iwlwifi: move some configuration parameters into DVM

There are a number of parameters that aren't really hardware
specific but rather define how the DVM firmware is used.
Move these into the DVM configuration.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

drivers/net/wireless/iwlwifi/dvm/agn.h

@@ -78,10 +78,13 @@
 /* device operations */
 extern struct iwl_dvm_cfg iwl_dvm_1000_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_2000_cfg;
+extern struct iwl_dvm_cfg iwl_dvm_105_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_2030_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_5000_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_5150_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_6000_cfg;
+extern struct iwl_dvm_cfg iwl_dvm_6005_cfg;
+extern struct iwl_dvm_cfg iwl_dvm_6050_cfg;
 extern struct iwl_dvm_cfg iwl_dvm_6030_cfg;
 
 
@@ -291,8 +294,8 @@ void iwlagn_bt_adjust_rssi_monitor(struct iwl_priv *priv, bool rssi_ena);
 
 static inline bool iwl_advanced_bt_coexist(struct iwl_priv *priv)
 {
-	return priv->cfg->bt_params &&
-	       priv->cfg->bt_params->advanced_bt_coexist;
+	return priv->lib->bt_params &&
+	       priv->lib->bt_params->advanced_bt_coexist;
 }
 
 #ifdef CONFIG_IWLWIFI_DEBUG

drivers/net/wireless/iwlwifi/dvm/calib.c

@@ -521,7 +521,7 @@ static int iwl_enhance_sensitivity_write(struct iwl_priv *priv)
 
 	iwl_prepare_legacy_sensitivity_tbl(priv, data, &cmd.enhance_table[0]);
 
-	if (priv->cfg->base_params->hd_v2) {
+	if (priv->lib->hd_v2) {
 		cmd.enhance_table[HD_INA_NON_SQUARE_DET_OFDM_INDEX] =
 			HD_INA_NON_SQUARE_DET_OFDM_DATA_V2;
 		cmd.enhance_table[HD_INA_NON_SQUARE_DET_CCK_INDEX] =
@@ -895,7 +895,7 @@ static void iwlagn_gain_computation(struct iwl_priv *priv,
 			continue;
 		}
 
-		delta_g = (priv->cfg->base_params->chain_noise_scale *
+		delta_g = (priv->lib->chain_noise_scale *
 			((s32)average_noise[default_chain] -
 			(s32)average_noise[i])) / 1500;
 
@@ -1051,8 +1051,8 @@ void iwl_chain_noise_calibration(struct iwl_priv *priv)
 		return;
 
 	/* Analyze signal for disconnected antenna */
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		/* Disable disconnected antenna algorithm for advanced
 		   bt coex, assuming valid antennas are connected */
 		data->active_chains = priv->nvm_data->valid_rx_ant;

drivers/net/wireless/iwlwifi/dvm/dev.h

@@ -568,16 +568,61 @@ struct iwl_hw_params {
 	const struct iwl_sensitivity_ranges *sens;
 };
 
+/**
+ * struct iwl_dvm_bt_params - DVM specific BT (coex) parameters
+ * @advanced_bt_coexist: support advanced bt coexist
+ * @bt_init_traffic_load: specify initial bt traffic load
+ * @bt_prio_boost: default bt priority boost value
+ * @agg_time_limit: maximum number of uSec in aggregation
+ * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
+ */
+struct iwl_dvm_bt_params {
+	bool advanced_bt_coexist;
+	u8 bt_init_traffic_load;
+	u32 bt_prio_boost;
+	u16 agg_time_limit;
+	bool bt_sco_disable;
+	bool bt_session_2;
+};
+
+/**
+ * struct iwl_dvm_cfg - DVM firmware specific device configuration
+ * @set_hw_params: set hardware parameters
+ * @set_channel_switch: send channel switch command
+ * @nic_config: apply device specific configuration
+ * @temperature: read temperature
+ * @adv_thermal_throttle: support advance thermal throttle
+ * @support_ct_kill_exit: support ct kill exit condition
+ * @plcp_delta_threshold: plcp error rate threshold used to trigger
+ *	radio tuning when there is a high receiving plcp error rate
+ * @chain_noise_scale: default chain noise scale used for gain computation
+ * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
+ * @no_idle_support: do not support idle mode
+ * @bt_params: pointer to BT parameters
+ * @need_temp_offset_calib: need to perform temperature offset calibration
+ * @no_xtal_calib: some devices do not need crystal calibration data,
+ *	don't send it to those
+ * @temp_offset_v2: support v2 of temperature offset calibration
+ * @adv_pm: advanced power management
+ */
 struct iwl_dvm_cfg {
-	/* set hw dependent parameters */
 	void (*set_hw_params)(struct iwl_priv *priv);
 	int (*set_channel_switch)(struct iwl_priv *priv,
 				  struct ieee80211_channel_switch *ch_switch);
-	/* device specific configuration */
 	void (*nic_config)(struct iwl_priv *priv);
-
-	/* temperature */
 	void (*temperature)(struct iwl_priv *priv);
+
+	const struct iwl_dvm_bt_params *bt_params;
+	s32 chain_noise_scale;
+	u8 plcp_delta_threshold;
+	bool adv_thermal_throttle;
+	bool support_ct_kill_exit;
+	bool hd_v2;
+	bool no_idle_support;
+	bool need_temp_offset_calib;
+	bool no_xtal_calib;
+	bool temp_offset_v2;
+	bool adv_pm;
 };
 
 struct iwl_wipan_noa_data {

drivers/net/wireless/iwlwifi/dvm/devices.c

@@ -178,6 +178,9 @@ struct iwl_dvm_cfg iwl_dvm_1000_cfg = {
 	.set_hw_params = iwl1000_hw_set_hw_params,
 	.nic_config = iwl1000_nic_config,
 	.temperature = iwlagn_temperature,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_EXT_LONG_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
 };
 
