[PATCH] libertas: Purge non-mesh ioctls

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/README

@@ -40,64 +40,11 @@ NAME
 SYNOPSIS
 	iwpriv <ethX> <command> [sub-command] ...
 
-	iwpriv ethX version
-	iwpriv ethX scantype [sub-command]
-	iwpriv ethX getSNR <n>
-	iwpriv ethX getNF <n>
-	iwpriv ethX getRSSI <n>
-	iwpriv ethX setrxant <n>
-	iwpriv ethX getrxant
-	iwpriv ethX settxant <n>
-	iwpriv ethX gettxant
-	iwpriv ethX authalgs <n>
-	iwpriv ethX pre-TBTT <n>
-	iwpriv ethX 8021xauthalgs <n>
-	iwpriv ethX encryptionmode <n>
 	iwpriv ethX setregioncode <n>
 	iwpriv ethX getregioncode
-	iwpriv ethX setbcnavg <n>
-	iwpriv ethX getbcnavg
-	iwpriv ethX setdataavg <n>
-	iwpriv ethX setlisteninter <n>
-	iwpriv ethX getlisteninter
-	iwpriv ethX setmultipledtim <n>
-	iwpriv ethX getmultipledtim
-	iwpriv ethX atimwindow <n>
-	iwpriv ethX deauth
-	iwpriv ethX adhocstop
-	iwpriv ethX radioon
-	iwpriv ethX radiooff
-	iwpriv ethX reasso-on
-	iwpriv ethX reasso-off
-	iwpriv ethX scanmode  [sub-command]
-	iwpriv ethX setwpaie <n>
-	iwpriv ethX wlanidle-off
-	iwpriv ethX wlanidle-on
-	iwpriv ethX getcis
-	iwpriv ethX getlog
-	iwpriv ethX getadhocstatus
-	iwpriv ethX adhocgrate <n>
-
-Version 4 Command:
-	iwpriv ethX inactvityto <n>
-	iwpriv ethX sleeppd <n>
-	iwpriv ethX enable11d <n>
-	iwpriv ethX tpccfg <n>
-	iwpriv ethX powercfg <n>
-	iwpriv ethX setafc <n>
-	iwpriv ethX getafc
 
 Version 5 Command:
 	iwpriv ethX ledgpio <n>
-	iwpriv ethX scanprobes <n>
-	iwpriv ethX lolisteninter <n>
-	iwpriv ethX rateadapt <n> <m>
-	iwpriv ethX txcontrol <n>
-	iwpriv ethX psnullinterval <n>
-	iwpriv ethX prescan <n>
-	iwpriv ethX getrxinfo
-	iwpriv ethX gettxrate
-	iwpriv ethX beaconinterval
 
 BT Commands:
 	The blinding table (BT) contains a list of mac addresses that should be
@@ -150,114 +97,6 @@ DESCRIPTION
 	The ethX parameter specifies the network device that is to be used to
 		perform this command on. it could be eth0, eth1 etc.
 
