at 32 kHz.
+	 */
+	wakeup_filter_ticks = (100 * jz4740_clock_bdata.rtc_rate) / 1000;
+	if (wakeup_filter_ticks < JZ_RTC_WAKEUP_FILTER_MASK)
+		wakeup_filter_ticks &= JZ_RTC_WAKEUP_FILTER_MASK;
+	else
+		wakeup_filter_ticks = JZ_RTC_WAKEUP_FILTER_MASK;
+	jz4740_rtc_wait_ready(rtc_base);
+	writel(wakeup_filter_ticks, rtc_base + JZ_REG_RTC_WAKEUP_FILTER);
+
+	/*
+	 * Set reset pin low-level assertion time after wakeup: 60 ms.
+	 * Range is 0 to 125 ms if RTC is clocked at 32 kHz.
+	 */
+	reset_counter_ticks = (60 * jz4740_clock_bdata.rtc_rate) / 1000;
+	if (reset_counter_ticks < JZ_RTC_RESET_COUNTER_MASK)
+		reset_counter_ticks &= JZ_RTC_RESET_COUNTER_MASK;
+	else
+		reset_counter_ticks = JZ_RTC_RESET_COUNTER_MASK;
+	jz4740_rtc_wait_ready(rtc_base);
+	writel(reset_counter_ticks, rtc_base + JZ_REG_RTC_RESET_COUNTER);
+
+	jz4740_rtc_wait_ready(rtc_base);
 	writel(1, rtc_base + JZ_REG_RTC_HIBERNATE);
+
 	jz4740_halt();
 }
 

arch/mips/kernel/cpu-probe.c

@@ -190,6 +190,7 @@ void __init check_wait(void)
 	case CPU_CAVIUM_OCTEON_PLUS:
 	case CPU_CAVIUM_OCTEON2:
 	case CPU_JZRISC:
+	case CPU_LOONGSON1:
 	case CPU_XLR:
 	case CPU_XLP:
 		cpu_wait = r4k_wait;
@@ -330,6 +331,154 @@ static inline void cpu_probe_vmbits(struct cpuinfo_mips *c)
 #endif
 }
 
+static char unknown_isa[] __cpuinitdata = KERN_ERR \
+	"Unsupported ISA type, c0.config0: %d.";
+
+static inline unsigned int decode_config0(struct cpuinfo_mips *c)
+{
+	unsigned int config0;
+	int isa;
+
+	config0 = read_c0_config();
+
+	if (((config0 & MIPS_CONF_MT) >> 7) == 1)
+		c->options |= MIPS_CPU_TLB;
+	isa = (config0 & MIPS_CONF_AT) >> 13;
+	switch (isa) {
+	case 0:
+		switch ((config0 & MIPS_CONF_AR) >> 10) {
+		case 0:
+			c->isa_level = MIPS_CPU_ISA_M32R1;
+			break;
+		case 1:
+			c->isa_level = MIPS_CPU_ISA_M32R2;
+			break;
+		default:
+			goto unknown;
+		}
+		break;
+	case 2:
+		switch ((config0 & MIPS_CONF_AR) >> 10) {
+		case 0:
+			c->isa_level = MIPS_CPU_ISA_M64R1;
+			break;
+		case 1:
+			c->isa_level = MIPS_CPU_ISA_M64R2;
+			break;
+		default:
+			goto unknown;
+		}
+		break;
+	default:
+		goto unknown;
+	}
+
+	return config0 & MIPS_CONF_M;
+
+unknown:
+	panic(unknown_isa, config0);
+}
+
+static inline unsigned int decode_config1(struct cpuinfo_mips *c)
+{
+	unsigned int config1;
+
+	config1 = read_c0_config1();
+
+	if (config1 & MIPS_CONF1_MD)
+		c->ases |= MIPS_ASE_MDMX;
+	if (config1 & MIPS_CONF1_WR)
+		c->options |= MIPS_CPU_WATCH;
+	if (config1 & MIPS_CONF1_CA)
+		c->ases |= MIPS_ASE_MIPS16;
+	if (config1 & MIPS_CONF1_EP)
+		c->options |= MIPS_CPU_EJTAG;
+	if (config1 & MIPS_CONF1_FP) {
+		c->options |= MIPS_CPU_FPU;
+		c->options |= MIPS_CPU_32FPR;
+	}
+	if (cpu_has_tlb)
+		c->tlbsize = ((config1 & MIPS_CONF1_TLBS) >> 25) + 1;
+
+	return config1 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config2(struct cpuinfo_mips *c)
+{
+	unsigned int config2;
+
+	config2 = read_c0_config2();
+
+	if (config2 & MIPS_CONF2_SL)
+		c->scache.flags &= ~MIPS_CACHE_NOT_PRESENT;
+
+	return config2 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config3(struct cpuinfo_mips *c)
+{
+	unsigned int config3;
+
+	config3 = read_c0_config3();
+
+	if (config3 & MIPS_CONF3_SM)
+		c->ases |= MIPS_ASE_SMARTMIPS;
+	if (config3 & MIPS_CONF3_DSP)
+		c->ases |= MIPS_ASE_DSP;
+	if (config3 & MIPS_CONF3_VINT)
+		c->options |= MIPS_CPU_VINT;
+	if (config3 & MIPS_CONF3_VEIC)
+		c->options |= MIPS_CPU_VEIC;
+	if (config3 & MIPS_CONF3_MT)
+		c->ases |= MIPS_ASE_MIPSMT;
+	if (config3 & MIPS_CONF3_ULRI)
+		c->options |= MIPS_CPU_ULRI;
+
+	return config3 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config4(struct cpuinfo_mips *c)
+{
+	unsigned int config4;
+
+	config4 = read_c0_config4();
+
+	if ((config4 & MIPS_CONF4_MMUEXTDEF) == MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT
+	    && cpu_has_tlb)
+		c->tlbsize += (config4 & MIPS_CONF4_MMUSIZEEXT) * 0x40;
+
+	c->kscratch_mask = (config4 >> 16) & 0xff;
+
+	return config4 & MIPS_CONF_M;
+}
+
+static void __cpuinit decode_configs(struct cpuinfo_mips *c)
+{
+	int ok;
+
+	/* MIPS32 or MIPS64 compliant CPU.  */
+	c->options = MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE | MIPS_CPU_COUNTER |
+		     MIPS_CPU_DIVEC | MIPS_CPU_LLSC | MIPS_CPU_MCHECK;
+
+	c->scache.flags = MIPS_CACHE_NOT_PRESENT;
+
+	ok = decode_config0(c);			/* Read Config registers.  */
+	BUG_ON(!ok);				/* Arch spec violation!  */
+	if (ok)
+		ok = decode_config1(c);
+	if (ok)
+		ok = decode_config2(c);
+	if (ok)
+		ok = decode_config3(c);
+	if (ok)
+		ok = decode_config4(c);
+
+	mips_probe_watch_registers(c);
+
+	if (cpu_has_mips_r2)
+		c->core = read_c0_ebase() & 0x3ff;
+}
+
 #define R4K_OPTS (MIPS_CPU_TLB | MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE \
 		| MIPS_CPU_COUNTER)
 
