S3C2410: ensure that FB_BLANK_POWERDOWN shuts down the controller

When a blank level of FB_BLANK_POWERDOWN is used, we should shut down the
controller so that it no longer tries to produce any panel signals or
data, and shuts down the DMA which is not needed.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/s3c2410fb.c

@@ -580,6 +580,27 @@ static int s3c2410fb_setcolreg(unsigned regno,
 	return 0;
 }
 
+/* s3c2410fb_lcd_enable
+ *
+ * shutdown the lcd controller
+ */
+static void s3c2410fb_lcd_enable(struct s3c2410fb_info *fbi, int enable)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	if (enable)
+		fbi->regs.lcdcon1 |= S3C2410_LCDCON1_ENVID;
+	else
+		fbi->regs.lcdcon1 &= ~S3C2410_LCDCON1_ENVID;
+
+	writel(fbi->regs.lcdcon1, fbi->io + S3C2410_LCDCON1);
+
+	local_irq_restore(flags);
+}
+
+
 /*
  *      s3c2410fb_blank
  *	@blank_mode: the blank mode we want.
@@ -589,9 +610,6 @@ static int s3c2410fb_setcolreg(unsigned regno,
  *	blanking succeeded, != 0 if un-/blanking failed due to e.g. a
  *	video mode which doesn't support it. Implements VESA suspend
  *	and powerdown modes on hardware that supports disabling hsync/vsync:
- *	blank_mode == 2: suspend vsync
- *	blank_mode == 3: suspend hsync
- *	blank_mode == 4: powerdown
  *
  *	Returns negative errno on error, or zero on success.
  *
@@ -605,6 +623,12 @@ static int s3c2410fb_blank(int blank_mode, struct fb_info *info)
 
 	tpal_reg += is_s3c2412(fbi) ? S3C2412_TPAL : S3C2410_TPAL;
 
+	if (blank_mode == FB_BLANK_POWERDOWN) {
+		s3c2410fb_lcd_enable(fbi, 0);
+	} else {
+		s3c2410fb_lcd_enable(fbi, 1);
+	}
+
 	if (blank_mode == FB_BLANK_UNBLANK)
 		writel(0x0, tpal_reg);
 	else {
@@ -983,21 +1007,6 @@ static int __init s3c2412fb_probe(struct platform_device *pdev)
 	return s3c24xxfb_probe(pdev, DRV_S3C2412);
 }
 
-/* s3c2410fb_stop_lcd
- *
- * shutdown the lcd controller
- */
-static void s3c2410fb_stop_lcd(struct s3c2410fb_info *fbi)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	fbi->regs.lcdcon1 &= ~S3C2410_LCDCON1_ENVID;
-	writel(fbi->regs.lcdcon1, fbi->io + S3C2410_LCDCON1);
-
-	local_irq_restore(flags);
-}
 
 /*
  *  Cleanup
@@ -1010,7 +1019,7 @@ static int s3c2410fb_remove(struct platform_device *pdev)
 
 	unregister_framebuffer(fbinfo);
 
-	s3c2410fb_stop_lcd(info);
+	s3c2410fb_lcd_enable(info, 0);
 	msleep(1);
 
 	s3c2410fb_unmap_video_memory(fbinfo);
@@ -1043,7 +1052,7 @@ static int s3c2410fb_suspend(struct platform_device *dev, pm_message_t state)
 	struct fb_info	   *fbinfo = platform_get_drvdata(dev);
 	struct s3c2410fb_info *info = fbinfo->par;
 
-	s3c2410fb_stop_lcd(info);
+	s3c2410fb_lcd_enable(info, 0);
 
 	/* sleep before disabling the clock, we need to ensure
 	 * the LCD DMA engine is not going to get back on the bus