Merge branch 'janitor'

drivers/net/3c523.c

@@ -105,6 +105,7 @@
 #include <linux/mca-legacy.h>
 #include <linux/ethtool.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/uaccess.h>
 #include <asm/processor.h>
@@ -658,7 +659,7 @@ static int init586(struct net_device *dev)
 
 	s = jiffies;		/* warning: only active with interrupts on !! */
 	while (!(cfg_cmd->cmd_status & STAT_COMPL)) {
-		if (jiffies - s > 30*HZ/100)
+		if (time_after(jiffies, s + 30*HZ/100))
 			break;
 	}
 
@@ -684,7 +685,7 @@ static int init586(struct net_device *dev)
 
 	s = jiffies;
 	while (!(ias_cmd->cmd_status & STAT_COMPL)) {
-		if (jiffies - s > 30*HZ/100)
+		if (time_after(jiffies, s + 30*HZ/100))
 			break;
 	}
 
@@ -709,7 +710,7 @@ static int init586(struct net_device *dev)
 
 	s = jiffies;
 	while (!(tdr_cmd->cmd_status & STAT_COMPL)) {
-		if (jiffies - s > 30*HZ/100) {
+		if (time_after(jiffies, s + 30*HZ/100)) {
 			printk(KERN_WARNING "%s: %d Problems while running the TDR.\n", dev->name, __LINE__);
 			result = 1;
 			break;
@@ -798,7 +799,7 @@ static int init586(struct net_device *dev)
 			elmc_id_attn586();
 			s = jiffies;
 			while (!(mc_cmd->cmd_status & STAT_COMPL)) {
-				if (jiffies - s > 30*HZ/100)
+				if (time_after(jiffies, s + 30*HZ/100))
 					break;
 			}
 			if (!(mc_cmd->cmd_status & STAT_COMPL)) {

drivers/net/3c59x.c

@@ -258,6 +258,7 @@ static int vortex_debug = 1;
 #include <linux/highmem.h>
 #include <linux/eisa.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 #include <asm/irq.h>			/* For NR_IRQS only. */
 #include <asm/io.h>
 #include <asm/uaccess.h>
@@ -2717,7 +2718,7 @@ boomerang_rx(struct net_device *dev)
 			skb = dev_alloc_skb(PKT_BUF_SZ);
 			if (skb == NULL) {
 				static unsigned long last_jif;
-				if ((jiffies - last_jif) > 10 * HZ) {
+				if (time_after(jiffies, last_jif + 10 * HZ)) {
 					printk(KERN_WARNING "%s: memory shortage\n", dev->name);
 					last_jif = jiffies;
 				}

drivers/net/apne.c

@@ -36,6 +36,7 @@
 #include <linux/delay.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -216,7 +217,7 @@ static int __init apne_probe1(struct net_device *dev, int ioaddr)
 	outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET);
 
 	while ((inb(ioaddr + NE_EN0_ISR) & ENISR_RESET) == 0)
-		if (jiffies - reset_start_time > 2*HZ/100) {
+		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 			printk(" not found (no reset ack).\n");
 			return -ENODEV;
 		}
@@ -382,7 +383,7 @@ apne_reset_8390(struct net_device *dev)
 
     /* This check _should_not_ be necessary, omit eventually. */
     while ((inb(NE_BASE+NE_EN0_ISR) & ENISR_RESET) == 0)
-	if (jiffies - reset_start_time > 2*HZ/100) {
+	if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 	    printk("%s: ne_reset_8390() did not complete.\n", dev->name);
 	    break;
 	}
@@ -530,7 +531,7 @@ apne_block_output(struct net_device *dev, int count,
     dma_start = jiffies;
 
     while ((inb(NE_BASE + NE_EN0_ISR) & ENISR_RDC) == 0)
-	if (jiffies - dma_start > 2*HZ/100) {		/* 20ms */
+	if (time_after(jiffies, dma_start + 2*HZ/100)) {	/* 20ms */
 		printk("%s: timeout waiting for Tx RDC.\n", dev->name);
 		apne_reset_8390(dev);
 		NS8390_init(dev,1);

drivers/net/arcnet/arc-rawmode.c

@@ -42,7 +42,7 @@ static int build_header(struct sk_buff *skb, struct net_device *dev,
 static int prepare_tx(struct net_device *dev, struct archdr *pkt, int length,
 		      int bufnum);
 
-struct ArcProto rawmode_proto =
+static struct ArcProto rawmode_proto =
 {
 	.suffix		= 'r',
 	.mtu		= XMTU,

drivers/net/arcnet/arcnet.c

@@ -52,6 +52,7 @@
 #include <net/arp.h>
 #include <linux/init.h>
 #include <linux/arcdevice.h>
+#include <linux/jiffies.h>
 
 /* "do nothing" functions for protocol drivers */
 static void null_rx(struct net_device *dev, int bufnum,
@@ -61,6 +62,7 @@ static int null_build_header(struct sk_buff *skb, struct net_device *dev,
 static int null_prepare_tx(struct net_device *dev, struct archdr *pkt,
 			   int length, int bufnum);
 
+static void arcnet_rx(struct net_device *dev, int bufnum);
 
 /*
  * one ArcProto per possible proto ID.  None of the elements of
@@ -71,7 +73,7 @@ static int null_prepare_tx(struct net_device *dev, struct archdr *pkt,
  struct ArcProto *arc_proto_map[256], *arc_proto_default,
    *arc_bcast_proto, *arc_raw_proto;
 
-struct ArcProto arc_proto_null =
+static struct ArcProto arc_proto_null =
 {
 	.suffix		= '?',
 	.mtu		= XMTU,
@@ -90,7 +92,6 @@ EXPORT_SYMBOL(arc_proto_map);
 EXPORT_SYMBOL(arc_proto_default);
 EXPORT_SYMBOL(arc_bcast_proto);
 EXPORT_SYMBOL(arc_raw_proto);
-EXPORT_SYMBOL(arc_proto_null);
 EXPORT_SYMBOL(arcnet_unregister_proto);
 EXPORT_SYMBOL(arcnet_debug);
 EXPORT_SYMBOL(alloc_arcdev);
@@ -118,7 +119,7 @@ static int __init arcnet_init(void)
 
 	arcnet_debug = debug;
 
-	printk(VERSION);
+	printk("arcnet loaded.\n");
 
 #ifdef ALPHA_WARNING
 	BUGLVL(D_EXTRA) {
@@ -178,8 +179,8 @@ EXPORT_SYMBOL(arcnet_dump_skb);
  * Dump the contents of an ARCnet buffer
  */
 #if (ARCNET_DEBUG_MAX & (D_RX | D_TX))
-void arcnet_dump_packet(struct net_device *dev, int bufnum, char *desc,
-			int take_arcnet_lock)
+static void arcnet_dump_packet(struct net_device *dev, int bufnum,
+			       char *desc, int take_arcnet_lock)
 {
 	struct arcnet_local *lp = dev->priv;
 	int i, length;
@@ -208,7 +209,10 @@ void arcnet_dump_packet(struct net_device *dev, int bufnum, char *desc,
 
 }
 
-EXPORT_SYMBOL(arcnet_dump_packet);
+#else
+
+#define arcnet_dump_packet(dev, bufnum, desc,take_arcnet_lock) do { } while (0)
+
 #endif
 
 
@@ -733,7 +737,7 @@ static void arcnet_timeout(struct net_device *dev)
 	
 	spin_unlock_irqrestore(&lp->lock, flags);
 
-	if (jiffies - lp->last_timeout > 10*HZ) {
+	if (time_after(jiffies, lp->last_timeout + 10*HZ)) {
 		BUGMSG(D_EXTRA, "tx timed out%s (status=%Xh, intmask=%Xh, dest=%02Xh)\n",
 		       msg, status, lp->intmask, lp->lasttrans_dest);
 		lp->last_timeout = jiffies;
@@ -996,7 +1000,7 @@ irqreturn_t arcnet_interrupt(int irq, void *dev_id, struct pt_regs *regs)
  * This is a generic packet receiver that calls arcnet??_rx depending on the
  * protocol ID found.
  */
-void arcnet_rx(struct net_device *dev, int bufnum)
+static void arcnet_rx(struct net_device *dev, int bufnum)
 {
 	struct arcnet_local *lp = dev->priv;
 	struct archdr pkt;

drivers/net/arcnet/rfc1051.c

@@ -43,7 +43,7 @@ static int prepare_tx(struct net_device *dev, struct archdr *pkt, int length,
 		      int bufnum);
 
 
-struct ArcProto rfc1051_proto =
+static struct ArcProto rfc1051_proto =
 {
 	.suffix		= 's',
 	.mtu		= XMTU - RFC1051_HDR_SIZE,

drivers/net/arcnet/rfc1201.c

@@ -43,7 +43,7 @@ static int prepare_tx(struct net_device *dev, struct archdr *pkt, int length,
 		      int bufnum);
 static int continue_tx(struct net_device *dev, int bufnum);
 
-struct ArcProto rfc1201_proto =
+static struct ArcProto rfc1201_proto =
 {
 	.suffix		= 'a',
 	.mtu		= 1500,	/* could be more, but some receivers can't handle it... */

drivers/net/arm/etherh.c

@@ -46,6 +46,7 @@
 #include <linux/device.h>
 #include <linux/init.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/ecard.h>
@@ -355,7 +356,7 @@ etherh_block_output (struct net_device *dev, int count, const unsigned char *buf
 	dma_start = jiffies;
 
 	while ((readb (addr + EN0_ISR) & ENISR_RDC) == 0)
-		if (jiffies - dma_start > 2*HZ/100) { /* 20ms */
+		if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */
 			printk(KERN_ERR "%s: timeout waiting for TX RDC\n",
 				dev->name);
 			etherh_reset (dev);

drivers/net/eth16i.c

@@ -161,6 +161,7 @@ static char *version =
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>		  
 #include <asm/io.h>		  
@@ -754,7 +755,7 @@ static void eth16i_set_port(int ioaddr, int porttype)
 
 static int eth16i_send_probe_packet(int ioaddr, unsigned char *b, int l)
 {
-	int starttime;
+	unsigned long starttime;
 
 	outb(0xff, ioaddr + TX_STATUS_REG);
 
@@ -765,7 +766,7 @@ static int eth16i_send_probe_packet(int ioaddr, unsigned char *b, int l)
 	outb(TX_START | 1, ioaddr + TRANSMIT_START_REG); 
 
 	while( (inb(ioaddr + TX_STATUS_REG) & 0x80) == 0) {
-		if( (jiffies - starttime) > TX_TIMEOUT) {
+		if( time_after(jiffies, starttime + TX_TIMEOUT)) {
 			return -1;
 		}
 	}
@@ -775,18 +776,18 @@ static int eth16i_send_probe_packet(int ioaddr, unsigned char *b, int l)
 
 static int eth16i_receive_probe_packet(int ioaddr)
 {
-	int starttime;
+	unsigned long starttime;
 
 	starttime = jiffies;
 
 	while((inb(ioaddr + TX_STATUS_REG) & 0x20) == 0) {
-		if( (jiffies - starttime) > TX_TIMEOUT) {
+		if( time_after(jiffies, starttime + TX_TIMEOUT)) {
 
 			if(eth16i_debug > 1)
 				printk(KERN_DEBUG "Timeout occurred waiting transmit packet received\n");
 			starttime = jiffies;
 			while((inb(ioaddr + RX_STATUS_REG) & 0x80) == 0) {
-				if( (jiffies - starttime) > TX_TIMEOUT) {
+				if( time_after(jiffies, starttime + TX_TIMEOUT)) {
 					if(eth16i_debug > 1)
 						printk(KERN_DEBUG "Timeout occurred waiting receive packet\n");
 					return -1;

drivers/net/hamradio/baycom_epp.c

@@ -905,7 +905,7 @@ static int epp_open(struct net_device *dev)
 	/* autoprobe baud rate */
 	tstart = jiffies;
 	i = 0;
-	while ((signed)(jiffies-tstart-HZ/3) < 0) {
+	while (time_before(jiffies, tstart + HZ/3)) {
 		if (pp->ops->epp_read_addr(pp, &stat, 1, 0) != 1)
 			goto epptimeout;
 		if ((stat & (EPP_NRAEF|EPP_NRHF)) == EPP_NRHF) {

drivers/net/hp100.c

@@ -115,6 +115,7 @@
 #include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/io.h>
 
