staging: rtl8192e: Remove dead code

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/rtl8192e/r8192E_dm.c

@@ -440,12 +440,9 @@ static void dm_check_rate_adaptive(struct net_device * dev)
 			}
 		}
 
-		// 2008.04.01
-#if 1
 		// For RTL819X, if pairwisekey = wep/tkip, we support only MCS0~7.
 		if(priv->ieee80211->GetHalfNmodeSupportByAPsHandler(dev))
 			targetRATR &=  0xf00fffff;
-#endif
 
 		//
 		// Check whether updating of RATR0 is required
@@ -2088,7 +2085,6 @@ void dm_init_edca_turbo(struct net_device *dev)
 	priv->bis_cur_rdlstate = false;
 }
 
-#if 1
 static void dm_check_edca_turbo(
 	struct net_device * dev)
 {
@@ -2106,10 +2102,8 @@ static void dm_check_edca_turbo(
 	// Do not be Turbo if it's under WiFi config and Qos Enabled, because the EDCA parameters
 	// should follow the settings from QAP. By Bruce, 2007-12-07.
 	//
-	#if 1
 	if(priv->ieee80211->state != IEEE80211_LINKED)
 		goto dm_CheckEdcaTurbo_EXIT;
-	#endif
 	// We do not turn on EDCA turbo mode for some AP that has IOT issue
 	if(priv->ieee80211->pHTInfo->IOTAction & HT_IOT_ACT_DISABLE_EDCA_TURBO)
 		goto dm_CheckEdcaTurbo_EXIT;
@@ -2197,7 +2191,6 @@ dm_CheckEdcaTurbo_EXIT:
 	lastTxOkCnt = priv->stats.txbytesunicast;
 	lastRxOkCnt = priv->stats.rxbytesunicast;
 }
-#endif
 
 static void dm_init_ctstoself(struct net_device * dev)
 {
@@ -2237,18 +2230,7 @@ static void dm_ctstoself(struct net_device *dev)
 		}
 		else	//uplink
 		{
-		#if 1
 			pHTInfo->IOTAction |= HT_IOT_ACT_FORCED_CTS2SELF;
-		#else
-			if(priv->undecorated_smoothed_pwdb < priv->ieee80211->CTSToSelfTH)	// disable CTS to self
-			{
-				pHTInfo->IOTAction &= ~HT_IOT_ACT_FORCED_CTS2SELF;
-			}
-			else if(priv->undecorated_smoothed_pwdb >= (priv->ieee80211->CTSToSelfTH+5))	// enable CTS to self
-			{
-				pHTInfo->IOTAction |= HT_IOT_ACT_FORCED_CTS2SELF;
-			}
-		#endif
 		}
 
 		lastTxOkCnt = priv->stats.txbytesunicast;
@@ -2259,7 +2241,6 @@ static void dm_ctstoself(struct net_device *dev)
 
 
 /* Copy 8187B template for 9xseries */
-#if 1
 static void dm_check_rfctrl_gpio(struct net_device * dev)
 {
 #ifdef RTL8192E
@@ -2283,7 +2264,6 @@ static void dm_check_rfctrl_gpio(struct net_device * dev)
 
 }
 
-#endif
 /* Check if PBC button is pressed. */
 static	void	dm_check_pbc_gpio(struct net_device *dev)
 {
@@ -3152,7 +3132,6 @@ static void dm_check_txrateandretrycount(struct net_device * dev)
 
 static void dm_send_rssi_tofw(struct net_device *dev)
 {
-	DCMD_TXCMD_T			tx_cmd;
 	struct r8192_priv *priv = ieee80211_priv(dev);
 
 	// If we test chariot, we should stop the TX command ?
@@ -3160,13 +3139,5 @@ static void dm_send_rssi_tofw(struct net_device *dev)
 	// 0x1e0(byte) to botify driver.
 	write_nic_byte(priv, DRIVER_RSSI, (u8)priv->undecorated_smoothed_pwdb);
 	return;
-#if 1
-	tx_cmd.Op		= TXCMD_SET_RX_RSSI;
-	tx_cmd.Length	= 4;
-	tx_cmd.Value		= priv->undecorated_smoothed_pwdb;
-
-	cmpk_message_handle_tx(dev, (u8*)&tx_cmd,
-								DESC_PACKET_TYPE_INIT, sizeof(DCMD_TXCMD_T));
-#endif
 }
 

drivers/staging/rtl8192e/r8192E_wx.c

@@ -693,20 +693,6 @@ static int r8192_wx_set_enc(struct net_device *dev,
 				zero_addr[key_idx],
 				0,                      //DefaultKey
 				hwkey);                 //KeyContent
-
-#if 0
-			if(key_idx == 0){
-
-				//write_nic_byte(dev, SECR, 7);
-				setKey( dev,
-					4,                      //EntryNo
-					key_idx,                      //KeyIndex
-					KEY_TYPE_WEP40,        //KeyType
-					broadcast_addr,         //addr
-					0,                      //DefaultKey
-					hwkey);                 //KeyContent
-			}
-#endif
 		}
 
