Merge branch spi-next from git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

drivers/spi/Kconfig

@@ -297,9 +297,20 @@ config SPI_PPC4xx
 	help
 	  This selects a driver for the PPC4xx SPI Controller.
 
+config SPI_PXA2XX_PXADMA
+	bool "PXA2xx SSP legacy PXA DMA API support"
+	depends on SPI_PXA2XX && ARCH_PXA
+	help
+	  Enable PXA private legacy DMA API support. Note that this is
+	  deprecated in favor of generic DMA engine API.
+
+config SPI_PXA2XX_DMA
+	def_bool y
+	depends on SPI_PXA2XX && !SPI_PXA2XX_PXADMA
+
 config SPI_PXA2XX
 	tristate "PXA2xx SSP SPI master"
-	depends on ARCH_PXA || PCI
+	depends on ARCH_PXA || PCI || ACPI
 	select PXA_SSP if ARCH_PXA
 	help
 	  This enables using a PXA2xx or Sodaville SSP port as a SPI master

drivers/spi/Makefile

@@ -47,7 +47,10 @@ obj-$(CONFIG_SPI_OMAP24XX)		+= spi-omap2-mcspi.o
 obj-$(CONFIG_SPI_ORION)			+= spi-orion.o
 obj-$(CONFIG_SPI_PL022)			+= spi-pl022.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
-obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx.o
+spi-pxa2xx-platform-objs		:= spi-pxa2xx.o
+spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_PXADMA)	+= spi-pxa2xx-pxadma.o
+spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_DMA)	+= spi-pxa2xx-dma.o
+obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx-platform.o
 obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
 obj-$(CONFIG_SPI_RSPI)			+= spi-rspi.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi-s3c24xx-hw.o