@@ -1499,7 +1500,7 @@ static int hp100_start_xmit_bm(struct sk_buff *skb, struct net_device *dev)
 		printk("hp100: %s: start_xmit_bm: No TX PDL available.\n", dev->name);
 #endif
 		/* not waited long enough since last tx? */
-		if (jiffies - dev->trans_start < HZ)
+		if (time_before(jiffies, dev->trans_start + HZ))
 			return -EAGAIN;
 
 		if (hp100_check_lan(dev))
@@ -1652,7 +1653,7 @@ static int hp100_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		printk("hp100: %s: start_xmit: tx free mem = 0x%x\n", dev->name, i);
 #endif
 		/* not waited long enough since last failed tx try? */
-		if (jiffies - dev->trans_start < HZ) {
+		if (time_before(jiffies, dev->trans_start + HZ)) {
 #ifdef HP100_DEBUG
 			printk("hp100: %s: trans_start timing problem\n",
 			       dev->name);

drivers/net/ne-h8300.c

@@ -27,6 +27,7 @@ static const char version1[] =
 #include <linux/delay.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -365,7 +366,7 @@ static void ne_reset_8390(struct net_device *dev)
 
 	/* This check _should_not_ be necessary, omit eventually. */
 	while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
-		if (jiffies - reset_start_time > 2*HZ/100) {
+		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 			printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name);
 			break;
 		}
@@ -580,7 +581,7 @@ retry:
 #endif
 
 	while ((inb_p(NE_BASE + EN0_ISR) & ENISR_RDC) == 0)
-		if (jiffies - dma_start > 2*HZ/100) {		/* 20ms */
+		if (time_after(jiffies, dma_start + 2*HZ/100)) {		/* 20ms */
 			printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
 			ne_reset_8390(dev);
 			NS8390_init(dev,1);

drivers/net/ne.c

@@ -50,6 +50,7 @@ static const char version2[] =
 #include <linux/delay.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -341,7 +342,7 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr)
 		outb(inb(ioaddr + NE_RESET), ioaddr + NE_RESET);
 
 		while ((inb_p(ioaddr + EN0_ISR) & ENISR_RESET) == 0)
-		if (jiffies - reset_start_time > 2*HZ/100) {
+		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 			if (bad_card) {
 				printk(" (warning: no reset ack)");
 				break;
@@ -580,7 +581,7 @@ static void ne_reset_8390(struct net_device *dev)
 
 	/* This check _should_not_ be necessary, omit eventually. */
 	while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
-		if (jiffies - reset_start_time > 2*HZ/100) {
+		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 			printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name);
 			break;
 		}
@@ -787,7 +788,7 @@ retry:
 #endif
 
 	while ((inb_p(nic_base + EN0_ISR) & ENISR_RDC) == 0)
-		if (jiffies - dma_start > 2*HZ/100) {		/* 20ms */
+		if (time_after(jiffies, dma_start + 2*HZ/100)) {		/* 20ms */
 			printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name);
 			ne_reset_8390(dev);
 			NS8390_init(dev,1);

drivers/net/ne2.c

@@ -75,6 +75,7 @@ static const char *version = "ne2.c:v0.91 Nov 16 1998 Wim Dumon <wimpie@kotnet.o
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -395,7 +396,7 @@ static int __init ne2_probe1(struct net_device *dev, int slot)
 		outb(inb(base_addr + NE_RESET), base_addr + NE_RESET);
 
 		while ((inb_p(base_addr + EN0_ISR) & ENISR_RESET) == 0)
-			if (jiffies - reset_start_time > 2*HZ/100) {
+			if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 				printk(" not found (no reset ack).\n");
 				retval = -ENODEV;
 				goto out;
@@ -548,7 +549,7 @@ static void ne_reset_8390(struct net_device *dev)
 
 	/* This check _should_not_ be necessary, omit eventually. */
 	while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0)
-		if (jiffies - reset_start_time > 2*HZ/100) {
+		if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 			printk("%s: ne_reset_8390() did not complete.\n", 
 					dev->name);
 			break;
@@ -749,7 +750,7 @@ retry:
 #endif
 
 	while ((inb_p(nic_base + EN0_ISR) & ENISR_RDC) == 0)
-		if (jiffies - dma_start > 2*HZ/100) {		/* 20ms */
+		if (time_after(jiffies, dma_start + 2*HZ/100)) {		/* 20ms */
 			printk("%s: timeout waiting for Tx RDC.\n", dev->name);
 			ne_reset_8390(dev);
 			NS8390_init(dev,1);

drivers/net/ns83820.c

@@ -116,6 +116,7 @@
 #include <linux/timer.h>
 #include <linux/if_vlan.h>
 #include <linux/rtnetlink.h>
+#include <linux/jiffies.h>
 
 #include <asm/io.h>
 #include <asm/uaccess.h>
@@ -1607,7 +1608,7 @@ static void ns83820_run_bist(struct net_device *ndev, const char *name, u32 enab
 {
 	struct ns83820 *dev = PRIV(ndev);
 	int timed_out = 0;
-	long start;
+	unsigned long start;
 	u32 status;
 	int loops = 0;
 
@@ -1625,7 +1626,7 @@ static void ns83820_run_bist(struct net_device *ndev, const char *name, u32 enab
 			break;
 		if (status & fail)
 			break;
-		if ((jiffies - start) >= HZ) {
+		if (time_after_eq(jiffies, start + HZ)) {
 			timed_out = 1;
 			break;
 		}

drivers/net/oaknet.c

@@ -20,6 +20,7 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/init.h>
+#include <linux/jiffies.h>
 
 #include <asm/board.h>
 #include <asm/io.h>
@@ -606,7 +607,7 @@ retry:
 #endif
 
 	while ((ei_ibp(base + EN0_ISR) & ENISR_RDC) == 0) {
-		if (jiffies - start > OAKNET_WAIT) {
+		if (time_after(jiffies, start + OAKNET_WAIT)) {
 			printk("%s: timeout waiting for Tx RDC.\n", dev->name);
 			oaknet_reset_8390(dev);
 			NS8390_init(dev, TRUE);

drivers/net/pcmcia/3c589_cs.c

@@ -39,6 +39,7 @@
 #include <linux/if_arp.h>
 #include <linux/ioport.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <pcmcia/cs_types.h>
 #include <pcmcia/cs.h>
@@ -796,7 +797,7 @@ static void media_check(unsigned long arg)
     media = inw(ioaddr+WN4_MEDIA) & 0xc810;
 
     /* Ignore collisions unless we've had no irq's recently */
-    if (jiffies - lp->last_irq < HZ) {
+    if (time_before(jiffies, lp->last_irq + HZ)) {
 	media &= ~0x0010;
     } else {
 	/* Try harder to detect carrier errors */

drivers/net/ppp_async.c

@@ -30,6 +30,7 @@
 #include <linux/ppp_channel.h>
 #include <linux/spinlock.h>
 #include <linux/init.h>
+#include <linux/jiffies.h>
 #include <asm/uaccess.h>
 #include <asm/string.h>
 
@@ -570,7 +571,7 @@ ppp_async_encode(struct asyncppp *ap)
 		 * character if necessary.
 		 */
 		if (islcp || flag_time == 0
-		    || jiffies - ap->last_xmit >= flag_time)
+		    || time_after_eq(jiffies, ap->last_xmit + flag_time))
 			*buf++ = PPP_FLAG;
 		ap->last_xmit = jiffies;
 		fcs = PPP_INITFCS;

drivers/net/s2io.c

@@ -72,8 +72,8 @@
 static char s2io_driver_name[] = "Neterion";
 static char s2io_driver_version[] = DRV_VERSION;
 
-int rxd_size[4] = {32,48,48,64};
-int rxd_count[4] = {127,85,85,63};
+static int rxd_size[4] = {32,48,48,64};
+static int rxd_count[4] = {127,85,85,63};
 
 static inline int RXD_IS_UP2DT(RxD_t *rxdp)
 {
@@ -2127,7 +2127,7 @@ static void stop_nic(struct s2io_nic *nic)
 	}
 }
 
-int fill_rxd_3buf(nic_t *nic, RxD_t *rxdp, struct sk_buff *skb)
+static int fill_rxd_3buf(nic_t *nic, RxD_t *rxdp, struct sk_buff *skb)
 {
 	struct net_device *dev = nic->dev;
 	struct sk_buff *frag_list;
@@ -2852,7 +2852,7 @@ static int wait_for_cmd_complete(nic_t * sp)
  *  void.
  */
 
-void s2io_reset(nic_t * sp)
+static void s2io_reset(nic_t * sp)
 {
 	XENA_dev_config_t __iomem *bar0 = sp->bar0;
 	u64 val64;
@@ -2940,7 +2940,7 @@ void s2io_reset(nic_t * sp)
  *  SUCCESS on success and FAILURE on failure.
  */
 
-int s2io_set_swapper(nic_t * sp)
+static int s2io_set_swapper(nic_t * sp)
 {
 	struct net_device *dev = sp->dev;
 	XENA_dev_config_t __iomem *bar0 = sp->bar0;
@@ -3089,7 +3089,7 @@ static int wait_for_msix_trans(nic_t *nic, int i)
 	return ret;
 }
 
-void restore_xmsi_data(nic_t *nic)
+static void restore_xmsi_data(nic_t *nic)
 {
 	XENA_dev_config_t __iomem *bar0 = nic->bar0;
 	u64 val64;
@@ -3180,7 +3180,7 @@ int s2io_enable_msi(nic_t *nic)
 	return 0;
 }
 
-int s2io_enable_msi_x(nic_t *nic)
+static int s2io_enable_msi_x(nic_t *nic)
 {
 	XENA_dev_config_t __iomem *bar0 = nic->bar0;
 	u64 tx_mat, rx_mat;
@@ -4128,7 +4128,7 @@ static void s2io_set_multicast(struct net_device *dev)
  *  as defined in errno.h file on failure.
  */
 
-int s2io_set_mac_addr(struct net_device *dev, u8 * addr)
+static int s2io_set_mac_addr(struct net_device *dev, u8 * addr)
 {
 	nic_t *sp = dev->priv;
 	XENA_dev_config_t __iomem *bar0 = sp->bar0;
@@ -5713,7 +5713,7 @@ static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp)
  *  void.
  */
 
-void s2io_link(nic_t * sp, int link)
+static void s2io_link(nic_t * sp, int link)
 {
 	struct net_device *dev = (struct net_device *) sp->dev;
 
@@ -5738,7 +5738,7 @@ void s2io_link(nic_t * sp, int link)
  *  returns the revision ID of the device.
  */
 
-int get_xena_rev_id(struct pci_dev *pdev)
+static int get_xena_rev_id(struct pci_dev *pdev)
 {
 	u8 id = 0;
 	int ret;
@@ -6343,7 +6343,7 @@ int __init s2io_starter(void)
  * Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
  */
 
-void s2io_closer(void)
+static void s2io_closer(void)
 {
 	pci_unregister_driver(&s2io_driver);
 	DBG_PRINT(INIT_DBG, "cleanup done\n");

drivers/net/s2io.h

@@ -64,7 +64,7 @@ typedef enum xena_max_outstanding_splits {
 #define	INTR_DBG	4
 
 /* Global variable that defines the present debug level of the driver. */
-int debug_level = ERR_DBG;	/* Default level. */
+static int debug_level = ERR_DBG;
 
 /* DEBUG message print. */
 #define DBG_PRINT(dbg_level, args...)  if(!(debug_level<dbg_level)) printk(args)
@@ -268,7 +268,7 @@ typedef struct stat_block {
 #define MAX_RX_RINGS 8
 
