Merge commit 'kumar/kumar-next' into next

Documentation/powerpc/dts-bindings/fsl/board.txt

@@ -18,7 +18,7 @@ This is the memory-mapped registers for on board FPGA.
 
 Required properities:
 - compatible : should be "fsl,fpga-pixis".
-- reg : should contain the address and the lenght of the FPPGA register
+- reg : should contain the address and the length of the FPPGA register
   set.
 
 Example (MPC8610HPCD):
@@ -27,3 +27,33 @@ Example (MPC8610HPCD):
 		compatible = "fsl,fpga-pixis";
 		reg = <0xe8000000 32>;
 	};
+
+* Freescale BCSR GPIO banks
+
+Some BCSR registers act as simple GPIO controllers, each such
+register can be represented by the gpio-controller node.
+
+Required properities:
+- compatible : Should be "fsl,<board>-bcsr-gpio".
+- reg : Should contain the address and the length of the GPIO bank
+  register.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional paramters (currently unused).
+- gpio-controller : Marks the port as GPIO controller.
+
+Example:
+
+	bcsr@1,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8360mds-bcsr";
+		reg = <1 0 0x8000>;
+		ranges = <0 1 0 0x8000>;
+
+		bcsr13: gpio-controller@d {
+			#gpio-cells = <2>;
+			compatible = "fsl,mpc8360mds-bcsr-gpio";
+			reg = <0xd 1>;
+			gpio-controller;
+		};
+	};

arch/powerpc/boot/dts/mpc836x_mds.dts

@@ -69,8 +69,18 @@
 		};
 
 		bcsr@1,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
  			compatible = "fsl,mpc8360mds-bcsr";
 			reg = <1 0 0x8000>;
+			ranges = <0 1 0 0x8000>;
+
+			bcsr13: gpio-controller@d {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360mds-bcsr-gpio";
+				reg = <0xd 1>;
+				gpio-controller;
+			};
 		};
 	};
 
@@ -195,10 +205,21 @@
 		};
 
 		par_io@1400 {
+			#address-cells = <1>;
+			#size-cells = <1>;
 			reg = <0x1400 0x100>;
+			ranges = <0 0x1400 0x100>;
 			device_type = "par_io";
 			num-ports = <7>;
 
+			qe_pio_b: gpio-controller@18 {
+				#gpio-cells = <2>;
+				compatible = "fsl,mpc8360-qe-pario-bank",
+					     "fsl,mpc8323-qe-pario-bank";
+				reg = <0x18 0x18>;
+				gpio-controller;
+			};
+
 			pio1: ucc_pin@01 {
 				pio-map = <
 			/* port  pin  dir  open_drain  assignment  has_irq */
@@ -282,6 +303,15 @@
 			};
 		};
 
+		timer@440 {
+			compatible = "fsl,mpc8360-qe-gtm",
+				     "fsl,qe-gtm", "fsl,gtm";
+			reg = <0x440 0x40>;
+			clock-frequency = <132000000>;
+			interrupts = <12 13 14 15>;
+			interrupt-parent = <&qeic>;
+		};
+
 		spi@4c0 {
 			cell-index = <0>;
 			compatible = "fsl,spi";
@@ -301,11 +331,20 @@
 		};
 
 		usb@6c0 {
-			compatible = "qe_udc";
+			compatible = "fsl,mpc8360-qe-usb",
+				     "fsl,mpc8323-qe-usb";
 			reg = <0x6c0 0x40 0x8b00 0x100>;
 			interrupts = <11>;
 			interrupt-parent = <&qeic>;
-			mode = "slave";
+			fsl,fullspeed-clock = "clk21";
+			fsl,lowspeed-clock = "brg9";
+			gpios = <&qe_pio_b  2 0   /* USBOE */
+				 &qe_pio_b  3 0   /* USBTP */
+				 &qe_pio_b  8 0   /* USBTN */
+				 &qe_pio_b  9 0   /* USBRP */
+				 &qe_pio_b 11 0   /* USBRN */
+				 &bcsr13    5 0   /* SPEED */
+				 &bcsr13    4 1>; /* POWER */
 		};
 
 		enet0: ucc@2000 {

arch/powerpc/boot/dts/mpc836x_rdk.dts

@@ -218,8 +218,23 @@
 				reg = <0x440 0x40>;
 				interrupts = <12 13 14 15>;
 				interrupt-parent = <&qeic>;
-				/* filled by u-boot */
-				clock-frequency = <0>;
+				clock-frequency = <166666666>;
+			};
+
+			usb@6c0 {
+				compatible = "fsl,mpc8360-qe-usb",
+					     "fsl,mpc8323-qe-usb";
+				reg = <0x6c0 0x40 0x8b00 0x100>;
+				interrupts = <11>;
+				interrupt-parent = <&qeic>;
+				fsl,fullspeed-clock = "clk21";
+				gpios = <&qe_pio_b  2 0 /* USBOE */
+					 &qe_pio_b  3 0 /* USBTP */
+					 &qe_pio_b  8 0 /* USBTN */
+					 &qe_pio_b  9 0 /* USBRP */
+					 &qe_pio_b 11 0 /* USBRN */
+					 &qe_pio_e 20 0 /* SPEED */
+					 &qe_pio_e 21 1 /* POWER */>;
 			};
 
 			spi@4c0 {

arch/powerpc/boot/dts/mpc8641_hpcn.dts

@@ -26,7 +26,13 @@
 		serial1 = &serial1;
 		pci0 = &pci0;
 		pci1 = &pci1;
-		rapidio0 = &rapidio0;
+/*
+ * Only one of Rapid IO or PCI can be present due to HW limitations and
+ * due to the fact that the 2 now share address space in the new memory
+ * map.  The most likely case is that we have PCI, so comment out the
+ * rapidio node.  Leave it here for reference.
+ */
+		/* rapidio0 = &rapidio0; */
 	};
 
 	cpus {
@@ -62,18 +68,17 @@
 		reg = <0x00000000 0x40000000>;	// 1G at 0x0
 	};
 