drivers/spi/spi-pxa2xx-dma.c

@@ -0,0 +1,392 @@
+/*
+ * PXA2xx SPI DMA engine support.
+ *
+ * Copyright (C) 2013, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/pxa2xx_ssp.h>
+#include <linux/scatterlist.h>
+#include <linux/sizes.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
+
+#include "spi-pxa2xx.h"
+
+static int pxa2xx_spi_map_dma_buffer(struct driver_data *drv_data,
+				     enum dma_data_direction dir)
+{
+	int i, nents, len = drv_data->len;
+	struct scatterlist *sg;
+	struct device *dmadev;
+	struct sg_table *sgt;
+	void *buf, *pbuf;
+
+	/*
+	 * Some DMA controllers have problems transferring buffers that are
+	 * not multiple of 4 bytes. So we truncate the transfer so that it
+	 * is suitable for such controllers, and handle the trailing bytes
+	 * manually after the DMA completes.
+	 *
+	 * REVISIT: It would be better if this information could be
+	 * retrieved directly from the DMA device in a similar way than
+	 * ->copy_align etc. is done.
+	 */
+	len = ALIGN(drv_data->len, 4);
+
+	if (dir == DMA_TO_DEVICE) {
+		dmadev = drv_data->tx_chan->device->dev;
+		sgt = &drv_data->tx_sgt;
+		buf = drv_data->tx;
+		drv_data->tx_map_len = len;
+	} else {
+		dmadev = drv_data->rx_chan->device->dev;
+		sgt = &drv_data->rx_sgt;
+		buf = drv_data->rx;
+		drv_data->rx_map_len = len;
+	}
+
+	nents = DIV_ROUND_UP(len, SZ_2K);
+	if (nents != sgt->nents) {
+		int ret;
+
+		sg_free_table(sgt);
+		ret = sg_alloc_table(sgt, nents, GFP_KERNEL);
+		if (ret)
+			return ret;
+	}
+
+	pbuf = buf;
+	for_each_sg(sgt->sgl, sg, sgt->nents, i) {
+		size_t bytes = min_t(size_t, len, SZ_2K);
+
+		if (buf)
+			sg_set_buf(sg, pbuf, bytes);
+		else
+			sg_set_buf(sg, drv_data->dummy, bytes);
+
+		pbuf += bytes;
+		len -= bytes;
+	}
+
+	nents = dma_map_sg(dmadev, sgt->sgl, sgt->nents, dir);
+	if (!nents)
+		return -ENOMEM;
+
+	return nents;
+}
+
+static void pxa2xx_spi_unmap_dma_buffer(struct driver_data *drv_data,
+					enum dma_data_direction dir)
+{
+	struct device *dmadev;
+	struct sg_table *sgt;
+
+	if (dir == DMA_TO_DEVICE) {
+		dmadev = drv_data->tx_chan->device->dev;
+		sgt = &drv_data->tx_sgt;
+	} else {
+		dmadev = drv_data->rx_chan->device->dev;
+		sgt = &drv_data->rx_sgt;
+	}
+
+	dma_unmap_sg(dmadev, sgt->sgl, sgt->nents, dir);
+}
+
+static void pxa2xx_spi_unmap_dma_buffers(struct driver_data *drv_data)
+{
+	if (!drv_data->dma_mapped)
+		return;
+
+	pxa2xx_spi_unmap_dma_buffer(drv_data, DMA_FROM_DEVICE);
+	pxa2xx_spi_unmap_dma_buffer(drv_data, DMA_TO_DEVICE);
+
+	drv_data->dma_mapped = 0;
+}
+
+static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data,
+					     bool error)
+{
+	struct spi_message *msg = drv_data->cur_msg;
+
+	/*
+	 * It is possible that one CPU is handling ROR interrupt and other
+	 * just gets DMA completion. Calling pump_transfers() twice for the
+	 * same transfer leads to problems thus we prevent concurrent calls
+	 * by using ->dma_running.
+	 */
+	if (atomic_dec_and_test(&drv_data->dma_running)) {
+		void __iomem *reg = drv_data->ioaddr;
+
+		/*
+		 * If the other CPU is still handling the ROR interrupt we
+		 * might not know about the error yet. So we re-check the
+		 * ROR bit here before we clear the status register.
+		 */
+		if (!error) {
+			u32 status = read_SSSR(reg) & drv_data->mask_sr;
+			error = status & SSSR_ROR;
+		}
+
+		/* Clear status & disable interrupts */
+		write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
+		write_SSSR_CS(drv_data, drv_data->clear_sr);
+		if (!pxa25x_ssp_comp(drv_data))
+			write_SSTO(0, reg);
+
+		if (!error) {
+			pxa2xx_spi_unmap_dma_buffers(drv_data);
+
+			/* Handle the last bytes of unaligned transfer */
+			drv_data->tx += drv_data->tx_map_len;
+			drv_data->write(drv_data);
+
+			drv_data->rx += drv_data->rx_map_len;
+			drv_data->read(drv_data);
+
+			msg->actual_length += drv_data->len;
+			msg->state = pxa2xx_spi_next_transfer(drv_data);
+		} else {
+			/* In case we got an error we disable the SSP now */
+			write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
+
+			msg->state = ERROR_STATE;
+		}
+
+		tasklet_schedule(&drv_data->pump_transfers);
+	}
+}
+
+static void pxa2xx_spi_dma_callback(void *data)
+{
+	pxa2xx_spi_dma_transfer_complete(data, false);
+}
+
+static struct dma_async_tx_descriptor *
+pxa2xx_spi_dma_prepare_one(struct driver_data *drv_data,
+			   enum dma_transfer_direction dir)
+{
+	struct pxa2xx_spi_master *pdata = drv_data->master_info;
+	struct chip_data *chip = drv_data->cur_chip;
+	enum dma_slave_buswidth width;
+	struct dma_slave_config cfg;
+	struct dma_chan *chan;
+	struct sg_table *sgt;
+	int nents, ret;
+
+	switch (drv_data->n_bytes) {
+	case 1:
+		width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+		break;
+	case 2:
+		width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+		break;
+	default:
+		width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+		break;
+	}
+
+	memset(&cfg, 0, sizeof(cfg));
+	cfg.direction = dir;