 /* FIFO mappings for all possible number of fifos configured */
-int fifo_map[][MAX_TX_FIFOS] = {
+static int fifo_map[][MAX_TX_FIFOS] = {
 	{0, 0, 0, 0, 0, 0, 0, 0},
 	{0, 0, 0, 0, 1, 1, 1, 1},
 	{0, 0, 0, 1, 1, 1, 2, 2},
@@ -911,18 +911,16 @@ static void tx_intr_handler(fifo_info_t *fifo_data);
 static void alarm_intr_handler(struct s2io_nic *sp);
 
 static int s2io_starter(void);
-void s2io_closer(void);
 static void s2io_tx_watchdog(struct net_device *dev);
 static void s2io_tasklet(unsigned long dev_addr);
 static void s2io_set_multicast(struct net_device *dev);
 static int rx_osm_handler(ring_info_t *ring_data, RxD_t * rxdp);
-void s2io_link(nic_t * sp, int link);
-void s2io_reset(nic_t * sp);
+static void s2io_link(nic_t * sp, int link);
 #if defined(CONFIG_S2IO_NAPI)
 static int s2io_poll(struct net_device *dev, int *budget);
 #endif
 static void s2io_init_pci(nic_t * sp);
-int s2io_set_mac_addr(struct net_device *dev, u8 * addr);
+static int s2io_set_mac_addr(struct net_device *dev, u8 * addr);
 static void s2io_alarm_handle(unsigned long data);
 static int s2io_enable_msi(nic_t *nic);
 static irqreturn_t s2io_msi_handle(int irq, void *dev_id, struct pt_regs *regs);
@@ -930,14 +928,13 @@ static irqreturn_t
 s2io_msix_ring_handle(int irq, void *dev_id, struct pt_regs *regs);
 static irqreturn_t
 s2io_msix_fifo_handle(int irq, void *dev_id, struct pt_regs *regs);
-int s2io_enable_msi_x(nic_t *nic);
 static irqreturn_t s2io_isr(int irq, void *dev_id, struct pt_regs *regs);
 static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag);
 static struct ethtool_ops netdev_ethtool_ops;
 static void s2io_set_link(unsigned long data);
-int s2io_set_swapper(nic_t * sp);
+static int s2io_set_swapper(nic_t * sp);
 static void s2io_card_down(nic_t *nic);
 static int s2io_card_up(nic_t *nic);
-int get_xena_rev_id(struct pci_dev *pdev);
-void restore_xmsi_data(nic_t *nic);
+static int get_xena_rev_id(struct pci_dev *pdev);
+static void restore_xmsi_data(nic_t *nic);
 #endif				/* _S2IO_H */

drivers/net/seeq8005.c

@@ -46,6 +46,7 @@ static const char version[] =
 #include <linux/etherdevice.h>
 #include <linux/skbuff.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/io.h>
@@ -699,7 +700,7 @@ static void hardware_send_packet(struct net_device * dev, char *buf, int length)
 	int ioaddr = dev->base_addr;
 	int status = inw(SEEQ_STATUS);
 	int transmit_ptr = 0;
-	int tmp;
+	unsigned long tmp;
 
 	if (net_debug>4) {
 		printk("%s: send 0x%04x\n",dev->name,length);
@@ -724,7 +725,7 @@ static void hardware_send_packet(struct net_device * dev, char *buf, int length)
 	
 	/* drain FIFO */
 	tmp = jiffies;
-	while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && (jiffies - tmp < HZ))
+	while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && time_before(jiffies, tmp + HZ))
 		mb();
 	
 	/* doit ! */

drivers/net/shaper.c

@@ -83,6 +83,7 @@
 #include <linux/if_arp.h>
 #include <linux/init.h>
 #include <linux/if_shaper.h>
+#include <linux/jiffies.h>
 
 #include <net/dst.h>
 #include <net/arp.h>
@@ -168,7 +169,7 @@ static int shaper_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		/*
 		 *	Queue over time. Spill packet.
 		 */
-		if(SHAPERCB(skb)->shapeclock-jiffies > SHAPER_LATENCY) {
+		if(time_after(SHAPERCB(skb)->shapeclock,jiffies + SHAPER_LATENCY)) {
 			dev_kfree_skb(skb);
 			shaper->stats.tx_dropped++;
 		} else

drivers/net/sk98lin/h/skaddr.h

@@ -236,18 +236,6 @@ extern	int	SkAddrMcClear(
 	SK_U32	PortNumber,
 	int	Flags);
 
-extern	int	SkAddrXmacMcClear(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	Flags);
-
-extern	int	SkAddrGmacMcClear(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	Flags);
-
 extern	int	SkAddrMcAdd(
 	SK_AC		*pAC,
 	SK_IOC		IoC,
@@ -255,35 +243,11 @@ extern	int	SkAddrMcAdd(
 	SK_MAC_ADDR	*pMc,
 	int		Flags);
 
-extern	int	SkAddrXmacMcAdd(
-	SK_AC		*pAC,
-	SK_IOC		IoC,
-	SK_U32		PortNumber,
-	SK_MAC_ADDR	*pMc,
-	int		Flags);
-
-extern	int	SkAddrGmacMcAdd(
-	SK_AC		*pAC,
-	SK_IOC		IoC,
-	SK_U32		PortNumber,
-	SK_MAC_ADDR	*pMc,
-	int		Flags);
-
 extern	int	SkAddrMcUpdate(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
 	SK_U32	PortNumber);
 
-extern	int	SkAddrXmacMcUpdate(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber);
-
-extern	int	SkAddrGmacMcUpdate(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber);
-
 extern	int	SkAddrOverride(
 	SK_AC		*pAC,
 	SK_IOC		IoC,
@@ -297,18 +261,6 @@ extern	int	SkAddrPromiscuousChange(
 	SK_U32	PortNumber,
 	int	NewPromMode);
 
-extern	int	SkAddrXmacPromiscuousChange(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	NewPromMode);
-
-extern	int	SkAddrGmacPromiscuousChange(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	NewPromMode);	
-
 #ifndef SK_SLIM
 extern	int	SkAddrSwap(
 	SK_AC	*pAC,

drivers/net/sk98lin/h/skcsum.h

@@ -203,12 +203,6 @@ extern SKCS_STATUS SkCsGetReceiveInfo(
 	unsigned	Checksum2,
 	int			NetNumber);
 
-extern void SkCsGetSendInfo(
-	SK_AC				*pAc,
-	void				*pIpHeader,
-	SKCS_PACKET_INFO	*pPacketInfo,
-	int					NetNumber);
-
 extern void SkCsSetReceiveFlags(
 	SK_AC		*pAc,
 	unsigned	ReceiveFlags,

drivers/net/sk98lin/h/skgeinit.h

@@ -464,12 +464,6 @@ typedef	struct s_GeInit {
 /*
  * public functions in skgeinit.c
  */
-extern void	SkGePollRxD(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port,
-	SK_BOOL	PollRxD);
-
 extern void	SkGePollTxD(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
@@ -522,10 +516,6 @@ extern void	SkGeXmitLED(
 	int		Led,
 	int		Mode);
 
-extern void	SkGeInitRamIface(
-	SK_AC	*pAC,
-	SK_IOC	IoC);
-
 extern int	SkGeInitAssignRamToQueues(
 	SK_AC	*pAC,
 	int		ActivePort,
@@ -549,11 +539,6 @@ extern void	SkMacHardRst(
 	SK_IOC	IoC,
 	int		Port);
 
-extern void	SkMacClearRst(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port);
-
 extern void	SkXmInitMac(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
@@ -580,11 +565,6 @@ extern void	SkMacFlushTxFifo(
 	SK_IOC	IoC,
 	int		Port);
 
-extern void	SkMacFlushRxFifo(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port);
-
 extern void	SkMacIrq(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
@@ -601,12 +581,6 @@ extern void	SkMacAutoNegLipaPhy(
 	int		Port,
 	SK_U16	IStatus);
 
-extern void  SkMacSetRxTxEn(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port,
-	int		Para);
-
 extern int  SkMacRxTxEnable(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
@@ -659,16 +633,6 @@ extern void	SkXmClrExactAddr(
 	int		StartNum,
 	int		StopNum);
 
-extern void	SkXmInitDupMd(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port);
-
-extern void	SkXmInitPauseMd(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port);
-
 extern void	SkXmAutoNegLipaXmac(
 	SK_AC	*pAC,
 	SK_IOC	IoC,
@@ -729,17 +693,6 @@ extern int SkGmCableDiagStatus(
 	int		Port,
 	SK_BOOL	StartTest);
 
-extern int SkGmEnterLowPowerMode(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port,
-	SK_U8	Mode);
-
-extern int SkGmLeaveLowPowerMode(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int		Port);
-
 #ifdef SK_DIAG
 extern void	SkGePhyRead(
 	SK_AC	*pAC,
@@ -782,7 +735,6 @@ extern void	SkXmSendCont(
 /*
  * public functions in skgeinit.c
  */
-extern void	SkGePollRxD();
 extern void	SkGePollTxD();
 extern void	SkGeYellowLED();
 extern int	SkGeCfgSync();
@@ -792,7 +744,6 @@ extern int	SkGeInit();
 extern void	SkGeDeInit();
 extern int	SkGeInitPort();
 extern void	SkGeXmitLED();
-extern void	SkGeInitRamIface();
 extern int	SkGeInitAssignRamToQueues();
 
 /*
@@ -801,18 +752,15 @@ extern int	SkGeInitAssignRamToQueues();
 extern void SkMacRxTxDisable();
 extern void	SkMacSoftRst();
 extern void	SkMacHardRst();
-extern void	SkMacClearRst();
 extern void SkMacInitPhy();
 extern int  SkMacRxTxEnable();
 extern void SkMacPromiscMode();
 extern void SkMacHashing();
 extern void SkMacIrqDisable();
 extern void	SkMacFlushTxFifo();
-extern void	SkMacFlushRxFifo();
 extern void	SkMacIrq();
 extern int	SkMacAutoNegDone();
 extern void	SkMacAutoNegLipaPhy();
-extern void SkMacSetRxTxEn();
 extern void	SkXmInitMac();
 extern void	SkXmPhyRead();
 extern void	SkXmPhyWrite();
@@ -820,8 +768,6 @@ extern void	SkGmInitMac();
 extern void	SkGmPhyRead();
 extern void	SkGmPhyWrite();
 extern void	SkXmClrExactAddr();
-extern void	SkXmInitDupMd();
-extern void	SkXmInitPauseMd();
 extern void	SkXmAutoNegLipaXmac();
 extern int	SkXmUpdateStats();
 extern int	SkGmUpdateStats();
@@ -832,8 +778,6 @@ extern int	SkGmResetCounter();
 extern int	SkXmOverflowStatus();
 extern int	SkGmOverflowStatus();
 extern int	SkGmCableDiagStatus();
-extern int	SkGmEnterLowPowerMode();
-extern int	SkGmLeaveLowPowerMode();
 
 #ifdef SK_DIAG
 extern void	SkGePhyRead();

drivers/net/sk98lin/h/skgepnmi.h

@@ -946,10 +946,6 @@ typedef struct s_PnmiData {
  * Function prototypes
  */
 extern int SkPnmiInit(SK_AC *pAC, SK_IOC IoC, int Level);
-extern int SkPnmiGetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void* pBuf,
-	unsigned int* pLen, SK_U32 Instance, SK_U32 NetIndex);
-extern int SkPnmiPreSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id,
-	void* pBuf, unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex);
 extern int SkPnmiSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void* pBuf,
 	unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex);
 extern int SkPnmiGetStruct(SK_AC *pAC, SK_IOC IoC, void* pBuf,

drivers/net/sk98lin/h/skgesirq.h

@@ -105,7 +105,6 @@
 
 extern void SkGeSirqIsr(SK_AC *pAC, SK_IOC IoC, SK_U32 Istatus);
 extern int  SkGeSirqEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, SK_EVPARA Para);
-extern void SkHWLinkUp(SK_AC *pAC, SK_IOC IoC, int Port);
 extern void SkHWLinkDown(SK_AC *pAC, SK_IOC IoC, int Port);
 