 
@@ -236,12 +239,52 @@ struct iwl_dvm_cfg iwl_dvm_2000_cfg = {
 	.set_hw_params = iwl2000_hw_set_hw_params,
 	.nic_config = iwl2000_nic_config,
 	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.hd_v2 = true,
+	.need_temp_offset_calib = true,
+	.temp_offset_v2 = true,
+};
+
+struct iwl_dvm_cfg iwl_dvm_105_cfg = {
+	.set_hw_params = iwl2000_hw_set_hw_params,
+	.nic_config = iwl2000_nic_config,
+	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.hd_v2 = true,
+	.need_temp_offset_calib = true,
+	.temp_offset_v2 = true,
+	.adv_pm = true,
+};
+
+static const struct iwl_dvm_bt_params iwl2030_bt_params = {
+	/* Due to bluetooth, we transmit 2.4 GHz probes only on antenna A */
+	.advanced_bt_coexist = true,
+	.agg_time_limit = BT_AGG_THRESHOLD_DEF,
+	.bt_init_traffic_load = IWL_BT_COEX_TRAFFIC_LOAD_NONE,
+	.bt_prio_boost = IWLAGN_BT_PRIO_BOOST_DEFAULT32,
+	.bt_sco_disable = true,
+	.bt_session_2 = true,
 };
 
 struct iwl_dvm_cfg iwl_dvm_2030_cfg = {
 	.set_hw_params = iwl2000_hw_set_hw_params,
 	.nic_config = iwl2000_nic_config,
 	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.hd_v2 = true,
+	.bt_params = &iwl2030_bt_params,
+	.need_temp_offset_calib = true,
+	.temp_offset_v2 = true,
+	.adv_pm = true,
 };
 
 /*
@@ -424,12 +467,19 @@ struct iwl_dvm_cfg iwl_dvm_5000_cfg = {
 	.set_hw_params = iwl5000_hw_set_hw_params,
 	.set_channel_switch = iwl5000_hw_channel_switch,
 	.temperature = iwlagn_temperature,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_LONG_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.no_idle_support = true,
 };
 
 struct iwl_dvm_cfg iwl_dvm_5150_cfg = {
 	.set_hw_params = iwl5150_hw_set_hw_params,
 	.set_channel_switch = iwl5000_hw_channel_switch,
 	.temperature = iwl5150_temperature,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_LONG_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.no_idle_support = true,
+	.no_xtal_calib = true,
 };
 
 
@@ -589,6 +639,42 @@ struct iwl_dvm_cfg iwl_dvm_6000_cfg = {
 	.set_channel_switch = iwl6000_hw_channel_switch,
 	.nic_config = iwl6000_nic_config,
 	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+};
+
+const struct iwl_dvm_cfg iwl_dvm_6005_cfg = {
+	.set_hw_params = iwl6000_hw_set_hw_params,
+	.set_channel_switch = iwl6000_hw_channel_switch,
+	.nic_config = iwl6000_nic_config,
+	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.need_temp_offset_calib = true,
+};
+
+struct iwl_dvm_cfg iwl_dvm_6050_cfg = {
+	.set_hw_params = iwl6000_hw_set_hw_params,
+	.set_channel_switch = iwl6000_hw_channel_switch,
+	.nic_config = iwl6000_nic_config,
+	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1500,
+};
+
+static const struct iwl_dvm_bt_params iwl6000_bt_params = {
+	/* Due to bluetooth, we transmit 2.4 GHz probes only on antenna A */
+	.advanced_bt_coexist = true,
+	.agg_time_limit = BT_AGG_THRESHOLD_DEF,
+	.bt_init_traffic_load = IWL_BT_COEX_TRAFFIC_LOAD_NONE,
+	.bt_prio_boost = IWLAGN_BT_PRIO_BOOST_DEFAULT,
+	.bt_sco_disable = true,
 };
 
 struct iwl_dvm_cfg iwl_dvm_6030_cfg = {
@@ -596,4 +682,11 @@ struct iwl_dvm_cfg iwl_dvm_6030_cfg = {
 	.set_channel_switch = iwl6000_hw_channel_switch,
 	.nic_config = iwl6000_nic_config,
 	.temperature = iwlagn_temperature,
+	.adv_thermal_throttle = true,
+	.support_ct_kill_exit = true,
+	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
+	.chain_noise_scale = 1000,
+	.bt_params = &iwl6000_bt_params,
+	.need_temp_offset_calib = true,
+	.adv_pm = true,
 };

drivers/net/wireless/iwlwifi/dvm/lib.c

@@ -254,23 +254,23 @@ void iwlagn_send_advance_bt_config(struct iwl_priv *priv)
 	BUILD_BUG_ON(sizeof(iwlagn_def_3w_lookup) !=
 			sizeof(basic.bt3_lookup_table));
 
