[ARM] ohci-pxa27x: use ioremap() and offset for register access

This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-pxa/generic.c

@@ -88,11 +88,6 @@ static struct map_desc standard_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(0x48000000),
 		.length		= 0x00200000,
 		.type		= MT_DEVICE
-	}, {	/* USB host */
-		.virtual	=  0xf8000000,
-		.pfn		= __phys_to_pfn(0x4c000000),
-		.length		= 0x00100000,
-		.type		= MT_DEVICE
 	}, {	/* Camera */
 		.virtual	=  0xfa000000,
 		.pfn		= __phys_to_pfn(0x50000000),

drivers/usb/host/ohci-pxa27x.c

@@ -23,46 +23,43 @@
 #include <linux/signal.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
-
-#include <mach/hardware.h>
 #include <mach/ohci.h>
 
 /*
  * UHC: USB Host Controller (OHCI-like) register definitions
  */
-#define UHC_BASE_PHYS	(0x4C000000)
-#define UHCREV		__REG(0x4C000000) /* UHC HCI Spec Revision */
-#define UHCHCON		__REG(0x4C000004) /* UHC Host Control Register */
-#define UHCCOMS		__REG(0x4C000008) /* UHC Command Status Register */
-#define UHCINTS		__REG(0x4C00000C) /* UHC Interrupt Status Register */
-#define UHCINTE		__REG(0x4C000010) /* UHC Interrupt Enable */
-#define UHCINTD		__REG(0x4C000014) /* UHC Interrupt Disable */
-#define UHCHCCA		__REG(0x4C000018) /* UHC Host Controller Comm. Area */
-#define UHCPCED		__REG(0x4C00001C) /* UHC Period Current Endpt Descr */
-#define UHCCHED		__REG(0x4C000020) /* UHC Control Head Endpt Descr */
-#define UHCCCED		__REG(0x4C000024) /* UHC Control Current Endpt Descr */
-#define UHCBHED		__REG(0x4C000028) /* UHC Bulk Head Endpt Descr */
-#define UHCBCED		__REG(0x4C00002C) /* UHC Bulk Current Endpt Descr */
-#define UHCDHEAD	__REG(0x4C000030) /* UHC Done Head */
-#define UHCFMI		__REG(0x4C000034) /* UHC Frame Interval */
-#define UHCFMR		__REG(0x4C000038) /* UHC Frame Remaining */
-#define UHCFMN		__REG(0x4C00003C) /* UHC Frame Number */
-#define UHCPERS		__REG(0x4C000040) /* UHC Periodic Start */
-#define UHCLS		__REG(0x4C000044) /* UHC Low Speed Threshold */
-
-#define UHCRHDA		__REG(0x4C000048) /* UHC Root Hub Descriptor A */
+#define UHCREV		(0x0000) /* UHC HCI Spec Revision */
+#define UHCHCON		(0x0004) /* UHC Host Control Register */
+#define UHCCOMS		(0x0008) /* UHC Command Status Register */
+#define UHCINTS		(0x000C) /* UHC Interrupt Status Register */
+#define UHCINTE		(0x0010) /* UHC Interrupt Enable */
+#define UHCINTD		(0x0014) /* UHC Interrupt Disable */
+#define UHCHCCA		(0x0018) /* UHC Host Controller Comm. Area */
+#define UHCPCED		(0x001C) /* UHC Period Current Endpt Descr */
+#define UHCCHED		(0x0020) /* UHC Control Head Endpt Descr */
+#define UHCCCED		(0x0024) /* UHC Control Current Endpt Descr */
+#define UHCBHED		(0x0028) /* UHC Bulk Head Endpt Descr */
+#define UHCBCED		(0x002C) /* UHC Bulk Current Endpt Descr */
+#define UHCDHEAD	(0x0030) /* UHC Done Head */
+#define UHCFMI		(0x0034) /* UHC Frame Interval */
+#define UHCFMR		(0x0038) /* UHC Frame Remaining */
+#define UHCFMN		(0x003C) /* UHC Frame Number */
+#define UHCPERS		(0x0040) /* UHC Periodic Start */
+#define UHCLS		(0x0044) /* UHC Low Speed Threshold */
+
+#define UHCRHDA		(0x0048) /* UHC Root Hub Descriptor A */
 #define UHCRHDA_NOCP	(1 << 12)	/* No over current protection */
 #define UHCRHDA_OCPM	(1 << 11)	/* Over Current Protection Mode */
 #define UHCRHDA_POTPGT(x) \
 			(((x) & 0xff) << 24) /* Power On To Power Good Time */
 