 #endif	/* _INC_SKGESIRQ_H_ */

drivers/net/sk98lin/h/ski2c.h

@@ -162,9 +162,6 @@ typedef	struct	s_I2c {
 } SK_I2C;
 
 extern int SkI2cInit(SK_AC *pAC, SK_IOC IoC, int Level);
-extern int SkI2cWrite(SK_AC *pAC, SK_IOC IoC, SK_U32 Data, int Dev, int Size,
-					   int Reg, int Burst);
-extern int SkI2cReadSensor(SK_AC *pAC, SK_IOC IoC, SK_SENSOR *pSen);
 #ifdef SK_DIAG
 extern	SK_U32 SkI2cRead(SK_AC *pAC, SK_IOC IoC, int Dev, int Size, int Reg,
 						 int Burst);

drivers/net/sk98lin/h/skvpd.h

@@ -183,14 +183,6 @@ extern SK_U32	VpdReadDWord(
 	int			addr);
 #endif	/* SKDIAG */
 
-extern int	VpdSetupPara(
-	SK_AC		*pAC,
-	const char	*key,
-	const char	*buf,
-	int			len,
-	int			type,
-	int			op);
-
 extern SK_VPD_STATUS	*VpdStat(
 	SK_AC		*pAC,
 	SK_IOC		IoC);
@@ -227,11 +219,6 @@ extern int	VpdUpdate(
 	SK_AC		*pAC,
 	SK_IOC		IoC);
 
-extern void	VpdErrLog(
-	SK_AC		*pAC,
-	SK_IOC		IoC,
-	char		*msg);
-
 #ifdef	SKDIAG
 extern int	VpdReadBlock(
 	SK_AC		*pAC,
@@ -249,7 +236,6 @@ extern int	VpdWriteBlock(
 #endif	/* SKDIAG */
 #else	/* SK_KR_PROTO */
 extern SK_U32	VpdReadDWord();
-extern int	VpdSetupPara();
 extern SK_VPD_STATUS	*VpdStat();
 extern int	VpdKeys();
 extern int	VpdRead();
@@ -257,7 +243,6 @@ extern SK_BOOL	VpdMayWrite();
 extern int	VpdWrite();
 extern int	VpdDelete();
 extern int	VpdUpdate();
-extern void	VpdErrLog();
 #endif	/* SK_KR_PROTO */
 
 #endif	/* __INC_SKVPD_H_ */

drivers/net/sk98lin/skaddr.c

@@ -87,6 +87,21 @@ static const SK_U16	OnesHash[4] = {0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF};
 static int	Next0[SK_MAX_MACS] = {0};
 #endif	/* DEBUG */
 
+static int SkAddrGmacMcAdd(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber,
+			   SK_MAC_ADDR *pMc, int Flags);
+static int SkAddrGmacMcClear(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber,
+			     int Flags);
+static int SkAddrGmacMcUpdate(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber);
+static int SkAddrGmacPromiscuousChange(SK_AC *pAC, SK_IOC IoC,
+				       SK_U32 PortNumber, int NewPromMode);
+static int SkAddrXmacMcAdd(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber,
+			   SK_MAC_ADDR *pMc, int Flags);
+static int SkAddrXmacMcClear(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber,
+			     int Flags);
+static int SkAddrXmacMcUpdate(SK_AC *pAC, SK_IOC IoC, SK_U32 PortNumber);
+static int SkAddrXmacPromiscuousChange(SK_AC *pAC, SK_IOC IoC,
+				       SK_U32 PortNumber, int NewPromMode);
+
 /* functions ******************************************************************/
 
 /******************************************************************************
@@ -372,7 +387,7 @@ int		Flags)		/* permanent/non-perm, sw-only */
  *	SK_ADDR_SUCCESS
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrXmacMcClear(
+static int	SkAddrXmacMcClear(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* I/O context */
 SK_U32	PortNumber,	/* Index of affected port */
@@ -429,7 +444,7 @@ int		Flags)		/* permanent/non-perm, sw-only */
  *	SK_ADDR_SUCCESS
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrGmacMcClear(
+static int	SkAddrGmacMcClear(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* I/O context */
 SK_U32	PortNumber,	/* Index of affected port */
@@ -519,7 +534,7 @@ int		Flags)		/* permanent/non-perm, sw-only */
  * Returns:
  *	Hash value of multicast address.
  */
-SK_U32 SkXmacMcHash(
+static SK_U32 SkXmacMcHash(
 unsigned char *pMc)	/* Multicast address */
 {
 	SK_U32 Idx;
@@ -557,7 +572,7 @@ unsigned char *pMc)	/* Multicast address */
  * Returns:
  *	Hash value of multicast address.
  */
-SK_U32 SkGmacMcHash(
+static SK_U32 SkGmacMcHash(
 unsigned char *pMc)	/* Multicast address */
 {
 	SK_U32 Data;
@@ -672,7 +687,7 @@ int			Flags)		/* permanent/non-permanent */
  *	SK_MC_ILLEGAL_ADDRESS
  *	SK_MC_RLMT_OVERFLOW
  */
-int	SkAddrXmacMcAdd(
+static int	SkAddrXmacMcAdd(
 SK_AC		*pAC,		/* adapter context */
 SK_IOC		IoC,		/* I/O context */
 SK_U32		PortNumber,	/* Port Number */
@@ -778,7 +793,7 @@ int		Flags)		/* permanent/non-permanent */
  *	SK_MC_FILTERING_INEXACT
  *	SK_MC_ILLEGAL_ADDRESS
  */
-int	SkAddrGmacMcAdd(
+static int	SkAddrGmacMcAdd(
 SK_AC		*pAC,		/* adapter context */
 SK_IOC		IoC,		/* I/O context */
 SK_U32		PortNumber,	/* Port Number */
@@ -937,7 +952,7 @@ SK_U32	PortNumber)	/* Port Number */
  *	SK_MC_FILTERING_INEXACT
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrXmacMcUpdate(
+static int	SkAddrXmacMcUpdate(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* I/O context */
 SK_U32	PortNumber)	/* Port Number */
@@ -1082,7 +1097,7 @@ SK_U32	PortNumber)	/* Port Number */
  *	SK_MC_FILTERING_INEXACT
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrGmacMcUpdate(
+static int	SkAddrGmacMcUpdate(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* I/O context */
 SK_U32	PortNumber)	/* Port Number */
@@ -1468,7 +1483,7 @@ int		NewPromMode)	/* new promiscuous mode */
  *	SK_ADDR_SUCCESS
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrXmacPromiscuousChange(
+static int	SkAddrXmacPromiscuousChange(
 SK_AC	*pAC,			/* adapter context */
 SK_IOC	IoC,			/* I/O context */
 SK_U32	PortNumber,		/* port whose promiscuous mode changes */
@@ -1585,7 +1600,7 @@ int		NewPromMode)	/* new promiscuous mode */
  *	SK_ADDR_SUCCESS
  *	SK_ADDR_ILLEGAL_PORT
  */
-int	SkAddrGmacPromiscuousChange(
+static int	SkAddrGmacPromiscuousChange(
 SK_AC	*pAC,			/* adapter context */
 SK_IOC	IoC,			/* I/O context */
 SK_U32	PortNumber,		/* port whose promiscuous mode changes */

drivers/net/sk98lin/skgeinit.c

@@ -57,34 +57,6 @@ static struct s_Config OemConfig = {
 #endif
 };
 
-/******************************************************************************
- *
- *	SkGePollRxD() - Enable / Disable Descriptor Polling of RxD Ring
- *
- * Description:
- *	Enable or disable the descriptor polling of the receive descriptor
- *	ring (RxD) for port 'Port'.
- *	The new configuration is *not* saved over any SkGeStopPort() and
- *	SkGeInitPort() calls.
- *
- * Returns:
- *	nothing
- */
-void SkGePollRxD(
-SK_AC	*pAC,		/* adapter context */
-SK_IOC	IoC,		/* IO context */
-int		Port,		/* Port Index (MAC_1 + n) */
-SK_BOOL PollRxD)	/* SK_TRUE (enable pol.), SK_FALSE (disable pol.) */
-{
-	SK_GEPORT *pPrt;
-
-	pPrt = &pAC->GIni.GP[Port];
-
-	SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), (PollRxD) ?
-		CSR_ENA_POL : CSR_DIS_POL);
-}	/* SkGePollRxD */
-
-
 /******************************************************************************
  *
  *	SkGePollTxD() - Enable / Disable Descriptor Polling of TxD Rings
@@ -952,7 +924,7 @@ int		Port)		/* Port Index (MAC_1 + n) */
  * Returns:
  *	nothing
  */
-void SkGeInitRamIface(
+static void SkGeInitRamIface(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC)		/* IO context */
 {
@@ -1409,83 +1381,6 @@ SK_IOC	IoC)		/* IO context */
 
 }	/* SkGeInit0*/
 
-#ifdef SK_PCI_RESET
-
-/******************************************************************************
- *
- *	SkGePciReset() - Reset PCI interface
- *
- * Description:
- *	o Read PCI configuration.
- *	o Change power state to 3.
- *	o Change power state to 0.
- *	o Restore PCI configuration.
- *
- * Returns:
- *	0:	Success.
- *	1:	Power state could not be changed to 3.
- */
-static int SkGePciReset(
-SK_AC	*pAC,		/* adapter context */
-SK_IOC	IoC)		/* IO context */
-{
-	int		i;
-	SK_U16	PmCtlSts;
-	SK_U32	Bp1;
-	SK_U32	Bp2;
-	SK_U16	PciCmd;
-	SK_U8	Cls;
-	SK_U8	Lat;
-	SK_U8	ConfigSpace[PCI_CFG_SIZE];
-
-	/*
-	 * Note: Switching to D3 state is like a software reset.
-	 *		 Switching from D3 to D0 is a hardware reset.
-	 *		 We have to save and restore the configuration space.
-	 */
-	for (i = 0; i < PCI_CFG_SIZE; i++) {
-		SkPciReadCfgDWord(pAC, i*4, &ConfigSpace[i]);
-	}
-
-	/* We know the RAM Interface Arbiter is enabled. */
-	SkPciWriteCfgWord(pAC, PCI_PM_CTL_STS, PCI_PM_STATE_D3);
-	SkPciReadCfgWord(pAC, PCI_PM_CTL_STS, &PmCtlSts);
-	
-	if ((PmCtlSts & PCI_PM_STATE_MSK) != PCI_PM_STATE_D3) {
-		return(1);
-	}
-
-	/* Return to D0 state. */
-	SkPciWriteCfgWord(pAC, PCI_PM_CTL_STS, PCI_PM_STATE_D0);
-
-	/* Check for D0 state. */
-	SkPciReadCfgWord(pAC, PCI_PM_CTL_STS, &PmCtlSts);
-	
-	if ((PmCtlSts & PCI_PM_STATE_MSK) != PCI_PM_STATE_D0) {
-		return(1);
-	}
-
-	/* Check PCI Config Registers. */
-	SkPciReadCfgWord(pAC, PCI_COMMAND, &PciCmd);
-	SkPciReadCfgByte(pAC, PCI_CACHE_LSZ, &Cls);
-	SkPciReadCfgDWord(pAC, PCI_BASE_1ST, &Bp1);
-	SkPciReadCfgDWord(pAC, PCI_BASE_2ND, &Bp2);
-	SkPciReadCfgByte(pAC, PCI_LAT_TIM, &Lat);
-	
-	if (PciCmd != 0 || Cls != (SK_U8)0 || Lat != (SK_U8)0 ||
-		(Bp1 & 0xfffffff0L) != 0 || Bp2 != 1) {
-		return(1);
-	}
-
-	/* Restore PCI Config Space. */
-	for (i = 0; i < PCI_CFG_SIZE; i++) {
-		SkPciWriteCfgDWord(pAC, i*4, ConfigSpace[i]);
-	}
-
-	return(0);
-}	/* SkGePciReset */
-
-#endif /* SK_PCI_RESET */
 
 /******************************************************************************
  *
@@ -1524,10 +1419,6 @@ SK_IOC	IoC)		/* IO context */
 	/* save CLK_RUN bits (YUKON-Lite) */
 	SK_IN16(IoC, B0_CTST, &CtrlStat);
 