-	if (priv->cfg->bt_params) {
+	if (priv->lib->bt_params) {
 		/*
 		 * newer generation of devices (2000 series and newer)
 		 * use the version 2 of the bt command
 		 * we need to make sure sending the host command
 		 * with correct data structure to avoid uCode assert
 		 */
-		if (priv->cfg->bt_params->bt_session_2) {
+		if (priv->lib->bt_params->bt_session_2) {
 			bt_cmd_v2.prio_boost = cpu_to_le32(
-				priv->cfg->bt_params->bt_prio_boost);
+				priv->lib->bt_params->bt_prio_boost);
 			bt_cmd_v2.tx_prio_boost = 0;
 			bt_cmd_v2.rx_prio_boost = 0;
 		} else {
 			/* older version only has 8 bits */
-			WARN_ON(priv->cfg->bt_params->bt_prio_boost & ~0xFF);
+			WARN_ON(priv->lib->bt_params->bt_prio_boost & ~0xFF);
 			bt_cmd_v1.prio_boost =
-				priv->cfg->bt_params->bt_prio_boost;
+				priv->lib->bt_params->bt_prio_boost;
 			bt_cmd_v1.tx_prio_boost = 0;
 			bt_cmd_v1.rx_prio_boost = 0;
 		}
@@ -330,7 +330,7 @@ void iwlagn_send_advance_bt_config(struct iwl_priv *priv)
 		       priv->bt_full_concurrent ?
 		       "full concurrency" : "3-wire");
 
-	if (priv->cfg->bt_params->bt_session_2) {
+	if (priv->lib->bt_params->bt_session_2) {
 		memcpy(&bt_cmd_v2.basic, &basic,
 			sizeof(basic));
 		ret = iwl_dvm_send_cmd_pdu(priv, REPLY_BT_CONFIG,
@@ -758,8 +758,8 @@ static bool is_single_rx_stream(struct iwl_priv *priv)
  */
 static int iwl_get_active_rx_chain_count(struct iwl_priv *priv)
 {
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist &&
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist &&
 	    (priv->bt_full_concurrent ||
 	     priv->bt_traffic_load >= IWL_BT_COEX_TRAFFIC_LOAD_HIGH)) {
 		/*
@@ -830,8 +830,8 @@ void iwlagn_set_rxon_chain(struct iwl_priv *priv, struct iwl_rxon_context *ctx)
 	else
 		active_chains = priv->nvm_data->valid_rx_ant;
 
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist &&
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist &&
 	    (priv->bt_full_concurrent ||
 	     priv->bt_traffic_load >= IWL_BT_COEX_TRAFFIC_LOAD_HIGH)) {
 		/*

drivers/net/wireless/iwlwifi/dvm/mac80211.c

@@ -1284,8 +1284,8 @@ static void iwlagn_mac_rssi_callback(struct ieee80211_hw *hw,
 	IWL_DEBUG_MAC80211(priv, "enter\n");
 	mutex_lock(&priv->mutex);
 
-	if (priv->cfg->bt_params &&
-			priv->cfg->bt_params->advanced_bt_coexist) {
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		if (rssi_event == RSSI_EVENT_LOW)
 			priv->bt_enable_pspoll = true;
 		else if (rssi_event == RSSI_EVENT_HIGH)
@@ -1395,7 +1395,7 @@ static int iwl_setup_interface(struct iwl_priv *priv,
 		return err;
 	}
 
-	if (priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist &&
+	if (priv->lib->bt_params && priv->lib->bt_params->advanced_bt_coexist &&
 	    vif->type == NL80211_IFTYPE_ADHOC) {
 		/*
 		 * pretend to have high BT traffic as long as we

drivers/net/wireless/iwlwifi/dvm/main.c

@@ -615,7 +615,7 @@ static void iwl_rf_kill_ct_config(struct iwl_priv *priv)
 
 	priv->thermal_throttle.ct_kill_toggle = false;
 
-	if (priv->cfg->base_params->support_ct_kill_exit) {
+	if (priv->lib->support_ct_kill_exit) {
 		adv_cmd.critical_temperature_enter =
 			cpu_to_le32(priv->hw_params.ct_kill_threshold);
 		adv_cmd.critical_temperature_exit =
@@ -732,10 +732,10 @@ int iwl_alive_start(struct iwl_priv *priv)
 	}
 
 	/* download priority table before any calibration request */
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		/* Configure Bluetooth device coexistence support */
-		if (priv->cfg->bt_params->bt_sco_disable)
+		if (priv->lib->bt_params->bt_sco_disable)
 			priv->bt_enable_pspoll = false;
 		else
 			priv->bt_enable_pspoll = true;
@@ -873,9 +873,9 @@ void iwl_down(struct iwl_priv *priv)
 	priv->bt_status = 0;
 	priv->cur_rssi_ctx = NULL;
 	priv->bt_is_sco = 0;
-	if (priv->cfg->bt_params)
+	if (priv->lib->bt_params)
 		priv->bt_traffic_load =
-			 priv->cfg->bt_params->bt_init_traffic_load;
+			 priv->lib->bt_params->bt_init_traffic_load;
 	else
 		priv->bt_traffic_load = 0;
 	priv->bt_full_concurrent = false;
@@ -1058,7 +1058,7 @@ static void iwl_setup_deferred_work(struct iwl_priv *priv)
 
 	iwl_setup_scan_deferred_work(priv);
 