@@ -638,155 +787,19 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 			     MIPS_CPU_32FPR;
 		c->tlbsize = 64;
 		break;
-	}
-}
-
-static char unknown_isa[] __cpuinitdata = KERN_ERR \
-	"Unsupported ISA type, c0.config0: %d.";
+	case PRID_IMP_LOONGSON1:
+		decode_configs(c);
 
-static inline unsigned int decode_config0(struct cpuinfo_mips *c)
-{
-	unsigned int config0;
-	int isa;
+		c->cputype = CPU_LOONGSON1;
 
-	config0 = read_c0_config();
-
-	if (((config0 & MIPS_CONF_MT) >> 7) == 1)
-		c->options |= MIPS_CPU_TLB;
-	isa = (config0 & MIPS_CONF_AT) >> 13;
-	switch (isa) {
-	case 0:
-		switch ((config0 & MIPS_CONF_AR) >> 10) {
-		case 0:
-			c->isa_level = MIPS_CPU_ISA_M32R1;
-			break;
-		case 1:
-			c->isa_level = MIPS_CPU_ISA_M32R2;
+		switch (c->processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON1B:
+			__cpu_name[cpu] = "Loongson 1B";
 			break;
-		default:
-			goto unknown;
 		}
-		break;
-	case 2:
-		switch ((config0 & MIPS_CONF_AR) >> 10) {
-		case 0:
-			c->isa_level = MIPS_CPU_ISA_M64R1;
-			break;
-		case 1:
-			c->isa_level = MIPS_CPU_ISA_M64R2;
-			break;
-		default:
-			goto unknown;
-		}
-		break;
-	default:
-		goto unknown;
-	}
-
-	return config0 & MIPS_CONF_M;
-
-unknown:
-	panic(unknown_isa, config0);
-}
 