 		else if(wrqu->encoding.length==0xd){
@@ -719,43 +705,9 @@ static int r8192_wx_set_enc(struct net_device *dev,
 				zero_addr[key_idx],
 				0,                      //DefaultKey
 				hwkey);                 //KeyContent
-#if 0
-			if(key_idx == 0){
-
-				//write_nic_byte(dev, SECR, 7);
-				setKey( dev,
-					4,                      //EntryNo
-					key_idx,                      //KeyIndex
-					KEY_TYPE_WEP104,        //KeyType
-					broadcast_addr,         //addr
-					0,                      //DefaultKey
-					hwkey);                 //KeyContent
-			}
-#endif
 		}
 		else printk("wrong type in WEP, not WEP40 and WEP104\n");
-
-
-	}
-
-#if 0
-	//consider the setting different key index situation
-	//wrqu->encoding.flags = 801 means that we set key with index "1"
-	if(wrqu->encoding.length==0 && (wrqu->encoding.flags >>8) == 0x8 ){
-		printk("===>1\n");
-		//write_nic_byte(dev, SECR, 7);
-		EnableHWSecurityConfig8192(dev);
-		//copy wpa config from default key(key0~key3) to broadcast key(key5)
-		//
-		key_idx = (wrqu->encoding.flags & 0xf)-1 ;
-		write_cam(dev, (4*6),   0xffff0000|read_cam(dev, key_idx*6) );
-		write_cam(dev, (4*6)+1, 0xffffffff);
-		write_cam(dev, (4*6)+2, read_cam(dev, (key_idx*6)+2) );
-		write_cam(dev, (4*6)+3, read_cam(dev, (key_idx*6)+3) );
-		write_cam(dev, (4*6)+4, read_cam(dev, (key_idx*6)+4) );
-		write_cam(dev, (4*6)+5, read_cam(dev, (key_idx*6)+5) );
 	}
-#endif
 
 	priv->ieee80211->wx_set_enc = 0;
 
@@ -929,14 +881,8 @@ static int r8192_wx_set_enc_ext(struct net_device *dev,
 		u32 key[4] = {0};
 		struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
 		struct iw_point *encoding = &wrqu->encoding;
-#if 0
-		static u8 CAM_CONST_ADDR[4][6] = {
-			{0x00, 0x00, 0x00, 0x00, 0x00, 0x00},
-			{0x00, 0x00, 0x00, 0x00, 0x00, 0x01},
-			{0x00, 0x00, 0x00, 0x00, 0x00, 0x02},
-			{0x00, 0x00, 0x00, 0x00, 0x00, 0x03}};
-#endif
 		u8 idx = 0, alg = 0, group = 0;
+
 		if ((encoding->flags & IW_ENCODE_DISABLED) ||
 		ext->alg == IW_ENCODE_ALG_NONE) //none is not allowed to use hwsec WB 2008.07.01
 		{

drivers/staging/rtl8192e/r8192_pm.c

@@ -36,43 +36,8 @@ int rtl8192E_suspend (struct pci_dev *pdev, pm_message_t state)
 
 	if (dev->netdev_ops->ndo_stop)
 		dev->netdev_ops->ndo_stop(dev);
-//	dev->stop(dev);
-#if 0
 
-	netif_carrier_off(dev);
-
-	ieee80211_softmac_stop_protocol(priv->ieee80211);
-
-	write_nic_byte(priv, MSR,(read_nic_byte(dev,MSR)&0xfc)|MSR_LINK_NONE);
-	if(!priv->ieee80211->bSupportRemoteWakeUp) {
-		/* disable tx/rx. In 8185 we write 0x10 (Reset bit),
-		 * but here we make reference to WMAC and wirte 0x0.
-		 * 2006.11.21 Emily
-		 */
-		write_nic_byte(dev, CMDR, 0);
-	}
-	//disable interrupt
-	write_nic_dword(dev,INTA_MASK,0);
-	priv->irq_enabled = 0;
-        write_nic_dword(dev,ISR,read_nic_dword(dev, ISR));
-
-	/* need to  free DM related functions */
-	cancel_work_sync(&priv->reset_wq);
-	del_timer_sync(&priv->fsync_timer);
-	del_timer_sync(&priv->watch_dog_timer);
-	cancel_delayed_work(&priv->watch_dog_wq);
-	cancel_delayed_work(&priv->update_beacon_wq);
-	cancel_work_sync(&priv->qos_activate);
-
-	/* TODO
-#if ((DEV_BUS_TYPE == PCI_INTERFACE) && (HAL_CODE_BASE == RTL8192))
-pHalData->bHwRfOffAction = 2;
-#endif
-*/
-#endif
 	// Call MgntActSet_RF_State instead to prevent RF config race condition.
-	// By Bruce, 2008-01-17.
-	//
 	if(!priv->ieee80211->bSupportRemoteWakeUp) {
 		MgntActSet_RF_State(dev, eRfOff, RF_CHANGE_BY_INIT);
 		// 2006.11.30. System reset bit
@@ -114,8 +79,6 @@ out_pci_suspend:
 int rtl8192E_resume (struct pci_dev *pdev)
 {
 	struct net_device *dev = pci_get_drvdata(pdev);
-	//struct r8192_priv *priv = ieee80211_priv(dev);
-	//union iwreq_data wrqu;
 	int err;
 	u32 val;
 