-version
-	This is used to get the current version of the driver and the firmware.
-
-scantype
-	This command is used to set the scan type to be used by the driver in
-	the scan command. This setting will not be used while performing a scan
-	for a specific SSID, as it is always done with scan type being active.
-
-	where the sub-commands are: -
-			active 	-- to set the scan type to active
-			passive -- to set the scan type to passive
-			get 	-- to get the scan type set in the driver
-
-getSNR
-	This command gets the average and non average value of Signal to Noise
-	Ratio of Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	If no value is given, all four values are returned in the order mentioned
-	above.
-
-	Note: This command is available only when STA is connected.
-
-getRSSI
-	This command gets the average and non average value os Receive Signal
-	Strength of Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	Note: This command is available only when STA is connected.
-
-getNF
-	This command gets the average and non average value of Noise Floor of
-	Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	Note: This command is available only when STA is connected.
-
-setrxant
-	This command is used to set the mode for Rx antenna.
-
-	The options that can be sent are:-
-			1 	-- Antenna 1.
-			2 	-- Antenna 2.
-			0xFFFF 	-- Diversity.
-
-	Usage:
-		iwpriv ethX setrxant 0x01: select Antenna 1.
-
-getrxant
-	This command is used to get the mode for Rx antenna.
-
-
-settxant
-	This command is used to set the mode for Tx antenna.
-		The options that can be sent are:-
-			1 	-- Antenna 1.
-			2 	-- Antenna 2.
-			0xFFFF 	-- Diversity.
-	Usage:
-		iwpriv ethX settxant 0x01: select Antenna 1.
-
-gettxant
-	This command is used to get the mode for Tx antenna.
-
-authalgs
-	This command is used by the WPA supplicant to set the authentication
-	algorithms in the station.
-
-8021xauthalgs
-	This command is used by the WPA supplicant to set the 8021.x authentication algorithm type
-	station.
-
-	where values can be:-
-			1 	-- None
-			2 	-- LEAP
-			4 	-- TLS
-			8 	-- TTLs
-			16	-- MD5
-
-
-encryptionmode
-	This command is used by the WPA supplicant to set the encryption algorithm.
-
-	where values can be:-
-			0 	-- NONE
-			1 	-- WEP40
-			2 	-- TKIP
-			3 	-- CCMP
-			4 	-- WEP104
-
-pre-TBTT
-	This command is used to set pre-TBTT time period where value is in microseconds.
-
 setregioncode
 	This command is used to set the region code in the station.
 	where value is 'region code' for various regions like
@@ -270,114 +109,6 @@ getregioncode
 	This command is used to get the region code information set in the
 	station.
 
-setbcnavg
-	Set the weighting factor for calculating RSSI.
-
-getbcnavg
-	Get weighting factor for calculating RSSI.
-
-setdataavg
-	Set the weighting factor for calculating SNR.
-
-setlisteninter
-	This command is used to set the listen interval in the
-	station.
-
-	where the value ranges between 1 - 255
-
-getlisteninter
-	This command is used to get the listen interval value set in the
-	station.
-
-setmultipledtim
-	This command is used to set the multiple dtim value in the
-	station.
-		where the value is 1,2,3,4,5,0xfffe
-		0xfffe means the firmware will use listen interval in association
-		command for waking up
-
-getmultipledtim
-	This command is used to get the multiple dtim value set in the station.
-
-atimwindow
-	This command is used to set the atim value in the
-	station.
-
-	where the value ranges between 0 - 50
-
-deauth
-	This command is used to send the de-authentication to the AP with which
-	the station is associated. This command is valid only when
-	station is in Infrastructure mode.
-
-	Note: This command is available only when STA is connected.
-
-adhocstop
-	This command is used to stop beacon transmission from the station and
-	go into idle state in ad-hoc mode.
-
-	Note: This command is available only when STA is connected.
-
-radioon
-	This command is used to turn on the RF antenna.
-
-radiooff
-	This command is sued to turn off the RF antenna.
-
-scanmode
-	This command is used to set the station to scan for either IBSS
-	networks or BSS networks or both BSS and IBSS networks. This
-	command can be used with sub commands,
-
-	where the value for
-			bss 	-- Scan All the BSS networks.
-			ibss 	-- Scan All the IBSS networks.
-			any 	-- Scan both BSS and IBSS networks.
-
-
-
-setwpaie
-	This command is used by WPA supplicant to send the WPA-IE to the driver.
-
-wlanidle-off
-	This command is used to get into idle state.
-
-	Note: This command is available only when STA is connected.
-
-wlanidle-on
-	This command is used to get off the idle state.
-
-	Note: This command is available only when STA is connected.
-
-
-getlog
-	This command is used to get the 802.11 statistics available in the
-		station.
-
-	Note: This command is available only when STA is connected.
-
-getadhocstatus
-	This command is used to get the ad-hoc Network Status.
-
-	The various status codes are:
-		AdhocStarted
-		AdhocJoined
-		AdhocIdle
-		InfraMode
-		AutoUnknownMode
-
-	Note: This command is available only when STA is connected.
-
-adhocgrate
-	This command is used to enable(1) g_rate, Disable(0) g_rate
-	and request(2) the status which g_rate is disabled/enabled,
-	for Ad-hoc creator.
-
-	where value is:-
-		0	-- Disabled
-		1	-- Enabled
-		2	-- Get
-
 ledgpio
 	This command is used to set/get LEDs.
 