-#ifdef SK_PCI_RESET
-	(void)SkGePciReset(pAC, IoC);
-#endif /* SK_PCI_RESET */
-
 	/* do the SW-reset */
 	SK_OUT8(IoC, B0_CTST, CS_RST_SET);
 
@@ -1991,11 +1882,6 @@ SK_IOC	IoC)		/* IO context */
 	int	i;
 	SK_U16	Word;
 
-#ifdef SK_PHY_LP_MODE
-	SK_U8	Byte;
-	SK_U16	PmCtlSts;
-#endif /* SK_PHY_LP_MODE */
-
 #if (!defined(SK_SLIM) && !defined(VCPU))
 	/* ensure I2C is ready */
 	SkI2cWaitIrq(pAC, IoC);
@@ -2010,38 +1896,6 @@ SK_IOC	IoC)		/* IO context */
 		}
 	}
 
-#ifdef SK_PHY_LP_MODE
-    /*
-	 * for power saving purposes within mobile environments
-	 * we set the PHY to coma mode and switch to D3 power state.
-	 */
-	if (pAC->GIni.GIYukonLite &&
-		pAC->GIni.GIChipRev >= CHIP_REV_YU_LITE_A3) {
-
-		/* for all ports switch PHY to coma mode */
-		for (i = 0; i < pAC->GIni.GIMacsFound; i++) {
-			
-			SkGmEnterLowPowerMode(pAC, IoC, i, PHY_PM_DEEP_SLEEP);
-		}
-
-		if (pAC->GIni.GIVauxAvail) {
-			/* switch power to VAUX */
-			Byte = PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_ON | PC_VCC_OFF;
-
-			SK_OUT8(IoC, B0_POWER_CTRL, Byte);
-		}
-		
-		/* switch to D3 state */
-		SK_IN16(IoC, PCI_C(PCI_PM_CTL_STS), &PmCtlSts);
-
-		PmCtlSts |= PCI_PM_STATE_D3;
-
-		SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-
-		SK_OUT16(IoC, PCI_C(PCI_PM_CTL_STS), PmCtlSts);
-	}
-#endif /* SK_PHY_LP_MODE */
-
 	/* Reset all bits in the PCI STATUS register */
 	/*
 	 * Note: PCI Cfg cycles cannot be used, because they are not

drivers/net/sk98lin/skgemib.c

@@ -871,13 +871,6 @@ PNMI_STATIC const SK_PNMI_TAB_ENTRY IdTable[] = {
 		sizeof(SK_PNMI_CONF),
 		SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyType),
 		SK_PNMI_RO, MacPrivateConf, 0},
-#ifdef SK_PHY_LP_MODE
-		{OID_SKGE_PHY_LP_MODE,
-		SK_PNMI_MAC_ENTRIES,
-		sizeof(SK_PNMI_CONF),
-		SK_PNMI_OFF(Conf) + SK_PNMI_CNF_OFF(ConfPhyMode),
-		SK_PNMI_RW, MacPrivateConf, 0},
-#endif	
 	{OID_SKGE_LINK_CAP,
 		SK_PNMI_MAC_ENTRIES,
 		sizeof(SK_PNMI_CONF),

drivers/net/sk98lin/skgepnmi.c

@@ -56,10 +56,6 @@ static const char SysKonnectFileId[] =
  * Public Function prototypes
  */
 int SkPnmiInit(SK_AC *pAC, SK_IOC IoC, int level);
-int SkPnmiGetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void *pBuf,
-	unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex);
-int SkPnmiPreSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void *pBuf,
-	unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex);
 int SkPnmiSetVar(SK_AC *pAC, SK_IOC IoC, SK_U32 Id, void *pBuf,
 	unsigned int *pLen, SK_U32 Instance, SK_U32 NetIndex);
 int SkPnmiGetStruct(SK_AC *pAC, SK_IOC IoC, void *pBuf,
@@ -587,7 +583,7 @@ int Level)		/* Initialization level */
  *                           exist (e.g. port instance 3 on a two port
  *	                         adapter.
  */
-int SkPnmiGetVar(
+static int SkPnmiGetVar(
 SK_AC *pAC,		/* Pointer to adapter context */
 SK_IOC IoC,		/* IO context handle */
 SK_U32 Id,		/* Object ID that is to be processed */
@@ -629,7 +625,7 @@ SK_U32 NetIndex)	/* NetIndex (0..n), in single net mode always zero */
  *                           exist (e.g. port instance 3 on a two port
  *	                         adapter.
  */
-int SkPnmiPreSetVar(
+static int SkPnmiPreSetVar(
 SK_AC *pAC,		/* Pointer to adapter context */
 SK_IOC IoC,		/* IO context handle */
 SK_U32 Id,		/* Object ID that is to be processed */
@@ -5062,9 +5058,6 @@ SK_U32 NetIndex)	/* NetIndex (0..n), in single net mode always zero */
 		case OID_SKGE_SPEED_CAP:
 		case OID_SKGE_SPEED_MODE:
 		case OID_SKGE_SPEED_STATUS:
-#ifdef SK_PHY_LP_MODE
-		case OID_SKGE_PHY_LP_MODE:
-#endif
 			if (*pLen < (Limit - LogPortIndex) * sizeof(SK_U8)) {
 
 				*pLen = (Limit - LogPortIndex) * sizeof(SK_U8);
@@ -5140,28 +5133,6 @@ SK_U32 NetIndex)	/* NetIndex (0..n), in single net mode always zero */
 				Offset += sizeof(SK_U32);
 				break;
 
-#ifdef SK_PHY_LP_MODE
-			case OID_SKGE_PHY_LP_MODE:
-				if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */
-					if (LogPortIndex == 0) {
-						continue;
-					}
-					else {
-						/* Get value for physical ports */
-						PhysPortIndex = SK_PNMI_PORT_LOG2PHYS(pAC, LogPortIndex);
-						Val8 = (SK_U8) pAC->GIni.GP[PhysPortIndex].PPhyPowerState;
-						*pBufPtr = Val8;
-					}
-				}
-				else { /* DualNetMode */
-					
-					Val8 = (SK_U8) pAC->GIni.GP[PhysPortIndex].PPhyPowerState;
-					*pBufPtr = Val8;
-				}
-				Offset += sizeof(SK_U8);
-				break;
-#endif
-
 			case OID_SKGE_LINK_CAP:
 				if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */
 					if (LogPortIndex == 0) {
@@ -5478,16 +5449,6 @@ SK_U32 NetIndex)	/* NetIndex (0..n), in single net mode always zero */
 		}
 		break;
 
-#ifdef SK_PHY_LP_MODE
-	case OID_SKGE_PHY_LP_MODE:
-		if (*pLen < Limit - LogPortIndex) {
-
-			*pLen = Limit - LogPortIndex;
-			return (SK_PNMI_ERR_TOO_SHORT);
-		}
-		break;
-#endif
-
 	case OID_SKGE_MTU:
 		if (*pLen < sizeof(SK_U32)) {
 
@@ -5845,116 +5806,6 @@ SK_U32 NetIndex)	/* NetIndex (0..n), in single net mode always zero */
 			Offset += sizeof(SK_U32);
 			break;
 		
-#ifdef SK_PHY_LP_MODE
-		case OID_SKGE_PHY_LP_MODE:
-			/* The preset ends here */
-			if (Action == SK_PNMI_PRESET) {
-
-				return (SK_PNMI_ERR_OK);
-			}
-
-			if (!pAC->Pnmi.DualNetActiveFlag) { /* SingleNetMode */
-				if (LogPortIndex == 0) {
-					Offset = 0;
-					continue;
-				}
-				else {
-					/* Set value for physical ports */
-					PhysPortIndex = SK_PNMI_PORT_LOG2PHYS(pAC, LogPortIndex);
-
-					switch (*(pBuf + Offset)) {
-						case 0:
-							/* If LowPowerMode is active, we can leave it. */
-							if (pAC->GIni.GP[PhysPortIndex].PPhyPowerState) {
-
-								Val32 = SkGmLeaveLowPowerMode(pAC, IoC, PhysPortIndex);
-								
-								if (pAC->GIni.GP[PhysPortIndex].PPhyPowerState < 3)	{
-									
-									SkDrvInitAdapter(pAC);
-								}
-								break;
-							}
-							else {
-								*pLen = 0;
-								return (SK_PNMI_ERR_GENERAL);
-							}
-						case 1:
-						case 2:
-						case 3:
-						case 4:
-							/* If no LowPowerMode is active, we can enter it. */
-							if (!pAC->GIni.GP[PhysPortIndex].PPhyPowerState) {
-
-								if ((*(pBuf + Offset)) < 3)	{
-								
-									SkDrvDeInitAdapter(pAC);
-								}
-
-								Val32 = SkGmEnterLowPowerMode(pAC, IoC, PhysPortIndex, *pBuf);
-								break;
-							}
-							else {
-								*pLen = 0;
-								return (SK_PNMI_ERR_GENERAL);
-							}
-						default:
-							*pLen = 0;
-							return (SK_PNMI_ERR_BAD_VALUE);
-					}
-				}
-			}
-			else { /* DualNetMode */
-				
-				switch (*(pBuf + Offset)) {
-					case 0:
-						/* If we are in a LowPowerMode, we can leave it. */
-						if (pAC->GIni.GP[PhysPortIndex].PPhyPowerState) {
-
-							Val32 = SkGmLeaveLowPowerMode(pAC, IoC, PhysPortIndex);
-							
-							if (pAC->GIni.GP[PhysPortIndex].PPhyPowerState < 3)	{
-
-								SkDrvInitAdapter(pAC);
-							}
-							break;
-						}
-						else {
-							*pLen = 0;
-							return (SK_PNMI_ERR_GENERAL);
-						}
-					
-					case 1:
-					case 2:
-					case 3:
-					case 4:
-						/* If we are not already in LowPowerMode, we can enter it. */
-						if (!pAC->GIni.GP[PhysPortIndex].PPhyPowerState) {
-
-							if ((*(pBuf + Offset)) < 3)	{
-
-								SkDrvDeInitAdapter(pAC);
-							}
-							else {
-
-								Val32 = SkGmEnterLowPowerMode(pAC, IoC, PhysPortIndex, *pBuf);
-							}
-							break;
-						}
-						else {
-							*pLen = 0;
-							return (SK_PNMI_ERR_GENERAL);
-						}
-					
-					default:
-						*pLen = 0;
-						return (SK_PNMI_ERR_BAD_VALUE);
-				}
-			}
-			Offset += sizeof(SK_U8);
-			break;
-#endif
-
 		default:
             SK_DBG_MSG(pAC, SK_DBGMOD_PNMI, SK_DBGCAT_ERR,
                 ("MacPrivateConf: Unknown OID should be handled before set"));

drivers/net/sk98lin/skgesirq.c

@@ -265,7 +265,7 @@ int		Port)		/* Port Index (MAC_1 + n) */
  *
  * Returns: N/A
  */
-void SkHWLinkUp(
+static void SkHWLinkUp(
 SK_AC	*pAC,	/* adapter context */
 SK_IOC	IoC,	/* IO context */
 int		Port)	/* Port Index (MAC_1 + n) */
@@ -612,14 +612,6 @@ SK_U32	Istatus)	/* Interrupt status word */
 				 * we ignore those
 				 */
 				pPrt->HalfDupTimerActive = SK_TRUE;
-#ifdef XXX
-				Len = sizeof(SK_U64);
-				SkPnmiGetVar(pAC, IoC, OID_SKGE_STAT_TX_OCTETS, (char *)&Octets,
-					&Len, (SK_U32)SK_PNMI_PORT_PHYS2INST(pAC, 0),
-					pAC->Rlmt.Port[0].Net->NetNumber);
-				
-				pPrt->LastOctets = Octets;
-#endif /* XXX */
 				/* Snap statistic counters */
 				(void)SkXmUpdateStats(pAC, IoC, 0);
 