+
+	if (dir == DMA_MEM_TO_DEV) {
+		cfg.dst_addr = drv_data->ssdr_physical;
+		cfg.dst_addr_width = width;
+		cfg.dst_maxburst = chip->dma_burst_size;
+		cfg.slave_id = pdata->tx_slave_id;
+
+		sgt = &drv_data->tx_sgt;
+		nents = drv_data->tx_nents;
+		chan = drv_data->tx_chan;
+	} else {
+		cfg.src_addr = drv_data->ssdr_physical;
+		cfg.src_addr_width = width;
+		cfg.src_maxburst = chip->dma_burst_size;
+		cfg.slave_id = pdata->rx_slave_id;
+
+		sgt = &drv_data->rx_sgt;
+		nents = drv_data->rx_nents;
+		chan = drv_data->rx_chan;
+	}
+
+	ret = dmaengine_slave_config(chan, &cfg);
+	if (ret) {
+		dev_warn(&drv_data->pdev->dev, "DMA slave config failed\n");
+		return NULL;
+	}
+
+	return dmaengine_prep_slave_sg(chan, sgt->sgl, nents, dir,
+				       DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+}
+
+static bool pxa2xx_spi_dma_filter(struct dma_chan *chan, void *param)
+{
+	const struct pxa2xx_spi_master *pdata = param;
+
+	return chan->chan_id == pdata->tx_chan_id ||
+	       chan->chan_id == pdata->rx_chan_id;
+}
+
+bool pxa2xx_spi_dma_is_possible(size_t len)
+{
+	return len <= MAX_DMA_LEN;
+}
+
+int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data)
+{
+	const struct chip_data *chip = drv_data->cur_chip;
+	int ret;
+
+	if (!chip->enable_dma)
+		return 0;
+
+	/* Don't bother with DMA if we can't do even a single burst */
+	if (drv_data->len < chip->dma_burst_size)
+		return 0;
+
+	ret = pxa2xx_spi_map_dma_buffer(drv_data, DMA_TO_DEVICE);
+	if (ret <= 0) {
+		dev_warn(&drv_data->pdev->dev, "failed to DMA map TX\n");
+		return 0;
+	}
+
+	drv_data->tx_nents = ret;
+
+	ret = pxa2xx_spi_map_dma_buffer(drv_data, DMA_FROM_DEVICE);
+	if (ret <= 0) {
+		pxa2xx_spi_unmap_dma_buffer(drv_data, DMA_TO_DEVICE);
+		dev_warn(&drv_data->pdev->dev, "failed to DMA map RX\n");
+		return 0;
+	}
+
+	drv_data->rx_nents = ret;
+	return 1;
+}
+
+irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data)
+{
+	u32 status;
+
+	status = read_SSSR(drv_data->ioaddr) & drv_data->mask_sr;
+	if (status & SSSR_ROR) {
+		dev_err(&drv_data->pdev->dev, "FIFO overrun\n");
+
+		dmaengine_terminate_all(drv_data->rx_chan);
+		dmaengine_terminate_all(drv_data->tx_chan);
+
+		pxa2xx_spi_dma_transfer_complete(drv_data, true);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+int pxa2xx_spi_dma_prepare(struct driver_data *drv_data, u32 dma_burst)
+{
+	struct dma_async_tx_descriptor *tx_desc, *rx_desc;
+
+	tx_desc = pxa2xx_spi_dma_prepare_one(drv_data, DMA_MEM_TO_DEV);
+	if (!tx_desc) {
+		dev_err(&drv_data->pdev->dev,
+			"failed to get DMA TX descriptor\n");
+		return -EBUSY;
+	}
+
+	rx_desc = pxa2xx_spi_dma_prepare_one(drv_data, DMA_DEV_TO_MEM);
+	if (!rx_desc) {
+		dev_err(&drv_data->pdev->dev,
+			"failed to get DMA RX descriptor\n");
+		return -EBUSY;
+	}
+
+	/* We are ready when RX completes */
+	rx_desc->callback = pxa2xx_spi_dma_callback;
+	rx_desc->callback_param = drv_data;
+
+	dmaengine_submit(rx_desc);
+	dmaengine_submit(tx_desc);
+	return 0;
+}
+
+void pxa2xx_spi_dma_start(struct driver_data *drv_data)
+{
+	dma_async_issue_pending(drv_data->rx_chan);
+	dma_async_issue_pending(drv_data->tx_chan);
+
+	atomic_set(&drv_data->dma_running, 1);
+}
+
+int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
+{
+	struct pxa2xx_spi_master *pdata = drv_data->master_info;
+	dma_cap_mask_t mask;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+
+	drv_data->dummy = devm_kzalloc(&drv_data->pdev->dev, SZ_2K, GFP_KERNEL);
+	if (!drv_data->dummy)
+		return -ENOMEM;
+
+	drv_data->tx_chan = dma_request_channel(mask, pxa2xx_spi_dma_filter,
+						pdata);
+	if (!drv_data->tx_chan)
+		return -ENODEV;
+
+	drv_data->rx_chan = dma_request_channel(mask, pxa2xx_spi_dma_filter,
+						pdata);
+	if (!drv_data->rx_chan) {
+		dma_release_channel(drv_data->tx_chan);
+		drv_data->tx_chan = NULL;
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+void pxa2xx_spi_dma_release(struct driver_data *drv_data)
+{
+	if (drv_data->rx_chan) {
+		dmaengine_terminate_all(drv_data->rx_chan);
+		dma_release_channel(drv_data->rx_chan);
+		sg_free_table(&drv_data->rx_sgt);
+		drv_data->rx_chan = NULL;
+	}
+	if (drv_data->tx_chan) {
+		dmaengine_terminate_all(drv_data->tx_chan);
+		dma_release_channel(drv_data->tx_chan);
+		sg_free_table(&drv_data->tx_sgt);
+		drv_data->tx_chan = NULL;
+	}
+}
+
+void pxa2xx_spi_dma_resume(struct driver_data *drv_data)
+{
+}
+
+int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
+					   struct spi_device *spi,
+					   u8 bits_per_word, u32 *burst_code,
+					   u32 *threshold)
+{
+	struct pxa2xx_spi_chip *chip_info = spi->controller_data;
+
+	/*
+	 * If the DMA burst size is given in chip_info we use that,
+	 * otherwise we use the default. Also we use the default FIFO
+	 * thresholds for now.
+	 */
+	*burst_code = chip_info ? chip_info->dma_burst_size : 16;
+	*threshold = SSCR1_RxTresh(RX_THRESH_DFLT)
+		   | SSCR1_TxTresh(TX_THRESH_DFLT);
+
+	return 0;
+}

