[ARM] pxa: use __raw_writel()/__raw_readl() for ssp_xxxx()

1. change SSP register definitions from absolute virtual addresses to
   offsets

2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()

Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-pxa/ssp.c

@@ -48,9 +48,11 @@
 static irqreturn_t ssp_interrupt(int irq, void *dev_id)
 {
 	struct ssp_dev *dev = (struct ssp_dev*) dev_id;
-	unsigned int status = SSSR_P(dev->port);
+	struct ssp_device *ssp = dev->ssp;
+	unsigned int status;
 
-	SSSR_P(dev->port) = status; /* clear status bits */
+	status = __raw_readl(ssp->mmio_base + SSSR);
+	__raw_writel(status, ssp->mmio_base + SSSR);
 
 	if (status & SSSR_ROR)
 		printk(KERN_WARNING "SSP(%d): receiver overrun\n", dev->port);
@@ -79,15 +81,16 @@ static irqreturn_t ssp_interrupt(int irq, void *dev_id)
  */
 int ssp_write_word(struct ssp_dev *dev, u32 data)
 {
+	struct ssp_device *ssp = dev->ssp;
 	int timeout = TIMEOUT;
 
-	while (!(SSSR_P(dev->port) & SSSR_TNF)) {
+	while (!(__raw_readl(ssp->mmio_base + SSSR) & SSSR_TNF)) {
 	        if (!--timeout)
 	        	return -ETIMEDOUT;
 		cpu_relax();
 	}
 
-	SSDR_P(dev->port) = data;
+	__raw_writel(data, ssp->mmio_base + SSDR);
 
 	return 0;
 }
@@ -109,15 +112,16 @@ int ssp_write_word(struct ssp_dev *dev, u32 data)
  */
 int ssp_read_word(struct ssp_dev *dev, u32 *data)
 {
+	struct ssp_device *ssp = dev->ssp;
 	int timeout = TIMEOUT;
 
-	while (!(SSSR_P(dev->port) & SSSR_RNE)) {
+	while (!(__raw_readl(ssp->mmio_base + SSSR) & SSSR_RNE)) {
 	        if (!--timeout)
 	        	return -ETIMEDOUT;
 		cpu_relax();
 	}
 
-	*data = SSDR_P(dev->port);
+	*data = __raw_readl(ssp->mmio_base + SSDR);
 	return 0;
 }
 
@@ -131,17 +135,18 @@ int ssp_read_word(struct ssp_dev *dev, u32 *data)
  */
 int ssp_flush(struct ssp_dev *dev)
 {
+	struct ssp_device *ssp = dev->ssp;
 	int timeout = TIMEOUT * 2;
 
 	do {
-		while (SSSR_P(dev->port) & SSSR_RNE) {
+		while (__raw_readl(ssp->mmio_base + SSSR) & SSSR_RNE) {
 		        if (!--timeout)
 		        	return -ETIMEDOUT;
-			(void) SSDR_P(dev->port);
+			(void)__raw_readl(ssp->mmio_base + SSDR);
 		}
 	        if (!--timeout)
 	        	return -ETIMEDOUT;
-	} while (SSSR_P(dev->port) & SSSR_BSY);
+	} while (__raw_readl(ssp->mmio_base + SSSR) & SSSR_BSY);
 
 	return 0;
 }
@@ -153,7 +158,12 @@ int ssp_flush(struct ssp_dev *dev)
  */
 void ssp_enable(struct ssp_dev *dev)
 {
-	SSCR0_P(dev->port) |= SSCR0_SSE;
+	struct ssp_device *ssp = dev->ssp;
+	uint32_t sscr0;
+
+	sscr0 = __raw_readl(ssp->mmio_base + SSCR0);
+	sscr0 |= SSCR0_SSE;
+	__raw_writel(sscr0, ssp->mmio_base + SSCR0);
 }
 
 /**
@@ -163,7 +173,12 @@ void ssp_enable(struct ssp_dev *dev)
  */
 void ssp_disable(struct ssp_dev *dev)
 {
-	SSCR0_P(dev->port) &= ~SSCR0_SSE;
+	struct ssp_device *ssp = dev->ssp;
+	uint32_t sscr0;
+
+	sscr0 = __raw_readl(ssp->mmio_base + SSCR0);
+	sscr0 &= ~SSCR0_SSE;
+	__raw_writel(sscr0, ssp->mmio_base + SSCR0);
 }
 