-	localbus@f8005000 {
+	localbus@ffe05000 {
 		#address-cells = <2>;
 		#size-cells = <1>;
 		compatible = "fsl,mpc8641-localbus", "simple-bus";
-		reg = <0xf8005000 0x1000>;
+		reg = <0xffe05000 0x1000>;
 		interrupts = <19 2>;
 		interrupt-parent = <&mpic>;
 
-		ranges = <0 0 0xff800000 0x00800000
-			  1 0 0xfe000000 0x01000000
-			  2 0 0xf8200000 0x00100000
-			  3 0 0xf8100000 0x00100000>;
+		ranges = <0 0 0xef800000 0x00800000
+			  2 0 0xffdf8000 0x00008000
+			  3 0 0xffdf0000 0x00008000>;
 
 		flash@0,0 {
 			compatible = "cfi-flash";
@@ -103,13 +108,13 @@
 		};
 	};
 
-	soc8641@f8000000 {
+	soc8641@ffe00000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		device_type = "soc";
 		compatible = "simple-bus";
-		ranges = <0x00000000 0xf8000000 0x00100000>;
-		reg = <0xf8000000 0x00001000>;	// CCSRBAR
+		ranges = <0x00000000 0xffe00000 0x00100000>;
+		reg = <0xffe00000 0x00001000>;	// CCSRBAR
 		bus-frequency = <0>;
 
 		i2c@3000 {
@@ -340,17 +345,17 @@
 		};
 	};
 
-	pci0: pcie@f8008000 {
+	pci0: pcie@ffe08000 {
 		cell-index = <0>;
 		compatible = "fsl,mpc8641-pcie";
 		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xf8008000 0x1000>;
+		reg = <0xffe08000 0x1000>;
 		bus-range = <0x0 0xff>;
 		ranges = <0x02000000 0x0 0x80000000 0x80000000 0x0 0x20000000
-			  0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+			  0x01000000 0x0 0x00000000 0xffc00000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <24 2>;
@@ -481,7 +486,7 @@
 
 				  0x01000000 0x0 0x00000000
 				  0x01000000 0x0 0x00000000
-				  0x0 0x00100000>;
+				  0x0 0x00010000>;
 			uli1575@0 {
 				reg = <0 0 0 0 0>;
 				#size-cells = <2>;
@@ -491,7 +496,7 @@
 					  0x0 0x20000000
 					  0x01000000 0x0 0x00000000
 					  0x01000000 0x0 0x00000000
-					  0x0 0x00100000>;
+					  0x0 0x00010000>;
 				isa@1e {
 					device_type = "isa";
 					#interrupt-cells = <2>;
@@ -549,17 +554,17 @@
 
 	};
 
-	pci1: pcie@f8009000 {
+	pci1: pcie@ffe09000 {
 		cell-index = <1>;
 		compatible = "fsl,mpc8641-pcie";
 		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
-		reg = <0xf8009000 0x1000>;
+		reg = <0xffe09000 0x1000>;
 		bus-range = <0 0xff>;
 		ranges = <0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000
-			  0x01000000 0x0 0x00000000 0xe3000000 0x0 0x00100000>;
+			  0x01000000 0x0 0x00000000 0xffc10000 0x0 0x00010000>;
 		clock-frequency = <33333333>;
 		interrupt-parent = <&mpic>;
 		interrupts = <25 2>;
@@ -582,18 +587,21 @@
 
 				  0x01000000 0x0 0x00000000
 				  0x01000000 0x0 0x00000000
-				  0x0 0x00100000>;
+				  0x0 0x00010000>;
 		};
 	};
-	rapidio0: rapidio@f80c0000 {
+/*
+	rapidio0: rapidio@ffec0000 {
 		#address-cells = <2>;
 		#size-cells = <2>;
 		compatible = "fsl,rapidio-delta";
-		reg = <0xf80c0000 0x20000>;
-		ranges = <0 0 0xc0000000 0 0x20000000>;
+		reg = <0xffec0000 0x20000>;
+		ranges = <0 0 0x80000000 0 0x20000000>;
 		interrupt-parent = <&mpic>;
-		/* err_irq bell_outb_irq bell_inb_irq
-			msg1_tx_irq msg1_rx_irq	msg2_tx_irq msg2_rx_irq */
+		// err_irq bell_outb_irq bell_inb_irq
+		//	msg1_tx_irq msg1_rx_irq	msg2_tx_irq msg2_rx_irq
 		interrupts = <48 2 49 2 50 2 53 2 54 2 55 2 56 2>;
 	};
+*/
+
 };

arch/powerpc/configs/85xx/mpc8572_ds_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc3
-# Sat Nov  8 12:40:13 2008
+# Linux kernel version: 2.6.28-rc8
+# Tue Dec 30 11:17:46 2008
 #
 # CONFIG_PPC64 is not set
 
@@ -21,7 +21,10 @@ CONFIG_FSL_BOOKE=y
 CONFIG_FSL_EMB_PERFMON=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_SPE=y
+CONFIG_PPC_MMU_NOHASH=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_SMP=y
+CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
 # CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
@@ -50,7 +53,7 @@ CONFIG_ARCH_MAY_HAVE_PC_FDC=y
 CONFIG_PPC_OF=y
 CONFIG_OF=y
 CONFIG_PPC_UDBG_16550=y
-# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
 CONFIG_DEFAULT_UIMAGE=y
@@ -62,7 +65,7 @@ CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
 # General setup
 #
 CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
 CONFIG_INIT_ENV_ARG_LIMIT=32
 CONFIG_LOCALVERSION=""
 CONFIG_LOCALVERSION_AUTO=y
@@ -126,6 +129,7 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_USE_GENERIC_SMP_HELPERS=y
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
@@ -138,6 +142,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_KMOD=y
+CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
 CONFIG_LBD=y
 # CONFIG_BLK_DEV_IO_TRACE is not set
@@ -197,6 +202,7 @@ CONFIG_PPC_I8259=y
 # CONFIG_CPM2 is not set
 CONFIG_FSL_ULI1575=y
 # CONFIG_MPC8xxx_GPIO is not set
+# CONFIG_SIMPLE_GPIO is not set
 
