Merge tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a bunch of USB fixes for your 3.8-rc3 tree.  They all either
  fix problems that have been reported (like the xhci/hub changes) or
  add new device ids to existing drivers.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
  usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
  usb: host: ohci-tmio: fix compile warning
  USB: Add device quirk for Microsoft VX700 webcam
  USB: ehci-fsl: fix regression on mpc5121e
  usb: chipidea: Allow disabling streaming not only in udc mode
  USB: fsl-mph-dr-of: fix regression on mpc5121e
  USB: select USB_ARCH_HAS_EHCI for MXS
  USB: hub: handle claim of enabled remote wakeup after reset
  USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
  USB: option: add Nexpring NP10T terminal id
  USB: option: add Telekom Speedstick LTE II
  USB: option: blacklist network interface on ZTE MF880
  usb: imx21-hcd: Include missing linux/module.h
  USB: option: Add new MEDIATEK PID support
  USB: ehci: make debug port in-use detection functional again
  USB: usbtest: fix test number in log message
  xhci: Avoid "dead ports", add roothub port polling.
  USB: Handle warm reset failure on empty port.
  USB: Ignore port state until reset completes.
  USB: Increase reset timeout.
  ...

drivers/usb/Kconfig

@@ -37,6 +37,7 @@ config USB_ARCH_HAS_EHCI
 	default y if ARCH_W90X900
 	default y if ARCH_AT91
 	default y if ARCH_MXC
+	default y if ARCH_MXS
 	default y if ARCH_OMAP3
 	default y if ARCH_CNS3XXX
 	default y if ARCH_VT8500

drivers/usb/chipidea/host.c

@@ -70,6 +70,9 @@ static int host_start(struct ci13xxx *ci)
 	else
 		ci->hcd = hcd;
 
+	if (ci->platdata->flags & CI13XXX_DISABLE_STREAMING)
+		hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+
 	return ret;
 }
 

drivers/usb/class/cdc-acm.c

@@ -1602,6 +1602,9 @@ static const struct usb_device_id acm_ids[] = {
 	{ USB_DEVICE(0x0572, 0x1340), /* Conexant CX93010-2x UCMxx */
 	.driver_info = NO_UNION_NORMAL,
 	},
+	{ USB_DEVICE(0x05f9, 0x4002), /* PSC Scanning, Magellan 800i */
+	.driver_info = NO_UNION_NORMAL,
+	},
 	{ USB_DEVICE(0x1bbb, 0x0003), /* Alcatel OT-I650 */
 	.driver_info = NO_UNION_NORMAL, /* reports zero length descriptor */
 	},

drivers/usb/core/hub.c

@@ -877,6 +877,60 @@ static int hub_hub_status(struct usb_hub *hub,
 	return ret;
 }
 
+static int hub_set_port_link_state(struct usb_hub *hub, int port1,
+			unsigned int link_status)
+{
+	return set_port_feature(hub->hdev,
+			port1 | (link_status << 3),
+			USB_PORT_FEAT_LINK_STATE);
+}
+
+/*
+ * If USB 3.0 ports are placed into the Disabled state, they will no longer
+ * detect any device connects or disconnects.  This is generally not what the
+ * USB core wants, since it expects a disabled port to produce a port status
+ * change event when a new device connects.
+ *
+ * Instead, set the link state to Disabled, wait for the link to settle into
+ * that state, clear any change bits, and then put the port into the RxDetect
+ * state.
+ */
+static int hub_usb3_port_disable(struct usb_hub *hub, int port1)
+{
+	int ret;
+	int total_time;
+	u16 portchange, portstatus;
+
+	if (!hub_is_superspeed(hub->hdev))
+		return -EINVAL;
+
+	ret = hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_SS_DISABLED);
+	if (ret) {
+		dev_err(hub->intfdev, "cannot disable port %d (err = %d)\n",
+				port1, ret);
+		return ret;
+	}
+
+	/* Wait for the link to enter the disabled state. */
+	for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) {
+		ret = hub_port_status(hub, port1, &portstatus, &portchange);
+		if (ret < 0)
+			return ret;
+
+		if ((portstatus & USB_PORT_STAT_LINK_STATE) ==
+				USB_SS_PORT_LS_SS_DISABLED)
+			break;
+		if (total_time >= HUB_DEBOUNCE_TIMEOUT)
+			break;
+		msleep(HUB_DEBOUNCE_STEP);
+	}
+	if (total_time >= HUB_DEBOUNCE_TIMEOUT)
+		dev_warn(hub->intfdev, "Could not disable port %d after %d ms\n",
+				port1, total_time);
+
+	return hub_set_port_link_state(hub, port1, USB_SS_PORT_LS_RX_DETECT);
+}
+
 static int hub_port_disable(struct usb_hub *hub, int port1, int set_state)
 {
 	struct usb_device *hdev = hub->hdev;
@@ -885,8 +939,13 @@ static int hub_port_disable(struct usb_hub *hub, int port1, int set_state)
 	if (hub->ports[port1 - 1]->child && set_state)
 		usb_set_device_state(hub->ports[port1 - 1]->child,
 				USB_STATE_NOTATTACHED);
-	if (!hub->error && !hub_is_superspeed(hub->hdev))
-		ret = clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE);
+	if (!hub->error) {
+		if (hub_is_superspeed(hub->hdev))
+			ret = hub_usb3_port_disable(hub, port1);
+		else
+			ret = clear_port_feature(hdev, port1,
+					USB_PORT_FEAT_ENABLE);
+	}
 	if (ret)
 		dev_err(hub->intfdev, "cannot disable port %d (err = %d)\n",
 				port1, ret);
@@ -2440,7 +2499,7 @@ static unsigned hub_is_wusb(struct usb_hub *hub)
 #define HUB_SHORT_RESET_TIME	10
 #define HUB_BH_RESET_TIME	50
 #define HUB_LONG_RESET_TIME	200
-#define HUB_RESET_TIMEOUT	500
+#define HUB_RESET_TIMEOUT	800
 