-	if (priv->cfg->bt_params)
+	if (priv->lib->bt_params)
 		iwlagn_bt_setup_deferred_work(priv);
 
 	init_timer(&priv->statistics_periodic);
@@ -1072,7 +1072,7 @@ static void iwl_setup_deferred_work(struct iwl_priv *priv)
 
 void iwl_cancel_deferred_work(struct iwl_priv *priv)
 {
-	if (priv->cfg->bt_params)
+	if (priv->lib->bt_params)
 		iwlagn_bt_cancel_deferred_work(priv);
 
 	cancel_work_sync(&priv->run_time_calib_work);
@@ -1098,8 +1098,7 @@ static int iwl_init_drv(struct iwl_priv *priv)
 
 	priv->band = IEEE80211_BAND_2GHZ;
 
-	priv->plcp_delta_threshold =
-		priv->cfg->base_params->plcp_delta_threshold;
+	priv->plcp_delta_threshold = priv->lib->plcp_delta_threshold;
 
 	priv->iw_mode = NL80211_IFTYPE_STATION;
 	priv->current_ht_config.smps = IEEE80211_SMPS_STATIC;
@@ -1116,8 +1115,8 @@ static int iwl_init_drv(struct iwl_priv *priv)
 	iwl_init_scan_params(priv);
 
 	/* init bt coex */
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		priv->kill_ack_mask = IWLAGN_BT_KILL_ACK_MASK_DEFAULT;
 		priv->kill_cts_mask = IWLAGN_BT_KILL_CTS_MASK_DEFAULT;
 		priv->bt_valid = IWLAGN_BT_ALL_VALID_MSK;
@@ -1267,9 +1266,11 @@ static struct iwl_op_mode *iwl_op_mode_dvm_start(struct iwl_trans *trans,
 		priv->lib = &iwl_dvm_1000_cfg;
 		break;
 	case IWL_DEVICE_FAMILY_2000:
-	case IWL_DEVICE_FAMILY_105:
 		priv->lib = &iwl_dvm_2000_cfg;
 		break;
+	case IWL_DEVICE_FAMILY_105:
+		priv->lib = &iwl_dvm_105_cfg;
+		break;
 	case IWL_DEVICE_FAMILY_2030:
 	case IWL_DEVICE_FAMILY_135:
 		priv->lib = &iwl_dvm_2030_cfg;
@@ -1281,11 +1282,15 @@ static struct iwl_op_mode *iwl_op_mode_dvm_start(struct iwl_trans *trans,
 		priv->lib = &iwl_dvm_5150_cfg;
 		break;
 	case IWL_DEVICE_FAMILY_6000:
-	case IWL_DEVICE_FAMILY_6005:
 	case IWL_DEVICE_FAMILY_6000i:
+		priv->lib = &iwl_dvm_6000_cfg;
+		break;
+	case IWL_DEVICE_FAMILY_6005:
+		priv->lib = &iwl_dvm_6005_cfg;
+		break;
 	case IWL_DEVICE_FAMILY_6050:
 	case IWL_DEVICE_FAMILY_6150:
-		priv->lib = &iwl_dvm_6000_cfg;
+		priv->lib = &iwl_dvm_6050_cfg;
 		break;
 	case IWL_DEVICE_FAMILY_6030:
 		priv->lib = &iwl_dvm_6030_cfg;

drivers/net/wireless/iwlwifi/dvm/power.c

@@ -163,7 +163,7 @@ static void iwl_static_sleep_cmd(struct iwl_priv *priv,
 	u8 skip;
 	u32 slp_itrvl;
 
-	if (priv->cfg->adv_pm) {
+	if (priv->lib->adv_pm) {
 		table = apm_range_2;
 		if (period <= IWL_DTIM_RANGE_1_MAX)
 			table = apm_range_1;
@@ -217,7 +217,7 @@ static void iwl_static_sleep_cmd(struct iwl_priv *priv,
 		cmd->flags &= ~IWL_POWER_SHADOW_REG_ENA;
 
 	if (iwl_advanced_bt_coexist(priv)) {
-		if (!priv->cfg->bt_params->bt_sco_disable)
+		if (!priv->lib->bt_params->bt_sco_disable)
 			cmd->flags |= IWL_POWER_BT_SCO_ENA;
 		else
 			cmd->flags &= ~IWL_POWER_BT_SCO_ENA;
@@ -293,7 +293,7 @@ static void iwl_power_build_cmd(struct iwl_priv *priv,
 
 	if (priv->wowlan)
 		iwl_static_sleep_cmd(priv, cmd, IWL_POWER_INDEX_5, dtimper);
-	else if (!priv->cfg->base_params->no_idle_support &&
+	else if (!priv->lib->no_idle_support &&
 		 priv->hw->conf.flags & IEEE80211_CONF_IDLE)
 		iwl_static_sleep_cmd(priv, cmd, IWL_POWER_INDEX_5, 20);
 	else if (iwl_tt_is_low_power_state(priv)) {

drivers/net/wireless/iwlwifi/dvm/rs.c

@@ -1088,7 +1088,7 @@ done:
 	    (priv->tm_fixed_rate != lq_sta->dbg_fixed_rate))
 		rs_program_fix_rate(priv, lq_sta);
 #endif
-	if (priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist)
+	if (priv->lib->bt_params && priv->lib->bt_params->advanced_bt_coexist)
 		rs_bt_update_lq(priv, ctx, lq_sta);
 }
 