 #
 # Kernel options
@@ -224,6 +230,7 @@ CONFIG_MATH_EMULATION=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
+# CONFIG_IRQ_ALL_CPUS is not set
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_ARCH_POPULATES_NODE_MAP=y
 CONFIG_SELECT_MEMORY_MODEL=y
@@ -241,6 +248,9 @@ CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
 CONFIG_UNEVICTABLE_LRU=y
+CONFIG_PPC_4K_PAGES=y
+# CONFIG_PPC_16K_PAGES is not set
+# CONFIG_PPC_64K_PAGES is not set
 CONFIG_FORCE_MAX_ZONEORDER=11
 CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
@@ -443,8 +453,10 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_93CX6 is not set
 # CONFIG_SGI_IOC4 is not set
 # CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
 # CONFIG_HP_ILO is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -784,6 +796,7 @@ CONFIG_SERIAL_CORE_CONSOLE=y
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_HVC_UDBG is not set
 # CONFIG_IPMI_HANDLER is not set
 CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
@@ -869,11 +882,11 @@ CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_THERMAL is not set
 # CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
 
 #
 # Sonics Silicon Backplane
 #
-CONFIG_SSB_POSSIBLE=y
 # CONFIG_SSB is not set
 
 #
@@ -886,14 +899,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
-
-#
-# Voltage and Current regulators
-#
 # CONFIG_REGULATOR is not set
-# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
-# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
-# CONFIG_REGULATOR_BQ24022 is not set
 
 #
 # Multimedia devices
@@ -1252,11 +1258,11 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
 # CONFIG_USB_TMC is not set
 
 #
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
 #
 
 #
-# may also be needed; see USB_STORAGE Help for more information
+# see USB_STORAGE Help for more information
 #
 CONFIG_USB_STORAGE=y
 # CONFIG_USB_STORAGE_DEBUG is not set
@@ -1348,6 +1354,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
 
 #
 # SPI RTC drivers
@@ -1624,6 +1631,7 @@ CONFIG_HAVE_FUNCTION_TRACER=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_DEBUG_PAGEALLOC is not set
@@ -1649,11 +1657,16 @@ CONFIG_CRYPTO=y
 #
 # CONFIG_CRYPTO_FIPS is not set
 CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
 CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
 CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
 CONFIG_CRYPTO_HASH=y
-CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
 CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
 # CONFIG_CRYPTO_GF128MUL is not set
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_CRYPTD is not set

arch/powerpc/include/asm/qe.h

@@ -17,6 +17,8 @@
 #ifdef __KERNEL__
 
 #include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/err.h>
 #include <asm/cpm.h>
 #include <asm/immap_qe.h>
 
@@ -84,7 +86,11 @@ static inline bool qe_clock_is_brg(enum qe_clock clk)
 extern spinlock_t cmxgcr_lock;
 
 /* Export QE common operations */
+#ifdef CONFIG_QUICC_ENGINE
 extern void __init qe_reset(void);
+#else
+static inline void qe_reset(void) {}
+#endif
 
 /* QE PIO */
 #define QE_PIO_PINS 32
@@ -101,16 +107,43 @@ struct qe_pio_regs {
 #endif
 };
 
-extern int par_io_init(struct device_node *np);
-extern int par_io_of_config(struct device_node *np);
 #define QE_PIO_DIR_IN	2
 #define QE_PIO_DIR_OUT	1
 extern void __par_io_config_pin(struct qe_pio_regs __iomem *par_io, u8 pin,
 				int dir, int open_drain, int assignment,
 				int has_irq);
+#ifdef CONFIG_QUICC_ENGINE
+extern int par_io_init(struct device_node *np);
+extern int par_io_of_config(struct device_node *np);
 extern int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
 			     int assignment, int has_irq);
 extern int par_io_data_set(u8 port, u8 pin, u8 val);
+#else
+static inline int par_io_init(struct device_node *np) { return -ENOSYS; }
+static inline int par_io_of_config(struct device_node *np) { return -ENOSYS; }
+static inline int par_io_config_pin(u8 port, u8 pin, int dir, int open_drain,
+		int assignment, int has_irq) { return -ENOSYS; }
+static inline int par_io_data_set(u8 port, u8 pin, u8 val) { return -ENOSYS; }
+#endif /* CONFIG_QUICC_ENGINE */
+
+/*
+ * Pin multiplexing functions.
+ */
+struct qe_pin;
+#ifdef CONFIG_QE_GPIO
+extern struct qe_pin *qe_pin_request(struct device_node *np, int index);
+extern void qe_pin_free(struct qe_pin *qe_pin);
+extern void qe_pin_set_gpio(struct qe_pin *qe_pin);
+extern void qe_pin_set_dedicated(struct qe_pin *pin);
+#else
+static inline struct qe_pin *qe_pin_request(struct device_node *np, int index)
+{
+	return ERR_PTR(-ENOSYS);
+}
+static inline void qe_pin_free(struct qe_pin *qe_pin) {}
+static inline void qe_pin_set_gpio(struct qe_pin *qe_pin) {}
+static inline void qe_pin_set_dedicated(struct qe_pin *pin) {}
+#endif /* CONFIG_QE_GPIO */
 