@@ -653,14 +645,6 @@ SK_U32	Istatus)	/* Interrupt status word */
 				 pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOHALF) &&
 				!pPrt->HalfDupTimerActive) {
 				pPrt->HalfDupTimerActive = SK_TRUE;
-#ifdef XXX
-				Len = sizeof(SK_U64);
-				SkPnmiGetVar(pAC, IoC, OID_SKGE_STAT_TX_OCTETS, (char *)&Octets,
-					&Len, (SK_U32)SK_PNMI_PORT_PHYS2INST(pAC, 1),
-					pAC->Rlmt.Port[1].Net->NetNumber);
-				
-				pPrt->LastOctets = Octets;
-#endif /* XXX */
 				/* Snap statistic counters */
 				(void)SkXmUpdateStats(pAC, IoC, 1);
 
@@ -2085,12 +2069,6 @@ SK_EVPARA	Para)		/* Event specific Parameter */
 			pPrt->HalfDupTimerActive = SK_FALSE;
 			if (pPrt->PLinkModeStatus == SK_LMODE_STAT_HALF ||
 				pPrt->PLinkModeStatus == SK_LMODE_STAT_AUTOHALF) {
-#ifdef XXX
-				Len = sizeof(SK_U64);
-				SkPnmiGetVar(pAC, IoC, OID_SKGE_STAT_TX_OCTETS, (char *)&Octets,
-					&Len, (SK_U32)SK_PNMI_PORT_PHYS2INST(pAC, Port),
-					pAC->Rlmt.Port[Port].Net->NetNumber);
-#endif /* XXX */
 				/* Snap statistic counters */
 				(void)SkXmUpdateStats(pAC, IoC, Port);
 

drivers/net/sk98lin/ski2c.c

@@ -396,7 +396,7 @@ int		Rw)		/* Read / Write Flag */
  *			1:	error,	 transfer does not complete, I2C transfer
  *						 killed, wait loop terminated.
  */
-int	SkI2cWait(
+static int	SkI2cWait(
 SK_AC	*pAC,	/* Adapter Context */
 SK_IOC	IoC,	/* I/O Context */
 int		Event)	/* complete event to wait for (I2C_READ or I2C_WRITE) */
@@ -481,7 +481,7 @@ SK_IOC	IoC)	/* I/O Context */
  * returns	0:	success
  *			1:	error
  */
-int SkI2cWrite(
+static int SkI2cWrite(
 SK_AC	*pAC,		/* Adapter Context */
 SK_IOC	IoC,		/* I/O Context */
 SK_U32	I2cData,	/* I2C Data to write */
@@ -538,7 +538,7 @@ int		I2cBurst)	/* I2C Burst Flag */
  *		1 if the read is completed
  *		0 if the read must be continued (I2C Bus still allocated)
  */
-int	SkI2cReadSensor(
+static int	SkI2cReadSensor(
 SK_AC		*pAC,	/* Adapter Context */
 SK_IOC		IoC,	/* I/O Context */
 SK_SENSOR	*pSen)	/* Sensor to be read */

drivers/net/sk98lin/sklm80.c

@@ -34,79 +34,7 @@ static const char SysKonnectFileId[] =
 #include "h/lm80.h"
 #include "h/skdrv2nd.h"		/* Adapter Control- and Driver specific Def. */
 
-#ifdef	SK_DIAG
-#define	BREAK_OR_WAIT(pAC,IoC,Event)	SkI2cWait(pAC,IoC,Event)
-#else	/* nSK_DIAG */
 #define	BREAK_OR_WAIT(pAC,IoC,Event)	break
-#endif	/* nSK_DIAG */
-
-#ifdef	SK_DIAG
-/*
- * read the register 'Reg' from the device 'Dev'
- *
- * return 	read error	-1
- *		success		the read value
- */
-int	SkLm80RcvReg(
-SK_IOC	IoC,		/* Adapter Context */
-int		Dev,		/* I2C device address */
-int		Reg)		/* register to read */
-{
-	int	Val = 0;
-	int	TempExt;
-
-	/* Signal device number */
-	if (SkI2cSndDev(IoC, Dev, I2C_WRITE)) {
-		return(-1);
-	}
-
-	if (SkI2cSndByte(IoC, Reg)) {
-		return(-1);
-	}
-
-	/* repeat start */
-	if (SkI2cSndDev(IoC, Dev, I2C_READ)) {
-		return(-1);
-	}
-
-	switch (Reg) {
-	case LM80_TEMP_IN:
-		Val = (int)SkI2cRcvByte(IoC, 1);
-
-		/* First: correct the value: it might be negative */
-		if ((Val & 0x80) != 0) {
-			/* Value is negative */
-			Val = Val - 256;
-		}
-		Val = Val * SK_LM80_TEMP_LSB;
-		SkI2cStop(IoC);
-		
-		TempExt = (int)SkLm80RcvReg(IoC, LM80_ADDR, LM80_TEMP_CTRL);
-		
-		if (Val > 0) {
-			Val += ((TempExt >> 7) * SK_LM80_TEMPEXT_LSB);
-		}
-		else {
-			Val -= ((TempExt >> 7) * SK_LM80_TEMPEXT_LSB);
-		}
-		return(Val);
-		break;
-	case LM80_VT0_IN:
-	case LM80_VT1_IN:
-	case LM80_VT2_IN:
-	case LM80_VT3_IN:
-		Val = (int)SkI2cRcvByte(IoC, 1) * SK_LM80_VT_LSB;
-		break;
-	
-	default:
-		Val = (int)SkI2cRcvByte(IoC, 1);
-		break;
-	}
-
-	SkI2cStop(IoC);
-	return(Val);
-}
-#endif	/* SK_DIAG */
 
 /*
  * read a sensors value (LM80 specific)

drivers/net/sk98lin/skrlmt.c

@@ -282,7 +282,6 @@ typedef struct s_SpTreeRlmtPacket {
 
 SK_MAC_ADDR	SkRlmtMcAddr =	{{0x01,  0x00,  0x5A,  0x52,  0x4C,  0x4D}};
 SK_MAC_ADDR	BridgeMcAddr =	{{0x01,  0x80,  0xC2,  0x00,  0x00,  0x00}};
-SK_MAC_ADDR	BcAddr = 		{{0xFF,  0xFF,  0xFF,  0xFF,  0xFF,  0xFF}};
 
 /* local variables ************************************************************/
 

drivers/net/sk98lin/skvpd.c

@@ -132,65 +132,6 @@ int		addr)	/* VPD address */
 
 #endif	/* SKDIAG */
 
-#if 0
-
-/*
-	Write the dword 'data' at address 'addr' into the VPD EEPROM, and
-	verify that the data is written.
-
- Needed Time:
-
-.				MIN		MAX
-. -------------------------------------------------------------------
-. write				1.8 ms		3.6 ms
-. internal write cyles		0.7 ms		7.0 ms
-. -------------------------------------------------------------------
-. over all program time	 	2.5 ms		10.6 ms
-. read				1.3 ms		2.6 ms
-. -------------------------------------------------------------------
-. over all 			3.8 ms		13.2 ms
-.
-
-
- Returns	0:	success
-			1:	error,	I2C transfer does not terminate
-			2:	error,	data verify error
-
- */
-static int VpdWriteDWord(
-SK_AC	*pAC,	/* pAC pointer */
-SK_IOC	IoC,	/* IO Context */
-int		addr,	/* VPD address */
-SK_U32	data)	/* VPD data to write */
-{
-	/* start VPD write */
-	/* Don't swap here, it's a data stream of bytes */
-	SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_CTRL,
-		("VPD write dword at addr 0x%x, data = 0x%x\n",addr,data));
-	VPD_OUT32(pAC, IoC, PCI_VPD_DAT_REG, (SK_U32)data);
-	/* But do it here */
-	addr |= VPD_WRITE;
-
-	VPD_OUT16(pAC, IoC, PCI_VPD_ADR_REG, (SK_U16)(addr | VPD_WRITE));
-
-	/* this may take up to 10,6 ms */
-	if (VpdWait(pAC, IoC, VPD_WRITE)) {
-		SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR,
-			("Write Timed Out\n"));
-		return(1);
-	};
-
-	/* verify data */
-	if (VpdReadDWord(pAC, IoC, addr) != data) {
-		SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR | SK_DBGCAT_FATAL,
-			("Data Verify Error\n"));
-		return(2);
-	}
-	return(0);
-}	/* VpdWriteDWord */
-
-#endif	/* 0 */
-
 /*
  *	Read one Stream of 'len' bytes of VPD data, starting at 'addr' from
  *	or to the I2C EEPROM.
@@ -728,7 +669,7 @@ char	*etp)		/* end pointer input position */
  *		6:	fatal VPD error
  *
  */
-int	VpdSetupPara(
+static int	VpdSetupPara(
 SK_AC	*pAC,		/* common data base */
 const char	*key,	/* keyword to insert */
 const char	*buf,	/* buffer with the keyword value */
@@ -1148,50 +1089,3 @@ SK_IOC	IoC)	/* IO Context */
 	return(0);
 }
 
-
-
-/*
- *	Read the contents of the VPD EEPROM and copy it to the VPD buffer
- *	if not already done. If the keyword "VF" is not present it will be
- *	created and the error log message will be stored to this keyword.
- *	If "VF" is not present the error log message will be stored to the
- *	keyword "VL". "VL" will created or overwritten if "VF" is present.
- *	The VPD read/write area is saved to the VPD EEPROM.
- *
- * returns nothing, errors will be ignored.
- */
-void VpdErrLog(
-SK_AC	*pAC,	/* common data base */
-SK_IOC	IoC,	/* IO Context */
-char	*msg)	/* error log message */
-{
-	SK_VPD_PARA *v, vf;	/* VF */
-	int len;
-
-	SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX,
-		("VPD error log msg %s\n", msg));
-	if ((pAC->vpd.v.vpd_status & VPD_VALID) == 0) {
-		if (VpdInit(pAC, IoC) != 0) {
-			SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_ERR,
-				("VPD init error\n"));
-			return;
-		}
-	}
-
-	len = strlen(msg);
-	if (len > VPD_MAX_LEN) {
-		/* cut it */
-		len = VPD_MAX_LEN;
-	}
-	if ((v = vpd_find_para(pAC, VPD_VF, &vf)) != NULL) {
-		SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX, ("overwrite VL\n"));
-		(void)VpdSetupPara(pAC, VPD_VL, msg, len, VPD_RW_KEY, OWR_KEY);
-	}
-	else {
-		SK_DBG_MSG(pAC, SK_DBGMOD_VPD, SK_DBGCAT_TX, ("write VF\n"));
-		(void)VpdSetupPara(pAC, VPD_VF, msg, len, VPD_RW_KEY, ADD_KEY);
-	}
-
-	(void)VpdUpdate(pAC, IoC);
-}
-

drivers/net/sk98lin/skxmac2.c

@@ -41,13 +41,13 @@ static const char SysKonnectFileId[] =
 #endif
 
 #ifdef GENESIS
-BCOM_HACK BcomRegA1Hack[] = {
+static BCOM_HACK BcomRegA1Hack[] = {
  { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1104 }, { 0x17, 0x0013 },
  { 0x15, 0x0404 }, { 0x17, 0x8006 }, { 0x15, 0x0132 }, { 0x17, 0x8006 },
  { 0x15, 0x0232 }, { 0x17, 0x800D }, { 0x15, 0x000F }, { 0x18, 0x0420 },
  { 0, 0 }
 };
-BCOM_HACK BcomRegC0Hack[] = {
+static BCOM_HACK BcomRegC0Hack[] = {
  { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1204 }, { 0x17, 0x0013 },
  { 0x15, 0x0A04 }, { 0x18, 0x0420 },
  { 0, 0 }
@@ -790,7 +790,7 @@ int		Port)	/* Port Index (MAC_1 + n) */
  * Returns:
  *	nothing
  */
-void SkMacFlushRxFifo(
+static void SkMacFlushRxFifo(
 SK_AC	*pAC,	/* adapter context */
 SK_IOC	IoC,	/* IO context */
 int		Port)	/* Port Index (MAC_1 + n) */
@@ -1231,38 +1231,6 @@ int		Port)	/* Port Index (MAC_1 + n) */
 }	/* SkMacHardRst */
 