-#define UHCRHDB		__REG(0x4C00004C) /* UHC Root Hub Descriptor B */
-#define UHCRHS		__REG(0x4C000050) /* UHC Root Hub Status */
-#define UHCRHPS1	__REG(0x4C000054) /* UHC Root Hub Port 1 Status */
-#define UHCRHPS2	__REG(0x4C000058) /* UHC Root Hub Port 2 Status */
-#define UHCRHPS3	__REG(0x4C00005C) /* UHC Root Hub Port 3 Status */
+#define UHCRHDB		(0x004C) /* UHC Root Hub Descriptor B */
+#define UHCRHS		(0x0050) /* UHC Root Hub Status */
+#define UHCRHPS1	(0x0054) /* UHC Root Hub Port 1 Status */
+#define UHCRHPS2	(0x0058) /* UHC Root Hub Port 2 Status */
+#define UHCRHPS3	(0x005C) /* UHC Root Hub Port 3 Status */
 
-#define UHCSTAT		__REG(0x4C000060) /* UHC Status Register */
+#define UHCSTAT		(0x0060) /* UHC Status Register */
 #define UHCSTAT_UPS3	(1 << 16)	/* USB Power Sense Port3 */
 #define UHCSTAT_SBMAI	(1 << 15)	/* System Bus Master Abort Interrupt*/
 #define UHCSTAT_SBTAI	(1 << 14)	/* System Bus Target Abort Interrupt*/
@@ -73,7 +70,7 @@
 #define UHCSTAT_HBA	(1 << 8)	/* HCI Buffer Active */
 #define UHCSTAT_RWUE	(1 << 7)	/* HCI Remote Wake Up Event */
 
-#define UHCHR           __REG(0x4C000064) /* UHC Reset Register */
+#define UHCHR           (0x0064) /* UHC Reset Register */
 #define UHCHR_SSEP3	(1 << 11)	/* Sleep Standby Enable for Port3 */
 #define UHCHR_SSEP2	(1 << 10)	/* Sleep Standby Enable for Port2 */
 #define UHCHR_SSEP1	(1 << 9)	/* Sleep Standby Enable for Port1 */
@@ -86,7 +83,7 @@
 #define UHCHR_FHR	(1 << 1)	/* Force Host Controller Reset */
 #define UHCHR_FSBIR	(1 << 0)	/* Force System Bus Iface Reset */
 
-#define UHCHIE          __REG(0x4C000068) /* UHC Interrupt Enable Register*/
+#define UHCHIE          (0x0068) /* UHC Interrupt Enable Register*/
 #define UHCHIE_UPS3IE	(1 << 14)	/* Power Sense Port3 IntEn */
 #define UHCHIE_UPRIE	(1 << 13)	/* Port Resume IntEn */
 #define UHCHIE_UPS2IE	(1 << 12)	/* Power Sense Port2 IntEn */
@@ -96,14 +93,20 @@
 #define UHCHIE_HBAIE	(1 << 8)	/* HCI Buffer Active IntEn */
 #define UHCHIE_RWIE	(1 << 7)	/* Remote Wake-up IntEn */
 
-#define UHCHIT          __REG(0x4C00006C) /* UHC Interrupt Test register */
-
+#define UHCHIT          (0x006C) /* UHC Interrupt Test register */
 
 #define PXA_UHC_MAX_PORTNUM    3
 
-#define UHCRHPS(x)              __REG2( 0x4C000050, (x)<<2 )
+struct pxa27x_ohci {
+	/* must be 1st member here for hcd_to_ohci() to work */
+	struct ohci_hcd ohci;
 