-static inline unsigned int decode_config1(struct cpuinfo_mips *c)
-{
-	unsigned int config1;
-
-	config1 = read_c0_config1();
-
-	if (config1 & MIPS_CONF1_MD)
-		c->ases |= MIPS_ASE_MDMX;
-	if (config1 & MIPS_CONF1_WR)
-		c->options |= MIPS_CPU_WATCH;
-	if (config1 & MIPS_CONF1_CA)
-		c->ases |= MIPS_ASE_MIPS16;
-	if (config1 & MIPS_CONF1_EP)
-		c->options |= MIPS_CPU_EJTAG;
-	if (config1 & MIPS_CONF1_FP) {
-		c->options |= MIPS_CPU_FPU;
-		c->options |= MIPS_CPU_32FPR;
+		break;
 	}
-	if (cpu_has_tlb)
-		c->tlbsize = ((config1 & MIPS_CONF1_TLBS) >> 25) + 1;
-
-	return config1 & MIPS_CONF_M;
-}
-
-static inline unsigned int decode_config2(struct cpuinfo_mips *c)
-{
-	unsigned int config2;
-
-	config2 = read_c0_config2();
-
-	if (config2 & MIPS_CONF2_SL)
-		c->scache.flags &= ~MIPS_CACHE_NOT_PRESENT;
-
-	return config2 & MIPS_CONF_M;
-}
-
-static inline unsigned int decode_config3(struct cpuinfo_mips *c)
-{
-	unsigned int config3;
-
-	config3 = read_c0_config3();
-
-	if (config3 & MIPS_CONF3_SM)
-		c->ases |= MIPS_ASE_SMARTMIPS;
-	if (config3 & MIPS_CONF3_DSP)
-		c->ases |= MIPS_ASE_DSP;
-	if (config3 & MIPS_CONF3_VINT)
-		c->options |= MIPS_CPU_VINT;
-	if (config3 & MIPS_CONF3_VEIC)
-		c->options |= MIPS_CPU_VEIC;
-	if (config3 & MIPS_CONF3_MT)
-		c->ases |= MIPS_ASE_MIPSMT;
-	if (config3 & MIPS_CONF3_ULRI)
-		c->options |= MIPS_CPU_ULRI;
-
-	return config3 & MIPS_CONF_M;
-}
-
-static inline unsigned int decode_config4(struct cpuinfo_mips *c)
-{
-	unsigned int config4;
-
-	config4 = read_c0_config4();
-
-	if ((config4 & MIPS_CONF4_MMUEXTDEF) == MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT
-	    && cpu_has_tlb)
-		c->tlbsize += (config4 & MIPS_CONF4_MMUSIZEEXT) * 0x40;
-
-	c->kscratch_mask = (config4 >> 16) & 0xff;
-
-	return config4 & MIPS_CONF_M;
-}
-
-static void __cpuinit decode_configs(struct cpuinfo_mips *c)
-{
-	int ok;
-
-	/* MIPS32 or MIPS64 compliant CPU.  */
-	c->options = MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE | MIPS_CPU_COUNTER |
-		     MIPS_CPU_DIVEC | MIPS_CPU_LLSC | MIPS_CPU_MCHECK;
-
-	c->scache.flags = MIPS_CACHE_NOT_PRESENT;
-
-	ok = decode_config0(c);			/* Read Config registers.  */
-	BUG_ON(!ok);				/* Arch spec violation!  */
-	if (ok)
-		ok = decode_config1(c);
-	if (ok)
-		ok = decode_config2(c);
-	if (ok)
-		ok = decode_config3(c);
-	if (ok)
-		ok = decode_config4(c);
-
-	mips_probe_watch_registers(c);
-
-	if (cpu_has_mips_r2)
-		c->core = read_c0_ebase() & 0x3ff;
 }
 
 static inline void cpu_probe_mips(struct cpuinfo_mips *c, unsigned int cpu)

arch/mips/kernel/perf_event_mipsxx.c

@@ -1559,6 +1559,11 @@ init_hw_perf_events(void)
 		mipspmu.general_event_map = &mipsxxcore_event_map;
 		mipspmu.cache_event_map = &mipsxxcore_cache_map;
 		break;
+	case CPU_LOONGSON1:
+		mipspmu.name = "mips/loongson1";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
 	case CPU_CAVIUM_OCTEON:
 	case CPU_CAVIUM_OCTEON_PLUS:
 	case CPU_CAVIUM_OCTEON2:

arch/mips/kernel/prom.c

@@ -35,16 +35,6 @@ void __init early_init_dt_add_memory_arch(u64 base, u64 size)
 	return add_memory_region(base, size, BOOT_MEM_RAM);
 }
 
-int __init reserve_mem_mach(unsigned long addr, unsigned long size)
-{
-	return reserve_bootmem(addr, size, BOOTMEM_DEFAULT);
-}
-
-void __init free_mem_mach(unsigned long addr, unsigned long size)
-{
-	return free_bootmem(addr, size);
-}
-
 void * __init early_init_dt_alloc_memory_arch(u64 size, u64 align)
 {
 	return __alloc_bootmem(size, align, __pa(MAX_DMA_ADDRESS));
@@ -77,25 +67,6 @@ void __init early_init_devtree(void *params)
 	of_scan_flat_dt(early_init_dt_scan_memory_arch, NULL);
 }
 