@@ -3064,11 +3064,11 @@ static void rs_fill_link_cmd(struct iwl_priv *priv,
 	 * overwrite if needed, pass aggregation time limit
 	 * to uCode in uSec
 	 */
-	if (priv && priv->cfg->bt_params &&
-	    priv->cfg->bt_params->agg_time_limit &&
+	if (priv && priv->lib->bt_params &&
+	    priv->lib->bt_params->agg_time_limit &&
 	    priv->bt_traffic_load >= IWL_BT_COEX_TRAFFIC_LOAD_HIGH)
 		lq_cmd->agg_params.agg_time_limit =
-			cpu_to_le16(priv->cfg->bt_params->agg_time_limit);
+			cpu_to_le16(priv->lib->bt_params->agg_time_limit);
 }
 
 static void *rs_alloc(struct ieee80211_hw *hw, struct dentry *debugfsdir)

drivers/net/wireless/iwlwifi/dvm/rx.c

@@ -1102,7 +1102,7 @@ void iwl_setup_rx_handlers(struct iwl_priv *priv)
 	iwl_notification_wait_init(&priv->notif_wait);
 
 	/* Set up BT Rx handlers */
-	if (priv->cfg->bt_params)
+	if (priv->lib->bt_params)
 		iwlagn_bt_rx_handler_setup(priv);
 }
 

drivers/net/wireless/iwlwifi/dvm/scan.c

@@ -801,8 +801,8 @@ static int iwlagn_request_scan(struct iwl_priv *priv, struct ieee80211_vif *vif)
 		 * Internal scans are passive, so we can indiscriminately set
 		 * the BT ignore flag on 2.4 GHz since it applies to TX only.
 		 */
-		if (priv->cfg->bt_params &&
-		    priv->cfg->bt_params->advanced_bt_coexist)
+		if (priv->lib->bt_params &&
+		    priv->lib->bt_params->advanced_bt_coexist)
 			scan->tx_cmd.tx_flags |= TX_CMD_FLG_IGNORE_BT;
 		break;
 	case IEEE80211_BAND_5GHZ:
@@ -844,8 +844,8 @@ static int iwlagn_request_scan(struct iwl_priv *priv, struct ieee80211_vif *vif)
 	band = priv->scan_band;
 
 	if (band == IEEE80211_BAND_2GHZ &&
-	    priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	    priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		/* transmit 2.4 GHz probes only on first antenna */
 		scan_tx_antennas = first_antenna(scan_tx_antennas);
 	}
@@ -873,8 +873,8 @@ static int iwlagn_request_scan(struct iwl_priv *priv, struct ieee80211_vif *vif)
 
 		rx_ant = first_antenna(active_chains);
 	}
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist &&
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist &&
 	    priv->bt_full_concurrent) {
 		/* operated as 1x1 in full concurrency mode */
 		rx_ant = first_antenna(rx_ant);

drivers/net/wireless/iwlwifi/dvm/tt.c

@@ -627,7 +627,7 @@ void iwl_tt_initialize(struct iwl_priv *priv)
 	INIT_WORK(&priv->ct_enter, iwl_bg_ct_enter);
 	INIT_WORK(&priv->ct_exit, iwl_bg_ct_exit);
 
-	if (priv->cfg->base_params->adv_thermal_throttle) {
+	if (priv->lib->adv_thermal_throttle) {
 		IWL_DEBUG_TEMP(priv, "Advanced Thermal Throttling\n");
 		tt->restriction = kcalloc(IWL_TI_STATE_MAX,
 					  sizeof(struct iwl_tt_restriction),

drivers/net/wireless/iwlwifi/dvm/tx.c

@@ -83,8 +83,8 @@ static void iwlagn_tx_cmd_build_basic(struct iwl_priv *priv,
 	else if (ieee80211_is_back_req(fc))
 		tx_flags |= TX_CMD_FLG_ACK_MSK | TX_CMD_FLG_IMM_BA_RSP_MASK;
 	else if (info->band == IEEE80211_BAND_2GHZ &&
-		 priv->cfg->bt_params &&
-		 priv->cfg->bt_params->advanced_bt_coexist &&
+		 priv->lib->bt_params &&
+		 priv->lib->bt_params->advanced_bt_coexist &&
 		 (ieee80211_is_auth(fc) || ieee80211_is_assoc_req(fc) ||
 		 ieee80211_is_reassoc_req(fc) ||
 		 skb->protocol == cpu_to_be16(ETH_P_PAE)))
@@ -202,8 +202,8 @@ static void iwlagn_tx_cmd_build_rate(struct iwl_priv *priv,
 		rate_flags |= RATE_MCS_CCK_MSK;
 
 	/* Set up antennas */
-	 if (priv->cfg->bt_params &&
-	     priv->cfg->bt_params->advanced_bt_coexist &&
+	 if (priv->lib->bt_params &&
+	     priv->lib->bt_params->advanced_bt_coexist &&
 	     priv->bt_full_concurrent) {
 		/* operated as 1x1 in full concurrency mode */
 		priv->mgmt_tx_ant = iwl_toggle_tx_ant(priv, priv->mgmt_tx_ant,
@@ -986,8 +986,8 @@ static void iwl_rx_reply_tx_agg(struct iwl_priv *priv,
 	 * notification again.
 	 */
 	if (tx_resp->bt_kill_count && tx_resp->frame_count == 1 &&
-	    priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	    priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		IWL_DEBUG_COEX(priv, "receive reply tx w/ bt_kill\n");
 	}
 

drivers/net/wireless/iwlwifi/dvm/ucode.c

@@ -132,8 +132,8 @@ int iwl_init_alive_start(struct iwl_priv *priv)
 {
 	int ret;
 