@@ -400,253 +131,6 @@ ledgpio
 	Note: LED0 is invalid
 	Note: Maximum Number of LEDs are 16.
 
-inactivityto
-	This command is used by the host to set/get the inactivity timeout value,
-	which specifies when WLAN device is put to sleep.
-
-	Usage:
-		iwpriv ethX inactivityto [<timeout>]
-
-	where the parameter are:
-		timeout: timeout value in milliseconds.
-
-	Example:
-		iwpriv eth1 inactivityto
-			"get the timeout value"
-
-		iwpriv eth1 inactivityto X
-			"set timeout value to X ms"
-
-
-sleeppd
-	This command is used to configure the sleep period of the WLAN device.
-
-	Usage:
-		iwpriv ethX sleeppd [<sleep period>]
-
-	where the parameter are:
-		Period: sleep period in milliseconds. Range 10~60.
-
-	Example:
-		iwpriv eth1 sleeppd 10
-			"set period as 10 ms"
-		iwpriv eth1 sleeppd
-			"get the sleep period configuration"
-
-enable11d
-	This command is used to control 11d
-	where value is:-
-		1	-- Enabled
-		0	-- Disabled
-		2	-- Get
-
-
-
-
-tpccfg
-	Enables or disables automatic transmit power control.
-
-	The first parameter turns this feature on (1) or off (0).  When turning
-	on, the user must also supply four more parameters in the following
-	order:
-		-UseSNR (Use SNR (in addition to PER) for TPC algorithm),
-		-P0 (P0 power level for TPC),
-		-P1 (P1 power level for TPC),
-		-P2 (P2 power level for TPC).
-
-	Usage:
-		iwpriv ethX tpccfg: Get current configuration
-		iwpriv ethX tpccfg 0: disable auto TPC
-		iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR;
-							     P0=0x05; P1=0x0a; P2=0x0d;
-		iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR;
-							     P0=0x05; P1=0x0a; P2=0x0d.
-
-powercfg
-	Enables or disables power adaptation.
-
-	The first parameter turns this feature on (1) or off (0).  When turning
-	on, the user must also supply three more parameters in the following
-	order:
-		-P0 (P0 power level for Power Adaptation),
-		-P1 (P1 power level for Power Adaptation),
-		-P2 (P2 power level for Power Adaptation).
-
-	Usage:
-		iwpriv ethX powercfg: Get current configuration
-		iwpriv ethX powercfg 0: disable power adaptation
-		iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation;
-						       P0=0x0d; P1=0x0f; P2=0x12.
-
-getafc
-	This command returns automatic frequency control parameters.  It returns
-	three integers:
-		-P0: automatic is on (1), or off (0),
-		-P1: current timing offset in PPM (part per million), and
-		-P2: current frequency offset in PPM.
-
-setafc
-	Set automatic frequency control options.
-
-	The first parameter turns automatic on (1) or off (0).
-	The user must supply two more parameters in either case, in the following
-  order:
-
-  When auto is on:
-
-		-P0 (automatic adjustment frequency threshold in PPM),
-		-P1 (automatic adjustment period in beacon period),
-
-  When auto is off:
-
-		-P0 (manual adjustment timing offset in PPM), and
-		-P1 (manual adjustment frequency offset in PPM).
-
-	Usage:
-		iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy
-    offset are 10 PPM.
-
-		iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment,
-    frequency threshold 10 PPM, for every 10 beacon periods.
-
-
-
-scanprobes
-	This command sets number of probe requests per channel.
-
-	Usage:
-		iwpriv ethX scanprobes 3 (set scan probes to 3)
-		iwpriv ethX scanprobes   (get scan probes)
-
-lolisteninter
-	This command sets the value of listen interval.
-
-	Usage:
-	iwpriv ethX lolisteninter 234 (set the lolisteninter to 234)
-	iwpriv ethX lolisteninter     (get the lolisteninter value)
-
-rateadapt
-	This command sets the data rates bitmap.
-	Where <n>
-		0: Disable auto rate adapt
-		1: Enable auto rate adapt
-
-	      <m>
-		 data rate bitmap
-			Bit	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			12-15	Reserved
-
-	Usage:
-	iwpriv ethX rateadapt
-			read the currect data rate setting
-	iwpriv ethX rateadapt 1 0x07
-			enable auto data rate adapt and
-			data rates are 1Mbps, 2Mbsp and 5.5Mbps
-
-
-txcontrol
-	This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis.
-
-	Where value <n> is:
-	    if bit[4] == 1:
-		bit[3:0]        -- 0   1   2   3   4   5   6   7   8   9   10   11   12   13-16
-		Data Rate(Mbps) -- 1   2   5.5 11  Rsv 6   9   12  18  24  36   48   54   Rsv
-
-	    bit[12:8]
-		if bit[12] == 1, bit[11:8] specifies the Tx retry limit.
-
-	    bit[14:13] specifies per packet ack policy:
-		bit[14:13]
-		     1  0	use immediate ack policy for this packet
-		     1  1       use no ack policy for this packet
-		     0  x	use the per-packet ack policy setting
-
-	Usage:
-	iwpriv ethX txcontrol 0x7513
-			Use no-ack policy, 5 retires for Tx, 11Mbps rate
-
-
-
-psnullinterval
-	This command is used to set/request NULL package interval for Power Save
-	under infrastructure mode.
-
-	where value is:-
-		-1	-- Disabled
-		n>0	-- Set interval as n (seconds)
-
-prescan
-	This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap
-
-	where value is:-
-		0	-- Disabled
-		1	-- Enabled
-		2       -- Get
-
-getrxinfo
-	This command gets non average value of Signal to Noise Ratio of Data and rate index.
-
-	The following table shows RateIndex and Rate
-
-		     RateIndex	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			13-15	Reserved
-
-gettxrate
-	This command gets current Tx rate index of the first packet associated with Rate Adaptation.
-
-	The following table shows RateIndex and Rate
-
-		     RateIndex	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			13-15	Reserved
-
-bcninterval
-	This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc
-	beacon interval when no argument is given. The valid beacon interval is between 20 - 1000,
-	default beacon interval is 100.
-
-	Usage:
-		iwpriv ethX bcninterval 100  (set adhoc beacon interval to 100)
-		iwpriv ethX bcninterval      (get adhoc beacon interval)
-
 fwt_add
 	This command is used to insert an entry into the FWT table. The list of
 	parameters must follow the following structure:

