Merge branch 'sched/urgent'; commit 'v2.6.28' into sched/core

Documentation/arm/mem_alignment

@@ -24,7 +24,7 @@ real bad - it changes the behaviour of all unaligned instructions in user
 space, and might cause programs to fail unexpectedly.
 
 To change the alignment trap behavior, simply echo a number into
-/proc/sys/debug/alignment.  The number is made up from various bits:
+/proc/cpu/alignment.  The number is made up from various bits:
 
 bit		behavior when set
 ---		-----------------

Documentation/kernel-parameters.txt

@@ -220,14 +220,17 @@ and is between 256 and 4096 characters. It is defined in the file
 			Bits in debug_level correspond to a level in
 			ACPI_DEBUG_PRINT statements, e.g.,
 			    ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
-			See Documentation/acpi/debug.txt for more information
-			about debug layers and levels.
+			The debug_level mask defaults to "info".  See
+			Documentation/acpi/debug.txt for more information about
+			debug layers and levels.
 
+			Enable processor driver info messages:
+			    acpi.debug_layer=0x20000000
+			Enable PCI/PCI interrupt routing info messages:
+			    acpi.debug_layer=0x400000
 			Enable AML "Debug" output, i.e., stores to the Debug
 			object while interpreting AML:
 			    acpi.debug_layer=0xffffffff acpi.debug_level=0x2
-			Enable PCI/PCI interrupt routing info messages:
-			    acpi.debug_layer=0x400000 acpi.debug_level=0x4
 			Enable all messages related to ACPI hardware:
 			    acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
 

Documentation/sound/alsa/ALSA-Configuration.txt

@@ -1063,6 +1063,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
 	STAC9227/9228/9229/927x
 	  ref		Reference board
+	  ref-no-jd	Reference board without HP/Mic jack detection
 	  3stack	D965 3stack
 	  5stack	D965 5stack + SPDIF
 	  dell-3stack	Dell Dimension E520
@@ -1076,6 +1077,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
 
 	STAC92HD73*
 	  ref		Reference board
+	  no-jd		BIOS setup but without jack-detection
 	  dell-m6-amic	Dell desktops/laptops with analog mics
 	  dell-m6-dmic	Dell desktops/laptops with digital mics
 	  dell-m6	Dell desktops/laptops with both type of mics

Documentation/usb/gadget_serial.txt

@@ -114,11 +114,11 @@ modules.
 Then you must load the gadget serial driver.  To load it as an
 ACM device (recommended for interoperability), do this:
 
-  modprobe g_serial use_acm=1
+  modprobe g_serial
 
 To load it as a vendor specific bulk in/out device, do this:
 
-  modprobe g_serial
+  modprobe g_serial use_acm=0
 
 This will also automatically load the underlying gadget peripheral
 controller driver.  This must be done each time you reboot the gadget

Documentation/usb/proc_usb_info.txt

@@ -49,8 +49,10 @@ it and 002/048 sometime later.
 
 These files can be read as binary data.  The binary data consists
 of first the device descriptor, then the descriptors for each
-configuration of the device.  That information is also shown in
-text form by the /proc/bus/usb/devices file, described later.
+configuration of the device.  Multi-byte fields in the device and
+configuration descriptors, but not other descriptors, are converted
+to host endianness by the kernel.  This information is also shown
+in text form by the /proc/bus/usb/devices file, described later.
 
 These files may also be used to write user-level drivers for the USB
 devices.  You would open the /proc/bus/usb/BBB/DDD file read/write,

Documentation/usb/usbmon.txt

@@ -34,11 +34,12 @@ if usbmon is built into the kernel.
 Verify that bus sockets are present.
 
 # ls /sys/kernel/debug/usbmon
-0s  0t  0u  1s  1t  1u  2s  2t  2u  3s  3t  3u  4s  4t  4u
+0s  0u  1s  1t  1u  2s  2t  2u  3s  3t  3u  4s  4t  4u
 #
 
-Now you can choose to either use the sockets numbered '0' (to capture packets on
-all buses), and skip to step #3, or find the bus used by your device with step #2.
+Now you can choose to either use the socket '0u' (to capture packets on all
+buses), and skip to step #3, or find the bus used by your device with step #2.
+This allows to filter away annoying devices that talk continuously.
 
 2. Find which bus connects to the desired device
 
@@ -99,8 +100,9 @@ on the event type, but there is a set of words, common for all types.
 
 Here is the list of words, from left to right:
 
-- URB Tag. This is used to identify URBs is normally a kernel mode address
- of the URB structure in hexadecimal.
+- URB Tag. This is used to identify URBs, and is normally an in-kernel address
+  of the URB structure in hexadecimal, but can be a sequence number or any
+  other unique string, within reason.
 
 - Timestamp in microseconds, a decimal number. The timestamp's resolution
   depends on available clock, and so it can be much worse than a microsecond

MAINTAINERS

@@ -1527,10 +1527,10 @@ W:	http://ebtables.sourceforge.net/
 S:	Maintained
 
 ECRYPT FILE SYSTEM
-P:	Mike Halcrow, Phillip Hellewell
-M:	mhalcrow@us.ibm.com, phillip@hellewell.homeip.net
-L:	ecryptfs-devel@lists.sourceforge.net
-W:	http://ecryptfs.sourceforge.net/
+P:	Tyler Hicks, Dustin Kirkland
+M:	tyhicks@linux.vnet.ibm.com, kirkland@canonical.com
+L:	ecryptfs-devel@lists.launchpad.net
+W:	https://launchpad.net/ecryptfs
 S:	Supported
 
 EDAC-CORE
@@ -2191,9 +2191,9 @@ S:	Supported
 
 INOTIFY
 P:	John McCutchan
-M:	ttb@tentacle.dhs.org
+M:	john@johnmccutchan.com
 P:	Robert Love
-M:	rml@novell.com
+M:	rlove@rlove.org
 L:	linux-kernel@vger.kernel.org
 S:	Maintained
 
@@ -4529,7 +4529,7 @@ S:	Maintained
 USB VIDEO CLASS
 P:	Laurent Pinchart
 M:	laurent.pinchart@skynet.be
-L:	linux-uvc-devel@lists.berlios.de
+L:	linux-uvc-devel@lists.berlios.de (subscribers-only)
 L:	video4linux-list@redhat.com
 W:	http://linux-uvc.berlios.de
 S:	Maintained

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 28
-EXTRAVERSION = -rc8
+EXTRAVERSION =
 NAME = Erotic Pickled Herring
 
 # *DOCUMENTATION*

arch/arm/common/sa1111.c

@@ -630,7 +630,7 @@ __sa1111_probe(struct device *me, struct resource *mem, int irq)
 		return -ENOMEM;
 
 	sachip->clk = clk_get(me, "SA1111_CLK");
-	if (!sachip->clk) {
+	if (IS_ERR(sachip->clk)) {
 		ret = PTR_ERR(sachip->clk);
 		goto err_free;
 	}

arch/arm/kernel/armksyms.c

@@ -115,6 +115,8 @@ EXPORT_SYMBOL(__strnlen_user);
 EXPORT_SYMBOL(__strncpy_from_user);
 
 #ifdef CONFIG_MMU
+EXPORT_SYMBOL(copy_page);
+
 EXPORT_SYMBOL(__copy_from_user);
 EXPORT_SYMBOL(__copy_to_user);
 EXPORT_SYMBOL(__clear_user);
@@ -181,8 +183,6 @@ EXPORT_SYMBOL(_find_first_bit_be);
 EXPORT_SYMBOL(_find_next_bit_be);
 #endif
 
-EXPORT_SYMBOL(copy_page);
-
 #ifdef CONFIG_FUNCTION_TRACER
 EXPORT_SYMBOL(mcount);
 #endif

arch/arm/kernel/traps.c

@@ -18,6 +18,7 @@
 #include <linux/personality.h>
 #include <linux/kallsyms.h>
 #include <linux/delay.h>
+#include <linux/hardirq.h>
 #include <linux/init.h>
 #include <linux/uaccess.h>
 

arch/arm/mach-pxa/include/mach/reset.h

@@ -12,9 +12,8 @@ extern void clear_reset_status(unsigned int mask);
 
 /**
  * init_gpio_reset() - register GPIO as reset generator
- *
- * @gpio - gpio nr
- * @output - set gpio as out/low instead of input during normal work
+ * @gpio: gpio nr
+ * @output: set gpio as out/low instead of input during normal work
  */
 extern int init_gpio_reset(int gpio, int output);
 

arch/arm/mm/fault.c

@@ -11,6 +11,7 @@
 #include <linux/module.h>
 #include <linux/signal.h>
 #include <linux/mm.h>
+#include <linux/hardirq.h>
 #include <linux/init.h>
 #include <linux/kprobes.h>
 #include <linux/uaccess.h>

arch/avr32/boards/favr-32/flash.c

@@ -13,7 +13,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 
-#include <asm/arch/smc.h>
+#include <mach/smc.h>
 
 static struct smc_timing flash_timing __initdata = {
 	.ncs_read_setup		= 0,

arch/avr32/boards/favr-32/setup.c

@@ -25,10 +25,10 @@
 
 #include <asm/setup.h>
 
-#include <asm/arch/at32ap700x.h>
-#include <asm/arch/init.h>
-#include <asm/arch/board.h>
-#include <asm/arch/portmux.h>
+#include <mach/at32ap700x.h>
+#include <mach/init.h>
+#include <mach/board.h>
+#include <mach/portmux.h>
 
 /* Oscillator frequencies. These are board-specific */
 unsigned long at32_board_osc_rates[3] = {

arch/avr32/boot/images/Makefile

@@ -10,7 +10,7 @@ MKIMAGE		:= $(srctree)/scripts/mkuboot.sh
 
 extra-y		:= vmlinux.bin vmlinux.gz
 
-OBJCOPYFLAGS_vmlinux.bin := -O binary
+OBJCOPYFLAGS_vmlinux.bin := -O binary -R .note.gnu.build-id
 $(obj)/vmlinux.bin: vmlinux FORCE
 	$(call if_changed,objcopy)
 

arch/avr32/configs/atstk1006_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.27-rc1
-# Tue Aug  5 15:40:26 2008
+# Linux kernel version: 2.6.28-rc8
+# Thu Dec 18 11:22:23 2008
 #
 CONFIG_AVR32=y
 CONFIG_GENERIC_GPIO=y
@@ -67,6 +67,7 @@ CONFIG_SIGNALFD=y
 CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
+CONFIG_AIO=y
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_SLUB_DEBUG=y
 # CONFIG_SLAB is not set
@@ -77,15 +78,8 @@ CONFIG_PROFILING=y
 CONFIG_OPROFILE=m
 CONFIG_HAVE_OPROFILE=y
 CONFIG_KPROBES=y
-# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set
-# CONFIG_HAVE_IOREMAP_PROT is not set
 CONFIG_HAVE_KPROBES=y
-# CONFIG_HAVE_KRETPROBES is not set
-# CONFIG_HAVE_ARCH_TRACEHOOK is not set
-# CONFIG_HAVE_DMA_ATTRS is not set
-# CONFIG_USE_GENERIC_SMP_HELPERS is not set
 CONFIG_HAVE_CLK=y
-CONFIG_PROC_PAGE_MONITOR=y
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
@@ -118,6 +112,7 @@ CONFIG_DEFAULT_CFQ=y
 # CONFIG_DEFAULT_NOOP is not set
 CONFIG_DEFAULT_IOSCHED="cfq"
 CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
 