-void __init device_tree_init(void)
-{
-	unsigned long base, size;
-
-	if (!initial_boot_params)
-		return;
-
-	base = virt_to_phys((void *)initial_boot_params);
-	size = be32_to_cpu(initial_boot_params->totalsize);
-
-	/* Before we do anything, lets reserve the dt blob */
-	reserve_mem_mach(base, size);
-
-	unflatten_device_tree();
-
-	/* free the space reserved for the dt blob */
-	free_mem_mach(base, size);
-}
-
 void __init __dt_setup_arch(struct boot_param_header *bph)
 {
 	if (be32_to_cpu(bph->magic) != OF_DT_HEADER) {

arch/mips/kernel/smp.c

@@ -102,7 +102,9 @@ asmlinkage __cpuinit void start_secondary(void)
 
 #ifdef CONFIG_MIPS_MT_SMTC
 	/* Only do cpu_probe for first TC of CPU */
-	if ((read_c0_tcbind() & TCBIND_CURTC) == 0)
+	if ((read_c0_tcbind() & TCBIND_CURTC) != 0)
+		__cpu_name[smp_processor_id()] = __cpu_name[0];
+	else
 #endif /* CONFIG_MIPS_MT_SMTC */
 	cpu_probe();
 	cpu_report();

arch/mips/kernel/smtc.c

@@ -86,6 +86,13 @@ struct smtc_ipi_q IPIQ[NR_CPUS];
 static struct smtc_ipi_q freeIPIq;
 
 
+/*
+ * Number of FPU contexts for each VPE
+ */
+
+static int smtc_nconf1[MAX_SMTC_VPES];
+
+
 /* Forward declarations */
 
 void ipi_decode(struct smtc_ipi *);
@@ -174,9 +181,9 @@ static int __init tintq(char *str)
 
 __setup("tintq=", tintq);
 
-static int imstuckcount[2][8];
+static int imstuckcount[MAX_SMTC_VPES][8];
 /* vpemask represents IM/IE bits of per-VPE Status registers, low-to-high */
-static int vpemask[2][8] = {
+static int vpemask[MAX_SMTC_VPES][8] = {
 	{0, 0, 1, 0, 0, 0, 0, 1},
 	{0, 0, 0, 0, 0, 0, 0, 1}
 };
@@ -331,6 +338,22 @@ int __init smtc_build_cpu_map(int start_cpu_slot)
 
 static void smtc_tc_setup(int vpe, int tc, int cpu)
 {
+	static int cp1contexts[MAX_SMTC_VPES];
+
+	/*
+	 * Make a local copy of the available FPU contexts in order
+	 * to keep track of TCs that can have one.
+	 */
+	if (tc == 1)
+	{
+		/*
+		 * FIXME: Multi-core SMTC hasn't been tested and the
+		 *        maximum number of VPEs may change.
+		 */
+		cp1contexts[0] = smtc_nconf1[0] - 1;
+		cp1contexts[1] = smtc_nconf1[1];
+	}
+
 	settc(tc);
 	write_tc_c0_tchalt(TCHALT_H);
 	mips_ihb();
@@ -343,22 +366,29 @@ static void smtc_tc_setup(int vpe, int tc, int cpu)
 	 * an active IPI queue.
 	 */
 	write_tc_c0_tccontext((sizeof(struct smtc_ipi_q) * cpu) << 16);
-	/* Bind tc to vpe */
+
+	/* Bind TC to VPE. */
 	write_tc_c0_tcbind(vpe);
+
 	/* In general, all TCs should have the same cpu_data indications. */
 	memcpy(&cpu_data[cpu], &cpu_data[0], sizeof(struct cpuinfo_mips));
-	/* For 34Kf, start with TC/CPU 0 as sole owner of single FPU context */
-	if (cpu_data[0].cputype == CPU_34K ||
-	    cpu_data[0].cputype == CPU_1004K)
+
+	/* Check to see if there is a FPU context available for this TC. */
+	if (!cp1contexts[vpe])
 		cpu_data[cpu].options &= ~MIPS_CPU_FPU;
+	else
+		cp1contexts[vpe]--;
+
+	/* Store the TC and VPE into the cpu_data structure. */
 	cpu_data[cpu].vpe_id = vpe;
 	cpu_data[cpu].tc_id = tc;
-	/* Multi-core SMTC hasn't been tested, but be prepared */
+
+	/* FIXME: Multi-core SMTC hasn't been tested, but be prepared. */
 	cpu_data[cpu].core = (read_vpe_c0_ebase() >> 1) & 0xff;
 }
 
 /*
- * Tweak to get Count registes in as close a sync as possible.  The
+ * Tweak to get Count registers synced as closely as possible. The
  * value seems good for 34K-class cores.
  */
 