 
-/******************************************************************************
- *
- *	SkMacClearRst() - Clear the MAC reset
- *
- * Description:	calls a clear MAC reset routine dep. on board type
- *
- * Returns:
- *	nothing
- */
-void SkMacClearRst(
-SK_AC	*pAC,	/* adapter context */
-SK_IOC	IoC,	/* IO context */
-int		Port)	/* Port Index (MAC_1 + n) */
-{
-	
-#ifdef GENESIS
-	if (pAC->GIni.GIGenesis) {
-		
-		SkXmClearRst(pAC, IoC, Port);
-	}
-#endif /* GENESIS */
-	
-#ifdef YUKON
-	if (pAC->GIni.GIYukon) {
-		
-		SkGmClearRst(pAC, IoC, Port);
-	}
-#endif /* YUKON */
-
-}	/* SkMacClearRst */
-
-
 #ifdef GENESIS
 /******************************************************************************
  *
@@ -1713,7 +1681,7 @@ int		Port)		/* Port Index (MAC_1 + n) */
  * Returns:
  *	nothing
  */
-void SkXmInitDupMd(
+static void SkXmInitDupMd(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* IO context */
 int		Port)		/* Port Index (MAC_1 + n) */
@@ -1761,7 +1729,7 @@ int		Port)		/* Port Index (MAC_1 + n) */
  * Returns:
  *	nothing
  */
-void SkXmInitPauseMd(
+static void SkXmInitPauseMd(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* IO context */
 int		Port)		/* Port Index (MAC_1 + n) */
@@ -2076,283 +2044,7 @@ SK_BOOL	DoLoop)		/* Should a Phy LoopBack be set-up? */
 }	/* SkXmInitPhyBcom */
 #endif /* GENESIS */
 
-
 #ifdef YUKON
-#ifndef SK_SLIM
-/******************************************************************************
- *
- *	SkGmEnterLowPowerMode()
- *
- * Description:	
- *	This function sets the Marvell Alaska PHY to the low power mode
- *	given by parameter mode.
- *	The following low power modes are available:
- *		
- *		- Coma Mode (Deep Sleep):
- *			Power consumption: ~15 - 30 mW
- *			The PHY cannot wake up on its own.
- *
- *		- IEEE 22.2.4.1.5 compatible power down mode
- *			Power consumption: ~240 mW
- *			The PHY cannot wake up on its own.
- *
- *		- energy detect mode
- *			Power consumption: ~160 mW
- *			The PHY can wake up on its own by detecting activity
- *			on the CAT 5 cable.
- *
- *		- energy detect plus mode
- *			Power consumption: ~150 mW
- *			The PHY can wake up on its own by detecting activity
- *			on the CAT 5 cable.
- *			Connected devices can be woken up by sending normal link
- *			pulses every one second.
- *
- * Note:
- *
- * Returns:
- *		0: ok
- *		1: error
- */
-int SkGmEnterLowPowerMode(
-SK_AC	*pAC,		/* adapter context */
-SK_IOC	IoC,		/* IO context */
-int		Port,		/* Port Index (e.g. MAC_1) */
-SK_U8	Mode)		/* low power mode */
-{
-	SK_U16	Word;
-	SK_U32	DWord;
-	SK_U8	LastMode;
-	int		Ret = 0;
-
-	if (pAC->GIni.GIYukonLite &&
-	    pAC->GIni.GIChipRev >= CHIP_REV_YU_LITE_A3) {
-
-		/* save current power mode */
-		LastMode = pAC->GIni.GP[Port].PPhyPowerState;
-		pAC->GIni.GP[Port].PPhyPowerState = Mode;
-
-		switch (Mode) {
-			/* coma mode (deep sleep) */
-			case PHY_PM_DEEP_SLEEP:
-				/* setup General Purpose Control Register */
-				GM_OUT16(IoC, 0, GM_GP_CTRL, GM_GPCR_FL_PASS |
-					GM_GPCR_SPEED_100 | GM_GPCR_AU_ALL_DIS);
-
-				/* apply COMA mode workaround */
-				SkGmPhyWrite(pAC, IoC, Port, 29, 0x001f);
-				SkGmPhyWrite(pAC, IoC, Port, 30, 0xfff3);
-
-				SK_IN32(IoC, PCI_C(PCI_OUR_REG_1), &DWord);
-
-				SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-				
-				/* Set PHY to Coma Mode */
-				SK_OUT32(IoC, PCI_C(PCI_OUR_REG_1), DWord | PCI_PHY_COMA);
-				
-				SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-
-			break;
-			
-			/* IEEE 22.2.4.1.5 compatible power down mode */
-			case PHY_PM_IEEE_POWER_DOWN:
-				/*
-				 * - disable MAC 125 MHz clock
-				 * - allow MAC power down
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-				Word |= PHY_M_PC_DIS_125CLK;
-				Word &=	~PHY_M_PC_MAC_POW_UP;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-
-				/*
-				 * register changes must be followed by a software
-				 * reset to take effect
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &Word);
-				Word |= PHY_CT_RESET;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, Word);
-
-				/* switch IEEE compatible power down mode on */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &Word);
-				Word |= PHY_CT_PDOWN;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, Word);
-			break;
-
-			/* energy detect and energy detect plus mode */
-			case PHY_PM_ENERGY_DETECT:
-			case PHY_PM_ENERGY_DETECT_PLUS:
-				/*
-				 * - disable MAC 125 MHz clock
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-				Word |= PHY_M_PC_DIS_125CLK;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-				
-				/* activate energy detect mode 1 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-
-				/* energy detect mode */
-				if (Mode == PHY_PM_ENERGY_DETECT) {
-					Word |= PHY_M_PC_EN_DET;
-				}
-				/* energy detect plus mode */
-				else {
-					Word |= PHY_M_PC_EN_DET_PLUS;
-				}
-
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-
-				/*
-				 * reinitialize the PHY to force a software reset
-				 * which is necessary after the register settings
-				 * for the energy detect modes.
-				 * Furthermore reinitialisation prevents that the
-				 * PHY is running out of a stable state.
-				 */
-				SkGmInitPhyMarv(pAC, IoC, Port, SK_FALSE);
-			break;
-
-			/* don't change current power mode */
-			default:
-				pAC->GIni.GP[Port].PPhyPowerState = LastMode;
-				Ret = 1;
-			break;
-		}
-	}
-	/* low power modes are not supported by this chip */
-	else {
-		Ret = 1;
-	}
-
-	return(Ret);
-
-}	/* SkGmEnterLowPowerMode */
-
-/******************************************************************************
- *
- *	SkGmLeaveLowPowerMode()
- *
- * Description:	
- *	Leave the current low power mode and switch to normal mode
- *
- * Note:
- *
- * Returns:
- *		0:	ok
- *		1:	error
- */
-int SkGmLeaveLowPowerMode(
-SK_AC	*pAC,		/* adapter context */
-SK_IOC	IoC,		/* IO context */
-int		Port)		/* Port Index (e.g. MAC_1) */
-{
-	SK_U32	DWord;
-	SK_U16	Word;
-	SK_U8	LastMode;
-	int		Ret = 0;
-
-	if (pAC->GIni.GIYukonLite &&
-		pAC->GIni.GIChipRev >= CHIP_REV_YU_LITE_A3) {
-
-		/* save current power mode */
-		LastMode = pAC->GIni.GP[Port].PPhyPowerState;
-		pAC->GIni.GP[Port].PPhyPowerState = PHY_PM_OPERATIONAL_MODE;
-
-		switch (LastMode) {
-			/* coma mode (deep sleep) */
-			case PHY_PM_DEEP_SLEEP:
-				SK_IN32(IoC, PCI_C(PCI_OUR_REG_1), &DWord);
-
-				SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-				
-				/* Release PHY from Coma Mode */
-				SK_OUT32(IoC, PCI_C(PCI_OUR_REG_1), DWord & ~PCI_PHY_COMA);
-				
-				SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-				
-				SK_IN32(IoC, B2_GP_IO, &DWord);
-
-				/* set to output */
-				DWord |= (GP_DIR_9 | GP_IO_9);
-
-				/* set PHY reset */
-				SK_OUT32(IoC, B2_GP_IO, DWord);
-
-				DWord &= ~GP_IO_9; /* clear PHY reset (active high) */
-
-				/* clear PHY reset */
-				SK_OUT32(IoC, B2_GP_IO, DWord);
-			break;
-			
-			/* IEEE 22.2.4.1.5 compatible power down mode */
-			case PHY_PM_IEEE_POWER_DOWN:
-				/*
-				 * - enable MAC 125 MHz clock
-				 * - set MAC power up
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-				Word &= ~PHY_M_PC_DIS_125CLK;
-				Word |=	PHY_M_PC_MAC_POW_UP;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-
-				/*
-				 * register changes must be followed by a software
-				 * reset to take effect
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &Word);
-				Word |= PHY_CT_RESET;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, Word);
-
-				/* switch IEEE compatible power down mode off */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_CTRL, &Word);
-				Word &= ~PHY_CT_PDOWN;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_CTRL, Word);
-			break;
-
-			/* energy detect and energy detect plus mode */
-			case PHY_PM_ENERGY_DETECT:
-			case PHY_PM_ENERGY_DETECT_PLUS:
-				/*
-				 * - enable MAC 125 MHz clock
-				 */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-				Word &= ~PHY_M_PC_DIS_125CLK;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-				
-				/* disable energy detect mode */
-				SkGmPhyRead(pAC, IoC, Port, PHY_MARV_PHY_CTRL, &Word);
-				Word &= ~PHY_M_PC_EN_DET_MSK;
-				SkGmPhyWrite(pAC, IoC, Port, PHY_MARV_PHY_CTRL, Word);
-
-				/*
-				 * reinitialize the PHY to force a software reset
-				 * which is necessary after the register settings
-				 * for the energy detect modes.
-				 * Furthermore reinitialisation prevents that the
-				 * PHY is running out of a stable state.
-				 */
-				SkGmInitPhyMarv(pAC, IoC, Port, SK_FALSE);
-			break;
-
-			/* don't change current power mode */
-			default:
-				pAC->GIni.GP[Port].PPhyPowerState = LastMode;
-				Ret = 1;
-			break;
-		}
-	}
-	/* low power modes are not supported by this chip */
-	else {
-		Ret = 1;
-	}
-
-	return(Ret);
-
-}	/* SkGmLeaveLowPowerMode */
-#endif /* !SK_SLIM */
-
-
 /******************************************************************************
  *
  *	SkGmInitPhyMarv() - Initialize the Marvell Phy registers
@@ -3420,145 +3112,6 @@ int		Port)		/* Port Index (MAC_1 + n) */
 }	/* SkMacAutoNegDone */
 