 #
 # System Type and features
@@ -134,6 +129,8 @@ CONFIG_CPU_AT32AP700X=y
 CONFIG_CPU_AT32AP7000=y
 CONFIG_BOARD_ATSTK1000=y
 # CONFIG_BOARD_ATNGW100 is not set
+# CONFIG_BOARD_FAVR_32 is not set
+# CONFIG_BOARD_MIMC200 is not set
 # CONFIG_BOARD_ATSTK1002 is not set
 # CONFIG_BOARD_ATSTK1003 is not set
 # CONFIG_BOARD_ATSTK1004 is not set
@@ -171,14 +168,14 @@ CONFIG_FLATMEM_MANUAL=y
 # CONFIG_SPARSEMEM_MANUAL is not set
 CONFIG_FLATMEM=y
 CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
 CONFIG_PAGEFLAGS_EXTENDED=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_RESOURCES_64BIT is not set
+# CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_NR_QUICK=2
 CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
 # CONFIG_OWNERSHIP_TRACE is not set
 CONFIG_NMI_DEBUGGING=y
 # CONFIG_HZ_100 is not set
@@ -186,7 +183,7 @@ CONFIG_HZ_250=y
 # CONFIG_HZ_300 is not set
 # CONFIG_HZ_1000 is not set
 CONFIG_HZ=250
-# CONFIG_SCHED_HRTICK is not set
+CONFIG_SCHED_HRTICK=y
 CONFIG_CMDLINE=""
 
 #
@@ -228,6 +225,8 @@ CONFIG_CPU_FREQ_AT32AP=y
 # Executable file formats
 #
 CONFIG_BINFMT_ELF=y
+CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
+# CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 CONFIG_NET=y
 
@@ -299,6 +298,7 @@ CONFIG_IPV6_TUNNEL=m
 # CONFIG_ATM is not set
 CONFIG_STP=m
 CONFIG_BRIDGE=m
+# CONFIG_NET_DSA is not set
 # CONFIG_VLAN_8021Q is not set
 # CONFIG_DECNET is not set
 CONFIG_LLC=m
@@ -321,14 +321,8 @@ CONFIG_LLC=m
 # CONFIG_IRDA is not set
 # CONFIG_BT is not set
 # CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
+# CONFIG_PHONET is not set
+# CONFIG_WIRELESS is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
 
@@ -359,6 +353,7 @@ CONFIG_MTD_CMDLINE_PARTS=y
 # User Modules And Translation Layers
 #
 CONFIG_MTD_CHAR=y
+CONFIG_HAVE_MTD_OTP=y
 CONFIG_MTD_BLKDEVS=y
 CONFIG_MTD_BLOCK=y
 # CONFIG_FTL is not set
@@ -407,6 +402,8 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2
 # Self-contained MTD device drivers
 #
 CONFIG_MTD_DATAFLASH=m
+# CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set
+CONFIG_MTD_DATAFLASH_OTP=y
 CONFIG_MTD_M25P80=m
 CONFIG_M25PXX_USE_FAST_READ=y
 # CONFIG_MTD_SLRAM is not set
@@ -464,9 +461,10 @@ CONFIG_ATMEL_TCLIB=y
 CONFIG_ATMEL_TCB_CLKSRC=y
 CONFIG_ATMEL_TCB_CLKSRC_BLOCK=0
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ICS932S401 is not set
 CONFIG_ATMEL_SSC=m
 # CONFIG_ENCLOSURE_SERVICES is not set
-# CONFIG_HAVE_IDE is not set
+# CONFIG_C2PORT is not set
 
 #
 # SCSI device support
@@ -548,6 +546,9 @@ CONFIG_MACB=y
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
 # CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
 # CONFIG_NETDEV_1000 is not set
 # CONFIG_NETDEV_10000 is not set
@@ -653,6 +654,7 @@ CONFIG_UNIX98_PTYS=y
 CONFIG_I2C=m
 CONFIG_I2C_BOARDINFO=y
 CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
 CONFIG_I2C_ALGOBIT=m
 
 #
@@ -716,6 +718,10 @@ CONFIG_GPIOLIB=y
 # CONFIG_DEBUG_GPIO is not set
 CONFIG_GPIO_SYSFS=y
 
+#
+# Memory mapped GPIO expanders:
+#
+
 #
 # I2C GPIO expanders:
 #
@@ -745,11 +751,11 @@ CONFIG_WATCHDOG=y
 #
 # CONFIG_SOFT_WATCHDOG is not set
 CONFIG_AT32AP700X_WDT=y
+CONFIG_SSB_POSSIBLE=y
 
 #
 # Sonics Silicon Backplane
 #
-CONFIG_SSB_POSSIBLE=y
 # CONFIG_SSB is not set
 
 #
@@ -758,6 +764,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
 
 #
 # Multimedia devices
@@ -783,6 +793,7 @@ CONFIG_SSB_POSSIBLE=y
 CONFIG_FB=y
 # CONFIG_FIRMWARE_EDID is not set
 # CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
 CONFIG_FB_CFB_FILLRECT=y
 CONFIG_FB_CFB_COPYAREA=y
 CONFIG_FB_CFB_IMAGEBLIT=y
@@ -804,10 +815,13 @@ CONFIG_FB_CFB_IMAGEBLIT=y
 # CONFIG_FB_S1D13XXX is not set
 CONFIG_FB_ATMEL=y
 # CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_LTV350QV=y
 # CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
 # CONFIG_LCD_VGG2432A4 is not set
 # CONFIG_LCD_PLATFORM is not set
 # CONFIG_BACKLIGHT_CLASS_DEVICE is not set
@@ -818,6 +832,7 @@ CONFIG_LCD_LTV350QV=y
 # CONFIG_DISPLAY_SUPPORT is not set
 # CONFIG_LOGO is not set
 CONFIG_SOUND=m
+CONFIG_SOUND_OSS_CORE=y
 CONFIG_SND=m
 CONFIG_SND_TIMER=m
 CONFIG_SND_PCM=m
@@ -848,28 +863,32 @@ CONFIG_USB_SUPPORT=y
 # CONFIG_USB_ARCH_HAS_EHCI is not set
 # CONFIG_USB_OTG_WHITELIST is not set
 # CONFIG_USB_OTG_BLACKLIST_HUB is not set
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
 #
 CONFIG_USB_GADGET=y
 # CONFIG_USB_GADGET_DEBUG is not set
 # CONFIG_USB_GADGET_DEBUG_FILES is not set
 # CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
 CONFIG_USB_GADGET_SELECTED=y
-# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_AT91 is not set
 CONFIG_USB_GADGET_ATMEL_USBA=y
 CONFIG_USB_ATMEL_USBA=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
-# CONFIG_USB_GADGET_NET2280 is not set
-# CONFIG_USB_GADGET_PXA25X is not set
-# CONFIG_USB_GADGET_M66592 is not set
-# CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_GOKU is not set
 # CONFIG_USB_GADGET_LH7A40X is not set
 # CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_S3C2410 is not set
-# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
 # CONFIG_USB_GADGET_DUMMY_HCD is not set
 CONFIG_USB_GADGET_DUALSPEED=y
 CONFIG_USB_ZERO=m
@@ -887,7 +906,7 @@ CONFIG_MMC=y
 # CONFIG_MMC_UNSAFE_RESUME is not set
 
 #
-# MMC/SD Card Drivers
+# MMC/SD/SDIO Card Drivers
 #
 CONFIG_MMC_BLOCK=y
 CONFIG_MMC_BLOCK_BOUNCE=y
@@ -895,10 +914,11 @@ CONFIG_MMC_BLOCK_BOUNCE=y
 # CONFIG_MMC_TEST is not set
 
 #
-# MMC/SD Host Controller Drivers
+# MMC/SD/SDIO Host Controller Drivers
 #
 # CONFIG_MMC_SDHCI is not set
 CONFIG_MMC_ATMELMCI=y
+# CONFIG_MMC_ATMELMCI_DMA is not set
 CONFIG_MMC_SPI=m
 # CONFIG_MEMSTICK is not set
 CONFIG_NEW_LEDS=y
@@ -918,6 +938,7 @@ CONFIG_LEDS_GPIO=m
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=m
 CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
 CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
 # CONFIG_ACCESSIBILITY is not set
 CONFIG_RTC_LIB=y
@@ -950,25 +971,31 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
 
 #
 # SPI RTC drivers
 #
 # CONFIG_RTC_DRV_M41T94 is not set
 # CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
 # CONFIG_RTC_DRV_MAX6902 is not set
 # CONFIG_RTC_DRV_R9701 is not set
 # CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
 
 #
 # Platform RTC drivers
 #
+# CONFIG_RTC_DRV_DS1286 is not set
 # CONFIG_RTC_DRV_DS1511 is not set
 # CONFIG_RTC_DRV_DS1553 is not set
 # CONFIG_RTC_DRV_DS1742 is not set
 # CONFIG_RTC_DRV_STK17TA8 is not set
 # CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
 # CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
 # CONFIG_RTC_DRV_V3020 is not set
 
 #
@@ -989,6 +1016,8 @@ CONFIG_DMA_ENGINE=y
 # CONFIG_NET_DMA is not set
 CONFIG_DMATEST=m
 # CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+CONFIG_STAGING_EXCLUDE_BUILD=y
 
 #
 # File systems
@@ -998,12 +1027,17 @@ CONFIG_EXT2_FS=m
 # CONFIG_EXT2_FS_XIP is not set
 CONFIG_EXT3_FS=m
 # CONFIG_EXT3_FS_XATTR is not set
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4_FS=m
+CONFIG_EXT4DEV_COMPAT=y
+# CONFIG_EXT4_FS_XATTR is not set
 CONFIG_JBD=m
 # CONFIG_JBD_DEBUG is not set
+CONFIG_JBD2=m
+# CONFIG_JBD2_DEBUG is not set
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
+CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_DNOTIFY is not set
@@ -1036,6 +1070,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
 CONFIG_PROC_FS=y
 CONFIG_PROC_KCORE=y
 CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
 CONFIG_SYSFS=y
 CONFIG_TMPFS=y
 # CONFIG_TMPFS_POSIX_ACL is not set
@@ -1054,7 +1089,8 @@ CONFIG_TMPFS=y
 # CONFIG_EFS_FS is not set
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_FS_DEBUG=0
-# CONFIG_JFFS2_FS_WRITEBUFFER is not set
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
 # CONFIG_JFFS2_SUMMARY is not set
 # CONFIG_JFFS2_FS_XATTR is not set
 # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
@@ -1088,6 +1124,7 @@ CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
+# CONFIG_SUNRPC_REGISTER_V4 is not set
 # CONFIG_RPCSEC_GSS_KRB5 is not set
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
 # CONFIG_SMB_FS is not set
@@ -1185,10 +1222,21 @@ CONFIG_DEBUG_BUGVERBOSE=y
 CONFIG_FRAME_POINTER=y
 # CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_KPROBES_SANITY_TEST is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
 # CONFIG_LKDTM is not set
 # CONFIG_FAULT_INJECTION is not set
+
+#
+# Tracers
+#
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
 # CONFIG_SAMPLES is not set
 
 #
@@ -1196,17 +1244,26 @@ CONFIG_FRAME_POINTER=y
 #
 # CONFIG_KEYS is not set
 # CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
 CONFIG_CRYPTO=y
 