-static struct clk *usb_clk;
+	struct device	*dev;
+	struct clk	*clk;
+	void __iomem	*mmio_base;
+};
+
+#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)hcd_to_ohci(hcd)
 
 /*
   PMM_NPS_MODE -- PMM Non-power switching mode
@@ -115,30 +118,35 @@ static struct clk *usb_clk;
   PMM_PERPORT_MODE -- PMM per port switching mode
       Ports are powered individually.
  */
-static int pxa27x_ohci_select_pmm( int mode )
+static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
 {
-	switch ( mode ) {
+	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
+	uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB);
+
+	switch (mode) {
 	case PMM_NPS_MODE:
-		UHCRHDA |= RH_A_NPS;
+		uhcrhda |= RH_A_NPS;
 		break;
 	case PMM_GLOBAL_MODE:
-		UHCRHDA &= ~(RH_A_NPS & RH_A_PSM);
+		uhcrhda &= ~(RH_A_NPS & RH_A_PSM);
 		break;
 	case PMM_PERPORT_MODE:
-		UHCRHDA &= ~(RH_A_NPS);
-		UHCRHDA |= RH_A_PSM;
+		uhcrhda &= ~(RH_A_NPS);
+		uhcrhda |= RH_A_PSM;
 
 		/* Set port power control mask bits, only 3 ports. */
-		UHCRHDB |= (0x7<<17);
+		uhcrhdb |= (0x7<<17);
 		break;
 	default:
 		printk( KERN_ERR
 			"Invalid mode %d, set to non-power switch mode.\n",
 			mode );
 
-		UHCRHDA |= RH_A_NPS;
+		uhcrhda |= RH_A_NPS;
 	}
 
+	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
+	__raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB);
 	return 0;
 }
 
@@ -146,10 +154,11 @@ extern int usb_disabled(void);
 
 /*-------------------------------------------------------------------------*/
 
-static inline void pxa27x_setup_hc(struct pxaohci_platform_data *inf)
+static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
+				   struct pxaohci_platform_data *inf)
 {
-	uint32_t uhchr = UHCHR;
-	uint32_t uhcrhda = UHCRHDA;
+	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
+	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
 
 	if (inf->flags & ENABLE_PORT1)
 		uhchr &= ~UHCHR_SSEP1;
@@ -177,8 +186,17 @@ static inline void pxa27x_setup_hc(struct pxaohci_platform_data *inf)
 		uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
 	}
 
-	UHCHR = uhchr;
-	UHCRHDA = uhcrhda;
+	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
+	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
+}
+
+static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci)
+{
+	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
+
+	__raw_writel(uhchr | UHCHR_FHR, ohci->mmio_base + UHCHR);
+	udelay(11);
+	__raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR);
 }
 
 #ifdef CONFIG_CPU_PXA27x
@@ -187,24 +205,25 @@ extern void pxa27x_clear_otgph(void);
 #define pxa27x_clear_otgph()	do {} while (0)
 #endif
 
-static int pxa27x_start_hc(struct device *dev)
+static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 {
 	int retval = 0;
 	struct pxaohci_platform_data *inf;
+	uint32_t uhchr;
 
 	inf = dev->platform_data;
 
-	clk_enable(usb_clk);
+	clk_enable(ohci->clk);
 
-	UHCHR |= UHCHR_FHR;
-	udelay(11);
-	UHCHR &= ~UHCHR_FHR;
+	pxa27x_reset_hc(ohci);
 
-	UHCHR |= UHCHR_FSBIR;
-	while (UHCHR & UHCHR_FSBIR)
+	uhchr = __raw_readl(ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
+	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
+
+	while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
 		cpu_relax();
 
-	pxa27x_setup_hc(inf);
+	pxa27x_setup_hc(ohci, inf);
 
 	if (inf->init)
 		retval = inf->init(dev);
@@ -212,32 +231,33 @@ static int pxa27x_start_hc(struct device *dev)
 	if (retval < 0)
 		return retval;
 
-	UHCHR &= ~UHCHR_SSE;
-
-	UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);
+	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
+	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
+	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, ohci->mmio_base + UHCHIE);
 