@@ -466,6 +496,24 @@ void smtc_prepare_cpus(int cpus)
 	smtc_configure_tlb();
 
 	for (tc = 0, vpe = 0 ; (vpe < nvpe) && (tc < ntc) ; vpe++) {
+		/* Get number of CP1 contexts for each VPE. */
+		if (tc == 0)
+		{
+			/*
+			 * Do not call settc() for TC0 or the FPU context
+			 * value will be incorrect. Besides, we know that
+			 * we are TC0 anyway.
+			 */
+			smtc_nconf1[0] = ((read_vpe_c0_vpeconf1() &
+				VPECONF1_NCP1) >> VPECONF1_NCP1_SHIFT);
+			if (nvpe == 2)
+			{
+				settc(1);
+				smtc_nconf1[1] = ((read_vpe_c0_vpeconf1() &
+					VPECONF1_NCP1) >> VPECONF1_NCP1_SHIFT);
+				settc(0);
+			}
+		}
 		if (tcpervpe[vpe] == 0)
 			continue;
 		if (vpe != 0)
@@ -479,6 +527,18 @@ void smtc_prepare_cpus(int cpus)
 			 */
 			if (tc != 0) {
 				smtc_tc_setup(vpe, tc, cpu);
+				if (vpe != 0) {
+					/*
+					 * Set MVP bit (possibly again).  Do it
+					 * here to catch CPUs that have no TCs
+					 * bound to the VPE at reset.  In that
+					 * case, a TC must be bound to the VPE
+					 * before we can set VPEControl[MVP]
+					 */
+					write_vpe_c0_vpeconf0(
+						read_vpe_c0_vpeconf0() |
+						VPECONF0_MVP);
+				}
 				cpu++;
 			}
 			printk(" %d", tc);

arch/mips/kernel/traps.c

@@ -1253,6 +1253,7 @@ static inline void parity_protection_init(void)
 
 	case CPU_5KC:
 	case CPU_5KE:
+	case CPU_LOONGSON1:
 		write_c0_ecc(0x80000000);
 		back_to_back_c0_hazard();
 		/* Set the PE bit (bit 31) in the c0_errctl register. */

arch/mips/lib/Makefile

@@ -2,7 +2,7 @@
 # Makefile for MIPS-specific library files..
 #
 
-lib-y	+= csum_partial.o delay.o memcpy.o memcpy-inatomic.o memset.o \
+lib-y	+= csum_partial.o delay.o memcpy.o memset.o \
 	   strlen_user.o strncpy_user.o strnlen_user.o uncached.o
 