 #
 # Crypto core or helper
 #
+CONFIG_CRYPTO_FIPS=y
 CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
 CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=y
 CONFIG_CRYPTO_BLKCIPHER=m
+CONFIG_CRYPTO_BLKCIPHER2=y
 CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
 CONFIG_CRYPTO_MANAGER=m
+CONFIG_CRYPTO_MANAGER2=y
 # CONFIG_CRYPTO_GF128MUL is not set
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_CRYPTD is not set
@@ -1257,7 +1314,7 @@ CONFIG_CRYPTO_SHA1=m
 #
 # Ciphers
 #
-# CONFIG_CRYPTO_AES is not set
+CONFIG_CRYPTO_AES=m
 # CONFIG_CRYPTO_ANUBIS is not set
 # CONFIG_CRYPTO_ARC4 is not set
 # CONFIG_CRYPTO_BLOWFISH is not set
@@ -1278,14 +1335,17 @@ CONFIG_CRYPTO_DES=m
 #
 CONFIG_CRYPTO_DEFLATE=y
 CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
 # CONFIG_CRYPTO_HW is not set
 
 #
 # Library routines
 #
 CONFIG_BITREVERSE=y
-# CONFIG_GENERIC_FIND_FIRST_BIT is not set
-# CONFIG_GENERIC_FIND_NEXT_BIT is not set
 CONFIG_CRC_CCITT=m
 CONFIG_CRC16=y
 CONFIG_CRC_T10DIF=m

arch/avr32/mach-at32ap/at32ap700x.c

@@ -967,28 +967,28 @@ static inline void configure_usart0_pins(void)
 {
 	u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */
 
-	select_peripheral(PIOA, pin_mask, PERIPH_B, 0);
+	select_peripheral(PIOA, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
 }
 
 static inline void configure_usart1_pins(void)
 {
 	u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */
 
-	select_peripheral(PIOA, pin_mask, PERIPH_A, 0);
+	select_peripheral(PIOA, pin_mask, PERIPH_A, AT32_GPIOF_PULLUP);
 }
 
 static inline void configure_usart2_pins(void)
 {
 	u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */
 
-	select_peripheral(PIOB, pin_mask, PERIPH_B, 0);
+	select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
 }
 
 static inline void configure_usart3_pins(void)
 {
 	u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */
 
-	select_peripheral(PIOB, pin_mask, PERIPH_B, 0);
+	select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
 }
 
 static struct platform_device *__initdata at32_usarts[4];

arch/ia64/hp/sim/Kconfig

@@ -4,6 +4,7 @@ menu "HP Simulator drivers"
 
 config HP_SIMETH
 	bool "Simulated Ethernet "
+	depends on NET
 
 config HP_SIMSERIAL
 	bool "Simulated serial driver support"

arch/mips/Kconfig.debug

@@ -48,7 +48,7 @@ config RUNTIME_DEBUG
 	help
 	  If you say Y here, some debugging macros will do run-time checking.
 	  If you say N here, those macros will mostly turn to no-ops.  See
-	  include/asm-mips/debug.h for debuging macros.
+	  arch/mips/include/asm/debug.h for debugging macros.
 	  If unsure, say N.
 
 endmenu

arch/mips/include/asm/asmmacro.h

@@ -35,6 +35,16 @@
 	mtc0	\reg, CP0_TCSTATUS
 	_ehb
 	.endm
+#elif defined(CONFIG_CPU_MIPSR2)
+	.macro	local_irq_enable reg=t0
+	ei
+	irq_enable_hazard
+	.endm
+
+	.macro	local_irq_disable reg=t0
+	di
+	irq_disable_hazard
+	.endm
 #else
 	.macro	local_irq_enable reg=t0
 	mfc0	\reg, CP0_STATUS

arch/mips/include/asm/byteorder.h

@@ -50,9 +50,8 @@ static inline __attribute_const__ __u32 __arch_swab32(__u32 x)
 static inline __attribute_const__ __u64 __arch_swab64(__u64 x)
 {
 	__asm__(
-	"	dsbh	%0, %1			\n"
-	"	dshd	%0, %0			\n"
-	"	drotr	%0, %0, 32		\n"
+	"	dsbh	%0, %1\n"
+	"	dshd	%0, %0"
 	: "=r" (x)
 	: "r" (x));
 

arch/mips/include/asm/elf.h

@@ -232,7 +232,7 @@ typedef elf_fpreg_t elf_fpregset_t[ELF_NFPREG];
  */
 #ifdef __MIPSEB__
 #define ELF_DATA	ELFDATA2MSB
-#elif __MIPSEL__
+#elif defined(__MIPSEL__)
 #define ELF_DATA	ELFDATA2LSB
 #endif
 #define ELF_ARCH	EM_MIPS

arch/mips/mm/dma-default.c

@@ -111,6 +111,7 @@ EXPORT_SYMBOL(dma_alloc_coherent);
 void dma_free_noncoherent(struct device *dev, size_t size, void *vaddr,
 	dma_addr_t dma_handle)
 {
+	plat_unmap_dma_mem(dma_handle);
 	free_pages((unsigned long) vaddr, get_order(size));
 }
 
@@ -121,6 +122,8 @@ void dma_free_coherent(struct device *dev, size_t size, void *vaddr,
 {
 	unsigned long addr = (unsigned long) vaddr;
 
+	plat_unmap_dma_mem(dma_handle);
+
 	if (!plat_device_is_coherent(dev))
 		addr = CAC_ADDR(addr);
 

arch/parisc/include/asm/tlbflush.h

@@ -44,9 +44,12 @@ static inline void flush_tlb_mm(struct mm_struct *mm)
 {
 	BUG_ON(mm == &init_mm); /* Should never happen */
 
-#ifdef CONFIG_SMP
+#if 1 || defined(CONFIG_SMP)
 	flush_tlb_all();
 #else
+	/* FIXME: currently broken, causing space id and protection ids
+	 *  to go out of sync, resulting in faults on userspace accesses.
+	 */
 	if (mm) {
 		if (mm->context != 0)
 			free_sid(mm->context);

arch/powerpc/boot/Makefile

@@ -41,6 +41,7 @@ $(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
 $(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405
 $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
+$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
 $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
 $(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405
 

arch/powerpc/kernel/misc_32.S

@@ -479,17 +479,20 @@ _GLOBAL(_tlbil_pid)
  * (no broadcast)
  */
 _GLOBAL(_tlbil_va)
+	mfmsr	r10
+	wrteei	0
 	slwi	r4,r4,16
 	mtspr	SPRN_MAS6,r4		/* assume AS=0 for now */
 	tlbsx	0,r3
 	mfspr	r4,SPRN_MAS1		/* check valid */
 	andis.	r3,r4,MAS1_VALID@h
-	beqlr
+	beq	1f
 	rlwinm	r4,r4,0,1,31
 	mtspr	SPRN_MAS1,r4
 	tlbwe
 	msync
 	isync
+1:	wrtee	r10
 	blr
 #endif /* CONFIG_FSL_BOOKE */
 

arch/powerpc/lib/rheap.c

@@ -556,6 +556,7 @@ unsigned long rh_alloc_fixed(rh_info_t * info, unsigned long start, int size, co
 		be = blk->start + blk->size;
 		if (s >= bs && e <= be)
 			break;
+		blk = NULL;
 	}
 
 	if (blk == NULL)

arch/powerpc/mm/hugetlbpage.c

@@ -507,6 +507,9 @@ unsigned long hugetlb_get_unmapped_area(struct file *file, unsigned long addr,
 {
 	struct hstate *hstate = hstate_file(file);
 	int mmu_psize = shift_to_mmu_psize(huge_page_shift(hstate));
+
+	if (!mmu_huge_psizes[mmu_psize])
+		return -EINVAL;
 	return slice_get_unmapped_area(addr, len, flags, mmu_psize, 1, 0);
 }
 

arch/powerpc/mm/numa.c

@@ -901,10 +901,17 @@ static void mark_reserved_regions_for_nid(int nid)
 			if (end_pfn > node_ar.end_pfn)
 				reserve_size = (node_ar.end_pfn << PAGE_SHIFT)
 					- (start_pfn << PAGE_SHIFT);
-			dbg("reserve_bootmem %lx %lx nid=%d\n", physbase,
-				reserve_size, node_ar.nid);
-			reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase,
-						reserve_size, BOOTMEM_DEFAULT);
+			/*
+			 * Only worry about *this* node, others may not
+			 * yet have valid NODE_DATA().
+			 */
+			if (node_ar.nid == nid) {
+				dbg("reserve_bootmem %lx %lx nid=%d\n",
+					physbase, reserve_size, node_ar.nid);
+				reserve_bootmem_node(NODE_DATA(node_ar.nid),
+						physbase, reserve_size,
+						BOOTMEM_DEFAULT);
+			}
 			/*
 			 * if reserved region is contained in the active region
 			 * then done.
@@ -929,7 +936,6 @@ static void mark_reserved_regions_for_nid(int nid)
 void __init do_init_bootmem(void)
 {
 	int nid;
-	unsigned int i;
 
 	min_low_pfn = 0;
 	max_low_pfn = lmb_end_of_DRAM() >> PAGE_SHIFT;

arch/powerpc/platforms/cell/axon_msi.c

@@ -413,6 +413,9 @@ static int axon_msi_probe(struct of_device *device,
 			MSIC_CTRL_IRQ_ENABLE | MSIC_CTRL_ENABLE |
 			MSIC_CTRL_FIFO_SIZE);
 
+	msic->read_offset = dcr_read(msic->dcr_host, MSIC_WRITE_OFFSET_REG)
+				& MSIC_FIFO_SIZE_MASK;
+
 	device->dev.platform_data = msic;
 
 	ppc_md.setup_msi_irqs = axon_msi_setup_msi_irqs;

arch/sh/Kconfig

@@ -55,6 +55,8 @@ config GENERIC_HARDIRQS
 
 config GENERIC_HARDIRQS_NO__DO_IRQ
 	def_bool y
+	depends on SUPERH32 && (!SH_DREAMCAST && !SH_SH4202_MICRODEV && \
+				!SH_7751_SYSTEMH && !HD64461)
 
 config GENERIC_IRQ_PROBE
 	def_bool y

arch/sparc/include/asm/ptrace_32.h

@@ -62,6 +62,8 @@ struct sparc_stackf {
 
 #ifdef __KERNEL__
 
+#include <asm/system.h>
+
 static inline bool pt_regs_is_syscall(struct pt_regs *regs)
 {
 	return (regs->psr & PSR_SYSCALL);
@@ -72,6 +74,14 @@ static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
 	return (regs->psr &= ~PSR_SYSCALL);
 }
 
+#define arch_ptrace_stop_needed(exit_code, info) \
+({	flush_user_windows(); \
+	current_thread_info()->w_saved != 0;	\
+})
+
+#define arch_ptrace_stop(exit_code, info) \
+	synchronize_user_stack()
+
 #define user_mode(regs) (!((regs)->psr & PSR_PS))
 #define instruction_pointer(regs) ((regs)->pc)
 #define user_stack_pointer(regs) ((regs)->u_regs[UREG_FP])

arch/sparc/include/asm/ptrace_64.h

@@ -114,6 +114,7 @@ struct sparc_trapf {
 #ifdef __KERNEL__
 
 #include <linux/threads.h>
+#include <asm/system.h>
 
 static inline int pt_regs_trap_type(struct pt_regs *regs)
 {
@@ -130,6 +131,14 @@ static inline bool pt_regs_clear_syscall(struct pt_regs *regs)
 	return (regs->tstate &= ~TSTATE_SYSCALL);
 }
 
+#define arch_ptrace_stop_needed(exit_code, info) \
+({	flush_user_windows(); \
+	get_thread_wsaved() != 0; \
+})
+
+#define arch_ptrace_stop(exit_code, info) \
+	synchronize_user_stack()
+
 struct global_reg_snapshot {
 	unsigned long		tstate;
 	unsigned long		tpc;

arch/x86/Kconfig.cpu

@@ -520,6 +520,7 @@ config X86_PTRACE_BTS
 	bool "Branch Trace Store"
 	default y
 	depends on X86_DEBUGCTLMSR
+	depends on BROKEN
 	help
 	  This adds a ptrace interface to the hardware's branch trace store.
 