drivers/spi/spi-pxa2xx-pxadma.c

@@ -0,0 +1,490 @@
+/*
+ * PXA2xx SPI private DMA support.
+ *
+ * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/pxa2xx_ssp.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
+
+#include "spi-pxa2xx.h"
+
+#define DMA_INT_MASK		(DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
+#define RESET_DMA_CHANNEL	(DCSR_NODESC | DMA_INT_MASK)
+
+bool pxa2xx_spi_dma_is_possible(size_t len)
+{
+	/* Try to map dma buffer and do a dma transfer if successful, but
+	 * only if the length is non-zero and less than MAX_DMA_LEN.
+	 *
+	 * Zero-length non-descriptor DMA is illegal on PXA2xx; force use
+	 * of PIO instead.  Care is needed above because the transfer may
+	 * have have been passed with buffers that are already dma mapped.
+	 * A zero-length transfer in PIO mode will not try to write/read
+	 * to/from the buffers
+	 *
+	 * REVISIT large transfers are exactly where we most want to be
+	 * using DMA.  If this happens much, split those transfers into
+	 * multiple DMA segments rather than forcing PIO.
+	 */
+	return len > 0 && len <= MAX_DMA_LEN;
+}
+
+int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data)
+{
+	struct spi_message *msg = drv_data->cur_msg;
+	struct device *dev = &msg->spi->dev;
+
+	if (!drv_data->cur_chip->enable_dma)
+		return 0;
+
+	if (msg->is_dma_mapped)
+		return  drv_data->rx_dma && drv_data->tx_dma;
+
+	if (!IS_DMA_ALIGNED(drv_data->rx) || !IS_DMA_ALIGNED(drv_data->tx))
+		return 0;
+
+	/* Modify setup if rx buffer is null */
+	if (drv_data->rx == NULL) {
+		*drv_data->null_dma_buf = 0;
+		drv_data->rx = drv_data->null_dma_buf;
+		drv_data->rx_map_len = 4;
+	} else
+		drv_data->rx_map_len = drv_data->len;
+
+
+	/* Modify setup if tx buffer is null */
+	if (drv_data->tx == NULL) {
+		*drv_data->null_dma_buf = 0;
+		drv_data->tx = drv_data->null_dma_buf;
+		drv_data->tx_map_len = 4;
+	} else
+		drv_data->tx_map_len = drv_data->len;
+
+	/* Stream map the tx buffer. Always do DMA_TO_DEVICE first
+	 * so we flush the cache *before* invalidating it, in case
+	 * the tx and rx buffers overlap.
+	 */
+	drv_data->tx_dma = dma_map_single(dev, drv_data->tx,
+					drv_data->tx_map_len, DMA_TO_DEVICE);
+	if (dma_mapping_error(dev, drv_data->tx_dma))
+		return 0;
+
+	/* Stream map the rx buffer */
+	drv_data->rx_dma = dma_map_single(dev, drv_data->rx,
+					drv_data->rx_map_len, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, drv_data->rx_dma)) {
+		dma_unmap_single(dev, drv_data->tx_dma,
+					drv_data->tx_map_len, DMA_TO_DEVICE);
+		return 0;
+	}
+
+	return 1;
+}
+
+static void pxa2xx_spi_unmap_dma_buffers(struct driver_data *drv_data)
+{
+	struct device *dev;
+
+	if (!drv_data->dma_mapped)
+		return;
+
+	if (!drv_data->cur_msg->is_dma_mapped) {
+		dev = &drv_data->cur_msg->spi->dev;
+		dma_unmap_single(dev, drv_data->rx_dma,
+					drv_data->rx_map_len, DMA_FROM_DEVICE);
+		dma_unmap_single(dev, drv_data->tx_dma,
+					drv_data->tx_map_len, DMA_TO_DEVICE);
+	}
+
+	drv_data->dma_mapped = 0;
+}
+
+static int wait_ssp_rx_stall(void const __iomem *ioaddr)
+{
+	unsigned long limit = loops_per_jiffy << 1;
+
+	while ((read_SSSR(ioaddr) & SSSR_BSY) && --limit)
+		cpu_relax();
+
+	return limit;
+}
+
+static int wait_dma_channel_stop(int channel)
+{
+	unsigned long limit = loops_per_jiffy << 1;
+
+	while (!(DCSR(channel) & DCSR_STOPSTATE) && --limit)
+		cpu_relax();
+
+	return limit;
+}
+
+static void pxa2xx_spi_dma_error_stop(struct driver_data *drv_data,
+				      const char *msg)
+{
+	void __iomem *reg = drv_data->ioaddr;
+
+	/* Stop and reset */
+	DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
+	DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
+	write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
+	if (!pxa25x_ssp_comp(drv_data))
+		write_SSTO(0, reg);
+	pxa2xx_spi_flush(drv_data);
+	write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
+
+	pxa2xx_spi_unmap_dma_buffers(drv_data);
+
+	dev_err(&drv_data->pdev->dev, "%s\n", msg);
+
+	drv_data->cur_msg->state = ERROR_STATE;
+	tasklet_schedule(&drv_data->pump_transfers);
+}
+
+static void pxa2xx_spi_dma_transfer_complete(struct driver_data *drv_data)
+{
+	void __iomem *reg = drv_data->ioaddr;
+	struct spi_message *msg = drv_data->cur_msg;
+
+	/* Clear and disable interrupts on SSP and DMA channels*/
+	write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
+	write_SSSR_CS(drv_data, drv_data->clear_sr);
+	DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