 obj-y			+= iomap.o

arch/mips/lib/memcpy-inatomic.S

@@ -1,451 +0,0 @@
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Unified implementation of memcpy, memmove and the __copy_user backend.
- *
- * Copyright (C) 1998, 99, 2000, 01, 2002 Ralf Baechle (ralf@gnu.org)
- * Copyright (C) 1999, 2000, 01, 2002 Silicon Graphics, Inc.
- * Copyright (C) 2002 Broadcom, Inc.
- *   memcpy/copy_user author: Mark Vandevoorde
- * Copyright (C) 2007  Maciej W. Rozycki
- *
- * Mnemonic names for arguments to memcpy/__copy_user
- */
-
-/*
- * Hack to resolve longstanding prefetch issue
- *
- * Prefetching may be fatal on some systems if we're prefetching beyond the
- * end of memory on some systems.  It's also a seriously bad idea on non
- * dma-coherent systems.
- */
-#ifdef CONFIG_DMA_NONCOHERENT
-#undef CONFIG_CPU_HAS_PREFETCH
-#endif
-#ifdef CONFIG_MIPS_MALTA
-#undef CONFIG_CPU_HAS_PREFETCH
-#endif
-
-#include <asm/asm.h>
-#include <asm/asm-offsets.h>
-#include <asm/regdef.h>
-
-#define dst a0
-#define src a1
-#define len a2
-
-/*
- * Spec
- *
- * memcpy copies len bytes from src to dst and sets v0 to dst.
- * It assumes that
- *   - src and dst don't overlap
- *   - src is readable
- *   - dst is writable
- * memcpy uses the standard calling convention
- *
- * __copy_user copies up to len bytes from src to dst and sets a2 (len) to
- * the number of uncopied bytes due to an exception caused by a read or write.
- * __copy_user assumes that src and dst don't overlap, and that the call is
- * implementing one of the following:
- *   copy_to_user
- *     - src is readable  (no exceptions when reading src)
- *   copy_from_user
- *     - dst is writable  (no exceptions when writing dst)
- * __copy_user uses a non-standard calling convention; see
- * include/asm-mips/uaccess.h
- *
- * When an exception happens on a load, the handler must
- # ensure that all of the destination buffer is overwritten to prevent
- * leaking information to user mode programs.
- */
-
-/*
- * Implementation
- */
-
-/*
- * The exception handler for loads requires that:
- *  1- AT contain the address of the byte just past the end of the source
- *     of the copy,
- *  2- src_entry <= src < AT, and
- *  3- (dst - src) == (dst_entry - src_entry),
- * The _entry suffix denotes values when __copy_user was called.
- *
- * (1) is set up up by uaccess.h and maintained by not writing AT in copy_user
- * (2) is met by incrementing src by the number of bytes copied
- * (3) is met by not doing loads between a pair of increments of dst and src
- *
- * The exception handlers for stores adjust len (if necessary) and return.
- * These handlers do not need to overwrite any data.
- *
- * For __rmemcpy and memmove an exception is always a kernel bug, therefore
- * they're not protected.
- */
-
-#define EXC(inst_reg,addr,handler)		\
-9:	inst_reg, addr;				\
-	.section __ex_table,"a";		\
-	PTR	9b, handler;			\
-	.previous
-
-/*
- * Only on the 64-bit kernel we can made use of 64-bit registers.
- */
-#ifdef CONFIG_64BIT
-#define USE_DOUBLE
-#endif
-
-#ifdef USE_DOUBLE
-
-#define LOAD   ld
-#define LOADL  ldl
-#define LOADR  ldr
-#define STOREL sdl
-#define STORER sdr
-#define STORE  sd
-#define ADD    daddu
-#define SUB    dsubu
-#define SRL    dsrl
-#define SRA    dsra
-#define SLL    dsll
-#define SLLV   dsllv
-#define SRLV   dsrlv
-#define NBYTES 8
-#define LOG_NBYTES 3
-
-/*
- * As we are sharing code base with the mips32 tree (which use the o32 ABI
- * register definitions). We need to redefine the register definitions from
- * the n64 ABI register naming to the o32 ABI register naming.
- */
-#undef t0
-#undef t1
-#undef t2
-#undef t3
-#define t0	$8
-#define t1	$9
-#define t2	$10
-#define t3	$11
-#define t4	$12
-#define t5	$13
-#define t6	$14
-#define t7	$15
-
-#else
-
-#define LOAD   lw
-#define LOADL  lwl
-#define LOADR  lwr
-#define STOREL swl
-#define STORER swr
-#define STORE  sw
-#define ADD    addu