drivers/net/wireless/libertas/join.c

@@ -96,20 +96,6 @@ int libertas_send_deauth(wlan_private * priv)
 	return ret;
 }
 
-int libertas_do_adhocstop_ioctl(wlan_private * priv)
-{
-	wlan_adapter *adapter = priv->adapter;
-	int ret = 0;
-
-	if (adapter->mode == IW_MODE_ADHOC &&
-	    adapter->connect_status == libertas_connected)
-		ret = libertas_stop_adhoc_network(priv);
-	else
-		ret = -ENOTSUPP;
-
-	return ret;
-}
-
 /**
  *  @brief Associate to a specific BSS discovered in a scan
  *
@@ -261,127 +247,6 @@ int libertas_send_deauthentication(wlan_private * priv)
 				     0, cmd_option_waitforrsp, 0, NULL);
 }
 
-/**
- *  @brief Set Idle Off
- *
- *  @param priv         A pointer to wlan_private structure
- *  @return             0 --success, otherwise fail
- */
-int libertas_idle_off(wlan_private * priv)
-{
-	wlan_adapter *adapter = priv->adapter;
-	int ret = 0;
-	const u8 zeromac[] = { 0, 0, 0, 0, 0, 0 };
-	int i;
-
-	ENTER();
-
-	if (adapter->connect_status == libertas_disconnected) {
-		if (adapter->mode == IW_MODE_INFRA) {
-			if (memcmp(adapter->previousbssid, zeromac,
-				   sizeof(zeromac)) != 0) {
-
-				lbs_pr_debug(1, "Previous SSID = %s\n",
-				       adapter->previousssid.ssid);
-				lbs_pr_debug(1, "Previous BSSID = "
-				       "%02x:%02x:%02x:%02x:%02x:%02x:\n",
-				       adapter->previousbssid[0],
-				       adapter->previousbssid[1],
-				       adapter->previousbssid[2],
-				       adapter->previousbssid[3],
-				       adapter->previousbssid[4],
-				       adapter->previousbssid[5]);
-
-				i = libertas_find_SSID_in_list(adapter,
-						   &adapter->previousssid,
-						   adapter->previousbssid,
-						   adapter->mode);
-
-				if (i < 0) {
-					libertas_send_specific_BSSID_scan(priv,
-							      adapter->
-							      previousbssid,
-							      1);
-					i = libertas_find_SSID_in_list(adapter,
-							   &adapter->
-							   previousssid,
-							   adapter->
-							   previousbssid,
-							   adapter->mode);
-				}
-
-				if (i < 0) {
-					/* If the BSSID could not be found, try just the SSID */
-					i = libertas_find_SSID_in_list(adapter,
-							   &adapter->
-							   previousssid, NULL,
-							   adapter->mode);
-				}
-
-				if (i < 0) {
-					libertas_send_specific_SSID_scan(priv,
-							     &adapter->
-							     previousssid,
-							     1);
-					i = libertas_find_SSID_in_list(adapter,
-							   &adapter->
-							   previousssid, NULL,
-							   adapter->mode);
-				}
-
-				if (i >= 0) {
-					ret =
-					    wlan_associate(priv,
-							   &adapter->
-							   scantable[i]);
-				}
-			}
-		} else if (adapter->mode == IW_MODE_ADHOC) {
-			ret = libertas_prepare_and_send_command(priv,
-						    cmd_802_11_ad_hoc_start,
-						    0,
-						    cmd_option_waitforrsp,
-						    0, &adapter->previousssid);
-		}
-	}
-	/* else it is connected */
-
-	lbs_pr_debug(1, "\nwlanidle is off");
-	LEAVE();
-	return ret;
-}
-
-/**
- *  @brief Set Idle On
- *
- *  @param priv         A pointer to wlan_private structure
- *  @return             0 --success, otherwise fail
- */
-int libertas_idle_on(wlan_private * priv)
-{
-	wlan_adapter *adapter = priv->adapter;
-	int ret = 0;
-
-	if (adapter->connect_status == libertas_connected) {
-		if (adapter->mode == IW_MODE_INFRA) {
-			lbs_pr_debug(1, "Previous SSID = %s\n",
-			       adapter->previousssid.ssid);
-			memmove(&adapter->previousssid,
-				&adapter->curbssparams.ssid,
-				sizeof(struct WLAN_802_11_SSID));
-			libertas_send_deauth(priv);
-
-		} else if (adapter->mode == IW_MODE_ADHOC) {
-			ret = libertas_stop_adhoc_network(priv);
-		}
-
-	}
-
-	lbs_pr_debug(1, "\nwlanidle is on");
-
-	return ret;
-}
-
 /**
  *  @brief This function prepares command of authenticate.
  *

drivers/net/wireless/libertas/join.h

@@ -37,10 +37,6 @@ extern int libertas_ret_80211_disassociate(wlan_private * priv,
 extern int libertas_ret_80211_associate(wlan_private * priv,
 				     struct cmd_ds_command *resp);
 
-extern int libertas_idle_on(wlan_private * priv);
-extern int libertas_idle_off(wlan_private * priv);
-
-extern int libertas_do_adhocstop_ioctl(wlan_private * priv);
 extern int libertas_reassociation_thread(void *data);
 
 struct WLAN_802_11_SSID;