+	DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
+
+	if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
+		dev_err(&drv_data->pdev->dev,
+			"dma_handler: dma rx channel stop failed\n");
+
+	if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
+		dev_err(&drv_data->pdev->dev,
+			"dma_transfer: ssp rx stall failed\n");
+
+	pxa2xx_spi_unmap_dma_buffers(drv_data);
+
+	/* update the buffer pointer for the amount completed in dma */
+	drv_data->rx += drv_data->len -
+			(DCMD(drv_data->rx_channel) & DCMD_LENGTH);
+
+	/* read trailing data from fifo, it does not matter how many
+	 * bytes are in the fifo just read until buffer is full
+	 * or fifo is empty, which ever occurs first */
+	drv_data->read(drv_data);
+
+	/* return count of what was actually read */
+	msg->actual_length += drv_data->len -
+				(drv_data->rx_end - drv_data->rx);
+
+	/* Transfer delays and chip select release are
+	 * handled in pump_transfers or giveback
+	 */
+
+	/* Move to next transfer */
+	msg->state = pxa2xx_spi_next_transfer(drv_data);
+
+	/* Schedule transfer tasklet */
+	tasklet_schedule(&drv_data->pump_transfers);
+}
+
+void pxa2xx_spi_dma_handler(int channel, void *data)
+{
+	struct driver_data *drv_data = data;
+	u32 irq_status = DCSR(channel) & DMA_INT_MASK;
+
+	if (irq_status & DCSR_BUSERR) {
+
+		if (channel == drv_data->tx_channel)
+			pxa2xx_spi_dma_error_stop(drv_data,
+				"dma_handler: bad bus address on tx channel");
+		else
+			pxa2xx_spi_dma_error_stop(drv_data,
+				"dma_handler: bad bus address on rx channel");
+		return;
+	}
+
+	/* PXA255x_SSP has no timeout interrupt, wait for tailing bytes */
+	if ((channel == drv_data->tx_channel)
+		&& (irq_status & DCSR_ENDINTR)
+		&& (drv_data->ssp_type == PXA25x_SSP)) {
+
+		/* Wait for rx to stall */
+		if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
+			dev_err(&drv_data->pdev->dev,
+				"dma_handler: ssp rx stall failed\n");
+
+		/* finish this transfer, start the next */
+		pxa2xx_spi_dma_transfer_complete(drv_data);
+	}
+}
+
+irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data)
+{
+	u32 irq_status;
+	void __iomem *reg = drv_data->ioaddr;
+
+	irq_status = read_SSSR(reg) & drv_data->mask_sr;
+	if (irq_status & SSSR_ROR) {
+		pxa2xx_spi_dma_error_stop(drv_data,
+					  "dma_transfer: fifo overrun");
+		return IRQ_HANDLED;
+	}
+
+	/* Check for false positive timeout */
+	if ((irq_status & SSSR_TINT)
+		&& (DCSR(drv_data->tx_channel) & DCSR_RUN)) {
+		write_SSSR(SSSR_TINT, reg);
+		return IRQ_HANDLED;
+	}
+
+	if (irq_status & SSSR_TINT || drv_data->rx == drv_data->rx_end) {
+
+		/* Clear and disable timeout interrupt, do the rest in
+		 * dma_transfer_complete */
+		if (!pxa25x_ssp_comp(drv_data))
+			write_SSTO(0, reg);
+
+		/* finish this transfer, start the next */
+		pxa2xx_spi_dma_transfer_complete(drv_data);
+
+		return IRQ_HANDLED;
+	}
+
+	/* Opps problem detected */
+	return IRQ_NONE;
+}
+
+int pxa2xx_spi_dma_prepare(struct driver_data *drv_data, u32 dma_burst)
+{
+	u32 dma_width;
+
+	switch (drv_data->n_bytes) {
+	case 1:
+		dma_width = DCMD_WIDTH1;
+		break;
+	case 2:
+		dma_width = DCMD_WIDTH2;
+		break;
+	default:
+		dma_width = DCMD_WIDTH4;
+		break;
+	}
+
+	/* Setup rx DMA Channel */
+	DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
+	DSADR(drv_data->rx_channel) = drv_data->ssdr_physical;
+	DTADR(drv_data->rx_channel) = drv_data->rx_dma;
+	if (drv_data->rx == drv_data->null_dma_buf)
+		/* No target address increment */
+		DCMD(drv_data->rx_channel) = DCMD_FLOWSRC
+						| dma_width
+						| dma_burst
+						| drv_data->len;
+	else
+		DCMD(drv_data->rx_channel) = DCMD_INCTRGADDR
+						| DCMD_FLOWSRC
+						| dma_width
+						| dma_burst
+						| drv_data->len;
+
+	/* Setup tx DMA Channel */
+	DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
+	DSADR(drv_data->tx_channel) = drv_data->tx_dma;
+	DTADR(drv_data->tx_channel) = drv_data->ssdr_physical;
+	if (drv_data->tx == drv_data->null_dma_buf)
+		/* No source address increment */
+		DCMD(drv_data->tx_channel) = DCMD_FLOWTRG
+						| dma_width
+						| dma_burst
+						| drv_data->len;
+	else
+		DCMD(drv_data->tx_channel) = DCMD_INCSRCADDR
+						| DCMD_FLOWTRG
+						| dma_width
+						| dma_burst
+						| drv_data->len;
+
+	/* Enable dma end irqs on SSP to detect end of transfer */
+	if (drv_data->ssp_type == PXA25x_SSP)
+		DCMD(drv_data->tx_channel) |= DCMD_ENDIRQEN;
+
+	return 0;
+}
+
+void pxa2xx_spi_dma_start(struct driver_data *drv_data)
+{
+	DCSR(drv_data->rx_channel) |= DCSR_RUN;