-#define SUB    subu
-#define SRL    srl
-#define SLL    sll
-#define SRA    sra
-#define SLLV   sllv
-#define SRLV   srlv
-#define NBYTES 4
-#define LOG_NBYTES 2
-
-#endif /* USE_DOUBLE */
-
-#ifdef CONFIG_CPU_LITTLE_ENDIAN
-#define LDFIRST LOADR
-#define LDREST  LOADL
-#define STFIRST STORER
-#define STREST  STOREL
-#define SHIFT_DISCARD SLLV
-#else
-#define LDFIRST LOADL
-#define LDREST  LOADR
-#define STFIRST STOREL
-#define STREST  STORER
-#define SHIFT_DISCARD SRLV
-#endif
-
-#define FIRST(unit) ((unit)*NBYTES)
-#define REST(unit)  (FIRST(unit)+NBYTES-1)
-#define UNIT(unit)  FIRST(unit)
-
-#define ADDRMASK (NBYTES-1)
-
-	.text
-	.set	noreorder
-#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
-	.set	noat
-#else
-	.set	at=v1
-#endif
-
-/*
- * A combined memcpy/__copy_user
- * __copy_user sets len to 0 for success; else to an upper bound of
- * the number of uncopied bytes.
- * memcpy sets v0 to dst.
- */
-	.align	5
-LEAF(__copy_user_inatomic)
-	/*
-	 * Note: dst & src may be unaligned, len may be 0
-	 * Temps
-	 */
-#define rem t8
-
-	/*
-	 * The "issue break"s below are very approximate.
-	 * Issue delays for dcache fills will perturb the schedule, as will
-	 * load queue full replay traps, etc.
-	 *
-	 * If len < NBYTES use byte operations.
-	 */
-	PREF(	0, 0(src) )
-	PREF(	1, 0(dst) )
-	sltu	t2, len, NBYTES
-	and	t1, dst, ADDRMASK
-	PREF(	0, 1*32(src) )
-	PREF(	1, 1*32(dst) )
-	bnez	t2, .Lcopy_bytes_checklen
-	 and	t0, src, ADDRMASK
-	PREF(	0, 2*32(src) )
-	PREF(	1, 2*32(dst) )
-	bnez	t1, .Ldst_unaligned
-	 nop
-	bnez	t0, .Lsrc_unaligned_dst_aligned
-	/*
-	 * use delay slot for fall-through
-	 * src and dst are aligned; need to compute rem
-	 */
-.Lboth_aligned:
-	 SRL	t0, len, LOG_NBYTES+3    	# +3 for 8 units/iter
-	beqz	t0, .Lcleanup_both_aligned	# len < 8*NBYTES
-	 and	rem, len, (8*NBYTES-1)	 	# rem = len % (8*NBYTES)
-	PREF(	0, 3*32(src) )
-	PREF(	1, 3*32(dst) )
-	.align	4
-1:
-EXC(	LOAD	t0, UNIT(0)(src),	.Ll_exc)
-EXC(	LOAD	t1, UNIT(1)(src),	.Ll_exc_copy)
-EXC(	LOAD	t2, UNIT(2)(src),	.Ll_exc_copy)
-EXC(	LOAD	t3, UNIT(3)(src),	.Ll_exc_copy)
-	SUB	len, len, 8*NBYTES
-EXC(	LOAD	t4, UNIT(4)(src),	.Ll_exc_copy)
-EXC(	LOAD	t7, UNIT(5)(src),	.Ll_exc_copy)
-	STORE	t0, UNIT(0)(dst)
-	STORE	t1, UNIT(1)(dst)
-EXC(	LOAD	t0, UNIT(6)(src),	.Ll_exc_copy)
-EXC(	LOAD	t1, UNIT(7)(src),	.Ll_exc_copy)
-	ADD	src, src, 8*NBYTES
-	ADD	dst, dst, 8*NBYTES
-	STORE	t2, UNIT(-6)(dst)
-	STORE	t3, UNIT(-5)(dst)
-	STORE	t4, UNIT(-4)(dst)
-	STORE	t7, UNIT(-3)(dst)
-	STORE	t0, UNIT(-2)(dst)
-	STORE	t1, UNIT(-1)(dst)
-	PREF(	0, 8*32(src) )
-	PREF(	1, 8*32(dst) )
-	bne	len, rem, 1b
-	 nop
-
-	/*
-	 * len == rem == the number of bytes left to copy < 8*NBYTES
-	 */
-.Lcleanup_both_aligned:
-	beqz	len, .Ldone
-	 sltu	t0, len, 4*NBYTES
-	bnez	t0, .Lless_than_4units
-	 and	rem, len, (NBYTES-1)	# rem = len % NBYTES
-	/*
-	 * len >= 4*NBYTES
-	 */
-EXC(	LOAD	t0, UNIT(0)(src),	.Ll_exc)
-EXC(	LOAD	t1, UNIT(1)(src),	.Ll_exc_copy)
-EXC(	LOAD	t2, UNIT(2)(src),	.Ll_exc_copy)
-EXC(	LOAD	t3, UNIT(3)(src),	.Ll_exc_copy)
-	SUB	len, len, 4*NBYTES
-	ADD	src, src, 4*NBYTES
-	STORE	t0, UNIT(0)(dst)
-	STORE	t1, UNIT(1)(dst)
-	STORE	t2, UNIT(2)(dst)
-	STORE	t3, UNIT(3)(dst)
-	.set	reorder				/* DADDI_WAR */
-	ADD	dst, dst, 4*NBYTES
-	beqz	len, .Ldone
-	.set	noreorder
-.Lless_than_4units:
-	/*
-	 * rem = len % NBYTES
-	 */
-	beq	rem, len, .Lcopy_bytes
-	 nop
-1:
-EXC(	LOAD	t0, 0(src),		.Ll_exc)
-	ADD	src, src, NBYTES
-	SUB	len, len, NBYTES
-	STORE	t0, 0(dst)
-	.set	reorder				/* DADDI_WAR */
-	ADD	dst, dst, NBYTES
-	bne	rem, len, 1b
-	.set	noreorder
-
-	/*
-	 * src and dst are aligned, need to copy rem bytes (rem < NBYTES)
-	 * A loop would do only a byte at a time with possible branch
-	 * mispredicts.  Can't do an explicit LOAD dst,mask,or,STORE
-	 * because can't assume read-access to dst.  Instead, use
-	 * STREST dst, which doesn't require read access to dst.
-	 *