 /**
@@ -172,14 +187,16 @@ void ssp_disable(struct ssp_dev *dev)
  *
  * Save the configured SSP state for suspend.
  */
-void ssp_save_state(struct ssp_dev *dev, struct ssp_state *ssp)
+void ssp_save_state(struct ssp_dev *dev, struct ssp_state *state)
 {
-	ssp->cr0 = SSCR0_P(dev->port);
-	ssp->cr1 = SSCR1_P(dev->port);
-	ssp->to = SSTO_P(dev->port);
-	ssp->psp = SSPSP_P(dev->port);
+	struct ssp_device *ssp = dev->ssp;
+
+	state->cr0 = __raw_readl(ssp->mmio_base + SSCR0);
+	state->cr1 = __raw_readl(ssp->mmio_base + SSCR1);
+	state->to  = __raw_readl(ssp->mmio_base + SSTO);
+	state->psp = __raw_readl(ssp->mmio_base + SSPSP);
 
-	SSCR0_P(dev->port) &= ~SSCR0_SSE;
+	ssp_disable(dev);
 }
 
 /**
@@ -188,16 +205,18 @@ void ssp_save_state(struct ssp_dev *dev, struct ssp_state *ssp)
  *
  * Restore the SSP configuration saved previously by ssp_save_state.
  */
-void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *ssp)
+void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *state)
 {
-	SSSR_P(dev->port) = SSSR_ROR | SSSR_TUR | SSSR_BCE;
+	struct ssp_device *ssp = dev->ssp;
+	uint32_t sssr = SSSR_ROR | SSSR_TUR | SSSR_BCE;
 
-	SSCR0_P(dev->port) = ssp->cr0 & ~SSCR0_SSE;
-	SSCR1_P(dev->port) = ssp->cr1;
-	SSTO_P(dev->port) = ssp->to;
-	SSPSP_P(dev->port) = ssp->psp;
+	__raw_writel(sssr, ssp->mmio_base + SSSR);
 
-	SSCR0_P(dev->port) = ssp->cr0;
+	__raw_writel(state->cr0 & ~SSCR0_SSE, ssp->mmio_base + SSCR0);
+	__raw_writel(state->cr1, ssp->mmio_base + SSCR1);
+	__raw_writel(state->to,  ssp->mmio_base + SSTO);
+	__raw_writel(state->psp, ssp->mmio_base + SSPSP);
+	__raw_writel(state->cr0, ssp->mmio_base + SSCR0);
 }
 
 /**
@@ -211,15 +230,17 @@ void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *ssp)
  */
 int ssp_config(struct ssp_dev *dev, u32 mode, u32 flags, u32 psp_flags, u32 speed)
 {
+	struct ssp_device *ssp = dev->ssp;
+
 	dev->mode = mode;
 	dev->flags = flags;
 	dev->psp_flags = psp_flags;
 	dev->speed = speed;
 
 	/* set up port type, speed, port settings */
-	SSCR0_P(dev->port) = (dev->speed | dev->mode);
-	SSCR1_P(dev->port) = dev->flags;
-	SSPSP_P(dev->port) = dev->psp_flags;
+	__raw_writel((dev->speed | dev->mode), ssp->mmio_base + SSCR0);
+	__raw_writel(dev->flags, ssp->mmio_base + SSCR1);
+	__raw_writel(dev->psp_flags, ssp->mmio_base + SSPSP);
 
 	return 0;
 }
@@ -274,7 +295,7 @@ void ssp_exit(struct ssp_dev *dev)
 {
 	struct ssp_device *ssp = dev->ssp;
 
-	SSCR0_P(dev->port) &= ~SSCR0_SSE;
+	ssp_disable(dev);
 	free_irq(dev->irq, dev);
 	clk_disable(ssp->clk);
 	ssp_free(ssp);