+	DCSR(drv_data->tx_channel) |= DCSR_RUN;
+}
+
+int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
+{
+	struct device *dev = &drv_data->pdev->dev;
+	struct ssp_device *ssp = drv_data->ssp;
+
+	/* Get two DMA channels	(rx and tx) */
+	drv_data->rx_channel = pxa_request_dma("pxa2xx_spi_ssp_rx",
+						DMA_PRIO_HIGH,
+						pxa2xx_spi_dma_handler,
+						drv_data);
+	if (drv_data->rx_channel < 0) {
+		dev_err(dev, "problem (%d) requesting rx channel\n",
+			drv_data->rx_channel);
+		return -ENODEV;
+	}
+	drv_data->tx_channel = pxa_request_dma("pxa2xx_spi_ssp_tx",
+						DMA_PRIO_MEDIUM,
+						pxa2xx_spi_dma_handler,
+						drv_data);
+	if (drv_data->tx_channel < 0) {
+		dev_err(dev, "problem (%d) requesting tx channel\n",
+			drv_data->tx_channel);
+		pxa_free_dma(drv_data->rx_channel);
+		return -ENODEV;
+	}
+
+	DRCMR(ssp->drcmr_rx) = DRCMR_MAPVLD | drv_data->rx_channel;
+	DRCMR(ssp->drcmr_tx) = DRCMR_MAPVLD | drv_data->tx_channel;
+
+	return 0;
+}
+
+void pxa2xx_spi_dma_release(struct driver_data *drv_data)
+{
+	struct ssp_device *ssp = drv_data->ssp;
+
+	DRCMR(ssp->drcmr_rx) = 0;
+	DRCMR(ssp->drcmr_tx) = 0;
+
+	if (drv_data->tx_channel != 0)
+		pxa_free_dma(drv_data->tx_channel);
+	if (drv_data->rx_channel != 0)
+		pxa_free_dma(drv_data->rx_channel);
+}
+
+void pxa2xx_spi_dma_resume(struct driver_data *drv_data)
+{
+	if (drv_data->rx_channel != -1)
+		DRCMR(drv_data->ssp->drcmr_rx) =
+			DRCMR_MAPVLD | drv_data->rx_channel;
+	if (drv_data->tx_channel != -1)
+		DRCMR(drv_data->ssp->drcmr_tx) =
+			DRCMR_MAPVLD | drv_data->tx_channel;
+}
+
+int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
+					   struct spi_device *spi,
+					   u8 bits_per_word, u32 *burst_code,
+					   u32 *threshold)
+{
+	struct pxa2xx_spi_chip *chip_info =
+			(struct pxa2xx_spi_chip *)spi->controller_data;
+	int bytes_per_word;
+	int burst_bytes;
+	int thresh_words;
+	int req_burst_size;
+	int retval = 0;
+
+	/* Set the threshold (in registers) to equal the same amount of data
+	 * as represented by burst size (in bytes).  The computation below
+	 * is (burst_size rounded up to nearest 8 byte, word or long word)
+	 * divided by (bytes/register); the tx threshold is the inverse of
+	 * the rx, so that there will always be enough data in the rx fifo
+	 * to satisfy a burst, and there will always be enough space in the
+	 * tx fifo to accept a burst (a tx burst will overwrite the fifo if
+	 * there is not enough space), there must always remain enough empty
+	 * space in the rx fifo for any data loaded to the tx fifo.
+	 * Whenever burst_size (in bytes) equals bits/word, the fifo threshold
+	 * will be 8, or half the fifo;
+	 * The threshold can only be set to 2, 4 or 8, but not 16, because
+	 * to burst 16 to the tx fifo, the fifo would have to be empty;
+	 * however, the minimum fifo trigger level is 1, and the tx will
+	 * request service when the fifo is at this level, with only 15 spaces.
+	 */
+
+	/* find bytes/word */
+	if (bits_per_word <= 8)
+		bytes_per_word = 1;
+	else if (bits_per_word <= 16)
+		bytes_per_word = 2;
+	else
+		bytes_per_word = 4;
+
+	/* use struct pxa2xx_spi_chip->dma_burst_size if available */
+	if (chip_info)
+		req_burst_size = chip_info->dma_burst_size;
+	else {
+		switch (chip->dma_burst_size) {
+		default:
+			/* if the default burst size is not set,
+			 * do it now */
+			chip->dma_burst_size = DCMD_BURST8;
+		case DCMD_BURST8:
+			req_burst_size = 8;
+			break;
+		case DCMD_BURST16:
+			req_burst_size = 16;
+			break;
+		case DCMD_BURST32:
+			req_burst_size = 32;
+			break;
+		}
+	}
+	if (req_burst_size <= 8) {
+		*burst_code = DCMD_BURST8;
+		burst_bytes = 8;
+	} else if (req_burst_size <= 16) {
+		if (bytes_per_word == 1) {
+			/* don't burst more than 1/2 the fifo */
+			*burst_code = DCMD_BURST8;
+			burst_bytes = 8;
+			retval = 1;
+		} else {
+			*burst_code = DCMD_BURST16;
+			burst_bytes = 16;
+		}
+	} else {
+		if (bytes_per_word == 1) {
+			/* don't burst more than 1/2 the fifo */
+			*burst_code = DCMD_BURST8;
+			burst_bytes = 8;
+			retval = 1;
+		} else if (bytes_per_word == 2) {
+			/* don't burst more than 1/2 the fifo */
+			*burst_code = DCMD_BURST16;
+			burst_bytes = 16;
+			retval = 1;
+		} else {
+			*burst_code = DCMD_BURST32;
+			burst_bytes = 32;
+		}
+	}
+
+	thresh_words = burst_bytes / bytes_per_word;
+
+	/* thresh_words will be between 2 and 8 */
+	*threshold = (SSCR1_RxTresh(thresh_words) & SSCR1_RFT)
+			| (SSCR1_TxTresh(16-thresh_words) & SSCR1_TFT);
+
+	return retval;
+}