arch/x86/include/asm/vmi.h

@@ -223,9 +223,15 @@ struct pci_header {
 } __attribute__((packed));
 
 /* Function prototypes for bootstrapping */
+#ifdef CONFIG_VMI
 extern void vmi_init(void);
+extern void vmi_activate(void);
 extern void vmi_bringup(void);
-extern void vmi_apply_boot_page_allocations(void);
+#else
+static inline void vmi_init(void) {}
+static inline void vmi_activate(void) {}
+static inline void vmi_bringup(void) {}
+#endif
 
 /* State needed to start an application processor in an SMP system. */
 struct vmi_ap_state {

arch/x86/kernel/amd_iommu.c

@@ -235,8 +235,9 @@ static int iommu_completion_wait(struct amd_iommu *iommu)
 	status &= ~MMIO_STATUS_COM_WAIT_INT_MASK;
 	writel(status, iommu->mmio_base + MMIO_STATUS_OFFSET);
 
-	if (unlikely((i == EXIT_LOOP_COUNT) && printk_ratelimit()))
-		printk(KERN_WARNING "AMD IOMMU: Completion wait loop failed\n");
+	if (unlikely(i == EXIT_LOOP_COUNT))
+		panic("AMD IOMMU: Completion wait loop failed\n");
+
 out:
 	spin_unlock_irqrestore(&iommu->lock, flags);
 

arch/x86/kernel/amd_iommu_init.c

@@ -427,6 +427,10 @@ static u8 * __init alloc_command_buffer(struct amd_iommu *iommu)
 	memcpy_toio(iommu->mmio_base + MMIO_CMD_BUF_OFFSET,
 			&entry, sizeof(entry));
 
+	/* set head and tail to zero manually */
+	writel(0x00, iommu->mmio_base + MMIO_CMD_HEAD_OFFSET);
+	writel(0x00, iommu->mmio_base + MMIO_CMD_TAIL_OFFSET);
+
 	iommu_feature_enable(iommu, CONTROL_CMDBUF_EN);
 
 	return cmd_buf;
@@ -1074,7 +1078,8 @@ int __init amd_iommu_init(void)
 		goto free;
 
 	/* IOMMU rlookup table - find the IOMMU for a specific device */
-	amd_iommu_rlookup_table = (void *)__get_free_pages(GFP_KERNEL,
+	amd_iommu_rlookup_table = (void *)__get_free_pages(
+			GFP_KERNEL | __GFP_ZERO,
 			get_order(rlookup_table_size));
 	if (amd_iommu_rlookup_table == NULL)
 		goto free;

arch/x86/kernel/cpu/mcheck/mce_64.c

@@ -510,12 +510,9 @@ static void __cpuinit mce_cpu_features(struct cpuinfo_x86 *c)
  */
 void __cpuinit mcheck_init(struct cpuinfo_x86 *c)
 {
-	static cpumask_t mce_cpus = CPU_MASK_NONE;
-
 	mce_cpu_quirks(c);
 
 	if (mce_dont_init ||
-	    cpu_test_and_set(smp_processor_id(), mce_cpus) ||
 	    !mce_available(c))
 		return;
 

arch/x86/kernel/microcode_core.c

@@ -272,13 +272,18 @@ static struct attribute_group mc_attr_group = {
 	.name = "microcode",
 };
 
-static void microcode_fini_cpu(int cpu)
+static void __microcode_fini_cpu(int cpu)
 {
 	struct ucode_cpu_info *uci = ucode_cpu_info + cpu;
 
-	mutex_lock(&microcode_mutex);
 	microcode_ops->microcode_fini_cpu(cpu);
 	uci->valid = 0;
+}
+
+static void microcode_fini_cpu(int cpu)
+{
+	mutex_lock(&microcode_mutex);
+	__microcode_fini_cpu(cpu);
 	mutex_unlock(&microcode_mutex);
 }
 
@@ -306,12 +311,16 @@ static int microcode_resume_cpu(int cpu)
 	 * to this cpu (a bit of paranoia):
 	 */
 	if (microcode_ops->collect_cpu_info(cpu, &nsig)) {
-		microcode_fini_cpu(cpu);
+		__microcode_fini_cpu(cpu);
+		printk(KERN_ERR "failed to collect_cpu_info for resuming cpu #%d\n",
+				cpu);
 		return -1;
 	}
 
-	if (memcmp(&nsig, &uci->cpu_sig, sizeof(nsig))) {
-		microcode_fini_cpu(cpu);
+	if ((nsig.sig != uci->cpu_sig.sig) || (nsig.pf != uci->cpu_sig.pf)) {
+		__microcode_fini_cpu(cpu);
+		printk(KERN_ERR "cached ucode doesn't match the resuming cpu #%d\n",
+				cpu);
 		/* Should we look for a new ucode here? */
 		return 1;
 	}

arch/x86/kernel/microcode_intel.c

@@ -155,6 +155,7 @@ static DEFINE_SPINLOCK(microcode_update_lock);
 static int collect_cpu_info(int cpu_num, struct cpu_signature *csig)
 {
 	struct cpuinfo_x86 *c = &cpu_data(cpu_num);
+	unsigned long flags;
 	unsigned int val[2];
 
 	memset(csig, 0, sizeof(*csig));
@@ -174,11 +175,16 @@ static int collect_cpu_info(int cpu_num, struct cpu_signature *csig)
 		csig->pf = 1 << ((val[1] >> 18) & 7);
 	}
 
+	/* serialize access to the physical write to MSR 0x79 */
+	spin_lock_irqsave(&microcode_update_lock, flags);
+
 	wrmsr(MSR_IA32_UCODE_REV, 0, 0);
 	/* see notes above for revision 1.07.  Apparent chip bug */
 	sync_core();
 	/* get the current revision from MSR 0x8B */
 	rdmsr(MSR_IA32_UCODE_REV, val[0], csig->rev);
+	spin_unlock_irqrestore(&microcode_update_lock, flags);
+
 	pr_debug("microcode: collect_cpu_info : sig=0x%x, pf=0x%x, rev=0x%x\n",
 			csig->sig, csig->pf, csig->rev);
 

arch/x86/kernel/pci-gart_64.c

@@ -745,10 +745,8 @@ void __init gart_iommu_init(void)
 	unsigned long scratch;
 	long i;
 
-	if (cache_k8_northbridges() < 0 || num_k8_northbridges == 0) {
-		printk(KERN_INFO "PCI-GART: No AMD GART found.\n");
+	if (cache_k8_northbridges() < 0 || num_k8_northbridges == 0)
 		return;
-	}
 
 #ifndef CONFIG_AGP_AMD64
 	no_agp = 1;

arch/x86/kernel/setup.c

@@ -794,6 +794,9 @@ void __init setup_arch(char **cmdline_p)
 	printk(KERN_INFO "Command line: %s\n", boot_command_line);
 #endif
 
+	/* VMI may relocate the fixmap; do this before touching ioremap area */
+	vmi_init();
+
 	early_cpu_init();
 	early_ioremap_init();
 
@@ -880,13 +883,8 @@ void __init setup_arch(char **cmdline_p)
 	check_efer();
 #endif
 
-#if defined(CONFIG_VMI) && defined(CONFIG_X86_32)
-	/*
-	 * Must be before kernel pagetables are setup
-	 * or fixmap area is touched.
-	 */
-	vmi_init();
-#endif
+	/* Must be before kernel pagetables are setup */
+	vmi_activate();
 
 	/* after early param, so could get panic from serial */
 	reserve_early_setup_data();

arch/x86/kernel/smpboot.c

@@ -294,9 +294,7 @@ static void __cpuinit start_secondary(void *unused)
 	 * fragile that we want to limit the things done here to the
 	 * most necessary things.
 	 */
-#ifdef CONFIG_VMI
 	vmi_bringup();
-#endif
 	cpu_init();
 	preempt_disable();
 	smp_callin();

arch/x86/kernel/vmi_32.c

@@ -960,8 +960,6 @@ static inline int __init activate_vmi(void)
 
 void __init vmi_init(void)
 {
-	unsigned long flags;
-
 	if (!vmi_rom)
 		probe_vmi_rom();
 	else
@@ -973,13 +971,21 @@ void __init vmi_init(void)
 
 	reserve_top_address(-vmi_rom->virtual_top);
 
-	local_irq_save(flags);
-	activate_vmi();
-
 #ifdef CONFIG_X86_IO_APIC
 	/* This is virtual hardware; timer routing is wired correctly */
 	no_timer_check = 1;
 #endif
+}
+
+void vmi_activate(void)
+{
+	unsigned long flags;
+
+	if (!vmi_rom)
+		return;
+
+	local_irq_save(flags);
+	activate_vmi();
 	local_irq_restore(flags & X86_EFLAGS_IF);
 }
 

crypto/async_tx/async_xor.c

@@ -53,10 +53,17 @@ do_async_xor(struct dma_chan *chan, struct page *dest, struct page **src_list,
 	int xor_src_cnt;
 	dma_addr_t dma_dest;
 
-	dma_dest = dma_map_page(dma->dev, dest, offset, len, DMA_FROM_DEVICE);
-	for (i = 0; i < src_cnt; i++)
+	/* map the dest bidrectional in case it is re-used as a source */
+	dma_dest = dma_map_page(dma->dev, dest, offset, len, DMA_BIDIRECTIONAL);
+	for (i = 0; i < src_cnt; i++) {
+		/* only map the dest once */
+		if (unlikely(src_list[i] == dest)) {
+			dma_src[i] = dma_dest;
+			continue;
+		}
 		dma_src[i] = dma_map_page(dma->dev, src_list[i], offset,
 					  len, DMA_TO_DEVICE);
+	}
 
 	while (src_cnt) {
 		async_flags = flags;

drivers/acpi/bus.c

@@ -688,14 +688,6 @@ void __init acpi_early_init(void)
 	if (acpi_disabled)
 		return;
 
-	/*
-	 * ACPI CA initializes acpi_dbg_level to non-zero, which means
-	 * we get debug output merely by turning on CONFIG_ACPI_DEBUG.
-	 * Turn it off so we don't get output unless the user specifies
-	 * acpi.debug_level.
-	 */
-	acpi_dbg_level = 0;
-
 	printk(KERN_INFO PREFIX "Core revision %08x\n", ACPI_CA_VERSION);
 
 	/* enable workarounds, unless strict ACPI spec. compliance */

drivers/acpi/toshiba_acpi.c

@@ -824,32 +824,36 @@ static int __init toshiba_acpi_init(void)
 			toshiba_acpi_exit();
 			return -ENOMEM;
 		}
-	}
 