include/asm-arm/arch-pxa/regs-ssp.h

@@ -7,7 +7,20 @@
  * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
  */
 
- /* Common PXA2xx bits first */
+#define SSCR0		(0x00)  /* SSP Control Register 0 */
+#define SSCR1		(0x04)  /* SSP Control Register 1 */
+#define SSSR		(0x08)  /* SSP Status Register */
+#define SSITR		(0x0C)  /* SSP Interrupt Test Register */
+#define SSDR		(0x10)  /* SSP Data Write/Data Read Register */
+
+#define SSTO		(0x28)  /* SSP Time Out Register */
+#define SSPSP		(0x2C)  /* SSP Programmable Serial Protocol */
+#define SSTSA		(0x30)  /* SSP Tx Timeslot Active */
+#define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
+#define SSTSS		(0x38)  /* SSP Timeslot Status */
+#define SSACD		(0x3C)  /* SSP Audio Clock Divider */
+
+/* Common PXA2xx bits first */
 #define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
 #define SSCR0_DataSize(x)  ((x) - 1)	/* Data Size Select [4..16] */
 #define SSCR0_FRF	(0x00000030)	/* FRame Format (mask) */
@@ -96,78 +109,4 @@
 #define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
 #define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
 
-#define SSCR0_P1	__REG(0x41000000)  /* SSP Port 1 Control Register 0 */
-#define SSCR1_P1	__REG(0x41000004)  /* SSP Port 1 Control Register 1 */
-#define SSSR_P1		__REG(0x41000008)  /* SSP Port 1 Status Register */
-#define SSITR_P1	__REG(0x4100000C)  /* SSP Port 1 Interrupt Test Register */
-#define SSDR_P1		__REG(0x41000010)  /* (Write / Read) SSP Port 1 Data Write Register/SSP Data Read Register */
-
-/* Support existing PXA25x drivers */
-#define SSCR0		SSCR0_P1  /* SSP Control Register 0 */
-#define SSCR1		SSCR1_P1  /* SSP Control Register 1 */
-#define SSSR		SSSR_P1	  /* SSP Status Register */
-#define SSITR		SSITR_P1  /* SSP Interrupt Test Register */
-#define SSDR		SSDR_P1	  /* (Write / Read) SSP Data Write Register/SSP Data Read Register */
-
-/* PXA27x ports */
-#if defined (CONFIG_PXA27x)
-#define SSTO_P1		__REG(0x41000028)  /* SSP Port 1 Time Out Register */
-#define SSPSP_P1	__REG(0x4100002C)  /* SSP Port 1 Programmable Serial Protocol */
-#define SSTSA_P1	__REG(0x41000030)  /* SSP Port 1 Tx Timeslot Active */
-#define SSRSA_P1	__REG(0x41000034)  /* SSP Port 1 Rx Timeslot Active */
-#define SSTSS_P1	__REG(0x41000038)  /* SSP Port 1 Timeslot Status */
-#define SSACD_P1	__REG(0x4100003C)  /* SSP Port 1 Audio Clock Divider */
-#define SSCR0_P2	__REG(0x41700000)  /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2	__REG(0x41700004)  /* SSP Port 2 Control Register 1 */
-#define SSSR_P2		__REG(0x41700008)  /* SSP Port 2 Status Register */
-#define SSITR_P2	__REG(0x4170000C)  /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2		__REG(0x41700010)  /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2		__REG(0x41700028)  /* SSP Port 2 Time Out Register */
-#define SSPSP_P2	__REG(0x4170002C)  /* SSP Port 2 Programmable Serial Protocol */
-#define SSTSA_P2	__REG(0x41700030)  /* SSP Port 2 Tx Timeslot Active */
-#define SSRSA_P2	__REG(0x41700034)  /* SSP Port 2 Rx Timeslot Active */
-#define SSTSS_P2	__REG(0x41700038)  /* SSP Port 2 Timeslot Status */
-#define SSACD_P2	__REG(0x4170003C)  /* SSP Port 2 Audio Clock Divider */
