[ARM] 5288/1: [AT91] Remove SMC configuration from devices.c files

In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-at91/at91cap9_devices.c

@@ -406,28 +406,13 @@ static struct platform_device at91cap9_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
 
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
-	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
-
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(1)
-			| AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(1));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(6)
-			| AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(6));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(8) | AT91_SMC_NRDCYCLE_(8));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(1));
+	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
 	if (data->enable_pin)

arch/arm/mach-at91/at91sam9260_devices.c

@@ -313,7 +313,7 @@ static struct platform_device at91sam9260_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -321,42 +321,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	if (cpu_is_at91sam9260()) {
-		/* Timing for sam9260 */
-		/* set the bus interface characteristics */
-		at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-				| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-		at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-				| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-		at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-		if (data->bus_width_16)
-			mode = AT91_SMC_DBW_16;
-		else
-			mode = AT91_SMC_DBW_8;
-		at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-	}
-
-	if (cpu_is_at91sam9g20()) {
-		/* Timing for sam9g20 */
-		/* set the bus interface characteristics */
-		at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
-				| AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-
-		at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
-				| AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
-
-		at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
-
-		if (data->bus_width_16)
-			mode = AT91_SMC_DBW_16;
-		else
-			mode = AT91_SMC_DBW_8;
-		at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
-	}
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);

arch/arm/mach-at91/at91sam9261_devices.c

@@ -223,7 +223,7 @@ static struct platform_device atmel_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -231,21 +231,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);

arch/arm/mach-at91/at91sam9263_devices.c

@@ -382,7 +382,7 @@ static struct platform_device at91sam9263_nand_device = {
 
 void __init at91_add_device_nand(struct atmel_nand_data *data)
 {
-	unsigned long csa, mode;
+	unsigned long csa;
 
 	if (!data)
 		return;
@@ -390,21 +390,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	if (data->bus_width_16)
-		mode = AT91_SMC_DBW_16;
-	else
-		mode = AT91_SMC_DBW_8;
-	at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -232,17 +232,6 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	csa = at91_sys_read(AT91_MATRIX_EBICSA);
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
-	/* set the bus interface characteristics */
-	at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
-			| AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
-	at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
-			| AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
-	at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
-	at91_sys_write(AT91_SMC_MODE(3), AT91_SMC_DBW_8 | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
-
 	/* enable pin */
 	if (data->enable_pin)
 		at91_set_gpio_output(data->enable_pin, 1);