 static int hub_port_reset(struct usb_hub *hub, int port1,
 			struct usb_device *udev, unsigned int delay, bool warm);
@@ -2475,6 +2534,10 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 		if (ret < 0)
 			return ret;
 
+		/* The port state is unknown until the reset completes. */
+		if ((portstatus & USB_PORT_STAT_RESET))
+			goto delay;
+
 		/*
 		 * Some buggy devices require a warm reset to be issued even
 		 * when the port appears not to be connected.
@@ -2520,11 +2583,7 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 			if ((portchange & USB_PORT_STAT_C_CONNECTION))
 				return -ENOTCONN;
 
-			/* if we`ve finished resetting, then break out of
-			 * the loop
-			 */
-			if (!(portstatus & USB_PORT_STAT_RESET) &&
-			    (portstatus & USB_PORT_STAT_ENABLE)) {
+			if ((portstatus & USB_PORT_STAT_ENABLE)) {
 				if (hub_is_wusb(hub))
 					udev->speed = USB_SPEED_WIRELESS;
 				else if (hub_is_superspeed(hub->hdev))
@@ -2538,10 +2597,15 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 				return 0;
 			}
 		} else {
-			if (portchange & USB_PORT_STAT_C_BH_RESET)
-				return 0;
+			if (!(portstatus & USB_PORT_STAT_CONNECTION) ||
+					hub_port_warm_reset_required(hub,
+						portstatus))
+				return -ENOTCONN;
+
+			return 0;
 		}
 
+delay:
 		/* switch to the long delay after two short delay failures */
 		if (delay_time >= 2 * HUB_SHORT_RESET_TIME)
 			delay = HUB_LONG_RESET_TIME;
@@ -2565,14 +2629,11 @@ static void hub_port_finish_reset(struct usb_hub *hub, int port1,
 			msleep(10 + 40);
 			update_devnum(udev, 0);
 			hcd = bus_to_hcd(udev->bus);
-			if (hcd->driver->reset_device) {
-				*status = hcd->driver->reset_device(hcd, udev);
-				if (*status < 0) {
-					dev_err(&udev->dev, "Cannot reset "
-							"HCD device state\n");
-					break;
-				}
-			}
+			/* The xHC may think the device is already reset,
+			 * so ignore the status.
+			 */
+			if (hcd->driver->reset_device)
+				hcd->driver->reset_device(hcd, udev);
 		}
 		/* FALL THROUGH */
 	case -ENOTCONN:
@@ -2580,16 +2641,16 @@ static void hub_port_finish_reset(struct usb_hub *hub, int port1,
 		clear_port_feature(hub->hdev,
 				port1, USB_PORT_FEAT_C_RESET);
 		/* FIXME need disconnect() for NOTATTACHED device */
-		if (warm) {
+		if (hub_is_superspeed(hub->hdev)) {
 			clear_port_feature(hub->hdev, port1,
 					USB_PORT_FEAT_C_BH_PORT_RESET);
 			clear_port_feature(hub->hdev, port1,
 					USB_PORT_FEAT_C_PORT_LINK_STATE);
-		} else {
+		}
+		if (!warm)
 			usb_set_device_state(udev, *status
 					? USB_STATE_NOTATTACHED
 					: USB_STATE_DEFAULT);
-		}
 		break;
 	}
 }
@@ -2939,7 +3000,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
 static int finish_port_resume(struct usb_device *udev)
 {
 	int	status = 0;
-	u16	devstatus;
+	u16	devstatus = 0;
 