-#define SSCR0_P3	__REG(0x41900000)  /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3	__REG(0x41900004)  /* SSP Port 3 Control Register 1 */
-#define SSSR_P3		__REG(0x41900008)  /* SSP Port 3 Status Register */
-#define SSITR_P3	__REG(0x4190000C)  /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3		__REG(0x41900010)  /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3		__REG(0x41900028)  /* SSP Port 3 Time Out Register */
-#define SSPSP_P3	__REG(0x4190002C)  /* SSP Port 3 Programmable Serial Protocol */
-#define SSTSA_P3	__REG(0x41900030)  /* SSP Port 3 Tx Timeslot Active */
-#define SSRSA_P3	__REG(0x41900034)  /* SSP Port 3 Rx Timeslot Active */
-#define SSTSS_P3	__REG(0x41900038)  /* SSP Port 3 Timeslot Status */
-#define SSACD_P3	__REG(0x4190003C)  /* SSP Port 3 Audio Clock Divider */
-#else /* PXA255 (only port 2) and PXA26x ports*/
-#define SSTO_P1		__REG(0x41000028)  /* SSP Port 1 Time Out Register */
-#define SSPSP_P1	__REG(0x4100002C)  /* SSP Port 1 Programmable Serial Protocol */
-#define SSCR0_P2	__REG(0x41400000)  /* SSP Port 2 Control Register 0 */
-#define SSCR1_P2	__REG(0x41400004)  /* SSP Port 2 Control Register 1 */
-#define SSSR_P2		__REG(0x41400008)  /* SSP Port 2 Status Register */
-#define SSITR_P2	__REG(0x4140000C)  /* SSP Port 2 Interrupt Test Register */
-#define SSDR_P2		__REG(0x41400010)  /* (Write / Read) SSP Port 2 Data Write Register/SSP Data Read Register */
-#define SSTO_P2		__REG(0x41400028)  /* SSP Port 2 Time Out Register */
-#define SSPSP_P2	__REG(0x4140002C)  /* SSP Port 2 Programmable Serial Protocol */
-#define SSCR0_P3	__REG(0x41500000)  /* SSP Port 3 Control Register 0 */
-#define SSCR1_P3	__REG(0x41500004)  /* SSP Port 3 Control Register 1 */
-#define SSSR_P3		__REG(0x41500008)  /* SSP Port 3 Status Register */
-#define SSITR_P3	__REG(0x4150000C)  /* SSP Port 3 Interrupt Test Register */
-#define SSDR_P3		__REG(0x41500010)  /* (Write / Read) SSP Port 3 Data Write Register/SSP Data Read Register */
-#define SSTO_P3		__REG(0x41500028)  /* SSP Port 3 Time Out Register */
-#define SSPSP_P3	__REG(0x4150002C)  /* SSP Port 3 Programmable Serial Protocol */
-#endif
-
-#define SSCR0_P(x) (*(((x) == 1) ? &SSCR0_P1 : ((x) == 2) ? &SSCR0_P2 : ((x) == 3) ? &SSCR0_P3 : NULL))
-#define SSCR1_P(x) (*(((x) == 1) ? &SSCR1_P1 : ((x) == 2) ? &SSCR1_P2 : ((x) == 3) ? &SSCR1_P3 : NULL))
-#define SSSR_P(x) (*(((x) == 1) ? &SSSR_P1 : ((x) == 2) ? &SSSR_P2 : ((x) == 3) ? &SSSR_P3 : NULL))
-#define SSITR_P(x) (*(((x) == 1) ? &SSITR_P1 : ((x) == 2) ? &SSITR_P2 : ((x) == 3) ? &SSITR_P3 : NULL))
-#define SSDR_P(x) (*(((x) == 1) ? &SSDR_P1 : ((x) == 2) ? &SSDR_P2 : ((x) == 3) ? &SSDR_P3 : NULL))
-#define SSTO_P(x) (*(((x) == 1) ? &SSTO_P1 : ((x) == 2) ? &SSTO_P2 : ((x) == 3) ? &SSTO_P3 : NULL))
-#define SSPSP_P(x) (*(((x) == 1) ? &SSPSP_P1 : ((x) == 2) ? &SSPSP_P2 : ((x) == 3) ? &SSPSP_P3 : NULL))
-#define SSTSA_P(x) (*(((x) == 1) ? &SSTSA_P1 : ((x) == 2) ? &SSTSA_P2 : ((x) == 3) ? &SSTSA_P3 : NULL))
-#define SSRSA_P(x) (*(((x) == 1) ? &SSRSA_P1 : ((x) == 2) ? &SSRSA_P2 : ((x) == 3) ? &SSRSA_P3 : NULL))
-#define SSTSS_P(x) (*(((x) == 1) ? &SSTSS_P1 : ((x) == 2) ? &SSTSS_P2 : ((x) == 3) ? &SSTSS_P3 : NULL))
-#define SSACD_P(x) (*(((x) == 1) ? &SSACD_P1 : ((x) == 2) ? &SSACD_P2 : ((x) == 3) ? &SSACD_P3 : NULL))
-
 #endif /* __ASM_ARCH_REGS_SSP_H */