drivers/net/wireless/libertas/wext.c

@@ -986,136 +986,17 @@ static const struct iw_priv_args wlan_private_args[] = {
 	/*
 	 * { cmd, set_args, get_args, name }
 	 */
-	{
-	 WLANSCAN_TYPE,
-	 IW_PRIV_TYPE_CHAR | 8,
-	 IW_PRIV_TYPE_CHAR | 8,
-	 "scantype"},
-
-	{
-	 WLAN_SETINT_GETINT,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 ""},
-	{
-	 WLANNF,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getNF"},
-	{
-	 WLANRSSI,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getRSSI"},
-	{
-	 WLANENABLE11D,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "enable11d"},
-	{
-	 WLANADHOCGRATE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "adhocgrate"},
-
-	{
-	 WLAN_SUBCMD_SET_PRESCAN,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "prescan"},
-	{
-	 WLAN_SETONEINT_GETONEINT,
-	 IW_PRIV_TYPE_INT | 1,
-	 IW_PRIV_TYPE_INT | 1,
-	 ""},
-	{
-	 WLAN_BEACON_INTERVAL,
-	 IW_PRIV_TYPE_INT | 1,
-	 IW_PRIV_TYPE_INT | 1,
-	 "bcninterval"},
-	{
-	 WLAN_LISTENINTRVL,
-	 IW_PRIV_TYPE_INT | 1,
-	 IW_PRIV_TYPE_INT | 1,
-	 "lolisteninter"},
-	{
-	 WLAN_TXCONTROL,
-	 IW_PRIV_TYPE_INT | 1,
-	 IW_PRIV_TYPE_INT | 1,
-	 "txcontrol"},
-	{
-	 WLAN_NULLPKTINTERVAL,
-	 IW_PRIV_TYPE_INT | 1,
-	 IW_PRIV_TYPE_INT | 1,
-	 "psnullinterval"},
 	/* Using iwpriv sub-command feature */
 	{
 	 WLAN_SETONEINT_GETNONE,	/* IOCTL: 24 */
 	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
 	 IW_PRIV_TYPE_NONE,
 	 ""},
-
-	{
-	 WLAN_SUBCMD_SETRXANTENNA,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setrxant"},
-	{
-	 WLAN_SUBCMD_SETTXANTENNA,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "settxant"},
-	{
-	 WLANSETENCRYPTIONMODE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "encryptionmode",
-	 },
 	{
 	 WLANSETREGION,
 	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
 	 IW_PRIV_TYPE_NONE,
 	 "setregioncode"},
-	{
-	 WLAN_SET_LISTEN_INTERVAL,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setlisteninter"},
-	{
-	 WLAN_SET_MULTIPLE_DTIM,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setmultipledtim"},
-	{
-	 WLAN_SET_ATIM_WINDOW,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "atimwindow"},
-	{
-	 WLANSETBCNAVG,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setbcnavg"},
-	{
-	 WLANSETDATAAVG,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "setdataavg"},
-	{
-	 WLAN_SET_LINKMODE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "linkmode"},
-	{
-	 WLAN_SET_RADIOMODE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "radiomode"},
-	{
-	 WLAN_SET_DEBUGMODE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 IW_PRIV_TYPE_NONE,
-	 "debugmode"},
 	{
 	 WLAN_SUBCMD_MESH_SET_TTL,
 	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
@@ -1131,41 +1012,6 @@ static const struct iw_priv_args wlan_private_args[] = {
 	 IW_PRIV_TYPE_NONE,
 	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
 	 "getregioncode"},
-	{
-	 WLAN_GET_LISTEN_INTERVAL,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getlisteninter"},
-	{
-	 WLAN_GET_MULTIPLE_DTIM,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getmultipledtim"},
-	{
-	 WLAN_GET_TX_RATE,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "gettxrate"},
-	{
-	 WLANGETBCNAVG,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "getbcnavg"},