-	 * This code should perform better than a simple loop on modern,
-	 * wide-issue mips processors because the code has fewer branches and
-	 * more instruction-level parallelism.
-	 */
-#define bits t2
-	beqz	len, .Ldone
-	 ADD	t1, dst, len	# t1 is just past last byte of dst
-	li	bits, 8*NBYTES
-	SLL	rem, len, 3	# rem = number of bits to keep
-EXC(	LOAD	t0, 0(src),		.Ll_exc)
-	SUB	bits, bits, rem	# bits = number of bits to discard
-	SHIFT_DISCARD t0, t0, bits
-	STREST	t0, -1(t1)
-	jr	ra
-	 move	len, zero
-.Ldst_unaligned:
-	/*
-	 * dst is unaligned
-	 * t0 = src & ADDRMASK
-	 * t1 = dst & ADDRMASK; T1 > 0
-	 * len >= NBYTES
-	 *
-	 * Copy enough bytes to align dst
-	 * Set match = (src and dst have same alignment)
-	 */
-#define match rem
-EXC(	LDFIRST	t3, FIRST(0)(src),	.Ll_exc)
-	ADD	t2, zero, NBYTES
-EXC(	LDREST	t3, REST(0)(src),	.Ll_exc_copy)
-	SUB	t2, t2, t1	# t2 = number of bytes copied
-	xor	match, t0, t1
-	STFIRST t3, FIRST(0)(dst)
-	beq	len, t2, .Ldone
-	 SUB	len, len, t2
-	ADD	dst, dst, t2
-	beqz	match, .Lboth_aligned
-	 ADD	src, src, t2
-
-.Lsrc_unaligned_dst_aligned:
-	SRL	t0, len, LOG_NBYTES+2    # +2 for 4 units/iter
-	PREF(	0, 3*32(src) )
-	beqz	t0, .Lcleanup_src_unaligned
-	 and	rem, len, (4*NBYTES-1)   # rem = len % 4*NBYTES
-	PREF(	1, 3*32(dst) )
-1:
-/*
- * Avoid consecutive LD*'s to the same register since some mips
- * implementations can't issue them in the same cycle.
- * It's OK to load FIRST(N+1) before REST(N) because the two addresses
- * are to the same unit (unless src is aligned, but it's not).
- */
-EXC(	LDFIRST	t0, FIRST(0)(src),	.Ll_exc)
-EXC(	LDFIRST	t1, FIRST(1)(src),	.Ll_exc_copy)
-	SUB     len, len, 4*NBYTES
-EXC(	LDREST	t0, REST(0)(src),	.Ll_exc_copy)
-EXC(	LDREST	t1, REST(1)(src),	.Ll_exc_copy)
-EXC(	LDFIRST	t2, FIRST(2)(src),	.Ll_exc_copy)
-EXC(	LDFIRST	t3, FIRST(3)(src),	.Ll_exc_copy)
-EXC(	LDREST	t2, REST(2)(src),	.Ll_exc_copy)
-EXC(	LDREST	t3, REST(3)(src),	.Ll_exc_copy)
-	PREF(	0, 9*32(src) )		# 0 is PREF_LOAD  (not streamed)
-	ADD	src, src, 4*NBYTES
-#ifdef CONFIG_CPU_SB1
-	nop				# improves slotting
-#endif
-	STORE	t0, UNIT(0)(dst)
-	STORE	t1, UNIT(1)(dst)
-	STORE	t2, UNIT(2)(dst)
-	STORE	t3, UNIT(3)(dst)
-	PREF(	1, 9*32(dst) )     	# 1 is PREF_STORE (not streamed)
-	.set	reorder				/* DADDI_WAR */
-	ADD	dst, dst, 4*NBYTES
-	bne	len, rem, 1b
-	.set	noreorder
-
-.Lcleanup_src_unaligned:
-	beqz	len, .Ldone
-	 and	rem, len, NBYTES-1  # rem = len % NBYTES
-	beq	rem, len, .Lcopy_bytes
-	 nop
-1:
-EXC(	LDFIRST t0, FIRST(0)(src),	.Ll_exc)
-EXC(	LDREST	t0, REST(0)(src),	.Ll_exc_copy)
-	ADD	src, src, NBYTES
-	SUB	len, len, NBYTES
-	STORE	t0, 0(dst)
-	.set	reorder				/* DADDI_WAR */
-	ADD	dst, dst, NBYTES
-	bne	len, rem, 1b
-	.set	noreorder
-
-.Lcopy_bytes_checklen:
-	beqz	len, .Ldone
-	 nop
-.Lcopy_bytes:
-	/* 0 < len < NBYTES  */
-#define COPY_BYTE(N)			\
-EXC(	lb	t0, N(src), .Ll_exc);	\
-	SUB	len, len, 1;		\
-	beqz	len, .Ldone;		\
-	 sb	t0, N(dst)
-
-	COPY_BYTE(0)
-	COPY_BYTE(1)
-#ifdef USE_DOUBLE
-	COPY_BYTE(2)
-	COPY_BYTE(3)
-	COPY_BYTE(4)
-	COPY_BYTE(5)
-#endif
-EXC(	lb	t0, NBYTES-2(src), .Ll_exc)
-	SUB	len, len, 1
-	jr	ra
-	 sb	t0, NBYTES-2(dst)
-.Ldone:
-	jr	ra
-	 nop
-	END(__copy_user_inatomic)
-
-.Ll_exc_copy:
-	/*
-	 * Copy bytes from src until faulting load address (or until a
-	 * lb faults)
-	 *
-	 * When reached by a faulting LDFIRST/LDREST, THREAD_BUADDR($28)
-	 * may be more than a byte beyond the last address.
-	 * Hence, the lb below may get an exception.
-	 *
-	 * Assumes src < THREAD_BUADDR($28)
-	 */
-	LOAD	t0, TI_TASK($28)
-	 nop
-	LOAD	t0, THREAD_BUADDR(t0)
-1:
-EXC(	lb	t1, 0(src),	.Ll_exc)
-	ADD	src, src, 1
-	sb	t1, 0(dst)	# can't fault -- we're copy_from_user
-	.set	reorder				/* DADDI_WAR */
-	ADD	dst, dst, 1
-	bne	src, t0, 1b
-	.set	noreorder
-.Ll_exc:
-	LOAD	t0, TI_TASK($28)
-	 nop
-	LOAD	t0, THREAD_BUADDR(t0)	# t0 is just past last good address
-	 nop
-	SUB	len, AT, t0		# len number of uncopied bytes
-	jr	ra
-	 nop