@@ -155,7 +118,6 @@ int rtl8192E_resume (struct pci_dev *pdev)
 	if (dev->netdev_ops->ndo_open)
 		dev->netdev_ops->ndo_open(dev);
 
-//	dev->open(dev);
 out:
         RT_TRACE(COMP_POWER, "<================r8192E resume call.\n");
 	return 0;

drivers/staging/rtl8192e/r819xE_cmdpkt.c

@@ -189,55 +189,9 @@ cmpk_handle_tx_feedback(
 
 	priv->stats.txfeedback++;
 
-	/* 0. Display received message. */
-	//cmpk_Display_Message(CMPK_RX_TX_FB_SIZE, pMsg);
-
-	/* 1. Extract TX feedback info from RFD to temp structure buffer. */
-	/* It seems that FW use big endian(MIPS) and DRV use little endian in
-	   windows OS. So we have to read the content byte by byte or transfer
-	   endian type before copy the message copy. */
-#if 0		// The TX FEEDBACK packet element address
-	//rx_tx_fb.Element_ID 	= pMsg[0];
-	//rx_tx_fb.Length 		= pMsg[1];
-	rx_tx_fb.TOK 			= pMsg[2]>>7;
-	rx_tx_fb.Fail_Reason 	= (pMsg[2] & 0x70) >> 4;
-	rx_tx_fb.TID 			= (pMsg[2] & 0x0F);
-	rx_tx_fb.Qos_Pkt 		= pMsg[3] >> 7;
-	rx_tx_fb.Bandwidth 		= (pMsg[3] & 0x40) >> 6;
-	rx_tx_fb.Retry_Cnt 		= pMsg[5];
-	rx_tx_fb.Pkt_ID 		= (pMsg[6] << 8) | pMsg[7];
-	rx_tx_fb.Seq_Num 		= (pMsg[8] << 8) | pMsg[9];
-	rx_tx_fb.S_Rate 		= pMsg[10];
-	rx_tx_fb.F_Rate 		= pMsg[11];
-	rx_tx_fb.S_RTS_Rate 	= pMsg[12];
-	rx_tx_fb.F_RTS_Rate 	= pMsg[13];
-	rx_tx_fb.pkt_length	= (pMsg[14] << 8) | pMsg[15];
-#endif
-	/* 2007/07/05 MH Use pointer to transfer structure memory. */
-	//memcpy((UINT8 *)&rx_tx_fb, pMsg, sizeof(CMPK_TXFB_T));
 	memcpy((u8*)&rx_tx_fb, pmsg, sizeof(cmpk_txfb_t));
-	/* 2. Use tx feedback info to count TX statistics. */
+	/* Use tx feedback info to count TX statistics. */
 	cmpk_count_txstatistic(dev, &rx_tx_fb);
-#if 0
-	/* 2007/07/11 MH Assign current operate rate.  */
-	if (pAdapter->RegWirelessMode == WIRELESS_MODE_A ||
-		pAdapter->RegWirelessMode == WIRELESS_MODE_B ||
-		pAdapter->RegWirelessMode == WIRELESS_MODE_G)
-	{
-		pMgntInfo->CurrentOperaRate = (rx_tx_fb.F_Rate & 0x7F);
-	}
-	else if (pAdapter->RegWirelessMode == WIRELESS_MODE_N_24G ||
-		 	 pAdapter->RegWirelessMode == WIRELESS_MODE_N_5G)
-	{
-		pMgntInfo->HTCurrentOperaRate = (rx_tx_fb.F_Rate & 0x8F);
-	}
-#endif
-	/* 2007/01/17 MH Comment previous method for TX statistic function. */
-	/* Collect info TX feedback packet to fill TCB. */
-	/* We can not know the packet length and transmit type: broadcast or uni
-	   or multicast. */
-	//CountTxStatistics( pAdapter, &tcb );
-
 }
 
 
@@ -257,9 +211,6 @@ cmpk_handle_interrupt_status(
 
 	DMESG("---> cmpk_Handle_Interrupt_Status()\n");
 
-	/* 0. Display received message. */
-	//cmpk_Display_Message(CMPK_RX_BEACON_STATE_SIZE, pMsg);
-
 	/* 1. Extract TX feedback info from RFD to temp structure buffer. */
 	/* It seems that FW use big endian(MIPS) and DRV use little endian in
 	   windows OS. So we have to read the content byte by byte or transfer