 	/* caller owns the udev device lock */
 	dev_dbg(&udev->dev, "%s\n",
@@ -2984,7 +3045,13 @@ static int finish_port_resume(struct usb_device *udev)
 	if (status) {
 		dev_dbg(&udev->dev, "gone after usb resume? status %d\n",
 				status);
-	} else if (udev->actconfig) {
+	/*
+	 * There are a few quirky devices which violate the standard
+	 * by claiming to have remote wakeup enabled after a reset,
+	 * which crash if the feature is cleared, hence check for
+	 * udev->reset_resume
+	 */
+	} else if (udev->actconfig && !udev->reset_resume) {
 		le16_to_cpus(&devstatus);
 		if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
 			status = usb_control_msg(udev,
@@ -4638,9 +4705,14 @@ static void hub_events(void)
 			 * SS.Inactive state.
 			 */
 			if (hub_port_warm_reset_required(hub, portstatus)) {
+				int status;
+
 				dev_dbg(hub_dev, "warm reset port %d\n", i);
-				hub_port_reset(hub, i, NULL,
+				status = hub_port_reset(hub, i, NULL,
 						HUB_BH_RESET_TIME, true);
+				if (status < 0)
+					hub_port_disable(hub, i, 1);
+				connect_change = 0;
 			}
 
 			if (connect_change)

drivers/usb/core/quirks.c

@@ -43,6 +43,9 @@ static const struct usb_device_id usb_quirk_list[] = {
 	/* Creative SB Audigy 2 NX */
 	{ USB_DEVICE(0x041e, 0x3020), .driver_info = USB_QUIRK_RESET_RESUME },
 
+	/* Microsoft LifeCam-VX700 v2.0 */
+	{ USB_DEVICE(0x045e, 0x0770), .driver_info = USB_QUIRK_RESET_RESUME },
+
 	/* Logitech Quickcam Fusion */
 	{ USB_DEVICE(0x046d, 0x08c1), .driver_info = USB_QUIRK_RESET_RESUME },
 

drivers/usb/dwc3/debugfs.c

@@ -56,7 +56,7 @@
 #define dump_register(nm)				\
 {							\
 	.name	= __stringify(nm),			\
-	.offset	= DWC3_ ##nm,				\
+	.offset	= DWC3_ ##nm - DWC3_GLOBALS_REGS_START,	\
 }
 
 static const struct debugfs_reg32 dwc3_regs[] = {

drivers/usb/gadget/amd5536udc.c

@@ -3231,7 +3231,7 @@ static int udc_pci_probe(
 	}
 
 	if (!pdev->irq) {
-		dev_err(&dev->pdev->dev, "irq not set\n");
+		dev_err(&pdev->dev, "irq not set\n");
 		kfree(dev);
 		dev = NULL;
 		retval = -ENODEV;
@@ -3250,7 +3250,7 @@ static int udc_pci_probe(
 	dev->txfifo = (u32 __iomem *)(dev->virt_addr + UDC_TXFIFO_ADDR);
 
 	if (request_irq(pdev->irq, udc_irq, IRQF_SHARED, name, dev) != 0) {
-		dev_dbg(&dev->pdev->dev, "request_irq(%d) fail\n", pdev->irq);
+		dev_dbg(&pdev->dev, "request_irq(%d) fail\n", pdev->irq);
 		kfree(dev);
 		dev = NULL;
 		retval = -EBUSY;

drivers/usb/gadget/dummy_hcd.c

@@ -130,10 +130,7 @@ static const char ep0name[] = "ep0";
 static const char *const ep_name[] = {
 	ep0name,				/* everyone has ep0 */
 
-	/* act like a net2280: high speed, six configurable endpoints */
-	"ep-a", "ep-b", "ep-c", "ep-d", "ep-e", "ep-f",
-
-	/* or like pxa250: fifteen fixed function endpoints */
+	/* act like a pxa250: fifteen fixed function endpoints */
 	"ep1in-bulk", "ep2out-bulk", "ep3in-iso", "ep4out-iso", "ep5in-int",
 	"ep6in-bulk", "ep7out-bulk", "ep8in-iso", "ep9out-iso", "ep10in-int",
 	"ep11in-bulk", "ep12out-bulk", "ep13in-iso", "ep14out-iso",
@@ -141,6 +138,10 @@ static const char *const ep_name[] = {
 