-	if (priv->cfg->bt_params &&
-	    priv->cfg->bt_params->advanced_bt_coexist) {
+	if (priv->lib->bt_params &&
+	    priv->lib->bt_params->advanced_bt_coexist) {
 		/*
 		 * Tell uCode we are ready to perform calibration
 		 * need to perform this before any calibration
@@ -155,8 +155,8 @@ int iwl_init_alive_start(struct iwl_priv *priv)
 	 * temperature offset calibration is only needed for runtime ucode,
 	 * so prepare the value now.
 	 */
-	if (priv->cfg->need_temp_offset_calib) {
-		if (priv->cfg->temp_offset_v2)
+	if (priv->lib->need_temp_offset_calib) {
+		if (priv->lib->temp_offset_v2)
 			return iwl_set_temperature_offset_calib_v2(priv);
 		else
 			return iwl_set_temperature_offset_calib(priv);
@@ -277,7 +277,7 @@ static int iwl_alive_notify(struct iwl_priv *priv)
 	if (ret)
 		return ret;
 
-	if (!priv->cfg->no_xtal_calib) {
+	if (!priv->lib->no_xtal_calib) {
 		ret = iwl_set_Xtal_calib(priv);
 		if (ret)
 			return ret;

drivers/net/wireless/iwlwifi/iwl-1000.c

@@ -60,9 +60,6 @@ static const struct iwl_base_params iwl1000_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_1000,
 	.shadow_ram_support = false,
 	.led_compensation = 51,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_EXT_LONG_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_WATCHDOG_DISABLED,
 	.max_event_log_size = 128,
 };

drivers/net/wireless/iwlwifi/iwl-2000.c

@@ -72,14 +72,9 @@ static const struct iwl_base_params iwl2000_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_2x00,
 	.shadow_ram_support = true,
 	.led_compensation = 51,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_DEF_WD_TIMEOUT,
 	.max_event_log_size = 512,
 	.shadow_reg_enable = false, /* TODO: fix bugs using this feature */
-	.hd_v2 = true,
 };
 
 
@@ -90,14 +85,9 @@ static const struct iwl_base_params iwl2030_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_2x00,
 	.shadow_ram_support = true,
 	.led_compensation = 57,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_LONG_WD_TIMEOUT,
 	.max_event_log_size = 512,
 	.shadow_reg_enable = false, /* TODO: fix bugs using this feature */
-	.hd_v2 = true,
 };
 
 static const struct iwl_ht_params iwl2000_ht_params = {
@@ -106,16 +96,6 @@ static const struct iwl_ht_params iwl2000_ht_params = {
 	.ht40_bands = BIT(IEEE80211_BAND_2GHZ),
 };
 
-static const struct iwl_bt_params iwl2030_bt_params = {
-	/* Due to bluetooth, we transmit 2.4 GHz probes only on antenna A */
-	.advanced_bt_coexist = true,
-	.agg_time_limit = BT_AGG_THRESHOLD_DEF,
-	.bt_init_traffic_load = IWL_BT_COEX_TRAFFIC_LOAD_NONE,
-	.bt_prio_boost = IWLAGN_BT_PRIO_BOOST_DEFAULT32,
-	.bt_sco_disable = true,
-	.bt_session_2 = true,
-};
-
 static const struct iwl_eeprom_params iwl20x0_eeprom_params = {
 	.regulatory_bands = {
 		EEPROM_REG_BAND_1_CHANNELS,
@@ -137,12 +117,10 @@ static const struct iwl_eeprom_params iwl20x0_eeprom_params = {
 	.device_family = IWL_DEVICE_FAMILY_2000,		\
 	.max_inst_size = IWL60_RTC_INST_SIZE,			\
 	.max_data_size = IWL60_RTC_DATA_SIZE,			\
-	.nvm_ver = EEPROM_2000_EEPROM_VERSION,		\
-	.nvm_calib_ver = EEPROM_2000_TX_POWER_VERSION,	\
+	.nvm_ver = EEPROM_2000_EEPROM_VERSION,			\
+	.nvm_calib_ver = EEPROM_2000_TX_POWER_VERSION,		\
 	.base_params = &iwl2000_base_params,			\
 	.eeprom_params = &iwl20x0_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.temp_offset_v2 = true,					\
 	.led_mode = IWL_LED_RF_STATE
 
 const struct iwl_cfg iwl2000_2bgn_cfg = {
@@ -168,12 +146,8 @@ const struct iwl_cfg iwl2000_2bgn_d_cfg = {
 	.nvm_ver = EEPROM_2000_EEPROM_VERSION,		\
 	.nvm_calib_ver = EEPROM_2000_TX_POWER_VERSION,	\
 	.base_params = &iwl2030_base_params,			\
-	.bt_params = &iwl2030_bt_params,			\
 	.eeprom_params = &iwl20x0_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.temp_offset_v2 = true,					\
-	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true
+	.led_mode = IWL_LED_RF_STATE
 
 const struct iwl_cfg iwl2030_2bgn_cfg = {
 	.name = "Intel(R) Centrino(R) Wireless-N 2230 BGN",
@@ -193,10 +167,7 @@ const struct iwl_cfg iwl2030_2bgn_cfg = {
 	.nvm_calib_ver = EEPROM_2000_TX_POWER_VERSION,	\
 	.base_params = &iwl2000_base_params,			\
 	.eeprom_params = &iwl20x0_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.temp_offset_v2 = true,					\
 	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true,						\
 	.rx_with_siso_diversity = true
 