 
-#ifdef GENESIS
-/******************************************************************************
- *
- *	SkXmSetRxTxEn() - Special Set Rx/Tx Enable and some features in XMAC
- *
- * Description:
- *  sets MAC or PHY LoopBack and Duplex Mode in the MMU Command Reg.
- *  enables Rx/Tx
- *
- * Returns: N/A
- */
-static void SkXmSetRxTxEn(
-SK_AC	*pAC,		/* Adapter Context */
-SK_IOC	IoC,		/* IO context */
-int		Port,		/* Port Index (MAC_1 + n) */
-int		Para)		/* Parameter to set: MAC or PHY LoopBack, Duplex Mode */
-{
-	SK_U16	Word;
-
-	XM_IN16(IoC, Port, XM_MMU_CMD, &Word);
-
-	switch (Para & (SK_MAC_LOOPB_ON | SK_MAC_LOOPB_OFF)) {
-	case SK_MAC_LOOPB_ON:
-		Word |= XM_MMU_MAC_LB;
-		break;
-	case SK_MAC_LOOPB_OFF:
-		Word &= ~XM_MMU_MAC_LB;
-		break;
-	}
-
-	switch (Para & (SK_PHY_LOOPB_ON | SK_PHY_LOOPB_OFF)) {
-	case SK_PHY_LOOPB_ON:
-		Word |= XM_MMU_GMII_LOOP;
-		break;
-	case SK_PHY_LOOPB_OFF:
-		Word &= ~XM_MMU_GMII_LOOP;
-		break;
-	}
-	
-	switch (Para & (SK_PHY_FULLD_ON | SK_PHY_FULLD_OFF)) {
-	case SK_PHY_FULLD_ON:
-		Word |= XM_MMU_GMII_FD;
-		break;
-	case SK_PHY_FULLD_OFF:
-		Word &= ~XM_MMU_GMII_FD;
-		break;
-	}
-	
-	XM_OUT16(IoC, Port, XM_MMU_CMD, Word | XM_MMU_ENA_RX | XM_MMU_ENA_TX);
-
-	/* dummy read to ensure writing */
-	XM_IN16(IoC, Port, XM_MMU_CMD, &Word);
-
-}	/* SkXmSetRxTxEn */
-#endif /* GENESIS */
-
-
-#ifdef YUKON
-/******************************************************************************
- *
- *	SkGmSetRxTxEn() - Special Set Rx/Tx Enable and some features in GMAC
- *
- * Description:
- *  sets MAC LoopBack and Duplex Mode in the General Purpose Control Reg.
- *  enables Rx/Tx
- *
- * Returns: N/A
- */
-static void SkGmSetRxTxEn(
-SK_AC	*pAC,		/* Adapter Context */
-SK_IOC	IoC,		/* IO context */
-int		Port,		/* Port Index (MAC_1 + n) */
-int		Para)		/* Parameter to set: MAC LoopBack, Duplex Mode */
-{
-	SK_U16	Ctrl;
-	
-	GM_IN16(IoC, Port, GM_GP_CTRL, &Ctrl);
-
-	switch (Para & (SK_MAC_LOOPB_ON | SK_MAC_LOOPB_OFF)) {
-	case SK_MAC_LOOPB_ON:
-		Ctrl |= GM_GPCR_LOOP_ENA;
-		break;
-	case SK_MAC_LOOPB_OFF:
-		Ctrl &= ~GM_GPCR_LOOP_ENA;
-		break;
-	}
-
-	switch (Para & (SK_PHY_FULLD_ON | SK_PHY_FULLD_OFF)) {
-	case SK_PHY_FULLD_ON:
-		Ctrl |= GM_GPCR_DUP_FULL;
-		break;
-	case SK_PHY_FULLD_OFF:
-		Ctrl &= ~GM_GPCR_DUP_FULL;
-		break;
-	}
-	
-    GM_OUT16(IoC, Port, GM_GP_CTRL, (SK_U16)(Ctrl | GM_GPCR_RX_ENA |
-		GM_GPCR_TX_ENA));
-
-	/* dummy read to ensure writing */
-	GM_IN16(IoC, Port, GM_GP_CTRL, &Ctrl);
-
-}	/* SkGmSetRxTxEn */
-#endif /* YUKON */
-
-
-#ifndef SK_SLIM
-/******************************************************************************
- *
- *	SkMacSetRxTxEn() - Special Set Rx/Tx Enable and parameters
- *
- * Description:	calls the Special Set Rx/Tx Enable routines dep. on board type
- *
- * Returns: N/A
- */
-void SkMacSetRxTxEn(
-SK_AC	*pAC,		/* Adapter Context */
-SK_IOC	IoC,		/* IO context */
-int		Port,		/* Port Index (MAC_1 + n) */
-int		Para)
-{
-#ifdef GENESIS
-	if (pAC->GIni.GIGenesis) {
-		
-		SkXmSetRxTxEn(pAC, IoC, Port, Para);
-	}
-#endif /* GENESIS */
-	
-#ifdef YUKON
-	if (pAC->GIni.GIYukon) {
-		
-		SkGmSetRxTxEn(pAC, IoC, Port, Para);
-	}
-#endif /* YUKON */
-
-}	/* SkMacSetRxTxEn */
-#endif /* !SK_SLIM */
-
-
 /******************************************************************************
  *
  *	SkMacRxTxEnable() - Enable Rx/Tx activity if port is up
@@ -3976,7 +3529,7 @@ SK_U16	PhyStat)	/* PHY Status word to analyse */
  * Returns:
  *	nothing
  */
-void SkXmIrq(
+static void SkXmIrq(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* IO context */
 int		Port)		/* Port Index (MAC_1 + n) */
@@ -4112,7 +3665,7 @@ int		Port)		/* Port Index (MAC_1 + n) */
  * Returns:
  *	nothing
  */
-void SkGmIrq(
+static void SkGmIrq(
 SK_AC	*pAC,		/* adapter context */
 SK_IOC	IoC,		/* IO context */
 int		Port)		/* Port Index (MAC_1 + n) */

drivers/net/tokenring/lanstreamer.c

@@ -122,6 +122,7 @@
 #include <linux/spinlock.h>
 #include <linux/version.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <net/checksum.h>
 
@@ -512,7 +513,7 @@ static int streamer_reset(struct net_device *dev)
 
 	while (!((readw(streamer_mmio + SISR)) & SISR_SRB_REPLY)) {
 		msleep_interruptible(100);
-		if (jiffies - t > 40 * HZ) {
+		if (time_after(jiffies, t + 40 * HZ)) {
 			printk(KERN_ERR
 			       "IBM PCI tokenring card not responding\n");
 			release_region(dev->base_addr, STREAMER_IO_SPACE);

drivers/net/tokenring/olympic.c

@@ -100,6 +100,7 @@
 #include <linux/pci.h>
 #include <linux/spinlock.h>
 #include <linux/bitops.h>
+#include <linux/jiffies.h>
 
 #include <net/checksum.h>
 
@@ -307,7 +308,7 @@ static int __devinit olympic_init(struct net_device *dev)
 	t=jiffies;
 	while((readl(olympic_mmio+BCTL)) & BCTL_SOFTRESET) {
 		schedule();		
-		if(jiffies-t > 40*HZ) {
+		if(time_after(jiffies, t + 40*HZ)) {
 			printk(KERN_ERR "IBM PCI tokenring card not responding.\n");
 			return -ENODEV;
 		}
@@ -359,7 +360,7 @@ static int __devinit olympic_init(struct net_device *dev)
 		t=jiffies;
 		while (!readl(olympic_mmio+CLKCTL) & CLKCTL_PAUSE) { 
 			schedule() ; 
-			if(jiffies-t > 2*HZ) { 
+			if(time_after(jiffies, t + 2*HZ)) {
 				printk(KERN_ERR "IBM Cardbus tokenring adapter not responsing.\n") ; 
 				return -ENODEV;
 			}
@@ -373,7 +374,7 @@ static int __devinit olympic_init(struct net_device *dev)
 	t=jiffies;
 	while(!((readl(olympic_mmio+SISR_RR)) & SISR_SRB_REPLY)) {
 		schedule();		
-		if(jiffies-t > 15*HZ) {
+		if(time_after(jiffies, t + 15*HZ)) {
 			printk(KERN_ERR "IBM PCI tokenring card not responding.\n");
 			return -ENODEV;
 		}
@@ -519,7 +520,7 @@ static int olympic_open(struct net_device *dev)
             			olympic_priv->srb_queued=0;
             			break;
         		}
-			if ((jiffies-t) > 10*HZ) { 
+			if (time_after(jiffies, t + 10*HZ)) {
 				printk(KERN_WARNING "%s: SRB timed out. \n",dev->name) ; 
 				olympic_priv->srb_queued=0;
 				break ; 

drivers/net/tulip/pnic.c

@@ -16,6 +16,7 @@
 
 #include <linux/kernel.h>
 #include <linux/pci.h>
+#include <linux/jiffies.h>
 #include "tulip.h"
 
 
@@ -68,7 +69,7 @@ void pnic_lnk_change(struct net_device *dev, int csr5)
 		 */
 		if (tulip_media_cap[dev->if_port] & MediaIsMII)
 			return;
-		if (! tp->nwayset  ||  jiffies - dev->trans_start > 1*HZ) {
+		if (! tp->nwayset  ||  time_after(jiffies, dev->trans_start + 1*HZ)) {
 			tp->csr6 = 0x00420000 | (tp->csr6 & 0x0000fdff);
 			iowrite32(tp->csr6, ioaddr + CSR6);
 			iowrite32(0x30, ioaddr + CSR12);

drivers/net/wireless/strip.c

@@ -112,7 +112,7 @@ static const char StripVersion[] = "1.3A-STUART.CHESHIRE";
 #include <linux/ip.h>
 #include <linux/tcp.h>
 #include <linux/time.h>
-
+#include <linux/jiffies.h>
 
 /************************************************************************/
 /* Useful structures and definitions					*/
@@ -1569,7 +1569,7 @@ static int strip_xmit(struct sk_buff *skb, struct net_device *dev)
 	del_timer(&strip_info->idle_timer);
 
 
-	if (jiffies - strip_info->pps_timer > HZ) {
+	if (time_after(jiffies, strip_info->pps_timer + HZ)) {
 		unsigned long t = jiffies - strip_info->pps_timer;
 		unsigned long rx_pps_count = (strip_info->rx_pps_count * HZ * 8 + t / 2) / t;
 		unsigned long tx_pps_count = (strip_info->tx_pps_count * HZ * 8 + t / 2) / t;

drivers/net/zorro8390.c

@@ -27,6 +27,7 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/zorro.h>
+#include <linux/jiffies.h>
 
 #include <asm/system.h>
 #include <asm/irq.h>
@@ -151,7 +152,7 @@ static int __devinit zorro8390_init(struct net_device *dev,
 	z_writeb(z_readb(ioaddr + NE_RESET), ioaddr + NE_RESET);
 
 	while ((z_readb(ioaddr + NE_EN0_ISR) & ENISR_RESET) == 0)
-	    if (jiffies - reset_start_time > 2*HZ/100) {
+	    if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 		printk(KERN_WARNING " not found (no reset ack).\n");
 		return -ENODEV;
 	    }
@@ -273,7 +274,7 @@ static void zorro8390_reset_8390(struct net_device *dev)
 
     /* This check _should_not_ be necessary, omit eventually. */
     while ((z_readb(NE_BASE+NE_EN0_ISR) & ENISR_RESET) == 0)
-	if (jiffies - reset_start_time > 2*HZ/100) {
+	if (time_after(jiffies, reset_start_time + 2*HZ/100)) {
 	    printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n",
 		   dev->name);
 	    break;
@@ -400,7 +401,7 @@ static void zorro8390_block_output(struct net_device *dev, int count,
     dma_start = jiffies;
 
     while ((z_readb(NE_BASE + NE_EN0_ISR) & ENISR_RDC) == 0)
-	if (jiffies - dma_start > 2*HZ/100) {		/* 20ms */
+	if (time_after(jiffies, dma_start + 2*HZ/100)) {	/* 20ms */
 		printk(KERN_ERR "%s: timeout waiting for Tx RDC.\n",
 		       dev->name);
 		zorro8390_reset_8390(dev);

include/linux/arcdevice.h

@@ -206,7 +206,6 @@ struct ArcProto {
 
 extern struct ArcProto *arc_proto_map[256], *arc_proto_default,
 	*arc_bcast_proto, *arc_raw_proto;
-extern struct ArcProto arc_proto_null;
 
 
 /*
@@ -334,17 +333,9 @@ void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc);
 #define arcnet_dump_skb(dev,skb,desc) ;
 #endif
 
-#if (ARCNET_DEBUG_MAX & D_RX) || (ARCNET_DEBUG_MAX & D_TX)
-void arcnet_dump_packet(struct net_device *dev, int bufnum, char *desc,
-			int take_arcnet_lock);
-#else
-#define arcnet_dump_packet(dev, bufnum, desc,take_arcnet_lock) ;
-#endif
-
 void arcnet_unregister_proto(struct ArcProto *proto);
 irqreturn_t arcnet_interrupt(int irq, void *dev_id, struct pt_regs *regs);
 struct net_device *alloc_arcdev(char *name);
-void arcnet_rx(struct net_device *dev, int bufnum);
 
 #endif				/* __KERNEL__ */
 #endif				/* _LINUX_ARCDEVICE_H */