-	/* Register input device for kill switch */
-	toshiba_acpi.poll_dev = input_allocate_polled_device();
-	if (!toshiba_acpi.poll_dev) {
-		printk(MY_ERR "unable to allocate kill-switch input device\n");
-		toshiba_acpi_exit();
-		return -ENOMEM;
-	}
-	toshiba_acpi.poll_dev->private = &toshiba_acpi;
-	toshiba_acpi.poll_dev->poll = bt_poll_rfkill;
-	toshiba_acpi.poll_dev->poll_interval = 1000; /* msecs */
-
-	toshiba_acpi.poll_dev->input->name = toshiba_acpi.rfk_name;
-	toshiba_acpi.poll_dev->input->id.bustype = BUS_HOST;
-	toshiba_acpi.poll_dev->input->id.vendor = 0x0930; /* Toshiba USB ID */
-	set_bit(EV_SW, toshiba_acpi.poll_dev->input->evbit);
-	set_bit(SW_RFKILL_ALL, toshiba_acpi.poll_dev->input->swbit);
-	input_report_switch(toshiba_acpi.poll_dev->input, SW_RFKILL_ALL, TRUE);
-	input_sync(toshiba_acpi.poll_dev->input);
-
-	ret = input_register_polled_device(toshiba_acpi.poll_dev);
-	if (ret) {
-		printk(MY_ERR "unable to register kill-switch input device\n");
-		toshiba_acpi_exit();
-		return ret;
+		/* Register input device for kill switch */
+		toshiba_acpi.poll_dev = input_allocate_polled_device();
+		if (!toshiba_acpi.poll_dev) {
+			printk(MY_ERR
+			       "unable to allocate kill-switch input device\n");
+			toshiba_acpi_exit();
+			return -ENOMEM;
+		}
+		toshiba_acpi.poll_dev->private = &toshiba_acpi;
+		toshiba_acpi.poll_dev->poll = bt_poll_rfkill;
+		toshiba_acpi.poll_dev->poll_interval = 1000; /* msecs */
+
+		toshiba_acpi.poll_dev->input->name = toshiba_acpi.rfk_name;
+		toshiba_acpi.poll_dev->input->id.bustype = BUS_HOST;
+		/* Toshiba USB ID */
+		toshiba_acpi.poll_dev->input->id.vendor = 0x0930;
+		set_bit(EV_SW, toshiba_acpi.poll_dev->input->evbit);
+		set_bit(SW_RFKILL_ALL, toshiba_acpi.poll_dev->input->swbit);
+		input_report_switch(toshiba_acpi.poll_dev->input,
+				    SW_RFKILL_ALL, TRUE);
+		input_sync(toshiba_acpi.poll_dev->input);
+
+		ret = input_register_polled_device(toshiba_acpi.poll_dev);
+		if (ret) {
+			printk(MY_ERR
+			       "unable to register kill-switch input device\n");
+			toshiba_acpi_exit();
+			return ret;
+		}
 	}
 
 	return 0;

drivers/acpi/utilities/utglobal.c

@@ -64,7 +64,7 @@ u32 acpi_dbg_level = ACPI_DEBUG_DEFAULT;
 
 /* Debug switch - layer (component) mask */
 
-u32 acpi_dbg_layer = ACPI_COMPONENT_DEFAULT | ACPI_ALL_DRIVERS;
+u32 acpi_dbg_layer = 0;
 u32 acpi_gbl_nesting_level = 0;
 
 /* Debugger globals */

drivers/ata/libata-core.c

@@ -4050,17 +4050,70 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 	{ "ST3160023AS",	"3.42",		ATA_HORKAGE_NONCQ },
 
 	/* Seagate NCQ + FLUSH CACHE firmware bug */
-	{ "ST31500341AS",	"9JU138",	ATA_HORKAGE_NONCQ |
+	{ "ST31500341AS",	"SD15",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
-	{ "ST31000333AS",	"9FZ136",	ATA_HORKAGE_NONCQ |
+	{ "ST31500341AS",	"SD16",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
-	{ "ST3640623AS",	"9FZ164",	ATA_HORKAGE_NONCQ |
+	{ "ST31500341AS",	"SD17",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
-	{ "ST3640323AS",	"9FZ134",	ATA_HORKAGE_NONCQ |
+	{ "ST31500341AS",	"SD18",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
-	{ "ST3320813AS",	"9FZ182",	ATA_HORKAGE_NONCQ |
+	{ "ST31500341AS",	"SD19",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
-	{ "ST3320613AS",	"9FZ162",	ATA_HORKAGE_NONCQ |
+
+	{ "ST31000333AS",	"SD15",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST31000333AS",	"SD16",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST31000333AS",	"SD17",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST31000333AS",	"SD18",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST31000333AS",	"SD19",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+
+	{ "ST3640623AS",	"SD15",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640623AS",	"SD16",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640623AS",	"SD17",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640623AS",	"SD18",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640623AS",	"SD19",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+
+	{ "ST3640323AS",	"SD15",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640323AS",	"SD16",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640323AS",	"SD17",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640323AS",	"SD18",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3640323AS",	"SD19",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+
+	{ "ST3320813AS",	"SD15",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320813AS",	"SD16",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320813AS",	"SD17",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320813AS",	"SD18",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320813AS",	"SD19",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+
+	{ "ST3320613AS",	"SD15",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320613AS",	"SD16",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320613AS",	"SD17",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320613AS",	"SD18",		ATA_HORKAGE_NONCQ |
+						ATA_HORKAGE_FIRMWARE_WARN },
+	{ "ST3320613AS",	"SD19",		ATA_HORKAGE_NONCQ |
 						ATA_HORKAGE_FIRMWARE_WARN },
 
 	/* Blacklist entries taken from Silicon Image 3124/3132

drivers/ata/pata_hpt366.c

@@ -183,7 +183,9 @@ static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
 			mask &= ~(0xF8 << ATA_SHIFT_UDMA);
 		if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
 			mask &= ~(0xF0 << ATA_SHIFT_UDMA);
-	}
+	} else if (adev->class == ATA_DEV_ATAPI)
+		mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+
 	return ata_bmdma_mode_filter(adev, mask);
 }
 
@@ -211,11 +213,15 @@ static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
 
 static int hpt36x_cable_detect(struct ata_port *ap)
 {
-	u8 ata66;
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 ata66;
 
+	/*
+	 * Each channel of pata_hpt366 occupies separate PCI function
+	 * as the primary channel and bit1 indicates the cable type.
+	 */
 	pci_read_config_byte(pdev, 0x5A, &ata66);
-	if (ata66 & (1 << ap->port_no))
+	if (ata66 & 2)
 		return ATA_CBL_PATA40;
 	return ATA_CBL_PATA80;
 }

drivers/block/cciss.c

@@ -1693,6 +1693,11 @@ static int rebuild_lun_table(ctlr_info_t *h, int first_time)
 	for (i = 0; i <= h->highest_lun; i++) {
 		int j;
 		drv_found = 0;
+
+		/* skip holes in the array from already deleted drives */
+		if (h->drv[i].raid_level == -1)
+			continue;
+
 		for (j = 0; j < num_luns; j++) {
 			memcpy(&lunid, &ld_buff->LUN[j][0], 4);
 			lunid = le32_to_cpu(lunid);

drivers/cdrom/cdrom.c

@@ -2081,10 +2081,6 @@ static int cdrom_read_cdda_bpc(struct cdrom_device_info *cdi, __u8 __user *ubuf,
 	if (!q)
 		return -ENXIO;
 
-	rq = blk_get_request(q, READ, GFP_KERNEL);
-	if (!rq)
-		return -ENOMEM;
-
 	cdi->last_sense = 0;
 
 	while (nframes) {
@@ -2096,9 +2092,17 @@ static int cdrom_read_cdda_bpc(struct cdrom_device_info *cdi, __u8 __user *ubuf,
 
 		len = nr * CD_FRAMESIZE_RAW;
 
+		rq = blk_get_request(q, READ, GFP_KERNEL);
+		if (!rq) {
+			ret = -ENOMEM;
+			break;
+		}
+
 		ret = blk_rq_map_user(q, rq, NULL, ubuf, len, GFP_KERNEL);
-		if (ret)
+		if (ret) {
+			blk_put_request(rq);
 			break;
+		}
 
 		rq->cmd[0] = GPCMD_READ_CD;
 		rq->cmd[1] = 1 << 2;
@@ -2124,6 +2128,7 @@ static int cdrom_read_cdda_bpc(struct cdrom_device_info *cdi, __u8 __user *ubuf,
 
 		if (blk_rq_unmap_user(bio))
 			ret = -EFAULT;
+		blk_put_request(rq);
 
 		if (ret)
 			break;
@@ -2133,7 +2138,6 @@ static int cdrom_read_cdda_bpc(struct cdrom_device_info *cdi, __u8 __user *ubuf,
 		ubuf += len;
 	}
 
-	blk_put_request(rq);
 	return ret;
 }
 

drivers/char/cp437.uni

@@ -27,7 +27,7 @@
 0x0c	U+2640
 0x0d	U+266a
 0x0e	U+266b
-0x0f	U+263c
+0x0f	U+263c U+00a4
 0x10	U+25b6 U+25ba
 0x11	U+25c0 U+25c4
 0x12	U+2195
@@ -55,7 +55,7 @@
 0x24	U+0024
 0x25	U+0025
 0x26	U+0026
-0x27	U+0027
+0x27	U+0027 U+00b4
 0x28	U+0028
 0x29	U+0029
 0x2a	U+002a
@@ -84,7 +84,7 @@
 0x41	U+0041 U+00c0 U+00c1 U+00c2 U+00c3
 0x42	U+0042
 0x43	U+0043 U+00a9
-0x44	U+0044
+0x44	U+0044 U+00d0
 0x45	U+0045 U+00c8 U+00ca U+00cb
 0x46	U+0046
 0x47	U+0047
@@ -140,7 +140,7 @@
 0x79	U+0079 U+00fd
 0x7a	U+007a
 0x7b	U+007b
-0x7c	U+007c U+00a5
+0x7c	U+007c U+00a6
 0x7d	U+007d
 0x7e	U+007e
 #
@@ -263,10 +263,10 @@
 0xe8	U+03a6 U+00d8
 0xe9	U+0398
 0xea	U+03a9 U+2126
-0xeb	U+03b4
+0xeb	U+03b4 U+00f0
 0xec	U+221e
 0xed	U+03c6 U+00f8
-0xee	U+03b5
+0xee	U+03b5 U+2208
 0xef	U+2229
 0xf0	U+2261
 0xf1	U+00b1

drivers/char/vt.c

@@ -2274,7 +2274,7 @@ rescan_last_byte:
 				    continue; /* nothing to display */
 				}
 				/* Glyph not found */
-				if ((!(vc->vc_utf && !vc->vc_disp_ctrl) || c < 128) && !(c & ~charmask)) {
+				if ((!(vc->vc_utf && !vc->vc_disp_ctrl) && c < 128) && !(c & ~charmask)) {
 				    /* In legacy mode use the glyph we get by a 1:1 mapping.
 				       This would make absolutely no sense with Unicode in mind,
 				       but do this for ASCII characters since a font may lack

drivers/char/xilinx_hwicap/buffer_icap.c

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2003-2008 Xilinx Inc.
  *     All rights reserved.
  *

drivers/char/xilinx_hwicap/buffer_icap.h

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2003-2008 Xilinx Inc.
  *     All rights reserved.
  *

drivers/char/xilinx_hwicap/fifo_icap.c

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2007-2008 Xilinx Inc.
  *     All rights reserved.
  *

drivers/char/xilinx_hwicap/fifo_icap.h

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2007-2008 Xilinx Inc.
  *     All rights reserved.
  *

drivers/char/xilinx_hwicap/xilinx_hwicap.c

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2002 Xilinx Inc., Systems Engineering Group
  *     (c) Copyright 2004 Xilinx Inc., Systems Engineering Group
  *     (c) Copyright 2007-2008 Xilinx Inc.

drivers/char/xilinx_hwicap/xilinx_hwicap.h

@@ -21,9 +21,6 @@
  *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  *     FOR A PARTICULAR PURPOSE.
  *
- *     Xilinx products are not intended for use in life support appliances,
- *     devices, or systems. Use in such applications is expressly prohibited.
- *
  *     (c) Copyright 2003-2007 Xilinx Inc.
  *     All rights reserved.
  *

drivers/dma/dmaengine.c

@@ -388,7 +388,10 @@ int dma_async_device_register(struct dma_device *device)
 
 	init_completion(&device->done);
 	kref_init(&device->refcount);
+
+	mutex_lock(&dma_list_mutex);
 	device->dev_id = id++;
+	mutex_unlock(&dma_list_mutex);
 