 	/* or like sa1100: two fixed function endpoints */
 	"ep1out-bulk", "ep2in-bulk",
+
+	/* and now some generic EPs so we have enough in multi config */
+	"ep3out", "ep4in", "ep5out", "ep6out", "ep7in", "ep8out", "ep9in",
+	"ep10out", "ep11out", "ep12in", "ep13out", "ep14in", "ep15out",
 };
 #define DUMMY_ENDPOINTS	ARRAY_SIZE(ep_name)
 

drivers/usb/gadget/mv_udc_core.c

@@ -1012,7 +1012,7 @@ static void udc_clock_enable(struct mv_udc *udc)
 	unsigned int i;
 
 	for (i = 0; i < udc->clknum; i++)
-		clk_enable(udc->clk[i]);
+		clk_prepare_enable(udc->clk[i]);
 }
 
 static void udc_clock_disable(struct mv_udc *udc)
@@ -1020,7 +1020,7 @@ static void udc_clock_disable(struct mv_udc *udc)
 	unsigned int i;
 
 	for (i = 0; i < udc->clknum; i++)
-		clk_disable(udc->clk[i]);
+		clk_disable_unprepare(udc->clk[i]);
 }
 
 static void udc_stop(struct mv_udc *udc)

drivers/usb/gadget/s3c-hsotg.c

@@ -3477,12 +3477,11 @@ static void s3c_hsotg_delete_debug(struct s3c_hsotg *hsotg)
 /**
  * s3c_hsotg_release - release callback for hsotg device
  * @dev: Device to for which release is called
+ *
+ * Nothing to do as the resource is allocated using devm_ API.
  */
 static void s3c_hsotg_release(struct device *dev)
 {
-	struct s3c_hsotg *hsotg = dev_get_drvdata(dev);
-
-	kfree(hsotg);
 }
 
 /**

drivers/usb/gadget/tcm_usb_gadget.c

@@ -1794,9 +1794,10 @@ static int tcm_usbg_drop_nexus(struct usbg_tpg *tpg)
 	tpg->tpg_nexus = NULL;
 
 	kfree(tv_nexus);
+	ret = 0;
 out:
 	mutex_unlock(&tpg->tpg_mutex);
-	return 0;
+	return ret;
 }
 
 static ssize_t tcm_usbg_tpg_store_nexus(

drivers/usb/gadget/u_serial.c

@@ -887,7 +887,7 @@ static void gs_close(struct tty_struct *tty, struct file *file)
 	pr_debug("gs_close: ttyGS%d (%p,%p) done!\n",
 			port->port_num, tty, file);
 
-	wake_up_interruptible(&port->port.close_wait);
+	wake_up(&port->port.close_wait);
 exit:
 	spin_unlock_irq(&port->port_lock);
 }

drivers/usb/host/ehci-fsl.c

@@ -230,7 +230,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 
 	switch (phy_mode) {
 	case FSL_USB2_PHY_ULPI:
-		if (pdata->controller_ver) {
+		if (pdata->have_sysif_regs && pdata->controller_ver) {
 			/* controller version 1.6 or above */
 			setbits32(non_ehci + FSL_SOC_USB_CTRL,
 					ULPI_PHY_CLK_SEL);
@@ -251,7 +251,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 		portsc |= PORT_PTS_PTW;
 		/* fall through */
 	case FSL_USB2_PHY_UTMI:
-		if (pdata->controller_ver) {
+		if (pdata->have_sysif_regs && pdata->controller_ver) {
 			/* controller version 1.6 or above */
 			setbits32(non_ehci + FSL_SOC_USB_CTRL, UTMI_PHY_EN);
 			mdelay(FSL_UTMI_PHY_DLY);  /* Delay for UTMI PHY CLK to
@@ -267,7 +267,8 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 		break;
 	}
 
-	if (pdata->controller_ver && (phy_mode == FSL_USB2_PHY_ULPI)) {
+	if (pdata->have_sysif_regs && pdata->controller_ver &&
+	    (phy_mode == FSL_USB2_PHY_ULPI)) {
 		/* check PHY_CLK_VALID to get phy clk valid */
 		if (!spin_event_timeout(in_be32(non_ehci + FSL_SOC_USB_CTRL) &
 				PHY_CLK_VALID, FSL_USB_PHY_CLK_TIMEOUT, 0)) {
@@ -278,7 +279,7 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
 
 	ehci_writel(ehci, portsc, &ehci->regs->port_status[port_offset]);
 