-	{
-	 WLAN_GET_LINKMODE,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "get_linkmode"},
-	{
-	 WLAN_GET_RADIOMODE,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "get_radiomode"},
-	{
-	 WLAN_GET_DEBUGMODE,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
-	 "get_debugmode"},
 	{
 	 WLAN_SUBCMD_FWT_CLEANUP,
 	 IW_PRIV_TYPE_NONE,
@@ -1181,61 +1027,11 @@ static const struct iw_priv_args wlan_private_args[] = {
 	 IW_PRIV_TYPE_NONE,
 	 IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
 	 "mesh_get_ttl"},
-	{
-	 WLAN_SETNONE_GETTWELVE_CHAR,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | 12,
-	 ""},
-	{
-	 WLAN_SUBCMD_GETRXANTENNA,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | 12,
-	 "getrxant"},
-	{
-	 WLAN_SUBCMD_GETTXANTENNA,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | 12,
-	 "gettxant"},
-	{
-	 WLAN_GET_TSF,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | 12,
-	 "gettsf"},
 	{
 	 WLAN_SETNONE_GETNONE,
 	 IW_PRIV_TYPE_NONE,
 	 IW_PRIV_TYPE_NONE,
 	 ""},
-	{
-	 WLANDEAUTH,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "deauth"},
-	{
-	 WLANADHOCSTOP,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "adhocstop"},
-	{
-	 WLANRADIOON,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "radioon"},
-	{
-	 WLANRADIOOFF,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "radiooff"},
-	{
-	 WLANWLANIDLEON,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "wlanidle-on"},
-	{
-	 WLANWLANIDLEOFF,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_NONE,
-	 "wlanidle-off"},
 	{
 	 WLAN_SUBCMD_FWT_RESET,
 	 IW_PRIV_TYPE_NONE,
@@ -1298,86 +1094,16 @@ static const struct iw_priv_args wlan_private_args[] = {
 	 IW_PRIV_TYPE_CHAR | 128,
 	 IW_PRIV_TYPE_CHAR | 128,
 	 "fwt_list_route"},
-	{
-	 WLANSCAN_MODE,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "scanmode"},
-	{
-	 WLAN_GET_ADHOC_STATUS,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 "getadhocstatus"},
-	{
-	 WLAN_SETNONE_GETWORDCHAR,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | 128,
-	 ""},
-	{
-	 WLANGETLOG,
-	 IW_PRIV_TYPE_NONE,
-	 IW_PRIV_TYPE_CHAR | GETLOG_BUFSIZE,
-	 "getlog"},
 	{
 	 WLAN_SET_GET_SIXTEEN_INT,
 	 IW_PRIV_TYPE_INT | 16,
 	 IW_PRIV_TYPE_INT | 16,
 	 ""},
-	{
-	 WLAN_TPCCFG,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "tpccfg"},
-	{
-	 WLAN_POWERCFG,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "powercfg"},
-	{
-	 WLAN_AUTO_FREQ_SET,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "setafc"},
-	{
-	 WLAN_AUTO_FREQ_GET,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "getafc"},
-	{
-	 WLAN_SCANPROBES,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "scanprobes"},
 	{
 	 WLAN_LED_GPIO_CTRL,
 	 IW_PRIV_TYPE_INT | 16,
 	 IW_PRIV_TYPE_INT | 16,
 	 "ledgpio"},
-	{
-	 WLAN_ADAPT_RATESET,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "rateadapt"},
-	{
-	 WLAN_INACTIVITY_TIMEOUT,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "inactivityto"},
-	{
-	 WLANSNR,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "getSNR"},
-	{
-	 WLAN_GET_RATE,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "getrate"},
-	{
-	 WLAN_GET_RXINFO,
-	 IW_PRIV_TYPE_INT | 16,
-	 IW_PRIV_TYPE_INT | 16,
-	 "getrxinfo"},
 };
 