 	/* represent channels in sysfs. Probably want devs too */
 	list_for_each_entry(chan, &device->channels, device_node) {

drivers/dma/ioat_dma.c

@@ -1341,10 +1341,12 @@ static void ioat_dma_start_null_desc(struct ioat_dma_chan *ioat_chan)
  */
 #define IOAT_TEST_SIZE 2000
 
+DECLARE_COMPLETION(test_completion);
 static void ioat_dma_test_callback(void *dma_async_param)
 {
 	printk(KERN_ERR "ioatdma: ioat_dma_test_callback(%p)\n",
 		dma_async_param);
+	complete(&test_completion);
 }
 
 /**
@@ -1410,7 +1412,8 @@ static int ioat_dma_self_test(struct ioatdma_device *device)
 		goto free_resources;
 	}
 	device->common.device_issue_pending(dma_chan);
-	msleep(1);
+
+	wait_for_completion_timeout(&test_completion, msecs_to_jiffies(3000));
 
 	if (device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
 					!= DMA_SUCCESS) {

drivers/dma/iop-adma.c

@@ -85,18 +85,28 @@ iop_adma_run_tx_complete_actions(struct iop_adma_desc_slot *desc,
 			enum dma_ctrl_flags flags = desc->async_tx.flags;
 			u32 src_cnt;
 			dma_addr_t addr;
+			dma_addr_t dest;
 
+			src_cnt = unmap->unmap_src_cnt;
+			dest = iop_desc_get_dest_addr(unmap, iop_chan);
 			if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
-				addr = iop_desc_get_dest_addr(unmap, iop_chan);
-				dma_unmap_page(dev, addr, len, DMA_FROM_DEVICE);
+				enum dma_data_direction dir;
+
+				if (src_cnt > 1) /* is xor? */
+					dir = DMA_BIDIRECTIONAL;
+				else
+					dir = DMA_FROM_DEVICE;
+
+				dma_unmap_page(dev, dest, len, dir);
 			}
 
 			if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
-				src_cnt = unmap->unmap_src_cnt;
 				while (src_cnt--) {
 					addr = iop_desc_get_src_addr(unmap,
 								     iop_chan,
 								     src_cnt);
+					if (addr == dest)
+						continue;
 					dma_unmap_page(dev, addr, len,
 						       DMA_TO_DEVICE);
 				}

drivers/dma/mv_xor.c

@@ -311,17 +311,26 @@ mv_xor_run_tx_complete_actions(struct mv_xor_desc_slot *desc,
 			enum dma_ctrl_flags flags = desc->async_tx.flags;
 			u32 src_cnt;
 			dma_addr_t addr;
+			dma_addr_t dest;
 
+			src_cnt = unmap->unmap_src_cnt;
+			dest = mv_desc_get_dest_addr(unmap);
 			if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
-				addr = mv_desc_get_dest_addr(unmap);
-				dma_unmap_page(dev, addr, len, DMA_FROM_DEVICE);
+				enum dma_data_direction dir;
+
+				if (src_cnt > 1) /* is xor ? */
+					dir = DMA_BIDIRECTIONAL;
+				else
+					dir = DMA_FROM_DEVICE;
+				dma_unmap_page(dev, dest, len, dir);
 			}
 
 			if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
-				src_cnt = unmap->unmap_src_cnt;
 				while (src_cnt--) {
 					addr = mv_desc_get_src_addr(unmap,
 								    src_cnt);
+					if (addr == dest)
+						continue;
 					dma_unmap_page(dev, addr, len,
 						       DMA_TO_DEVICE);
 				}

drivers/edac/edac_device.c

@@ -394,6 +394,12 @@ static void edac_device_workq_function(struct work_struct *work_req)
 
 	mutex_lock(&device_ctls_mutex);
 
+	/* If we are being removed, bail out immediately */
+	if (edac_dev->op_state == OP_OFFLINE) {
+		mutex_unlock(&device_ctls_mutex);
+		return;
+	}
+
 	/* Only poll controllers that are running polled and have a check */
 	if ((edac_dev->op_state == OP_RUNNING_POLL) &&
 		(edac_dev->edac_check != NULL)) {
@@ -585,14 +591,14 @@ struct edac_device_ctl_info *edac_device_del_device(struct device *dev)
 	/* mark this instance as OFFLINE */
 	edac_dev->op_state = OP_OFFLINE;
 
-	/* clear workq processing on this instance */
-	edac_device_workq_teardown(edac_dev);
-
 	/* deregister from global list */
 	del_edac_device_from_global_list(edac_dev);
 
 	mutex_unlock(&device_ctls_mutex);
 
+	/* clear workq processing on this instance */
+	edac_device_workq_teardown(edac_dev);
+
 	/* Tear down the sysfs entries for this instance */
 	edac_device_remove_sysfs(edac_dev);
 

drivers/gpu/drm/i915/i915_dma.c

@@ -717,7 +717,7 @@ static int i915_getparam(struct drm_device *dev, void *data,
 		value = dev->pci_device;
 		break;
 	case I915_PARAM_HAS_GEM:
-		value = 1;
+		value = dev_priv->has_gem;
 		break;
 	default:
 		DRM_ERROR("Unknown parameter %d\n", param->param);
@@ -830,6 +830,14 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 
 	dev_priv->regs = ioremap(base, size);
 
+#ifdef CONFIG_HIGHMEM64G
+	/* don't enable GEM on PAE - needs agp + set_memory_* interface fixes */
+	dev_priv->has_gem = 0;
+#else
+	/* enable GEM by default */
+	dev_priv->has_gem = 1;
+#endif
+
 	i915_gem_load(dev);
 
 	/* Init HWS */

drivers/gpu/drm/i915/i915_drv.h

@@ -106,6 +106,8 @@ struct intel_opregion {
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
+	int has_gem;
+
 	void __iomem *regs;
 	drm_local_map_t *sarea;
 

drivers/gpu/drm/i915/i915_gem.c

@@ -2309,7 +2309,14 @@ i915_gem_busy_ioctl(struct drm_device *dev, void *data,
 	}
 
 	obj_priv = obj->driver_private;
-	args->busy = obj_priv->active;
+	/* Don't count being on the flushing list against the object being
+	 * done.  Otherwise, a buffer left on the flushing list but not getting
+	 * flushed (because nobody's flushing that domain) won't ever return
+	 * unbusy and get reused by libdrm's bo cache.  The other expected
+	 * consumer of this interface, OpenGL's occlusion queries, also specs
+	 * that the objects get unbusy "eventually" without any interference.
+	 */
+	args->busy = obj_priv->active && obj_priv->last_rendering_seqno != 0;
 
 	drm_gem_object_unreference(obj);
 	mutex_unlock(&dev->struct_mutex);

drivers/gpu/drm/radeon/radeon_irq.c

@@ -44,7 +44,7 @@ void radeon_irq_set_state(struct drm_device *dev, u32 mask, int state)
 	else
 		dev_priv->irq_enable_reg &= ~mask;
 
-	if (!dev->irq_enabled)
+	if (dev->irq_enabled)
 		RADEON_WRITE(RADEON_GEN_INT_CNTL, dev_priv->irq_enable_reg);
 }
 
@@ -57,7 +57,7 @@ static void r500_vbl_irq_set_state(struct drm_device *dev, u32 mask, int state)
 	else
 		dev_priv->r500_disp_irq_reg &= ~mask;
 
-	if (!dev->irq_enabled)
+	if (dev->irq_enabled)
 		RADEON_WRITE(R500_DxMODE_INT_MASK, dev_priv->r500_disp_irq_reg);
 }
 

drivers/i2c/busses/i2c-cpm.c

@@ -365,6 +365,7 @@ static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
 		pmsg = &msgs[tptr];
 		if (pmsg->flags & I2C_M_RD)
 			ret = wait_event_interruptible_timeout(cpm->i2c_wait,
+				(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_NAK) ||
 				!(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY),
 				1 * HZ);
 		else

drivers/i2c/busses/i2c-highlander.c

@@ -92,7 +92,7 @@ static void highlander_i2c_setup(struct highlander_i2c_dev *dev)
 static void smbus_write_data(u8 *src, u16 *dst, int len)
 {
 	for (; len > 1; len -= 2) {
-		*dst++ = be16_to_cpup((u16 *)src);
+		*dst++ = be16_to_cpup((__be16 *)src);
 		src += 2;
 	}
 
@@ -103,7 +103,7 @@ static void smbus_write_data(u8 *src, u16 *dst, int len)
 static void smbus_read_data(u16 *src, u8 *dst, int len)
 {
 	for (; len > 1; len -= 2) {
-		*(u16 *)dst = cpu_to_be16p(src++);
+		*(__be16 *)dst = cpu_to_be16p(src++);
 		dst += 2;
 	}
 

drivers/i2c/busses/i2c-pmcmsp.c

@@ -486,7 +486,7 @@ static enum pmcmsptwi_xfer_result pmcmsptwi_xfer_cmd(
 
 	if (cmd->type == MSP_TWI_CMD_WRITE ||
 	    cmd->type == MSP_TWI_CMD_WRITE_READ) {
-		__be64 tmp = cpu_to_be64p((u64 *)cmd->write_data);
+		u64 tmp = be64_to_cpup((__be64 *)cmd->write_data);
 		tmp >>= (MSP_MAX_BYTES_PER_RW - cmd->write_len) * 8;
 		dev_dbg(&pmcmsptwi_adapter.dev, "Writing 0x%016llx\n", tmp);
 		pmcmsptwi_writel(tmp & 0x00000000ffffffffLL,

drivers/i2c/busses/i2c-s3c2410.c

@@ -56,6 +56,7 @@ enum s3c24xx_i2c_state {
 struct s3c24xx_i2c {
 	spinlock_t		lock;
 	wait_queue_head_t	wait;
+	unsigned int		suspended:1;
 
 	struct i2c_msg		*msg;
 	unsigned int		msg_num;
@@ -507,7 +508,7 @@ static int s3c24xx_i2c_doxfer(struct s3c24xx_i2c *i2c, struct i2c_msg *msgs, int
 	unsigned long timeout;
 	int ret;
 
-	if (!(readl(i2c->regs + S3C2410_IICCON) & S3C2410_IICCON_IRQEN))
+	if (i2c->suspended)
 		return -EIO;
 
 	ret = s3c24xx_i2c_set_master(i2c);
@@ -986,17 +987,26 @@ static int s3c24xx_i2c_remove(struct platform_device *pdev)
 }
 
 #ifdef CONFIG_PM
+static int s3c24xx_i2c_suspend_late(struct platform_device *dev,
+				    pm_message_t msg)
+{
+	struct s3c24xx_i2c *i2c = platform_get_drvdata(dev);
+	i2c->suspended = 1;
+	return 0;
+}
+
 static int s3c24xx_i2c_resume(struct platform_device *dev)
 {
 	struct s3c24xx_i2c *i2c = platform_get_drvdata(dev);
 
-	if (i2c != NULL)
-		s3c24xx_i2c_init(i2c);
+	i2c->suspended = 0;
+	s3c24xx_i2c_init(i2c);
 
 	return 0;
 }
 
 #else
+#define s3c24xx_i2c_suspend_late NULL
 #define s3c24xx_i2c_resume NULL
 #endif
 