 const struct iwl_cfg iwl105_bgn_cfg = {
@@ -222,12 +193,8 @@ const struct iwl_cfg iwl105_bgn_d_cfg = {
 	.nvm_ver = EEPROM_2000_EEPROM_VERSION,		\
 	.nvm_calib_ver = EEPROM_2000_TX_POWER_VERSION,	\
 	.base_params = &iwl2030_base_params,			\
-	.bt_params = &iwl2030_bt_params,			\
 	.eeprom_params = &iwl20x0_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.temp_offset_v2 = true,					\
 	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true,						\
 	.rx_with_siso_diversity = true
 
 const struct iwl_cfg iwl135_bgn_cfg = {

drivers/net/wireless/iwlwifi/iwl-5000.c

@@ -59,11 +59,8 @@ static const struct iwl_base_params iwl5000_base_params = {
 	.num_of_queues = IWLAGN_NUM_QUEUES,
 	.pll_cfg_val = CSR50_ANA_PLL_CFG_VAL,
 	.led_compensation = 51,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_LONG_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_WATCHDOG_DISABLED,
 	.max_event_log_size = 512,
-	.no_idle_support = true,
 };
 
 static const struct iwl_ht_params iwl5000_ht_params = {
@@ -159,7 +156,6 @@ const struct iwl_cfg iwl5350_agn_cfg = {
 	.nvm_calib_ver = EEPROM_5050_TX_POWER_VERSION,	\
 	.base_params = &iwl5000_base_params,			\
 	.eeprom_params = &iwl5000_eeprom_params,		\
-	.no_xtal_calib = true,					\
 	.led_mode = IWL_LED_BLINK,				\
 	.internal_wimax_coex = true
 

drivers/net/wireless/iwlwifi/iwl-6000.c

@@ -82,10 +82,6 @@ static const struct iwl_base_params iwl6000_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_6x00,
 	.shadow_ram_support = true,
 	.led_compensation = 51,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_DEF_WD_TIMEOUT,
 	.max_event_log_size = 512,
 	.shadow_reg_enable = false, /* TODO: fix bugs using this feature */
@@ -98,10 +94,6 @@ static const struct iwl_base_params iwl6050_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_6x50,
 	.shadow_ram_support = true,
 	.led_compensation = 51,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1500,
 	.wd_timeout = IWL_DEF_WD_TIMEOUT,
 	.max_event_log_size = 1024,
 	.shadow_reg_enable = false, /* TODO: fix bugs using this feature */
@@ -114,10 +106,6 @@ static const struct iwl_base_params iwl6000_g2_base_params = {
 	.max_ll_items = OTP_MAX_LL_ITEMS_6x00,
 	.shadow_ram_support = true,
 	.led_compensation = 57,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_LONG_WD_TIMEOUT,
 	.max_event_log_size = 512,
 	.shadow_reg_enable = false, /* TODO: fix bugs using this feature */
@@ -129,15 +117,6 @@ static const struct iwl_ht_params iwl6000_ht_params = {
 	.ht40_bands = BIT(IEEE80211_BAND_2GHZ) | BIT(IEEE80211_BAND_5GHZ),
 };
 
-static const struct iwl_bt_params iwl6000_bt_params = {
-	/* Due to bluetooth, we transmit 2.4 GHz probes only on antenna A */
-	.advanced_bt_coexist = true,
-	.agg_time_limit = BT_AGG_THRESHOLD_DEF,
-	.bt_init_traffic_load = IWL_BT_COEX_TRAFFIC_LOAD_NONE,
-	.bt_prio_boost = IWLAGN_BT_PRIO_BOOST_DEFAULT,
-	.bt_sco_disable = true,
-};
-
 static const struct iwl_eeprom_params iwl6000_eeprom_params = {
 	.regulatory_bands = {
 		EEPROM_REG_BAND_1_CHANNELS,
@@ -163,7 +142,6 @@ static const struct iwl_eeprom_params iwl6000_eeprom_params = {
 	.nvm_calib_ver = EEPROM_6005_TX_POWER_VERSION,	\
 	.base_params = &iwl6000_g2_base_params,			\
 	.eeprom_params = &iwl6000_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
 	.led_mode = IWL_LED_RF_STATE
 
 const struct iwl_cfg iwl6005_2agn_cfg = {
@@ -217,11 +195,8 @@ const struct iwl_cfg iwl6005_2agn_mow2_cfg = {
 	.nvm_ver = EEPROM_6030_EEPROM_VERSION,		\
 	.nvm_calib_ver = EEPROM_6030_TX_POWER_VERSION,	\
 	.base_params = &iwl6000_g2_base_params,			\
-	.bt_params = &iwl6000_bt_params,			\
 	.eeprom_params = &iwl6000_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true						\
+	.led_mode = IWL_LED_RF_STATE
 
 const struct iwl_cfg iwl6030_2agn_cfg = {
 	.name = "Intel(R) Centrino(R) Advanced-N 6230 AGN",
@@ -256,11 +231,8 @@ const struct iwl_cfg iwl6030_2bg_cfg = {
 	.nvm_ver = EEPROM_6030_EEPROM_VERSION,		\
 	.nvm_calib_ver = EEPROM_6030_TX_POWER_VERSION,	\
 	.base_params = &iwl6000_g2_base_params,			\
-	.bt_params = &iwl6000_bt_params,			\
 	.eeprom_params = &iwl6000_eeprom_params,		\
-	.need_temp_offset_calib = true,				\
-	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true
+	.led_mode = IWL_LED_RF_STATE
 
