Merge branch 'samsung/cleanup' into next/boards

Conflicts:
	arch/arm/mach-imx/mach-imx6q.c
	arch/arm/mach-omap2/board-ti8168evm.c
	arch/arm/mach-s3c64xx/Kconfig
	arch/arm/mach-tegra/Makefile
	arch/arm/mach-tegra/board-dt-tegra20.c
	arch/arm/mach-tegra/common.c

Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/insignal-boards.txt

@@ -0,0 +1,8 @@
+* Insignal's Exynos4210 based Origen evaluation board
+
+Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+    - compatible = should be one or more of the following.
+        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

Documentation/devicetree/bindings/arm/samsung-boards.txt

@@ -0,0 +1,8 @@
+* Samsung's Exynos4210 based SMDKV310 evaluation board
+
+SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC.
+
+Required root node properties:
+    - compatible = should be one or more of the following.
+        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
+        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

Documentation/devicetree/bindings/dma/arm-pl330.txt

@@ -0,0 +1,30 @@
+* ARM PrimeCell PL330 DMA Controller
+
+The ARM PrimeCell PL330 DMA controller can move blocks of memory contents
+between memory and peripherals or memory to memory.
+
+Required properties:
+  - compatible: should include both "arm,pl330" and "arm,primecell".
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+
+Example:
+
+	pdma0: pdma@12680000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x12680000 0x1000>;
+		interrupts = <99>;
+	};
+
+Client drivers (device nodes requiring dma transfers from dev-to-mem or
+mem-to-dev) should specify the DMA channel numbers using a two-value pair
+as shown below.
+
+  [property name]  = <[phandle of the dma controller] [dma request id]>;
+
+      where 'dma request id' is the dma request number which is connected
+      to the client controller. The 'property name' is recommended to be
+      of the form <name>-dma-channel.
+
+  Example:  tx-dma-channel = <&pdma0 12>;

Documentation/devicetree/bindings/gpio/gpio-samsung.txt

@@ -0,0 +1,40 @@
+Samsung Exynos4 GPIO Controller
+
+Required properties:
+- compatible: Compatible property value should be "samsung,exynos4-gpio>".
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes
+  should be the following with values derived from the SoC user manual.
+     <[phandle of the gpio controller node]
+      [pin number within the gpio controller]
+      [mux function]
+      [pull up/down]
+      [drive strength]>
+
+  Values for gpio specifier:
+  - Pin number: is a value between 0 to 7.
+  - Pull Up/Down: 0 - Pull Up/Down Disabled.
+                  1 - Pull Down Enabled.
+                  3 - Pull Up Enabled.
+  - Drive Strength: 0 - 1x,
+                    1 - 3x,
+                    2 - 2x,
+                    3 - 4x
+
+- gpio-controller: Specifies that the node is a gpio controller.
+- #address-cells: should be 1.
+- #size-cells: should be 1.
+
+Example:
+
+	gpa0: gpio-controller@11400000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "samsung,exynos4-gpio";
+		reg = <0x11400000 0x20>;
+		#gpio-cells = <4>;
+		gpio-controller;
+	};

Documentation/devicetree/bindings/input/samsung-keypad.txt

@@ -0,0 +1,88 @@
+* Samsung's Keypad Controller device tree bindings
+
+Samsung's Keypad controller is used to interface a SoC with a matrix-type
+keypad device. The keypad controller supports multiple row and column lines.
+A key can be placed at each intersection of a unique row and a unique column.
+The keypad controller can sense a key-press and key-release and report the
+event using a interrupt to the cpu.
+
+Required SoC Specific Properties:
+- compatible: should be one of the following
+  - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad
+    controller.
+  - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad
+    controller.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu.
+
+Required Board Specific Properties:
+- samsung,keypad-num-rows: Number of row lines connected to the keypad
+  controller.
+
+- samsung,keypad-num-columns: Number of column lines connected to the
+  keypad controller.
+
+- row-gpios: List of gpios used as row lines. The gpio specifier for
+  this property depends on the gpio controller to which these row lines
+  are connected.
+
+- col-gpios: List of gpios used as column lines. The gpio specifier for
+  this property depends on the gpio controller to which these column
+  lines are connected.
+
+- Keys represented as child nodes: Each key connected to the keypad
+  controller is represented as a child node to the keypad controller
+  device node and should include the following properties.
+  - keypad,row: the row number to which the key is connected.
+  - keypad,column: the column number to which the key is connected.
+  - linux,code: the key-code to be reported when the key is pressed
+    and released.
+
+Optional Properties specific to linux:
+- linux,keypad-no-autorepeat: do no enable autorepeat feature.
+- linux,keypad-wakeup: use any event on keypad as wakeup event.
+
+
+Example:
+	keypad@100A0000 {
+		compatible = "samsung,s5pv210-keypad";
+		reg = <0x100A0000 0x100>;
+		interrupts = <173>;
+		samsung,keypad-num-rows = <2>;
+		samsung,keypad-num-columns = <8>;
+		linux,input-no-autorepeat;
+		linux,input-wakeup;
+
+		row-gpios = <&gpx2 0 3 3 0
+			     &gpx2 1 3 3 0>;
+
+		col-gpios = <&gpx1 0 3 0 0
+			     &gpx1 1 3 0 0
+			     &gpx1 2 3 0 0
+			     &gpx1 3 3 0 0
+			     &gpx1 4 3 0 0
+			     &gpx1 5 3 0 0
+			     &gpx1 6 3 0 0
+			     &gpx1 7 3 0 0>;
+
+		key_1 {
+			keypad,row = <0>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <0>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+	};

Documentation/devicetree/bindings/rtc/s3c-rtc.txt

@@ -0,0 +1,20 @@
+* Samsung's S3C Real Time Clock controller
+
+Required properties:
+- compatible: should be one of the following.
+    * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc.
+    * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: Two interrupt numbers to the cpu should be specified. First
+  interrupt number is the rtc alarm interupt and second interrupt number
+  is the rtc tick interrupt. The number of cells representing a interrupt
+  depends on the parent interrupt controller.
+
+Example:
+
+	rtc@10070000 {
+		compatible = "samsung,s3c6410-rtc";
+		reg = <0x10070000 0x100>;
+		interrupts = <44 0 45 0>;
+	};

Documentation/devicetree/bindings/serial/samsung_uart.txt

@@ -0,0 +1,14 @@
+* Samsung's UART Controller
+
+The Samsung's UART controller is used for interfacing SoC with serial communicaion
+devices.
+
+Required properties:
+- compatible: should be
+  - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports.
+
+- reg: base physical address of the controller and length of memory mapped
+  region.
+
+- interrupts: interrupt number to the cpu. The interrupt specifier format depends
+  on the interrupt controller parent.

Documentation/virtual/kvm/api.txt

@@ -1100,6 +1100,15 @@ emulate them efficiently. The fields in each entry are defined as follows:
    eax, ebx, ecx, edx: the values returned by the cpuid instruction for
          this function/index combination
 
+The TSC deadline timer feature (CPUID leaf 1, ecx[24]) is always returned
+as false, since the feature depends on KVM_CREATE_IRQCHIP for local APIC
+support.  Instead it is reported via
+
+  ioctl(KVM_CHECK_EXTENSION, KVM_CAP_TSC_DEADLINE_TIMER)
+
+if that returns true and you use KVM_CREATE_IRQCHIP, or if you emulate the
+feature in userspace, then you can enable the feature for KVM_SET_CPUID2.
+
 4.47 KVM_PPC_GET_PVINFO
 
 Capability: KVM_CAP_PPC_GET_PVINFO
@@ -1151,6 +1160,13 @@ following flags are specified:
 /* Depends on KVM_CAP_IOMMU */
 #define KVM_DEV_ASSIGN_ENABLE_IOMMU	(1 << 0)
 
+The KVM_DEV_ASSIGN_ENABLE_IOMMU flag is a mandatory option to ensure
+isolation of the device.  Usages not specifying this flag are deprecated.
+
+Only PCI header type 0 devices with PCI BAR resources are supported by
+device assignment.  The user requesting this ioctl must have read/write
+access to the PCI sysfs resource files associated with the device.
+
 4.49 KVM_DEASSIGN_PCI_DEVICE
 
 Capability: KVM_CAP_DEVICE_DEASSIGNMENT

MAINTAINERS

@@ -1124,13 +1124,6 @@ S:	Supported
 F:	arch/arm/mach-shmobile/
 F:	drivers/sh/
 
-ARM/TELECHIPS ARM ARCHITECTURE
-M:	"Hans J. Koch" <hjk@hansjkoch.de>
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-F:	arch/arm/plat-tcc/
-F:	arch/arm/mach-tcc8k/
-
 ARM/TECHNOLOGIC SYSTEMS TS7250 MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -2700,7 +2693,7 @@ FIREWIRE SUBSYSTEM
 M:	Stefan Richter <stefanr@s5r6.in-berlin.de>
 L:	linux1394-devel@lists.sourceforge.net
 W:	http://ieee1394.wiki.kernel.org/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394.git
 S:	Maintained
 F:	drivers/firewire/
 F:	include/linux/firewire*.h
@@ -3101,6 +3094,7 @@ F:	include/linux/hid*
 
 HIGH-RESOLUTION TIMERS, CLOCKEVENTS, DYNTICKS
 M:	Thomas Gleixner <tglx@linutronix.de>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git timers/core
 S:	Maintained
 F:	Documentation/timers/
 F:	kernel/hrtimer.c
@@ -3610,7 +3604,7 @@ F:	net/irda/
 IRQ SUBSYSTEM
 M:	Thomas Gleixner <tglx@linutronix.de>
 S:	Maintained
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip.git irq/core
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git irq/core
 F:	kernel/irq/
 
 ISAPNP
@@ -4098,7 +4092,7 @@ F:	drivers/hwmon/lm90.c
 LOCKDEP AND LOCKSTAT
 M:	Peter Zijlstra <peterz@infradead.org>
 M:	Ingo Molnar <mingo@redhat.com>
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git core/locking
 S:	Maintained
 F:	Documentation/lockdep*.txt
 F:	Documentation/lockstat.txt
@@ -4280,7 +4274,9 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	Documentation/dvb/
 F:	Documentation/video4linux/
+F:	Documentation/DocBook/media/
 F:	drivers/media/
+F:	drivers/staging/media/
 F:	include/media/
 F:	include/linux/dvb/
 F:	include/linux/videodev*.h
@@ -5086,6 +5082,7 @@ M:	Peter Zijlstra <a.p.zijlstra@chello.nl>
 M:	Paul Mackerras <paulus@samba.org>
 M:	Ingo Molnar <mingo@elte.hu>
 M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git perf/core
 S:	Supported
 F:	kernel/events/*
 F:	include/linux/perf_event.h
@@ -5117,6 +5114,15 @@ L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/devices/phram.c
 
+PICOXCELL SUPPORT
+M:	Jamie Iles <jamie@jamieiles.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+T:	git git://github.com/jamieiles/linux-2.6-ji.git
+S:	Supported
+F:	arch/arm/mach-picoxcell
+F:	drivers/*/picoxcell*
+F:	drivers/*/*/picoxcell*
+
 PIN CONTROL SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
@@ -5165,6 +5171,7 @@ F:	drivers/scsi/pm8001/
 
 POSIX CLOCKS and TIMERS
 M:	Thomas Gleixner <tglx@linutronix.de>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git timers/core
 S:	Supported
 F:	fs/timerfd.c
 F:	include/linux/timer*
@@ -5680,6 +5687,7 @@ F:	drivers/dma/dw_dmac.c
 TIMEKEEPING, NTP
 M:	John Stultz <johnstul@us.ibm.com>
 M:	Thomas Gleixner <tglx@linutronix.de>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git timers/core
 S:	Supported
 F:	include/linux/clocksource.h
 F:	include/linux/time.h
@@ -5704,6 +5712,7 @@ F:	drivers/watchdog/sc1200wdt.c
 SCHEDULER
 M:	Ingo Molnar <mingo@elte.hu>
 M:	Peter Zijlstra <peterz@infradead.org>
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git sched/core
 S:	Maintained
 F:	kernel/sched*
 F:	include/linux/sched.h
@@ -6631,7 +6640,7 @@ TRACING
 M:	Steven Rostedt <rostedt@goodmis.org>
 M:	Frederic Weisbecker <fweisbec@gmail.com>
 M:	Ingo Molnar <mingo@redhat.com>
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip.git perf/core
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git perf/core
 S:	Maintained
 F:	Documentation/trace/ftrace.txt
 F:	arch/*/*/*/ftrace.h
@@ -7381,7 +7390,7 @@ M:	Thomas Gleixner <tglx@linutronix.de>
 M:	Ingo Molnar <mingo@redhat.com>
 M:	"H. Peter Anvin" <hpa@zytor.com>
 M:	x86@kernel.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git x86/core
 S:	Maintained
 F:	Documentation/x86/
 F:	arch/x86/

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 2
 SUBLEVEL = 0
-EXTRAVERSION = -rc6
+EXTRAVERSION = -rc7
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -258,6 +258,7 @@ config ARCH_INTEGRATOR
 	select ARCH_HAS_CPUFREQ
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
+	select HAVE_TCM
 	select ICST
 	select GENERIC_CLOCKEVENTS
 	select PLAT_VERSATILE
@@ -341,10 +342,12 @@ config ARCH_HIGHBANK
 	select ARM_AMBA
 	select ARM_GIC
 	select ARM_TIMER_SP804
+	select CACHE_L2X0
 	select CLKDEV_LOOKUP
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU
+	select HAVE_SMP
 	select USE_OF
 	help
 	  Support for the Calxeda Highbank SoC based boards.
@@ -362,6 +365,7 @@ config ARCH_CNS3XXX
 	select CPU_V6K
 	select GENERIC_CLOCKEVENTS
 	select ARM_GIC
+	select MIGHT_HAVE_CACHE_L2X0
 	select MIGHT_HAVE_PCI
 	select PCI_DOMAINS if PCI
 	help
@@ -382,6 +386,7 @@ config ARCH_PRIMA2
 	select GENERIC_CLOCKEVENTS
 	select CLKDEV_LOOKUP
 	select GENERIC_IRQ_CHIP
+	select MIGHT_HAVE_CACHE_L2X0
 	select USE_OF
 	select ZONE_DMA
 	help
@@ -634,6 +639,8 @@ config ARCH_TEGRA
 	select GENERIC_GPIO
 	select HAVE_CLK
 	select HAVE_SCHED_CLOCK
+	select HAVE_SMP
+	select MIGHT_HAVE_CACHE_L2X0
 	select ARCH_HAS_CPUFREQ
 	help
 	  This enables support for NVIDIA Tegra based systems (Tegra APX,
@@ -651,6 +658,7 @@ config ARCH_PICOXCELL
 	select HAVE_SCHED_CLOCK
 	select HAVE_TCM
 	select NO_IOPORT
+	select SPARSE_IRQ
 	select USE_OF
 	help
 	  This enables support for systems based on the Picochip picoXcell
@@ -703,7 +711,9 @@ config ARCH_SHMOBILE
 	select HAVE_CLK
 	select CLKDEV_LOOKUP
 	select HAVE_MACH_CLKDEV
+	select HAVE_SMP
 	select GENERIC_CLOCKEVENTS
+	select MIGHT_HAVE_CACHE_L2X0
 	select NO_IOPORT
 	select SPARSE_IRQ
 	select MULTI_IRQ_HANDLER
@@ -868,16 +878,6 @@ config ARCH_SHARK
 	  Support for the StrongARM based Digital DNARD machine, also known
 	  as "Shark" (<http://www.shark-linux.de/shark.html>).
 
-config ARCH_TCC_926
-	bool "Telechips TCC ARM926-based systems"
-	select CLKSRC_MMIO
-	select CPU_ARM926T
-	select HAVE_CLK
-	select CLKDEV_LOOKUP
-	select GENERIC_CLOCKEVENTS
-	help
-	  Support for Telechips TCC ARM926-based systems.
-
 config ARCH_U300
 	bool "ST-Ericsson U300 Series"
 	depends on MMU
@@ -893,7 +893,6 @@ config ARCH_U300
 	select HAVE_MACH_CLKDEV
 	select GENERIC_GPIO
 	select ARCH_REQUIRE_GPIOLIB
-	select NEED_MACH_MEMORY_H
 	help
 	  Support for ST-Ericsson U300 series mobile platforms.
 
@@ -905,6 +904,8 @@ config ARCH_U8500
 	select CLKDEV_LOOKUP
 	select ARCH_REQUIRE_GPIOLIB
 	select ARCH_HAS_CPUFREQ
+	select HAVE_SMP
+	select MIGHT_HAVE_CACHE_L2X0
 	help
 	  Support for ST-Ericsson's Ux500 architecture
 
@@ -915,6 +916,7 @@ config ARCH_NOMADIK
 	select CPU_ARM926T
 	select CLKDEV_LOOKUP
 	select GENERIC_CLOCKEVENTS
+	select MIGHT_HAVE_CACHE_L2X0
 	select ARCH_REQUIRE_GPIOLIB
 	help
 	  Support for the Nomadik platform by ST-Ericsson
@@ -974,6 +976,7 @@ config ARCH_ZYNQ
 	select ARM_GIC
 	select ARM_AMBA
 	select ICST
+	select MIGHT_HAVE_CACHE_L2X0
 	select USE_OF
 	help
 	  Support for Xilinx Zynq ARM Cortex A9 Platform
@@ -1060,8 +1063,6 @@ source "arch/arm/plat-s5p/Kconfig"
 
 source "arch/arm/plat-spear/Kconfig"
 
-source "arch/arm/plat-tcc/Kconfig"
-
 if ARCH_S3C2410
 source "arch/arm/mach-s3c2410/Kconfig"
 source "arch/arm/mach-s3c2412/Kconfig"
@@ -1126,6 +1127,11 @@ config ARM_TIMER_SP804
 
 source arch/arm/mm/Kconfig
 
+config ARM_NR_BANKS
+	int
+	default 16 if ARCH_EP93XX
+	default 8
+
 config IWMMXT
 	bool "Enable iWMMXt support"
 	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4
@@ -1246,7 +1252,7 @@ config PL310_ERRATA_588369
 
 config ARM_ERRATA_720789
 	bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID"
-	depends on CPU_V7 && SMP
+	depends on CPU_V7
 	help
 	  This option enables the workaround for the 720789 Cortex-A9 (prior to
 	  r2p0) erratum. A faulty ASID can be sent to the other CPUs for the
@@ -1282,7 +1288,7 @@ config ARM_ERRATA_743622
 
 config ARM_ERRATA_751472
 	bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
-	depends on CPU_V7 && SMP
+	depends on CPU_V7
 	help
 	  This option enables the workaround for the 751472 Cortex-A9 (prior
 	  to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
@@ -1435,14 +1441,20 @@ menu "Kernel Features"
 
 source "kernel/time/Kconfig"
 
+config HAVE_SMP
+	bool
+	help
+	  This option should be selected by machines which have an SMP-
+	  capable CPU.
+
+	  The only effect of this option is to make the SMP-related
+	  options available to the user for configuration.
+
 config SMP
 	bool "Symmetric Multi-Processing"
 	depends on CPU_V6K || CPU_V7
 	depends on GENERIC_CLOCKEVENTS
-	depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \
-		 MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
-		 ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \
-		 ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE || ARCH_HIGHBANK || SOC_IMX6Q
+	depends on HAVE_SMP
 	depends on MMU
 	select USE_GENERIC_SMP_HELPERS
 	select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
@@ -1560,6 +1572,16 @@ config LOCAL_TIMERS
 	  accounting to be spread across the timer interval, preventing a
 	  "thundering herd" at every timer tick.
 