@@ -1005,6 +1015,7 @@ static int s3c24xx_i2c_resume(struct platform_device *dev)
 static struct platform_driver s3c2410_i2c_driver = {
 	.probe		= s3c24xx_i2c_probe,
 	.remove		= s3c24xx_i2c_remove,
+	.suspend_late	= s3c24xx_i2c_suspend_late,
 	.resume		= s3c24xx_i2c_resume,
 	.driver		= {
 		.owner	= THIS_MODULE,
@@ -1015,6 +1026,7 @@ static struct platform_driver s3c2410_i2c_driver = {
 static struct platform_driver s3c2440_i2c_driver = {
 	.probe		= s3c24xx_i2c_probe,
 	.remove		= s3c24xx_i2c_remove,
+	.suspend_late	= s3c24xx_i2c_suspend_late,
 	.resume		= s3c24xx_i2c_resume,
 	.driver		= {
 		.owner	= THIS_MODULE,

drivers/ide/cs5530.c

@@ -81,11 +81,12 @@ static u8 cs5530_udma_filter(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = drive->hwif;
 	ide_drive_t *mate = ide_get_pair_dev(drive);
-	u16 *mateid = mate->id;
+	u16 *mateid;
 	u8 mask = hwif->ultra_mask;
 
 	if (mate == NULL)
 		goto out;
+	mateid = mate->id;
 
 	if (ata_id_has_dma(mateid) && __ide_dma_bad_drive(mate) == 0) {
 		if ((mateid[ATA_ID_FIELD_VALID] & 4) &&

drivers/ide/sc1200.c

@@ -104,11 +104,12 @@ static u8 sc1200_udma_filter(ide_drive_t *drive)
 {
 	ide_hwif_t *hwif = drive->hwif;
 	ide_drive_t *mate = ide_get_pair_dev(drive);
-	u16 *mateid = mate->id;
+	u16 *mateid;
 	u8 mask = hwif->ultra_mask;
 
 	if (mate == NULL)
 		goto out;
+	mateid = mate->id;
 
 	if (ata_id_has_dma(mateid) && __ide_dma_bad_drive(mate) == 0) {
 		if ((mateid[ATA_ID_FIELD_VALID] & 4) &&

drivers/ieee1394/nodemgr.c

@@ -115,8 +115,14 @@ static int nodemgr_bus_read(struct csr1212_csr *csr, u64 addr, u16 length,
 	return error;
 }
 
+#define OUI_FREECOM_TECHNOLOGIES_GMBH 0x0001db
+
 static int nodemgr_get_max_rom(quadlet_t *bus_info_data, void *__ci)
 {
+	/* Freecom FireWire Hard Drive firmware bug */
+	if (be32_to_cpu(bus_info_data[3]) >> 8 == OUI_FREECOM_TECHNOLOGIES_GMBH)
+		return 0;
+
 	return (be32_to_cpu(bus_info_data[2]) >> 8) & 0x3;
 }
 

drivers/md/bitmap.c

@@ -208,15 +208,18 @@ static void bitmap_checkfree(struct bitmap *bitmap, unsigned long page)
  */
 
 /* IO operations when bitmap is stored near all superblocks */
-static struct page *read_sb_page(mddev_t *mddev, long offset, unsigned long index)
+static struct page *read_sb_page(mddev_t *mddev, long offset,
+				 struct page *page,
+				 unsigned long index, int size)
 {
 	/* choose a good rdev and read the page from there */
 
 	mdk_rdev_t *rdev;
 	struct list_head *tmp;
-	struct page *page = alloc_page(GFP_KERNEL);
 	sector_t target;
 
+	if (!page)
+		page = alloc_page(GFP_KERNEL);
 	if (!page)
 		return ERR_PTR(-ENOMEM);
 
@@ -227,7 +230,9 @@ static struct page *read_sb_page(mddev_t *mddev, long offset, unsigned long inde
 
 		target = rdev->sb_start + offset + index * (PAGE_SIZE/512);
 
-		if (sync_page_io(rdev->bdev, target, PAGE_SIZE, page, READ)) {
+		if (sync_page_io(rdev->bdev, target,
+				 roundup(size, bdev_hardsect_size(rdev->bdev)),
+				 page, READ)) {
 			page->index = index;
 			attach_page_buffers(page, NULL); /* so that free_buffer will
 							  * quietly no-op */
@@ -544,7 +549,9 @@ static int bitmap_read_sb(struct bitmap *bitmap)
 
 		bitmap->sb_page = read_page(bitmap->file, 0, bitmap, bytes);
 	} else {
-		bitmap->sb_page = read_sb_page(bitmap->mddev, bitmap->offset, 0);
+		bitmap->sb_page = read_sb_page(bitmap->mddev, bitmap->offset,
+					       NULL,
+					       0, sizeof(bitmap_super_t));
 	}
 	if (IS_ERR(bitmap->sb_page)) {
 		err = PTR_ERR(bitmap->sb_page);
@@ -957,11 +964,16 @@ static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
 				 */
 				page = bitmap->sb_page;
 				offset = sizeof(bitmap_super_t);
+				read_sb_page(bitmap->mddev, bitmap->offset,
+					     page,
+					     index, count);
 			} else if (file) {
 				page = read_page(file, index, bitmap, count);
 				offset = 0;
 			} else {
-				page = read_sb_page(bitmap->mddev, bitmap->offset, index);
+				page = read_sb_page(bitmap->mddev, bitmap->offset,
+						    NULL,
+						    index, count);
 				offset = 0;
 			}
 			if (IS_ERR(page)) { /* read error */

drivers/media/dvb/b2c2/Kconfig

@@ -9,11 +9,11 @@ config DVB_B2C2_FLEXCOP
 	select DVB_STV0297 if !DVB_FE_CUSTOMISE
 	select DVB_BCM3510 if !DVB_FE_CUSTOMISE
 	select DVB_LGDT330X if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
 	select DVB_S5H1420 if !DVB_FE_CUSTOMISE
 	select DVB_TUNER_ITD1000 if !DVB_FE_CUSTOMISE
 	select DVB_ISL6421 if !DVB_FE_CUSTOMISE
 	select DVB_CX24123 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Support for the digital TV receiver chip made by B2C2 Inc. included in
 	  Technisats PCI cards and USB boxes.

drivers/media/dvb/b2c2/flexcop-fe-tuner.c

@@ -628,12 +628,14 @@ int flexcop_frontend_init(struct flexcop_device *fc)
 	}
 
 	/* try the cable dvb (stv0297) */
+	fc->fc_i2c_adap[0].no_base_addr = 1;
 	fc->fe = dvb_attach(stv0297_attach, &alps_tdee4_stv0297_config, i2c);
 	if (fc->fe != NULL) {
 		fc->dev_type = FC_CABLE;
 		fc->fe->ops.tuner_ops.set_params = alps_tdee4_stv0297_tuner_set_params;
 		goto fe_found;
 	}
+	fc->fc_i2c_adap[0].no_base_addr = 0;
 
 	/* try the sky v2.3 (vp310/Samsung tbdu18132(tsa5059)) */
 	fc->fe = dvb_attach(mt312_attach,

drivers/media/dvb/b2c2/flexcop-i2c.c

@@ -47,8 +47,12 @@ static int flexcop_i2c_read4(struct flexcop_i2c_adapter *i2c,
 	int len = r100.tw_sm_c_100.total_bytes, /* remember total_bytes is buflen-1 */
 		ret;
 
-	r100.tw_sm_c_100.no_base_addr_ack_error = i2c->no_base_addr;
 	ret = flexcop_i2c_operation(i2c->fc, &r100);
+	if (ret != 0) {
+		deb_i2c("Retrying operation\n");
+		r100.tw_sm_c_100.no_base_addr_ack_error = i2c->no_base_addr;
+		ret = flexcop_i2c_operation(i2c->fc, &r100);
+	}
 	if (ret != 0) {
 		deb_i2c("read failed. %d\n", ret);
 		return ret;

drivers/media/dvb/bt8xx/Kconfig

@@ -8,7 +8,7 @@ config DVB_BT8XX
 	select DVB_OR51211 if !DVB_FE_CUSTOMISE
 	select DVB_LGDT330X if !DVB_FE_CUSTOMISE
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Support for PCI cards based on the Bt8xx PCI bridge. Examples are
 	  the Nebula cards, the Pinnacle PCTV cards, the Twinhan DST cards,

drivers/media/dvb/dvb-usb/Kconfig

@@ -24,8 +24,8 @@ config DVB_USB_A800
 	tristate "AVerMedia AverTV DVB-T USB 2.0 (A800)"
 	depends on DVB_USB
 	select DVB_DIB3000MC
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
 	select DVB_PLL if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the AVerMedia AverTV DVB-T USB 2.0 (A800) receiver.
 
@@ -34,7 +34,7 @@ config DVB_USB_DIBUSB_MB
 	depends on DVB_USB
 	select DVB_PLL if !DVB_FE_CUSTOMISE
 	select DVB_DIB3000MB
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Support for USB 1.1 and 2.0 DVB-T receivers based on reference designs made by
 	  DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-B demodulator.
@@ -55,7 +55,7 @@ config DVB_USB_DIBUSB_MC
 	tristate "DiBcom USB DVB-T devices (based on the DiB3000M-C/P) (see help for device list)"
 	depends on DVB_USB
 	select DVB_DIB3000MC
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Support for USB2.0 DVB-T receivers based on reference designs made by
 	  DiBcom (<http://www.dibcom.fr>) equipped with a DiB3000M-C/P demodulator.
@@ -73,11 +73,11 @@ config DVB_USB_DIB0700
 	select DVB_DIB7000M
 	select DVB_DIB3000MC
 	select DVB_S5H1411 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MT2266 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMIZE
 	select DVB_TUNER_DIB0070
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_MT2266 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_XC2028 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_XC5000 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Support for USB2.0/1.1 DVB receivers based on the DiB0700 USB bridge. The
 	  USB bridge is also present in devices having the DiB7700 DVB-T-USB
@@ -95,7 +95,7 @@ config DVB_USB_UMT_010
 	depends on DVB_USB
 	select DVB_PLL if !DVB_FE_CUSTOMISE
 	select DVB_DIB3000MC
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the HanfTek UMT-010 USB2.0 stick-sized DVB-T receiver.
 
@@ -107,11 +107,11 @@ config DVB_USB_CXUSB
 	select DVB_LGDT330X if !DVB_FE_CUSTOMISE
 	select DVB_MT352 if !DVB_FE_CUSTOMISE
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
 	select DVB_DIB7000P if !DVB_FE_CUSTOMISE
 	select DVB_TUNER_DIB0070 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_XC2028 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_MXL5005S if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the Conexant USB2.0 hybrid reference design.
 	  Currently, only DVB and ATSC modes are supported, analog mode
@@ -124,9 +124,9 @@ config DVB_USB_M920X
 	tristate "Uli m920x DVB-T USB2.0 support"
 	depends on DVB_USB
 	select DVB_MT352 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_TDA827X if !DVB_FE_CUSTOMISE
 	select DVB_TDA1004X if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_QT1010 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_TDA827X if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the MSI Mega Sky 580 USB2.0 DVB-T receiver.
 	  Currently, only devices with a product id of
@@ -137,7 +137,7 @@ config DVB_USB_GL861
 	tristate "Genesys Logic GL861 USB2.0 support"
 	depends on DVB_USB
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_QT1010 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the MSI Megasky 580 (55801) DVB-T USB2.0
 	  receiver with USB ID 0db0:5581.
@@ -146,7 +146,7 @@ config DVB_USB_AU6610
 	tristate "Alcor Micro AU6610 USB2.0 support"
 	depends on DVB_USB
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_QT1010 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the Sigmatek DVB-110 DVB-T USB2.0 receiver.
 
