Merge branch 'cleanup' into for-linus

Conflicts:
	arch/arm/mach-imx/mach-imx27_visstrim_m10.c

arch/arm/include/asm/hardware/linkup-l1110.h

@@ -1,48 +0,0 @@
-/*
-*
-* Definitions for H3600 Handheld Computer
-*
-* Copyright 2001 Compaq Computer Corporation.
-*
-* Use consistent with the GNU GPL is permitted,
-* provided that this copyright notice is
-* preserved in its entirety in all copies and derived works.
-*
-* COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED,
-* AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS
-* FITNESS FOR ANY PARTICULAR PURPOSE.
-*
-* Author: Jamey Hicks.
-*
-*/
-
-/* LinkUp Systems PCCard/CompactFlash Interface for SA-1100 */
-
-/* PC Card Status Register */
-#define LINKUP_PRS_S1	(1 << 0) /* voltage control bits S1-S4 */
-#define LINKUP_PRS_S2	(1 << 1)
-#define LINKUP_PRS_S3	(1 << 2)
-#define LINKUP_PRS_S4	(1 << 3)
-#define LINKUP_PRS_BVD1	(1 << 4)
-#define LINKUP_PRS_BVD2	(1 << 5)
-#define LINKUP_PRS_VS1	(1 << 6)
-#define LINKUP_PRS_VS2	(1 << 7)
-#define LINKUP_PRS_RDY	(1 << 8)
-#define LINKUP_PRS_CD1	(1 << 9)
-#define LINKUP_PRS_CD2	(1 << 10)
-
-/* PC Card Command Register */
-#define LINKUP_PRC_S1	(1 << 0)
-#define LINKUP_PRC_S2	(1 << 1)
-#define LINKUP_PRC_S3	(1 << 2)
-#define LINKUP_PRC_S4	(1 << 3)
-#define LINKUP_PRC_RESET (1 << 4)
-#define LINKUP_PRC_APOE	(1 << 5) /* Auto Power Off Enable: clears S1-S4 when either nCD goes high */
-#define LINKUP_PRC_CFE	(1 << 6) /* CompactFlash mode Enable: addresses A[10:0] only, A[25:11] high */
-#define LINKUP_PRC_SOE	(1 << 7) /* signal output driver enable */
-#define LINKUP_PRC_SSP	(1 << 8) /* sock select polarity: 0 for socket 0, 1 for socket 1 */
-#define LINKUP_PRC_MBZ	(1 << 15) /* must be zero */
-
-struct linkup_l1110 {
-	volatile short prc;
-};

arch/arm/include/asm/thread_info.h

@@ -59,7 +59,9 @@ struct thread_info {
 	__u32			syscall;	/* syscall number */
 	__u8			used_cp[16];	/* thread used copro */
 	unsigned long		tp_value;
+#ifdef CONFIG_CRUNCH
 	struct crunch_state	crunchstate;
+#endif
 	union fp_state		fpstate __attribute__((aligned(8)));
 	union vfp_state		vfpstate;
 #ifdef CONFIG_ARM_THUMBEE

arch/arm/kernel/asm-offsets.c

@@ -59,10 +59,12 @@ int main(void)
   DEFINE(TI_USED_CP,		offsetof(struct thread_info, used_cp));
   DEFINE(TI_TP_VALUE,		offsetof(struct thread_info, tp_value));
   DEFINE(TI_FPSTATE,		offsetof(struct thread_info, fpstate));
+#ifdef CONFIG_VFP
   DEFINE(TI_VFPSTATE,		offsetof(struct thread_info, vfpstate));
 #ifdef CONFIG_SMP
   DEFINE(VFP_CPU,		offsetof(union vfp_state, hard.cpu));
 #endif
+#endif
 #ifdef CONFIG_ARM_THUMBEE
   DEFINE(TI_THUMBEE_STATE,	offsetof(struct thread_info, thumbee_state));
 #endif

arch/arm/mach-imx/mach-imx27_visstrim_m10.c

@@ -32,13 +32,13 @@
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/leds.h>
-#include <linux/memblock.h>
 #include <media/soc_camera.h>
 #include <sound/tlv320aic32x4.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include <asm/system_info.h>
+#include <asm/memblock.h>
 #include <mach/common.h>
 #include <mach/hardware.h>
 #include <mach/iomux-mx27.h>
@@ -233,10 +233,8 @@ static void __init visstrim_camera_init(void)
 static void __init visstrim_reserve(void)
 {
 	/* reserve 4 MiB for mx2-camera */
-	mx2_camera_base = memblock_alloc(MX2_CAMERA_BUF_SIZE,
+	mx2_camera_base = memblock_steal(MX2_CAMERA_BUF_SIZE,
 			MX2_CAMERA_BUF_SIZE);
-	memblock_free(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
-	memblock_remove(mx2_camera_base, MX2_CAMERA_BUF_SIZE);
 }
 
 /* GPIOs used as events for applications */

arch/arm/mach-sa1100/include/mach/SA-1111.h

@@ -1,5 +0,0 @@
-/*
- * Moved to new location
- */
-#warning using old SA-1111.h - update to <asm/hardware/sa1111.h>
-#include <asm/hardware/sa1111.h>

arch/arm/mach-sa1100/include/mach/lart.h

@@ -1,13 +0,0 @@
-#ifndef _INCLUDE_LART_H
-#define _INCLUDE_LART_H
-
-#define LART_GPIO_ETH0			GPIO_GPIO0
-#define LART_IRQ_ETH0			IRQ_GPIO0
-
-#define LART_GPIO_IDE			GPIO_GPIO1
-#define LART_IRQ_IDE			IRQ_GPIO1
-
-#define LART_GPIO_UCB1200		GPIO_GPIO18
-#define LART_IRQ_UCB1200		IRQ_GPIO18
-
-#endif