+config ARCH_NR_GPIO
+	int
+	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
+	default 350 if ARCH_U8500
+	default 0
+	help
+	  Maximum number of GPIOs in the system.
+
+	  If unsure, leave the default value.
+
 source kernel/Kconfig.preempt
 
 config HZ

arch/arm/Kconfig.debug

@@ -100,6 +100,14 @@ choice
 		  Note that the system will appear to hang during boot if there
 		  is nothing connected to read from the DCC.
 
+	config AT91_DEBUG_LL_DBGU0
+		bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+		depends on HAVE_AT91_DBGU0
+
+	config AT91_DEBUG_LL_DBGU1
+		bool "Kernel low-level debugging on 9263, 9g45 and cap9"
+		depends on HAVE_AT91_DBGU1
+
 	config DEBUG_FOOTBRIDGE_COM1
 		bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1"
 		depends on FOOTBRIDGE
@@ -247,6 +255,43 @@ choice
 		  their output to the standard serial port on the RealView
 		  PB1176 platform.
 
+	config DEBUG_MSM_UART1
+		bool "Kernel low-level debugging messages via MSM UART1"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the first serial port on MSM devices.
+
+	config DEBUG_MSM_UART2
+		bool "Kernel low-level debugging messages via MSM UART2"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the second serial port on MSM devices.
+
+	config DEBUG_MSM_UART3
+		bool "Kernel low-level debugging messages via MSM UART3"
+		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the third serial port on MSM devices.
+
+	config DEBUG_MSM8660_UART
+		bool "Kernel low-level debugging messages via MSM 8660 UART"
+		depends on ARCH_MSM8X60
+		select MSM_HAS_DEBUG_UART_HS
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port on MSM 8660 devices.
+
+	config DEBUG_MSM8960_UART
+		bool "Kernel low-level debugging messages via MSM 8960 UART"
+		depends on ARCH_MSM8960
+		select MSM_HAS_DEBUG_UART_HS
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to the serial port on MSM 8960 devices.
+
 endchoice
 
 config EARLY_PRINTK

arch/arm/Makefile

@@ -184,7 +184,6 @@ machine-$(CONFIG_ARCH_EXYNOS4)		:= exynos
 machine-$(CONFIG_ARCH_SA1100)		:= sa1100
 machine-$(CONFIG_ARCH_SHARK)		:= shark
 machine-$(CONFIG_ARCH_SHMOBILE) 	:= shmobile
-machine-$(CONFIG_ARCH_TCC8K)		:= tcc8k
 machine-$(CONFIG_ARCH_TEGRA)		:= tegra
 machine-$(CONFIG_ARCH_U300)		:= u300
 machine-$(CONFIG_ARCH_U8500)		:= ux500
@@ -204,7 +203,6 @@ machine-$(CONFIG_ARCH_ZYNQ)		:= zynq
 plat-$(CONFIG_ARCH_MXC)		:= mxc
 plat-$(CONFIG_ARCH_OMAP)	:= omap
 plat-$(CONFIG_ARCH_S3C64XX)	:= samsung
-plat-$(CONFIG_ARCH_TCC_926)	:= tcc
 plat-$(CONFIG_ARCH_ZYNQ)	:= versatile
 plat-$(CONFIG_PLAT_IOP)		:= iop
 plat-$(CONFIG_PLAT_NOMADIK)	:= nomadik

arch/arm/boot/compressed/Makefile

@@ -126,7 +126,8 @@ ccflags-y := -fpic -fno-builtin -I$(obj)
 asflags-y := -Wa,-march=all
 
 # Supply kernel BSS size to the decompressor via a linker symbol.
-KBSS_SZ = $(shell size $(obj)/../../../../vmlinux | awk 'END{print $$3}')
+KBSS_SZ = $(shell $(CROSS_COMPILE)size $(obj)/../../../../vmlinux | \
+		awk 'END{print $$3}')
 LDFLAGS_vmlinux = --defsym _kernel_bss_size=$(KBSS_SZ)
 # Supply ZRELADDR to the decompressor via a linker symbol.
 ifneq ($(CONFIG_AUTO_ZRELADDR),y)

arch/arm/boot/dts/exynos4210-origen.dts

@@ -0,0 +1,137 @@
+/*
+ * Samsung's Exynos4210 based Origen board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Device tree source file for Insignal's Origen board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+	model = "Insignal Origen evaluation board based on Exynos4210";
+	compatible = "insignal,origen", "samsung,exynos4210";
+
+	memory {
+		reg = <0x40000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
+	};
+
+	sdhci@12530000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk2 2 2 3 3>;
+		gpios = <&gpk2 0 2 0 3>,
+			<&gpk2 1 2 0 3>,
+			<&gpk2 3 2 3 3>,
+			<&gpk2 4 2 3 3>,
+			<&gpk2 5 2 3 3>,
+			<&gpk2 6 2 3 3>;
+	};
+
+	sdhci@12510000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk0 2 2 3 3>;
+		gpios = <&gpk0 0 2 0 3>,
+			<&gpk0 1 2 0 3>,
+			<&gpk0 3 2 3 3>,
+			<&gpk0 4 2 3 3>,
+			<&gpk0 5 2 3 3>,
+			<&gpk0 6 2 3 3>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		up {
+			label = "Up";
+			gpios = <&gpx2 0 0 0 2>;
+			linux,code = <103>;
+		};
+
+		down {
+			label = "Down";
+			gpios = <&gpx2 1 0 0 2>;
+			linux,code = <108>;
+		};
+
+		back {
+			label = "Back";
+			gpios = <&gpx1 7 0 0 2>;
+			linux,code = <158>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&gpx1 6 0 0 2>;
+			linux,code = <102>;
+		};
+
+		menu {
+			label = "Menu";
+			gpios = <&gpx1 5 0 0 2>;
+			linux,code = <139>;
+		};
+	};
+
+	keypad@100A0000 {
+		status = "disabled";
+	};
+
+	sdhci@12520000 {
+		status = "disabled";
+	};
+
+	sdhci@12540000 {
+		status = "disabled";
+	};
+
+	i2c@13860000 {
+		status = "disabled";
+	};
+
+	i2c@13870000 {
+		status = "disabled";
+	};
+
+	i2c@13880000 {
+		status = "disabled";
+	};
+
+	i2c@13890000 {
+		status = "disabled";
+	};
+
+	i2c@138A0000 {
+		status = "disabled";
+	};
+
+	i2c@138B0000 {
+		status = "disabled";
+	};
+
+	i2c@138C0000 {
+		status = "disabled";
+	};
+
+	i2c@138D0000 {
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -0,0 +1,182 @@
+/*
+ * Samsung's Exynos4210 based SMDKV310 board device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Device tree source file for Samsung's SMDKV310 board which is based on
+ * Samsung's Exynos4210 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos4210.dtsi"
+
+/ {
+	model = "Samsung smdkv310 evaluation board based on Exynos4210";
+	compatible = "samsung,smdkv310", "samsung,exynos4210";
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
+	};
+
+	sdhci@12530000 {
+		samsung,sdhci-bus-width = <4>;
+		linux,mmc_cap_4_bit_data;
+		samsung,sdhci-cd-internal;
+		gpio-cd = <&gpk2 2 2 3 3>;
+		gpios = <&gpk2 0 2 0 3>,
+			<&gpk2 1 2 0 3>,
+			<&gpk2 3 2 3 3>,
+			<&gpk2 4 2 3 3>,
+			<&gpk2 5 2 3 3>,
+			<&gpk2 6 2 3 3>;
+	};
+
+	keypad@100A0000 {
+		samsung,keypad-num-rows = <2>;
+		samsung,keypad-num-columns = <8>;
+		linux,keypad-no-autorepeat;
+		linux,keypad-wakeup;
+
+		row-gpios = <&gpx2 0 3 3 0>,
+			    <&gpx2 1 3 3 0>;
+
+		col-gpios = <&gpx1 0 3 0 0>,
+			    <&gpx1 1 3 0 0>,
+			    <&gpx1 2 3 0 0>,
+			    <&gpx1 3 3 0 0>,
+			    <&gpx1 4 3 0 0>,
+			    <&gpx1 5 3 0 0>,
+			    <&gpx1 6 3 0 0>,
+			    <&gpx1 7 3 0 0>;
+
+		key_1 {
+			keypad,row = <0>;
+			keypad,column = <3>;
+			linux,code = <2>;
+		};
+
+		key_2 {
+			keypad,row = <0>;
+			keypad,column = <4>;
+			linux,code = <3>;
+		};
+
+		key_3 {
+			keypad,row = <0>;
+			keypad,column = <5>;
+			linux,code = <4>;
+		};
+
+		key_4 {
+			keypad,row = <0>;
+			keypad,column = <6>;
+			linux,code = <5>;
+		};
+
+		key_5 {
+			keypad,row = <0>;
+			keypad,column = <7>;
+			linux,code = <6>;
+		};
+
+		key_a {
+			keypad,row = <1>;
+			keypad,column = <3>;
+			linux,code = <30>;
+		};
+
+		key_b {
+			keypad,row = <1>;
+			keypad,column = <4>;
+			linux,code = <48>;
+		};
+
+		key_c {
+			keypad,row = <1>;
+			keypad,column = <5>;
+			linux,code = <46>;
+		};
+
+		key_d {
+			keypad,row = <1>;
+			keypad,column = <6>;
+			linux,code = <32>;
+		};
+
+		key_e {
+			keypad,row = <1>;
+			keypad,column = <7>;
+			linux,code = <18>;
+		};
+	};
+
+	i2c@13860000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <20000>;
+		gpios = <&gpd1 0 2 3 0>,
+			<&gpd1 1 2 3 0>;
+
+		eeprom@50 {
+			compatible = "samsung,24ad0xd1";
+			reg = <0x50>;
+		};
+
+		eeprom@52 {
+			compatible = "samsung,24ad0xd1";
+			reg = <0x52>;
+		};
+	};
+
+	sdhci@12510000 {
+		status = "disabled";
+	};
+
+	sdhci@12520000 {
+		status = "disabled";
+	};
+
+	sdhci@12540000 {
+		status = "disabled";
+	};
+
+	i2c@13870000 {
+		status = "disabled";
+	};
+
+	i2c@13880000 {
+		status = "disabled";
+	};
+
+	i2c@13890000 {
+		status = "disabled";
+	};
+
+	i2c@138A0000 {
+		status = "disabled";
+	};
+
+	i2c@138B0000 {
+		status = "disabled";
+	};
+
+	i2c@138C0000 {
+		status = "disabled";
+	};
+
+	i2c@138D0000 {
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/exynos4210.dtsi

@@ -0,0 +1,397 @@
+/*
+ * Samsung's Exynos4210 SoC device tree source
+ *
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2010-2011 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Samsung's Exynos4210 SoC device nodes are listed in this file. Exynos4210
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos4210 SoC. As device tree coverage for Exynos4210 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "samsung,exynos4210";
+	interrupt-parent = <&gic>;
+
+	gic:interrupt-controller@10490000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
+	};
+
+	watchdog@10060000 {
+		compatible = "samsung,s3c2410-wdt";
+		reg = <0x10060000 0x100>;
+		interrupts = <0 43 0>;
+	};
+
+	rtc@10070000 {
+		compatible = "samsung,s3c6410-rtc";
+		reg = <0x10070000 0x100>;
+		interrupts = <0 44 0>, <0 45 0>;
+	};
+
+	keypad@100A0000 {
+		compatible = "samsung,s5pv210-keypad";
+		reg = <0x100A0000 0x100>;
+		interrupts = <0 109 0>;
+	};
+
+	sdhci@12510000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12510000 0x100>;
+		interrupts = <0 73 0>;
+	};
+
+	sdhci@12520000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12520000 0x100>;
+		interrupts = <0 74 0>;
+	};
+
+	sdhci@12530000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12530000 0x100>;
+		interrupts = <0 75 0>;
+	};
+
+	sdhci@12540000 {
+		compatible = "samsung,exynos4210-sdhci";
+		reg = <0x12540000 0x100>;
+		interrupts = <0 76 0>;
+	};
+
+	serial@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+	};
+
+	serial@13810000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13810000 0x100>;
+		interrupts = <0 53 0>;
+	};
+
+	serial@13820000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13820000 0x100>;
+		interrupts = <0 54 0>;
+	};
+
+	serial@13830000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13830000 0x100>;
+		interrupts = <0 55 0>;
+	};
+
+	i2c@13860000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13860000 0x100>;
+		interrupts = <0 58 0>;
+	};
+
+	i2c@13870000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13870000 0x100>;
+		interrupts = <0 59 0>;
+	};
+
+	i2c@13880000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13880000 0x100>;
+		interrupts = <0 60 0>;
+	};
+
+	i2c@13890000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13890000 0x100>;
+		interrupts = <0 61 0>;
+	};
+
+	i2c@138A0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138A0000 0x100>;
+		interrupts = <0 62 0>;
+	};
+
+	i2c@138B0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138B0000 0x100>;
+		interrupts = <0 63 0>;
+	};
+
+	i2c@138C0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138C0000 0x100>;
+		interrupts = <0 64 0>;
+	};
+
+	i2c@138D0000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x138D0000 0x100>;
+		interrupts = <0 65 0>;
+	};
+
+	amba {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,amba-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		pdma0: pdma@12680000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12680000 0x1000>;
+			interrupts = <0 35 0>;
+		};
+
+		pdma1: pdma@12690000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x12690000 0x1000>;
+			interrupts = <0 36 0>;
+		};
+	};
+
+	gpio-controllers {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		gpio-controller;
+		ranges;
+
+		gpa0: gpio-controller@11400000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400000 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpa1: gpio-controller@11400020 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400020 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpb: gpio-controller@11400040 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400040 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpc0: gpio-controller@11400060 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400060 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpc1: gpio-controller@11400080 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400080 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpd0: gpio-controller@114000A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpd1: gpio-controller@114000C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe0: gpio-controller@114000E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114000E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe1: gpio-controller@11400100 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400100 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe2: gpio-controller@11400120 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400120 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe3: gpio-controller@11400140 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400140 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpe4: gpio-controller@11400160 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400160 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf0: gpio-controller@11400180 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11400180 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf1: gpio-controller@114001A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf2: gpio-controller@114001C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpf3: gpio-controller@114001E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x114001E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpj0: gpio-controller@11000000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000000 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpj1: gpio-controller@11000020 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000020 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk0: gpio-controller@11000040 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000040 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk1: gpio-controller@11000060 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000060 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk2: gpio-controller@11000080 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000080 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpk3: gpio-controller@110000A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl0: gpio-controller@110000C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl1: gpio-controller@110000E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110000E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpl2: gpio-controller@11000100 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000100 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy0: gpio-controller@11000120 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000120 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy1: gpio-controller@11000140 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000140 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy2: gpio-controller@11000160 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000160 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy3: gpio-controller@11000180 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000180 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy4: gpio-controller@110001A0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001A0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy5: gpio-controller@110001C0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001C0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpy6: gpio-controller@110001E0 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x110001E0 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx0: gpio-controller@11000C00 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C00 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx1: gpio-controller@11000C20 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C20 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx2: gpio-controller@11000C40 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C40 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpx3: gpio-controller@11000C60 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x11000C60 0x20>;
+			#gpio-cells = <4>;
+		};
+
+		gpz: gpio-controller@03860000 {
+			compatible = "samsung,exynos4-gpio";
+			reg = <0x03860000 0x20>;
+			#gpio-cells = <4>;
+		};
+	};
+};

arch/arm/common/pl330.c

@@ -221,17 +221,6 @@
  */
 #define MCODE_BUFF_PER_REQ	256
 
-/*
- * Mark a _pl330_req as free.
- * We do it by writing DMAEND as the first instruction
- * because no valid request is going to have DMAEND as
- * its first instruction to execute.
- */
-#define MARK_FREE(req)	do { \
-				_emit_END(0, (req)->mc_cpu); \
-				(req)->mc_len = 0; \
-			} while (0)
-
 /* If the _pl330_req is available to the client */
 #define IS_FREE(req)	(*((u8 *)((req)->mc_cpu)) == CMD_DMAEND)
 
@@ -301,8 +290,10 @@ struct pl330_thread {
 	struct pl330_dmac *dmac;
 	/* Only two at a time */
 	struct _pl330_req req[2];
-	/* Index of the last submitted request */
+	/* Index of the last enqueued request */
 	unsigned lstenq;
+	/* Index of the last submitted request or -1 if the DMA is stopped */
+	int req_running;
 };
 
 enum pl330_dmac_state {
@@ -778,6 +769,22 @@ static inline void _execute_DBGINSN(struct pl330_thread *thrd,
 	writel(0, regs + DBGCMD);
 }
 
+/*
+ * Mark a _pl330_req as free.
+ * We do it by writing DMAEND as the first instruction
+ * because no valid request is going to have DMAEND as
+ * its first instruction to execute.
+ */
+static void mark_free(struct pl330_thread *thrd, int idx)
+{
+	struct _pl330_req *req = &thrd->req[idx];
+
+	_emit_END(0, req->mc_cpu);
+	req->mc_len = 0;
+
+	thrd->req_running = -1;
+}
+
 static inline u32 _state(struct pl330_thread *thrd)
 {
 	void __iomem *regs = thrd->dmac->pinfo->base;
@@ -836,31 +843,6 @@ static inline u32 _state(struct pl330_thread *thrd)
 	}
 }
 
-/* If the request 'req' of thread 'thrd' is currently active */
-static inline bool _req_active(struct pl330_thread *thrd,
-		struct _pl330_req *req)
-{
-	void __iomem *regs = thrd->dmac->pinfo->base;
-	u32 buf = req->mc_bus, pc = readl(regs + CPC(thrd->id));
-
-	if (IS_FREE(req))
-		return false;
-
-	return (pc >= buf && pc <= buf + req->mc_len) ? true : false;
-}
-
-/* Returns 0 if the thread is inactive, ID of active req + 1 otherwise */
-static inline unsigned _thrd_active(struct pl330_thread *thrd)
-{
-	if (_req_active(thrd, &thrd->req[0]))
-		return 1; /* First req active */
-
-	if (_req_active(thrd, &thrd->req[1]))
-		return 2; /* Second req active */
-
-	return 0;
-}
-
 static void _stop(struct pl330_thread *thrd)
 {
 	void __iomem *regs = thrd->dmac->pinfo->base;
@@ -892,17 +874,22 @@ static bool _trigger(struct pl330_thread *thrd)
 	struct _arg_GO go;
 	unsigned ns;
 	u8 insn[6] = {0, 0, 0, 0, 0, 0};
+	int idx;
 