drivers/spi/spi-pxa2xx.h

@@ -0,0 +1,221 @@
+/*
+ * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
+ * Copyright (C) 2013, Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef SPI_PXA2XX_H
+#define SPI_PXA2XX_H
+
+#include <linux/atomic.h>
+#include <linux/dmaengine.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/pxa2xx_ssp.h>
+#include <linux/scatterlist.h>
+#include <linux/sizes.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
+
+struct driver_data {
+	/* Driver model hookup */
+	struct platform_device *pdev;
+
+	/* SSP Info */
+	struct ssp_device *ssp;
+
+	/* SPI framework hookup */
+	enum pxa_ssp_type ssp_type;
+	struct spi_master *master;
+
+	/* PXA hookup */
+	struct pxa2xx_spi_master *master_info;
+
+	/* PXA private DMA setup stuff */
+	int rx_channel;
+	int tx_channel;
+	u32 *null_dma_buf;
+
+	/* SSP register addresses */
+	void __iomem *ioaddr;
+	u32 ssdr_physical;
+
+	/* SSP masks*/
+	u32 dma_cr1;
+	u32 int_cr1;
+	u32 clear_sr;
+	u32 mask_sr;
+
+	/* Maximun clock rate */
+	unsigned long max_clk_rate;
+
+	/* Message Transfer pump */
+	struct tasklet_struct pump_transfers;
+
+	/* DMA engine support */
+	struct dma_chan *rx_chan;
+	struct dma_chan *tx_chan;
+	struct sg_table rx_sgt;
+	struct sg_table tx_sgt;
+	int rx_nents;
+	int tx_nents;
+	void *dummy;
+	atomic_t dma_running;
+
+	/* Current message transfer state info */
+	struct spi_message *cur_msg;
+	struct spi_transfer *cur_transfer;
+	struct chip_data *cur_chip;
+	size_t len;
+	void *tx;
+	void *tx_end;
+	void *rx;
+	void *rx_end;
+	int dma_mapped;
+	dma_addr_t rx_dma;
+	dma_addr_t tx_dma;
+	size_t rx_map_len;
+	size_t tx_map_len;
+	u8 n_bytes;
+	int (*write)(struct driver_data *drv_data);
+	int (*read)(struct driver_data *drv_data);
+	irqreturn_t (*transfer_handler)(struct driver_data *drv_data);
+	void (*cs_control)(u32 command);
+
+	void __iomem *lpss_base;
+};
+
+struct chip_data {
+	u32 cr0;
+	u32 cr1;
+	u32 psp;
+	u32 timeout;
+	u8 n_bytes;
+	u32 dma_burst_size;
+	u32 threshold;
+	u32 dma_threshold;
+	u16 lpss_rx_threshold;
+	u16 lpss_tx_threshold;
+	u8 enable_dma;
+	u8 bits_per_word;
+	u32 speed_hz;
+	union {
+		int gpio_cs;
+		unsigned int frm;
+	};
+	int gpio_cs_inverted;
+	int (*write)(struct driver_data *drv_data);
+	int (*read)(struct driver_data *drv_data);
+	void (*cs_control)(u32 command);
+};
+
+#define DEFINE_SSP_REG(reg, off) \
+static inline u32 read_##reg(void const __iomem *p) \
+{ return __raw_readl(p + (off)); } \
+\
+static inline void write_##reg(u32 v, void __iomem *p) \
+{ __raw_writel(v, p + (off)); }
+
+DEFINE_SSP_REG(SSCR0, 0x00)
+DEFINE_SSP_REG(SSCR1, 0x04)
+DEFINE_SSP_REG(SSSR, 0x08)
+DEFINE_SSP_REG(SSITR, 0x0c)
+DEFINE_SSP_REG(SSDR, 0x10)
+DEFINE_SSP_REG(SSTO, 0x28)
+DEFINE_SSP_REG(SSPSP, 0x2c)
+DEFINE_SSP_REG(SSITF, SSITF)
+DEFINE_SSP_REG(SSIRF, SSIRF)
+
+#define START_STATE ((void *)0)
+#define RUNNING_STATE ((void *)1)
+#define DONE_STATE ((void *)2)
+#define ERROR_STATE ((void *)-1)
+
+#define IS_DMA_ALIGNED(x)	IS_ALIGNED((unsigned long)(x), DMA_ALIGNMENT)
+#define DMA_ALIGNMENT		8
+
+static inline int pxa25x_ssp_comp(struct driver_data *drv_data)
+{
+	if (drv_data->ssp_type == PXA25x_SSP)
+		return 1;
+	if (drv_data->ssp_type == CE4100_SSP)
+		return 1;
+	return 0;
+}
+
+static inline void write_SSSR_CS(struct driver_data *drv_data, u32 val)
+{
+	void __iomem *reg = drv_data->ioaddr;
+
+	if (drv_data->ssp_type == CE4100_SSP)
+		val |= read_SSSR(reg) & SSSR_ALT_FRM_MASK;
+
+	write_SSSR(val, reg);
+}
+
+extern int pxa2xx_spi_flush(struct driver_data *drv_data);
+extern void *pxa2xx_spi_next_transfer(struct driver_data *drv_data);
+
+/*
+ * Select the right DMA implementation.
+ */
+#if defined(CONFIG_SPI_PXA2XX_PXADMA)
+#define SPI_PXA2XX_USE_DMA	1
+#define MAX_DMA_LEN		8191
+#define DEFAULT_DMA_CR1		(SSCR1_TSRE | SSCR1_RSRE | SSCR1_TINTE)
+#elif defined(CONFIG_SPI_PXA2XX_DMA)
+#define SPI_PXA2XX_USE_DMA	1
+#define MAX_DMA_LEN		SZ_64K
+#define DEFAULT_DMA_CR1		(SSCR1_TSRE | SSCR1_RSRE | SSCR1_TRAIL)
+#else
+#undef SPI_PXA2XX_USE_DMA
+#define MAX_DMA_LEN		0
+#define DEFAULT_DMA_CR1		0
+#endif
+
+#ifdef SPI_PXA2XX_USE_DMA
+extern bool pxa2xx_spi_dma_is_possible(size_t len);
+extern int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data);
+extern irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data);
+extern int pxa2xx_spi_dma_prepare(struct driver_data *drv_data, u32 dma_burst);
+extern void pxa2xx_spi_dma_start(struct driver_data *drv_data);
+extern int pxa2xx_spi_dma_setup(struct driver_data *drv_data);
+extern void pxa2xx_spi_dma_release(struct driver_data *drv_data);
+extern void pxa2xx_spi_dma_resume(struct driver_data *drv_data);
+extern int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
+						  struct spi_device *spi,
+						  u8 bits_per_word,
+						  u32 *burst_code,
+						  u32 *threshold);
+#else
+static inline bool pxa2xx_spi_dma_is_possible(size_t len) { return false; }
+static inline int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data)
+{
+	return 0;
+}
+#define pxa2xx_spi_dma_transfer NULL
+static inline void pxa2xx_spi_dma_prepare(struct driver_data *drv_data,
+					  u32 dma_burst) {}
+static inline void pxa2xx_spi_dma_start(struct driver_data *drv_data) {}
+static inline int pxa2xx_spi_dma_setup(struct driver_data *drv_data)
+{
+	return 0;
+}
+static inline void pxa2xx_spi_dma_release(struct driver_data *drv_data) {}
+static inline void pxa2xx_spi_dma_resume(struct driver_data *drv_data) {}
+static inline int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
+							 struct spi_device *spi,
+							 u8 bits_per_word,
+							 u32 *burst_code,
+							 u32 *threshold)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* SPI_PXA2XX_H */

include/linux/pxa2xx_ssp.h

@@ -155,6 +155,14 @@
 #define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
 #define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
 