 static struct iw_statistics *wlan_get_wireless_stats(struct net_device *dev)

drivers/net/wireless/libertas/wext.h

@@ -10,88 +10,22 @@
 /** PRIVATE CMD ID */
 #define	WLANIOCTL			SIOCIWFIRSTPRIV
 
-#define WLANSETWPAIE			(WLANIOCTL + 0)
-
-#define WLAN_SETINT_GETINT		(WLANIOCTL + 7)
-#define WLANNF					1
-#define WLANRSSI				2
-#define WLANENABLE11D				5
-#define WLANADHOCGRATE				6
-#define WLAN_SUBCMD_SET_PRESCAN			11
-
 #define WLAN_SETNONE_GETNONE	        (WLANIOCTL + 8)
-#define WLANDEAUTH                  		1
-#define WLANRADIOON                 		2
-#define WLANRADIOOFF                		3
-#define WLANREMOVEADHOCAES          		4
-#define WLANADHOCSTOP               		5
-#define WLANCIPHERTEST              		6
-#define WLANCRYPTOTEST				7
-
-#define WLANWLANIDLEON				10
-#define WLANWLANIDLEOFF				11
 #define WLAN_SUBCMD_BT_RESET			13
 #define WLAN_SUBCMD_FWT_RESET			14
 