 	/* Return if already ACTIVE */
 	if (_state(thrd) != PL330_STATE_STOPPED)
 		return true;
 
-	if (!IS_FREE(&thrd->req[1 - thrd->lstenq]))
-		req = &thrd->req[1 - thrd->lstenq];
-	else if (!IS_FREE(&thrd->req[thrd->lstenq]))
-		req = &thrd->req[thrd->lstenq];
-	else
-		req = NULL;
+	idx = 1 - thrd->lstenq;
+	if (!IS_FREE(&thrd->req[idx]))
+		req = &thrd->req[idx];
+	else {
+		idx = thrd->lstenq;
+		if (!IS_FREE(&thrd->req[idx]))
+			req = &thrd->req[idx];
+		else
+			req = NULL;
+	}
 
 	/* Return if no request */
 	if (!req || !req->r)
@@ -933,6 +920,8 @@ static bool _trigger(struct pl330_thread *thrd)
 	/* Only manager can execute GO */
 	_execute_DBGINSN(thrd, insn, true);
 
+	thrd->req_running = idx;
+
 	return true;
 }
 
@@ -1382,8 +1371,8 @@ static void pl330_dotask(unsigned long data)
 
 			thrd->req[0].r = NULL;
 			thrd->req[1].r = NULL;
-			MARK_FREE(&thrd->req[0]);
-			MARK_FREE(&thrd->req[1]);
+			mark_free(thrd, 0);
+			mark_free(thrd, 1);
 
 			/* Clear the reset flag */
 			pl330->dmac_tbd.reset_chan &= ~(1 << i);
@@ -1461,14 +1450,12 @@ int pl330_update(const struct pl330_info *pi)
 
 			thrd = &pl330->channels[id];
 
-			active = _thrd_active(thrd);
-			if (!active) /* Aborted */
+			active = thrd->req_running;
+			if (active == -1) /* Aborted */
 				continue;
 
-			active -= 1;
-
 			rqdone = &thrd->req[active];
-			MARK_FREE(rqdone);
+			mark_free(thrd, active);
 
 			/* Get going again ASAP */
 			_start(thrd);
@@ -1480,13 +1467,19 @@ int pl330_update(const struct pl330_info *pi)
 
 	/* Now that we are in no hurry, do the callbacks */
 	while (!list_empty(&pl330->req_done)) {
+		struct pl330_req *r;
+
 		rqdone = container_of(pl330->req_done.next,
 					struct _pl330_req, rqd);
 
 		list_del_init(&rqdone->rqd);
 
+		/* Detach the req */
+		r = rqdone->r;
+		rqdone->r = NULL;
+
 		spin_unlock_irqrestore(&pl330->lock, flags);
-		_callback(rqdone->r, PL330_ERR_NONE);
+		_callback(r, PL330_ERR_NONE);
 		spin_lock_irqsave(&pl330->lock, flags);
 	}
 
@@ -1509,7 +1502,7 @@ int pl330_chan_ctrl(void *ch_id, enum pl330_chan_op op)
 	struct pl330_thread *thrd = ch_id;
 	struct pl330_dmac *pl330;
 	unsigned long flags;
-	int ret = 0, active;
+	int ret = 0, active = thrd->req_running;
 
 	if (!thrd || thrd->free || thrd->dmac->state == DYING)
 		return -EINVAL;
@@ -1525,28 +1518,24 @@ int pl330_chan_ctrl(void *ch_id, enum pl330_chan_op op)
 
 		thrd->req[0].r = NULL;
 		thrd->req[1].r = NULL;
-		MARK_FREE(&thrd->req[0]);
-		MARK_FREE(&thrd->req[1]);
+		mark_free(thrd, 0);
+		mark_free(thrd, 1);
 		break;
 
 	case PL330_OP_ABORT:
-		active = _thrd_active(thrd);
-
 		/* Make sure the channel is stopped */
 		_stop(thrd);
 
 		/* ABORT is only for the active req */
-		if (!active)
+		if (active == -1)
 			break;
 
-		active--;
-
 		thrd->req[active].r = NULL;
-		MARK_FREE(&thrd->req[active]);
+		mark_free(thrd, active);
 
 		/* Start the next */
 	case PL330_OP_START:
-		if (!_thrd_active(thrd) && !_start(thrd))
+		if ((active == -1) && !_start(thrd))
 			ret = -EIO;
 		break;
 
@@ -1587,14 +1576,13 @@ int pl330_chan_status(void *ch_id, struct pl330_chanstatus *pstatus)
 	else
 		pstatus->faulting = false;
 
-	active = _thrd_active(thrd);
+	active = thrd->req_running;
 
-	if (!active) {
+	if (active == -1) {
 		/* Indicate that the thread is not running */
 		pstatus->top_req = NULL;
 		pstatus->wait_req = NULL;
 	} else {
-		active--;
 		pstatus->top_req = thrd->req[active].r;
 		pstatus->wait_req = !IS_FREE(&thrd->req[1 - active])
 					? thrd->req[1 - active].r : NULL;
@@ -1659,9 +1647,9 @@ void *pl330_request_channel(const struct pl330_info *pi)
 				thrd->free = false;
 				thrd->lstenq = 1;
 				thrd->req[0].r = NULL;
-				MARK_FREE(&thrd->req[0]);
+				mark_free(thrd, 0);
 				thrd->req[1].r = NULL;
-				MARK_FREE(&thrd->req[1]);
+				mark_free(thrd, 1);
 				break;
 			}
 		}
@@ -1767,14 +1755,14 @@ static inline void _reset_thread(struct pl330_thread *thrd)
 	thrd->req[0].mc_bus = pl330->mcode_bus
 				+ (thrd->id * pi->mcbufsz);
 	thrd->req[0].r = NULL;
-	MARK_FREE(&thrd->req[0]);
+	mark_free(thrd, 0);
 
 	thrd->req[1].mc_cpu = thrd->req[0].mc_cpu
 				+ pi->mcbufsz / 2;
 	thrd->req[1].mc_bus = thrd->req[0].mc_bus
 				+ pi->mcbufsz / 2;
 	thrd->req[1].r = NULL;
-	MARK_FREE(&thrd->req[1]);
+	mark_free(thrd, 1);
 }
 
 static int dmac_alloc_threads(struct pl330_dmac *pl330)

arch/arm/common/timer-sp.c

@@ -143,7 +143,6 @@ static int sp804_set_next_event(unsigned long next,
 }
 
 static struct clock_event_device sp804_clockevent = {
-	.shift		= 32,
 	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
 	.set_mode	= sp804_set_mode,
 	.set_next_event	= sp804_set_next_event,
@@ -169,13 +168,9 @@ void __init sp804_clockevents_init(void __iomem *base, unsigned int irq,
 
 	clkevt_base = base;
 	clkevt_reload = DIV_ROUND_CLOSEST(rate, HZ);
-
 	evt->name = name;
 	evt->irq = irq;
-	evt->mult = div_sc(rate, NSEC_PER_SEC, evt->shift);
-	evt->max_delta_ns = clockevent_delta2ns(0xffffffff, evt);
-	evt->min_delta_ns = clockevent_delta2ns(0xf, evt);
 
 	setup_irq(irq, &sp804_timer_irq);
-	clockevents_register_device(evt);
+	clockevents_config_and_register(evt, rate, 0xf, 0xffffffff);
 }

arch/arm/common/vic.c

@@ -197,8 +197,8 @@ static void __init vic_register(void __iomem *base, unsigned int irq,
 	v->domain.nr_irq = 32;
 #ifdef CONFIG_OF_IRQ
 	v->domain.of_node = of_node_get(node);
-	v->domain.ops = &irq_domain_simple_ops;
 #endif /* CONFIG_OF */
+	v->domain.ops = &irq_domain_simple_ops;
 	irq_domain_add(&v->domain);
 }
 

arch/arm/configs/imx_v4_v5_defconfig

@@ -18,9 +18,10 @@ CONFIG_ARCH_MXC=y
 CONFIG_ARCH_IMX_V4_V5=y
 CONFIG_ARCH_MX1ADS=y
 CONFIG_MACH_SCB9328=y
+CONFIG_MACH_APF9328=y
 CONFIG_MACH_MX21ADS=y
 CONFIG_MACH_MX25_3DS=y
-CONFIG_MACH_EUKREA_CPUIMX25=y
+CONFIG_MACH_EUKREA_CPUIMX25SD=y
 CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_PCM038=y
 CONFIG_MACH_CPUIMX27=y
@@ -71,17 +72,16 @@ CONFIG_MTD_CFI_GEOMETRY=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_MXC=y
 CONFIG_MTD_UBI=y
 CONFIG_MISC_DEVICES=y
 CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
 CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
 CONFIG_DM9000=y
+CONFIG_SMC91X=y
 CONFIG_SMC911X=y
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
+CONFIG_SMSC_PHY=y
 # CONFIG_INPUT_MOUSEDEV is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_KEYBOARD is not set
@@ -99,6 +99,7 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_IMX=y
 CONFIG_SPI=y
 CONFIG_SPI_IMX=y
+CONFIG_SPI_SPIDEV=y
 CONFIG_W1=y
 CONFIG_W1_MASTER_MXC=y
 CONFIG_W1_SLAVE_THERM=y
@@ -138,6 +139,7 @@ CONFIG_MMC=y
 CONFIG_MMC_MXC=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_MC13783=y
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=y

arch/arm/configs/pcontrol_g20_defconfig

@@ -1,175 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_CROSS_COMPILE="/opt/arm-2010q1/bin/arm-none-linux-gnueabi-"
-# CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_TREE_PREEMPT_RCU=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_NAMESPACES=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-# CONFIG_KALLSYMS is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_LBDAF is not set
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_DEFAULT_DEADLINE=y
-CONFIG_ARCH_AT91=y
-CONFIG_ARCH_AT91SAM9G20=y
-CONFIG_MACH_PCONTROL_G20=y
-CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 mem=128M mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) root=/dev/mmcblk0p1 rootwait rw"
-CONFIG_VFP=y
-CONFIG_BINFMT_MISC=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_VLAN_8021Q=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_PHRAM=m
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ATMEL=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_ATMEL_TCLIB=y
-CONFIG_EEPROM_AT24=m
-CONFIG_SCSI=m
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=m
-CONFIG_SCSI_MULTI_LUN=y
-# CONFIG_SCSI_LOWLEVEL is not set
-CONFIG_NETDEVICES=y
-CONFIG_MACVLAN=m
-CONFIG_TUN=m
-CONFIG_SMSC_PHY=m
-CONFIG_BROADCOM_PHY=m
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MACB=y
-CONFIG_SMSC911X=m
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_WLAN is not set
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_MPPE=m
-CONFIG_INPUT_POLLDEV=y
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=m
-CONFIG_KEYBOARD_MATRIX=m
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=m
-CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-# CONFIG_SERIO is not set
-# CONFIG_DEVKMEM is not set
-CONFIG_SERIAL_ATMEL=y
-CONFIG_SERIAL_ATMEL_CONSOLE=y
-CONFIG_SERIAL_MAX3100=m
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-CONFIG_R3964=m
-CONFIG_I2C=m
-CONFIG_I2C_CHARDEV=m
-# CONFIG_I2C_HELPER_AUTO is not set
-CONFIG_I2C_GPIO=m
-CONFIG_SPI=y
-CONFIG_SPI_ATMEL=m
-CONFIG_SPI_SPIDEV=m
-CONFIG_GPIO_SYSFS=y
-CONFIG_W1=m
-CONFIG_W1_MASTER_GPIO=m
-CONFIG_W1_SLAVE_DS2431=m
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_AT91SAM9X_WATCHDOG=y
-# CONFIG_MFD_SUPPORT is not set
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_STORAGE=m
-CONFIG_USB_LIBUSUAL=y
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_GADGET=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_ETH=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_USB_G_HID=m
-CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
-CONFIG_MMC_ATMELMCI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_AT91SAM9=y
-CONFIG_AUXDISPLAY=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV=y
-CONFIG_STAGING=y
-# CONFIG_STAGING_EXCLUDE_BUILD is not set
-CONFIG_IIO=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_NLS_UTF8=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_CCITT=y

arch/arm/include/asm/bug.h

@@ -32,7 +32,6 @@
 
 #define __BUG(__file, __line, __value)				\
 do {								\
-	BUILD_BUG_ON(sizeof(struct bug_entry) != 12);		\
 	asm volatile("1:\t" BUG_INSTR_TYPE #__value "\n"	\
 		".pushsection .rodata.str, \"aMS\", %progbits, 1\n" \
 		"2:\t.asciz " #__file "\n" 			\

arch/arm/include/asm/edac.h

@@ -0,0 +1,48 @@
+/*
+ * Copyright 2011 Calxeda, Inc.
+ * Based on PPC version Copyright 2007 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef ASM_EDAC_H
+#define ASM_EDAC_H
+/*
+ * ECC atomic, DMA, SMP and interrupt safe scrub function.
+ * Implements the per arch atomic_scrub() that EDAC use for software
+ * ECC scrubbing.  It reads memory and then writes back the original
+ * value, allowing the hardware to detect and correct memory errors.
+ */
+static inline void atomic_scrub(void *va, u32 size)
+{
+#if __LINUX_ARM_ARCH__ >= 6
+	unsigned int *virt_addr = va;
+	unsigned int temp, temp2;
+	unsigned int i;
+
+	for (i = 0; i < size / sizeof(*virt_addr); i++, virt_addr++) {
+		/* Very carefully read and write to memory atomically
+		 * so we are interrupt, DMA and SMP safe.
+		 */
+		__asm__ __volatile__("\n"
+			"1:	ldrex	%0, [%2]\n"
+			"	strex	%1, %0, [%2]\n"
+			"	teq	%1, #0\n"
+			"	bne	1b\n"
+			: "=&r"(temp), "=&r"(temp2)
+			: "r"(virt_addr)
+			: "cc");
+	}
+#endif
+}
+
+#endif

arch/arm/include/asm/gpio.h

@@ -1,6 +1,10 @@
 #ifndef _ARCH_ARM_GPIO_H
 #define _ARCH_ARM_GPIO_H
 
+#if CONFIG_ARCH_NR_GPIO > 0
+#define ARCH_NR_GPIO CONFIG_ARCH_NR_GPIO
+#endif
+
 /* not all ARM platforms necessarily support this API ... */
 #include <mach/gpio.h>
 

arch/arm/include/asm/hardirq.h

@@ -27,23 +27,6 @@ u64 smp_irq_stat_cpu(unsigned int cpu);
 
 #define arch_irq_stat_cpu	smp_irq_stat_cpu
 
-#if NR_IRQS > 512
-#define HARDIRQ_BITS	10
-#elif NR_IRQS > 256
-#define HARDIRQ_BITS	9
-#else
-#define HARDIRQ_BITS	8
-#endif
-
-/*
- * The hardirq mask has to be large enough to have space
- * for potentially all IRQ sources in the system nesting
- * on a single CPU:
- */
-#if (1 << HARDIRQ_BITS) < NR_IRQS
-# error HARDIRQ_BITS is too low!
-#endif
-
 #define __ARCH_IRQ_EXIT_IRQS_DISABLED	1
 
 #endif /* __ASM_HARDIRQ_H */

arch/arm/include/asm/hardware/iop3xx.h

@@ -234,6 +234,7 @@ extern int iop3xx_get_init_atu(void);
 void iop3xx_map_io(void);
 void iop_init_cp6_handler(void);
 void iop_init_time(unsigned long tickrate);
+void iop3xx_restart(char, const char *);
 
 static inline u32 read_tmr0(void)
 {

arch/arm/include/asm/opcodes.h

@@ -0,0 +1,20 @@
+/*
+ *  arch/arm/include/asm/opcodes.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARM_OPCODES_H
+#define __ASM_ARM_OPCODES_H
+
+#ifndef __ASSEMBLY__
+extern asmlinkage unsigned int arm_check_condition(u32 opcode, u32 psr);
+#endif
+
+#define ARM_OPCODE_CONDTEST_FAIL   0
+#define ARM_OPCODE_CONDTEST_PASS   1
+#define ARM_OPCODE_CONDTEST_UNCOND 2
+
+#endif /* __ASM_ARM_OPCODES_H */

arch/arm/include/asm/pgtable.h

@@ -42,13 +42,6 @@
 #define VMALLOC_START		(((unsigned long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1))
 #define VMALLOC_END		0xff000000UL
 
-/* This is a temporary hack until shmobile's DMA area size is sorted out */
-#ifdef CONFIG_ARCH_SHMOBILE
-#warning "SH-Mobile's consistent DMA size conflicts with VMALLOC_END by 144MB"
-#undef VMALLOC_END
-#define VMALLOC_END		0xF6000000UL
-#endif
-
 #define LIBRARY_TEXT_START	0x0c000000
 
 #ifndef __ASSEMBLY__
@@ -306,6 +299,7 @@ static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
  * We provide our own arch_get_unmapped_area to cope with VIPT caches.
  */
 #define HAVE_ARCH_UNMAPPED_AREA
+#define HAVE_ARCH_UNMAPPED_AREA_TOPDOWN
 
 /*
  * remap a physical page `pfn' of size `size' with page protection `prot'

arch/arm/include/asm/processor.h

@@ -123,6 +123,8 @@ static inline void prefetch(const void *ptr)
 