 const struct iwl_cfg iwl6035_2agn_cfg = {
 	.name = "Intel(R) Centrino(R) Advanced-N 6235 AGN",

drivers/net/wireless/iwlwifi/iwl-7000.c

@@ -96,10 +96,6 @@ static const struct iwl_base_params iwl7000_base_params = {
 	.pll_cfg_val = 0,
 	.shadow_ram_support = true,
 	.led_compensation = 57,
-	.adv_thermal_throttle = true,
-	.support_ct_kill_exit = true,
-	.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
-	.chain_noise_scale = 1000,
 	.wd_timeout = IWL_LONG_WD_TIMEOUT,
 	.max_event_log_size = 512,
 	.shadow_reg_enable = true,
@@ -118,10 +114,7 @@ static const struct iwl_ht_params iwl7000_ht_params = {
 	.max_inst_size = IWL60_RTC_INST_SIZE,			\
 	.max_data_size = IWL60_RTC_DATA_SIZE,			\
 	.base_params = &iwl7000_base_params,			\
-	/* TODO: .bt_params? */					\
-	.need_temp_offset_calib = true,				\
-	.led_mode = IWL_LED_RF_STATE,				\
-	.adv_pm = true						\
+	.led_mode = IWL_LED_RF_STATE
 
 
 const struct iwl_cfg iwl7260_2ac_cfg = {

drivers/net/wireless/iwlwifi/iwl-config.h

@@ -136,17 +136,9 @@ enum iwl_led_mode {
  * @led_compensation: compensate on the led on/off time per HW according
  *	to the deviation to achieve the desired led frequency.
  *	The detail algorithm is described in iwl-led.c
- * @chain_noise_num_beacons: number of beacons used to compute chain noise
- * @adv_thermal_throttle: support advance thermal throttle
- * @support_ct_kill_exit: support ct kill exit condition
- * @plcp_delta_threshold: plcp error rate threshold used to trigger
- *	radio tuning when there is a high receiving plcp error rate
- * @chain_noise_scale: default chain noise scale used for gain computation
  * @wd_timeout: TX queues watchdog timeout
  * @max_event_log_size: size of event log buffer size for ucode event logging
  * @shadow_reg_enable: HW shadow register support
- * @hd_v2: v2 of enhanced sensitivity value, used for 2000 series and up
- * @no_idle_support: do not support idle mode
  */
 struct iwl_base_params {
 	int eeprom_size;
@@ -157,31 +149,9 @@ struct iwl_base_params {
 	const u16 max_ll_items;
 	const bool shadow_ram_support;
 	u16 led_compensation;
-	bool adv_thermal_throttle;
-	bool support_ct_kill_exit;
-	u8 plcp_delta_threshold;
-	s32 chain_noise_scale;
 	unsigned int wd_timeout;
 	u32 max_event_log_size;
 	const bool shadow_reg_enable;
-	const bool hd_v2;
-	const bool no_idle_support;
-};
-
-/*
- * @advanced_bt_coexist: support advanced bt coexist
- * @bt_init_traffic_load: specify initial bt traffic load
- * @bt_prio_boost: default bt priority boost value
- * @agg_time_limit: maximum number of uSec in aggregation
- * @bt_sco_disable: uCode should not response to BT in SCO/ESCO mode
- */
-struct iwl_bt_params {
-	bool advanced_bt_coexist;
-	u8 bt_init_traffic_load;
-	u32 bt_prio_boost;
-	u16 agg_time_limit;
-	bool bt_sco_disable;
-	bool bt_session_2;
 };
 
 /*
@@ -231,16 +201,10 @@ struct iwl_eeprom_params {
  * @nvm_calib_ver: NVM calibration version
  * @lib: pointer to the lib ops
  * @base_params: pointer to basic parameters
- * @ht_params: point to ht patameters
- * @bt_params: pointer to bt parameters
- * @need_temp_offset_calib: need to perform temperature offset calibration
- * @no_xtal_calib: some devices do not need crystal calibration data,
- *	don't send it to those
+ * @ht_params: point to ht parameters
  * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off)
- * @adv_pm: advance power management
  * @rx_with_siso_diversity: 1x1 device with rx antenna diversity
  * @internal_wimax_coex: internal wifi/wimax combo device
- * @temp_offset_v2: support v2 of temperature offset calibration
  *
  * We enable the driver to be backward compatible wrt. hardware features.
  * API differences in uCode shouldn't be handled here but through TLVs
@@ -264,15 +228,10 @@ struct iwl_cfg {
 	const struct iwl_base_params *base_params;
 	/* params likely to change within a device family */
 	const struct iwl_ht_params *ht_params;
-	const struct iwl_bt_params *bt_params;
 	const struct iwl_eeprom_params *eeprom_params;
-	const bool need_temp_offset_calib; /* if used set to true */
-	const bool no_xtal_calib;
 	enum iwl_led_mode led_mode;
-	const bool adv_pm;
 	const bool rx_with_siso_diversity;
 	const bool internal_wimax_coex;
-	const bool temp_offset_v2;
 };
 
 /*