 /* QE internal API */
 int qe_issue_cmd(u32 cmd, u32 device, u8 mcn_protocol, u32 cmd_input);

arch/powerpc/include/asm/qe_ic.h

@@ -17,6 +17,9 @@
 
 #include <linux/irq.h>
 
+struct device_node;
+struct qe_ic;
+
 #define NUM_OF_QE_IC_GROUPS	6
 
 /* Flags when we init the QE IC */
@@ -54,17 +57,27 @@ enum qe_ic_grp_id {
 	QE_IC_GRP_RISCB		/* QE interrupt controller RISC group B */
 };
 
+#ifdef CONFIG_QUICC_ENGINE
 void qe_ic_init(struct device_node *node, unsigned int flags,
 		void (*low_handler)(unsigned int irq, struct irq_desc *desc),
 		void (*high_handler)(unsigned int irq, struct irq_desc *desc));
+unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
+unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
+#else
+static inline void qe_ic_init(struct device_node *node, unsigned int flags,
+		void (*low_handler)(unsigned int irq, struct irq_desc *desc),
+		void (*high_handler)(unsigned int irq, struct irq_desc *desc))
+{}
+static inline unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic)
+{ return 0; }
+static inline unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic)
+{ return 0; }
+#endif /* CONFIG_QUICC_ENGINE */
+
 void qe_ic_set_highest_priority(unsigned int virq, int high);
 int qe_ic_set_priority(unsigned int virq, unsigned int priority);
 int qe_ic_set_high_priority(unsigned int virq, unsigned int priority, int high);
 
-struct qe_ic;
-unsigned int qe_ic_get_low_irq(struct qe_ic *qe_ic);
-unsigned int qe_ic_get_high_irq(struct qe_ic *qe_ic);
-
 static inline void qe_ic_cascade_low_ipic(unsigned int irq,
 					  struct irq_desc *desc)
 {

arch/powerpc/platforms/83xx/mpc831x_rdb.c

@@ -42,7 +42,7 @@ static void __init mpc831x_rdb_setup_arch(void)
 	mpc831x_usb_cfg();
 }
 
-void __init mpc831x_rdb_init_IRQ(void)
+static void __init mpc831x_rdb_init_IRQ(void)
 {
 	struct device_node *np;
 

arch/powerpc/platforms/83xx/mpc832x_mds.c

@@ -49,8 +49,6 @@
 #define DBG(fmt...)
 #endif
 
-static u8 *bcsr_regs = NULL;
-
 /* ************************************************************************
  *
  * Setup the architecture
@@ -59,13 +57,14 @@ static u8 *bcsr_regs = NULL;
 static void __init mpc832x_sys_setup_arch(void)
 {
 	struct device_node *np;
+	u8 __iomem *bcsr_regs = NULL;
 
 	if (ppc_md.progress)
 		ppc_md.progress("mpc832x_sys_setup_arch()", 0);
 
 	/* Map BCSR area */
 	np = of_find_node_by_name(NULL, "bcsr");
-	if (np != 0) {
+	if (np) {
 		struct resource res;
 
 		of_address_to_resource(np, 0, &res);
@@ -93,9 +92,9 @@ static void __init mpc832x_sys_setup_arch(void)
 			!= NULL){
 		/* Reset the Ethernet PHYs */
 #define BCSR8_FETH_RST 0x50
-		bcsr_regs[8] &= ~BCSR8_FETH_RST;
+		clrbits8(&bcsr_regs[8], BCSR8_FETH_RST);
 		udelay(1000);
-		bcsr_regs[8] |= BCSR8_FETH_RST;
+		setbits8(&bcsr_regs[8], BCSR8_FETH_RST);
 		iounmap(bcsr_regs);
 		of_node_put(np);
 	}

arch/powerpc/platforms/83xx/mpc832x_rdb.c

@@ -38,6 +38,7 @@
 #define DBG(fmt...)
 #endif
 
+#ifdef CONFIG_QUICC_ENGINE
 static void mpc83xx_spi_activate_cs(u8 cs, u8 polarity)
 {
 	pr_debug("%s %d %d\n", __func__, cs, polarity);
@@ -77,8 +78,8 @@ static int __init mpc832x_spi_init(void)
 			    mpc83xx_spi_activate_cs,
 			    mpc83xx_spi_deactivate_cs);
 }
-
 machine_device_initcall(mpc832x_rdb, mpc832x_spi_init);
+#endif /* CONFIG_QUICC_ENGINE */
 
 /* ************************************************************************
  *
@@ -130,7 +131,7 @@ static int __init mpc832x_declare_of_platform_devices(void)
 }
 machine_device_initcall(mpc832x_rdb, mpc832x_declare_of_platform_devices);
 
-void __init mpc832x_rdb_init_IRQ(void)
+static void __init mpc832x_rdb_init_IRQ(void)
 {
 
 	struct device_node *np;

arch/powerpc/platforms/83xx/mpc836x_mds.c

@@ -18,6 +18,7 @@
 
 #include <linux/stddef.h>
 #include <linux/kernel.h>
+#include <linux/compiler.h>
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/reboot.h>
@@ -43,6 +44,7 @@
 #include <asm/udbg.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
+#include <sysdev/simple_gpio.h>
 #include <asm/qe.h>
 #include <asm/qe_ic.h>
 
@@ -55,8 +57,6 @@
 #define DBG(fmt...)
 #endif
 
-static u8 *bcsr_regs = NULL;
-
 /* ************************************************************************
  *
  * Setup the architecture
@@ -65,13 +65,14 @@ static u8 *bcsr_regs = NULL;
 static void __init mpc836x_mds_setup_arch(void)
 {
 	struct device_node *np;
+	u8 __iomem *bcsr_regs = NULL;
 
 	if (ppc_md.progress)
 		ppc_md.progress("mpc836x_mds_setup_arch()", 0);
 