 #endif
 
+#define HAVE_ARCH_PICK_MMAP_LAYOUT
+
 #endif
 
 #endif /* __ASM_ARM_PROCESSOR_H */

arch/arm/include/asm/sched_clock.h

@@ -8,113 +8,7 @@
 #ifndef ASM_SCHED_CLOCK
 #define ASM_SCHED_CLOCK
 
-#include <linux/kernel.h>
-#include <linux/types.h>
-
-struct clock_data {
-	u64 epoch_ns;
-	u32 epoch_cyc;
-	u32 epoch_cyc_copy;
-	u32 mult;
-	u32 shift;
-};
-
-#define DEFINE_CLOCK_DATA(name)	struct clock_data name
-
-static inline u64 cyc_to_ns(u64 cyc, u32 mult, u32 shift)
-{
-	return (cyc * mult) >> shift;
-}
-
-/*
- * Atomically update the sched_clock epoch.  Your update callback will
- * be called from a timer before the counter wraps - read the current
- * counter value, and call this function to safely move the epochs
- * forward.  Only use this from the update callback.
- */
-static inline void update_sched_clock(struct clock_data *cd, u32 cyc, u32 mask)
-{
-	unsigned long flags;
-	u64 ns = cd->epoch_ns +
-		cyc_to_ns((cyc - cd->epoch_cyc) & mask, cd->mult, cd->shift);
-
-	/*
-	 * Write epoch_cyc and epoch_ns in a way that the update is
-	 * detectable in cyc_to_fixed_sched_clock().
-	 */
-	raw_local_irq_save(flags);
-	cd->epoch_cyc = cyc;
-	smp_wmb();
-	cd->epoch_ns = ns;
-	smp_wmb();
-	cd->epoch_cyc_copy = cyc;
-	raw_local_irq_restore(flags);
-}
-
-/*
- * If your clock rate is known at compile time, using this will allow
- * you to optimize the mult/shift loads away.  This is paired with
- * init_fixed_sched_clock() to ensure that your mult/shift are correct.
- */
-static inline unsigned long long cyc_to_fixed_sched_clock(struct clock_data *cd,
-	u32 cyc, u32 mask, u32 mult, u32 shift)
-{
-	u64 epoch_ns;
-	u32 epoch_cyc;
-
-	/*
-	 * Load the epoch_cyc and epoch_ns atomically.  We do this by
-	 * ensuring that we always write epoch_cyc, epoch_ns and
-	 * epoch_cyc_copy in strict order, and read them in strict order.
-	 * If epoch_cyc and epoch_cyc_copy are not equal, then we're in
-	 * the middle of an update, and we should repeat the load.
-	 */
-	do {
-		epoch_cyc = cd->epoch_cyc;
-		smp_rmb();
-		epoch_ns = cd->epoch_ns;
-		smp_rmb();
-	} while (epoch_cyc != cd->epoch_cyc_copy);
-
-	return epoch_ns + cyc_to_ns((cyc - epoch_cyc) & mask, mult, shift);
-}
-
-/*
- * Otherwise, you need to use this, which will obtain the mult/shift
- * from the clock_data structure.  Use init_sched_clock() with this.
- */
-static inline unsigned long long cyc_to_sched_clock(struct clock_data *cd,
-	u32 cyc, u32 mask)
-{
-	return cyc_to_fixed_sched_clock(cd, cyc, mask, cd->mult, cd->shift);
-}
-
-/*
- * Initialize the clock data - calculate the appropriate multiplier
- * and shift.  Also setup a timer to ensure that the epoch is refreshed
- * at the appropriate time interval, which will call your update
- * handler.
- */
-void init_sched_clock(struct clock_data *, void (*)(void),
-	unsigned int, unsigned long);
-
-/*
- * Use this initialization function rather than init_sched_clock() if
- * you're using cyc_to_fixed_sched_clock, which will warn if your
- * constants are incorrect.
- */
-static inline void init_fixed_sched_clock(struct clock_data *cd,
-	void (*update)(void), unsigned int bits, unsigned long rate,
-	u32 mult, u32 shift)
-{
-	init_sched_clock(cd, update, bits, rate);
-	if (cd->mult != mult || cd->shift != shift) {
-		pr_crit("sched_clock: wrong multiply/shift: %u>>%u vs calculated %u>>%u\n"
-			"sched_clock: fix multiply/shift to avoid scheduler hiccups\n",
-			mult, shift, cd->mult, cd->shift);
-	}
-}
-
 extern void sched_clock_postinit(void);
+extern void setup_sched_clock(u32 (*read)(void), int bits, unsigned long rate);
 
 #endif

arch/arm/include/asm/setup.h

@@ -192,11 +192,7 @@ static const struct tagtable __tagtable_##fn __tag = { tag, fn }
 /*
  * Memory map description
  */
-#ifdef CONFIG_ARCH_EP93XX
-# define NR_BANKS 16
-#else
-# define NR_BANKS 8
-#endif
+#define NR_BANKS	CONFIG_ARM_NR_BANKS
 
 struct membank {
 	phys_addr_t start;

arch/arm/include/asm/swab.h

@@ -24,12 +24,13 @@
 
 #if defined(__KERNEL__) && __LINUX_ARM_ARCH__ >= 6
 
-static inline __attribute_const__ __u16 __arch_swab16(__u16 x)
+static inline __attribute_const__ __u32 __arch_swahb32(__u32 x)
 {
 	__asm__ ("rev16 %0, %1" : "=r" (x) : "r" (x));
 	return x;
 }
-#define __arch_swab16 __arch_swab16
+#define __arch_swahb32 __arch_swahb32
+#define __arch_swab16(x) ((__u16)__arch_swahb32(x))
 
 static inline __attribute_const__ __u32 __arch_swab32(__u32 x)
 {

arch/arm/include/asm/system.h

@@ -108,7 +108,6 @@ extern void __show_regs(struct pt_regs *);
 extern int __pure cpu_architecture(void);
 extern void cpu_init(void);
 
-void arm_machine_restart(char mode, const char *cmd);
 void soft_restart(unsigned long);
 extern void (*arm_pm_restart)(char str, const char *cmd);
 

arch/arm/kernel/Makefile

@@ -13,7 +13,7 @@ CFLAGS_REMOVE_return_address.o = -pg
 
 # Object file lists.
 
-obj-y		:= elf.o entry-armv.o entry-common.o irq.o \
+obj-y		:= elf.o entry-armv.o entry-common.o irq.o opcodes.o \
 		   process.o ptrace.o return_address.o setup.o signal.o \
 		   sys_arm.o stacktrace.o time.o traps.o
 

arch/arm/kernel/kprobes-test.c

@@ -202,6 +202,8 @@
 #include <linux/slab.h>
 #include <linux/kprobes.h>
 
+#include <asm/opcodes.h>
+
 #include "kprobes.h"
 #include "kprobes-test.h"
 
@@ -1050,65 +1052,9 @@ static int test_instance;
 
 static unsigned long test_check_cc(int cc, unsigned long cpsr)
 {
-	unsigned long temp;
-
-	switch (cc) {
-	case 0x0: /* eq */
-		return cpsr & PSR_Z_BIT;
-
-	case 0x1: /* ne */
-		return (~cpsr) & PSR_Z_BIT;
-
-	case 0x2: /* cs */
-		return cpsr & PSR_C_BIT;
-
-	case 0x3: /* cc */
-		return (~cpsr) & PSR_C_BIT;
-
-	case 0x4: /* mi */
-		return cpsr & PSR_N_BIT;
-
-	case 0x5: /* pl */
-		return (~cpsr) & PSR_N_BIT;
-
-	case 0x6: /* vs */
-		return cpsr & PSR_V_BIT;
-
-	case 0x7: /* vc */
-		return (~cpsr) & PSR_V_BIT;
+	int ret = arm_check_condition(cc << 28, cpsr);
 
-	case 0x8: /* hi */
-		cpsr &= ~(cpsr >> 1); /* PSR_C_BIT &= ~PSR_Z_BIT */
-		return cpsr & PSR_C_BIT;
-
-	case 0x9: /* ls */
-		cpsr &= ~(cpsr >> 1); /* PSR_C_BIT &= ~PSR_Z_BIT */
-		return (~cpsr) & PSR_C_BIT;
-
-	case 0xa: /* ge */
-		cpsr ^= (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
-		return (~cpsr) & PSR_N_BIT;
-
-	case 0xb: /* lt */
-		cpsr ^= (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
-		return cpsr & PSR_N_BIT;
-
-	case 0xc: /* gt */
-		temp = cpsr ^ (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
-		temp |= (cpsr << 1);	   /* PSR_N_BIT |= PSR_Z_BIT */
-		return (~temp) & PSR_N_BIT;
-
-	case 0xd: /* le */
-		temp = cpsr ^ (cpsr << 3); /* PSR_N_BIT ^= PSR_V_BIT */
-		temp |= (cpsr << 1);	   /* PSR_N_BIT |= PSR_Z_BIT */
-		return temp & PSR_N_BIT;
-
-	case 0xe: /* al */
-	case 0xf: /* unconditional */
-		return true;
-	}
-	BUG();
-	return false;
+	return (ret != ARM_OPCODE_CONDTEST_FAIL);
 }
 
 static int is_last_scenario;
@@ -1128,7 +1074,9 @@ static unsigned long test_context_cpsr(int scenario)
 
 	if (!test_case_is_thumb) {
 		/* Testing ARM code */
-		probe_should_run = test_check_cc(current_instruction >> 28, cpsr) != 0;
+		int cc = current_instruction >> 28;
+
+		probe_should_run = test_check_cc(cc, cpsr) != 0;
 		if (scenario == 15)
 			is_last_scenario = true;
 

arch/arm/kernel/opcodes.c

@@ -0,0 +1,72 @@
+/*
+ *  linux/arch/arm/kernel/opcodes.c
+ *
+ *  A32 condition code lookup feature moved from nwfpe/fpopcode.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <asm/opcodes.h>
+
+#define ARM_OPCODE_CONDITION_UNCOND 0xf
+
+/*
+ * condition code lookup table
+ * index into the table is test code: EQ, NE, ... LT, GT, AL, NV
+ *
+ * bit position in short is condition code: NZCV
+ */
+static const unsigned short cc_map[16] = {
+	0xF0F0,			/* EQ == Z set            */
+	0x0F0F,			/* NE                     */
+	0xCCCC,			/* CS == C set            */
+	0x3333,			/* CC                     */
+	0xFF00,			/* MI == N set            */
+	0x00FF,			/* PL                     */
+	0xAAAA,			/* VS == V set            */
+	0x5555,			/* VC                     */
+	0x0C0C,			/* HI == C set && Z clear */
+	0xF3F3,			/* LS == C clear || Z set */
+	0xAA55,			/* GE == (N==V)           */
+	0x55AA,			/* LT == (N!=V)           */
+	0x0A05,			/* GT == (!Z && (N==V))   */
+	0xF5FA,			/* LE == (Z || (N!=V))    */
+	0xFFFF,			/* AL always              */
+	0			/* NV                     */
+};
+
+/*
+ * Returns:
+ * ARM_OPCODE_CONDTEST_FAIL   - if condition fails
+ * ARM_OPCODE_CONDTEST_PASS   - if condition passes (including AL)
+ * ARM_OPCODE_CONDTEST_UNCOND - if NV condition, or separate unconditional
+ *                              opcode space from v5 onwards
+ *
+ * Code that tests whether a conditional instruction would pass its condition
+ * check should check that return value == ARM_OPCODE_CONDTEST_PASS.
+ *
+ * Code that tests if a condition means that the instruction would be executed
+ * (regardless of conditional or unconditional) should instead check that the
+ * return value != ARM_OPCODE_CONDTEST_FAIL.
+ */
+asmlinkage unsigned int arm_check_condition(u32 opcode, u32 psr)
+{
+	u32 cc_bits  = opcode >> 28;
+	u32 psr_cond = psr >> 28;
+	unsigned int ret;
+
+	if (cc_bits != ARM_OPCODE_CONDITION_UNCOND) {
+		if ((cc_map[cc_bits] >> (psr_cond)) & 1)
+			ret = ARM_OPCODE_CONDTEST_PASS;
+		else
+			ret = ARM_OPCODE_CONDTEST_FAIL;
+	} else {
+		ret = ARM_OPCODE_CONDTEST_UNCOND;
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(arm_check_condition);

arch/arm/kernel/process.c

@@ -147,14 +147,8 @@ void soft_restart(unsigned long addr)
 	BUG();
 }
 
-void arm_machine_restart(char mode, const char *cmd)
+static void null_restart(char mode, const char *cmd)
 {
-	/* Disable interrupts first */
-	local_irq_disable();
-	local_fiq_disable();
-
-	/* Call the architecture specific reboot code. */
-	arch_reset(mode, cmd);
 }
 
 /*
@@ -163,7 +157,7 @@ void arm_machine_restart(char mode, const char *cmd)
 void (*pm_power_off)(void);
 EXPORT_SYMBOL(pm_power_off);
 
-void (*arm_pm_restart)(char str, const char *cmd) = arm_machine_restart;
+void (*arm_pm_restart)(char str, const char *cmd) = null_restart;
 EXPORT_SYMBOL_GPL(arm_pm_restart);
 
 static void do_nothing(void *unused)

arch/arm/kernel/sched_clock.c

@@ -14,61 +14,153 @@
 
 #include <asm/sched_clock.h>
 
+struct clock_data {
+	u64 epoch_ns;
+	u32 epoch_cyc;
+	u32 epoch_cyc_copy;
+	u32 mult;
+	u32 shift;
+};
+
 static void sched_clock_poll(unsigned long wrap_ticks);
 static DEFINE_TIMER(sched_clock_timer, sched_clock_poll, 0, 0);
-static void (*sched_clock_update_fn)(void);
+
+static struct clock_data cd = {
+	.mult	= NSEC_PER_SEC / HZ,
+};
+
+static u32 __read_mostly sched_clock_mask = 0xffffffff;
+
+static u32 notrace jiffy_sched_clock_read(void)
+{
+	return (u32)(jiffies - INITIAL_JIFFIES);
+}
+
+static u32 __read_mostly (*read_sched_clock)(void) = jiffy_sched_clock_read;
+
+static inline u64 cyc_to_ns(u64 cyc, u32 mult, u32 shift)
+{
+	return (cyc * mult) >> shift;
+}
+
+static unsigned long long cyc_to_sched_clock(u32 cyc, u32 mask)
+{
+	u64 epoch_ns;
+	u32 epoch_cyc;
+
+	/*
+	 * Load the epoch_cyc and epoch_ns atomically.  We do this by
+	 * ensuring that we always write epoch_cyc, epoch_ns and
+	 * epoch_cyc_copy in strict order, and read them in strict order.
+	 * If epoch_cyc and epoch_cyc_copy are not equal, then we're in
+	 * the middle of an update, and we should repeat the load.
+	 */
+	do {
+		epoch_cyc = cd.epoch_cyc;
+		smp_rmb();
+		epoch_ns = cd.epoch_ns;
+		smp_rmb();
+	} while (epoch_cyc != cd.epoch_cyc_copy);
+
+	return epoch_ns + cyc_to_ns((cyc - epoch_cyc) & mask, cd.mult, cd.shift);
+}
+
+/*
+ * Atomically update the sched_clock epoch.
+ */
+static void notrace update_sched_clock(void)
+{
+	unsigned long flags;
+	u32 cyc;
+	u64 ns;
+
+	cyc = read_sched_clock();
+	ns = cd.epoch_ns +
+		cyc_to_ns((cyc - cd.epoch_cyc) & sched_clock_mask,
+			  cd.mult, cd.shift);
+	/*
+	 * Write epoch_cyc and epoch_ns in a way that the update is
+	 * detectable in cyc_to_fixed_sched_clock().
+	 */
+	raw_local_irq_save(flags);
+	cd.epoch_cyc = cyc;
+	smp_wmb();
+	cd.epoch_ns = ns;
+	smp_wmb();
+	cd.epoch_cyc_copy = cyc;
+	raw_local_irq_restore(flags);
+}
 
 static void sched_clock_poll(unsigned long wrap_ticks)
 {
 	mod_timer(&sched_clock_timer, round_jiffies(jiffies + wrap_ticks));
-	sched_clock_update_fn();
+	update_sched_clock();
 }
 
-void __init init_sched_clock(struct clock_data *cd, void (*update)(void),
-	unsigned int clock_bits, unsigned long rate)
+void __init setup_sched_clock(u32 (*read)(void), int bits, unsigned long rate)
 {
 	unsigned long r, w;
 	u64 res, wrap;
 	char r_unit;
 
-	sched_clock_update_fn = update;
+	BUG_ON(bits > 32);
+	WARN_ON(!irqs_disabled());
+	WARN_ON(read_sched_clock != jiffy_sched_clock_read);
+	read_sched_clock = read;
+	sched_clock_mask = (1 << bits) - 1;
 
 	/* calculate the mult/shift to convert counter ticks to ns. */
-	clocks_calc_mult_shift(&cd->mult, &cd->shift, rate, NSEC_PER_SEC, 0);
+	clocks_calc_mult_shift(&cd.mult, &cd.shift, rate, NSEC_PER_SEC, 0);
 
 	r = rate;
 	if (r >= 4000000) {
 		r /= 1000000;
 		r_unit = 'M';
-	} else {
+	} else if (r >= 1000) {
 		r /= 1000;
 		r_unit = 'k';
-	}
+	} else
+		r_unit = ' ';
 
 	/* calculate how many ns until we wrap */
-	wrap = cyc_to_ns((1ULL << clock_bits) - 1, cd->mult, cd->shift);
+	wrap = cyc_to_ns((1ULL << bits) - 1, cd.mult, cd.shift);
 	do_div(wrap, NSEC_PER_MSEC);
 	w = wrap;
 
 	/* calculate the ns resolution of this counter */
-	res = cyc_to_ns(1ULL, cd->mult, cd->shift);
+	res = cyc_to_ns(1ULL, cd.mult, cd.shift);
 	pr_info("sched_clock: %u bits at %lu%cHz, resolution %lluns, wraps every %lums\n",
-		clock_bits, r, r_unit, res, w);
+		bits, r, r_unit, res, w);
 
 	/*
 	 * Start the timer to keep sched_clock() properly updated and
 	 * sets the initial epoch.
 	 */
 	sched_clock_timer.data = msecs_to_jiffies(w - (w / 10));
-	update();
+	update_sched_clock();
 
 	/*
 	 * Ensure that sched_clock() starts off at 0ns
 	 */
-	cd->epoch_ns = 0;
+	cd.epoch_ns = 0;
+
+	pr_debug("Registered %pF as sched_clock source\n", read);
+}
+
+unsigned long long notrace sched_clock(void)
+{
+	u32 cyc = read_sched_clock();
+	return cyc_to_sched_clock(cyc, sched_clock_mask);
 }
 
 void __init sched_clock_postinit(void)
 {
+	/*
+	 * If no sched_clock function has been provided at that point,
+	 * make it the final one one.
+	 */
+	if (read_sched_clock == jiffy_sched_clock_read)
+		setup_sched_clock(jiffy_sched_clock_read, 32, HZ);
+
 	sched_clock_poll(sched_clock_timer.data);
 }

arch/arm/kernel/smp_twd.c

@@ -10,8 +10,11 @@
  */
 #include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/cpufreq.h>
 #include <linux/delay.h>
 #include <linux/device.h>
+#include <linux/err.h>
 #include <linux/smp.h>
 #include <linux/jiffies.h>
 #include <linux/clockchips.h>
@@ -25,6 +28,7 @@
 /* set up by the platform code */
 void __iomem *twd_base;
 
+static struct clk *twd_clk;
 static unsigned long twd_timer_rate;
 
 static struct clock_event_device __percpu **twd_evt;
@@ -89,6 +93,52 @@ void twd_timer_stop(struct clock_event_device *clk)
 	disable_percpu_irq(clk->irq);
 }
 
+#ifdef CONFIG_CPU_FREQ
+
+/*
+ * Updates clockevent frequency when the cpu frequency changes.
+ * Called on the cpu that is changing frequency with interrupts disabled.
+ */
+static void twd_update_frequency(void *data)
+{
+	twd_timer_rate = clk_get_rate(twd_clk);
+
+	clockevents_update_freq(*__this_cpu_ptr(twd_evt), twd_timer_rate);
+}
+
+static int twd_cpufreq_transition(struct notifier_block *nb,
+	unsigned long state, void *data)
+{
+	struct cpufreq_freqs *freqs = data;
+
+	/*
+	 * The twd clock events must be reprogrammed to account for the new
+	 * frequency.  The timer is local to a cpu, so cross-call to the
+	 * changing cpu.
+	 */
+	if (state == CPUFREQ_POSTCHANGE || state == CPUFREQ_RESUMECHANGE)
+		smp_call_function_single(freqs->cpu, twd_update_frequency,
+			NULL, 1);
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block twd_cpufreq_nb = {
+	.notifier_call = twd_cpufreq_transition,
+};
+
+static int twd_cpufreq_init(void)
+{
+	if (!IS_ERR(twd_clk))
+		return cpufreq_register_notifier(&twd_cpufreq_nb,
+			CPUFREQ_TRANSITION_NOTIFIER);
+
+	return 0;
+}
+core_initcall(twd_cpufreq_init);
+
+#endif
+
 static void __cpuinit twd_calibrate_rate(void)
 {
 	unsigned long count;
@@ -140,6 +190,35 @@ static irqreturn_t twd_handler(int irq, void *dev_id)
 	return IRQ_NONE;
 }
 