+/* LPSS SSP */
+#define SSITF			0x44		/* TX FIFO trigger level */
+#define SSITF_TxLoThresh(x)	(((x) - 1) << 8)
+#define SSITF_TxHiThresh(x)	((x) - 1)
+
+#define SSIRF			0x48		/* RX FIFO trigger level */
+#define SSIRF_RxThresh(x)	((x) - 1)
+
 enum pxa_ssp_type {
 	SSP_UNDEFINED = 0,
 	PXA25x_SSP,  /* pxa 210, 250, 255, 26x */
@@ -164,6 +172,7 @@ enum pxa_ssp_type {
 	PXA168_SSP,
 	PXA910_SSP,
 	CE4100_SSP,
+	LPSS_SSP,
 };
 
 struct ssp_device {

include/linux/spi/pxa2xx_spi.h

@@ -29,6 +29,12 @@ struct pxa2xx_spi_master {
 	u16 num_chipselect;
 	u8 enable_dma;
 
+	/* DMA engine specific config */
+	int rx_chan_id;
+	int tx_chan_id;
+	int rx_slave_id;
+	int tx_slave_id;
+
 	/* For non-PXA arches */
 	struct ssp_device ssp;
 };
@@ -38,6 +44,7 @@ struct pxa2xx_spi_master {
  */
 struct pxa2xx_spi_chip {
 	u8 tx_threshold;
+	u8 tx_hi_threshold;
 	u8 rx_threshold;
 	u8 dma_burst_size;
 	u32 timeout;
@@ -53,85 +60,5 @@ struct pxa2xx_spi_chip {
 
 extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
 
-#else
-/*
- * This is the implemtation for CE4100 on x86. ARM defines them in mach/ or
- * plat/ include path.
- * The CE4100 does not provide DMA support. This bits are here to let the driver
- * compile and will never be used. Maybe we get DMA support at a later point in
- * time.
- */
-
-#define DCSR(n)         (n)
-#define DSADR(n)        (n)
-#define DTADR(n)        (n)
-#define DCMD(n)         (n)
-#define DRCMR(n)        (n)
-
-#define DCSR_RUN	(1 << 31)	/* Run Bit */
-#define DCSR_NODESC	(1 << 30)	/* No-Descriptor Fetch */
-#define DCSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable */
-#define DCSR_REQPEND	(1 << 8)	/* Request Pending (read-only) */
-#define DCSR_STOPSTATE	(1 << 3)	/* Stop State (read-only) */
-#define DCSR_ENDINTR	(1 << 2)	/* End Interrupt */
-#define DCSR_STARTINTR	(1 << 1)	/* Start Interrupt */
-#define DCSR_BUSERR	(1 << 0)	/* Bus Error Interrupt */
-
-#define DCSR_EORIRQEN	(1 << 28)	/* End of Receive Interrupt Enable */
-#define DCSR_EORJMPEN	(1 << 27)	/* Jump to next descriptor on EOR */
-#define DCSR_EORSTOPEN	(1 << 26)	/* STOP on an EOR */
-#define DCSR_SETCMPST	(1 << 25)	/* Set Descriptor Compare Status */
-#define DCSR_CLRCMPST	(1 << 24)	/* Clear Descriptor Compare Status */
-#define DCSR_CMPST	(1 << 10)	/* The Descriptor Compare Status */
-#define DCSR_EORINTR	(1 << 9)	/* The end of Receive */
-
-#define DRCMR_MAPVLD	(1 << 7)	/* Map Valid */
-#define DRCMR_CHLNUM	0x1f		/* mask for Channel Number */
-
-#define DDADR_DESCADDR	0xfffffff0	/* Address of next descriptor */
-#define DDADR_STOP	(1 << 0)	/* Stop */
-
-#define DCMD_INCSRCADDR	(1 << 31)	/* Source Address Increment Setting. */
-#define DCMD_INCTRGADDR	(1 << 30)	/* Target Address Increment Setting. */
-#define DCMD_FLOWSRC	(1 << 29)	/* Flow Control by the source. */
-#define DCMD_FLOWTRG	(1 << 28)	/* Flow Control by the target. */
-#define DCMD_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
-#define DCMD_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
-#define DCMD_ENDIAN	(1 << 18)	/* Device Endian-ness. */
-#define DCMD_BURST8	(1 << 16)	/* 8 byte burst */
-#define DCMD_BURST16	(2 << 16)	/* 16 byte burst */
-#define DCMD_BURST32	(3 << 16)	/* 32 byte burst */
-#define DCMD_WIDTH1	(1 << 14)	/* 1 byte width */
-#define DCMD_WIDTH2	(2 << 14)	/* 2 byte width (HalfWord) */
-#define DCMD_WIDTH4	(3 << 14)	/* 4 byte width (Word) */
-#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
-
-/*
- * Descriptor structure for PXA's DMA engine
- * Note: this structure must always be aligned to a 16-byte boundary.
- */
-
-typedef enum {
-	DMA_PRIO_HIGH = 0,
-	DMA_PRIO_MEDIUM = 1,
-	DMA_PRIO_LOW = 2
-} pxa_dma_prio;
-
-/*
- * DMA registration
- */
-
-static inline int pxa_request_dma(char *name,
-		pxa_dma_prio prio,
-		void (*irq_handler)(int, void *),
-		void *data)
-{
-	return -ENODEV;
-}
-
-static inline void pxa_free_dma(int dma_ch)
-{
-}
-
 #endif
 #endif