-#define WLANGETLOG                  	(WLANIOCTL + 9)
-#define GETLOG_BUFSIZE  300
-
-#define WLANSCAN_TYPE			(WLANIOCTL + 11)
-
 #define WLAN_SETNONE_GETONEINT		(WLANIOCTL + 15)
 #define WLANGETREGION				1
-#define WLAN_GET_LISTEN_INTERVAL		2
-#define WLAN_GET_MULTIPLE_DTIM			3
-#define WLAN_GET_TX_RATE			4
-#define	WLANGETBCNAVG				5
 
-#define WLAN_GET_LINKMODE			6
-#define WLAN_GET_RADIOMODE			7
-#define WLAN_GET_DEBUGMODE			8
 #define WLAN_SUBCMD_FWT_CLEANUP			15
 #define WLAN_SUBCMD_FWT_TIME			16
 #define WLAN_SUBCMD_MESH_GET_TTL		17
 
-#define WLANREGCFRDWR			(WLANIOCTL + 18)
-
-#define WLAN_SETNONE_GETTWELVE_CHAR (WLANIOCTL + 19)
-#define WLAN_SUBCMD_GETRXANTENNA    1
-#define WLAN_SUBCMD_GETTXANTENNA    2
-#define WLAN_GET_TSF                3
-
-#define WLAN_SETNONE_GETWORDCHAR	(WLANIOCTL + 21)
-#define WLANGETADHOCAES				1
-
-#define WLAN_SETONEINT_GETONEINT	(WLANIOCTL + 23)
-#define WLAN_BEACON_INTERVAL			1
-#define	WLAN_LISTENINTRVL			4
-
-#define WLAN_TXCONTROL				6
-#define WLAN_NULLPKTINTERVAL			7
-
 #define WLAN_SETONEINT_GETNONE		(WLANIOCTL + 24)
-#define WLAN_SUBCMD_SETRXANTENNA		1
-#define WLAN_SUBCMD_SETTXANTENNA		2
-#define WLANSETAUTHALG				5
-#define WLANSET8021XAUTHALG			6
-#define WLANSETENCRYPTIONMODE			7
 #define WLANSETREGION				8
-#define WLAN_SET_LISTEN_INTERVAL		9
-
-#define WLAN_SET_MULTIPLE_DTIM			10
-#define WLAN_SET_ATIM_WINDOW			11
-#define WLANSETBCNAVG				13
-#define WLANSETDATAAVG				14
-#define WLAN_SET_LINKMODE			15
-#define WLAN_SET_RADIOMODE			16
-#define WLAN_SET_DEBUGMODE			17
 #define WLAN_SUBCMD_MESH_SET_TTL		18
 
 #define WLAN_SET128CHAR_GET128CHAR	(WLANIOCTL + 25)
-#define WLANSCAN_MODE				6
-
-#define WLAN_GET_ADHOC_STATUS			9
-
 #define WLAN_SUBCMD_BT_ADD			18
 #define WLAN_SUBCMD_BT_DEL   			19
 #define WLAN_SUBCMD_BT_LIST			20
@@ -103,27 +37,8 @@
 #define WLAN_SUBCMD_FWT_LIST_ROUTE			26
 
 #define WLAN_SET_GET_SIXTEEN_INT       (WLANIOCTL + 29)
-#define WLAN_TPCCFG                             1
-#define WLAN_POWERCFG                           2
-
-#define WLAN_AUTO_FREQ_SET			3
-#define WLAN_AUTO_FREQ_GET			4
 #define WLAN_LED_GPIO_CTRL			5
-#define WLAN_SCANPROBES 			6
-#define	WLAN_ADAPT_RATESET			8
-#define	WLAN_INACTIVITY_TIMEOUT			9
-#define WLANSNR					10
-#define WLAN_GET_RATE				11
-#define	WLAN_GET_RXINFO				12
-
-#define WLANCMD52RDWR			(WLANIOCTL + 30)
-#define WLANCMD53RDWR			(WLANIOCTL + 31)
-#define CMD53BUFLEN				32
 
-#define	REG_MAC					0x19
-#define	REG_BBP					0x1a
-#define	REG_RF					0x1b
-#define	REG_EEPROM				0x59
 #define WLAN_LINKMODE_802_3			0
 #define WLAN_LINKMODE_802_11			2
 #define WLAN_RADIOMODE_NONE    			0