@@ -198,8 +198,8 @@ config DVB_USB_NOVA_T_USB2
 	tristate "Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 support"
 	depends on DVB_USB
 	select DVB_DIB3000MC
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
 	select DVB_PLL if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the Hauppauge WinTV-NOVA-T usb2 DVB-T USB2.0 receiver.
 
@@ -235,8 +235,8 @@ config DVB_USB_OPERA1
 config DVB_USB_AF9005
 	tristate "Afatech AF9005 DVB-T USB1.1 support"
 	depends on DVB_USB && EXPERIMENTAL
-	select MEDIA_TUNER_MT2060 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_QT1010 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the Afatech AF9005 based DVB-T USB1.1 receiver
 	  and the TerraTec Cinergy T USB XE (Rev.1)
@@ -284,7 +284,7 @@ config DVB_USB_DTV5100
 	tristate "AME DTV-5100 USB2.0 DVB-T support"
 	depends on DVB_USB
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_QT1010 if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the AME DTV-5100 USB2.0 DVB-T receiver.
 
@@ -293,9 +293,9 @@ config DVB_USB_AF9015
 	depends on DVB_USB && EXPERIMENTAL
 	select DVB_AF9013
 	select DVB_PLL              if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MT2060   if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_QT1010   if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MT2060   if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_QT1010   if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_TDA18271 if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_MXL5005S if !MEDIA_TUNER_CUSTOMIZE
 	help
 	  Say Y here to support the Afatech AF9015 based DVB-T USB2.0 receiver

drivers/media/dvb/dvb-usb/dib0700_devices.c

@@ -446,13 +446,13 @@ static int stk7700ph_tuner_attach(struct dvb_usb_adapter *adap)
 		== NULL ? -ENODEV : 0;
 }
 
-#define DEFAULT_RC_INTERVAL 150
+#define DEFAULT_RC_INTERVAL 50
 
 static u8 rc_request[] = { REQUEST_POLL_RC, 0 };
 
 /* Number of keypresses to ignore before start repeating */
-#define RC_REPEAT_DELAY 2
-#define RC_REPEAT_DELAY_V1_20 5
+#define RC_REPEAT_DELAY 6
+#define RC_REPEAT_DELAY_V1_20 10
 
 
 

drivers/media/dvb/ttpci/Kconfig

@@ -106,7 +106,7 @@ config DVB_BUDGET_CI
 	select DVB_TDA1004X if !DVB_FE_CUSTOMISE
 	select DVB_LNBP21 if !DVB_FE_CUSTOMISE
 	select DVB_TDA10023 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_TDA827X if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_TDA827X if !MEDIA_TUNER_CUSTOMIZE
 	select VIDEO_IR
 	help
 	  Support for simple SAA7146 based DVB cards

drivers/media/video/compat_ioctl32.c

@@ -831,7 +831,7 @@ long v4l_compat_ioctl32(struct file *file, unsigned int cmd, unsigned long arg)
 {
 	int ret = -ENOIOCTLCMD;
 
-	if (!file->f_op->ioctl)
+	if (!file->f_op->ioctl && !file->f_op->unlocked_ioctl)
 		return ret;
 
 	switch (cmd) {

drivers/media/video/cx18/Kconfig

@@ -9,7 +9,7 @@ config VIDEO_CX18
 	select VIDEO_CX2341X
 	select VIDEO_CS5345
 	select DVB_S5H1409 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MXL5005S if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_MXL5005S if !MEDIA_TUNER_CUSTOMIZE
 	---help---
 	  This is a video4linux driver for Conexant cx23418 based
 	  PCI combo video recorder devices.

drivers/media/video/cx23885/Kconfig

@@ -11,16 +11,16 @@ config VIDEO_CX23885
 	select VIDEO_CX25840
 	select VIDEO_CX2341X
 	select DVB_DIB7000P if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_MT2131 if !DVB_FE_CUSTOMISE
 	select DVB_S5H1409 if !DVB_FE_CUSTOMISE
 	select DVB_S5H1411 if !DVB_FE_CUSTOMISE
 	select DVB_LGDT330X if !DVB_FE_CUSTOMISE
 	select DVB_ZL10353 if !DVB_FE_CUSTOMISE
+	select DVB_TDA10048 if !DVB_FE_CUSTOMIZE
+	select MEDIA_TUNER_MT2131 if !MEDIA_TUNER_CUSTOMIZE
 	select MEDIA_TUNER_XC2028 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_XC5000 if !DVB_FE_CUSTOMIZE
-	select DVB_TDA10048 if !DVB_FE_CUSTOMIZE
 	---help---
 	  This is a video4linux driver for Conexant 23885 based
 	  TV cards.

drivers/media/video/cx88/Kconfig

@@ -56,12 +56,12 @@ config VIDEO_CX88_DVB
 	select DVB_NXT200X if !DVB_FE_CUSTOMISE
 	select DVB_CX24123 if !DVB_FE_CUSTOMISE
 	select DVB_ISL6421 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
 	select DVB_S5H1411 if !DVB_FE_CUSTOMISE
 	select DVB_CX24116 if !DVB_FE_CUSTOMISE
 	select DVB_STV0299 if !DVB_FE_CUSTOMISE
 	select DVB_STV0288 if !DVB_FE_CUSTOMISE
 	select DVB_STB6000 if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	---help---
 	  This adds support for DVB/ATSC cards based on the
 	  Conexant 2388x chip.

drivers/media/video/em28xx/em28xx-video.c

@@ -549,10 +549,11 @@ static int em28xx_config(struct em28xx *dev)
 static void em28xx_config_i2c(struct em28xx *dev)
 {
 	struct v4l2_routing route;
+	int zero = 0;
 
 	route.input = INPUT(dev->ctl_input)->vmux;
 	route.output = 0;
-	em28xx_i2c_call_clients(dev, VIDIOC_INT_RESET, NULL);
+	em28xx_i2c_call_clients(dev, VIDIOC_INT_RESET, &zero);
 	em28xx_i2c_call_clients(dev, VIDIOC_INT_S_VIDEO_ROUTING, &route);
 	em28xx_i2c_call_clients(dev, VIDIOC_STREAMON, NULL);
 }

drivers/media/video/gspca/gspca.c

@@ -1264,10 +1264,10 @@ static int vidioc_s_jpegcomp(struct file *file, void *priv,
 	struct gspca_dev *gspca_dev = priv;
 	int ret;
 
-	if (mutex_lock_interruptible(&gspca_dev->usb_lock))
-		return -ERESTARTSYS;
 	if (!gspca_dev->sd_desc->set_jcomp)
 		return -EINVAL;
+	if (mutex_lock_interruptible(&gspca_dev->usb_lock))
+		return -ERESTARTSYS;
 	ret = gspca_dev->sd_desc->set_jcomp(gspca_dev, jpegcomp);
 	mutex_unlock(&gspca_dev->usb_lock);
 	return ret;

drivers/media/video/pvrusb2/Kconfig

@@ -42,7 +42,7 @@ config VIDEO_PVRUSB2_DVB
 	select DVB_S5H1411 if !DVB_FE_CUSTOMISE
 	select DVB_TDA10048 if !DVB_FE_CUSTOMIZE
 	select MEDIA_TUNER_TDA18271 if !DVB_FE_CUSTOMIZE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	select MEDIA_TUNER_TDA8290 if !DVB_FE_CUSTOMIZE
 	---help---
 

drivers/media/video/saa7134/Kconfig

@@ -34,9 +34,9 @@ config VIDEO_SAA7134_DVB
 	select DVB_NXT200X if !DVB_FE_CUSTOMISE
 	select DVB_TDA10086 if !DVB_FE_CUSTOMISE
 	select DVB_TDA826X if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_TDA827X if !DVB_FE_CUSTOMISE
 	select DVB_ISL6421 if !DVB_FE_CUSTOMISE
-	select MEDIA_TUNER_SIMPLE if !DVB_FE_CUSTOMISE
+	select MEDIA_TUNER_TDA827X if !MEDIA_TUNER_CUSTOMIZE
+	select MEDIA_TUNER_SIMPLE if !MEDIA_TUNER_CUSTOMIZE
 	---help---
 	  This adds support for DVB cards based on the
 	  Philips saa7134 chip.

drivers/message/fusion/mptscsih.c

@@ -2008,6 +2008,9 @@ mptscsih_host_reset(struct scsi_cmnd *SCpnt)
 		return FAILED;
 	}
 
+	/* make sure we have no outstanding commands at this stage */
+	mptscsih_flush_running_cmds(hd);
+
 	ioc = hd->ioc;
 	printk(MYIOC_s_INFO_FMT "attempting host reset! (sc=%p)\n",
 	    ioc->name, SCpnt);

drivers/net/bnx2.c

@@ -543,9 +543,9 @@ bnx2_free_rx_mem(struct bnx2 *bp)
 		for (j = 0; j < bp->rx_max_pg_ring; j++) {
 			if (rxr->rx_pg_desc_ring[j])
 				pci_free_consistent(bp->pdev, RXBD_RING_SIZE,
-						    rxr->rx_pg_desc_ring[i],
-						    rxr->rx_pg_desc_mapping[i]);
-			rxr->rx_pg_desc_ring[i] = NULL;
+						    rxr->rx_pg_desc_ring[j],
+						    rxr->rx_pg_desc_mapping[j]);
+			rxr->rx_pg_desc_ring[j] = NULL;
 		}
 		if (rxr->rx_pg_ring)
 			vfree(rxr->rx_pg_ring);

drivers/net/e1000e/ich8lan.c

@@ -1893,12 +1893,17 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 		ctrl |= E1000_CTRL_PHY_RST;
 	}
 	ret_val = e1000_acquire_swflag_ich8lan(hw);
+	/* Whether or not the swflag was acquired, we need to reset the part */
 	hw_dbg(hw, "Issuing a global reset to ich8lan");
 	ew32(CTRL, (ctrl | E1000_CTRL_RST));
 	msleep(20);
 
-	/* release the swflag because it is not reset by hardware reset */
-	e1000_release_swflag_ich8lan(hw);
+	if (!ret_val) {
+		/* release the swflag because it is not reset by
+		 * hardware reset
+		 */
+		e1000_release_swflag_ich8lan(hw);
+	}
 
 	ret_val = e1000e_get_auto_rd_done(hw);
 	if (ret_val) {

drivers/net/enc28j60.c

@@ -959,7 +959,7 @@ static void enc28j60_hw_rx(struct net_device *ndev)
 			ndev->stats.rx_packets++;
 			ndev->stats.rx_bytes += len;
 			ndev->last_rx = jiffies;
-			netif_rx(skb);
+			netif_rx_ni(skb);
 		}
 	}
 	/*

drivers/net/jme.h

@@ -22,7 +22,7 @@
  */
 
 #ifndef __JME_H_INCLUDED__
-#define __JME_H_INCLUDEE__
+#define __JME_H_INCLUDED__
 
 #define DRV_NAME	"jme"
 #define DRV_VERSION	"1.0.3"

drivers/net/phy/mdio_bus.c

@@ -105,8 +105,6 @@ int mdiobus_register(struct mii_bus *bus)
 		return -EINVAL;
 	}
 
-	bus->state = MDIOBUS_REGISTERED;
-
 	mutex_init(&bus->mdio_lock);
 
 	if (bus->reset)
@@ -123,6 +121,9 @@ int mdiobus_register(struct mii_bus *bus)
 		}
 	}
 
+	if (!err)
+		bus->state = MDIOBUS_REGISTERED;
+
 	pr_info("%s: probed\n", bus->name);
 
 	return err;