 	/* Map BCSR area */
 	np = of_find_node_by_name(NULL, "bcsr");
-	if (np != 0) {
+	if (np) {
 		struct resource res;
 
 		of_address_to_resource(np, 0, &res);
@@ -93,6 +94,16 @@ static void __init mpc836x_mds_setup_arch(void)
 
 		for (np = NULL; (np = of_find_node_by_name(np, "ucc")) != NULL;)
 			par_io_of_config(np);
+#ifdef CONFIG_QE_USB
+		/* Must fixup Par IO before QE GPIO chips are registered. */
+		par_io_config_pin(1,  2, 1, 0, 3, 0); /* USBOE  */
+		par_io_config_pin(1,  3, 1, 0, 3, 0); /* USBTP  */
+		par_io_config_pin(1,  8, 1, 0, 1, 0); /* USBTN  */
+		par_io_config_pin(1, 10, 2, 0, 3, 0); /* USBRXD */
+		par_io_config_pin(1,  9, 2, 1, 3, 0); /* USBRP  */
+		par_io_config_pin(1, 11, 2, 1, 3, 0); /* USBRN  */
+		par_io_config_pin(2, 20, 2, 0, 1, 0); /* CLK21  */
+#endif /* CONFIG_QE_USB */
 	}
 
 	if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
@@ -151,6 +162,70 @@ static int __init mpc836x_declare_of_platform_devices(void)
 }
 machine_device_initcall(mpc836x_mds, mpc836x_declare_of_platform_devices);
 
+#ifdef CONFIG_QE_USB
+static int __init mpc836x_usb_cfg(void)
+{
+	u8 __iomem *bcsr;
+	struct device_node *np;
+	const char *mode;
+	int ret = 0;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,mpc8360mds-bcsr");
+	if (!np)
+		return -ENODEV;
+
+	bcsr = of_iomap(np, 0);
+	of_node_put(np);
+	if (!bcsr)
+		return -ENOMEM;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,mpc8323-qe-usb");
+	if (!np) {
+		ret = -ENODEV;
+		goto err;
+	}
+
+#define BCSR8_TSEC1M_MASK	(0x3 << 6)
+#define BCSR8_TSEC1M_RGMII	(0x0 << 6)
+#define BCSR8_TSEC2M_MASK	(0x3 << 4)
+#define BCSR8_TSEC2M_RGMII	(0x0 << 4)
+	/*
+	 * Default is GMII (2), but we should set it to RGMII (0) if we use
+	 * USB (Eth PHY is in RGMII mode anyway).
+	 */
+	clrsetbits_8(&bcsr[8], BCSR8_TSEC1M_MASK | BCSR8_TSEC2M_MASK,
+			       BCSR8_TSEC1M_RGMII | BCSR8_TSEC2M_RGMII);
+
+#define BCSR13_USBMASK	0x0f
+#define BCSR13_nUSBEN	0x08 /* 1 - Disable, 0 - Enable			*/
+#define BCSR13_USBSPEED	0x04 /* 1 - Full, 0 - Low			*/
+#define BCSR13_USBMODE	0x02 /* 1 - Host, 0 - Function			*/
+#define BCSR13_nUSBVCC	0x01 /* 1 - gets VBUS, 0 - supplies VBUS 	*/
+
+	clrsetbits_8(&bcsr[13], BCSR13_USBMASK, BCSR13_USBSPEED);
+
+	mode = of_get_property(np, "mode", NULL);
+	if (mode && !strcmp(mode, "peripheral")) {
+		setbits8(&bcsr[13], BCSR13_nUSBVCC);
+		qe_usb_clock_set(QE_CLK21, 48000000);
+	} else {
+		setbits8(&bcsr[13], BCSR13_USBMODE);
+		/*
+		 * The BCSR GPIOs are used to control power and
+		 * speed of the USB transceiver. This is needed for
+		 * the USB Host only.
+		 */
+		simple_gpiochip_init("fsl,mpc8360mds-bcsr-gpio");
+	}
+
+	of_node_put(np);
+err:
+	iounmap(bcsr);
+	return ret;
+}
+machine_arch_initcall(mpc836x_mds, mpc836x_usb_cfg);
+#endif /* CONFIG_QE_USB */
+
 static void __init mpc836x_mds_init_IRQ(void)
 {
 	struct device_node *np;

arch/powerpc/platforms/83xx/mpc836x_rdk.c

@@ -51,8 +51,9 @@ static void __init mpc836x_rdk_setup_arch(void)
 	for_each_compatible_node(np, "pci", "fsl,mpc8349-pci")
 		mpc83xx_add_bridge(np);
 #endif
-
+#ifdef CONFIG_QUICC_ENGINE
 	qe_reset();
+#endif
 }
 
 static void __init mpc836x_rdk_init_IRQ(void)
@@ -71,13 +72,14 @@ static void __init mpc836x_rdk_init_IRQ(void)
 	 */
 	ipic_set_default_priority();
 	of_node_put(np);
-
+#ifdef CONFIG_QUICC_ENGINE
 	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
 	if (!np)
 		return;
 
 	qe_ic_init(np, 0, qe_ic_cascade_low_ipic, qe_ic_cascade_high_ipic);
 	of_node_put(np);
+#endif
 }
 
 /*

arch/powerpc/platforms/83xx/mpc837x_mds.c

@@ -26,7 +26,6 @@
 #define BCSR12_USB_SER_MASK	0x8a
 #define BCSR12_USB_SER_PIN	0x80
 #define BCSR12_USB_SER_DEVICE	0x02
-extern int mpc837x_usb_cfg(void);
 
 static int mpc837xmds_usb_cfg(void)
 {

arch/powerpc/platforms/83xx/mpc837x_rdb.c

@@ -21,8 +21,6 @@
 
 #include "mpc83xx.h"
 