-	if (phy_mode != FSL_USB2_PHY_ULPI)
+	if (phy_mode != FSL_USB2_PHY_ULPI && pdata->have_sysif_regs)
 		setbits32(non_ehci + FSL_SOC_USB_CTRL, USB_CTRL_USB_EN);
 
 	return 0;

drivers/usb/host/ehci-mv.c

@@ -43,7 +43,7 @@ static void ehci_clock_enable(struct ehci_hcd_mv *ehci_mv)
 	unsigned int i;
 
 	for (i = 0; i < ehci_mv->clknum; i++)
-		clk_enable(ehci_mv->clk[i]);
+		clk_prepare_enable(ehci_mv->clk[i]);
 }
 
 static void ehci_clock_disable(struct ehci_hcd_mv *ehci_mv)
@@ -51,7 +51,7 @@ static void ehci_clock_disable(struct ehci_hcd_mv *ehci_mv)
 	unsigned int i;
 
 	for (i = 0; i < ehci_mv->clknum; i++)
-		clk_disable(ehci_mv->clk[i]);
+		clk_disable_unprepare(ehci_mv->clk[i]);
 }
 
 static int mv_ehci_enable(struct ehci_hcd_mv *ehci_mv)

drivers/usb/host/ehci-pci.c

@@ -200,6 +200,26 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		break;
 	}
 
+	/* optional debug port, normally in the first BAR */
+	temp = pci_find_capability(pdev, PCI_CAP_ID_DBG);
+	if (temp) {
+		pci_read_config_dword(pdev, temp, &temp);
+		temp >>= 16;
+		if (((temp >> 13) & 7) == 1) {
+			u32 hcs_params = ehci_readl(ehci,
+						    &ehci->caps->hcs_params);
+
+			temp &= 0x1fff;
+			ehci->debug = hcd->regs + temp;
+			temp = ehci_readl(ehci, &ehci->debug->control);
+			ehci_info(ehci, "debug port %d%s\n",
+				  HCS_DEBUG_PORT(hcs_params),
+				  (temp & DBGP_ENABLED) ? " IN USE" : "");
+			if (!(temp & DBGP_ENABLED))
+				ehci->debug = NULL;
+		}
+	}
+
 	retval = ehci_setup(hcd);
 	if (retval)
 		return retval;
@@ -228,25 +248,6 @@ static int ehci_pci_setup(struct usb_hcd *hcd)
 		break;
 	}
 
-	/* optional debug port, normally in the first BAR */
-	temp = pci_find_capability(pdev, 0x0a);
-	if (temp) {
-		pci_read_config_dword(pdev, temp, &temp);
-		temp >>= 16;
-		if ((temp & (3 << 13)) == (1 << 13)) {
-			temp &= 0x1fff;
-			ehci->debug = hcd->regs + temp;
-			temp = ehci_readl(ehci, &ehci->debug->control);
-			ehci_info(ehci, "debug port %d%s\n",
-				HCS_DEBUG_PORT(ehci->hcs_params),
-				(temp & DBGP_ENABLED)
-					? " IN USE"
-					: "");
-			if (!(temp & DBGP_ENABLED))
-				ehci->debug = NULL;
-		}
-	}
-
 	/* at least the Genesys GL880S needs fixup here */
 	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
 	temp &= 0x0f;

drivers/usb/host/fsl-mph-dr-of.c

@@ -142,6 +142,9 @@ static int usb_get_ver_info(struct device_node *np)
 			return ver;
 	}
 
+	if (of_device_is_compatible(np, "fsl,mpc5121-usb2-dr"))
+		return FSL_USB_VER_OLD;
+
 	if (of_device_is_compatible(np, "fsl-usb2-mph")) {
 		if (of_device_is_compatible(np, "fsl-usb2-mph-v1.6"))
 			ver = FSL_USB_VER_1_6;

drivers/usb/host/imx21-hcd.c

@@ -58,6 +58,7 @@
 #include <linux/usb.h>
 #include <linux/usb/hcd.h>
 #include <linux/dma-mapping.h>
+#include <linux/module.h>
 
 #include "imx21-hcd.h"
 

drivers/usb/host/ohci-tmio.c

@@ -128,7 +128,8 @@ static void tmio_start_hc(struct platform_device *dev)
 	tmio_iowrite8(2, tmio->ccr + CCR_INTC);
 
 	dev_info(&dev->dev, "revision %d @ 0x%08llx, irq %d\n",
-			tmio_ioread8(tmio->ccr + CCR_REVID), hcd->rsrc_start, hcd->irq);
+			tmio_ioread8(tmio->ccr + CCR_REVID),
+			(u64) hcd->rsrc_start, hcd->irq);
 }
 
 static int ohci_tmio_start(struct usb_hcd *hcd)

