ARM: signal: sigreturn_codes should be endian neutral to work in BE8

In case of BE8 kernel data is in BE order whereas code stays in LE
order. Move sigreturn_codes to separate .S file and use proper
assembler mnemonics for these code snippets. In this case compiler
will take care of proper instructions byteswaps for BE8 case.
Change assumes that sufficiently Thumb-capable tools are used to
build kernel.

Problem was discovered during ltp testing of BE system: all rt_sig*
tests failed. Tested against the same tests in both BE and LE modes.

Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>

arch/arm/kernel/Makefile

@@ -17,7 +17,8 @@ CFLAGS_REMOVE_return_address.o = -pg
 
 obj-y		:= elf.o entry-common.o irq.o opcodes.o \
 		   process.o ptrace.o return_address.o \
-		   setup.o signal.o stacktrace.o sys_arm.o time.o traps.o
+		   setup.o signal.o sigreturn_codes.o \
+		   stacktrace.o sys_arm.o time.o traps.o
 
 obj-$(CONFIG_ATAGS)		+= atags_parse.o
 obj-$(CONFIG_ATAGS_PROC)	+= atags_proc.o

arch/arm/kernel/signal.c

@@ -21,29 +21,7 @@
 #include <asm/unistd.h>
 #include <asm/vfp.h>
 
-/*
- * For ARM syscalls, we encode the syscall number into the instruction.
- */
-#define SWI_SYS_SIGRETURN	(0xef000000|(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-#define SWI_SYS_RT_SIGRETURN	(0xef000000|(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE))
-
-/*
- * With EABI, the syscall number has to be loaded into r7.
- */
-#define MOV_R7_NR_SIGRETURN	(0xe3a07000 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define MOV_R7_NR_RT_SIGRETURN	(0xe3a07000 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-/*
- * For Thumb syscalls, we pass the syscall number via r7.  We therefore
- * need two 16-bit instructions.
- */
-#define SWI_THUMB_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_sigreturn - __NR_SYSCALL_BASE))
-#define SWI_THUMB_RT_SIGRETURN	(0xdf00 << 16 | 0x2700 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-
-static const unsigned long sigreturn_codes[7] = {
-	MOV_R7_NR_SIGRETURN,    SWI_SYS_SIGRETURN,    SWI_THUMB_SIGRETURN,
-	MOV_R7_NR_RT_SIGRETURN, SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN,
-};
+extern const unsigned long sigreturn_codes[7];
 
 static unsigned long signal_return_offset;
 

arch/arm/kernel/sigreturn_codes.S

@@ -0,0 +1,80 @@
+/*
+ * sigreturn_codes.S - code sinpets for sigreturn syscalls
+ *
+ * Created by:	Victor Kamensky, 2013-08-13
+ * Copyright:	(C) 2013  Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/unistd.h>
+
+/*
+ * For ARM syscalls, we encode the syscall number into the instruction.
+ * With EABI, the syscall number has to be loaded into r7. As result
+ * ARM syscall sequence snippet will have move and svc in .arm encoding
+ *
+ * For Thumb syscalls, we pass the syscall number via r7.  We therefore
+ * need two 16-bit instructions in .thumb encoding
+ *
+ * Please note sigreturn_codes code are not executed in place. Instead
+ * they just copied by kernel into appropriate places. Code inside of
+ * arch/arm/kernel/signal.c is very sensitive to layout of these code
+ * snippets.
+ */
+
+#if __LINUX_ARM_ARCH__ <= 4
+	/*
+	 * Note we manually set minimally required arch that supports
+	 * required thumb opcodes for early arch versions. It is OK
+	 * for this file to be used in combination with other
+	 * lower arch variants, since these code snippets are only
+	 * used as input data.
+	 */
+	.arch armv4t
+#endif
+
+	.section .rodata
+	.global sigreturn_codes
+	.type	sigreturn_codes, #object
+
+	.arm
+
+sigreturn_codes:
+
+	/* ARM sigreturn syscall code snippet */
+	mov	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/* ARM sigreturn_rt syscall code snippet */
+	.arm
+	mov	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE)
+
+	/* Thumb sigreturn_rt syscall code snippet */
+	.thumb
+	movs	r7, #(__NR_rt_sigreturn - __NR_SYSCALL_BASE)
+	swi	#0
+
+	/*
+	 * Note on addtional space: setup_return in signal.c
+	 * algorithm uses two words copy regardless whether
+	 * it is thumb case or not, so we need additional
+	 * word after real last entry.
+	 */
+	.arm
+	.space	4
+
+	.size	sigreturn_codes, . - sigreturn_codes