-extern int mpc837x_usb_cfg(void);
-
 /* ************************************************************************
  *
  * Setup the architecture

arch/powerpc/platforms/83xx/mpc83xx.h

@@ -61,6 +61,7 @@
 
 extern void mpc83xx_restart(char *cmd);
 extern long mpc83xx_time_init(void);
+extern int mpc837x_usb_cfg(void);
 extern int mpc834x_usb_cfg(void);
 extern int mpc831x_usb_cfg(void);
 

arch/powerpc/platforms/85xx/mpc85xx_ds.c

@@ -148,6 +148,9 @@ static int mpc85xx_exclude_device(struct pci_controller *hose,
 /*
  * Setup the architecture
  */
+#ifdef CONFIG_SMP
+extern void __init mpc85xx_smp_init(void);
+#endif
 static void __init mpc85xx_ds_setup_arch(void)
 {
 #ifdef CONFIG_PCI
@@ -173,6 +176,10 @@ static void __init mpc85xx_ds_setup_arch(void)
 	ppc_md.pci_exclude_device = mpc85xx_exclude_device;
 #endif
 
+#ifdef CONFIG_SMP
+	mpc85xx_smp_init();
+#endif
+
 	printk("MPC85xx DS board from Freescale Semiconductor\n");
 }
 

arch/powerpc/platforms/85xx/smp.c

@@ -58,6 +58,7 @@ smp_85xx_kick_cpu(int nr)
 
 	if (cpu_rel_addr == NULL) {
 		printk(KERN_ERR "No cpu-release-addr for cpu %d\n", nr);
+		local_irq_restore(flags);
 		return;
 	}
 

arch/powerpc/platforms/Kconfig

@@ -312,4 +312,15 @@ config MPC8xxx_GPIO
 	  Say Y here if you're going to use hardware that connects to the
 	  MPC831x/834x/837x/8572/8610 GPIOs.
 
+config SIMPLE_GPIO
+	bool "Support for simple, memory-mapped GPIO controllers"
+	depends on PPC
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	  Say Y here to support simple, memory-mapped GPIO controllers.
+	  These are usually BCSRs used to control board's switches, LEDs,
+	  chip-selects, Ethernet/USB PHY's power and various other small
+	  on-board peripherals.
+
 endmenu

arch/powerpc/platforms/Kconfig.cputype

@@ -231,7 +231,7 @@ config VIRT_CPU_ACCOUNTING
 	  If in doubt, say Y here.
 
 config SMP
-	depends on PPC_STD_MMU
+	depends on PPC_STD_MMU || FSL_BOOKE
 	bool "Symmetric multi-processing support"
 	---help---
 	  This enables support for systems with more than one CPU. If you have

arch/powerpc/sysdev/Makefile

@@ -17,6 +17,7 @@ obj-$(CONFIG_FSL_PCI)		+= fsl_pci.o $(fsl-msi-obj-y)
 obj-$(CONFIG_FSL_LBC)		+= fsl_lbc.o
 obj-$(CONFIG_FSL_GTM)		+= fsl_gtm.o
 obj-$(CONFIG_MPC8xxx_GPIO)	+= mpc8xxx_gpio.o
+obj-$(CONFIG_SIMPLE_GPIO)	+= simple_gpio.o
 obj-$(CONFIG_RAPIDIO)		+= fsl_rio.o
 obj-$(CONFIG_TSI108_BRIDGE)	+= tsi108_pci.o tsi108_dev.o
 obj-$(CONFIG_QUICC_ENGINE)	+= qe_lib/

arch/powerpc/sysdev/fsl_pci.c

@@ -29,7 +29,8 @@
 
 #if defined(CONFIG_PPC_85xx) || defined(CONFIG_PPC_86xx)
 /* atmu setup for fsl pci/pcie controller */
-void __init setup_pci_atmu(struct pci_controller *hose, struct resource *rsrc)
+static void __init setup_pci_atmu(struct pci_controller *hose,
+				  struct resource *rsrc)
 {
 	struct ccsr_pci __iomem *pci;
 	int i;
@@ -86,7 +87,7 @@ void __init setup_pci_atmu(struct pci_controller *hose, struct resource *rsrc)
 	out_be32(&pci->piw[2].piwar, PIWAR_2G);
 }
 
-void __init setup_pci_cmd(struct pci_controller *hose)
+static void __init setup_pci_cmd(struct pci_controller *hose)
 {
 	u16 cmd;
 	int cap_x;
@@ -130,7 +131,7 @@ static void __init quirk_fsl_pcie_header(struct pci_dev *dev)
 	return ;
 }
 
-int __init fsl_pcie_check_link(struct pci_controller *hose)
+static int __init fsl_pcie_check_link(struct pci_controller *hose)
 {
 	u32 val;
 	early_read_config_dword(hose, 0, 0, PCIE_LTSSM, &val);

arch/powerpc/sysdev/fsl_soc.h

@@ -5,8 +5,13 @@
 #include <asm/mmu.h>
 
 extern phys_addr_t get_immrbase(void);
+#if defined(CONFIG_CPM2) || defined(CONFIG_QUICC_ENGINE) || defined(CONFIG_8xx)
 extern u32 get_brgfreq(void);
 extern u32 get_baudrate(void);
+#else
+static inline u32 get_brgfreq(void) { return -1; }
+static inline u32 get_baudrate(void) { return -1; }
+#endif
 extern u32 fsl_get_sys_freq(void);
 
 struct spi_board_info;

arch/powerpc/sysdev/qe_lib/Kconfig

@@ -22,5 +22,6 @@ config UCC
 
 config QE_USB
 	bool
+	default y if USB_GADGET_FSL_QE
 	help
-	  QE USB Host Controller support
+	  QE USB Controller support

arch/powerpc/sysdev/qe_lib/gpio.c

@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/spinlock.h>
+#include <linux/err.h>
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
@@ -24,8 +25,14 @@ struct qe_gpio_chip {
 	struct of_mm_gpio_chip mm_gc;
 	spinlock_t lock;
 