drivers/usb/host/xhci-hub.c

@@ -761,12 +761,39 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 			break;
 		case USB_PORT_FEAT_LINK_STATE:
 			temp = xhci_readl(xhci, port_array[wIndex]);
+
+			/* Disable port */
+			if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
+				xhci_dbg(xhci, "Disable port %d\n", wIndex);
+				temp = xhci_port_state_to_neutral(temp);
+				/*
+				 * Clear all change bits, so that we get a new
+				 * connection event.
+				 */
+				temp |= PORT_CSC | PORT_PEC | PORT_WRC |
+					PORT_OCC | PORT_RC | PORT_PLC |
+					PORT_CEC;
+				xhci_writel(xhci, temp | PORT_PE,
+					port_array[wIndex]);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
+			/* Put link in RxDetect (enable port) */
+			if (link_state == USB_SS_PORT_LS_RX_DETECT) {
+				xhci_dbg(xhci, "Enable port %d\n", wIndex);
+				xhci_set_link_state(xhci, port_array, wIndex,
+						link_state);
+				temp = xhci_readl(xhci, port_array[wIndex]);
+				break;
+			}
+
 			/* Software should not attempt to set
-			 * port link state above '5' (Rx.Detect) and the port
+			 * port link state above '3' (U3) and the port
 			 * must be enabled.
 			 */
 			if ((temp & PORT_PE) == 0 ||
-				(link_state > USB_SS_PORT_LS_RX_DETECT)) {
+				(link_state > USB_SS_PORT_LS_U3)) {
 				xhci_warn(xhci, "Cannot set link state.\n");
 				goto error;
 			}
@@ -957,6 +984,7 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 	int max_ports;
 	__le32 __iomem **port_array;
 	struct xhci_bus_state *bus_state;
+	bool reset_change = false;
 
 	max_ports = xhci_get_ports(hcd, &port_array);
 	bus_state = &xhci->bus_state[hcd_index(hcd)];
@@ -988,6 +1016,12 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 			buf[(i + 1) / 8] |= 1 << (i + 1) % 8;
 			status = 1;
 		}
+		if ((temp & PORT_RC))
+			reset_change = true;
+	}
+	if (!status && !reset_change) {
+		xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+		clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 	}
 	spin_unlock_irqrestore(&xhci->lock, flags);
 	return status ? retval : 0;

drivers/usb/host/xhci-mem.c

@@ -1250,6 +1250,8 @@ static unsigned int xhci_microframes_to_exponent(struct usb_device *udev,
 static unsigned int xhci_parse_microframe_interval(struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
+	if (ep->desc.bInterval == 0)
+		return 0;
 	return xhci_microframes_to_exponent(udev, ep,
 			ep->desc.bInterval, 0, 15);
 }

drivers/usb/host/xhci-ring.c

@@ -1725,6 +1725,15 @@ cleanup:
 	if (bogus_port_status)
 		return;
 
+	/*
+	 * xHCI port-status-change events occur when the "or" of all the
+	 * status-change bits in the portsc register changes from 0 to 1.
+	 * New status changes won't cause an event if any other change
+	 * bits are still set.  When an event occurs, switch over to
+	 * polling to avoid losing status changes.
+	 */
+	xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 	spin_unlock(&xhci->lock);
 	/* Pass this up to the core */
 	usb_hcd_poll_rh_status(hcd);

drivers/usb/host/xhci.c

@@ -884,6 +884,11 @@ int xhci_suspend(struct xhci_hcd *xhci)
 			xhci->shared_hcd->state != HC_STATE_SUSPENDED)
 		return -EINVAL;
 
+	/* Don't poll the roothubs on bus suspend. */
+	xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+	clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	del_timer_sync(&hcd->rh_timer);
+
 	spin_lock_irq(&xhci->lock);
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
@@ -1069,6 +1074,11 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated)
 	if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
 		compliance_mode_recovery_timer_init(xhci);
 
+	/* Re-enable port polling. */
+	xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	usb_hcd_poll_rh_status(hcd);
+
 	return retval;
 }
 #endif	/* CONFIG_PM */

drivers/usb/misc/usbtest.c

@@ -2179,7 +2179,7 @@ usbtest_ioctl(struct usb_interface *intf, unsigned int code, void *buf)
 		if (dev->out_pipe == 0 || !param->length || param->sglen < 4)
 			break;
 		retval = 0;
-		dev_info(&intf->dev, "TEST 17:  unlink from %d queues of "
+		dev_info(&intf->dev, "TEST 24:  unlink from %d queues of "
 				"%d %d-byte writes\n",
 				param->iterations, param->sglen, param->length);
 		for (i = param->iterations; retval == 0 && i > 0; --i) {

drivers/usb/musb/musb_core.c

@@ -2298,10 +2298,7 @@ static int __init musb_init(void)
 	if (usb_disabled())
 		return 0;
 
-	pr_info("%s: version " MUSB_VERSION ", "
-		"?dma?"
-		", "
-		"otg (peripheral+host)",
+	pr_info("%s: version " MUSB_VERSION ", ?dma?, otg (peripheral+host)\n",
 		musb_driver_name);
 	return platform_driver_register(&musb_driver);
 }

drivers/usb/musb/musb_dsps.c

@@ -134,6 +134,11 @@ static const resource_size_t dsps_control_module_phys[] = {
 	DSPS_AM33XX_CONTROL_MODULE_PHYS_1,
 };
 