+static struct clk *twd_get_clock(void)
+{
+	struct clk *clk;
+	int err;
+
+	clk = clk_get_sys("smp_twd", NULL);
+	if (IS_ERR(clk)) {
+		pr_err("smp_twd: clock not found: %d\n", (int)PTR_ERR(clk));
+		return clk;
+	}
+
+	err = clk_prepare(clk);
+	if (err) {
+		pr_err("smp_twd: clock failed to prepare: %d\n", err);
+		clk_put(clk);
+		return ERR_PTR(err);
+	}
+
+	err = clk_enable(clk);
+	if (err) {
+		pr_err("smp_twd: clock failed to enable: %d\n", err);
+		clk_unprepare(clk);
+		clk_put(clk);
+		return ERR_PTR(err);
+	}
+
+	return clk;
+}
+
 /*
  * Setup the local clock events for a CPU.
  */
@@ -165,7 +244,13 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 		}
 	}
 
-	twd_calibrate_rate();
+	if (!twd_clk)
+		twd_clk = twd_get_clock();
+
+	if (!IS_ERR_OR_NULL(twd_clk))
+		twd_timer_rate = clk_get_rate(twd_clk);
+	else
+		twd_calibrate_rate();
 
 	clk->name = "local_timer";
 	clk->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
@@ -173,15 +258,11 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 	clk->rating = 350;
 	clk->set_mode = twd_set_mode;
 	clk->set_next_event = twd_set_next_event;
-	clk->shift = 20;
-	clk->mult = div_sc(twd_timer_rate, NSEC_PER_SEC, clk->shift);
-	clk->max_delta_ns = clockevent_delta2ns(0xffffffff, clk);
-	clk->min_delta_ns = clockevent_delta2ns(0xf, clk);
 
 	this_cpu_clk = __this_cpu_ptr(twd_evt);
 	*this_cpu_clk = clk;
 
-	clockevents_register_device(clk);
-
+	clockevents_config_and_register(clk, twd_timer_rate,
+					0xf, 0xffffffff);
 	enable_percpu_irq(clk->irq, 0);
 }

arch/arm/kernel/swp_emulate.c

@@ -25,6 +25,7 @@
 #include <linux/syscalls.h>
 #include <linux/perf_event.h>
 
+#include <asm/opcodes.h>
 #include <asm/traps.h>
 #include <asm/uaccess.h>
 
@@ -185,6 +186,21 @@ static int swp_handler(struct pt_regs *regs, unsigned int instr)
 
 	perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, regs, regs->ARM_pc);
 
+	res = arm_check_condition(instr, regs->ARM_cpsr);
+	switch (res) {
+	case ARM_OPCODE_CONDTEST_PASS:
+		break;
+	case ARM_OPCODE_CONDTEST_FAIL:
+		/* Condition failed - return to next instruction */
+		regs->ARM_pc += 4;
+		return 0;
+	case ARM_OPCODE_CONDTEST_UNCOND:
+		/* If unconditional encoding - not a SWP, undef */
+		return -EFAULT;
+	default:
+		return -EINVAL;
+	}
+
 	if (current->pid != previous_pid) {
 		pr_debug("\"%s\" (%ld) uses deprecated SWP{B} instruction\n",
 			 current->comm, (unsigned long)current->pid);

arch/arm/kernel/tcm.c

@@ -180,9 +180,9 @@ static int __init setup_tcm_bank(u8 type, u8 bank, u8 banks,
  */
 void __init tcm_init(void)
 {
-	u32 tcm_status = read_cpuid_tcmstatus();
-	u8 dtcm_banks = (tcm_status >> 16) & 0x03;
-	u8 itcm_banks = (tcm_status & 0x03);
+	u32 tcm_status;
+	u8 dtcm_banks;
+	u8 itcm_banks;
 	size_t dtcm_code_sz = &__edtcm_data - &__sdtcm_data;
 	size_t itcm_code_sz = &__eitcm_text - &__sitcm_text;
 	char *start;
@@ -191,6 +191,22 @@ void __init tcm_init(void)
 	int ret;
 	int i;
 
+	/*
+	 * Prior to ARMv5 there is no TCM, and trying to read the status
+	 * register will hang the processor.
+	 */
+	if (cpu_architecture() < CPU_ARCH_ARMv5) {
+		if (dtcm_code_sz || itcm_code_sz)
+			pr_info("CPU TCM: %u bytes of DTCM and %u bytes of "
+				"ITCM code compiled in, but no TCM present "
+				"in pre-v5 CPU\n", dtcm_code_sz, itcm_code_sz);
+		return;
+	}
+
+	tcm_status = read_cpuid_tcmstatus();
+	dtcm_banks = (tcm_status >> 16) & 0x03;
+	itcm_banks = (tcm_status & 0x03);
+
 	/* Values greater than 2 for D/ITCM banks are "reserved" */
 	if (dtcm_banks > 2)
 		dtcm_banks = 0;

arch/arm/mach-at91/Kconfig

@@ -3,6 +3,12 @@ if ARCH_AT91
 config HAVE_AT91_DATAFLASH_CARD
 	bool
 
+config HAVE_AT91_DBGU0
+	bool
+
+config HAVE_AT91_DBGU1
+	bool
+
 config HAVE_AT91_USART3
 	bool
 
@@ -21,12 +27,14 @@ config ARCH_AT91RM9200
 	bool "AT91RM9200"
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 
 config ARCH_AT91SAM9260
 	bool "AT91SAM9260 or AT91SAM9XE"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
@@ -37,11 +45,13 @@ config ARCH_AT91SAM9261
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
+	select HAVE_AT91_DBGU0
 
 config ARCH_AT91SAM9G10
 	bool "AT91SAM9G10"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_FB_ATMEL
 
 config ARCH_AT91SAM9263
@@ -50,6 +60,7 @@ config ARCH_AT91SAM9263
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
@@ -57,11 +68,13 @@ config ARCH_AT91SAM9RL
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
+	select HAVE_AT91_DBGU0
 
 config ARCH_AT91SAM9G20
 	bool "AT91SAM9G20"
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
+	select HAVE_AT91_DBGU0
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
@@ -74,6 +87,7 @@ config ARCH_AT91SAM9G45
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
@@ -81,6 +95,7 @@ config ARCH_AT91CAP9
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
 	select HAVE_NET_MACB
+	select HAVE_AT91_DBGU1
 
 config ARCH_AT91X40
 	bool "AT91x40"
@@ -510,8 +525,13 @@ config AT91_TIMER_HZ
 choice
 	prompt "Select a UART for early kernel messages"
 
-config AT91_EARLY_DBGU
-	bool "DBGU"
+config AT91_EARLY_DBGU0
+	bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl"
+	depends on HAVE_AT91_DBGU0
+
+config AT91_EARLY_DBGU1
+	bool "DBGU on 9263, 9g45 and cap9"
+	depends on HAVE_AT91_DBGU1
 
 config AT91_EARLY_USART0
 	bool "USART0"

arch/arm/mach-at91/at91cap9.c

@@ -13,7 +13,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -23,11 +22,11 @@
 #include <mach/at91cap9.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -137,7 +136,7 @@ static struct clk pwm_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91CAP9_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -210,6 +209,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk),
 	CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
@@ -221,6 +222,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioABCD_clk),
+	CLKDEV_CON_ID("pioB", &pioABCD_clk),
+	CLKDEV_CON_ID("pioC", &pioABCD_clk),
+	CLKDEV_CON_ID("pioD", &pioABCD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -293,37 +298,27 @@ void __init at91cap9_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91cap9_gpio[] = {
+static struct at91_gpio_bank at91cap9_gpio[] __initdata = {
 	{
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOA,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOA,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOB,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOB,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOC,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOC,
 	}, {
 		.id		= AT91CAP9_ID_PIOABCD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioABCD_clk,
+		.regbase	= AT91CAP9_BASE_PIOD,
 	}
 };
 
-static void at91cap9_reset(void)
+static void at91cap9_restart(char mode, const char *cmd)
 {
 	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
-static void at91cap9_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91CAP9 processor initialization
  * -------------------------------------------------------------------- */
@@ -333,10 +328,16 @@ static void __init at91cap9_map_io(void)
 	at91_init_sram(0, AT91CAP9_SRAM_BASE, AT91CAP9_SRAM_SIZE);
 }
 
+static void __init at91cap9_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC);
+}
+
 static void __init at91cap9_initialize(void)
 {
-	at91_arch_reset = at91cap9_reset;
-	pm_power_off = at91cap9_poweroff;
+	arm_pm_restart = at91cap9_restart;
 	at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1);
 
 	/* Register GPIO subsystem */
@@ -394,6 +395,7 @@ static unsigned int at91cap9_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91cap9_soc = {
 	.map_io = at91cap9_map_io,
 	.default_irq_priority = at91cap9_default_irq_priority,
+	.ioremap_registers = at91cap9_ioremap_registers,
 	.register_clocks = at91cap9_register_clocks,
 	.init = at91cap9_initialize,
 };

arch/arm/mach-at91/at91cap9_devices.c

@@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -179,7 +179,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -200,7 +200,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -227,12 +227,12 @@ static struct platform_device at91cap9_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -264,7 +264,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91cap9_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -332,13 +332,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -398,8 +398,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91CAP9_BASE_ECC,
+		.end	= AT91CAP9_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -425,15 +425,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -670,8 +670,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91CAP9_BASE_RTT,
+		.end	= AT91CAP9_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -694,10 +694,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91CAP9_BASE_WDT,
+		.end	= AT91CAP9_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91cap9_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -807,7 +816,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PA9, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -1021,8 +1030,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91CAP9_BASE_DBGU,
+		.end	= AT91CAP9_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91rm9200.c

@@ -23,6 +23,7 @@
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 static struct map_desc at91rm9200_io_desc[] __initdata = {
 	{
@@ -195,6 +196,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -268,27 +273,23 @@ void __init at91rm9200_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91rm9200_gpio[] = {
+static struct at91_gpio_bank at91rm9200_gpio[] __initdata = {
 	{
 		.id		= AT91RM9200_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91RM9200_BASE_PIOA,
 	}, {
 		.id		= AT91RM9200_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91RM9200_BASE_PIOB,
 	}, {
 		.id		= AT91RM9200_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91RM9200_BASE_PIOC,
 	}, {
 		.id		= AT91RM9200_ID_PIOD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioD_clk,
+		.regbase	= AT91RM9200_BASE_PIOD,
 	}
 };
 
-static void at91rm9200_reset(void)
+static void at91rm9200_restart(char mode, const char *cmd)
 {
 	/*
 	 * Perform a hardware reset with the use of the Watchdog timer.
@@ -307,9 +308,13 @@ static void __init at91rm9200_map_io(void)
 	iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc));
 }
 
+static void __init at91rm9200_ioremap_registers(void)
+{
+}
+
 static void __init at91rm9200_initialize(void)
 {
-	at91_arch_reset = at91rm9200_reset;
+	arm_pm_restart = at91rm9200_restart;
 	at91_extern_irq = (1 << AT91RM9200_ID_IRQ0) | (1 << AT91RM9200_ID_IRQ1)
 			| (1 << AT91RM9200_ID_IRQ2) | (1 << AT91RM9200_ID_IRQ3)
 			| (1 << AT91RM9200_ID_IRQ4) | (1 << AT91RM9200_ID_IRQ5)
@@ -366,6 +371,7 @@ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91rm9200_soc = {
 	.map_io = at91rm9200_map_io,
 	.default_irq_priority = at91rm9200_default_irq_priority,
+	.ioremap_registers = at91rm9200_ioremap_registers,
 	.register_clocks = at91rm9200_register_clocks,
 	.init = at91rm9200_initialize,
 };

arch/arm/mach-at91/at91rm9200_devices.c

@@ -114,11 +114,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
-	if (data->pullup_pin)
+	if (gpio_is_valid(data->pullup_pin))
 		at91_set_gpio_output(data->pullup_pin, 0);
 
 	udc_data = *data;
@@ -135,7 +135,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -162,12 +162,12 @@ static struct platform_device at91rm9200_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -199,7 +199,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91rm9200_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	);
 
 	/* input/irq */
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
@@ -268,7 +268,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	at91_set_deglitch(data->det_pin, 1);
 
 	/* outputs, initially off */
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 	at91_set_gpio_output(data->rst_pin, 0);
 
@@ -328,13 +328,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC1, 0);		/* SMOE */
@@ -665,10 +665,24 @@ static void __init at91_add_device_tc(void) { }
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+	[0] = {
+		.start	= AT91RM9200_BASE_RTC,
+		.end	= AT91RM9200_BASE_RTC + SZ_256 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device at91rm9200_rtc_device = {
 	.name		= "at91_rtc",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= rtc_resources,
+	.num_resources	= ARRAY_SIZE(rtc_resources),
 };
 
 static void __init at91_add_device_rtc(void)
@@ -877,8 +891,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91RM9200_BASE_DBGU,
+		.end	= AT91RM9200_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91rm9200_time.c

@@ -32,6 +32,8 @@ static unsigned long last_crtr;
 static u32 irqmask;
 static struct clock_event_device clkevt;
 
+#define RM9200_TIMER_LATCH	((AT91_SLOW_CLOCK + HZ/2) / HZ)
+
 /*
  * The ST_CRTR is updated asynchronously to the master clock ... but
  * the updates as seen by the CPU don't seem to be strictly monotonic.
@@ -74,8 +76,8 @@ static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id)
 	if (sr & AT91_ST_PITS) {
 		u32	crtr = read_CRTR();
 
-		while (((crtr - last_crtr) & AT91_ST_CRTV) >= LATCH) {
-			last_crtr += LATCH;
+		while (((crtr - last_crtr) & AT91_ST_CRTV) >= RM9200_TIMER_LATCH) {
+			last_crtr += RM9200_TIMER_LATCH;
 			clkevt.event_handler(&clkevt);
 		}
 		return IRQ_HANDLED;
@@ -116,7 +118,7 @@ clkevt32k_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	case CLOCK_EVT_MODE_PERIODIC:
 		/* PIT for periodic irqs; fixed rate of 1/HZ */
 		irqmask = AT91_ST_PITS;
-		at91_sys_write(AT91_ST_PIMR, LATCH);
+		at91_sys_write(AT91_ST_PIMR, RM9200_TIMER_LATCH);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
 		/* ALM for oneshot irqs, set by next_event()

arch/arm/mach-at91/at91sam9260.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -21,11 +20,11 @@
 #include <mach/at91sam9260.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -120,7 +119,7 @@ static struct clk ohci_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9260_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -190,6 +189,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
@@ -209,6 +210,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -270,28 +274,19 @@ void __init at91sam9260_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9260_gpio[] = {
+static struct at91_gpio_bank at91sam9260_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9260_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9260_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9260_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9260_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9260_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9260_BASE_PIOC,
 	}
 };
 
-static void at91sam9260_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9260 processor initialization
  * -------------------------------------------------------------------- */
@@ -325,10 +320,16 @@ static void __init at91sam9260_map_io(void)
 	}
 }
 
+static void __init at91sam9260_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC);
+}
+
 static void __init at91sam9260_initialize(void)
 {
-	at91_arch_reset = at91sam9_alt_reset;
-	pm_power_off = at91sam9260_poweroff;
+	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1)
 			| (1 << AT91SAM9260_ID_IRQ2);
 
@@ -381,6 +382,7 @@ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9260_soc = {
 	.map_io = at91sam9260_map_io,
 	.default_irq_priority = at91sam9260_default_irq_priority,
+	.ioremap_registers = at91sam9260_ioremap_registers,
 	.register_clocks = at91sam9260_register_clocks,
 	.init = at91sam9260_initialize,
 };

arch/arm/mach-at91/at91sam9260_devices.c

@@ -115,7 +115,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -136,7 +136,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -163,12 +163,12 @@ static struct platform_device at91sam9260_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -200,7 +200,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9260_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -243,13 +243,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -330,11 +330,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
 		if (data->slot[i].bus_width) {
 			/* input/irq */
-			if (data->slot[i].detect_pin) {
+			if (gpio_is_valid(data->slot[i].detect_pin)) {
 				at91_set_gpio_input(data->slot[i].detect_pin, 1);
 				at91_set_deglitch(data->slot[i].detect_pin, 1);
 			}
-			if (data->slot[i].wp_pin)
+			if (gpio_is_valid(data->slot[i].wp_pin))
 				at91_set_gpio_input(data->slot[i].wp_pin, 1);
 
 			switch (i) {
@@ -399,8 +399,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9260_BASE_ECC,
+		.end	= AT91SAM9260_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -426,15 +426,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -714,8 +714,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9260_BASE_RTT,
+		.end	= AT91SAM9260_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -738,10 +738,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9260_BASE_WDT,
+		.end	= AT91SAM9260_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9260_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -837,8 +846,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9260_BASE_DBGU,
+		.end	= AT91SAM9260_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -1281,17 +1290,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 
 	at91_sys_write(AT91_MATRIX_EBICSA, csa);
 
-	if (data->rst_pin) {
+	if (gpio_is_valid(data->rst_pin)) {
 		at91_set_multi_drive(data->rst_pin, 0);
 		at91_set_gpio_output(data->rst_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 0);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 0);
 		at91_set_deglitch(data->det_pin, 1);
 	}

arch/arm/mach-at91/at91sam9261.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -20,11 +19,11 @@
 #include <mach/at91sam9261.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -176,6 +175,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -251,28 +253,19 @@ void __init at91sam9261_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9261_gpio[] = {
+static struct at91_gpio_bank at91sam9261_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9261_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9261_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9261_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9261_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9261_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9261_BASE_PIOC,
 	}
 };
 
-static void at91sam9261_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9261 processor initialization
  * -------------------------------------------------------------------- */
@@ -285,10 +278,16 @@ static void __init at91sam9261_map_io(void)
 		at91_init_sram(0, AT91SAM9261_SRAM_BASE, AT91SAM9261_SRAM_SIZE);
 }
 
+static void __init at91sam9261_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC);
+}
+
 static void __init at91sam9261_initialize(void)
 {
-	at91_arch_reset = at91sam9_alt_reset;
-	pm_power_off = at91sam9261_poweroff;
+	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1)
 			| (1 << AT91SAM9261_ID_IRQ2);
 