+	unsigned long pin_flags[QE_PIO_PINS];
+#define QE_PIN_REQUESTED 0
+
 	/* shadowed data register to clear/set bits safely */
 	u32 cpdata;
+
+	/* saved_regs used to restore dedicated functions */
+	struct qe_pio_regs saved_regs;
 };
 
 static inline struct qe_gpio_chip *
@@ -40,6 +47,12 @@ static void qe_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
 	struct qe_pio_regs __iomem *regs = mm_gc->regs;
 
 	qe_gc->cpdata = in_be32(&regs->cpdata);
+	qe_gc->saved_regs.cpdata = qe_gc->cpdata;
+	qe_gc->saved_regs.cpdir1 = in_be32(&regs->cpdir1);
+	qe_gc->saved_regs.cpdir2 = in_be32(&regs->cpdir2);
+	qe_gc->saved_regs.cppar1 = in_be32(&regs->cppar1);
+	qe_gc->saved_regs.cppar2 = in_be32(&regs->cppar2);
+	qe_gc->saved_regs.cpodr = in_be32(&regs->cpodr);
 }
 
 static int qe_gpio_get(struct gpio_chip *gc, unsigned int gpio)
@@ -103,6 +116,188 @@ static int qe_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
 	return 0;
 }
 
+struct qe_pin {
+	/*
+	 * The qe_gpio_chip name is unfortunate, we should change that to
+	 * something like qe_pio_controller. Someday.
+	 */
+	struct qe_gpio_chip *controller;
+	int num;
+};
+
+/**
+ * qe_pin_request - Request a QE pin
+ * @np:		device node to get a pin from
+ * @index:	index of a pin in the device tree
+ * Context:	non-atomic
+ *
+ * This function return qe_pin so that you could use it with the rest of
+ * the QE Pin Multiplexing API.
+ */
+struct qe_pin *qe_pin_request(struct device_node *np, int index)
+{
+	struct qe_pin *qe_pin;
+	struct device_node *gc;
+	struct of_gpio_chip *of_gc = NULL;
+	struct of_mm_gpio_chip *mm_gc;
+	struct qe_gpio_chip *qe_gc;
+	int err;
+	int size;
+	const void *gpio_spec;
+	const u32 *gpio_cells;
+	unsigned long flags;
+
+	qe_pin = kzalloc(sizeof(*qe_pin), GFP_KERNEL);
+	if (!qe_pin) {
+		pr_debug("%s: can't allocate memory\n", __func__);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	err = of_parse_phandles_with_args(np, "gpios", "#gpio-cells", index,
+					  &gc, &gpio_spec);
+	if (err) {
+		pr_debug("%s: can't parse gpios property\n", __func__);
+		goto err0;
+	}
+
+	if (!of_device_is_compatible(gc, "fsl,mpc8323-qe-pario-bank")) {
+		pr_debug("%s: tried to get a non-qe pin\n", __func__);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	of_gc = gc->data;
+	if (!of_gc) {
+		pr_debug("%s: gpio controller %s isn't registered\n",
+			 np->full_name, gc->full_name);
+		err = -ENODEV;
+		goto err1;
+	}
+
+	gpio_cells = of_get_property(gc, "#gpio-cells", &size);
+	if (!gpio_cells || size != sizeof(*gpio_cells) ||
+			*gpio_cells != of_gc->gpio_cells) {
+		pr_debug("%s: wrong #gpio-cells for %s\n",
+			 np->full_name, gc->full_name);
+		err = -EINVAL;
+		goto err1;
+	}
+
+	err = of_gc->xlate(of_gc, np, gpio_spec, NULL);
+	if (err < 0)
+		goto err1;
+
+	mm_gc = to_of_mm_gpio_chip(&of_gc->gc);
+	qe_gc = to_qe_gpio_chip(mm_gc);
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (test_and_set_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[err]) == 0) {
+		qe_pin->controller = qe_gc;
+		qe_pin->num = err;
+		err = 0;
+	} else {
+		err = -EBUSY;
+	}
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	if (!err)
+		return qe_pin;
+err1:
+	of_node_put(gc);
+err0:
+	kfree(qe_pin);
+	pr_debug("%s failed with status %d\n", __func__, err);
+	return ERR_PTR(err);
+}
+EXPORT_SYMBOL(qe_pin_request);
+
+/**
+ * qe_pin_free - Free a pin
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function frees the qe_pin structure and makes a pin available
+ * for further qe_pin_request() calls.
+ */
+void qe_pin_free(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	unsigned long flags;
+	const int pin = qe_pin->num;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+	test_and_clear_bit(QE_PIN_REQUESTED, &qe_gc->pin_flags[pin]);
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+
+	kfree(qe_pin);
+}
+EXPORT_SYMBOL(qe_pin_free);
+
+/**
+ * qe_pin_set_dedicated - Revert a pin to a dedicated peripheral function mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function resets a pin to a dedicated peripheral function that
+ * has been set up by the firmware.
+ */
+void qe_pin_set_dedicated(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	struct qe_pio_regs *sregs = &qe_gc->saved_regs;
+	int pin = qe_pin->num;
+	u32 mask1 = 1 << (QE_PIO_PINS - (pin + 1));
+	u32 mask2 = 0x3 << (QE_PIO_PINS - (pin % (QE_PIO_PINS / 2) + 1) * 2);
+	bool second_reg = pin > (QE_PIO_PINS / 2) - 1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	if (second_reg) {
+		clrsetbits_be32(&regs->cpdir2, mask2, sregs->cpdir2 & mask2);
+		clrsetbits_be32(&regs->cppar2, mask2, sregs->cppar2 & mask2);
+	} else {
+		clrsetbits_be32(&regs->cpdir1, mask2, sregs->cpdir1 & mask2);
+		clrsetbits_be32(&regs->cppar1, mask2, sregs->cppar1 & mask2);
+	}
+
+	if (sregs->cpdata & mask1)
+		qe_gc->cpdata |= mask1;
+	else
+		qe_gc->cpdata &= ~mask1;
+
+	out_be32(&regs->cpdata, qe_gc->cpdata);
+	clrsetbits_be32(&regs->cpodr, mask1, sregs->cpodr & mask1);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_dedicated);
+
+/**
+ * qe_pin_set_gpio - Set a pin to the GPIO mode
+ * @qe_pin:	pointer to the qe_pin structure
+ * Context:	any
+ *
+ * This function sets a pin to the GPIO mode.
+ */
+void qe_pin_set_gpio(struct qe_pin *qe_pin)
+{
+	struct qe_gpio_chip *qe_gc = qe_pin->controller;
+	struct qe_pio_regs __iomem *regs = qe_gc->mm_gc.regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&qe_gc->lock, flags);
+
+	/* Let's make it input by default, GPIO API is able to change that. */
+	__par_io_config_pin(regs, qe_pin->num, QE_PIO_DIR_IN, 0, 0, 0);
+
+	spin_unlock_irqrestore(&qe_gc->lock, flags);
+}
+EXPORT_SYMBOL(qe_pin_set_gpio);
+
 static int __init qe_add_gpiochips(void)
 {
 	struct device_node *np;