+#define USBPHY_CM_PWRDN		(1 << 0)
+#define USBPHY_OTG_PWRDN	(1 << 1)
+#define USBPHY_OTGVDET_EN	(1 << 19)
+#define USBPHY_OTGSESSEND_EN	(1 << 20)
+
 /**
  * musb_dsps_phy_control - phy on/off
  * @glue: struct dsps_glue *

drivers/usb/otg/Kconfig

@@ -110,7 +110,7 @@ config AB8500_USB
 
 config FSL_USB2_OTG
 	bool "Freescale USB OTG Transceiver Driver"
-	depends on USB_EHCI_FSL && USB_GADGET_FSL_USB2 && USB_SUSPEND
+	depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_SUSPEND
 	select USB_OTG
 	select USB_OTG_UTILS
 	help

drivers/usb/otg/mv_otg.c

@@ -240,7 +240,7 @@ static void otg_clock_enable(struct mv_otg *mvotg)
 	unsigned int i;
 
 	for (i = 0; i < mvotg->clknum; i++)
-		clk_enable(mvotg->clk[i]);
+		clk_prepare_enable(mvotg->clk[i]);
 }
 
 static void otg_clock_disable(struct mv_otg *mvotg)
@@ -248,7 +248,7 @@ static void otg_clock_disable(struct mv_otg *mvotg)
 	unsigned int i;
 
 	for (i = 0; i < mvotg->clknum; i++)
-		clk_disable(mvotg->clk[i]);
+		clk_disable_unprepare(mvotg->clk[i]);
 }
 
 static int mv_otg_enable_internal(struct mv_otg *mvotg)

drivers/usb/renesas_usbhs/mod_gadget.c

@@ -545,15 +545,6 @@ static int usbhsg_pipe_disable(struct usbhsg_uep *uep)
 	return 0;
 }
 
-static void usbhsg_uep_init(struct usbhsg_gpriv *gpriv)
-{
-	int i;
-	struct usbhsg_uep *uep;
-
-	usbhsg_for_each_uep_with_dcp(uep, gpriv, i)
-		uep->pipe = NULL;
-}
-
 /*
  *
  *		usb_ep_ops
@@ -610,7 +601,12 @@ static int usbhsg_ep_disable(struct usb_ep *ep)
 {
 	struct usbhsg_uep *uep = usbhsg_ep_to_uep(ep);
 
-	return usbhsg_pipe_disable(uep);
+	usbhsg_pipe_disable(uep);
+
+	uep->pipe->mod_private	= NULL;
+	uep->pipe		= NULL;
+
+	return 0;
 }
 
 static struct usb_request *usbhsg_ep_alloc_request(struct usb_ep *ep,
@@ -761,9 +757,8 @@ static int usbhsg_try_start(struct usbhs_priv *priv, u32 status)
 	usbhs_pipe_init(priv,
 			usbhsg_dma_map_ctrl);
 	usbhs_fifo_init(priv);
-	usbhsg_uep_init(gpriv);
 
-	/* dcp init */
+	/* dcp init instead of usbhsg_ep_enable() */
 	dcp->pipe		= usbhs_dcp_malloc(priv);
 	dcp->pipe->mod_private	= dcp;
 	usbhs_pipe_config_update(dcp->pipe, 0, 0, 64);
@@ -825,7 +820,7 @@ static int usbhsg_try_stop(struct usbhs_priv *priv, u32 status)
 	usbhs_sys_set_test_mode(priv, 0);
 	usbhs_sys_function_ctrl(priv, 0);
 
-	usbhsg_pipe_disable(dcp);
+	usbhsg_ep_disable(&dcp->ep);
 
 	dev_dbg(dev, "stop gadget\n");
 
@@ -998,6 +993,7 @@ int usbhs_mod_gadget_probe(struct usbhs_priv *priv)
 	 */
 	usbhsg_for_each_uep_with_dcp(uep, gpriv, i) {
 		uep->gpriv	= gpriv;
+		uep->pipe	= NULL;
 		snprintf(uep->ep_name, EP_NAME_SIZE, "ep%d", i);
 
 		uep->ep.name		= uep->ep_name;

drivers/usb/renesas_usbhs/mod_host.c

@@ -661,9 +661,10 @@ static void usbhsh_queue_done(struct usbhs_priv *priv, struct usbhs_pkt *pkt)
 		status = -ESHUTDOWN;
 
 	urb->actual_length = pkt->actual;
-	usbhsh_ureq_free(hpriv, ureq);
 
 	usbhsh_endpoint_sequence_save(hpriv, urb, pkt);
+	usbhsh_ureq_free(hpriv, ureq);
+
 	usbhsh_pipe_detach(hpriv, usbhsh_ep_to_uep(urb->ep));
 