@@ -341,6 +340,7 @@ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9261_soc = {
 	.map_io = at91sam9261_map_io,
 	.default_irq_priority = at91sam9261_default_irq_priority,
+	.ioremap_registers = at91sam9261_ioremap_registers,
 	.register_clocks = at91sam9261_register_clocks,
 	.init = at91sam9261_initialize,
 };

arch/arm/mach-at91/at91sam9261_devices.c

@@ -118,7 +118,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -171,13 +171,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -240,15 +240,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PC0, 0);		/* NANDOE */
@@ -600,8 +600,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9261_BASE_RTT,
+		.end	= AT91SAM9261_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -624,10 +624,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9261_BASE_WDT,
+		.end	= AT91SAM9261_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9261_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -816,8 +825,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9261_BASE_DBGU,
+		.end	= AT91SAM9261_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam9263.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -19,11 +18,11 @@
 #include <mach/at91sam9263.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -118,7 +117,7 @@ static struct clk pwm_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9263_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -182,6 +181,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
 	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
@@ -191,6 +192,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioCDE_clk),
+	CLKDEV_CON_ID("pioD", &pioCDE_clk),
+	CLKDEV_CON_ID("pioE", &pioCDE_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -263,36 +269,25 @@ void __init at91sam9263_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9263_gpio[] = {
+static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9263_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9263_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9263_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9263_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOC,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOD,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOD,
 	}, {
 		.id		= AT91SAM9263_ID_PIOCDE,
-		.offset		= AT91_PIOE,
-		.clock		= &pioCDE_clk,
+		.regbase	= AT91SAM9263_BASE_PIOE,
 	}
 };
 
-static void at91sam9263_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9263 processor initialization
  * -------------------------------------------------------------------- */
@@ -303,10 +298,17 @@ static void __init at91sam9263_map_io(void)
 	at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
 }
 
+static void __init at91sam9263_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
+	at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
+}
+
 static void __init at91sam9263_initialize(void)
 {
-	at91_arch_reset = at91sam9_alt_reset;
-	pm_power_off = at91sam9263_poweroff;
+	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1);
 
 	/* Register GPIO subsystem */
@@ -358,6 +360,7 @@ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9263_soc = {
 	.map_io = at91sam9263_map_io,
 	.default_irq_priority = at91sam9263_default_irq_priority,
+	.ioremap_registers = at91sam9263_ioremap_registers,
 	.register_clocks = at91sam9263_register_clocks,
 	.init = at91sam9263_initialize,
 };

arch/arm/mach-at91/at91sam9263_devices.c

@@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -123,7 +123,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data)
 	if (!data)
 		return;
 
-	if (data->vbus_pin) {
+	if (gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 	}
@@ -144,7 +144,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -171,12 +171,12 @@ static struct platform_device at91sam9263_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -208,7 +208,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9263_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -276,13 +276,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -430,17 +430,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data)
 	}
 	at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
 
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
 
-	if (data->irq_pin) {
+	if (gpio_is_valid(data->irq_pin)) {
 		at91_set_gpio_input(data->irq_pin, 1);
 		at91_set_deglitch(data->irq_pin, 1);
 	}
 
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		/* initially off */
 		at91_set_gpio_output(data->vcc_pin, 0);
 
@@ -473,8 +473,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC0,
-		.end	= AT91_BASE_SYS + AT91_ECC0 + SZ_512 - 1,
+		.start	= AT91SAM9263_BASE_ECC0,
+		.end	= AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -500,15 +500,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -749,7 +749,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PB3, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -956,8 +956,8 @@ static void __init at91_add_device_tc(void) { }
 
 static struct resource rtt0_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT0,
-		.end	= AT91_BASE_SYS + AT91_RTT0 + SZ_16 - 1,
+		.start	= AT91SAM9263_BASE_RTT0,
+		.end	= AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -971,8 +971,8 @@ static struct platform_device at91sam9263_rtt0_device = {
 
 static struct resource rtt1_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT1,
-		.end	= AT91_BASE_SYS + AT91_RTT1 + SZ_16 - 1,
+		.start	= AT91SAM9263_BASE_RTT1,
+		.end	= AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -996,10 +996,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9263_BASE_WDT,
+		.end	= AT91SAM9263_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9263_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -1196,8 +1205,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9263_BASE_DBGU,
+		.end	= AT91SAM9263_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam926x_time.c

@@ -25,7 +25,17 @@
 
 static u32 pit_cycle;		/* write-once */
 static u32 pit_cnt;		/* access only w/system irq blocked */
+static void __iomem *pit_base_addr __read_mostly;
 
+static inline unsigned int pit_read(unsigned int reg_offset)
+{
+	return __raw_readl(pit_base_addr + reg_offset);
+}
+
+static inline void pit_write(unsigned int reg_offset, unsigned long value)
+{
+	__raw_writel(value, pit_base_addr + reg_offset);
+}
 
 /*
  * Clocksource:  just a monotonic counter of MCK/16 cycles.
@@ -39,7 +49,7 @@ static cycle_t read_pit_clk(struct clocksource *cs)
 
 	raw_local_irq_save(flags);
 	elapsed = pit_cnt;
-	t = at91_sys_read(AT91_PIT_PIIR);
+	t = pit_read(AT91_PIT_PIIR);
 	raw_local_irq_restore(flags);
 
 	elapsed += PIT_PICNT(t) * pit_cycle;
@@ -64,8 +74,8 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	switch (mode) {
 	case CLOCK_EVT_MODE_PERIODIC:
 		/* update clocksource counter */
-		pit_cnt += pit_cycle * PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
-		at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
+		pit_cnt += pit_cycle * PIT_PICNT(pit_read(AT91_PIT_PIVR));
+		pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN
 				| AT91_PIT_PITIEN);
 		break;
 	case CLOCK_EVT_MODE_ONESHOT:
@@ -74,7 +84,7 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev)
 	case CLOCK_EVT_MODE_SHUTDOWN:
 	case CLOCK_EVT_MODE_UNUSED:
 		/* disable irq, leaving the clocksource active */
-		at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+		pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
 		break;
 	case CLOCK_EVT_MODE_RESUME:
 		break;
@@ -103,11 +113,11 @@ static irqreturn_t at91sam926x_pit_interrupt(int irq, void *dev_id)
 
 	/* The PIT interrupt may be disabled, and is shared */
 	if ((pit_clkevt.mode == CLOCK_EVT_MODE_PERIODIC)
-			&& (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
+			&& (pit_read(AT91_PIT_SR) & AT91_PIT_PITS)) {
 		unsigned nr_ticks;
 
 		/* Get number of ticks performed before irq, and ack it */
-		nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR));
+		nr_ticks = PIT_PICNT(pit_read(AT91_PIT_PIVR));
 		do {
 			pit_cnt += pit_cycle;
 			pit_clkevt.event_handler(&pit_clkevt);
@@ -129,14 +139,14 @@ static struct irqaction at91sam926x_pit_irq = {
 static void at91sam926x_pit_reset(void)
 {
 	/* Disable timer and irqs */
-	at91_sys_write(AT91_PIT_MR, 0);
+	pit_write(AT91_PIT_MR, 0);
 
 	/* Clear any pending interrupts, wait for PIT to stop counting */
-	while (PIT_CPIV(at91_sys_read(AT91_PIT_PIVR)) != 0)
+	while (PIT_CPIV(pit_read(AT91_PIT_PIVR)) != 0)
 		cpu_relax();
 
 	/* Start PIT but don't enable IRQ */
-	at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
+	pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN);
 }
 
 /*
@@ -178,7 +188,15 @@ static void __init at91sam926x_pit_init(void)
 static void at91sam926x_pit_suspend(void)
 {
 	/* Disable timer */
-	at91_sys_write(AT91_PIT_MR, 0);
+	pit_write(AT91_PIT_MR, 0);
+}
+
+void __init at91sam926x_ioremap_pit(u32 addr)
+{
+	pit_base_addr = ioremap(addr, 16);
+
+	if (!pit_base_addr)
+		panic("Impossible to ioremap PIT\n");
 }
 
 struct sys_timer at91sam926x_timer = {

arch/arm/mach-at91/at91sam9_alt_reset.S

@@ -14,20 +14,15 @@
  */
 
 #include <linux/linkage.h>
-#include <asm/system.h>
 #include <mach/hardware.h>
 #include <mach/at91sam9_sdramc.h>
 #include <mach/at91_rstc.h>
 
 			.arm
 
-			.globl	at91sam9_alt_reset
+			.globl	at91sam9_alt_restart
 
-at91sam9_alt_reset:	mrc	p15, 0, r0, c1, c0, 0
-			orr	r0, r0, #CR_I
-			mcr	p15, 0, r0, c1, c0, 0		@ enable I-cache
-
-			ldr	r0, .at91_va_base_sdramc	@ preload constants
+at91sam9_alt_restart:	ldr	r0, .at91_va_base_sdramc	@ preload constants
 			ldr	r1, .at91_va_base_rstc_cr
 
 			mov	r2, #1

arch/arm/mach-at91/at91sam9g45.c

@@ -11,7 +11,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 #include <linux/dma-mapping.h>
 
 #include <asm/irq.h>
@@ -20,12 +19,12 @@
 #include <mach/at91sam9g45.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 #include <mach/cpu.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -150,7 +149,7 @@ static struct clk ac97_clk = {
 	.type		= CLK_TYPE_PERIPHERAL,
 };
 static struct clk macb_clk = {
-	.name		= "macb_clk",
+	.name		= "pclk",
 	.pmc_mask	= 1 << AT91SAM9G45_ID_EMAC,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
@@ -209,6 +208,8 @@ static struct clk *periph_clocks[] __initdata = {
 };
 
 static struct clk_lookup periph_clocks_lookups[] = {
+	/* One additional fake clock for macb_hclk */
+	CLKDEV_CON_ID("hclk", &macb_clk),
 	/* One additional fake clock for ohci */
 	CLKDEV_CON_ID("ohci_clk", &uhphs_clk),
 	CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk),
@@ -231,6 +232,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("usart", "fff98000.serial", &usart3_clk),
 	/* fake hclk clock */
 	CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioDE_clk),
+	CLKDEV_CON_ID("pioE", &pioDE_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -293,41 +299,30 @@ void __init at91sam9g45_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9g45_gpio[] = {
+static struct at91_gpio_bank at91sam9g45_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9G45_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9G45_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOD,
-		.clock		= &pioDE_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOD,
 	}, {
 		.id		= AT91SAM9G45_ID_PIODE,
-		.offset		= AT91_PIOE,
-		.clock		= &pioDE_clk,
+		.regbase	= AT91SAM9G45_BASE_PIOE,
 	}
 };
 
-static void at91sam9g45_reset(void)
+static void at91sam9g45_restart(char mode, const char *cmd)
 {
 	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
 }
 
-static void at91sam9g45_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9G45 processor initialization
  * -------------------------------------------------------------------- */
@@ -338,10 +333,16 @@ static void __init at91sam9g45_map_io(void)
 	init_consistent_dma_size(SZ_4M);
 }
 
+static void __init at91sam9g45_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC);
+}
+
 static void __init at91sam9g45_initialize(void)
 {
-	at91_arch_reset = at91sam9g45_reset;
-	pm_power_off = at91sam9g45_poweroff;
+	arm_pm_restart = at91sam9g45_restart;
 	at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0);
 
 	/* Register GPIO subsystem */
@@ -393,6 +394,7 @@ static unsigned int at91sam9g45_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9g45_soc = {
 	.map_io = at91sam9g45_map_io,
 	.default_irq_priority = at91sam9g45_default_irq_priority,
+	.ioremap_registers = at91sam9g45_ioremap_registers,
 	.register_clocks = at91sam9g45_register_clocks,
 	.init = at91sam9g45_initialize,
 };

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -44,8 +44,8 @@ static struct at_dma_platform_data atdma_pdata = {
 
 static struct resource hdmac_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DMA,
-		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_DMA,
+		.end	= AT91SAM9G45_BASE_DMA + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -181,7 +181,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
-		if (data->vbus_pin[i])
+		if (gpio_is_valid(data->vbus_pin[i]))
 			at91_set_gpio_output(data->vbus_pin[i], 0);
 	}
 
@@ -263,7 +263,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -284,7 +284,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {}
 
 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct at91_eth_data eth_data;
+static struct macb_platform_data eth_data;
 
 static struct resource eth_resources[] = {
 	[0] = {
@@ -311,12 +311,12 @@ static struct platform_device at91sam9g45_eth_device = {
 	.num_resources	= ARRAY_SIZE(eth_resources),
 };
 
-void __init at91_add_device_eth(struct at91_eth_data *data)
+void __init at91_add_device_eth(struct macb_platform_data *data)
 {
 	if (!data)
 		return;
 
-	if (data->phy_irq_pin) {
+	if (gpio_is_valid(data->phy_irq_pin)) {
 		at91_set_gpio_input(data->phy_irq_pin, 0);
 		at91_set_deglitch(data->phy_irq_pin, 1);
 	}
@@ -348,7 +348,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data)
 	platform_device_register(&at91sam9g45_eth_device);
 }
 #else
-void __init at91_add_device_eth(struct at91_eth_data *data) {}
+void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
@@ -449,11 +449,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 
 
 	/* input/irq */
-	if (data->slot[0].detect_pin) {
+	if (gpio_is_valid(data->slot[0].detect_pin)) {
 		at91_set_gpio_input(data->slot[0].detect_pin, 1);
 		at91_set_deglitch(data->slot[0].detect_pin, 1);
 	}
-	if (data->slot[0].wp_pin)
+	if (gpio_is_valid(data->slot[0].wp_pin))
 		at91_set_gpio_input(data->slot[0].wp_pin, 1);
 
 	if (mmc_id == 0) {		/* MCI0 */
@@ -529,8 +529,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_ECC,
+		.end	= AT91SAM9G45_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -556,15 +556,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	nand_data = *data;
@@ -859,7 +859,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD6, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -1009,10 +1009,24 @@ static void __init at91_add_device_tc(void) { }
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
+static struct resource rtc_resources[] = {
+	[0] = {
+		.start	= AT91SAM9G45_BASE_RTC,
+		.end	= AT91SAM9G45_BASE_RTC + SZ_256 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91_ID_SYS,
+		.end	= AT91_ID_SYS,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device at91sam9g45_rtc_device = {
 	.name		= "at91_rtc",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= rtc_resources,
+	.num_resources	= ARRAY_SIZE(rtc_resources),
 };
 
 static void __init at91_add_device_rtc(void)
@@ -1081,8 +1095,8 @@ void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {}
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9G45_BASE_RTT,
+		.end	= AT91SAM9G45_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -1133,10 +1147,19 @@ static void __init at91_add_device_trng(void) {}
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9G45_BASE_WDT,
+		.end	= AT91SAM9G45_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9g45_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -1332,8 +1355,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9G45_BASE_DBGU,
+		.end	= AT91SAM9G45_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/at91sam9rl.c

@@ -10,7 +10,6 @@
  */
 
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/irq.h>
 #include <asm/mach/arch.h>
@@ -20,11 +19,11 @@
 #include <mach/at91sam9rl.h>
 #include <mach/at91_pmc.h>
 #include <mach/at91_rstc.h>
-#include <mach/at91_shdwc.h>
 
 #include "soc.h"
 #include "generic.h"
 #include "clock.h"
+#include "sam9_smc.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -184,6 +183,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
+	CLKDEV_CON_ID("pioA", &pioA_clk),
+	CLKDEV_CON_ID("pioB", &pioB_clk),
+	CLKDEV_CON_ID("pioC", &pioC_clk),
+	CLKDEV_CON_ID("pioD", &pioD_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {
@@ -243,32 +246,22 @@ void __init at91sam9rl_set_console_clock(int id)
  *  GPIO
  * -------------------------------------------------------------------- */
 
-static struct at91_gpio_bank at91sam9rl_gpio[] = {
+static struct at91_gpio_bank at91sam9rl_gpio[] __initdata = {
 	{
 		.id		= AT91SAM9RL_ID_PIOA,
-		.offset		= AT91_PIOA,
-		.clock		= &pioA_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOA,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOB,
-		.offset		= AT91_PIOB,
-		.clock		= &pioB_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOB,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOC,
-		.offset		= AT91_PIOC,
-		.clock		= &pioC_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOC,
 	}, {
 		.id		= AT91SAM9RL_ID_PIOD,
-		.offset		= AT91_PIOD,
-		.clock		= &pioD_clk,
+		.regbase	= AT91SAM9RL_BASE_PIOD,
 	}
 };
 
-static void at91sam9rl_poweroff(void)
-{
-	at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW);
-}
-
-
 /* --------------------------------------------------------------------
  *  AT91SAM9RL processor initialization
  * -------------------------------------------------------------------- */
@@ -290,10 +283,16 @@ static void __init at91sam9rl_map_io(void)
 	at91_init_sram(0, AT91SAM9RL_SRAM_BASE, sram_size);
 }
 
+static void __init at91sam9rl_ioremap_registers(void)
+{
+	at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC);
+	at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT);
+	at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC);
+}
+
 static void __init at91sam9rl_initialize(void)
 {
-	at91_arch_reset = at91sam9_alt_reset;
-	pm_power_off = at91sam9rl_poweroff;
+	arm_pm_restart = at91sam9_alt_restart;
 	at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0);
 
 	/* Register GPIO subsystem */
@@ -345,6 +344,7 @@ static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = {
 struct at91_init_soc __initdata at91sam9rl_soc = {
 	.map_io = at91sam9rl_map_io,
 	.default_irq_priority = at91sam9rl_default_irq_priority,
+	.ioremap_registers = at91sam9rl_ioremap_registers,
 	.register_clocks = at91sam9rl_register_clocks,
 	.init = at91sam9rl_initialize,
 };

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -39,8 +39,8 @@ static struct at_dma_platform_data atdma_pdata = {
 
 static struct resource hdmac_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DMA,
-		.end	= AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_DMA,
+		.end	= AT91SAM9RL_BASE_DMA + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[2] = {
@@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data)
 	usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 	memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));
 
-	if (data && data->vbus_pin > 0) {
+	if (data && gpio_is_valid(data->vbus_pin)) {
 		at91_set_gpio_input(data->vbus_pin, 0);
 		at91_set_deglitch(data->vbus_pin, 1);
 		usba_udc_data.pdata.vbus_pin = data->vbus_pin;
@@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 		return;
 
 	/* input/irq */
-	if (data->det_pin) {
+	if (gpio_is_valid(data->det_pin)) {
 		at91_set_gpio_input(data->det_pin, 1);
 		at91_set_deglitch(data->det_pin, 1);
 	}
-	if (data->wp_pin)
+	if (gpio_is_valid(data->wp_pin))
 		at91_set_gpio_input(data->wp_pin, 1);
-	if (data->vcc_pin)
+	if (gpio_is_valid(data->vcc_pin))
 		at91_set_gpio_output(data->vcc_pin, 0);
 
 	/* CLK */
@@ -248,8 +248,8 @@ static struct resource nand_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91_BASE_SYS + AT91_ECC,
-		.end	= AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_ECC,
+		.end	= AT91SAM9RL_BASE_ECC + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
 