 	/* Clear any OTG Pin Hold */
 	pxa27x_clear_otgph();
 	return 0;
 }
 
-static void pxa27x_stop_hc(struct device *dev)
+static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev)
 {
 	struct pxaohci_platform_data *inf;
+	uint32_t uhccoms;
 
 	inf = dev->platform_data;
 
 	if (inf->exit)
 		inf->exit(dev);
 
-	UHCHR |= UHCHR_FHR;
-	udelay(11);
-	UHCHR &= ~UHCHR_FHR;
+	pxa27x_reset_hc(ohci);
 
-	UHCCOMS |= 1;
+	/* Host Controller Reset */
+	uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) | 0x01;
+	__raw_writel(uhccoms, ohci->mmio_base + UHCCOMS);
 	udelay(10);
 
-	clk_disable(usb_clk);
+	clk_disable(ohci->clk);
 }
 
 
@@ -261,7 +281,9 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	int retval, irq;
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;
+	struct pxa27x_ohci *ohci;
 	struct resource *r;
+	struct clk *usb_clk;
 
 	inf = pdev->dev.platform_data;
 
@@ -305,13 +327,19 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 		goto err2;
 	}
 
-	if ((retval = pxa27x_start_hc(&pdev->dev)) < 0) {
+	/* initialize "struct pxa27x_ohci" */
+	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
+	ohci->dev = &pdev->dev;
+	ohci->clk = usb_clk;
+	ohci->mmio_base = (void __iomem *)hcd->regs;
+
+	if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) {
 		pr_debug("pxa27x_start_hc failed");
 		goto err3;
 	}
 
 	/* Select Power Management Mode */
-	pxa27x_ohci_select_pmm(inf->port_mode);
+	pxa27x_ohci_select_pmm(ohci, inf->port_mode);
 
 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;
@@ -322,7 +350,7 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
 	if (retval == 0)
 		return retval;
 
-	pxa27x_stop_hc(&pdev->dev);
+	pxa27x_stop_hc(ohci, &pdev->dev);
  err3:
 	iounmap(hcd->regs);
  err2:
@@ -349,12 +377,14 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device
  */
 void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 {
+	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+
 	usb_remove_hcd(hcd);
-	pxa27x_stop_hc(&pdev->dev);
+	pxa27x_stop_hc(ohci, &pdev->dev);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 	usb_put_hcd(hcd);
-	clk_put(usb_clk);
+	clk_put(ohci->clk);
 }
 
 /*-------------------------------------------------------------------------*/
@@ -387,7 +417,7 @@ ohci_pxa27x_start (struct usb_hcd *hcd)
 static const struct hc_driver ohci_pxa27x_hc_driver = {
 	.description =		hcd_name,
 	.product_desc =		"PXA27x OHCI",
-	.hcd_priv_size =	sizeof(struct ohci_hcd),
+	.hcd_priv_size =	sizeof(struct pxa27x_ohci),
 
 	/*
 	 * generic hardware linkage
@@ -451,13 +481,13 @@ static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
 static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
 
-	if (time_before(jiffies, ohci->next_statechange))
+	if (time_before(jiffies, ohci->ohci.next_statechange))
 		msleep(5);
-	ohci->next_statechange = jiffies;
+	ohci->ohci.next_statechange = jiffies;
 
-	pxa27x_stop_hc(&pdev->dev);
+	pxa27x_stop_hc(ohci, &pdev->dev);
 	hcd->state = HC_STATE_SUSPENDED;
 
 	return 0;
@@ -466,14 +496,14 @@ static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_
 static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
-	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
 	int status;
 
-	if (time_before(jiffies, ohci->next_statechange))
+	if (time_before(jiffies, ohci->ohci.next_statechange))
 		msleep(5);
-	ohci->next_statechange = jiffies;
+	ohci->ohci.next_statechange = jiffies;
 
-	if ((status = pxa27x_start_hc(&pdev->dev)) < 0)
+	if ((status = pxa27x_start_hc(ohci, &pdev->dev)) < 0)
 		return status;
 
 	ohci_finish_controller_resume(hcd);