 	usb_hcd_unlink_urb_from_ep(hcd, urb);

drivers/usb/serial/ftdi_sio.c

@@ -875,6 +875,8 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(FTDI_VID, FTDI_DISTORTEC_JTAG_LOCK_PICK_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(FTDI_VID, FTDI_LUMEL_PD12_PID) },
+	/* Crucible Devices */
+	{ USB_DEVICE(FTDI_VID, FTDI_CT_COMET_PID) },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };

drivers/usb/serial/ftdi_sio_ids.h

@@ -1259,3 +1259,9 @@
  * ATI command output: Cinterion MC55i
  */
 #define FTDI_CINTERION_MC55I_PID	0xA951
+
+/*
+ * Product: Comet Caller ID decoder
+ * Manufacturer: Crucible Technologies
+ */
+#define FTDI_CT_COMET_PID	0x8e08

drivers/usb/serial/option.c

@@ -288,6 +288,7 @@ static void option_instat_callback(struct urb *urb);
 #define ALCATEL_VENDOR_ID			0x1bbb
 #define ALCATEL_PRODUCT_X060S_X200		0x0000
 #define ALCATEL_PRODUCT_X220_X500D		0x0017
+#define ALCATEL_PRODUCT_L100V			0x011e
 
 #define PIRELLI_VENDOR_ID			0x1266
 #define PIRELLI_PRODUCT_C100_1			0x1002
@@ -429,9 +430,12 @@ static void option_instat_callback(struct urb *urb);
 #define MEDIATEK_VENDOR_ID			0x0e8d
 #define MEDIATEK_PRODUCT_DC_1COM		0x00a0
 #define MEDIATEK_PRODUCT_DC_4COM		0x00a5
+#define MEDIATEK_PRODUCT_DC_4COM2		0x00a7
 #define MEDIATEK_PRODUCT_DC_5COM		0x00a4
 #define MEDIATEK_PRODUCT_7208_1COM		0x7101
 #define MEDIATEK_PRODUCT_7208_2COM		0x7102
+#define MEDIATEK_PRODUCT_7103_2COM		0x7103
+#define MEDIATEK_PRODUCT_7106_2COM		0x7106
 #define MEDIATEK_PRODUCT_FP_1COM		0x0003
 #define MEDIATEK_PRODUCT_FP_2COM		0x0023
 #define MEDIATEK_PRODUCT_FPDC_1COM		0x0043
@@ -441,6 +445,10 @@ static void option_instat_callback(struct urb *urb);
 #define CELLIENT_VENDOR_ID			0x2692
 #define CELLIENT_PRODUCT_MEN200			0x9005
 
+/* Hyundai Petatel Inc. products */
+#define PETATEL_VENDOR_ID			0x1ff4
+#define PETATEL_PRODUCT_NP10T			0x600e
+
 /* some devices interfaces need special handling due to a number of reasons */
 enum option_blacklist_reason {
 		OPTION_BLACKLIST_NONE = 0,
@@ -923,7 +931,8 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0257, 0xff, 0xff, 0xff), /* ZTE MF821 */
 	  .driver_info = (kernel_ulong_t)&net_intf3_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0265, 0xff, 0xff, 0xff) },
-	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0284, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0284, 0xff, 0xff, 0xff), /* ZTE MF880 */
+	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0317, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0326, 0xff, 0xff, 0xff),
 	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
@@ -1190,6 +1199,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = (kernel_ulong_t)&alcatel_x200_blacklist
 	},
 	{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X220_X500D) },
+	{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_L100V),
+	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
 	{ USB_DEVICE(AIRPLUS_VENDOR_ID, AIRPLUS_PRODUCT_MCD650) },
 	{ USB_DEVICE(TLAYTECH_VENDOR_ID, TLAYTECH_PRODUCT_TEU800) },
 	{ USB_DEVICE(LONGCHEER_VENDOR_ID, FOUR_G_SYSTEMS_PRODUCT_W14),
@@ -1294,7 +1305,12 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FP_2COM, 0x0a, 0x00, 0x00) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FPDC_1COM, 0x0a, 0x00, 0x00) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_FPDC_2COM, 0x0a, 0x00, 0x00) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_7103_2COM, 0xff, 0x00, 0x00) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_7106_2COM, 0x02, 0x02, 0x01) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x02, 0x01) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MEDIATEK_VENDOR_ID, MEDIATEK_PRODUCT_DC_4COM2, 0xff, 0x00, 0x00) },
 	{ USB_DEVICE(CELLIENT_VENDOR_ID, CELLIENT_PRODUCT_MEN200) },
+	{ USB_DEVICE(PETATEL_VENDOR_ID, PETATEL_PRODUCT_NP10T) },
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);