 	/* enable pin */
-	if (data->enable_pin)
+	if (gpio_is_valid(data->enable_pin))
 		at91_set_gpio_output(data->enable_pin, 1);
 
 	/* ready/busy pin */
-	if (data->rdy_pin)
+	if (gpio_is_valid(data->rdy_pin))
 		at91_set_gpio_input(data->rdy_pin, 1);
 
 	/* card detect pin */
-	if (data->det_pin)
+	if (gpio_is_valid(data->det_pin))
 		at91_set_gpio_input(data->det_pin, 1);
 
 	at91_set_A_periph(AT91_PIN_PB4, 0);		/* NANDOE */
@@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 	at91_set_A_periph(AT91_PIN_PD4, 0);	/* AC97RX */
 
 	/* reset */
-	if (data->reset_pin)
+	if (gpio_is_valid(data->reset_pin))
 		at91_set_gpio_output(data->reset_pin, 0);
 
 	ac97_data = *data;
@@ -685,8 +685,8 @@ static void __init at91_add_device_rtc(void) {}
 
 static struct resource rtt_resources[] = {
 	{
-		.start	= AT91_BASE_SYS + AT91_RTT,
-		.end	= AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
+		.start	= AT91SAM9RL_BASE_RTT,
+		.end	= AT91SAM9RL_BASE_RTT + SZ_16 - 1,
 		.flags	= IORESOURCE_MEM,
 	}
 };
@@ -709,10 +709,19 @@ static void __init at91_add_device_rtt(void)
  * -------------------------------------------------------------------- */
 
 #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
+static struct resource wdt_resources[] = {
+	{
+		.start	= AT91SAM9RL_BASE_WDT,
+		.end	= AT91SAM9RL_BASE_WDT + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
 static struct platform_device at91sam9rl_wdt_device = {
 	.name		= "at91_wdt",
 	.id		= -1,
-	.num_resources	= 0,
+	.resource	= wdt_resources,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
 };
 
 static void __init at91_add_device_watchdog(void)
@@ -908,8 +917,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
 #if defined(CONFIG_SERIAL_ATMEL)
 static struct resource dbgu_resources[] = {
 	[0] = {
-		.start	= AT91_BASE_SYS + AT91_DBGU,
-		.end	= AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1,
+		.start	= AT91SAM9RL_BASE_DBGU,
+		.end	= AT91SAM9RL_BASE_DBGU + SZ_512 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {

arch/arm/mach-at91/board-1arm.c

@@ -63,13 +63,15 @@ static void __init onearm_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata onearm_eth_data = {
+static struct macb_platform_data __initdata onearm_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata onearm_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata onearm_udc_data = {

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -75,6 +75,8 @@ static void __init afeb9260_init_early(void)
  */
 static struct at91_usbh_data __initdata afeb9260_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
  */
 static struct at91_udc_data __initdata afeb9260_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -103,7 +105,7 @@ static struct spi_board_info afeb9260_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata afeb9260_macb_data = {
+static struct macb_platform_data __initdata afeb9260_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA9,
 	.is_rmii	= 0,
 };
@@ -138,6 +140,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 	.bus_width_16	= 0,
 	.parts		= afeb9260_nand_partition,
 	.num_parts	= ARRAY_SIZE(afeb9260_nand_partition),
+	.det_pin	= -EINVAL,
 };
 
 
@@ -149,6 +152,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 	.wp_pin 	= AT91_PIN_PC4,
 	.slot_b		= 1,
 	.wire4		= 1,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -169,6 +173,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 static struct at91_cf_data afeb9260_cf_data = {
 	.chipselect = 4,
 	.irq_pin    = AT91_PIN_PA6,
+	.det_pin	= -EINVAL,
+	.vcc_pin	= -EINVAL,
 	.rst_pin    = AT91_PIN_PA7,
 	.flags      = AT91_CF_TRUE_IDE,
 };

arch/arm/mach-at91/board-cam60.c

@@ -62,6 +62,8 @@ static void __init cam60_init_early(void)
  */
 static struct at91_usbh_data __initdata cam60_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -115,7 +117,7 @@ static struct spi_board_info cam60_spi_devices[] __initdata = {
 /*
  * MACB Ethernet device
  */
-static struct __initdata at91_eth_data cam60_macb_data = {
+static struct __initdata macb_platform_data cam60_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PB5,
 	.is_rmii	= 0,
 };
@@ -135,7 +137,7 @@ static struct mtd_partition __initdata cam60_nand_partition[] = {
 static struct atmel_nand_data __initdata cam60_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA9,
 	.enable_pin	= AT91_PIN_PA7,
 	.parts		= cam60_nand_partition,
@@ -163,7 +165,7 @@ static struct sam9_smc_config __initdata cam60_nand_smc_config = {
 static void __init cam60_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &cam60_nand_smc_config);
+	sam9_smc_configure(0, 3, &cam60_nand_smc_config);
 
 	at91_add_device_nand(&cam60_nand_data);
 }

arch/arm/mach-at91/board-cap9adk.c

@@ -70,6 +70,8 @@ static void __init cap9adk_init_early(void)
  */
 static struct at91_usbh_data __initdata cap9adk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -144,16 +146,17 @@ static struct spi_board_info cap9adk_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata cap9adk_mmc_data = {
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata cap9adk_macb_data = {
+static struct macb_platform_data __initdata cap9adk_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -172,8 +175,8 @@ static struct mtd_partition __initdata cap9adk_nand_partitions[] = {
 static struct atmel_nand_data __initdata cap9adk_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
-//	.rdy_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.rdy_pin	= -EINVAL,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= cap9adk_nand_partitions,
 	.num_parts	= ARRAY_SIZE(cap9adk_nand_partitions),
@@ -212,7 +215,7 @@ static void __init cap9adk_add_device_nand(void)
 		cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &cap9adk_nand_smc_config);
+	sam9_smc_configure(0, 3, &cap9adk_nand_smc_config);
 
 	at91_add_device_nand(&cap9adk_nand_data);
 }
@@ -282,7 +285,7 @@ static __init void cap9adk_add_device_nor(void)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V);
 
 	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, &cap9adk_nor_smc_config);
+	sam9_smc_configure(0, 0, &cap9adk_nor_smc_config);
 
 	platform_device_register(&cap9adk_nor_flash);
 }
@@ -351,7 +354,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
  * AC97
  */
 static struct ac97c_platform_data cap9adk_ac97_data = {
-//	.reset_pin	= ... not connected
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-carmeva.c

@@ -57,13 +57,15 @@ static void __init carmeva_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata carmeva_eth_data = {
+static struct macb_platform_data __initdata carmeva_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata carmeva_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata carmeva_udc_data = {
@@ -75,8 +77,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 // static struct at91_cf_data __initdata carmeva_cf_data = {
 //	.det_pin	= AT91_PIN_PB0,
 //	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
+	// .irq_pin	= -EINVAL,
+	// .vcc_pin	= -EINVAL,
 // };
 
 static struct at91_mmc_data __initdata carmeva_mmc_data = {
@@ -84,6 +86,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PB10,
 	.wp_pin		= AT91_PIN_PC14,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {

arch/arm/mach-at91/board-cpu9krea.c

@@ -86,6 +86,8 @@ static void __init cpu9krea_init_early(void)
  */
 static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,13 +95,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
  */
 static struct at91_udc_data __initdata cpu9krea_udc_data = {
 	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata cpu9krea_macb_data = {
+static struct macb_platform_data __initdata cpu9krea_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -112,6 +115,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 #ifdef CONFIG_MACH_CPU9260
@@ -156,7 +160,7 @@ static struct sam9_smc_config __initdata cpu9krea_nand_smc_config = {
 
 static void __init cpu9krea_add_device_nand(void)
 {
-	sam9_smc_configure(3, &cpu9krea_nand_smc_config);
+	sam9_smc_configure(0, 3, &cpu9krea_nand_smc_config);
 	at91_add_device_nand(&cpu9krea_nand_data);
 }
 
@@ -238,7 +242,7 @@ static __init void cpu9krea_add_device_nor(void)
 	at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V);
 
 	/* configure chip-select 0 (NOR) */
-	sam9_smc_configure(0, &cpu9krea_nor_smc_config);
+	sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config);
 
 	platform_device_register(&cpu9krea_nor_flash);
 }
@@ -337,6 +341,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA29,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init cpu9krea_board_init(void)

arch/arm/mach-at91/board-cpuat91.c

@@ -82,12 +82,15 @@ static void __init cpuat91_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata cpuat91_eth_data = {
+static struct macb_platform_data __initdata cpuat91_eth_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata cpuat91_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata cpuat91_udc_data = {
@@ -98,6 +101,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 static struct at91_mmc_data __initdata cpuat91_mmc_data = {
 	.det_pin	= AT91_PIN_PC2,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {

arch/arm/mach-at91/board-csb337.c

@@ -58,18 +58,20 @@ static void __init csb337_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata csb337_eth_data = {
+static struct macb_platform_data __initdata csb337_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC2,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata csb337_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb337_udc_data = {
-	// this has no VBUS sensing pin
 	.pullup_pin	= AT91_PIN_PA24,
+	.vbus_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata csb337_i2c_devices[] = {
@@ -98,6 +100,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PD6,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info csb337_spi_devices[] = {

arch/arm/mach-at91/board-csb637.c

@@ -52,13 +52,15 @@ static void __init csb637_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata csb637_eth_data = {
+static struct macb_platform_data __initdata csb637_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC0,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata csb637_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb637_udc_data = {

arch/arm/mach-at91/board-dt.c

@@ -50,6 +50,7 @@ static void __init ek_init_early(void)
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 };
@@ -82,7 +83,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }

arch/arm/mach-at91/board-eb9200.c

@@ -60,13 +60,15 @@ static void __init eb9200_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata eb9200_eth_data = {
+static struct macb_platform_data __initdata eb9200_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata eb9200_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eb9200_udc_data = {
@@ -75,15 +77,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
 };
 
 static struct at91_cf_data __initdata eb9200_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 static struct at91_mmc_data __initdata eb9200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

arch/arm/mach-at91/board-ecbat91.c

@@ -64,18 +64,23 @@ static void __init ecb_at91init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata ecb_at91eth_data = {
+static struct macb_platform_data __initdata ecb_at91eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata ecb_at91mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-eco920.c

@@ -47,13 +47,15 @@ static void __init eco920_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata eco920_eth_data = {
+static struct macb_platform_data __initdata eco920_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC2,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata eco920_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eco920_udc_data = {
@@ -64,6 +66,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 static struct at91_mmc_data __initdata eco920_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 0,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data eco920_flash_data = {

arch/arm/mach-at91/board-flexibity.c

@@ -52,12 +52,14 @@ static void __init flexibity_init_early(void)
 /* USB Host port */
 static struct at91_usbh_data __initdata flexibity_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /* USB Device port */
 static struct at91_udc_data __initdata flexibity_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /* SPI devices */
@@ -76,6 +78,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
 	.wp_pin		= AT91_PIN_PC4,
+	.vcc_pin	= -EINVAL,
 };
 
 /* LEDs */

arch/arm/mach-at91/board-foxg20.c

@@ -106,6 +106,8 @@ static void __init foxg20_init_early(void)
  */
 static struct at91_usbh_data __initdata foxg20_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -113,7 +115,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
  */
 static struct at91_udc_data __initdata foxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -135,7 +137,7 @@ static struct spi_board_info foxg20_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata foxg20_macb_data = {
+static struct macb_platform_data __initdata foxg20_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -147,6 +149,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = {
 static struct at91_mmc_data __initdata foxg20_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-gsia18s.c

@@ -80,6 +80,8 @@ static void __init gsia18s_init_early(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -87,13 +89,13 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };
@@ -530,6 +532,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
 static struct at91_cf_data __initdata gsia18s_cf1_data = {
 	.irq_pin	= AT91_PIN_PA27,
 	.det_pin	= AT91_PIN_PB30,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PB31,
 	.chipselect	= 5,
 	.flags		= AT91_CF_TRUE_IDE,

arch/arm/mach-at91/board-kafa.c

@@ -61,13 +61,15 @@ static void __init kafa_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata kafa_eth_data = {
+static struct macb_platform_data __initdata kafa_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata kafa_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kafa_udc_data = {

arch/arm/mach-at91/board-kb9202.c

@@ -69,13 +69,15 @@ static void __init kb9202_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata kb9202_eth_data = {
+static struct macb_platform_data __initdata kb9202_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PB29,
 	.is_rmii	= 0,
 };
 
 static struct at91_usbh_data __initdata kb9202_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kb9202_udc_data = {
@@ -87,6 +89,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
 	.det_pin	= AT91_PIN_PB2,
 	.slot_b		= 0,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -100,7 +104,7 @@ static struct mtd_partition __initdata kb9202_nand_partition[] = {
 static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC29,
 	.enable_pin	= AT91_PIN_PC28,
 	.parts		= kb9202_nand_partition,

arch/arm/mach-at91/board-neocore926.c

@@ -72,6 +72,7 @@ static void __init neocore926_init_early(void)
 static struct at91_usbh_data __initdata neocore926_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
  */
 static struct at91_udc_data __initdata neocore926_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -149,13 +150,14 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata neocore926_macb_data = {
+static struct macb_platform_data __initdata neocore926_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -190,6 +192,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
 	.enable_pin		= AT91_PIN_PD15,
 	.parts			= neocore926_nand_partition,
 	.num_parts		= ARRAY_SIZE(neocore926_nand_partition),
+	.det_pin		= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
@@ -213,7 +216,7 @@ static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
 static void __init neocore926_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &neocore926_nand_smc_config);
+	sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
 
 	at91_add_device_nand(&neocore926_nand_data);
 }

arch/arm/mach-at91/board-pcontrol-g20.c

@@ -96,9 +96,9 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 static void __init add_device_pcontrol(void)
 {
 	/* configure chip-select 4 (IO compatible to 8051  X4 ) */
-	sam9_smc_configure(4, &pcontrol_smc_config[0]);
+	sam9_smc_configure(0, 4, &pcontrol_smc_config[0]);
 	/* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A  D4 ) */
-	sam9_smc_configure(7, &pcontrol_smc_config[1]);
+	sam9_smc_configure(0, 7, &pcontrol_smc_config[1]);
 }
 
 
@@ -107,6 +107,8 @@ static void __init add_device_pcontrol(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -122,7 +124,7 @@ static struct at91_udc_data __initdata pcontrol_g20_udc_data = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };

arch/arm/mach-at91/board-picotux200.c

@@ -60,13 +60,15 @@ static void __init picotux200_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata picotux200_eth_data = {
+static struct macb_platform_data __initdata picotux200_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
@@ -74,6 +76,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0

arch/arm/mach-at91/board-qil-a9260.c

@@ -77,6 +77,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -84,7 +86,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
@@ -104,7 +106,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA31,
 	.is_rmii	= 1,
 };
@@ -133,7 +135,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -161,7 +163,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -172,9 +174,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*
@@ -251,7 +253,7 @@ static void __init ek_board_init(void)
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	/* shutdown controller, wakeup button (5 msec low) */
-	at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
+	at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
 				| AT91_SHDW_RTTWKEN);
 }
 

arch/arm/mach-at91/board-rm9200dk.c

@@ -65,13 +65,15 @@ static void __init dk_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata dk_eth_data = {
+static struct macb_platform_data __initdata dk_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata dk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata dk_udc_data = {
@@ -80,16 +82,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
 };
 
 static struct at91_cf_data __initdata dk_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -143,7 +148,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
 	.cle		= 21,
 	.det_pin	= AT91_PIN_PB1,
 	.rdy_pin	= AT91_PIN_PC2,
-	// .enable_pin	= ... not there
+	.enable_pin	= -EINVAL,
 	.parts		= dk_nand_partition,
 	.num_parts	= ARRAY_SIZE(dk_nand_partition),
 };

arch/arm/mach-at91/board-rm9200ek.c

@@ -65,13 +65,15 @@ static void __init ek_init_early(void)
 	at91_set_serial_console(0);
 }
 
-static struct at91_eth_data __initdata ek_eth_data = {
+static struct macb_platform_data __initdata ek_eth_data = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {
@@ -85,6 +87,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

arch/arm/mach-at91/board-rsi-ews.c

@@ -60,7 +60,7 @@ static void __init rsi_ews_init_early(void)
 /*
  * Ethernet
  */
-static struct at91_eth_data rsi_ews_eth_data __initdata = {
+static struct macb_platform_data rsi_ews_eth_data __initdata = {
 	.phy_irq_pin	= AT91_PIN_PC4,
 	.is_rmii	= 1,
 };
@@ -70,6 +70,8 @@ static struct at91_eth_data rsi_ews_eth_data __initdata = {
  */
 static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*

arch/arm/mach-at91/board-sam9-l9260.c

@@ -72,6 +72,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -109,7 +111,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 0,
 };
@@ -134,7 +136,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -162,7 +164,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -176,7 +178,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC8,
 	.wp_pin		= AT91_PIN_PC4,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init ek_board_init(void)

arch/arm/mach-at91/board-sam9260ek.c

@@ -75,6 +75,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -151,7 +153,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -176,7 +178,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -211,7 +213,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -223,9 +225,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9261ek.c

@@ -131,7 +131,7 @@ static struct sam9_smc_config __initdata dm9000_smc_config = {
 static void __init ek_add_device_dm9000(void)
 {
 	/* Configure chip-select 2 (DM9000) */
-	sam9_smc_configure(2, &dm9000_smc_config);
+	sam9_smc_configure(0, 2, &dm9000_smc_config);
 
 	/* Configure Reset signal as output */
 	at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -151,6 +151,8 @@ static void __init ek_add_device_dm9000(void) {}
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -159,7 +161,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -182,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -217,7 +219,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -345,6 +347,9 @@ static struct spi_board_info ek_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */

arch/arm/mach-at91/board-sam9263ek.c

@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -151,14 +152,14 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,
@@ -218,7 +219,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9g20ek.c

@@ -86,6 +86,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -123,7 +125,7 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
 	.is_rmii	= 1,
 };
@@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -195,7 +198,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= -EINVAL,
 	},
 
 };
@@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
 #else

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -69,6 +69,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -100,6 +101,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -EINVAL,
 	},
 };
 
@@ -115,7 +117,7 @@ static struct mci_platform_data __initdata mci1_data = {
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PD5,
 	.is_rmii	= 1,
 };
@@ -143,6 +145,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -175,7 +178,7 @@ static void __init ek_add_device_nand(void)
 		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
 
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -330,6 +333,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9rlek.c

@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -91,7 +91,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.parts		= ek_nand_partition,
@@ -119,7 +119,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = {
 static void __init ek_add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
+	sam9_smc_configure(0, 3, &ek_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -204,6 +204,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-snapper9260.c

@@ -57,15 +57,19 @@ static void __init snapper9260_init_early(void)
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata snapper9260_udc_data = {
 	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
 	.vbus_active_low	= 1,
 	.vbus_polled		= 1,
+	.pullup_pin		= -EINVAL,
 };
 
