iwlwifi: add iwl5000_tx_response structure

This patch adds iwl5000_tx_repsons structure.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-commands.h

@@ -1419,6 +1419,11 @@ enum {
  *     within the sending station (this 4965), rather than whether it was
  *     received successfully by the destination station.
  */
+struct agg_tx_status {
+	__le16 status;
+	__le16 sequence;
+} __attribute__ ((packed));
+
 struct iwl4965_tx_resp {
 	u8 frame_count;		/* 1 no aggregation, >1 aggregation */
 	u8 bt_kill_count;	/* # blocked by bluetooth (unused for agg) */
@@ -1453,11 +1458,6 @@ struct iwl4965_tx_resp {
 	__le32 status;	/* TX status (for aggregation status of 1st frame) */
 } __attribute__ ((packed));
 
-struct agg_tx_status {
-	__le16 status;
-	__le16 sequence;
-} __attribute__ ((packed));
-
 struct iwl4965_tx_resp_agg {
 	u8 frame_count;         /* 1 no aggregation, >1 aggregation */
 	u8 reserved1;
@@ -1472,6 +1472,44 @@ struct iwl4965_tx_resp_agg {
 					/* of 1st frame) */
 } __attribute__ ((packed));
 
+struct iwl5000_tx_resp {
+	u8 frame_count;		/* 1 no aggregation, >1 aggregation */
+	u8 bt_kill_count;	/* # blocked by bluetooth (unused for agg) */
+	u8 failure_rts;		/* # failures due to unsuccessful RTS */
+	u8 failure_frame;	/* # failures due to no ACK (unused for agg) */
+
+	/* For non-agg:  Rate at which frame was successful.
+	 * For agg:  Rate at which all frames were transmitted. */
+	__le32 rate_n_flags;	/* RATE_MCS_*  */
+
+	/* For non-agg:  RTS + CTS + frame tx attempts time + ACK.
+	 * For agg:  RTS + CTS + aggregation tx time + block-ack time. */
+	__le16 wireless_media_time;	/* uSecs */
+
+	__le16 reserved;
+	__le32 pa_power1;	/* RF power amplifier measurement (not used) */
+	__le32 pa_power2;
+
+	__le32 tfd_info;
+	__le16 seq_ctl;
+	__le16 byte_cnt;
+	__le32 tlc_info;
+	/*
+	 * For non-agg:  frame status TX_STATUS_*
+	 * For agg:  status of 1st frame, AGG_TX_STATE_*; other frame status
+	 *           fields follow this one, up to frame_count.
+	 *           Bit fields:
+	 *           11- 0:  AGG_TX_STATE_* status code
+	 *           15-12:  Retry count for 1st frame in aggregation (retries
+	 *                   occur if tx failed for this frame when it was a
+	 *                   member of a previous aggregation block).  If rate
+	 *                   scaling is used, retry count indicates the rate
+	 *                   table entry used for all frames in the new agg.
+	 *           31-16:  Sequence # for this frame's Tx cmd (not SSN!)
+	 */
+	struct agg_tx_status status;	/* TX status (in aggregation -
+					 * status of 1st frame) */
+} __attribute__ ((packed));
 /*
  * REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
  *