arch/powerpc/sysdev/simple_gpio.c

@@ -0,0 +1,155 @@
+/*
+ * Simple Memory-Mapped GPIOs
+ *
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *
+ * Author: Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <asm/prom.h>
+#include "simple_gpio.h"
+
+struct u8_gpio_chip {
+	struct of_mm_gpio_chip mm_gc;
+	spinlock_t lock;
+
+	/* shadowed data register to clear/set bits safely */
+	u8 data;
+};
+
+static struct u8_gpio_chip *to_u8_gpio_chip(struct of_mm_gpio_chip *mm_gc)
+{
+	return container_of(mm_gc, struct u8_gpio_chip, mm_gc);
+}
+
+static u8 u8_pin2mask(unsigned int pin)
+{
+	return 1 << (8 - 1 - pin);
+}
+
+static int u8_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+
+	return in_8(mm_gc->regs) & u8_pin2mask(gpio);
+}
+
+static void u8_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+	unsigned long flags;
+
+	spin_lock_irqsave(&u8_gc->lock, flags);
+
+	if (val)
+		u8_gc->data |= u8_pin2mask(gpio);
+	else
+		u8_gc->data &= ~u8_pin2mask(gpio);
+
+	out_8(mm_gc->regs, u8_gc->data);
+
+	spin_unlock_irqrestore(&u8_gc->lock, flags);
+}
+
+static int u8_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	return 0;
+}
+
+static int u8_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	u8_gpio_set(gc, gpio, val);
+	return 0;
+}
+
+static void u8_gpio_save_regs(struct of_mm_gpio_chip *mm_gc)
+{
+	struct u8_gpio_chip *u8_gc = to_u8_gpio_chip(mm_gc);
+
+	u8_gc->data = in_8(mm_gc->regs);
+}
+
+static int __init u8_simple_gpiochip_add(struct device_node *np)
+{
+	int ret;
+	struct u8_gpio_chip *u8_gc;
+	struct of_mm_gpio_chip *mm_gc;
+	struct of_gpio_chip *of_gc;
+	struct gpio_chip *gc;
+
+	u8_gc = kzalloc(sizeof(*u8_gc), GFP_KERNEL);
+	if (!u8_gc)
+		return -ENOMEM;
+
+	spin_lock_init(&u8_gc->lock);
+
+	mm_gc = &u8_gc->mm_gc;
+	of_gc = &mm_gc->of_gc;
+	gc = &of_gc->gc;
+
+	mm_gc->save_regs = u8_gpio_save_regs;
+	of_gc->gpio_cells = 2;
+	gc->ngpio = 8;
+	gc->direction_input = u8_gpio_dir_in;
+	gc->direction_output = u8_gpio_dir_out;
+	gc->get = u8_gpio_get;
+	gc->set = u8_gpio_set;
+
+	ret = of_mm_gpiochip_add(np, mm_gc);
+	if (ret)
+		goto err;
+	return 0;
+err:
+	kfree(u8_gc);
+	return ret;
+}
+
+void __init simple_gpiochip_init(const char *compatible)
+{
+	struct device_node *np;
+
+	for_each_compatible_node(np, NULL, compatible) {
+		int ret;
+		struct resource r;
+
+		ret = of_address_to_resource(np, 0, &r);
+		if (ret)
+			goto err;
+
+		switch (resource_size(&r)) {
+		case 1:
+			ret = u8_simple_gpiochip_add(np);
+			if (ret)
+				goto err;
+			break;
+		default:
+			/*
+			 * Whenever you need support for GPIO bank width > 1,
+			 * please just turn u8_ code into huge macros, and
+			 * construct needed uX_ code with it.
+			 */
+			ret = -ENOSYS;
+			goto err;
+		}
+		continue;
+err:
+		pr_err("%s: registration failed, status %d\n",
+		       np->full_name, ret);
+	}
+}

arch/powerpc/sysdev/simple_gpio.h

@@ -0,0 +1,12 @@
+#ifndef __SYSDEV_SIMPLE_GPIO_H
+#define __SYSDEV_SIMPLE_GPIO_H
+
+#include <linux/errno.h>
+
+#ifdef CONFIG_SIMPLE_GPIO
+extern void simple_gpiochip_init(const char *compatible);
+#else
+static inline void simple_gpiochip_init(const char *compatible) {}
+#endif /* CONFIG_SIMPLE_GPIO */
+
+#endif /* __SYSDEV_SIMPLE_GPIO_H */