-static struct at91_eth_data snapper9260_macb_data = {
+static struct macb_platform_data snapper9260_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -104,6 +108,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
 	.parts		= snapper9260_nand_partitions,
 	.num_parts	= ARRAY_SIZE(snapper9260_nand_partitions),
 	.bus_width_16	= 0,
+	.enable_pin	= -EINVAL,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {
@@ -149,7 +155,7 @@ static struct i2c_board_info __initdata snapper9260_i2c_devices[] = {
 static void __init snapper9260_add_device_nand(void)
 {
 	at91_set_A_periph(AT91_PIN_PC14, 0);
-	sam9_smc_configure(3, &snapper9260_nand_smc_config);
+	sam9_smc_configure(0, 3, &snapper9260_nand_smc_config);
 	at91_add_device_nand(&snapper9260_nand_data);
 }
 

arch/arm/mach-at91/board-stamp9g20.c

@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata nand_smc_config = {
@@ -108,7 +109,7 @@ static struct sam9_smc_config __initdata nand_smc_config = {
 static void __init add_device_nand(void)
 {
 	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &nand_smc_config);
+	sam9_smc_configure(0, 3, &nand_smc_config);
 
 	at91_add_device_nand(&nand_data);
 }
@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+		.detect_pin	= -1,
+		.wp_pin		= -1,
 	},
 };
 #else
 static struct at91_mmc_data __initdata mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -137,6 +143,8 @@ static struct at91_mmc_data __initdata mmc_data = {
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -145,19 +153,19 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata macb_data = {
+static struct macb_platform_data __initdata macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA28,
 	.is_rmii	= 1,
 };

arch/arm/mach-at91/board-usb-a926x.c

@@ -66,6 +66,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -73,7 +75,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB11,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static void __init ek_add_device_udc(void)
@@ -146,7 +148,7 @@ static void __init ek_add_device_spi(void)
 /*
  * MACB Ethernet device
  */
-static struct at91_eth_data __initdata ek_macb_data = {
+static struct macb_platform_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PE31,
 	.is_rmii	= 1,
 };
@@ -193,7 +195,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,
@@ -245,9 +247,9 @@ static void __init ek_add_device_nand(void)
 
 	/* configure chip-select 3 (NAND) */
 	if (machine_is_usb_a9g20())
-		sam9_smc_configure(3, &usb_a9g20_nand_smc_config);
+		sam9_smc_configure(0, 3, &usb_a9g20_nand_smc_config);
 	else
-		sam9_smc_configure(3, &usb_a9260_nand_smc_config);
+		sam9_smc_configure(0, 3, &usb_a9260_nand_smc_config);
 
 	at91_add_device_nand(&ek_nand_data);
 }
@@ -344,7 +346,7 @@ static void __init ek_board_init(void)
 		/* I2C */
 		at91_add_device_i2c(NULL, 0);
 		/* shutdown controller, wakeup button (5 msec low) */
-		at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
+		at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10)
 				| AT91_SHDW_WKMODE0_LOW
 				| AT91_SHDW_RTTWKEN);
 	}

arch/arm/mach-at91/board-yl-9200.c

@@ -110,7 +110,7 @@ static struct gpio_led yl9200_leds[] = {
 /*
  * Ethernet
  */
-static struct at91_eth_data __initdata yl9200_eth_data = {
+static struct macb_platform_data __initdata yl9200_eth_data = {
 	.phy_irq_pin		= AT91_PIN_PB28,
 	.is_rmii		= 1,
 };
@@ -120,6 +120,8 @@ static struct at91_eth_data __initdata yl9200_eth_data = {
  */
 static struct at91_usbh_data __initdata yl9200_usbh_data = {
 	.ports			= 1,	/* PQFP version of AT91RM9200 */
+	.vbus_pin		= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -137,8 +139,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
  */
 static struct at91_mmc_data __initdata yl9200_mmc_data = {
 	.det_pin	= AT91_PIN_PB9,
-	// .wp_pin	= ... not connected
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*
@@ -175,7 +178,7 @@ static struct mtd_partition __initdata yl9200_nand_partition[] = {
 static struct atmel_nand_data __initdata yl9200_nand_data = {
 	.ale		= 6,
 	.cle		= 7,
-	// .det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
 	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.parts		= yl9200_nand_partition,

arch/arm/mach-at91/generic.h

@@ -29,6 +29,7 @@ extern void __init at91_aic_init(unsigned int priority[]);
  /* Timer */
 struct sys_timer;
 extern struct sys_timer at91rm9200_timer;
+extern void at91sam926x_ioremap_pit(u32 addr);
 extern struct sys_timer at91sam926x_timer;
 extern struct sys_timer at91x40_timer;
 
@@ -57,7 +58,10 @@ extern void at91_irq_suspend(void);
 extern void at91_irq_resume(void);
 
 /* reset */
-extern void at91sam9_alt_reset(void);
+extern void at91sam9_alt_restart(char, const char *);
+
+/* shutdown */
+extern void at91_ioremap_shdwc(u32 base_addr);
 
  /* GPIO */
 #define AT91RM9200_PQFP		3	/* AT91RM9200 PQFP package has 3 banks */
@@ -65,11 +69,9 @@ extern void at91sam9_alt_reset(void);
 
 struct at91_gpio_bank {
 	unsigned short id;		/* peripheral ID */
-	unsigned long offset;		/* offset from system peripheral base */
-	struct clk *clock;		/* associated clock */
+	unsigned long regbase;		/* offset from system peripheral base */
 };
 extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks);
 extern void __init at91_gpio_irq_setup(void);
 
-extern void (*at91_arch_reset)(void);
 extern int at91_extern_irq;

arch/arm/mach-at91/gpio.c

@@ -29,8 +29,9 @@
 struct at91_gpio_chip {
 	struct gpio_chip	chip;
 	struct at91_gpio_chip	*next;		/* Bank sharing same clock */
-	struct at91_gpio_bank	*bank;		/* Bank definition */
+	int			id;		/* ID of register bank */
 	void __iomem		*regbase;	/* Base of register bank */
+	struct clk		*clock;		/* associated clock */
 };
 
 #define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
@@ -58,18 +59,17 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip,
 	}
 
 static struct at91_gpio_chip gpio_chip[] = {
-	AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32),
-	AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32),
+	AT91_GPIO_CHIP("pioA", 0x00, 32),
+	AT91_GPIO_CHIP("pioB", 0x20, 32),
+	AT91_GPIO_CHIP("pioC", 0x40, 32),
+	AT91_GPIO_CHIP("pioD", 0x60, 32),
+	AT91_GPIO_CHIP("pioE", 0x80, 32),
 };
 
 static int gpio_banks;
 
 static inline void __iomem *pin_to_controller(unsigned pin)
 {
-	pin -= PIN_BASE;
 	pin /= 32;
 	if (likely(pin < gpio_banks))
 		return gpio_chip[pin].regbase;
@@ -79,7 +79,6 @@ static inline void __iomem *pin_to_controller(unsigned pin)
 
 static inline unsigned pin_to_mask(unsigned pin)
 {
-	pin -= PIN_BASE;
 	return 1 << (pin % 32);
 }
 
@@ -274,8 +273,9 @@ static u32 backups[MAX_GPIO_BANKS];
 
 static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
 {
-	unsigned	mask = pin_to_mask(d->irq);
-	unsigned	bank = (d->irq - PIN_BASE) / 32;
+	unsigned	pin = irq_to_gpio(d->irq);
+	unsigned	mask = pin_to_mask(pin);
+	unsigned	bank = pin / 32;
 
 	if (unlikely(bank >= MAX_GPIO_BANKS))
 		return -EINVAL;
@@ -285,7 +285,7 @@ static int gpio_irq_set_wake(struct irq_data *d, unsigned state)
 	else
 		wakeups[bank] &= ~mask;
 
-	irq_set_irq_wake(gpio_chip[bank].bank->id, state);
+	irq_set_irq_wake(gpio_chip[bank].id, state);
 
 	return 0;
 }
@@ -302,7 +302,7 @@ void at91_gpio_suspend(void)
 		__raw_writel(wakeups[i], pio + PIO_IER);
 
 		if (!wakeups[i])
-			clk_disable(gpio_chip[i].bank->clock);
+			clk_disable(gpio_chip[i].clock);
 		else {
 #ifdef CONFIG_PM_DEBUG
 			printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]);
@@ -319,7 +319,7 @@ void at91_gpio_resume(void)
 		void __iomem	*pio = gpio_chip[i].regbase;
 
 		if (!wakeups[i])
-			clk_enable(gpio_chip[i].bank->clock);
+			clk_enable(gpio_chip[i].clock);
 
 		__raw_writel(wakeups[i], pio + PIO_IDR);
 		__raw_writel(backups[i], pio + PIO_IER);
@@ -344,8 +344,9 @@ void at91_gpio_resume(void)
 
 static void gpio_irq_mask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IDR);
@@ -353,8 +354,9 @@ static void gpio_irq_mask(struct irq_data *d)
 
 static void gpio_irq_unmask(struct irq_data *d)
 {
-	void __iomem	*pio = pin_to_controller(d->irq);
-	unsigned	mask = pin_to_mask(d->irq);
+	unsigned	pin = irq_to_gpio(d->irq);
+	void __iomem	*pio = pin_to_controller(pin);
+	unsigned	mask = pin_to_mask(pin);
 
 	if (pio)
 		__raw_writel(mask, pio + PIO_IER);
@@ -382,7 +384,7 @@ static struct irq_chip gpio_irqchip = {
 
 static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 {
-	unsigned	pin;
+	unsigned	irq_pin;
 	struct irq_data *idata = irq_desc_get_irq_data(desc);
 	struct irq_chip *chip = irq_data_get_irq_chip(idata);
 	struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata);
@@ -405,12 +407,12 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
 			continue;
 		}
 
-		pin = at91_gpio->chip.base;
+		irq_pin = gpio_to_irq(at91_gpio->chip.base);
 
 		while (isr) {
 			if (isr & 1)
-				generic_handle_irq(pin);
-			pin++;
+				generic_handle_irq(irq_pin);
+			irq_pin++;
 			isr >>= 1;
 		}
 	}
@@ -438,7 +440,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused)
 		seq_printf(s, "%i:\t", j);
 
 		for (bank = 0; bank < gpio_banks; bank++) {
-			unsigned	pin  = PIN_BASE + (32 * bank) + j;
+			unsigned	pin  = (32 * bank) + j;
 			void __iomem	*pio = pin_to_controller(pin);
 			unsigned	mask = pin_to_mask(pin);
 
@@ -491,27 +493,28 @@ static struct lock_class_key gpio_lock_class;
  */
 void __init at91_gpio_irq_setup(void)
 {
-	unsigned		pioc, pin;
+	unsigned		pioc, irq = gpio_to_irq(0);
 	struct at91_gpio_chip	*this, *prev;
 
-	for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL;
+	for (pioc = 0, this = gpio_chip, prev = NULL;
 			pioc++ < gpio_banks;
 			prev = this, this++) {
-		unsigned	id = this->bank->id;
+		unsigned	id = this->id;
 		unsigned	i;
 
 		__raw_writel(~0, this->regbase + PIO_IDR);
 
-		for (i = 0, pin = this->chip.base; i < 32; i++, pin++) {
-			irq_set_lockdep_class(pin, &gpio_lock_class);
+		for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32;
+		     i++, irq++) {
+			irq_set_lockdep_class(irq, &gpio_lock_class);
 
 			/*
 			 * Can use the "simple" and not "edge" handler since it's
 			 * shorter, and the AIC handles interrupts sanely.
 			 */
-			irq_set_chip_and_handler(pin, &gpio_irqchip,
+			irq_set_chip_and_handler(irq, &gpio_irqchip,
 						 handle_simple_irq);
-			set_irq_flags(pin, IRQF_VALID);
+			set_irq_flags(irq, IRQF_VALID);
 		}
 
 		/* The toplevel handler handles one bank of GPIOs, except
@@ -524,7 +527,7 @@ void __init at91_gpio_irq_setup(void)
 		irq_set_chip_data(id, this);
 		irq_set_chained_handler(id, gpio_irq_handler);
 	}
-	pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks);
+	pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks);
 }
 
 /* gpiolib support */
@@ -612,16 +615,26 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
 	for (i = 0; i < nr_banks; i++) {
 		at91_gpio = &gpio_chip[i];
 
-		at91_gpio->bank = &data[i];
-		at91_gpio->chip.base = PIN_BASE + i * 32;
-		at91_gpio->regbase = at91_gpio->bank->offset +
-			(void __iomem *)AT91_VA_BASE_SYS;
+		at91_gpio->id = data[i].id;
+		at91_gpio->chip.base = i * 32;
+
+		at91_gpio->regbase = ioremap(data[i].regbase, 512);
+		if (!at91_gpio->regbase) {
+			pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i);
+			continue;
+		}
+
+		at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label);
+		if (!at91_gpio->clock) {
+			pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", i);
+			continue;
+		}
 
 		/* enable PIO controller's clock */
-		clk_enable(at91_gpio->bank->clock);
+		clk_enable(at91_gpio->clock);
 
 		/* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
-		if (last && last->bank->id == at91_gpio->bank->id)
+		if (last && last->id == at91_gpio->id)
 			last->next = at91_gpio;
 		last = at91_gpio;
 

arch/arm/mach-at91/include/mach/at91_aic.h

@@ -16,7 +16,19 @@
 #ifndef AT91_AIC_H
 #define AT91_AIC_H
 
-#define AT91_AIC_SMR(n)		(AT91_AIC + ((n) * 4))	/* Source Mode Registers 0-31 */
+#ifndef __ASSEMBLY__
+extern void __iomem *at91_aic_base;
+
+#define at91_aic_read(field) \
+	__raw_readl(at91_aic_base + field)
+
+#define at91_aic_write(field, value) \
+	__raw_writel(value, at91_aic_base + field);
+#else
+.extern at91_aic_base
+#endif
+
+#define AT91_AIC_SMR(n)		((n) * 4)		/* Source Mode Registers 0-31 */
 #define		AT91_AIC_PRIOR		(7 << 0)		/* Priority Level */
 #define		AT91_AIC_SRCTYPE	(3 << 5)		/* Interrupt Source Type */
 #define			AT91_AIC_SRCTYPE_LOW		(0 << 5)
@@ -24,30 +36,30 @@
 #define			AT91_AIC_SRCTYPE_HIGH		(2 << 5)
 #define			AT91_AIC_SRCTYPE_RISING		(3 << 5)
 
-#define AT91_AIC_SVR(n)		(AT91_AIC + 0x80 + ((n) * 4))	/* Source Vector Registers 0-31 */
-#define AT91_AIC_IVR		(AT91_AIC + 0x100)	/* Interrupt Vector Register */
-#define AT91_AIC_FVR		(AT91_AIC + 0x104)	/* Fast Interrupt Vector Register */
-#define AT91_AIC_ISR		(AT91_AIC + 0x108)	/* Interrupt Status Register */
+#define AT91_AIC_SVR(n)		(0x80 + ((n) * 4))	/* Source Vector Registers 0-31 */
+#define AT91_AIC_IVR		0x100			/* Interrupt Vector Register */
+#define AT91_AIC_FVR		0x104			/* Fast Interrupt Vector Register */
+#define AT91_AIC_ISR		0x108			/* Interrupt Status Register */
 #define		AT91_AIC_IRQID		(0x1f << 0)		/* Current Interrupt Identifier */
 
-#define AT91_AIC_IPR		(AT91_AIC + 0x10c)	/* Interrupt Pending Register */
-#define AT91_AIC_IMR		(AT91_AIC + 0x110)	/* Interrupt Mask Register */
-#define AT91_AIC_CISR		(AT91_AIC + 0x114)	/* Core Interrupt Status Register */
+#define AT91_AIC_IPR		0x10c			/* Interrupt Pending Register */
+#define AT91_AIC_IMR		0x110			/* Interrupt Mask Register */
+#define AT91_AIC_CISR		0x114			/* Core Interrupt Status Register */
 #define		AT91_AIC_NFIQ		(1 << 0)		/* nFIQ Status */
 #define		AT91_AIC_NIRQ		(1 << 1)		/* nIRQ Status */
 
-#define AT91_AIC_IECR		(AT91_AIC + 0x120)	/* Interrupt Enable Command Register */
-#define AT91_AIC_IDCR		(AT91_AIC + 0x124)	/* Interrupt Disable Command Register */
-#define AT91_AIC_ICCR		(AT91_AIC + 0x128)	/* Interrupt Clear Command Register */
-#define AT91_AIC_ISCR		(AT91_AIC + 0x12c)	/* Interrupt Set Command Register */
-#define AT91_AIC_EOICR		(AT91_AIC + 0x130)	/* End of Interrupt Command Register */
-#define AT91_AIC_SPU		(AT91_AIC + 0x134)	/* Spurious Interrupt Vector Register */
-#define AT91_AIC_DCR		(AT91_AIC + 0x138)	/* Debug Control Register */
+#define AT91_AIC_IECR		0x120			/* Interrupt Enable Command Register */
+#define AT91_AIC_IDCR		0x124			/* Interrupt Disable Command Register */
+#define AT91_AIC_ICCR		0x128			/* Interrupt Clear Command Register */
+#define AT91_AIC_ISCR		0x12c			/* Interrupt Set Command Register */
+#define AT91_AIC_EOICR		0x130			/* End of Interrupt Command Register */
+#define AT91_AIC_SPU		0x134			/* Spurious Interrupt Vector Register */
+#define AT91_AIC_DCR		0x138			/* Debug Control Register */
 #define		AT91_AIC_DCR_PROT	(1 << 0)		/* Protection Mode */
 #define		AT91_AIC_DCR_GMSK	(1 << 1)		/* General Mask */
 
-#define AT91_AIC_FFER		(AT91_AIC + 0x140)	/* Fast Forcing Enable Register [SAM9 only] */
-#define AT91_AIC_FFDR		(AT91_AIC + 0x144)	/* Fast Forcing Disable Register [SAM9 only] */
-#define AT91_AIC_FFSR		(AT91_AIC + 0x148)	/* Fast Forcing Status Register [SAM9 only] */
+#define AT91_AIC_FFER		0x140			/* Fast Forcing Enable Register [SAM9 only] */
+#define AT91_AIC_FFDR		0x144			/* Fast Forcing Disable Register [SAM9 only] */
+#define AT91_AIC_FFSR		0x148			/* Fast Forcing Status Register [SAM9 only] */
 
 #endif

arch/arm/mach-at91/include/mach/at91_dbgu.h

@@ -19,7 +19,7 @@
 #define dbgu_readl(dbgu, field) \
 	__raw_readl(AT91_VA_BASE_SYS + dbgu + AT91_DBGU_ ## field)
 
-#ifdef AT91_DBGU
+#if !defined(CONFIG_ARCH_AT91X40)
 #define AT91_DBGU_CR		(0x00)	/* Control Register */
 #define AT91_DBGU_MR		(0x04)	/* Mode Register */
 #define AT91_DBGU_IER		(0x08)	/* Interrupt Enable Register */